diff options
Diffstat (limited to 'drivers/ata/pata_hpt3x3.c')
| -rw-r--r-- | drivers/ata/pata_hpt3x3.c | 226 |
1 files changed, 226 insertions, 0 deletions
diff --git a/drivers/ata/pata_hpt3x3.c b/drivers/ata/pata_hpt3x3.c new file mode 100644 index 000000000000..152770133ab1 --- /dev/null +++ b/drivers/ata/pata_hpt3x3.c @@ -0,0 +1,226 @@ +/* + * pata_hpt3x3 - HPT3x3 driver + * (c) Copyright 2005-2006 Red Hat + * + * Was pata_hpt34x but the naming was confusing as it supported the + * 343 and 363 so it has been renamed. + * + * Based on: + * linux/drivers/ide/pci/hpt34x.c Version 0.40 Sept 10, 2002 + * Copyright (C) 1998-2000 Andre Hedrick <andre@linux-ide.org> + * + * May be copied or modified under the terms of the GNU General Public + * License + */ + +#include <linux/kernel.h> +#include <linux/module.h> +#include <linux/pci.h> +#include <linux/init.h> +#include <linux/blkdev.h> +#include <linux/delay.h> +#include <scsi/scsi_host.h> +#include <linux/libata.h> + +#define DRV_NAME "pata_hpt3x3" +#define DRV_VERSION "0.4.1" + +static int hpt3x3_probe_init(struct ata_port *ap) +{ + ap->cbl = ATA_CBL_PATA40; + return ata_std_prereset(ap); +} + +/** + * hpt3x3_probe_reset - reset the hpt3x3 bus + * @ap: ATA port to reset + * + * Perform the housekeeping when doing an ATA bus reeset. We just + * need to force the cable type. + */ + +static void hpt3x3_error_handler(struct ata_port *ap) +{ + return ata_bmdma_drive_eh(ap, hpt3x3_probe_init, ata_std_softreset, NULL, ata_std_postreset); +} + +/** + * hpt3x3_set_piomode - PIO setup + * @ap: ATA interface + * @adev: device on the interface + * + * Set our PIO requirements. This is fairly simple on the HPT3x3 as + * all we have to do is clear the MWDMA and UDMA bits then load the + * mode number. + */ + +static void hpt3x3_set_piomode(struct ata_port *ap, struct ata_device *adev) +{ + struct pci_dev *pdev = to_pci_dev(ap->host->dev); + u32 r1, r2; + int dn = 2 * ap->port_no + adev->devno; + + pci_read_config_dword(pdev, 0x44, &r1); + pci_read_config_dword(pdev, 0x48, &r2); + /* Load the PIO timing number */ + r1 &= ~(7 << (3 * dn)); + r1 |= (adev->pio_mode - XFER_PIO_0) << (3 * dn); + r2 &= ~(0x11 << dn); /* Clear MWDMA and UDMA bits */ + + pci_write_config_dword(pdev, 0x44, r1); + pci_write_config_dword(pdev, 0x48, r2); +} + +/** + * hpt3x3_set_dmamode - DMA timing setup + * @ap: ATA interface + * @adev: Device being configured + * + * Set up the channel for MWDMA or UDMA modes. Much the same as with + * PIO, load the mode number and then set MWDMA or UDMA flag. + */ + +static void hpt3x3_set_dmamode(struct ata_port *ap, struct ata_device *adev) +{ + struct pci_dev *pdev = to_pci_dev(ap->host->dev); + u32 r1, r2; + int dn = 2 * ap->port_no + adev->devno; + int mode_num = adev->dma_mode & 0x0F; + + pci_read_config_dword(pdev, 0x44, &r1); + pci_read_config_dword(pdev, 0x48, &r2); + /* Load the timing number */ + r1 &= ~(7 << (3 * dn)); + r1 |= (mode_num << (3 * dn)); + r2 &= ~(0x11 << dn); /* Clear MWDMA and UDMA bits */ + + if (adev->dma_mode >= XFER_UDMA_0) + r2 |= 0x01 << dn; /* Ultra mode */ + else + r2 |= 0x10 << dn; /* MWDMA */ + + pci_write_config_dword(pdev, 0x44, r1); + pci_write_config_dword(pdev, 0x48, r2); +} + +static struct scsi_host_template hpt3x3_sht = { + .module = THIS_MODULE, + .name = DRV_NAME, + .ioctl = ata_scsi_ioctl, + .queuecommand = ata_scsi_queuecmd, + .can_queue = ATA_DEF_QUEUE, + .this_id = ATA_SHT_THIS_ID, + .sg_tablesize = LIBATA_MAX_PRD, + .max_sectors = ATA_MAX_SECTORS, + .cmd_per_lun = ATA_SHT_CMD_PER_LUN, + .emulated = ATA_SHT_EMULATED, + .use_clustering = ATA_SHT_USE_CLUSTERING, + .proc_name = DRV_NAME, + .dma_boundary = ATA_DMA_BOUNDARY, + .slave_configure = ata_scsi_slave_config, + .bios_param = ata_std_bios_param, +}; + +static struct ata_port_operations hpt3x3_port_ops = { + .port_disable = ata_port_disable, + .set_piomode = hpt3x3_set_piomode, + .set_dmamode = hpt3x3_set_dmamode, + .mode_filter = ata_pci_default_filter, + + .tf_load = ata_tf_load, + .tf_read = ata_tf_read, + .check_status = ata_check_status, + .exec_command = ata_exec_command, + .dev_select = ata_std_dev_select, + + .freeze = ata_bmdma_freeze, + .thaw = ata_bmdma_thaw, + .error_handler = hpt3x3_error_handler, + .post_internal_cmd = ata_bmdma_post_internal_cmd, + + .bmdma_setup = ata_bmdma_setup, + .bmdma_start = ata_bmdma_start, + .bmdma_stop = ata_bmdma_stop, + .bmdma_status = ata_bmdma_status, + + .qc_prep = ata_qc_prep, + .qc_issue = ata_qc_issue_prot, + .eng_timeout = ata_eng_timeout, + .data_xfer = ata_pio_data_xfer, + + .irq_handler = ata_interrupt, + .irq_clear = ata_bmdma_irq_clear, + + .port_start = ata_port_start, + .port_stop = ata_port_stop, + .host_stop = ata_host_stop +}; + +/** + * hpt3x3_init_one - Initialise an HPT343/363 + * @dev: PCI device + * @id: Entry in match table + * + * Perform basic initialisation. The chip has a quirk that it won't + * function unless it is at XX00. The old ATA driver touched this up + * but we leave it for pci quirks to do properly. + */ + +static int hpt3x3_init_one(struct pci_dev *dev, const struct pci_device_id *id) +{ + static struct ata_port_info info = { + .sht = &hpt3x3_sht, + .flags = ATA_FLAG_SLAVE_POSS|ATA_FLAG_SRST, + .pio_mask = 0x1f, + .mwdma_mask = 0x07, + .udma_mask = 0x07, + .port_ops = &hpt3x3_port_ops + }; + static struct ata_port_info *port_info[2] = { &info, &info }; + u16 cmd; + + /* Initialize the board */ + pci_write_config_word(dev, 0x80, 0x00); + /* Check if it is a 343 or a 363. 363 has COMMAND_MEMORY set */ + pci_read_config_word(dev, PCI_COMMAND, &cmd); + if (cmd & PCI_COMMAND_MEMORY) + pci_write_config_byte(dev, PCI_LATENCY_TIMER, 0xF0); + else + pci_write_config_byte(dev, PCI_LATENCY_TIMER, 0x20); + + /* Now kick off ATA set up */ + return ata_pci_init_one(dev, port_info, 2); +} + +static struct pci_device_id hpt3x3[] = { + { PCI_DEVICE(PCI_VENDOR_ID_TTI, PCI_DEVICE_ID_TTI_HPT343), }, + { 0, }, +}; + +static struct pci_driver hpt3x3_pci_driver = { + .name = DRV_NAME, + .id_table = hpt3x3, + .probe = hpt3x3_init_one, + .remove = ata_pci_remove_one +}; + +static int __init hpt3x3_init(void) +{ + return pci_register_driver(&hpt3x3_pci_driver); +} + + +static void __exit hpt3x3_exit(void) +{ + pci_unregister_driver(&hpt3x3_pci_driver); +} + + +MODULE_AUTHOR("Alan Cox"); +MODULE_DESCRIPTION("low-level driver for the Highpoint HPT343/363"); +MODULE_LICENSE("GPL"); +MODULE_DEVICE_TABLE(pci, hpt3x3); +MODULE_VERSION(DRV_VERSION); + +module_init(hpt3x3_init); +module_exit(hpt3x3_exit); |