1 files changed, 335 insertions, 0 deletions
diff --git a/drivers/ata/pata_radisys.c b/drivers/ata/pata_radisys.c
new file mode 100644
index 000000000000..6f7d0527265f
--- /dev/null
+++ b/drivers/ata/pata_radisys.c
@@ -0,0 +1,335 @@
+/*
+ *    pata_radisys.c - Intel PATA/SATA controllers
+ *
+ *	(C) 2006 Red Hat <alan@redhat.com>
+ *
+ *    Some parts based on ata_piix.c by Jeff Garzik and others.
+ *
+ *    A PIIX relative, this device has a single ATA channel and no
+ *    slave timings, SITRE or PPE. In that sense it is a close relative
+ *    of the original PIIX. It does however support UDMA 33/66 per channel
+ *    although no other modes/timings. Also lacking is 32bit I/O on the ATA
+ *    port.
+ */
+
+#include <linux/kernel.h>
+#include <linux/module.h>
+#include <linux/pci.h>
+#include <linux/init.h>
+#include <linux/blkdev.h>
+#include <linux/delay.h>
+#include <linux/device.h>
+#include <scsi/scsi_host.h>
+#include <linux/libata.h>
+#include <linux/ata.h>
+
+#define DRV_NAME	"pata_radisys"
+#define DRV_VERSION	"0.4.1"
+
+/**
+ *	radisys_probe_init		-	probe begin
+ *	@ap: ATA port
+ *
+ *	Set up cable type and use generic probe init
+ */
+ 
+static int radisys_pre_reset(struct ata_port *ap)
+{
+	ap->cbl = ATA_CBL_PATA80;
+	return ata_std_prereset(ap);
+}
+
+
+/**
+ *	radisys_pata_error_handler - Probe specified port on PATA host controller
+ *	@ap: Port to probe
+ *	@classes:
+ *
+ *	LOCKING:
+ *	None (inherited from caller).
+ */
+
+static void radisys_pata_error_handler(struct ata_port *ap)
+{
+	ata_bmdma_drive_eh(ap, radisys_pre_reset, ata_std_softreset, NULL, ata_std_postreset);
+}
+
+/**
+ *	radisys_set_piomode - Initialize host controller PATA PIO timings
+ *	@ap: Port whose timings we are configuring
+ *	@adev: um
+ *
+ *	Set PIO mode for device, in host controller PCI config space.
+ *
+ *	LOCKING:
+ *	None (inherited from caller).
+ */
+
+static void radisys_set_piomode (struct ata_port *ap, struct ata_device *adev)
+{
+	unsigned int pio	= adev->pio_mode - XFER_PIO_0;
+	struct pci_dev *dev	= to_pci_dev(ap->host->dev);
+	u16 idetm_data;
+	int control = 0;
+
+	/*
+	 *	See Intel Document 298600-004 for the timing programing rules
+	 *	for PIIX/ICH. Note that the early PIIX does not have the slave
+	 *	timing port at 0x44. The Radisys is a relative of the PIIX
+	 *	but not the same so be careful.
+	 */
+
+	static const	 /* ISP  RTC */
+	u8 timings[][2]	= { { 0, 0 },	/* Check me */
+			    { 0, 0 },
+			    { 1, 1 },
+			    { 2, 2 },
+			    { 3, 3 }, };
+
+	if (pio > 0)
+		control |= 1;	/* TIME1 enable */
+	if (ata_pio_need_iordy(adev))
+		control |= 2;	/* IE IORDY */
+
+	pci_read_config_word(dev, 0x40, &idetm_data);
+
+	/* Enable IE and TIME as appropriate. Clear the other
+	   drive timing bits */
+	idetm_data &= 0xCCCC;
+	idetm_data |= (control << (4 * adev->devno));
+	idetm_data |= (timings[pio][0] << 12) |
+			(timings[pio][1] << 8);
+	pci_write_config_word(dev, 0x40, idetm_data);
+
+	/* Track which port is configured */
+	ap->private_data = adev;
+}
+
+/**
+ *	radisys_set_dmamode - Initialize host controller PATA DMA timings
+ *	@ap: Port whose timings we are configuring
+ *	@adev: Device to program
+ *	@isich: True if the device is an ICH and has IOCFG registers
+ *
+ *	Set MWDMA mode for device, in host controller PCI config space.
+ *
+ *	LOCKING:
+ *	None (inherited from caller).
+ */
+
+static void radisys_set_dmamode (struct ata_port *ap, struct ata_device *adev)
+{
+	struct pci_dev *dev	= to_pci_dev(ap->host->dev);
+	u16 idetm_data;
+	u8 udma_enable;
+	
+	static const	 /* ISP  RTC */
+	u8 timings[][2]	= { { 0, 0 },
+			    { 0, 0 },
+			    { 1, 1 },
+			    { 2, 2 },
+			    { 3, 3 }, };
+
+	/*
+	 * MWDMA is driven by the PIO timings. We must also enable
+	 * IORDY unconditionally.
+	 */
+
+	pci_read_config_word(dev, 0x40, &idetm_data);
+	pci_read_config_byte(dev, 0x48, &udma_enable);
+
+	if (adev->dma_mode < XFER_UDMA_0) {
+		unsigned int mwdma	= adev->dma_mode - XFER_MW_DMA_0;
+		const unsigned int needed_pio[3] = {
+			XFER_PIO_0, XFER_PIO_3, XFER_PIO_4
+		};
+		int pio = needed_pio[mwdma] - XFER_PIO_0;
+		int control = 3;	/* IORDY|TIME0 */
+
+		/* If the drive MWDMA is faster than it can do PIO then
+		   we must force PIO0 for PIO cycles. */
+
+		if (adev->pio_mode < needed_pio[mwdma])
+			control = 1;
+
+		/* Mask out the relevant control and timing bits we will load. Also
+		   clear the other drive TIME register as a precaution */
+		   
+		idetm_data &= 0xCCCC;
+		idetm_data |= control << (4 * adev->devno);
+		idetm_data |= (timings[pio][0] << 12) | (timings[pio][1] << 8);
+
+		udma_enable &= ~(1 << adev->devno);
+	} else {
+		u8 udma_mode;
+		
+		/* UDMA66 on: UDMA 33 and 66 are switchable via register 0x4A */
+		
+		pci_read_config_byte(dev, 0x4A, &udma_mode);
+		
+		if (adev->xfer_mode == XFER_UDMA_2)
+			udma_mode &= ~ (1 << adev->devno);
+		else /* UDMA 4 */
+			udma_mode |= (1 << adev->devno);
+			
+		pci_write_config_byte(dev, 0x4A, udma_mode);
+		
+		udma_enable |= (1 << adev->devno);
+	}
+	pci_write_config_word(dev, 0x40, idetm_data);
+	pci_write_config_byte(dev, 0x48, udma_enable);
+
+	/* Track which port is configured */
+	ap->private_data = adev;
+}
+
+/**
+ *	radisys_qc_issue_prot	-	command issue
+ *	@qc: command pending
+ *
+ *	Called when the libata layer is about to issue a command. We wrap
+ *	this interface so that we can load the correct ATA timings if
+ *	neccessary. Our logic also clears TIME0/TIME1 for the other device so
+ *	that, even if we get this wrong, cycles to the other device will
+ *	be made PIO0.
+ */
+
+static unsigned int radisys_qc_issue_prot(struct ata_queued_cmd *qc)
+{
+	struct ata_port *ap = qc->ap;
+	struct ata_device *adev = qc->dev;
+
+	if (adev != ap->private_data) {
+		/* UDMA timing is not shared */
+		if (adev->dma_mode < XFER_UDMA_0) {
+			if (adev->dma_mode)
+				radisys_set_dmamode(ap, adev);
+			else if (adev->pio_mode)
+				radisys_set_piomode(ap, adev);
+		}
+	}
+	return ata_qc_issue_prot(qc);
+}
+
+
+static struct scsi_host_template radisys_sht = {
+	.module			= THIS_MODULE,
+	.name			= DRV_NAME,
+	.ioctl			= ata_scsi_ioctl,
+	.queuecommand		= ata_scsi_queuecmd,
+	.can_queue		= ATA_DEF_QUEUE,
+	.this_id		= ATA_SHT_THIS_ID,
+	.sg_tablesize		= LIBATA_MAX_PRD,
+	.max_sectors		= ATA_MAX_SECTORS,
+	.cmd_per_lun		= ATA_SHT_CMD_PER_LUN,
+	.emulated		= ATA_SHT_EMULATED,
+	.use_clustering		= ATA_SHT_USE_CLUSTERING,
+	.proc_name		= DRV_NAME,
+	.dma_boundary		= ATA_DMA_BOUNDARY,
+	.slave_configure	= ata_scsi_slave_config,
+	.bios_param		= ata_std_bios_param,
+};
+
+static const struct ata_port_operations radisys_pata_ops = {
+	.port_disable		= ata_port_disable,
+	.set_piomode		= radisys_set_piomode,
+	.set_dmamode		= radisys_set_dmamode,
+	.mode_filter		= ata_pci_default_filter,
+
+	.tf_load		= ata_tf_load,
+	.tf_read		= ata_tf_read,
+	.check_status		= ata_check_status,
+	.exec_command		= ata_exec_command,
+	.dev_select		= ata_std_dev_select,
+
+	.freeze			= ata_bmdma_freeze,
+	.thaw			= ata_bmdma_thaw,
+	.error_handler		= radisys_pata_error_handler,
+	.post_internal_cmd	= ata_bmdma_post_internal_cmd,
+
+	.bmdma_setup		= ata_bmdma_setup,
+	.bmdma_start		= ata_bmdma_start,
+	.bmdma_stop		= ata_bmdma_stop,
+	.bmdma_status		= ata_bmdma_status,
+	.qc_prep		= ata_qc_prep,
+	.qc_issue		= radisys_qc_issue_prot,
+	.data_xfer		= ata_pio_data_xfer,
+
+	.eng_timeout		= ata_eng_timeout,
+
+	.irq_handler		= ata_interrupt,
+	.irq_clear		= ata_bmdma_irq_clear,
+
+	.port_start		= ata_port_start,
+	.port_stop		= ata_port_stop,
+	.host_stop		= ata_host_stop,
+};
+
+
+/**
+ *	radisys_init_one - Register PIIX ATA PCI device with kernel services
+ *	@pdev: PCI device to register
+ *	@ent: Entry in radisys_pci_tbl matching with @pdev
+ *
+ *	Called from kernel PCI layer.  We probe for combined mode (sigh),
+ *	and then hand over control to libata, for it to do the rest.
+ *
+ *	LOCKING:
+ *	Inherited from PCI layer (may sleep).
+ *
+ *	RETURNS:
+ *	Zero on success, or -ERRNO value.
+ */
+
+static int radisys_init_one (struct pci_dev *pdev, const struct pci_device_id *ent)
+{
+	static int printed_version;
+	static struct ata_port_info info = {
+		.sht		= &radisys_sht,
+		.flags		= ATA_FLAG_SLAVE_POSS | ATA_FLAG_SRST,
+		.pio_mask	= 0x1f,	/* pio0-4 */
+		.mwdma_mask	= 0x07, /* mwdma1-2 */
+		.udma_mask	= 0x14, /* UDMA33/66 only */
+		.port_ops	= &radisys_pata_ops,
+	};
+	static struct ata_port_info *port_info[2] = { &info, &info };
+
+	if (!printed_version++)
+		dev_printk(KERN_DEBUG, &pdev->dev,
+			   "version " DRV_VERSION "\n");
+
+	return ata_pci_init_one(pdev, port_info, 2);
+}
+
+static const struct pci_device_id radisys_pci_tbl[] = {
+	{ 0x1331, 0x8201, PCI_ANY_ID, PCI_ANY_ID, },
+	{ }	/* terminate list */
+};
+
+static struct pci_driver radisys_pci_driver = {
+	.name			= DRV_NAME,
+	.id_table		= radisys_pci_tbl,
+	.probe			= radisys_init_one,
+	.remove			= ata_pci_remove_one,
+};
+
+static int __init radisys_init(void)
+{
+	return pci_register_driver(&radisys_pci_driver);
+}
+
+static void __exit radisys_exit(void)
+{
+	pci_unregister_driver(&radisys_pci_driver);
+}
+
+
+module_init(radisys_init);
+module_exit(radisys_exit);
+
+MODULE_AUTHOR("Alan Cox");
+MODULE_DESCRIPTION("SCSI low-level driver for Radisys R82600 controllers");
+MODULE_LICENSE("GPL");
+MODULE_DEVICE_TABLE(pci, radisys_pci_tbl);
+MODULE_VERSION(DRV_VERSION);
+