summaryrefslogtreecommitdiff
path: root/drivers/dma/amba-pl08x.c
diff options
context:
space:
mode:
Diffstat (limited to 'drivers/dma/amba-pl08x.c')
-rw-r--r--drivers/dma/amba-pl08x.c53
1 files changed, 33 insertions, 20 deletions
diff --git a/drivers/dma/amba-pl08x.c b/drivers/dma/amba-pl08x.c
index 297f48b0cba9..07bca4970e50 100644
--- a/drivers/dma/amba-pl08x.c
+++ b/drivers/dma/amba-pl08x.c
@@ -79,6 +79,7 @@
#include <linux/module.h>
#include <linux/interrupt.h>
#include <linux/slab.h>
+#include <linux/delay.h>
#include <linux/dmapool.h>
#include <linux/dmaengine.h>
#include <linux/amba/bus.h>
@@ -235,16 +236,19 @@ static void pl08x_start_txd(struct pl08x_dma_chan *plchan,
}
/*
- * Overall DMAC remains enabled always.
+ * Pause the channel by setting the HALT bit.
*
- * Disabling individual channels could lose data.
+ * For M->P transfers, pause the DMAC first and then stop the peripheral -
+ * the FIFO can only drain if the peripheral is still requesting data.
+ * (note: this can still timeout if the DMAC FIFO never drains of data.)
*
- * Disable the peripheral DMA after disabling the DMAC in order to allow
- * the DMAC FIFO to drain, and hence allow the channel to show inactive
+ * For P->M transfers, disable the peripheral first to stop it filling
+ * the DMAC FIFO, and then pause the DMAC.
*/
static void pl08x_pause_phy_chan(struct pl08x_phy_chan *ch)
{
u32 val;
+ int timeout;
/* Set the HALT bit and wait for the FIFO to drain */
val = readl(ch->base + PL080_CH_CONFIG);
@@ -252,8 +256,13 @@ static void pl08x_pause_phy_chan(struct pl08x_phy_chan *ch)
writel(val, ch->base + PL080_CH_CONFIG);
/* Wait for channel inactive */
- while (pl08x_phy_channel_busy(ch))
- cpu_relax();
+ for (timeout = 1000; timeout; timeout--) {
+ if (!pl08x_phy_channel_busy(ch))
+ break;
+ udelay(1);
+ }
+ if (pl08x_phy_channel_busy(ch))
+ pr_err("pl08x: channel%u timeout waiting for pause\n", ch->id);
}
static void pl08x_resume_phy_chan(struct pl08x_phy_chan *ch)
@@ -267,19 +276,24 @@ static void pl08x_resume_phy_chan(struct pl08x_phy_chan *ch)
}
-/* Stops the channel */
-static void pl08x_stop_phy_chan(struct pl08x_phy_chan *ch)
+/*
+ * pl08x_terminate_phy_chan() stops the channel, clears the FIFO and
+ * clears any pending interrupt status. This should not be used for
+ * an on-going transfer, but as a method of shutting down a channel
+ * (eg, when it's no longer used) or terminating a transfer.
+ */
+static void pl08x_terminate_phy_chan(struct pl08x_driver_data *pl08x,
+ struct pl08x_phy_chan *ch)
{
- u32 val;
+ u32 val = readl(ch->base + PL080_CH_CONFIG);
- pl08x_pause_phy_chan(ch);
+ val &= ~(PL080_CONFIG_ENABLE | PL080_CONFIG_ERR_IRQ_MASK |
+ PL080_CONFIG_TC_IRQ_MASK);
- /* Disable channel */
- val = readl(ch->base + PL080_CH_CONFIG);
- val &= ~PL080_CONFIG_ENABLE;
- val &= ~PL080_CONFIG_ERR_IRQ_MASK;
- val &= ~PL080_CONFIG_TC_IRQ_MASK;
writel(val, ch->base + PL080_CH_CONFIG);
+
+ writel(1 << ch->id, pl08x->base + PL080_ERR_CLEAR);
+ writel(1 << ch->id, pl08x->base + PL080_TC_CLEAR);
}
static inline u32 get_bytes_in_cctl(u32 cctl)
@@ -404,13 +418,12 @@ static inline void pl08x_put_phy_channel(struct pl08x_driver_data *pl08x,
{
unsigned long flags;
+ spin_lock_irqsave(&ch->lock, flags);
+
/* Stop the channel and clear its interrupts */
- pl08x_stop_phy_chan(ch);
- writel((1 << ch->id), pl08x->base + PL080_ERR_CLEAR);
- writel((1 << ch->id), pl08x->base + PL080_TC_CLEAR);
+ pl08x_terminate_phy_chan(pl08x, ch);
/* Mark it as free */
- spin_lock_irqsave(&ch->lock, flags);
ch->serving = NULL;
spin_unlock_irqrestore(&ch->lock, flags);
}
@@ -1449,7 +1462,7 @@ static int pl08x_control(struct dma_chan *chan, enum dma_ctrl_cmd cmd,
plchan->state = PL08X_CHAN_IDLE;
if (plchan->phychan) {
- pl08x_stop_phy_chan(plchan->phychan);
+ pl08x_terminate_phy_chan(pl08x, plchan->phychan);
/*
* Mark physical channel as free and free any slave