diff options
Diffstat (limited to 'drivers/gpu/drm/radeon/r300_cmdbuf.c')
| -rw-r--r-- | drivers/gpu/drm/radeon/r300_cmdbuf.c | 196 |
1 files changed, 162 insertions, 34 deletions
diff --git a/drivers/gpu/drm/radeon/r300_cmdbuf.c b/drivers/gpu/drm/radeon/r300_cmdbuf.c index 702df45320f7..4b27d9abb7bc 100644 --- a/drivers/gpu/drm/radeon/r300_cmdbuf.c +++ b/drivers/gpu/drm/radeon/r300_cmdbuf.c @@ -77,6 +77,9 @@ static int r300_emit_cliprects(drm_radeon_private_t *dev_priv, return -EFAULT; } + box.x2--; /* Hardware expects inclusive bottom-right corner */ + box.y2--; + if ((dev_priv->flags & RADEON_FAMILY_MASK) >= CHIP_RV515) { box.x1 = (box.x1) & R300_CLIPRECT_MASK; @@ -95,8 +98,8 @@ static int r300_emit_cliprects(drm_radeon_private_t *dev_priv, R300_CLIPRECT_MASK; box.y2 = (box.y2 + R300_CLIPRECT_OFFSET) & R300_CLIPRECT_MASK; - } + OUT_RING((box.x1 << R300_CLIPRECT_X_SHIFT) | (box.y1 << R300_CLIPRECT_Y_SHIFT)); OUT_RING((box.x2 << R300_CLIPRECT_X_SHIFT) | @@ -136,6 +139,18 @@ static int r300_emit_cliprects(drm_radeon_private_t *dev_priv, ADVANCE_RING(); } + /* flus cache and wait idle clean after cliprect change */ + BEGIN_RING(2); + OUT_RING(CP_PACKET0(R300_RB3D_DSTCACHE_CTLSTAT, 0)); + OUT_RING(R300_RB3D_DC_FLUSH); + ADVANCE_RING(); + BEGIN_RING(2); + OUT_RING(CP_PACKET0(RADEON_WAIT_UNTIL, 0)); + OUT_RING(RADEON_WAIT_3D_IDLECLEAN); + ADVANCE_RING(); + /* set flush flag */ + dev_priv->track_flush |= RADEON_FLUSH_EMITED; + return 0; } @@ -166,13 +181,13 @@ void r300_init_reg_flags(struct drm_device *dev) ADD_RANGE(0x21DC, 1); ADD_RANGE(R300_VAP_UNKNOWN_221C, 1); ADD_RANGE(R300_VAP_CLIP_X_0, 4); - ADD_RANGE(R300_VAP_PVS_WAITIDLE, 1); + ADD_RANGE(R300_VAP_PVS_STATE_FLUSH_REG, 1); ADD_RANGE(R300_VAP_UNKNOWN_2288, 1); ADD_RANGE(R300_VAP_OUTPUT_VTX_FMT_0, 2); ADD_RANGE(R300_VAP_PVS_CNTL_1, 3); ADD_RANGE(R300_GB_ENABLE, 1); ADD_RANGE(R300_GB_MSPOS0, 5); - ADD_RANGE(R300_TX_CNTL, 1); + ADD_RANGE(R300_TX_INVALTAGS, 1); ADD_RANGE(R300_TX_ENABLE, 1); ADD_RANGE(0x4200, 4); ADD_RANGE(0x4214, 1); @@ -388,15 +403,28 @@ static __inline__ int r300_emit_vpu(drm_radeon_private_t *dev_priv, if (sz * 16 > cmdbuf->bufsz) return -EINVAL; - BEGIN_RING(5 + sz * 4); - /* Wait for VAP to come to senses.. */ - /* there is no need to emit it multiple times, (only once before VAP is programmed, - but this optimization is for later */ - OUT_RING_REG(R300_VAP_PVS_WAITIDLE, 0); + /* VAP is very sensitive so we purge cache before we program it + * and we also flush its state before & after */ + BEGIN_RING(6); + OUT_RING(CP_PACKET0(R300_RB3D_DSTCACHE_CTLSTAT, 0)); + OUT_RING(R300_RB3D_DC_FLUSH); + OUT_RING(CP_PACKET0(RADEON_WAIT_UNTIL, 0)); + OUT_RING(RADEON_WAIT_3D_IDLECLEAN); + OUT_RING(CP_PACKET0(R300_VAP_PVS_STATE_FLUSH_REG, 0)); + OUT_RING(0); + ADVANCE_RING(); + /* set flush flag */ + dev_priv->track_flush |= RADEON_FLUSH_EMITED; + + BEGIN_RING(3 + sz * 4); OUT_RING_REG(R300_VAP_PVS_UPLOAD_ADDRESS, addr); OUT_RING(CP_PACKET0_TABLE(R300_VAP_PVS_UPLOAD_DATA, sz * 4 - 1)); OUT_RING_TABLE((int *)cmdbuf->buf, sz * 4); + ADVANCE_RING(); + BEGIN_RING(2); + OUT_RING(CP_PACKET0(R300_VAP_PVS_STATE_FLUSH_REG, 0)); + OUT_RING(0); ADVANCE_RING(); cmdbuf->buf += sz * 16; @@ -424,6 +452,15 @@ static __inline__ int r300_emit_clear(drm_radeon_private_t *dev_priv, OUT_RING_TABLE((int *)cmdbuf->buf, 8); ADVANCE_RING(); + BEGIN_RING(4); + OUT_RING(CP_PACKET0(R300_RB3D_DSTCACHE_CTLSTAT, 0)); + OUT_RING(R300_RB3D_DC_FLUSH); + OUT_RING(CP_PACKET0(RADEON_WAIT_UNTIL, 0)); + OUT_RING(RADEON_WAIT_3D_IDLECLEAN); + ADVANCE_RING(); + /* set flush flag */ + dev_priv->track_flush |= RADEON_FLUSH_EMITED; + cmdbuf->buf += 8 * 4; cmdbuf->bufsz -= 8 * 4; @@ -543,22 +580,23 @@ static __inline__ int r300_emit_bitblt_multi(drm_radeon_private_t *dev_priv, return 0; } -static __inline__ int r300_emit_indx_buffer(drm_radeon_private_t *dev_priv, - drm_radeon_kcmd_buffer_t *cmdbuf) +static __inline__ int r300_emit_draw_indx_2(drm_radeon_private_t *dev_priv, + drm_radeon_kcmd_buffer_t *cmdbuf) { - u32 *cmd = (u32 *) cmdbuf->buf; - int count, ret; + u32 *cmd; + int count; + int expected_count; RING_LOCALS; - count=(cmd[0]>>16) & 0x3fff; + cmd = (u32 *) cmdbuf->buf; + count = (cmd[0]>>16) & 0x3fff; + expected_count = cmd[1] >> 16; + if (!(cmd[1] & R300_VAP_VF_CNTL__INDEX_SIZE_32bit)) + expected_count = (expected_count+1)/2; - if ((cmd[1] & 0x8000ffff) != 0x80000810) { - DRM_ERROR("Invalid indx_buffer reg address %08X\n", cmd[1]); - return -EINVAL; - } - ret = !radeon_check_offset(dev_priv, cmd[2]); - if (ret) { - DRM_ERROR("Invalid indx_buffer offset is %08X\n", cmd[2]); + if (count && count != expected_count) { + DRM_ERROR("3D_DRAW_INDX_2: packet size %i, expected %i\n", + count, expected_count); return -EINVAL; } @@ -570,6 +608,50 @@ static __inline__ int r300_emit_indx_buffer(drm_radeon_private_t *dev_priv, cmdbuf->buf += (count+2)*4; cmdbuf->bufsz -= (count+2)*4; + if (!count) { + drm_r300_cmd_header_t header; + + if (cmdbuf->bufsz < 4*4 + sizeof(header)) { + DRM_ERROR("3D_DRAW_INDX_2: expect subsequent INDX_BUFFER, but stream is too short.\n"); + return -EINVAL; + } + + header.u = *(unsigned int *)cmdbuf->buf; + + cmdbuf->buf += sizeof(header); + cmdbuf->bufsz -= sizeof(header); + cmd = (u32 *) cmdbuf->buf; + + if (header.header.cmd_type != R300_CMD_PACKET3 || + header.packet3.packet != R300_CMD_PACKET3_RAW || + cmd[0] != CP_PACKET3(RADEON_CP_INDX_BUFFER, 2)) { + DRM_ERROR("3D_DRAW_INDX_2: expect subsequent INDX_BUFFER.\n"); + return -EINVAL; + } + + if ((cmd[1] & 0x8000ffff) != 0x80000810) { + DRM_ERROR("Invalid indx_buffer reg address %08X\n", cmd[1]); + return -EINVAL; + } + if (!radeon_check_offset(dev_priv, cmd[2])) { + DRM_ERROR("Invalid indx_buffer offset is %08X\n", cmd[2]); + return -EINVAL; + } + if (cmd[3] != expected_count) { + DRM_ERROR("INDX_BUFFER: buffer size %i, expected %i\n", + cmd[3], expected_count); + return -EINVAL; + } + + BEGIN_RING(4); + OUT_RING(cmd[0]); + OUT_RING_TABLE((int *)(cmdbuf->buf + 4), 3); + ADVANCE_RING(); + + cmdbuf->buf += 4*4; + cmdbuf->bufsz -= 4*4; + } + return 0; } @@ -613,11 +695,22 @@ static __inline__ int r300_emit_raw_packet3(drm_radeon_private_t *dev_priv, case RADEON_CNTL_BITBLT_MULTI: return r300_emit_bitblt_multi(dev_priv, cmdbuf); - case RADEON_CP_INDX_BUFFER: /* DRAW_INDX_2 without INDX_BUFFER seems to lock up the gpu */ - return r300_emit_indx_buffer(dev_priv, cmdbuf); - case RADEON_CP_3D_DRAW_IMMD_2: /* triggers drawing using in-packet vertex data */ - case RADEON_CP_3D_DRAW_VBUF_2: /* triggers drawing of vertex buffers setup elsewhere */ - case RADEON_CP_3D_DRAW_INDX_2: /* triggers drawing using indices to vertex buffer */ + case RADEON_CP_INDX_BUFFER: + DRM_ERROR("packet3 INDX_BUFFER without preceding 3D_DRAW_INDX_2 is illegal.\n"); + return -EINVAL; + case RADEON_CP_3D_DRAW_IMMD_2: + /* triggers drawing using in-packet vertex data */ + case RADEON_CP_3D_DRAW_VBUF_2: + /* triggers drawing of vertex buffers setup elsewhere */ + dev_priv->track_flush &= ~(RADEON_FLUSH_EMITED | + RADEON_PURGE_EMITED); + break; + case RADEON_CP_3D_DRAW_INDX_2: + /* triggers drawing using indices to vertex buffer */ + /* whenever we send vertex we clear flush & purge */ + dev_priv->track_flush &= ~(RADEON_FLUSH_EMITED | + RADEON_PURGE_EMITED); + return r300_emit_draw_indx_2(dev_priv, cmdbuf); case RADEON_WAIT_FOR_IDLE: case RADEON_CP_NOP: /* these packets are safe */ @@ -713,17 +806,53 @@ static __inline__ int r300_emit_packet3(drm_radeon_private_t *dev_priv, */ static __inline__ void r300_pacify(drm_radeon_private_t *dev_priv) { + uint32_t cache_z, cache_3d, cache_2d; RING_LOCALS; - BEGIN_RING(6); - OUT_RING(CP_PACKET0(R300_RB3D_DSTCACHE_CTLSTAT, 0)); - OUT_RING(R300_RB3D_DSTCACHE_UNKNOWN_0A); + cache_z = R300_ZC_FLUSH; + cache_2d = R300_RB2D_DC_FLUSH; + cache_3d = R300_RB3D_DC_FLUSH; + if (!(dev_priv->track_flush & RADEON_PURGE_EMITED)) { + /* we can purge, primitive where draw since last purge */ + cache_z |= R300_ZC_FREE; + cache_2d |= R300_RB2D_DC_FREE; + cache_3d |= R300_RB3D_DC_FREE; + } + + /* flush & purge zbuffer */ + BEGIN_RING(2); OUT_RING(CP_PACKET0(R300_ZB_ZCACHE_CTLSTAT, 0)); - OUT_RING(R300_ZB_ZCACHE_CTLSTAT_ZC_FLUSH_FLUSH_AND_FREE| - R300_ZB_ZCACHE_CTLSTAT_ZC_FREE_FREE); - OUT_RING(CP_PACKET3(RADEON_CP_NOP, 0)); - OUT_RING(0x0); + OUT_RING(cache_z); + ADVANCE_RING(); + /* flush & purge 3d */ + BEGIN_RING(2); + OUT_RING(CP_PACKET0(R300_RB3D_DSTCACHE_CTLSTAT, 0)); + OUT_RING(cache_3d); + ADVANCE_RING(); + /* flush & purge texture */ + BEGIN_RING(2); + OUT_RING(CP_PACKET0(R300_TX_INVALTAGS, 0)); + OUT_RING(0); + ADVANCE_RING(); + /* FIXME: is this one really needed ? */ + BEGIN_RING(2); + OUT_RING(CP_PACKET0(R300_RB3D_AARESOLVE_CTL, 0)); + OUT_RING(0); + ADVANCE_RING(); + BEGIN_RING(2); + OUT_RING(CP_PACKET0(RADEON_WAIT_UNTIL, 0)); + OUT_RING(RADEON_WAIT_3D_IDLECLEAN); + ADVANCE_RING(); + /* flush & purge 2d through E2 as RB2D will trigger lockup */ + BEGIN_RING(4); + OUT_RING(CP_PACKET0(R300_DSTCACHE_CTLSTAT, 0)); + OUT_RING(cache_2d); + OUT_RING(CP_PACKET0(RADEON_WAIT_UNTIL, 0)); + OUT_RING(RADEON_WAIT_2D_IDLECLEAN | + RADEON_WAIT_HOST_IDLECLEAN); ADVANCE_RING(); + /* set flush & purge flags */ + dev_priv->track_flush |= RADEON_FLUSH_EMITED | RADEON_PURGE_EMITED; } /** @@ -905,8 +1034,7 @@ int r300_do_cp_cmdbuf(struct drm_device *dev, DRM_DEBUG("\n"); - /* See the comment above r300_emit_begin3d for why this call must be here, - * and what the cleanup gotos are for. */ + /* pacify */ r300_pacify(dev_priv); if (cmdbuf->nbox <= R300_SIMULTANEOUS_CLIPRECTS) { |