summaryrefslogtreecommitdiff
path: root/drivers/input/touchscreen
diff options
context:
space:
mode:
Diffstat (limited to 'drivers/input/touchscreen')
-rw-r--r--drivers/input/touchscreen/Kconfig53
-rw-r--r--drivers/input/touchscreen/Makefile7
-rw-r--r--drivers/input/touchscreen/ads7846.c22
-rw-r--r--drivers/input/touchscreen/corgi_ts.c2
-rw-r--r--drivers/input/touchscreen/jornada720_ts.c4
-rw-r--r--drivers/input/touchscreen/mainstone-wm97xx.c302
-rw-r--r--drivers/input/touchscreen/ucb1400_ts.c4
-rw-r--r--drivers/input/touchscreen/usbtouchscreen.c31
-rw-r--r--drivers/input/touchscreen/wm9705.c353
-rw-r--r--drivers/input/touchscreen/wm9712.c462
-rw-r--r--drivers/input/touchscreen/wm9713.c460
-rw-r--r--drivers/input/touchscreen/wm97xx-core.c829
12 files changed, 2501 insertions, 28 deletions
diff --git a/drivers/input/touchscreen/Kconfig b/drivers/input/touchscreen/Kconfig
index 90e8e92dfe47..565ec711c2ee 100644
--- a/drivers/input/touchscreen/Kconfig
+++ b/drivers/input/touchscreen/Kconfig
@@ -185,6 +185,59 @@ config TOUCHSCREEN_UCB1400
To compile this driver as a module, choose M here: the
module will be called ucb1400_ts.
+config TOUCHSCREEN_WM97XX
+ tristate "Support for WM97xx AC97 touchscreen controllers"
+ depends on AC97_BUS
+ help
+ Say Y here if you have a Wolfson Microelectronics WM97xx
+ touchscreen connected to your system. Note that this option
+ only enables core driver, you will also need to select
+ support for appropriate chip below.
+
+ If unsure, say N.
+
+ To compile this driver as a module, choose M here: the
+ module will be called wm97xx-ts.
+
+config TOUCHSCREEN_WM9705
+ bool "WM9705 Touchscreen interface support"
+ depends on TOUCHSCREEN_WM97XX
+ help
+ Say Y here if you have a Wolfson Microelectronics WM9705
+ touchscreen controller connected to your system.
+
+ If unsure, say N.
+
+config TOUCHSCREEN_WM9712
+ bool "WM9712 Touchscreen interface support"
+ depends on TOUCHSCREEN_WM97XX
+ help
+ Say Y here if you have a Wolfson Microelectronics WM9712
+ touchscreen controller connected to your system.
+
+ If unsure, say N.
+
+config TOUCHSCREEN_WM9713
+ bool "WM9713 Touchscreen interface support"
+ depends on TOUCHSCREEN_WM97XX
+ help
+ Say Y here if you have a Wolfson Microelectronics WM9713 touchscreen
+ controller connected to your system.
+
+ If unsure, say N.
+
+config TOUCHSCREEN_WM97XX_MAINSTONE
+ tristate "WM97xx Mainstone accelerated touch"
+ depends on TOUCHSCREEN_WM97XX && ARCH_PXA
+ help
+ Say Y here for support for streaming mode with WM97xx touchscreens
+ on Mainstone systems.
+
+ If unsure, say N.
+
+ To compile this driver as a module, choose M here: the
+ module will be called mainstone-wm97xx.
+
config TOUCHSCREEN_USB_COMPOSITE
tristate "USB Touchscreen Driver"
depends on USB_ARCH_HAS_HCD
diff --git a/drivers/input/touchscreen/Makefile b/drivers/input/touchscreen/Makefile
index 35d4097df35a..3c096d75651d 100644
--- a/drivers/input/touchscreen/Makefile
+++ b/drivers/input/touchscreen/Makefile
@@ -4,6 +4,8 @@
# Each configuration option enables a list of files.
+wm97xx-ts-y := wm97xx-core.o
+
obj-$(CONFIG_TOUCHSCREEN_ADS7846) += ads7846.o
obj-$(CONFIG_TOUCHSCREEN_BITSY) += h3600_ts_input.o
obj-$(CONFIG_TOUCHSCREEN_CORGI) += corgi_ts.o
@@ -19,3 +21,8 @@ obj-$(CONFIG_TOUCHSCREEN_PENMOUNT) += penmount.o
obj-$(CONFIG_TOUCHSCREEN_TOUCHRIGHT) += touchright.o
obj-$(CONFIG_TOUCHSCREEN_TOUCHWIN) += touchwin.o
obj-$(CONFIG_TOUCHSCREEN_UCB1400) += ucb1400_ts.o
+obj-$(CONFIG_TOUCHSCREEN_WM97XX) += wm97xx-ts.o
+wm97xx-ts-$(CONFIG_TOUCHSCREEN_WM9705) += wm9705.o
+wm97xx-ts-$(CONFIG_TOUCHSCREEN_WM9712) += wm9712.o
+wm97xx-ts-$(CONFIG_TOUCHSCREEN_WM9713) += wm9713.o
+obj-$(CONFIG_TOUCHSCREEN_WM97XX_MAINSTONE) += mainstone-wm97xx.o
diff --git a/drivers/input/touchscreen/ads7846.c b/drivers/input/touchscreen/ads7846.c
index 39573b91c8de..907a45fe9d40 100644
--- a/drivers/input/touchscreen/ads7846.c
+++ b/drivers/input/touchscreen/ads7846.c
@@ -80,6 +80,7 @@ struct ads7846 {
#endif
u16 model;
+ u16 vref_mv;
u16 vref_delay_usecs;
u16 x_plate_ohms;
u16 pressure_max;
@@ -177,9 +178,6 @@ struct ads7846 {
* The range is GND..vREF. The ads7843 and ads7835 must use external vREF;
* ads7846 lets that pin be unconnected, to use internal vREF.
*/
-static unsigned vREF_mV;
-module_param(vREF_mV, uint, 0);
-MODULE_PARM_DESC(vREF_mV, "external vREF voltage, in milliVolts");
struct ser_req {
u8 ref_on;
@@ -206,7 +204,6 @@ static int ads7846_read12_ser(struct device *dev, unsigned command)
struct ads7846 *ts = dev_get_drvdata(dev);
struct ser_req *req = kzalloc(sizeof *req, GFP_KERNEL);
int status;
- int uninitialized_var(sample);
int use_internal;
if (!req)
@@ -263,13 +260,13 @@ static int ads7846_read12_ser(struct device *dev, unsigned command)
if (status == 0) {
/* on-wire is a must-ignore bit, a BE12 value, then padding */
- sample = be16_to_cpu(req->sample);
- sample = sample >> 3;
- sample &= 0x0fff;
+ status = be16_to_cpu(req->sample);
+ status = status >> 3;
+ status &= 0x0fff;
}
kfree(req);
- return status ? status : sample;
+ return status;
}
#if defined(CONFIG_HWMON) || defined(CONFIG_HWMON_MODULE)
@@ -310,7 +307,7 @@ static inline unsigned vaux_adjust(struct ads7846 *ts, ssize_t v)
unsigned retval = v;
/* external resistors may scale vAUX into 0..vREF */
- retval *= vREF_mV;
+ retval *= ts->vref_mv;
retval = retval >> 12;
return retval;
}
@@ -368,14 +365,14 @@ static int ads784x_hwmon_register(struct spi_device *spi, struct ads7846 *ts)
/* hwmon sensors need a reference voltage */
switch (ts->model) {
case 7846:
- if (!vREF_mV) {
+ if (!ts->vref_mv) {
dev_dbg(&spi->dev, "assuming 2.5V internal vREF\n");
- vREF_mV = 2500;
+ ts->vref_mv = 2500;
}
break;
case 7845:
case 7843:
- if (!vREF_mV) {
+ if (!ts->vref_mv) {
dev_warn(&spi->dev,
"external vREF for ADS%d not specified\n",
ts->model);
@@ -868,6 +865,7 @@ static int __devinit ads7846_probe(struct spi_device *spi)
ts->spi = spi;
ts->input = input_dev;
+ ts->vref_mv = pdata->vref_mv;
hrtimer_init(&ts->timer, CLOCK_MONOTONIC, HRTIMER_MODE_REL);
ts->timer.function = ads7846_timer;
diff --git a/drivers/input/touchscreen/corgi_ts.c b/drivers/input/touchscreen/corgi_ts.c
index a22576779acd..4e9d8eece2e0 100644
--- a/drivers/input/touchscreen/corgi_ts.c
+++ b/drivers/input/touchscreen/corgi_ts.c
@@ -362,6 +362,7 @@ static struct platform_driver corgits_driver = {
.resume = corgits_resume,
.driver = {
.name = "corgi-ts",
+ .owner = THIS_MODULE,
},
};
@@ -381,3 +382,4 @@ module_exit(corgits_exit);
MODULE_AUTHOR("Richard Purdie <rpurdie@rpsys.net>");
MODULE_DESCRIPTION("Corgi TouchScreen Driver");
MODULE_LICENSE("GPL");
+MODULE_ALIAS("platform:corgi-ts");
diff --git a/drivers/input/touchscreen/jornada720_ts.c b/drivers/input/touchscreen/jornada720_ts.c
index 42a1c9a1940e..742242111bf1 100644
--- a/drivers/input/touchscreen/jornada720_ts.c
+++ b/drivers/input/touchscreen/jornada720_ts.c
@@ -160,11 +160,15 @@ static int __devexit jornada720_ts_remove(struct platform_device *pdev)
return 0;
}
+/* work with hotplug and coldplug */
+MODULE_ALIAS("platform:jornada_ts");
+
static struct platform_driver jornada720_ts_driver = {
.probe = jornada720_ts_probe,
.remove = __devexit_p(jornada720_ts_remove),
.driver = {
.name = "jornada_ts",
+ .owner = THIS_MODULE,
},
};
diff --git a/drivers/input/touchscreen/mainstone-wm97xx.c b/drivers/input/touchscreen/mainstone-wm97xx.c
new file mode 100644
index 000000000000..a79f029b91c0
--- /dev/null
+++ b/drivers/input/touchscreen/mainstone-wm97xx.c
@@ -0,0 +1,302 @@
+/*
+ * mainstone-wm97xx.c -- Mainstone Continuous Touch screen driver for
+ * Wolfson WM97xx AC97 Codecs.
+ *
+ * Copyright 2004, 2007 Wolfson Microelectronics PLC.
+ * Author: Liam Girdwood
+ * liam.girdwood@wolfsonmicro.com or linux@wolfsonmicro.com
+ * Parts Copyright : Ian Molton <spyro@f2s.com>
+ * Andrew Zabolotny <zap@homelink.ru>
+ *
+ * This program is free software; you can redistribute it and/or modify it
+ * under the terms of the GNU General Public License as published by the
+ * Free Software Foundation; either version 2 of the License, or (at your
+ * option) any later version.
+ *
+ * Notes:
+ * This is a wm97xx extended touch driver to capture touch
+ * data in a continuous manner on the Intel XScale archictecture
+ *
+ * Features:
+ * - codecs supported:- WM9705, WM9712, WM9713
+ * - processors supported:- Intel XScale PXA25x, PXA26x, PXA27x
+ *
+ */
+
+#include <linux/module.h>
+#include <linux/moduleparam.h>
+#include <linux/version.h>
+#include <linux/kernel.h>
+#include <linux/init.h>
+#include <linux/delay.h>
+#include <linux/irq.h>
+#include <linux/interrupt.h>
+#include <linux/wm97xx.h>
+#include <linux/io.h>
+#include <asm/arch/pxa-regs.h>
+
+#define VERSION "0.13"
+
+struct continuous {
+ u16 id; /* codec id */
+ u8 code; /* continuous code */
+ u8 reads; /* number of coord reads per read cycle */
+ u32 speed; /* number of coords per second */
+};
+
+#define WM_READS(sp) ((sp / HZ) + 1)
+
+static const struct continuous cinfo[] = {
+ {WM9705_ID2, 0, WM_READS(94), 94},
+ {WM9705_ID2, 1, WM_READS(188), 188},
+ {WM9705_ID2, 2, WM_READS(375), 375},
+ {WM9705_ID2, 3, WM_READS(750), 750},
+ {WM9712_ID2, 0, WM_READS(94), 94},
+ {WM9712_ID2, 1, WM_READS(188), 188},
+ {WM9712_ID2, 2, WM_READS(375), 375},
+ {WM9712_ID2, 3, WM_READS(750), 750},
+ {WM9713_ID2, 0, WM_READS(94), 94},
+ {WM9713_ID2, 1, WM_READS(120), 120},
+ {WM9713_ID2, 2, WM_READS(154), 154},
+ {WM9713_ID2, 3, WM_READS(188), 188},
+};
+
+/* continuous speed index */
+static int sp_idx;
+static u16 last, tries;
+
+/*
+ * Pen sampling frequency (Hz) in continuous mode.
+ */
+static int cont_rate = 200;
+module_param(cont_rate, int, 0);
+MODULE_PARM_DESC(cont_rate, "Sampling rate in continuous mode (Hz)");
+
+/*
+ * Pen down detection.
+ *
+ * This driver can either poll or use an interrupt to indicate a pen down
+ * event. If the irq request fails then it will fall back to polling mode.
+ */
+static int pen_int;
+module_param(pen_int, int, 0);
+MODULE_PARM_DESC(pen_int, "Pen down detection (1 = interrupt, 0 = polling)");
+
+/*
+ * Pressure readback.
+ *
+ * Set to 1 to read back pen down pressure
+ */
+static int pressure;
+module_param(pressure, int, 0);
+MODULE_PARM_DESC(pressure, "Pressure readback (1 = pressure, 0 = no pressure)");
+
+/*
+ * AC97 touch data slot.
+ *
+ * Touch screen readback data ac97 slot
+ */
+static int ac97_touch_slot = 5;
+module_param(ac97_touch_slot, int, 0);
+MODULE_PARM_DESC(ac97_touch_slot, "Touch screen data slot AC97 number");
+
+
+/* flush AC97 slot 5 FIFO on pxa machines */
+#ifdef CONFIG_PXA27x
+static void wm97xx_acc_pen_up(struct wm97xx *wm)
+{
+ schedule_timeout_uninterruptible(1);
+
+ while (MISR & (1 << 2))
+ MODR;
+}
+#else
+static void wm97xx_acc_pen_up(struct wm97xx *wm)
+{
+ int count = 16;
+ schedule_timeout_uninterruptible(1);
+
+ while (count < 16) {
+ MODR;
+ count--;
+ }
+}
+#endif
+
+static int wm97xx_acc_pen_down(struct wm97xx *wm)
+{
+ u16 x, y, p = 0x100 | WM97XX_ADCSEL_PRES;
+ int reads = 0;
+
+ /* When the AC97 queue has been drained we need to allow time
+ * to buffer up samples otherwise we end up spinning polling
+ * for samples. The controller can't have a suitably low
+ * threashold set to use the notifications it gives.
+ */
+ schedule_timeout_uninterruptible(1);
+
+ if (tries > 5) {
+ tries = 0;
+ return RC_PENUP;
+ }
+
+ x = MODR;
+ if (x == last) {
+ tries++;
+ return RC_AGAIN;
+ }
+ last = x;
+ do {
+ if (reads)
+ x = MODR;
+ y = MODR;
+ if (pressure)
+ p = MODR;
+
+ /* are samples valid */
+ if ((x & WM97XX_ADCSRC_MASK) != WM97XX_ADCSEL_X ||
+ (y & WM97XX_ADCSRC_MASK) != WM97XX_ADCSEL_Y ||
+ (p & WM97XX_ADCSRC_MASK) != WM97XX_ADCSEL_PRES)
+ goto up;
+
+ /* coordinate is good */
+ tries = 0;
+ input_report_abs(wm->input_dev, ABS_X, x & 0xfff);
+ input_report_abs(wm->input_dev, ABS_Y, y & 0xfff);
+ input_report_abs(wm->input_dev, ABS_PRESSURE, p & 0xfff);
+ input_sync(wm->input_dev);
+ reads++;
+ } while (reads < cinfo[sp_idx].reads);
+up:
+ return RC_PENDOWN | RC_AGAIN;
+}
+
+static int wm97xx_acc_startup(struct wm97xx *wm)
+{
+ int idx = 0;
+
+ /* check we have a codec */
+ if (wm->ac97 == NULL)
+ return -ENODEV;
+
+ /* Go you big red fire engine */
+ for (idx = 0; idx < ARRAY_SIZE(cinfo); idx++) {
+ if (wm->id != cinfo[idx].id)
+ continue;
+ sp_idx = idx;
+ if (cont_rate <= cinfo[idx].speed)
+ break;
+ }
+ wm->acc_rate = cinfo[sp_idx].code;
+ wm->acc_slot = ac97_touch_slot;
+ dev_info(wm->dev,
+ "mainstone accelerated touchscreen driver, %d samples/sec\n",
+ cinfo[sp_idx].speed);
+
+ /* codec specific irq config */
+ if (pen_int) {
+ switch (wm->id) {
+ case WM9705_ID2:
+ wm->pen_irq = IRQ_GPIO(4);
+ set_irq_type(IRQ_GPIO(4), IRQT_BOTHEDGE);
+ break;
+ case WM9712_ID2:
+ case WM9713_ID2:
+ /* enable pen down interrupt */
+ /* use PEN_DOWN GPIO 13 to assert IRQ on GPIO line 2 */
+ wm->pen_irq = MAINSTONE_AC97_IRQ;
+ wm97xx_config_gpio(wm, WM97XX_GPIO_13, WM97XX_GPIO_IN,
+ WM97XX_GPIO_POL_HIGH,
+ WM97XX_GPIO_STICKY,
+ WM97XX_GPIO_WAKE);
+ wm97xx_config_gpio(wm, WM97XX_GPIO_2, WM97XX_GPIO_OUT,
+ WM97XX_GPIO_POL_HIGH,
+ WM97XX_GPIO_NOTSTICKY,
+ WM97XX_GPIO_NOWAKE);
+ break;
+ default:
+ dev_err(wm->dev,
+ "pen down irq not supported on this device\n");
+ pen_int = 0;
+ break;
+ }
+ }
+
+ return 0;
+}
+
+static void wm97xx_acc_shutdown(struct wm97xx *wm)
+{
+ /* codec specific deconfig */
+ if (pen_int) {
+ switch (wm->id & 0xffff) {
+ case WM9705_ID2:
+ wm->pen_irq = 0;
+ break;
+ case WM9712_ID2:
+ case WM9713_ID2:
+ /* disable interrupt */
+ wm->pen_irq = 0;
+ break;
+ }
+ }
+}
+
+static void wm97xx_irq_enable(struct wm97xx *wm, int enable)
+{
+ if (enable)
+ enable_irq(wm->pen_irq);
+ else
+ disable_irq(wm->pen_irq);
+}
+
+static struct wm97xx_mach_ops mainstone_mach_ops = {
+ .acc_enabled = 1,
+ .acc_pen_up = wm97xx_acc_pen_up,
+ .acc_pen_down = wm97xx_acc_pen_down,
+ .acc_startup = wm97xx_acc_startup,
+ .acc_shutdown = wm97xx_acc_shutdown,
+ .irq_enable = wm97xx_irq_enable,
+ .irq_gpio = WM97XX_GPIO_2,
+};
+
+static int mainstone_wm97xx_probe(struct platform_device *pdev)
+{
+ struct wm97xx *wm = platform_get_drvdata(pdev);
+
+ return wm97xx_register_mach_ops(wm, &mainstone_mach_ops);
+}
+
+static int mainstone_wm97xx_remove(struct platform_device *pdev)
+{
+ struct wm97xx *wm = platform_get_drvdata(pdev);
+
+ wm97xx_unregister_mach_ops(wm);
+ return 0;
+}
+
+static struct platform_driver mainstone_wm97xx_driver = {
+ .probe = mainstone_wm97xx_probe,
+ .remove = mainstone_wm97xx_remove,
+ .driver = {
+ .name = "wm97xx-touch",
+ },
+};
+
+static int __init mainstone_wm97xx_init(void)
+{
+ return platform_driver_register(&mainstone_wm97xx_driver);
+}
+
+static void __exit mainstone_wm97xx_exit(void)
+{
+ platform_driver_unregister(&mainstone_wm97xx_driver);
+}
+
+module_init(mainstone_wm97xx_init);
+module_exit(mainstone_wm97xx_exit);
+
+/* Module information */
+MODULE_AUTHOR("Liam Girdwood <liam.girdwood@wolfsonmicro.com>");
+MODULE_DESCRIPTION("wm97xx continuous touch driver for mainstone");
+MODULE_LICENSE("GPL");
diff --git a/drivers/input/touchscreen/ucb1400_ts.c b/drivers/input/touchscreen/ucb1400_ts.c
index 607f9933aa1f..bce018e45bce 100644
--- a/drivers/input/touchscreen/ucb1400_ts.c
+++ b/drivers/input/touchscreen/ucb1400_ts.c
@@ -427,10 +427,6 @@ static int ucb1400_detect_irq(struct ucb1400 *ucb)
unsigned long mask, timeout;
mask = probe_irq_on();
- if (!mask) {
- probe_irq_off(mask);
- return -EBUSY;
- }
/* Enable the ADC interrupt. */
ucb1400_reg_write(ucb, UCB_IE_RIS, UCB_IE_ADC);
diff --git a/drivers/input/touchscreen/usbtouchscreen.c b/drivers/input/touchscreen/usbtouchscreen.c
index 63f9664a066f..3a0a8ca57076 100644
--- a/drivers/input/touchscreen/usbtouchscreen.c
+++ b/drivers/input/touchscreen/usbtouchscreen.c
@@ -396,9 +396,12 @@ static int gunze_read_data(struct usbtouch_usb *dev, unsigned char *pkt)
static int dmc_tsc10_init(struct usbtouch_usb *usbtouch)
{
struct usb_device *dev = usbtouch->udev;
- int ret;
- unsigned char buf[2];
+ int ret = -ENOMEM;
+ unsigned char *buf;
+ buf = kmalloc(2, GFP_KERNEL);
+ if (!buf)
+ goto err_nobuf;
/* reset */
buf[0] = buf[1] = 0xFF;
ret = usb_control_msg(dev, usb_rcvctrlpipe (dev, 0),
@@ -406,9 +409,11 @@ static int dmc_tsc10_init(struct usbtouch_usb *usbtouch)
USB_DIR_IN | USB_TYPE_VENDOR | USB_RECIP_DEVICE,
0, 0, buf, 2, USB_CTRL_SET_TIMEOUT);
if (ret < 0)
- return ret;
- if (buf[0] != 0x06 || buf[1] != 0x00)
- return -ENODEV;
+ goto err_out;
+ if (buf[0] != 0x06 || buf[1] != 0x00) {
+ ret = -ENODEV;
+ goto err_out;
+ }
/* set coordinate output rate */
buf[0] = buf[1] = 0xFF;
@@ -417,20 +422,22 @@ static int dmc_tsc10_init(struct usbtouch_usb *usbtouch)
USB_DIR_IN | USB_TYPE_VENDOR | USB_RECIP_DEVICE,
TSC10_RATE_150, 0, buf, 2, USB_CTRL_SET_TIMEOUT);
if (ret < 0)
- return ret;
+ goto err_out;
if ((buf[0] != 0x06 || buf[1] != 0x00) &&
- (buf[0] != 0x15 || buf[1] != 0x01))
- return -ENODEV;
+ (buf[0] != 0x15 || buf[1] != 0x01)) {
+ ret = -ENODEV;
+ goto err_out;
+ }
/* start sending data */
ret = usb_control_msg(dev, usb_rcvctrlpipe (dev, 0),
TSC10_CMD_DATA1,
USB_DIR_OUT | USB_TYPE_VENDOR | USB_RECIP_DEVICE,
0, 0, NULL, 0, USB_CTRL_SET_TIMEOUT);
- if (ret < 0)
- return ret;
-
- return 0;
+err_out:
+ kfree(buf);
+err_nobuf:
+ return ret;
}
diff --git a/drivers/input/touchscreen/wm9705.c b/drivers/input/touchscreen/wm9705.c
new file mode 100644
index 000000000000..978e1a13ffc7
--- /dev/null
+++ b/drivers/input/touchscreen/wm9705.c
@@ -0,0 +1,353 @@
+/*
+ * wm9705.c -- Codec driver for Wolfson WM9705 AC97 Codec.
+ *
+ * Copyright 2003, 2004, 2005, 2006, 2007 Wolfson Microelectronics PLC.
+ * Author: Liam Girdwood
+ * liam.girdwood@wolfsonmicro.com or linux@wolfsonmicro.com
+ * Parts Copyright : Ian Molton <spyro@f2s.com>
+ * Andrew Zabolotny <zap@homelink.ru>
+ * Russell King <rmk@arm.linux.org.uk>
+ *
+ * This program is free software; you can redistribute it and/or modify it
+ * under the terms of the GNU General Public License as published by the
+ * Free Software Foundation; either version 2 of the License, or (at your
+ * option) any later version.
+ *
+ */
+
+#include <linux/module.h>
+#include <linux/moduleparam.h>
+#include <linux/version.h>
+#include <linux/kernel.h>
+#include <linux/input.h>
+#include <linux/delay.h>
+#include <linux/bitops.h>
+#include <linux/wm97xx.h>
+
+#define TS_NAME "wm97xx"
+#define WM9705_VERSION "1.00"
+#define DEFAULT_PRESSURE 0xb0c0
+
+/*
+ * Module parameters
+ */
+
+/*
+ * Set current used for pressure measurement.
+ *
+ * Set pil = 2 to use 400uA
+ * pil = 1 to use 200uA and
+ * pil = 0 to disable pressure measurement.
+ *
+ * This is used to increase the range of values returned by the adc
+ * when measureing touchpanel pressure.
+ */
+static int pil;
+module_param(pil, int, 0);
+MODULE_PARM_DESC(pil, "Set current used for pressure measurement.");
+
+/*
+ * Set threshold for pressure measurement.
+ *
+ * Pen down pressure below threshold is ignored.
+ */
+static int pressure = DEFAULT_PRESSURE & 0xfff;
+module_param(pressure, int, 0);
+MODULE_PARM_DESC(pressure, "Set threshold for pressure measurement.");
+
+/*
+ * Set adc sample delay.
+ *
+ * For accurate touchpanel measurements, some settling time may be
+ * required between the switch matrix applying a voltage across the
+ * touchpanel plate and the ADC sampling the signal.
+ *
+ * This delay can be set by setting delay = n, where n is the array
+ * position of the delay in the array delay_table below.
+ * Long delays > 1ms are supported for completeness, but are not
+ * recommended.
+ */
+static int delay = 4;
+module_param(delay, int, 0);
+MODULE_PARM_DESC(delay, "Set adc sample delay.");
+
+/*
+ * Pen detect comparator threshold.
+ *
+ * 0 to Vmid in 15 steps, 0 = use zero power comparator with Vmid threshold
+ * i.e. 1 = Vmid/15 threshold
+ * 15 = Vmid/1 threshold
+ *
+ * Adjust this value if you are having problems with pen detect not
+ * detecting any down events.
+ */
+static int pdd = 8;
+module_param(pdd, int, 0);
+MODULE_PARM_DESC(pdd, "Set pen detect comparator threshold");
+
+/*
+ * Set adc mask function.
+ *
+ * Sources of glitch noise, such as signals driving an LCD display, may feed
+ * through to the touch screen plates and affect measurement accuracy. In
+ * order to minimise this, a signal may be applied to the MASK pin to delay or
+ * synchronise the sampling.
+ *
+ * 0 = No delay or sync
+ * 1 = High on pin stops conversions
+ * 2 = Edge triggered, edge on pin delays conversion by delay param (above)
+ * 3 = Edge triggered, edge on pin starts conversion after delay param
+ */
+static int mask;
+module_param(mask, int, 0);
+MODULE_PARM_DESC(mask, "Set adc mask function.");
+
+/*
+ * ADC sample delay times in uS
+ */
+static const int delay_table[] = {
+ 21, /* 1 AC97 Link frames */
+ 42, /* 2 */
+ 84, /* 4 */
+ 167, /* 8 */
+ 333, /* 16 */
+ 667, /* 32 */
+ 1000, /* 48 */
+ 1333, /* 64 */
+ 2000, /* 96 */
+ 2667, /* 128 */
+ 3333, /* 160 */
+ 4000, /* 192 */
+ 4667, /* 224 */
+ 5333, /* 256 */
+ 6000, /* 288 */
+ 0 /* No delay, switch matrix always on */
+};
+
+/*
+ * Delay after issuing a POLL command.
+ *
+ * The delay is 3 AC97 link frames + the touchpanel settling delay
+ */
+static inline void poll_delay(int d)
+{
+ udelay(3 * AC97_LINK_FRAME + delay_table[d]);
+}
+
+/*
+ * set up the physical settings of the WM9705
+ */
+static void wm9705_phy_init(struct wm97xx *wm)
+{
+ u16 dig1 = 0, dig2 = WM97XX_RPR;
+
+ /*
+ * mute VIDEO and AUX as they share X and Y touchscreen
+ * inputs on the WM9705
+ */
+ wm97xx_reg_write(wm, AC97_AUX, 0x8000);
+ wm97xx_reg_write(wm, AC97_VIDEO, 0x8000);
+
+ /* touchpanel pressure current*/
+ if (pil == 2) {
+ dig2 |= WM9705_PIL;
+ dev_dbg(wm->dev,
+ "setting pressure measurement current to 400uA.");
+ } else if (pil)
+ dev_dbg(wm->dev,
+ "setting pressure measurement current to 200uA.");
+ if (!pil)
+ pressure = 0;
+
+ /* polling mode sample settling delay */
+ if (delay != 4) {
+ if (delay < 0 || delay > 15) {
+ dev_dbg(wm->dev, "supplied delay out of range.");
+ delay = 4;
+ }
+ }
+ dig1 &= 0xff0f;
+ dig1 |= WM97XX_DELAY(delay);
+ dev_dbg(wm->dev, "setting adc sample delay to %d u Secs.",
+ delay_table[delay]);
+
+ /* WM9705 pdd */
+ dig2 |= (pdd & 0x000f);
+ dev_dbg(wm->dev, "setting pdd to Vmid/%d", 1 - (pdd & 0x000f));
+
+ /* mask */
+ dig2 |= ((mask & 0x3) << 4);
+
+ wm97xx_reg_write(wm, AC97_WM97XX_DIGITISER1, dig1);
+ wm97xx_reg_write(wm, AC97_WM97XX_DIGITISER2, dig2);
+}
+
+static void wm9705_dig_enable(struct wm97xx *wm, int enable)
+{
+ if (enable) {
+ wm97xx_reg_write(wm, AC97_WM97XX_DIGITISER2,
+ wm->dig[2] | WM97XX_PRP_DET_DIG);
+ wm97xx_reg_read(wm, AC97_WM97XX_DIGITISER_RD); /* dummy read */
+ } else
+ wm97xx_reg_write(wm, AC97_WM97XX_DIGITISER2,
+ wm->dig[2] & ~WM97XX_PRP_DET_DIG);
+}
+
+static void wm9705_aux_prepare(struct wm97xx *wm)
+{
+ memcpy(wm->dig_save, wm->dig, sizeof(wm->dig));
+ wm97xx_reg_write(wm, AC97_WM97XX_DIGITISER1, 0);
+ wm97xx_reg_write(wm, AC97_WM97XX_DIGITISER2, WM97XX_PRP_DET_DIG);
+}
+
+static void wm9705_dig_restore(struct wm97xx *wm)
+{
+ wm97xx_reg_write(wm, AC97_WM97XX_DIGITISER1, wm->dig_save[1]);
+ wm97xx_reg_write(wm, AC97_WM97XX_DIGITISER2, wm->dig_save[2]);
+}
+
+static inline int is_pden(struct wm97xx *wm)
+{
+ return wm->dig[2] & WM9705_PDEN;
+}
+
+/*
+ * Read a sample from the WM9705 adc in polling mode.
+ */
+static int wm9705_poll_sample(struct wm97xx *wm, int adcsel, int *sample)
+{
+ int timeout = 5 * delay;
+
+ if (!wm->pen_probably_down) {
+ u16 data = wm97xx_reg_read(wm, AC97_WM97XX_DIGITISER_RD);
+ if (!(data & WM97XX_PEN_DOWN))
+ return RC_PENUP;
+ wm->pen_probably_down = 1;
+ }
+
+ /* set up digitiser */
+ if (adcsel & 0x8000)
+ adcsel = ((adcsel & 0x7fff) + 3) << 12;
+
+ if (wm->mach_ops && wm->mach_ops->pre_sample)
+ wm->mach_ops->pre_sample(adcsel);
+ wm97xx_reg_write(wm, AC97_WM97XX_DIGITISER1,
+ adcsel | WM97XX_POLL | WM97XX_DELAY(delay));
+
+ /* wait 3 AC97 time slots + delay for conversion */
+ poll_delay(delay);
+
+ /* wait for POLL to go low */
+ while ((wm97xx_reg_read(wm, AC97_WM97XX_DIGITISER1) & WM97XX_POLL)
+ && timeout) {
+ udelay(AC97_LINK_FRAME);
+ timeout--;
+ }
+
+ if (timeout == 0) {
+ /* If PDEN is set, we can get a timeout when pen goes up */
+ if (is_pden(wm))
+ wm->pen_probably_down = 0;
+ else
+ dev_dbg(wm->dev, "adc sample timeout");
+ return RC_PENUP;
+ }
+
+ *sample = wm97xx_reg_read(wm, AC97_WM97XX_DIGITISER_RD);
+ if (wm->mach_ops && wm->mach_ops->post_sample)
+ wm->mach_ops->post_sample(adcsel);
+
+ /* check we have correct sample */
+ if ((*sample & WM97XX_ADCSEL_MASK) != adcsel) {
+ dev_dbg(wm->dev, "adc wrong sample, read %x got %x", adcsel,
+ *sample & WM97XX_ADCSEL_MASK);
+ return RC_PENUP;
+ }
+
+ if (!(*sample & WM97XX_PEN_DOWN)) {
+ wm->pen_probably_down = 0;
+ return RC_PENUP;
+ }
+
+ return RC_VALID;
+}
+
+/*
+ * Sample the WM9705 touchscreen in polling mode
+ */
+static int wm9705_poll_touch(struct wm97xx *wm, struct wm97xx_data *data)
+{
+ int rc;
+
+ rc = wm9705_poll_sample(wm, WM97XX_ADCSEL_X, &data->x);
+ if (rc != RC_VALID)
+ return rc;
+ rc = wm9705_poll_sample(wm, WM97XX_ADCSEL_Y, &data->y);
+ if (rc != RC_VALID)
+ return rc;
+ if (pil) {
+ rc = wm9705_poll_sample(wm, WM97XX_ADCSEL_PRES, &data->p);
+ if (rc != RC_VALID)
+ return rc;
+ } else
+ data->p = DEFAULT_PRESSURE;
+
+ return RC_VALID;
+}
+
+/*
+ * Enable WM9705 continuous mode, i.e. touch data is streamed across
+ * an AC97 slot
+ */
+static int wm9705_acc_enable(struct wm97xx *wm, int enable)
+{
+ u16 dig1, dig2;
+ int ret = 0;
+
+ dig1 = wm->dig[1];
+ dig2 = wm->dig[2];
+
+ if (enable) {
+ /* continous mode */
+ if (wm->mach_ops->acc_startup &&
+ (ret = wm->mach_ops->acc_startup(wm)) < 0)
+ return ret;
+ dig1 &= ~(WM97XX_CM_RATE_MASK | WM97XX_ADCSEL_MASK |
+ WM97XX_DELAY_MASK | WM97XX_SLT_MASK);
+ dig1 |= WM97XX_CTC | WM97XX_COO | WM97XX_SLEN |
+ WM97XX_DELAY(delay) |
+ WM97XX_SLT(wm->acc_slot) |
+ WM97XX_RATE(wm->acc_rate);
+ if (pil)
+ dig1 |= WM97XX_ADCSEL_PRES;
+ dig2 |= WM9705_PDEN;
+ } else {
+ dig1 &= ~(WM97XX_CTC | WM97XX_COO | WM97XX_SLEN);
+ dig2 &= ~WM9705_PDEN;
+ if (wm->mach_ops->acc_shutdown)
+ wm->mach_ops->acc_shutdown(wm);
+ }
+
+ wm97xx_reg_write(wm, AC97_WM97XX_DIGITISER1, dig1);
+ wm97xx_reg_write(wm, AC97_WM97XX_DIGITISER2, dig2);
+
+ return ret;
+}
+
+struct wm97xx_codec_drv wm9705_codec = {
+ .id = WM9705_ID2,
+ .name = "wm9705",
+ .poll_sample = wm9705_poll_sample,
+ .poll_touch = wm9705_poll_touch,
+ .acc_enable = wm9705_acc_enable,
+ .phy_init = wm9705_phy_init,
+ .dig_enable = wm9705_dig_enable,
+ .dig_restore = wm9705_dig_restore,
+ .aux_prepare = wm9705_aux_prepare,
+};
+EXPORT_SYMBOL_GPL(wm9705_codec);
+
+/* Module information */
+MODULE_AUTHOR("Liam Girdwood <liam.girdwood@wolfsonmicro.com>");
+MODULE_DESCRIPTION("WM9705 Touch Screen Driver");
+MODULE_LICENSE("GPL");
diff --git a/drivers/input/touchscreen/wm9712.c b/drivers/input/touchscreen/wm9712.c
new file mode 100644
index 000000000000..0b6e4cfa6a21
--- /dev/null
+++ b/drivers/input/touchscreen/wm9712.c
@@ -0,0 +1,462 @@
+/*
+ * wm9712.c -- Codec driver for Wolfson WM9712 AC97 Codecs.
+ *
+ * Copyright 2003, 2004, 2005, 2006, 2007 Wolfson Microelectronics PLC.
+ * Author: Liam Girdwood
+ * liam.girdwood@wolfsonmicro.com or linux@wolfsonmicro.com
+ * Parts Copyright : Ian Molton <spyro@f2s.com>
+ * Andrew Zabolotny <zap@homelink.ru>
+ * Russell King <rmk@arm.linux.org.uk>
+ *
+ * This program is free software; you can redistribute it and/or modify it
+ * under the terms of the GNU General Public License as published by the
+ * Free Software Foundation; either version 2 of the License, or (at your
+ * option) any later version.
+ *
+ */
+
+#include <linux/module.h>
+#include <linux/moduleparam.h>
+#include <linux/version.h>
+#include <linux/kernel.h>
+#include <linux/input.h>
+#include <linux/delay.h>
+#include <linux/bitops.h>
+#include <linux/wm97xx.h>
+
+#define TS_NAME "wm97xx"
+#define WM9712_VERSION "1.00"
+#define DEFAULT_PRESSURE 0xb0c0
+
+/*
+ * Module parameters
+ */
+
+/*
+ * Set internal pull up for pen detect.
+ *
+ * Pull up is in the range 1.02k (least sensitive) to 64k (most sensitive)
+ * i.e. pull up resistance = 64k Ohms / rpu.
+ *
+ * Adjust this value if you are having problems with pen detect not
+ * detecting any down event.
+ */
+static int rpu = 8;
+module_param(rpu, int, 0);
+MODULE_PARM_DESC(rpu, "Set internal pull up resitor for pen detect.");
+
+/*
+ * Set current used for pressure measurement.
+ *
+ * Set pil = 2 to use 400uA
+ * pil = 1 to use 200uA and
+ * pil = 0 to disable pressure measurement.
+ *
+ * This is used to increase the range of values returned by the adc
+ * when measureing touchpanel pressure.
+ */
+static int pil;
+module_param(pil, int, 0);
+MODULE_PARM_DESC(pil, "Set current used for pressure measurement.");
+
+/*
+ * Set threshold for pressure measurement.
+ *
+ * Pen down pressure below threshold is ignored.
+ */
+static int pressure = DEFAULT_PRESSURE & 0xfff;
+module_param(pressure, int, 0);
+MODULE_PARM_DESC(pressure, "Set threshold for pressure measurement.");
+
+/*
+ * Set adc sample delay.
+ *
+ * For accurate touchpanel measurements, some settling time may be
+ * required between the switch matrix applying a voltage across the
+ * touchpanel plate and the ADC sampling the signal.
+ *
+ * This delay can be set by setting delay = n, where n is the array
+ * position of the delay in the array delay_table below.
+ * Long delays > 1ms are supported for completeness, but are not
+ * recommended.
+ */
+static int delay = 3;
+module_param(delay, int, 0);
+MODULE_PARM_DESC(delay, "Set adc sample delay.");
+
+/*
+ * Set five_wire = 1 to use a 5 wire touchscreen.
+ *
+ * NOTE: Five wire mode does not allow for readback of pressure.
+ */
+static int five_wire;
+module_param(five_wire, int, 0);
+MODULE_PARM_DESC(five_wire, "Set to '1' to use 5-wire touchscreen.");
+
+/*
+ * Set adc mask function.
+ *
+ * Sources of glitch noise, such as signals driving an LCD display, may feed
+ * through to the touch screen plates and affect measurement accuracy. In
+ * order to minimise this, a signal may be applied to the MASK pin to delay or
+ * synchronise the sampling.
+ *
+ * 0 = No delay or sync
+ * 1 = High on pin stops conversions
+ * 2 = Edge triggered, edge on pin delays conversion by delay param (above)
+ * 3 = Edge triggered, edge on pin starts conversion after delay param
+ */
+static int mask;
+module_param(mask, int, 0);
+MODULE_PARM_DESC(mask, "Set adc mask function.");
+
+/*
+ * Coordinate Polling Enable.
+ *
+ * Set to 1 to enable coordinate polling. e.g. x,y[,p] is sampled together
+ * for every poll.
+ */
+static int coord;
+module_param(coord, int, 0);
+MODULE_PARM_DESC(coord, "Polling coordinate mode");
+
+/*
+ * ADC sample delay times in uS
+ */
+static const int delay_table[] = {
+ 21, /* 1 AC97 Link frames */
+ 42, /* 2 */
+ 84, /* 4 */
+ 167, /* 8 */
+ 333, /* 16 */
+ 667, /* 32 */
+ 1000, /* 48 */
+ 1333, /* 64 */
+ 2000, /* 96 */
+ 2667, /* 128 */
+ 3333, /* 160 */
+ 4000, /* 192 */
+ 4667, /* 224 */
+ 5333, /* 256 */
+ 6000, /* 288 */
+ 0 /* No delay, switch matrix always on */
+};
+
+/*
+ * Delay after issuing a POLL command.
+ *
+ * The delay is 3 AC97 link frames + the touchpanel settling delay
+ */
+static inline void poll_delay(int d)
+{
+ udelay(3 * AC97_LINK_FRAME + delay_table[d]);
+}
+
+/*
+ * set up the physical settings of the WM9712
+ */
+static void wm9712_phy_init(struct wm97xx *wm)
+{
+ u16 dig1 = 0;
+ u16 dig2 = WM97XX_RPR | WM9712_RPU(1);
+
+ /* WM9712 rpu */
+ if (rpu) {
+ dig2 &= 0xffc0;
+ dig2 |= WM9712_RPU(rpu);
+ dev_dbg(wm->dev, "setting pen detect pull-up to %d Ohms",
+ 64000 / rpu);
+ }
+
+ /* touchpanel pressure current*/
+ if (pil == 2) {
+ dig2 |= WM9712_PIL;
+ dev_dbg(wm->dev,
+ "setting pressure measurement current to 400uA.");
+ } else if (pil)
+ dev_dbg(wm->dev,
+ "setting pressure measurement current to 200uA.");
+ if (!pil)
+ pressure = 0;
+
+ /* WM9712 five wire */
+ if (five_wire) {
+ dig2 |= WM9712_45W;
+ dev_dbg(wm->dev, "setting 5-wire touchscreen mode.");
+ }
+
+ /* polling mode sample settling delay */
+ if (delay < 0 || delay > 15) {
+ dev_dbg(wm->dev, "supplied delay out of range.");
+ delay = 4;
+ }
+ dig1 &= 0xff0f;
+ dig1 |= WM97XX_DELAY(delay);
+ dev_dbg(wm->dev, "setting adc sample delay to %d u Secs.",
+ delay_table[delay]);
+
+ /* mask */
+ dig2 |= ((mask & 0x3) << 6);
+ if (mask) {
+ u16 reg;
+ /* Set GPIO4 as Mask Pin*/
+ reg = wm97xx_reg_read(wm, AC97_MISC_AFE);
+ wm97xx_reg_write(wm, AC97_MISC_AFE, reg | WM97XX_GPIO_4);
+ reg = wm97xx_reg_read(wm, AC97_GPIO_CFG);
+ wm97xx_reg_write(wm, AC97_GPIO_CFG, reg | WM97XX_GPIO_4);
+ }
+
+ /* wait - coord mode */
+ if (coord)
+ dig2 |= WM9712_WAIT;
+
+ wm97xx_reg_write(wm, AC97_WM97XX_DIGITISER1, dig1);
+ wm97xx_reg_write(wm, AC97_WM97XX_DIGITISER2, dig2);
+}
+
+static void wm9712_dig_enable(struct wm97xx *wm, int enable)
+{
+ u16 dig2 = wm->dig[2];
+
+ if (enable) {
+ wm97xx_reg_write(wm, AC97_WM97XX_DIGITISER2,
+ dig2 | WM97XX_PRP_DET_DIG);
+ wm97xx_reg_read(wm, AC97_WM97XX_DIGITISER_RD); /* dummy read */
+ } else
+ wm97xx_reg_write(wm, AC97_WM97XX_DIGITISER2,
+ dig2 & ~WM97XX_PRP_DET_DIG);
+}
+
+static void wm9712_aux_prepare(struct wm97xx *wm)
+{
+ memcpy(wm->dig_save, wm->dig, sizeof(wm->dig));
+ wm97xx_reg_write(wm, AC97_WM97XX_DIGITISER1, 0);
+ wm97xx_reg_write(wm, AC97_WM97XX_DIGITISER2, WM97XX_PRP_DET_DIG);
+}
+
+static void wm9712_dig_restore(struct wm97xx *wm)
+{
+ wm97xx_reg_write(wm, AC97_WM97XX_DIGITISER1, wm->dig_save[1]);
+ wm97xx_reg_write(wm, AC97_WM97XX_DIGITISER2, wm->dig_save[2]);
+}
+
+static inline int is_pden(struct wm97xx *wm)
+{
+ return wm->dig[2] & WM9712_PDEN;
+}
+
+/*
+ * Read a sample from the WM9712 adc in polling mode.
+ */
+static int wm9712_poll_sample(struct wm97xx *wm, int adcsel, int *sample)
+{
+ int timeout = 5 * delay;
+
+ if (!wm->pen_probably_down) {
+ u16 data = wm97xx_reg_read(wm, AC97_WM97XX_DIGITISER_RD);
+ if (!(data & WM97XX_PEN_DOWN))
+ return RC_PENUP;
+ wm->pen_probably_down = 1;
+ }
+
+ /* set up digitiser */
+ if (adcsel & 0x8000)
+ adcsel = ((adcsel & 0x7fff) + 3) << 12;
+
+ if (wm->mach_ops && wm->mach_ops->pre_sample)
+ wm->mach_ops->pre_sample(adcsel);
+ wm97xx_reg_write(wm, AC97_WM97XX_DIGITISER1,
+ adcsel | WM97XX_POLL | WM97XX_DELAY(delay));
+
+ /* wait 3 AC97 time slots + delay for conversion */
+ poll_delay(delay);
+
+ /* wait for POLL to go low */
+ while ((wm97xx_reg_read(wm, AC97_WM97XX_DIGITISER1) & WM97XX_POLL)
+ && timeout) {
+ udelay(AC97_LINK_FRAME);
+ timeout--;
+ }
+
+ if (timeout <= 0) {
+ /* If PDEN is set, we can get a timeout when pen goes up */
+ if (is_pden(wm))
+ wm->pen_probably_down = 0;
+ else
+ dev_dbg(wm->dev, "adc sample timeout");
+ return RC_PENUP;
+ }
+
+ *sample = wm97xx_reg_read(wm, AC97_WM97XX_DIGITISER_RD);
+ if (wm->mach_ops && wm->mach_ops->post_sample)
+ wm->mach_ops->post_sample(adcsel);
+
+ /* check we have correct sample */
+ if ((*sample & WM97XX_ADCSEL_MASK) != adcsel) {
+ dev_dbg(wm->dev, "adc wrong sample, read %x got %x", adcsel,
+ *sample & WM97XX_ADCSEL_MASK);
+ return RC_PENUP;
+ }
+
+ if (!(*sample & WM97XX_PEN_DOWN)) {
+ wm->pen_probably_down = 0;
+ return RC_PENUP;
+ }
+
+ return RC_VALID;
+}
+
+/*
+ * Read a coord from the WM9712 adc in polling mode.
+ */
+static int wm9712_poll_coord(struct wm97xx *wm, struct wm97xx_data *data)
+{
+ int timeout = 5 * delay;
+
+ if (!wm->pen_probably_down) {
+ u16 data_rd = wm97xx_reg_read(wm, AC97_WM97XX_DIGITISER_RD);
+ if (!(data_rd & WM97XX_PEN_DOWN))
+ return RC_PENUP;
+ wm->pen_probably_down = 1;
+ }
+
+ /* set up digitiser */
+ if (wm->mach_ops && wm->mach_ops->pre_sample)
+ wm->mach_ops->pre_sample(WM97XX_ADCSEL_X | WM97XX_ADCSEL_Y);
+
+ wm97xx_reg_write(wm, AC97_WM97XX_DIGITISER1,
+ WM97XX_COO | WM97XX_POLL | WM97XX_DELAY(delay));
+
+ /* wait 3 AC97 time slots + delay for conversion and read x */
+ poll_delay(delay);
+ data->x = wm97xx_reg_read(wm, AC97_WM97XX_DIGITISER_RD);
+ /* wait for POLL to go low */
+ while ((wm97xx_reg_read(wm, AC97_WM97XX_DIGITISER1) & WM97XX_POLL)
+ && timeout) {
+ udelay(AC97_LINK_FRAME);
+ timeout--;
+ }
+
+ if (timeout <= 0) {
+ /* If PDEN is set, we can get a timeout when pen goes up */
+ if (is_pden(wm))
+ wm->pen_probably_down = 0;
+ else
+ dev_dbg(wm->dev, "adc sample timeout");
+ return RC_PENUP;
+ }
+
+ /* read back y data */
+ data->y = wm97xx_reg_read(wm, AC97_WM97XX_DIGITISER_RD);
+ if (pil)
+ data->p = wm97xx_reg_read(wm, AC97_WM97XX_DIGITISER_RD);
+ else
+ data->p = DEFAULT_PRESSURE;
+
+ if (wm->mach_ops && wm->mach_ops->post_sample)
+ wm->mach_ops->post_sample(WM97XX_ADCSEL_X | WM97XX_ADCSEL_Y);
+
+ /* check we have correct sample */
+ if (!(data->x & WM97XX_ADCSEL_X) || !(data->y & WM97XX_ADCSEL_Y))
+ goto err;
+ if (pil && !(data->p & WM97XX_ADCSEL_PRES))
+ goto err;
+
+ if (!(data->x & WM97XX_PEN_DOWN) || !(data->y & WM97XX_PEN_DOWN)) {
+ wm->pen_probably_down = 0;
+ return RC_PENUP;
+ }
+ return RC_VALID;
+err:
+ return 0;
+}
+
+/*
+ * Sample the WM9712 touchscreen in polling mode
+ */
+static int wm9712_poll_touch(struct wm97xx *wm, struct wm97xx_data *data)
+{
+ int rc;
+
+ if (coord) {
+ rc = wm9712_poll_coord(wm, data);
+ if (rc != RC_VALID)
+ return rc;
+ } else {
+ rc = wm9712_poll_sample(wm, WM97XX_ADCSEL_X, &data->x);
+ if (rc != RC_VALID)
+ return rc;
+
+ rc = wm9712_poll_sample(wm, WM97XX_ADCSEL_Y, &data->y);
+ if (rc != RC_VALID)
+ return rc;
+
+ if (pil && !five_wire) {
+ rc = wm9712_poll_sample(wm, WM97XX_ADCSEL_PRES,
+ &data->p);
+ if (rc != RC_VALID)
+ return rc;
+ } else
+ data->p = DEFAULT_PRESSURE;
+ }
+ return RC_VALID;
+}
+
+/*
+ * Enable WM9712 continuous mode, i.e. touch data is streamed across
+ * an AC97 slot
+ */
+static int wm9712_acc_enable(struct wm97xx *wm, int enable)
+{
+ u16 dig1, dig2;
+ int ret = 0;
+
+ dig1 = wm->dig[1];
+ dig2 = wm->dig[2];
+
+ if (enable) {
+ /* continous mode */
+ if (wm->mach_ops->acc_startup) {
+ ret = wm->mach_ops->acc_startup(wm);
+ if (ret < 0)
+ return ret;
+ }
+ dig1 &= ~(WM97XX_CM_RATE_MASK | WM97XX_ADCSEL_MASK |
+ WM97XX_DELAY_MASK | WM97XX_SLT_MASK);
+ dig1 |= WM97XX_CTC | WM97XX_COO | WM97XX_SLEN |
+ WM97XX_DELAY(delay) |
+ WM97XX_SLT(wm->acc_slot) |
+ WM97XX_RATE(wm->acc_rate);
+ if (pil)
+ dig1 |= WM97XX_ADCSEL_PRES;
+ dig2 |= WM9712_PDEN;
+ } else {
+ dig1 &= ~(WM97XX_CTC | WM97XX_COO | WM97XX_SLEN);
+ dig2 &= ~WM9712_PDEN;
+ if (wm->mach_ops->acc_shutdown)
+ wm->mach_ops->acc_shutdown(wm);
+ }
+
+ wm97xx_reg_write(wm, AC97_WM97XX_DIGITISER1, dig1);
+ wm97xx_reg_write(wm, AC97_WM97XX_DIGITISER2, dig2);
+
+ return 0;
+}
+
+struct wm97xx_codec_drv wm9712_codec = {
+ .id = WM9712_ID2,
+ .name = "wm9712",
+ .poll_sample = wm9712_poll_sample,
+ .poll_touch = wm9712_poll_touch,
+ .acc_enable = wm9712_acc_enable,
+ .phy_init = wm9712_phy_init,
+ .dig_enable = wm9712_dig_enable,
+ .dig_restore = wm9712_dig_restore,
+ .aux_prepare = wm9712_aux_prepare,
+};
+EXPORT_SYMBOL_GPL(wm9712_codec);
+
+/* Module information */
+MODULE_AUTHOR("Liam Girdwood <liam.girdwood@wolfsonmicro.com>");
+MODULE_DESCRIPTION("WM9712 Touch Screen Driver");
+MODULE_LICENSE("GPL");
diff --git a/drivers/input/touchscreen/wm9713.c b/drivers/input/touchscreen/wm9713.c
new file mode 100644
index 000000000000..01278bd7e65c
--- /dev/null
+++ b/drivers/input/touchscreen/wm9713.c
@@ -0,0 +1,460 @@
+/*
+ * wm9713.c -- Codec touch driver for Wolfson WM9713 AC97 Codec.
+ *
+ * Copyright 2003, 2004, 2005, 2006, 2007, 2008 Wolfson Microelectronics PLC.
+ * Author: Liam Girdwood
+ * liam.girdwood@wolfsonmicro.com or linux@wolfsonmicro.com
+ * Parts Copyright : Ian Molton <spyro@f2s.com>
+ * Andrew Zabolotny <zap@homelink.ru>
+ * Russell King <rmk@arm.linux.org.uk>
+ *
+ * This program is free software; you can redistribute it and/or modify it
+ * under the terms of the GNU General Public License as published by the
+ * Free Software Foundation; either version 2 of the License, or (at your
+ * option) any later version.
+ *
+ */
+
+#include <linux/module.h>
+#include <linux/moduleparam.h>
+#include <linux/version.h>
+#include <linux/kernel.h>
+#include <linux/input.h>
+#include <linux/delay.h>
+#include <linux/bitops.h>
+#include <linux/wm97xx.h>
+
+#define TS_NAME "wm97xx"
+#define WM9713_VERSION "1.00"
+#define DEFAULT_PRESSURE 0xb0c0
+
+/*
+ * Module parameters
+ */
+
+/*
+ * Set internal pull up for pen detect.
+ *
+ * Pull up is in the range 1.02k (least sensitive) to 64k (most sensitive)
+ * i.e. pull up resistance = 64k Ohms / rpu.
+ *
+ * Adjust this value if you are having problems with pen detect not
+ * detecting any down event.
+ */
+static int rpu = 8;
+module_param(rpu, int, 0);
+MODULE_PARM_DESC(rpu, "Set internal pull up resitor for pen detect.");
+
+/*
+ * Set current used for pressure measurement.
+ *
+ * Set pil = 2 to use 400uA
+ * pil = 1 to use 200uA and
+ * pil = 0 to disable pressure measurement.
+ *
+ * This is used to increase the range of values returned by the adc
+ * when measureing touchpanel pressure.
+ */
+static int pil;
+module_param(pil, int, 0);
+MODULE_PARM_DESC(pil, "Set current used for pressure measurement.");
+
+/*
+ * Set threshold for pressure measurement.
+ *
+ * Pen down pressure below threshold is ignored.
+ */
+static int pressure = DEFAULT_PRESSURE & 0xfff;
+module_param(pressure, int, 0);
+MODULE_PARM_DESC(pressure, "Set threshold for pressure measurement.");
+
+/*
+ * Set adc sample delay.
+ *
+ * For accurate touchpanel measurements, some settling time may be
+ * required between the switch matrix applying a voltage across the
+ * touchpanel plate and the ADC sampling the signal.
+ *
+ * This delay can be set by setting delay = n, where n is the array
+ * position of the delay in the array delay_table below.
+ * Long delays > 1ms are supported for completeness, but are not
+ * recommended.
+ */
+static int delay = 4;
+module_param(delay, int, 0);
+MODULE_PARM_DESC(delay, "Set adc sample delay.");
+
+/*
+ * Set adc mask function.
+ *
+ * Sources of glitch noise, such as signals driving an LCD display, may feed
+ * through to the touch screen plates and affect measurement accuracy. In
+ * order to minimise this, a signal may be applied to the MASK pin to delay or
+ * synchronise the sampling.
+ *
+ * 0 = No delay or sync
+ * 1 = High on pin stops conversions
+ * 2 = Edge triggered, edge on pin delays conversion by delay param (above)
+ * 3 = Edge triggered, edge on pin starts conversion after delay param
+ */
+static int mask;
+module_param(mask, int, 0);
+MODULE_PARM_DESC(mask, "Set adc mask function.");
+
+/*
+ * Coordinate Polling Enable.
+ *
+ * Set to 1 to enable coordinate polling. e.g. x,y[,p] is sampled together
+ * for every poll.
+ */
+static int coord;
+module_param(coord, int, 0);
+MODULE_PARM_DESC(coord, "Polling coordinate mode");
+
+/*
+ * ADC sample delay times in uS
+ */
+static const int delay_table[] = {
+ 21, /* 1 AC97 Link frames */
+ 42, /* 2 */
+ 84, /* 4 */
+ 167, /* 8 */
+ 333, /* 16 */
+ 667, /* 32 */
+ 1000, /* 48 */
+ 1333, /* 64 */
+ 2000, /* 96 */
+ 2667, /* 128 */
+ 3333, /* 160 */
+ 4000, /* 192 */
+ 4667, /* 224 */
+ 5333, /* 256 */
+ 6000, /* 288 */
+ 0 /* No delay, switch matrix always on */
+};
+
+/*
+ * Delay after issuing a POLL command.
+ *
+ * The delay is 3 AC97 link frames + the touchpanel settling delay
+ */
+static inline void poll_delay(int d)
+{
+ udelay(3 * AC97_LINK_FRAME + delay_table[d]);
+}
+
+/*
+ * set up the physical settings of the WM9713
+ */
+static void wm9713_phy_init(struct wm97xx *wm)
+{
+ u16 dig1 = 0, dig2, dig3;
+
+ /* default values */
+ dig2 = WM97XX_DELAY(4) | WM97XX_SLT(5);
+ dig3 = WM9712_RPU(1);
+
+ /* rpu */
+ if (rpu) {
+ dig3 &= 0xffc0;
+ dig3 |= WM9712_RPU(rpu);
+ dev_info(wm->dev, "setting pen detect pull-up to %d Ohms\n",
+ 64000 / rpu);
+ }
+
+ /* touchpanel pressure */
+ if (pil == 2) {
+ dig3 |= WM9712_PIL;
+ dev_info(wm->dev,
+ "setting pressure measurement current to 400uA.");
+ } else if (pil)
+ dev_info(wm->dev,
+ "setting pressure measurement current to 200uA.");
+ if (!pil)
+ pressure = 0;
+
+ /* sample settling delay */
+ if (delay < 0 || delay > 15) {
+ dev_info(wm->dev, "supplied delay out of range.");
+ delay = 4;
+ dev_info(wm->dev, "setting adc sample delay to %d u Secs.",
+ delay_table[delay]);
+ }
+ dig2 &= 0xff0f;
+ dig2 |= WM97XX_DELAY(delay);
+
+ /* mask */
+ dig3 |= ((mask & 0x3) << 4);
+ if (coord)
+ dig3 |= WM9713_WAIT;
+
+ wm->misc = wm97xx_reg_read(wm, 0x5a);
+
+ wm97xx_reg_write(wm, AC97_WM9713_DIG1, dig1);
+ wm97xx_reg_write(wm, AC97_WM9713_DIG2, dig2);
+ wm97xx_reg_write(wm, AC97_WM9713_DIG3, dig3);
+ wm97xx_reg_write(wm, AC97_GPIO_STICKY, 0x0);
+}
+
+static void wm9713_dig_enable(struct wm97xx *wm, int enable)
+{
+ u16 val;
+
+ if (enable) {
+ val = wm97xx_reg_read(wm, AC97_EXTENDED_MID);
+ wm97xx_reg_write(wm, AC97_EXTENDED_MID, val & 0x7fff);
+ wm97xx_reg_write(wm, AC97_WM9713_DIG3, wm->dig[2] |
+ WM97XX_PRP_DET_DIG);
+ wm97xx_reg_read(wm, AC97_WM97XX_DIGITISER_RD); /* dummy read */
+ } else {
+ wm97xx_reg_write(wm, AC97_WM9713_DIG3, wm->dig[2] &
+ ~WM97XX_PRP_DET_DIG);
+ val = wm97xx_reg_read(wm, AC97_EXTENDED_MID);
+ wm97xx_reg_write(wm, AC97_EXTENDED_MID, val | 0x8000);
+ }
+}
+
+static void wm9713_dig_restore(struct wm97xx *wm)
+{
+ wm97xx_reg_write(wm, AC97_WM9713_DIG1, wm->dig_save[0]);
+ wm97xx_reg_write(wm, AC97_WM9713_DIG2, wm->dig_save[1]);
+ wm97xx_reg_write(wm, AC97_WM9713_DIG3, wm->dig_save[2]);
+}
+
+static void wm9713_aux_prepare(struct wm97xx *wm)
+{
+ memcpy(wm->dig_save, wm->dig, sizeof(wm->dig));
+ wm97xx_reg_write(wm, AC97_WM9713_DIG1, 0);
+ wm97xx_reg_write(wm, AC97_WM9713_DIG2, 0);
+ wm97xx_reg_write(wm, AC97_WM9713_DIG3, WM97XX_PRP_DET_DIG);
+}
+
+static inline int is_pden(struct wm97xx *wm)
+{
+ return wm->dig[2] & WM9713_PDEN;
+}
+
+/*
+ * Read a sample from the WM9713 adc in polling mode.
+ */
+static int wm9713_poll_sample(struct wm97xx *wm, int adcsel, int *sample)
+{
+ u16 dig1;
+ int timeout = 5 * delay;
+
+ if (!wm->pen_probably_down) {
+ u16 data = wm97xx_reg_read(wm, AC97_WM97XX_DIGITISER_RD);
+ if (!(data & WM97XX_PEN_DOWN))
+ return RC_PENUP;
+ wm->pen_probably_down = 1;
+ }
+
+ /* set up digitiser */
+ if (adcsel & 0x8000)
+ adcsel = 1 << ((adcsel & 0x7fff) + 3);
+
+ dig1 = wm97xx_reg_read(wm, AC97_WM9713_DIG1);
+ dig1 &= ~WM9713_ADCSEL_MASK;
+
+ if (wm->mach_ops && wm->mach_ops->pre_sample)
+ wm->mach_ops->pre_sample(adcsel);
+ wm97xx_reg_write(wm, AC97_WM9713_DIG1, dig1 | adcsel | WM9713_POLL);
+
+ /* wait 3 AC97 time slots + delay for conversion */
+ poll_delay(delay);
+
+ /* wait for POLL to go low */
+ while ((wm97xx_reg_read(wm, AC97_WM9713_DIG1) & WM9713_POLL) &&
+ timeout) {
+ udelay(AC97_LINK_FRAME);
+ timeout--;
+ }
+
+ if (timeout <= 0) {
+ /* If PDEN is set, we can get a timeout when pen goes up */
+ if (is_pden(wm))
+ wm->pen_probably_down = 0;
+ else
+ dev_dbg(wm->dev, "adc sample timeout");
+ return RC_PENUP;
+ }
+
+ *sample = wm97xx_reg_read(wm, AC97_WM97XX_DIGITISER_RD);
+ if (wm->mach_ops && wm->mach_ops->post_sample)
+ wm->mach_ops->post_sample(adcsel);
+
+ /* check we have correct sample */
+ if ((*sample & WM97XX_ADCSRC_MASK) != ffs(adcsel >> 1) << 12) {
+ dev_dbg(wm->dev, "adc wrong sample, read %x got %x", adcsel,
+ *sample & WM97XX_ADCSRC_MASK);
+ return RC_PENUP;
+ }
+
+ if (!(*sample & WM97XX_PEN_DOWN)) {
+ wm->pen_probably_down = 0;
+ return RC_PENUP;
+ }
+
+ return RC_VALID;
+}
+
+/*
+ * Read a coordinate from the WM9713 adc in polling mode.
+ */
+static int wm9713_poll_coord(struct wm97xx *wm, struct wm97xx_data *data)
+{
+ u16 dig1;
+ int timeout = 5 * delay;
+
+ if (!wm->pen_probably_down) {
+ u16 val = wm97xx_reg_read(wm, AC97_WM97XX_DIGITISER_RD);
+ if (!(val & WM97XX_PEN_DOWN))
+ return RC_PENUP;
+ wm->pen_probably_down = 1;
+ }
+
+ /* set up digitiser */
+ dig1 = wm97xx_reg_read(wm, AC97_WM9713_DIG1);
+ dig1 &= ~WM9713_ADCSEL_MASK;
+ if (pil)
+ dig1 |= WM9713_ADCSEL_PRES;
+
+ if (wm->mach_ops && wm->mach_ops->pre_sample)
+ wm->mach_ops->pre_sample(WM97XX_ADCSEL_X | WM97XX_ADCSEL_Y);
+ wm97xx_reg_write(wm, AC97_WM9713_DIG1,
+ dig1 | WM9713_POLL | WM9713_COO);
+
+ /* wait 3 AC97 time slots + delay for conversion */
+ poll_delay(delay);
+ data->x = wm97xx_reg_read(wm, AC97_WM97XX_DIGITISER_RD);
+ /* wait for POLL to go low */
+ while ((wm97xx_reg_read(wm, AC97_WM9713_DIG1) & WM9713_POLL)
+ && timeout) {
+ udelay(AC97_LINK_FRAME);
+ timeout--;
+ }
+
+ if (timeout <= 0) {
+ /* If PDEN is set, we can get a timeout when pen goes up */
+ if (is_pden(wm))
+ wm->pen_probably_down = 0;
+ else
+ dev_dbg(wm->dev, "adc sample timeout");
+ return RC_PENUP;
+ }
+
+ /* read back data */
+ data->y = wm97xx_reg_read(wm, AC97_WM97XX_DIGITISER_RD);
+ if (pil)
+ data->p = wm97xx_reg_read(wm, AC97_WM97XX_DIGITISER_RD);
+ else
+ data->p = DEFAULT_PRESSURE;
+
+ if (wm->mach_ops && wm->mach_ops->post_sample)
+ wm->mach_ops->post_sample(WM97XX_ADCSEL_X | WM97XX_ADCSEL_Y);
+
+ /* check we have correct sample */
+ if (!(data->x & WM97XX_ADCSEL_X) || !(data->y & WM97XX_ADCSEL_Y))
+ goto err;
+ if (pil && !(data->p & WM97XX_ADCSEL_PRES))
+ goto err;
+
+ if (!(data->x & WM97XX_PEN_DOWN) || !(data->y & WM97XX_PEN_DOWN)) {
+ wm->pen_probably_down = 0;
+ return RC_PENUP;
+ }
+ return RC_VALID;
+err:
+ return 0;
+}
+
+/*
+ * Sample the WM9713 touchscreen in polling mode
+ */
+static int wm9713_poll_touch(struct wm97xx *wm, struct wm97xx_data *data)
+{
+ int rc;
+
+ if (coord) {
+ rc = wm9713_poll_coord(wm, data);
+ if (rc != RC_VALID)
+ return rc;
+ } else {
+ rc = wm9713_poll_sample(wm, WM9713_ADCSEL_X, &data->x);
+ if (rc != RC_VALID)
+ return rc;
+ rc = wm9713_poll_sample(wm, WM9713_ADCSEL_Y, &data->y);
+ if (rc != RC_VALID)
+ return rc;
+ if (pil) {
+ rc = wm9713_poll_sample(wm, WM9713_ADCSEL_PRES,
+ &data->p);
+ if (rc != RC_VALID)
+ return rc;
+ } else
+ data->p = DEFAULT_PRESSURE;
+ }
+ return RC_VALID;
+}
+
+/*
+ * Enable WM9713 continuous mode, i.e. touch data is streamed across
+ * an AC97 slot
+ */
+static int wm9713_acc_enable(struct wm97xx *wm, int enable)
+{
+ u16 dig1, dig2, dig3;
+ int ret = 0;
+
+ dig1 = wm->dig[0];
+ dig2 = wm->dig[1];
+ dig3 = wm->dig[2];
+
+ if (enable) {
+ /* continous mode */
+ if (wm->mach_ops->acc_startup &&
+ (ret = wm->mach_ops->acc_startup(wm)) < 0)
+ return ret;
+
+ dig1 &= ~WM9713_ADCSEL_MASK;
+ dig1 |= WM9713_CTC | WM9713_COO | WM9713_ADCSEL_X |
+ WM9713_ADCSEL_Y;
+ if (pil)
+ dig1 |= WM9713_ADCSEL_PRES;
+ dig2 &= ~(WM97XX_DELAY_MASK | WM97XX_SLT_MASK |
+ WM97XX_CM_RATE_MASK);
+ dig2 |= WM97XX_SLEN | WM97XX_DELAY(delay) |
+ WM97XX_SLT(wm->acc_slot) | WM97XX_RATE(wm->acc_rate);
+ dig3 |= WM9713_PDEN;
+ } else {
+ dig1 &= ~(WM9713_CTC | WM9713_COO);
+ dig2 &= ~WM97XX_SLEN;
+ dig3 &= ~WM9713_PDEN;
+ if (wm->mach_ops->acc_shutdown)
+ wm->mach_ops->acc_shutdown(wm);
+ }
+
+ wm97xx_reg_write(wm, AC97_WM9713_DIG1, dig1);
+ wm97xx_reg_write(wm, AC97_WM9713_DIG2, dig2);
+ wm97xx_reg_write(wm, AC97_WM9713_DIG3, dig3);
+
+ return ret;
+}
+
+struct wm97xx_codec_drv wm9713_codec = {
+ .id = WM9713_ID2,
+ .name = "wm9713",
+ .poll_sample = wm9713_poll_sample,
+ .poll_touch = wm9713_poll_touch,
+ .acc_enable = wm9713_acc_enable,
+ .phy_init = wm9713_phy_init,
+ .dig_enable = wm9713_dig_enable,
+ .dig_restore = wm9713_dig_restore,
+ .aux_prepare = wm9713_aux_prepare,
+};
+EXPORT_SYMBOL_GPL(wm9713_codec);
+
+/* Module information */
+MODULE_AUTHOR("Liam Girdwood <liam.girdwood@wolfsonmicro.com>");
+MODULE_DESCRIPTION("WM9713 Touch Screen Driver");
+MODULE_LICENSE("GPL");
diff --git a/drivers/input/touchscreen/wm97xx-core.c b/drivers/input/touchscreen/wm97xx-core.c
new file mode 100644
index 000000000000..e9c7ea46b6e3
--- /dev/null
+++ b/drivers/input/touchscreen/wm97xx-core.c
@@ -0,0 +1,829 @@
+/*
+ * wm97xx-core.c -- Touch screen driver core for Wolfson WM9705, WM9712
+ * and WM9713 AC97 Codecs.
+ *
+ * Copyright 2003, 2004, 2005, 2006, 2007, 2008 Wolfson Microelectronics PLC.
+ * Author: Liam Girdwood
+ * liam.girdwood@wolfsonmicro.com or linux@wolfsonmicro.com
+ * Parts Copyright : Ian Molton <spyro@f2s.com>
+ * Andrew Zabolotny <zap@homelink.ru>
+ * Russell King <rmk@arm.linux.org.uk>
+ *
+ * This program is free software; you can redistribute it and/or modify it
+ * under the terms of the GNU General Public License as published by the
+ * Free Software Foundation; either version 2 of the License, or (at your
+ * option) any later version.
+ *
+ * Notes:
+ *
+ * Features:
+ * - supports WM9705, WM9712, WM9713
+ * - polling mode
+ * - continuous mode (arch-dependent)
+ * - adjustable rpu/dpp settings
+ * - adjustable pressure current
+ * - adjustable sample settle delay
+ * - 4 and 5 wire touchscreens (5 wire is WM9712 only)
+ * - pen down detection
+ * - battery monitor
+ * - sample AUX adcs
+ * - power management
+ * - codec GPIO
+ * - codec event notification
+ * Todo
+ * - Support for async sampling control for noisy LCDs.
+ *
+ */
+
+#include <linux/module.h>
+#include <linux/moduleparam.h>
+#include <linux/version.h>
+#include <linux/kernel.h>
+#include <linux/init.h>
+#include <linux/delay.h>
+#include <linux/string.h>
+#include <linux/proc_fs.h>
+#include <linux/pm.h>
+#include <linux/interrupt.h>
+#include <linux/bitops.h>
+#include <linux/workqueue.h>
+#include <linux/wm97xx.h>
+#include <linux/uaccess.h>
+#include <linux/io.h>
+
+#define TS_NAME "wm97xx"
+#define WM_CORE_VERSION "1.00"
+#define DEFAULT_PRESSURE 0xb0c0
+
+
+/*
+ * Touchscreen absolute values
+ *
+ * These parameters are used to help the input layer discard out of
+ * range readings and reduce jitter etc.
+ *
+ * o min, max:- indicate the min and max values your touch screen returns
+ * o fuzz:- use a higher number to reduce jitter
+ *
+ * The default values correspond to Mainstone II in QVGA mode
+ *
+ * Please read
+ * Documentation/input/input-programming.txt for more details.
+ */
+
+static int abs_x[3] = {350, 3900, 5};
+module_param_array(abs_x, int, NULL, 0);
+MODULE_PARM_DESC(abs_x, "Touchscreen absolute X min, max, fuzz");
+
+static int abs_y[3] = {320, 3750, 40};
+module_param_array(abs_y, int, NULL, 0);
+MODULE_PARM_DESC(abs_y, "Touchscreen absolute Y min, max, fuzz");
+
+static int abs_p[3] = {0, 150, 4};
+module_param_array(abs_p, int, NULL, 0);
+MODULE_PARM_DESC(abs_p, "Touchscreen absolute Pressure min, max, fuzz");
+
+/*
+ * wm97xx IO access, all IO locking done by AC97 layer
+ */
+int wm97xx_reg_read(struct wm97xx *wm, u16 reg)
+{
+ if (wm->ac97)
+ return wm->ac97->bus->ops->read(wm->ac97, reg);
+ else
+ return -1;
+}
+EXPORT_SYMBOL_GPL(wm97xx_reg_read);
+
+void wm97xx_reg_write(struct wm97xx *wm, u16 reg, u16 val)
+{
+ /* cache digitiser registers */
+ if (reg >= AC97_WM9713_DIG1 && reg <= AC97_WM9713_DIG3)
+ wm->dig[(reg - AC97_WM9713_DIG1) >> 1] = val;
+
+ /* cache gpio regs */
+ if (reg >= AC97_GPIO_CFG && reg <= AC97_MISC_AFE)
+ wm->gpio[(reg - AC97_GPIO_CFG) >> 1] = val;
+
+ /* wm9713 irq reg */
+ if (reg == 0x5a)
+ wm->misc = val;
+
+ if (wm->ac97)
+ wm->ac97->bus->ops->write(wm->ac97, reg, val);
+}
+EXPORT_SYMBOL_GPL(wm97xx_reg_write);
+
+/**
+ * wm97xx_read_aux_adc - Read the aux adc.
+ * @wm: wm97xx device.
+ * @adcsel: codec ADC to be read
+ *
+ * Reads the selected AUX ADC.
+ */
+
+int wm97xx_read_aux_adc(struct wm97xx *wm, u16 adcsel)
+{
+ int power_adc = 0, auxval;
+ u16 power = 0;
+
+ /* get codec */
+ mutex_lock(&wm->codec_mutex);
+
+ /* When the touchscreen is not in use, we may have to power up
+ * the AUX ADC before we can use sample the AUX inputs->
+ */
+ if (wm->id == WM9713_ID2 &&
+ (power = wm97xx_reg_read(wm, AC97_EXTENDED_MID)) & 0x8000) {
+ power_adc = 1;
+ wm97xx_reg_write(wm, AC97_EXTENDED_MID, power & 0x7fff);
+ }
+
+ /* Prepare the codec for AUX reading */
+ wm->codec->aux_prepare(wm);
+
+ /* Turn polling mode on to read AUX ADC */
+ wm->pen_probably_down = 1;
+ wm->codec->poll_sample(wm, adcsel, &auxval);
+
+ if (power_adc)
+ wm97xx_reg_write(wm, AC97_EXTENDED_MID, power | 0x8000);
+
+ wm->codec->dig_restore(wm);
+
+ wm->pen_probably_down = 0;
+
+ mutex_unlock(&wm->codec_mutex);
+ return auxval & 0xfff;
+}
+EXPORT_SYMBOL_GPL(wm97xx_read_aux_adc);
+
+/**
+ * wm97xx_get_gpio - Get the status of a codec GPIO.
+ * @wm: wm97xx device.
+ * @gpio: gpio
+ *
+ * Get the status of a codec GPIO pin
+ */
+
+enum wm97xx_gpio_status wm97xx_get_gpio(struct wm97xx *wm, u32 gpio)
+{
+ u16 status;
+ enum wm97xx_gpio_status ret;
+
+ mutex_lock(&wm->codec_mutex);
+ status = wm97xx_reg_read(wm, AC97_GPIO_STATUS);
+
+ if (status & gpio)
+ ret = WM97XX_GPIO_HIGH;
+ else
+ ret = WM97XX_GPIO_LOW;
+
+ mutex_unlock(&wm->codec_mutex);
+ return ret;
+}
+EXPORT_SYMBOL_GPL(wm97xx_get_gpio);
+
+/**
+ * wm97xx_set_gpio - Set the status of a codec GPIO.
+ * @wm: wm97xx device.
+ * @gpio: gpio
+ *
+ *
+ * Set the status of a codec GPIO pin
+ */
+
+void wm97xx_set_gpio(struct wm97xx *wm, u32 gpio,
+ enum wm97xx_gpio_status status)
+{
+ u16 reg;
+
+ mutex_lock(&wm->codec_mutex);
+ reg = wm97xx_reg_read(wm, AC97_GPIO_STATUS);
+
+ if (status & WM97XX_GPIO_HIGH)
+ reg |= gpio;
+ else
+ reg &= ~gpio;
+
+ if (wm->id == WM9712_ID2)
+ wm97xx_reg_write(wm, AC97_GPIO_STATUS, reg << 1);
+ else
+ wm97xx_reg_write(wm, AC97_GPIO_STATUS, reg);
+ mutex_unlock(&wm->codec_mutex);
+}
+EXPORT_SYMBOL_GPL(wm97xx_set_gpio);
+
+/*
+ * Codec GPIO pin configuration, this sets pin direction, polarity,
+ * stickyness and wake up.
+ */
+void wm97xx_config_gpio(struct wm97xx *wm, u32 gpio, enum wm97xx_gpio_dir dir,
+ enum wm97xx_gpio_pol pol, enum wm97xx_gpio_sticky sticky,
+ enum wm97xx_gpio_wake wake)
+{
+ u16 reg;
+
+ mutex_lock(&wm->codec_mutex);
+ reg = wm97xx_reg_read(wm, AC97_GPIO_POLARITY);
+
+ if (pol == WM97XX_GPIO_POL_HIGH)
+ reg |= gpio;
+ else
+ reg &= ~gpio;
+
+ wm97xx_reg_write(wm, AC97_GPIO_POLARITY, reg);
+ reg = wm97xx_reg_read(wm, AC97_GPIO_STICKY);
+
+ if (sticky == WM97XX_GPIO_STICKY)
+ reg |= gpio;
+ else
+ reg &= ~gpio;
+
+ wm97xx_reg_write(wm, AC97_GPIO_STICKY, reg);
+ reg = wm97xx_reg_read(wm, AC97_GPIO_WAKEUP);
+
+ if (wake == WM97XX_GPIO_WAKE)
+ reg |= gpio;
+ else
+ reg &= ~gpio;
+
+ wm97xx_reg_write(wm, AC97_GPIO_WAKEUP, reg);
+ reg = wm97xx_reg_read(wm, AC97_GPIO_CFG);
+
+ if (dir == WM97XX_GPIO_IN)
+ reg |= gpio;
+ else
+ reg &= ~gpio;
+
+ wm97xx_reg_write(wm, AC97_GPIO_CFG, reg);
+ mutex_unlock(&wm->codec_mutex);
+}
+EXPORT_SYMBOL_GPL(wm97xx_config_gpio);
+
+/*
+ * Configure the WM97XX_PRP value to use while system is suspended.
+ * If a value other than 0 is set then WM97xx pen detection will be
+ * left enabled in the configured mode while the system is in suspend,
+ * the device has users and suspend has not been disabled via the
+ * wakeup sysfs entries.
+ *
+ * @wm: WM97xx device to configure
+ * @mode: WM97XX_PRP value to configure while suspended
+ */
+void wm97xx_set_suspend_mode(struct wm97xx *wm, u16 mode)
+{
+ wm->suspend_mode = mode;
+ device_init_wakeup(&wm->input_dev->dev, mode != 0);
+}
+EXPORT_SYMBOL_GPL(wm97xx_set_suspend_mode);
+
+/*
+ * Handle a pen down interrupt.
+ */
+static void wm97xx_pen_irq_worker(struct work_struct *work)
+{
+ struct wm97xx *wm = container_of(work, struct wm97xx, pen_event_work);
+ int pen_was_down = wm->pen_is_down;
+
+ /* do we need to enable the touch panel reader */
+ if (wm->id == WM9705_ID2) {
+ if (wm97xx_reg_read(wm, AC97_WM97XX_DIGITISER_RD) &
+ WM97XX_PEN_DOWN)
+ wm->pen_is_down = 1;
+ else
+ wm->pen_is_down = 0;
+ } else {
+ u16 status, pol;
+ mutex_lock(&wm->codec_mutex);
+ status = wm97xx_reg_read(wm, AC97_GPIO_STATUS);
+ pol = wm97xx_reg_read(wm, AC97_GPIO_POLARITY);
+
+ if (WM97XX_GPIO_13 & pol & status) {
+ wm->pen_is_down = 1;
+ wm97xx_reg_write(wm, AC97_GPIO_POLARITY, pol &
+ ~WM97XX_GPIO_13);
+ } else {
+ wm->pen_is_down = 0;
+ wm97xx_reg_write(wm, AC97_GPIO_POLARITY, pol |
+ WM97XX_GPIO_13);
+ }
+
+ if (wm->id == WM9712_ID2)
+ wm97xx_reg_write(wm, AC97_GPIO_STATUS, (status &
+ ~WM97XX_GPIO_13) << 1);
+ else
+ wm97xx_reg_write(wm, AC97_GPIO_STATUS, status &
+ ~WM97XX_GPIO_13);
+ mutex_unlock(&wm->codec_mutex);
+ }
+
+ /* If the system is not using continuous mode or it provides a
+ * pen down operation then we need to schedule polls while the
+ * pen is down. Otherwise the machine driver is responsible
+ * for scheduling reads.
+ */
+ if (!wm->mach_ops->acc_enabled || wm->mach_ops->acc_pen_down) {
+ if (wm->pen_is_down && !pen_was_down) {
+ /* Data is not availiable immediately on pen down */
+ queue_delayed_work(wm->ts_workq, &wm->ts_reader, 1);
+ }
+
+ /* Let ts_reader report the pen up for debounce. */
+ if (!wm->pen_is_down && pen_was_down)
+ wm->pen_is_down = 1;
+ }
+
+ if (!wm->pen_is_down && wm->mach_ops->acc_enabled)
+ wm->mach_ops->acc_pen_up(wm);
+
+ wm->mach_ops->irq_enable(wm, 1);
+}
+
+/*
+ * Codec PENDOWN irq handler
+ *
+ * We have to disable the codec interrupt in the handler because it
+ * can take upto 1ms to clear the interrupt source. We schedule a task
+ * in a work queue to do the actual interaction with the chip. The
+ * interrupt is then enabled again in the slow handler when the source
+ * has been cleared.
+ */
+static irqreturn_t wm97xx_pen_interrupt(int irq, void *dev_id)
+{
+ struct wm97xx *wm = dev_id;
+
+ if (!work_pending(&wm->pen_event_work)) {
+ wm->mach_ops->irq_enable(wm, 0);
+ queue_work(wm->ts_workq, &wm->pen_event_work);
+ }
+
+ return IRQ_HANDLED;
+}
+
+/*
+ * initialise pen IRQ handler and workqueue
+ */
+static int wm97xx_init_pen_irq(struct wm97xx *wm)
+{
+ u16 reg;
+
+ /* If an interrupt is supplied an IRQ enable operation must also be
+ * provided. */
+ BUG_ON(!wm->mach_ops->irq_enable);
+
+ if (request_irq(wm->pen_irq, wm97xx_pen_interrupt,
+ IRQF_SHARED | IRQF_SAMPLE_RANDOM,
+ "wm97xx-pen", wm)) {
+ dev_err(wm->dev,
+ "Failed to register pen down interrupt, polling");
+ wm->pen_irq = 0;
+ return -EINVAL;
+ }
+
+ /* Configure GPIO as interrupt source on WM971x */
+ if (wm->id != WM9705_ID2) {
+ BUG_ON(!wm->mach_ops->irq_gpio);
+ reg = wm97xx_reg_read(wm, AC97_MISC_AFE);
+ wm97xx_reg_write(wm, AC97_MISC_AFE,
+ reg & ~(wm->mach_ops->irq_gpio));
+ reg = wm97xx_reg_read(wm, 0x5a);
+ wm97xx_reg_write(wm, 0x5a, reg & ~0x0001);
+ }
+
+ return 0;
+}
+
+static int wm97xx_read_samples(struct wm97xx *wm)
+{
+ struct wm97xx_data data;
+ int rc;
+
+ mutex_lock(&wm->codec_mutex);
+
+ if (wm->mach_ops && wm->mach_ops->acc_enabled)
+ rc = wm->mach_ops->acc_pen_down(wm);
+ else
+ rc = wm->codec->poll_touch(wm, &data);
+
+ if (rc & RC_PENUP) {
+ if (wm->pen_is_down) {
+ wm->pen_is_down = 0;
+ dev_dbg(wm->dev, "pen up\n");
+ input_report_abs(wm->input_dev, ABS_PRESSURE, 0);
+ input_sync(wm->input_dev);
+ } else if (!(rc & RC_AGAIN)) {
+ /* We need high frequency updates only while
+ * pen is down, the user never will be able to
+ * touch screen faster than a few times per
+ * second... On the other hand, when the user
+ * is actively working with the touchscreen we
+ * don't want to lose the quick response. So we
+ * will slowly increase sleep time after the
+ * pen is up and quicky restore it to ~one task
+ * switch when pen is down again.
+ */
+ if (wm->ts_reader_interval < HZ / 10)
+ wm->ts_reader_interval++;
+ }
+
+ } else if (rc & RC_VALID) {
+ dev_dbg(wm->dev,
+ "pen down: x=%x:%d, y=%x:%d, pressure=%x:%d\n",
+ data.x >> 12, data.x & 0xfff, data.y >> 12,
+ data.y & 0xfff, data.p >> 12, data.p & 0xfff);
+ input_report_abs(wm->input_dev, ABS_X, data.x & 0xfff);
+ input_report_abs(wm->input_dev, ABS_Y, data.y & 0xfff);
+ input_report_abs(wm->input_dev, ABS_PRESSURE, data.p & 0xfff);
+ input_sync(wm->input_dev);
+ wm->pen_is_down = 1;
+ wm->ts_reader_interval = wm->ts_reader_min_interval;
+ } else if (rc & RC_PENDOWN) {
+ dev_dbg(wm->dev, "pen down\n");
+ wm->pen_is_down = 1;
+ wm->ts_reader_interval = wm->ts_reader_min_interval;
+ }
+
+ mutex_unlock(&wm->codec_mutex);
+ return rc;
+}
+
+/*
+* The touchscreen sample reader.
+*/
+static void wm97xx_ts_reader(struct work_struct *work)
+{
+ int rc;
+ struct wm97xx *wm = container_of(work, struct wm97xx, ts_reader.work);
+
+ BUG_ON(!wm->codec);
+
+ do {
+ rc = wm97xx_read_samples(wm);
+ } while (rc & RC_AGAIN);
+
+ if (wm->pen_is_down || !wm->pen_irq)
+ queue_delayed_work(wm->ts_workq, &wm->ts_reader,
+ wm->ts_reader_interval);
+}
+
+/**
+ * wm97xx_ts_input_open - Open the touch screen input device.
+ * @idev: Input device to be opened.
+ *
+ * Called by the input sub system to open a wm97xx touchscreen device.
+ * Starts the touchscreen thread and touch digitiser.
+ */
+static int wm97xx_ts_input_open(struct input_dev *idev)
+{
+ struct wm97xx *wm = input_get_drvdata(idev);
+
+ wm->ts_workq = create_singlethread_workqueue("kwm97xx");
+ if (wm->ts_workq == NULL) {
+ dev_err(wm->dev,
+ "Failed to create workqueue\n");
+ return -EINVAL;
+ }
+
+ /* start digitiser */
+ if (wm->mach_ops && wm->mach_ops->acc_enabled)
+ wm->codec->acc_enable(wm, 1);
+ wm->codec->dig_enable(wm, 1);
+
+ INIT_DELAYED_WORK(&wm->ts_reader, wm97xx_ts_reader);
+ INIT_WORK(&wm->pen_event_work, wm97xx_pen_irq_worker);
+
+ wm->ts_reader_min_interval = HZ >= 100 ? HZ / 100 : 1;
+ if (wm->ts_reader_min_interval < 1)
+ wm->ts_reader_min_interval = 1;
+ wm->ts_reader_interval = wm->ts_reader_min_interval;
+
+ wm->pen_is_down = 0;
+ if (wm->pen_irq)
+ wm97xx_init_pen_irq(wm);
+ else
+ dev_err(wm->dev, "No IRQ specified\n");
+
+ /* If we either don't have an interrupt for pen down events or
+ * failed to acquire it then we need to poll.
+ */
+ if (wm->pen_irq == 0)
+ queue_delayed_work(wm->ts_workq, &wm->ts_reader,
+ wm->ts_reader_interval);
+
+ return 0;
+}
+
+/**
+ * wm97xx_ts_input_close - Close the touch screen input device.
+ * @idev: Input device to be closed.
+ *
+ * Called by the input sub system to close a wm97xx touchscreen
+ * device. Kills the touchscreen thread and stops the touch
+ * digitiser.
+ */
+
+static void wm97xx_ts_input_close(struct input_dev *idev)
+{
+ struct wm97xx *wm = input_get_drvdata(idev);
+ u16 reg;
+
+ if (wm->pen_irq) {
+ /* Return the interrupt to GPIO usage (disabling it) */
+ if (wm->id != WM9705_ID2) {
+ BUG_ON(!wm->mach_ops->irq_gpio);
+ reg = wm97xx_reg_read(wm, AC97_MISC_AFE);
+ wm97xx_reg_write(wm, AC97_MISC_AFE,
+ reg | wm->mach_ops->irq_gpio);
+ }
+
+ free_irq(wm->pen_irq, wm);
+ }
+
+ wm->pen_is_down = 0;
+
+ /* Balance out interrupt disables/enables */
+ if (cancel_work_sync(&wm->pen_event_work))
+ wm->mach_ops->irq_enable(wm, 1);
+
+ /* ts_reader rearms itself so we need to explicitly stop it
+ * before we destroy the workqueue.
+ */
+ cancel_delayed_work_sync(&wm->ts_reader);
+
+ destroy_workqueue(wm->ts_workq);
+
+ /* stop digitiser */
+ wm->codec->dig_enable(wm, 0);
+ if (wm->mach_ops && wm->mach_ops->acc_enabled)
+ wm->codec->acc_enable(wm, 0);
+}
+
+static int wm97xx_probe(struct device *dev)
+{
+ struct wm97xx *wm;
+ int ret = 0, id = 0;
+
+ wm = kzalloc(sizeof(struct wm97xx), GFP_KERNEL);
+ if (!wm)
+ return -ENOMEM;
+ mutex_init(&wm->codec_mutex);
+
+ wm->dev = dev;
+ dev->driver_data = wm;
+ wm->ac97 = to_ac97_t(dev);
+
+ /* check that we have a supported codec */
+ id = wm97xx_reg_read(wm, AC97_VENDOR_ID1);
+ if (id != WM97XX_ID1) {
+ dev_err(dev, "Device with vendor %04x is not a wm97xx\n", id);
+ ret = -ENODEV;
+ goto alloc_err;
+ }
+
+ wm->id = wm97xx_reg_read(wm, AC97_VENDOR_ID2);
+
+ dev_info(wm->dev, "detected a wm97%02x codec\n", wm->id & 0xff);
+
+ switch (wm->id & 0xff) {
+#ifdef CONFIG_TOUCHSCREEN_WM9705
+ case 0x05:
+ wm->codec = &wm9705_codec;
+ break;
+#endif
+#ifdef CONFIG_TOUCHSCREEN_WM9712
+ case 0x12:
+ wm->codec = &wm9712_codec;
+ break;
+#endif
+#ifdef CONFIG_TOUCHSCREEN_WM9713
+ case 0x13:
+ wm->codec = &wm9713_codec;
+ break;
+#endif
+ default:
+ dev_err(wm->dev, "Support for wm97%02x not compiled in.\n",
+ wm->id & 0xff);
+ ret = -ENODEV;
+ goto alloc_err;
+ }
+
+ wm->input_dev = input_allocate_device();
+ if (wm->input_dev == NULL) {
+ ret = -ENOMEM;
+ goto alloc_err;
+ }
+
+ /* set up touch configuration */
+ wm->input_dev->name = "wm97xx touchscreen";
+ wm->input_dev->open = wm97xx_ts_input_open;
+ wm->input_dev->close = wm97xx_ts_input_close;
+ set_bit(EV_ABS, wm->input_dev->evbit);
+ set_bit(ABS_X, wm->input_dev->absbit);
+ set_bit(ABS_Y, wm->input_dev->absbit);
+ set_bit(ABS_PRESSURE, wm->input_dev->absbit);
+ input_set_abs_params(wm->input_dev, ABS_X, abs_x[0], abs_x[1],
+ abs_x[2], 0);
+ input_set_abs_params(wm->input_dev, ABS_Y, abs_y[0], abs_y[1],
+ abs_y[2], 0);
+ input_set_abs_params(wm->input_dev, ABS_PRESSURE, abs_p[0], abs_p[1],
+ abs_p[2], 0);
+ input_set_drvdata(wm->input_dev, wm);
+ wm->input_dev->dev.parent = dev;
+ ret = input_register_device(wm->input_dev);
+ if (ret < 0)
+ goto dev_alloc_err;
+
+ /* set up physical characteristics */
+ wm->codec->phy_init(wm);
+
+ /* load gpio cache */
+ wm->gpio[0] = wm97xx_reg_read(wm, AC97_GPIO_CFG);
+ wm->gpio[1] = wm97xx_reg_read(wm, AC97_GPIO_POLARITY);
+ wm->gpio[2] = wm97xx_reg_read(wm, AC97_GPIO_STICKY);
+ wm->gpio[3] = wm97xx_reg_read(wm, AC97_GPIO_WAKEUP);
+ wm->gpio[4] = wm97xx_reg_read(wm, AC97_GPIO_STATUS);
+ wm->gpio[5] = wm97xx_reg_read(wm, AC97_MISC_AFE);
+
+ /* register our battery device */
+ wm->battery_dev = platform_device_alloc("wm97xx-battery", -1);
+ if (!wm->battery_dev) {
+ ret = -ENOMEM;
+ goto batt_err;
+ }
+ platform_set_drvdata(wm->battery_dev, wm);
+ wm->battery_dev->dev.parent = dev;
+ ret = platform_device_add(wm->battery_dev);
+ if (ret < 0)
+ goto batt_reg_err;
+
+ /* register our extended touch device (for machine specific
+ * extensions) */
+ wm->touch_dev = platform_device_alloc("wm97xx-touch", -1);
+ if (!wm->touch_dev) {
+ ret = -ENOMEM;
+ goto touch_err;
+ }
+ platform_set_drvdata(wm->touch_dev, wm);
+ wm->touch_dev->dev.parent = dev;
+ ret = platform_device_add(wm->touch_dev);
+ if (ret < 0)
+ goto touch_reg_err;
+
+ return ret;
+
+ touch_reg_err:
+ platform_device_put(wm->touch_dev);
+ touch_err:
+ platform_device_unregister(wm->battery_dev);
+ wm->battery_dev = NULL;
+ batt_reg_err:
+ platform_device_put(wm->battery_dev);
+ batt_err:
+ input_unregister_device(wm->input_dev);
+ wm->input_dev = NULL;
+ dev_alloc_err:
+ input_free_device(wm->input_dev);
+ alloc_err:
+ kfree(wm);
+
+ return ret;
+}
+
+static int wm97xx_remove(struct device *dev)
+{
+ struct wm97xx *wm = dev_get_drvdata(dev);
+
+ platform_device_unregister(wm->battery_dev);
+ platform_device_unregister(wm->touch_dev);
+ input_unregister_device(wm->input_dev);
+ kfree(wm);
+
+ return 0;
+}
+
+#ifdef CONFIG_PM
+static int wm97xx_suspend(struct device *dev, pm_message_t state)
+{
+ struct wm97xx *wm = dev_get_drvdata(dev);
+ u16 reg;
+ int suspend_mode;
+
+ if (device_may_wakeup(&wm->input_dev->dev))
+ suspend_mode = wm->suspend_mode;
+ else
+ suspend_mode = 0;
+
+ if (wm->input_dev->users)
+ cancel_delayed_work_sync(&wm->ts_reader);
+
+ /* Power down the digitiser (bypassing the cache for resume) */
+ reg = wm97xx_reg_read(wm, AC97_WM97XX_DIGITISER2);
+ reg &= ~WM97XX_PRP_DET_DIG;
+ if (wm->input_dev->users)
+ reg |= suspend_mode;
+ wm->ac97->bus->ops->write(wm->ac97, AC97_WM97XX_DIGITISER2, reg);
+
+ /* WM9713 has an additional power bit - turn it off if there
+ * are no users or if suspend mode is zero. */
+ if (wm->id == WM9713_ID2 &&
+ (!wm->input_dev->users || !suspend_mode)) {
+ reg = wm97xx_reg_read(wm, AC97_EXTENDED_MID) | 0x8000;
+ wm97xx_reg_write(wm, AC97_EXTENDED_MID, reg);
+ }
+
+ return 0;
+}
+
+static int wm97xx_resume(struct device *dev)
+{
+ struct wm97xx *wm = dev_get_drvdata(dev);
+
+ /* restore digitiser and gpios */
+ if (wm->id == WM9713_ID2) {
+ wm97xx_reg_write(wm, AC97_WM9713_DIG1, wm->dig[0]);
+ wm97xx_reg_write(wm, 0x5a, wm->misc);
+ if (wm->input_dev->users) {
+ u16 reg;
+ reg = wm97xx_reg_read(wm, AC97_EXTENDED_MID) & 0x7fff;
+ wm97xx_reg_write(wm, AC97_EXTENDED_MID, reg);
+ }
+ }
+
+ wm97xx_reg_write(wm, AC97_WM9713_DIG2, wm->dig[1]);
+ wm97xx_reg_write(wm, AC97_WM9713_DIG3, wm->dig[2]);
+
+ wm97xx_reg_write(wm, AC97_GPIO_CFG, wm->gpio[0]);
+ wm97xx_reg_write(wm, AC97_GPIO_POLARITY, wm->gpio[1]);
+ wm97xx_reg_write(wm, AC97_GPIO_STICKY, wm->gpio[2]);
+ wm97xx_reg_write(wm, AC97_GPIO_WAKEUP, wm->gpio[3]);
+ wm97xx_reg_write(wm, AC97_GPIO_STATUS, wm->gpio[4]);
+ wm97xx_reg_write(wm, AC97_MISC_AFE, wm->gpio[5]);
+
+ if (wm->input_dev->users && !wm->pen_irq) {
+ wm->ts_reader_interval = wm->ts_reader_min_interval;
+ queue_delayed_work(wm->ts_workq, &wm->ts_reader,
+ wm->ts_reader_interval);
+ }
+
+ return 0;
+}
+
+#else
+#define wm97xx_suspend NULL
+#define wm97xx_resume NULL
+#endif
+
+/*
+ * Machine specific operations
+ */
+int wm97xx_register_mach_ops(struct wm97xx *wm,
+ struct wm97xx_mach_ops *mach_ops)
+{
+ mutex_lock(&wm->codec_mutex);
+ if (wm->mach_ops) {
+ mutex_unlock(&wm->codec_mutex);
+ return -EINVAL;
+ }
+ wm->mach_ops = mach_ops;
+ mutex_unlock(&wm->codec_mutex);
+
+ return 0;
+}
+EXPORT_SYMBOL_GPL(wm97xx_register_mach_ops);
+
+void wm97xx_unregister_mach_ops(struct wm97xx *wm)
+{
+ mutex_lock(&wm->codec_mutex);
+ wm->mach_ops = NULL;
+ mutex_unlock(&wm->codec_mutex);
+}
+EXPORT_SYMBOL_GPL(wm97xx_unregister_mach_ops);
+
+static struct device_driver wm97xx_driver = {
+ .name = "ac97",
+ .bus = &ac97_bus_type,
+ .owner = THIS_MODULE,
+ .probe = wm97xx_probe,
+ .remove = wm97xx_remove,
+ .suspend = wm97xx_suspend,
+ .resume = wm97xx_resume,
+};
+
+static int __init wm97xx_init(void)
+{
+ return driver_register(&wm97xx_driver);
+}
+
+static void __exit wm97xx_exit(void)
+{
+ driver_unregister(&wm97xx_driver);
+}
+
+module_init(wm97xx_init);
+module_exit(wm97xx_exit);
+
+/* Module information */
+MODULE_AUTHOR("Liam Girdwood <liam.girdwood@wolfsonmicro.com>");
+MODULE_DESCRIPTION("WM97xx Core - Touch Screen / AUX ADC / GPIO Driver");
+MODULE_LICENSE("GPL");
generated by cgit v1.2.3 (git 2.0.4) at 2024-12-27 12:50:33 +0000