diff options
Diffstat (limited to 'drivers/media/video')
| -rw-r--r-- | drivers/media/video/bt8xx/bttv-cards.c | 22 | ||||
| -rw-r--r-- | drivers/media/video/em28xx/em28xx-video.c | 2 |
2 files changed, 12 insertions, 12 deletions
diff --git a/drivers/media/video/bt8xx/bttv-cards.c b/drivers/media/video/bt8xx/bttv-cards.c index dd6a7d68b07f..3162223a2ff5 100644 --- a/drivers/media/video/bt8xx/bttv-cards.c +++ b/drivers/media/video/bt8xx/bttv-cards.c @@ -4709,18 +4709,18 @@ adtvk503_audio(struct bttv *btv, struct video_audio *v, int set) * * The board hardwire Y0 (xpoint) to MUX1 and MUXOUT to Yin. * GPIO pins are wired as: - * GPIO[0:3] - AX[0:3] (xpoint) - P1[0:3] (microcontroler) - * GPIO[4:6] - AY[0:2] (xpoint) - P1[4:6] (microcontroler) - * GPIO[7] - DATA (xpoint) - P1[7] (microcontroler) - * GPIO[8] - - P3[5] (microcontroler) - * GPIO[9] - RESET (xpoint) - P3[6] (microcontroler) - * GPIO[10] - STROBE (xpoint) - P3[7] (microcontroler) - * GPINTR - - P3[4] (microcontroler) + * GPIO[0:3] - AX[0:3] (xpoint) - P1[0:3] (microcontroller) + * GPIO[4:6] - AY[0:2] (xpoint) - P1[4:6] (microcontroller) + * GPIO[7] - DATA (xpoint) - P1[7] (microcontroller) + * GPIO[8] - - P3[5] (microcontroller) + * GPIO[9] - RESET (xpoint) - P3[6] (microcontroller) + * GPIO[10] - STROBE (xpoint) - P3[7] (microcontroller) + * GPINTR - - P3[4] (microcontroller) * - * The microcontroler is a 80C32 like. It should be possible to change xpoint - * configuration either directly (as we are doing) or using the microcontroler + * The microcontroller is a 80C32 like. It should be possible to change xpoint + * configuration either directly (as we are doing) or using the microcontroller * which is also wired to I2C interface. I have no further info on the - * microcontroler features, one would need to disassembly the firmware. + * microcontroller features, one would need to disassembly the firmware. * note: the vendor refused to give any information on this product, all * that stuff was found using a multimeter! :) */ @@ -4788,7 +4788,7 @@ static void tibetCS16_init(struct bttv *btv) * The analog switch is controlled by the "master", but the detection order * of the four BT878A chips is in an order which I just don't understand. * The "master" is actually the second controller to be detected. The - * logic on the board uses logical numbers for the 4 controlers, but + * logic on the board uses logical numbers for the 4 controllers, but * those numbers are different from the detection sequence. When working * with the analog switch, we need to "map" from the detection sequence * over to the board's logical controller number. This mapping sequence diff --git a/drivers/media/video/em28xx/em28xx-video.c b/drivers/media/video/em28xx/em28xx-video.c index b8d5327c438d..e467682aabd7 100644 --- a/drivers/media/video/em28xx/em28xx-video.c +++ b/drivers/media/video/em28xx/em28xx-video.c @@ -907,7 +907,7 @@ static int em28xx_set_fmt(struct em28xx *dev, unsigned int cmd, struct v4l2_form /* stop io in case it is already in progress */ if (dev->stream == STREAM_ON) { - em28xx_videodbg("VIDIOC_SET_FMT: interupting stream\n"); + em28xx_videodbg("VIDIOC_SET_FMT: interrupting stream\n"); if ((ret = em28xx_stream_interrupt(dev))) return ret; } |