diff options
Diffstat (limited to 'drivers/mmc/host')
-rw-r--r-- | drivers/mmc/host/mmci.c | 93 | ||||
-rw-r--r-- | drivers/mmc/host/mmci.h | 3 |
2 files changed, 80 insertions, 16 deletions
diff --git a/drivers/mmc/host/mmci.c b/drivers/mmc/host/mmci.c index ed700a5b03ae..976c9d0e8080 100644 --- a/drivers/mmc/host/mmci.c +++ b/drivers/mmc/host/mmci.c @@ -45,6 +45,10 @@ static unsigned int fmax = 515633; * is asserted (likewise for RX) * @fifohalfsize: number of bytes that can be written when MCI_TXFIFOHALFEMPTY * is asserted (likewise for RX) + * @broken_blockend: the MCI_DATABLOCKEND is broken on the hardware + * and will not work at all. + * @broken_blockend_dma: the MCI_DATABLOCKEND is broken on the hardware when + * using DMA. */ struct variant_data { unsigned int clkreg; @@ -52,6 +56,8 @@ struct variant_data { unsigned int datalength_bits; unsigned int fifosize; unsigned int fifohalfsize; + bool broken_blockend; + bool broken_blockend_dma; }; static struct variant_data variant_arm = { @@ -65,6 +71,7 @@ static struct variant_data variant_u300 = { .fifohalfsize = 8 * 4, .clkreg_enable = 1 << 13, /* HWFCEN */ .datalength_bits = 16, + .broken_blockend_dma = true, }; static struct variant_data variant_ux500 = { @@ -73,6 +80,7 @@ static struct variant_data variant_ux500 = { .clkreg = MCI_CLK_ENABLE, .clkreg_enable = 1 << 14, /* HWFCEN */ .datalength_bits = 24, + .broken_blockend = true, }; /* * This must be called with host->lock held @@ -178,6 +186,8 @@ static void mmci_start_data(struct mmci_host *host, struct mmc_data *data) host->data = data; host->size = data->blksz * data->blocks; host->data_xfered = 0; + host->blockend = false; + host->dataend = false; mmci_init_sg(host, data); @@ -249,20 +259,9 @@ static void mmci_data_irq(struct mmci_host *host, struct mmc_data *data, unsigned int status) { - if (status & MCI_DATABLOCKEND) { - host->data_xfered += data->blksz; -#ifdef CONFIG_ARCH_U300 - /* - * On the U300 some signal or other is - * badly routed so that a data write does - * not properly terminate with a MCI_DATAEND - * status flag. This quirk will make writes - * work again. - */ - if (data->flags & MMC_DATA_WRITE) - status |= MCI_DATAEND; -#endif - } + struct variant_data *variant = host->variant; + + /* First check for errors */ if (status & (MCI_DATACRCFAIL|MCI_DATATIMEOUT|MCI_TXUNDERRUN|MCI_RXOVERRUN)) { dev_dbg(mmc_dev(host->mmc), "MCI ERROR IRQ (status %08x)\n", status); if (status & MCI_DATACRCFAIL) @@ -271,7 +270,10 @@ mmci_data_irq(struct mmci_host *host, struct mmc_data *data, data->error = -ETIMEDOUT; else if (status & (MCI_TXUNDERRUN|MCI_RXOVERRUN)) data->error = -EIO; - status |= MCI_DATAEND; + + /* Force-complete the transaction */ + host->blockend = true; + host->dataend = true; /* * We hit an error condition. Ensure that any data @@ -289,9 +291,64 @@ mmci_data_irq(struct mmci_host *host, struct mmc_data *data, local_irq_restore(flags); } } - if (status & MCI_DATAEND) { + + /* + * On ARM variants in PIO mode, MCI_DATABLOCKEND + * is always sent first, and we increase the + * transfered number of bytes for that IRQ. Then + * MCI_DATAEND follows and we conclude the transaction. + * + * On the Ux500 single-IRQ variant MCI_DATABLOCKEND + * doesn't seem to immediately clear from the status, + * so we can't use it keep count when only one irq is + * used because the irq will hit for other reasons, and + * then the flag is still up. So we use the MCI_DATAEND + * IRQ at the end of the entire transfer because + * MCI_DATABLOCKEND is broken. + * + * In the U300, the IRQs can arrive out-of-order, + * e.g. MCI_DATABLOCKEND sometimes arrives after MCI_DATAEND, + * so for this case we use the flags "blockend" and + * "dataend" to make sure both IRQs have arrived before + * concluding the transaction. (This does not apply + * to the Ux500 which doesn't fire MCI_DATABLOCKEND + * at all.) In DMA mode it suffers from the same problem + * as the Ux500. + */ + if (status & MCI_DATABLOCKEND) { + /* + * Just being a little over-cautious, we do not + * use this progressive update if the hardware blockend + * flag is unreliable: since it can stay high between + * IRQs it will corrupt the transfer counter. + */ + if (!variant->broken_blockend) + host->data_xfered += data->blksz; + host->blockend = true; + } + + if (status & MCI_DATAEND) + host->dataend = true; + + /* + * On variants with broken blockend we shall only wait for dataend, + * on others we must sync with the blockend signal since they can + * appear out-of-order. + */ + if (host->dataend && (host->blockend || variant->broken_blockend)) { mmci_stop_data(host); + /* Reset these flags */ + host->blockend = false; + host->dataend = false; + + /* + * Variants with broken blockend flags need to handle the + * end of the entire transfer here. + */ + if (variant->broken_blockend && !data->error) + host->data_xfered += data->blksz * data->blocks; + if (!data->stop) { mmci_request_end(host, data->mrq); } else { @@ -841,6 +898,10 @@ static int __devinit mmci_probe(struct amba_device *dev, struct amba_id *id) } mask = MCI_IRQENABLE; + /* Don't use the datablockend flag if it's broken */ + if (variant->broken_blockend) + mask &= ~MCI_DATABLOCKEND; + writel(mask, host->base + MMCIMASK0); amba_set_drvdata(dev, mmc); diff --git a/drivers/mmc/host/mmci.h b/drivers/mmc/host/mmci.h index b4e48bde1b4e..df06f01aac89 100644 --- a/drivers/mmc/host/mmci.h +++ b/drivers/mmc/host/mmci.h @@ -177,6 +177,9 @@ struct mmci_host { struct timer_list timer; unsigned int oldstat; + bool blockend; + bool dataend; + /* pio stuff */ struct sg_mapping_iter sg_miter; unsigned int size; |