102 files changed, 8740 insertions, 3399 deletions

diff --git a/drivers/mtd/nand/Kconfig b/drivers/mtd/nand/Kconfig
index 605ec8cce67b..88c7d3b4ff8b 100644
--- a/drivers/mtd/nand/Kconfig
+++ b/drivers/mtd/nand/Kconfig
@@ -1,569 +1,6 @@
-config MTD_NAND_ECC
+config MTD_NAND_CORE
 	tristate
 
-config MTD_NAND_ECC_SMC
-	bool "NAND ECC Smart Media byte order"
-	depends on MTD_NAND_ECC
-	default n
-	help
-	  Software ECC according to the Smart Media Specification.
-	  The original Linux implementation had byte 0 and 1 swapped.
+source "drivers/mtd/nand/onenand/Kconfig"
 
-
-menuconfig MTD_NAND
-	tristate "NAND Device Support"
-	depends on MTD
-	select MTD_NAND_ECC
-	help
-	  This enables support for accessing all type of NAND flash
-	  devices. For further information see
-	  <http://www.linux-mtd.infradead.org/doc/nand.html>.
-
-if MTD_NAND
-
-config MTD_NAND_BCH
-	tristate
-	select BCH
-	depends on MTD_NAND_ECC_BCH
-	default MTD_NAND
-
-config MTD_NAND_ECC_BCH
-	bool "Support software BCH ECC"
-	default n
-	help
-	  This enables support for software BCH error correction. Binary BCH
-	  codes are more powerful and cpu intensive than traditional Hamming
-	  ECC codes. They are used with NAND devices requiring more than 1 bit
-	  of error correction.
-
-config MTD_SM_COMMON
-	tristate
-	default n
-
-config MTD_NAND_DENALI
-	tristate
-
-config MTD_NAND_DENALI_PCI
-        tristate "Support Denali NAND controller on Intel Moorestown"
-	select MTD_NAND_DENALI
-	depends on HAS_DMA && PCI
-        help
-          Enable the driver for NAND flash on Intel Moorestown, using the
-          Denali NAND controller core.
-
-config MTD_NAND_DENALI_DT
-	tristate "Support Denali NAND controller as a DT device"
-	select MTD_NAND_DENALI
-	depends on HAS_DMA && HAVE_CLK && OF
-	help
-	  Enable the driver for NAND flash on platforms using a Denali NAND
-	  controller as a DT device.
-
-config MTD_NAND_GPIO
-	tristate "GPIO assisted NAND Flash driver"
-	depends on GPIOLIB || COMPILE_TEST
-	depends on HAS_IOMEM
-	help
-	  This enables a NAND flash driver where control signals are
-	  connected to GPIO pins, and commands and data are communicated
-	  via a memory mapped interface.
-
-config MTD_NAND_AMS_DELTA
-	tristate "NAND Flash device on Amstrad E3"
-	depends on MACH_AMS_DELTA
-	default y
-	help
-	  Support for NAND flash on Amstrad E3 (Delta).
-
-config MTD_NAND_OMAP2
-	tristate "NAND Flash device on OMAP2, OMAP3, OMAP4 and Keystone"
-	depends on (ARCH_OMAP2PLUS || ARCH_KEYSTONE)
-	help
-          Support for NAND flash on Texas Instruments OMAP2, OMAP3, OMAP4
-	  and Keystone platforms.
-
-config MTD_NAND_OMAP_BCH
-	depends on MTD_NAND_OMAP2
-	bool "Support hardware based BCH error correction"
-	default n
-	select BCH
-	help
-	  This config enables the ELM hardware engine, which can be used to
-	  locate and correct errors when using BCH ECC scheme. This offloads
-	  the cpu from doing ECC error searching and correction. However some
-	  legacy OMAP families like OMAP2xxx, OMAP3xxx do not have ELM engine
-	  so this is optional for them.
-
-config MTD_NAND_OMAP_BCH_BUILD
-	def_tristate MTD_NAND_OMAP2 && MTD_NAND_OMAP_BCH
-
-config MTD_NAND_RICOH
-	tristate "Ricoh xD card reader"
-	default n
-	depends on PCI
-	select MTD_SM_COMMON
-	help
-	  Enable support for Ricoh R5C852 xD card reader
-	  You also need to enable ether
-	  NAND SSFDC (SmartMedia) read only translation layer' or new
-	  expermental, readwrite
-	  'SmartMedia/xD new translation layer'
-
-config MTD_NAND_AU1550
-	tristate "Au1550/1200 NAND support"
-	depends on MIPS_ALCHEMY
-	help
-	  This enables the driver for the NAND flash controller on the
-	  AMD/Alchemy 1550 SOC.
-
-config MTD_NAND_BF5XX
-	tristate "Blackfin on-chip NAND Flash Controller driver"
-	depends on BF54x || BF52x
-	help
-	  This enables the Blackfin on-chip NAND flash controller
-
-	  No board specific support is done by this driver, each board
-	  must advertise a platform_device for the driver to attach.
-
-	  This driver can also be built as a module. If so, the module
-	  will be called bf5xx-nand.
-
-config MTD_NAND_BF5XX_HWECC
-	bool "BF5XX NAND Hardware ECC"
-	default y
-	depends on MTD_NAND_BF5XX
-	help
-	  Enable the use of the BF5XX's internal ECC generator when
-	  using NAND.
-
-config MTD_NAND_BF5XX_BOOTROM_ECC
-	bool "Use Blackfin BootROM ECC Layout"
-	default n
-	depends on MTD_NAND_BF5XX_HWECC
-	help
-	  If you wish to modify NAND pages and allow the Blackfin on-chip
-	  BootROM to boot from them, say Y here.  This is only necessary
-	  if you are booting U-Boot out of NAND and you wish to update
-	  U-Boot from Linux' userspace.  Otherwise, you should say N here.
-
-	  If unsure, say N.
-
-config MTD_NAND_S3C2410
-	tristate "NAND Flash support for Samsung S3C SoCs"
-	depends on ARCH_S3C24XX || ARCH_S3C64XX
-	help
-	  This enables the NAND flash controller on the S3C24xx and S3C64xx
-	  SoCs
-
-	  No board specific support is done by this driver, each board
-	  must advertise a platform_device for the driver to attach.
-
-config MTD_NAND_S3C2410_DEBUG
-	bool "Samsung S3C NAND driver debug"
-	depends on MTD_NAND_S3C2410
-	help
-	  Enable debugging of the S3C NAND driver
-
-config MTD_NAND_NDFC
-	tristate "NDFC NanD Flash Controller"
-	depends on 4xx
-	select MTD_NAND_ECC_SMC
-	help
-	 NDFC Nand Flash Controllers are integrated in IBM/AMCC's 4xx SoCs
-
-config MTD_NAND_S3C2410_CLKSTOP
-	bool "Samsung S3C NAND IDLE clock stop"
-	depends on MTD_NAND_S3C2410
-	default n
-	help
-	  Stop the clock to the NAND controller when there is no chip
-	  selected to save power. This will mean there is a small delay
-	  when the is NAND chip selected or released, but will save
-	  approximately 5mA of power when there is nothing happening.
-
-config MTD_NAND_TANGO
-	tristate "NAND Flash support for Tango chips"
-	depends on ARCH_TANGO || COMPILE_TEST
-	depends on HAS_DMA
-	help
-	  Enables the NAND Flash controller on Tango chips.
-
-config MTD_NAND_DISKONCHIP
-	tristate "DiskOnChip 2000, Millennium and Millennium Plus (NAND reimplementation)"
-	depends on HAS_IOMEM
-	select REED_SOLOMON
-	select REED_SOLOMON_DEC16
-	help
-	  This is a reimplementation of M-Systems DiskOnChip 2000,
-	  Millennium and Millennium Plus as a standard NAND device driver,
-	  as opposed to the earlier self-contained MTD device drivers.
-	  This should enable, among other things, proper JFFS2 operation on
-	  these devices.
-
-config MTD_NAND_DISKONCHIP_PROBE_ADVANCED
-        bool "Advanced detection options for DiskOnChip"
-        depends on MTD_NAND_DISKONCHIP
-        help
-          This option allows you to specify nonstandard address at which to
-          probe for a DiskOnChip, or to change the detection options.  You
-          are unlikely to need any of this unless you are using LinuxBIOS.
-          Say 'N'.
-
-config MTD_NAND_DISKONCHIP_PROBE_ADDRESS
-        hex "Physical address of DiskOnChip" if MTD_NAND_DISKONCHIP_PROBE_ADVANCED
-        depends on MTD_NAND_DISKONCHIP
-        default "0"
-        ---help---
-        By default, the probe for DiskOnChip devices will look for a
-        DiskOnChip at every multiple of 0x2000 between 0xC8000 and 0xEE000.
-        This option allows you to specify a single address at which to probe
-        for the device, which is useful if you have other devices in that
-        range which get upset when they are probed.
-
-        (Note that on PowerPC, the normal probe will only check at
-        0xE4000000.)
-
-        Normally, you should leave this set to zero, to allow the probe at
-        the normal addresses.
-
-config MTD_NAND_DISKONCHIP_PROBE_HIGH
-        bool "Probe high addresses"
-        depends on MTD_NAND_DISKONCHIP_PROBE_ADVANCED
-        help
-          By default, the probe for DiskOnChip devices will look for a
-          DiskOnChip at every multiple of 0x2000 between 0xC8000 and 0xEE000.
-          This option changes to make it probe between 0xFFFC8000 and
-          0xFFFEE000.  Unless you are using LinuxBIOS, this is unlikely to be
-          useful to you.  Say 'N'.
-
-config MTD_NAND_DISKONCHIP_BBTWRITE
-	bool "Allow BBT writes on DiskOnChip Millennium and 2000TSOP"
-	depends on MTD_NAND_DISKONCHIP
-	help
-	  On DiskOnChip devices shipped with the INFTL filesystem (Millennium
-	  and 2000 TSOP/Alon), Linux reserves some space at the end of the
-	  device for the Bad Block Table (BBT).  If you have existing INFTL
-	  data on your device (created by non-Linux tools such as M-Systems'
-	  DOS drivers), your data might overlap the area Linux wants to use for
-	  the BBT.  If this is a concern for you, leave this option disabled and
-	  Linux will not write BBT data into this area.
-	  The downside of leaving this option disabled is that if bad blocks
-	  are detected by Linux, they will not be recorded in the BBT, which
-	  could cause future problems.
-	  Once you enable this option, new filesystems (INFTL or others, created
-	  in Linux or other operating systems) will not use the reserved area.
-	  The only reason not to enable this option is to prevent damage to
-	  preexisting filesystems.
-	  Even if you leave this disabled, you can enable BBT writes at module
-	  load time (assuming you build diskonchip as a module) with the module
-	  parameter "inftl_bbt_write=1".
-
-config MTD_NAND_DOCG4
-	tristate "Support for DiskOnChip G4"
-	depends on HAS_IOMEM
-	select BCH
-	select BITREVERSE
-	help
-	  Support for diskonchip G4 nand flash, found in various smartphones and
-	  PDAs, among them the Palm Treo680, HTC Prophet and Wizard, Toshiba
-	  Portege G900, Asus P526, and O2 XDA Zinc.
-
-	  With this driver you will be able to use UBI and create a ubifs on the
-	  device, so you may wish to consider enabling UBI and UBIFS as well.
-
-	  These devices ship with the Mys/Sandisk SAFTL formatting, for which
-	  there is currently no mtd parser, so you may want to use command line
-	  partitioning to segregate write-protected blocks. On the Treo680, the
-	  first five erase blocks (256KiB each) are write-protected, followed
-	  by the block containing the saftl partition table.  This is probably
-	  typical.
-
-config MTD_NAND_SHARPSL
-	tristate "Support for NAND Flash on Sharp SL Series (C7xx + others)"
-	depends on ARCH_PXA
-
-config MTD_NAND_CAFE
-	tristate "NAND support for OLPC CAFÉ chip"
-	depends on PCI
-	select REED_SOLOMON
-	select REED_SOLOMON_DEC16
-	help
-	  Use NAND flash attached to the CAFÉ chip designed for the OLPC
-	  laptop.
-
-config MTD_NAND_CS553X
-	tristate "NAND support for CS5535/CS5536 (AMD Geode companion chip)"
-	depends on X86_32
-	depends on !UML && HAS_IOMEM
-	help
-	  The CS553x companion chips for the AMD Geode processor
-	  include NAND flash controllers with built-in hardware ECC
-	  capabilities; enabling this option will allow you to use
-	  these. The driver will check the MSRs to verify that the
-	  controller is enabled for NAND, and currently requires that
-	  the controller be in MMIO mode.
-
-	  If you say "m", the module will be called cs553x_nand.
-
-config MTD_NAND_ATMEL
-	tristate "Support for NAND Flash / SmartMedia on AT91"
-	depends on ARCH_AT91
-	select MFD_ATMEL_SMC
-	help
-	  Enables support for NAND Flash / Smart Media Card interface
-	  on Atmel AT91 processors.
-
-config MTD_NAND_MARVELL
-	tristate "NAND controller support on Marvell boards"
-	depends on PXA3xx || ARCH_MMP || PLAT_ORION || ARCH_MVEBU || \
-		   COMPILE_TEST
-	depends on HAS_IOMEM && HAS_DMA
-	help
-	  This enables the NAND flash controller driver for Marvell boards,
-	  including:
-	  - PXA3xx processors (NFCv1)
-	  - 32-bit Armada platforms (XP, 37x, 38x, 39x) (NFCv2)
-	  - 64-bit Aramda platforms (7k, 8k) (NFCv2)
-
-config MTD_NAND_SLC_LPC32XX
-	tristate "NXP LPC32xx SLC Controller"
-	depends on ARCH_LPC32XX
-	help
-	  Enables support for NXP's LPC32XX SLC (i.e. for Single Level Cell
-	  chips) NAND controller. This is the default for the PHYTEC 3250
-	  reference board which contains a NAND256R3A2CZA6 chip.
-
-	  Please check the actual NAND chip connected and its support
-	  by the SLC NAND controller.
-
-config MTD_NAND_MLC_LPC32XX
-	tristate "NXP LPC32xx MLC Controller"
-	depends on ARCH_LPC32XX
-	help
-	  Uses the LPC32XX MLC (i.e. for Multi Level Cell chips) NAND
-	  controller. This is the default for the WORK92105 controller
-	  board.
-
-	  Please check the actual NAND chip connected and its support
-	  by the MLC NAND controller.
-
-config MTD_NAND_CM_X270
-	tristate "Support for NAND Flash on CM-X270 modules"
-	depends on MACH_ARMCORE
-
-config MTD_NAND_PASEMI
-	tristate "NAND support for PA Semi PWRficient"
-	depends on PPC_PASEMI
-	help
-	  Enables support for NAND Flash interface on PA Semi PWRficient
-	  based boards
-
-config MTD_NAND_TMIO
-	tristate "NAND Flash device on Toshiba Mobile IO Controller"
-	depends on MFD_TMIO
-	help
-	  Support for NAND flash connected to a Toshiba Mobile IO
-	  Controller in some PDAs, including the Sharp SL6000x.
-
-config MTD_NAND_NANDSIM
-	tristate "Support for NAND Flash Simulator"
-	help
-	  The simulator may simulate various NAND flash chips for the
-	  MTD nand layer.
-
-config MTD_NAND_GPMI_NAND
-        tristate "GPMI NAND Flash Controller driver"
-        depends on MTD_NAND && MXS_DMA
-        help
-	 Enables NAND Flash support for IMX23, IMX28 or IMX6.
-	 The GPMI controller is very powerful, with the help of BCH
-	 module, it can do the hardware ECC. The GPMI supports several
-	 NAND flashs at the same time.
-
-config MTD_NAND_BRCMNAND
-	tristate "Broadcom STB NAND controller"
-	depends on ARM || ARM64 || MIPS
-	help
-	  Enables the Broadcom NAND controller driver. The controller was
-	  originally designed for Set-Top Box but is used on various BCM7xxx,
-	  BCM3xxx, BCM63xxx, iProc/Cygnus and more.
-
-config MTD_NAND_BCM47XXNFLASH
-	tristate "Support for NAND flash on BCM4706 BCMA bus"
-	depends on BCMA_NFLASH
-	help
-	  BCMA bus can have various flash memories attached, they are
-	  registered by bcma as platform devices. This enables driver for
-	  NAND flash memories. For now only BCM4706 is supported.
-
-config MTD_NAND_PLATFORM
-	tristate "Support for generic platform NAND driver"
-	depends on HAS_IOMEM
-	help
-	  This implements a generic NAND driver for on-SOC platform
-	  devices. You will need to provide platform-specific functions
-	  via platform_data.
-
-config MTD_NAND_ORION
-	tristate "NAND Flash support for Marvell Orion SoC"
-	depends on PLAT_ORION
-	help
-	  This enables the NAND flash controller on Orion machines.
-
-	  No board specific support is done by this driver, each board
-	  must advertise a platform_device for the driver to attach.
-
-config MTD_NAND_OXNAS
-	tristate "NAND Flash support for Oxford Semiconductor SoC"
-	depends on ARCH_OXNAS || COMPILE_TEST
-	depends on HAS_IOMEM
-	help
-	  This enables the NAND flash controller on Oxford Semiconductor SoCs.
-
-config MTD_NAND_FSL_ELBC
-	tristate "NAND support for Freescale eLBC controllers"
-	depends on FSL_SOC
-	select FSL_LBC
-	help
-	  Various Freescale chips, including the 8313, include a NAND Flash
-	  Controller Module with built-in hardware ECC capabilities.
-	  Enabling this option will enable you to use this to control
-	  external NAND devices.
-
-config MTD_NAND_FSL_IFC
-	tristate "NAND support for Freescale IFC controller"
-	depends on FSL_SOC || ARCH_LAYERSCAPE || SOC_LS1021A
-	select FSL_IFC
-	select MEMORY
-	help
-	  Various Freescale chips e.g P1010, include a NAND Flash machine
-	  with built-in hardware ECC capabilities.
-	  Enabling this option will enable you to use this to control
-	  external NAND devices.
-
-config MTD_NAND_FSL_UPM
-	tristate "Support for NAND on Freescale UPM"
-	depends on PPC_83xx || PPC_85xx
-	select FSL_LBC
-	help
-	  Enables support for NAND Flash chips wired onto Freescale PowerPC
-	  processor localbus with User-Programmable Machine support.
-
-config MTD_NAND_MPC5121_NFC
-	tristate "MPC5121 built-in NAND Flash Controller support"
-	depends on PPC_MPC512x
-	help
-	  This enables the driver for the NAND flash controller on the
-	  MPC5121 SoC.
-
-config MTD_NAND_VF610_NFC
-	tristate "Support for Freescale NFC for VF610/MPC5125"
-	depends on (SOC_VF610 || COMPILE_TEST)
-	depends on HAS_IOMEM
-	help
-	  Enables support for NAND Flash Controller on some Freescale
-	  processors like the VF610, MPC5125, MCF54418 or Kinetis K70.
-	  The driver supports a maximum 2k page size. With 2k pages and
-	  64 bytes or more of OOB, hardware ECC with up to 32-bit error
-	  correction is supported. Hardware ECC is only enabled through
-	  device tree.
-
-config MTD_NAND_MXC
-	tristate "MXC NAND support"
-	depends on ARCH_MXC
-	help
-	  This enables the driver for the NAND flash controller on the
-	  MXC processors.
-
-config MTD_NAND_SH_FLCTL
-	tristate "Support for NAND on Renesas SuperH FLCTL"
-	depends on SUPERH || COMPILE_TEST
-	depends on HAS_IOMEM
-	depends on HAS_DMA
-	help
-	  Several Renesas SuperH CPU has FLCTL. This option enables support
-	  for NAND Flash using FLCTL.
-
-config MTD_NAND_DAVINCI
-        tristate "Support NAND on DaVinci/Keystone SoC"
-        depends on ARCH_DAVINCI || (ARCH_KEYSTONE && TI_AEMIF)
-        help
-	  Enable the driver for NAND flash chips on Texas Instruments
-	  DaVinci/Keystone processors.
-
-config MTD_NAND_TXX9NDFMC
-	tristate "NAND Flash support for TXx9 SoC"
-	depends on SOC_TX4938 || SOC_TX4939
-	help
-	  This enables the NAND flash controller on the TXx9 SoCs.
-
-config MTD_NAND_SOCRATES
-	tristate "Support for NAND on Socrates board"
-	depends on SOCRATES
-	help
-	  Enables support for NAND Flash chips wired onto Socrates board.
-
-config MTD_NAND_NUC900
-	tristate "Support for NAND on Nuvoton NUC9xx/w90p910 evaluation boards."
-	depends on ARCH_W90X900
-	help
-	  This enables the driver for the NAND Flash on evaluation board based
-	  on w90p910 / NUC9xx.
-
-config MTD_NAND_JZ4740
-	tristate "Support for JZ4740 SoC NAND controller"
-	depends on MACH_JZ4740
-	help
-		Enables support for NAND Flash on JZ4740 SoC based boards.
-
-config MTD_NAND_JZ4780
-	tristate "Support for NAND on JZ4780 SoC"
-	depends on MACH_JZ4780 && JZ4780_NEMC
-	help
-	  Enables support for NAND Flash connected to the NEMC on JZ4780 SoC
-	  based boards, using the BCH controller for hardware error correction.
-
-config MTD_NAND_FSMC
-	tristate "Support for NAND on ST Micros FSMC"
-	depends on OF
-	depends on PLAT_SPEAR || ARCH_NOMADIK || ARCH_U8500 || MACH_U300
-	help
-	  Enables support for NAND Flash chips on the ST Microelectronics
-	  Flexible Static Memory Controller (FSMC)
-
-config MTD_NAND_XWAY
-	bool "Support for NAND on Lantiq XWAY SoC"
-	depends on LANTIQ && SOC_TYPE_XWAY
-	help
-	  Enables support for NAND Flash chips on Lantiq XWAY SoCs. NAND is attached
-	  to the External Bus Unit (EBU).
-
-config MTD_NAND_SUNXI
-	tristate "Support for NAND on Allwinner SoCs"
-	depends on ARCH_SUNXI
-	help
-	  Enables support for NAND Flash chips on Allwinner SoCs.
-
-config MTD_NAND_HISI504
-	tristate "Support for NAND controller on Hisilicon SoC Hip04"
-	depends on ARCH_HISI || COMPILE_TEST
-	depends on HAS_DMA
-	help
-	  Enables support for NAND controller on Hisilicon SoC Hip04.
-
-config MTD_NAND_QCOM
-	tristate "Support for NAND on QCOM SoCs"
-	depends on ARCH_QCOM
-	help
-	  Enables support for NAND flash chips on SoCs containing the EBI2 NAND
-	  controller. This controller is found on IPQ806x SoC.
-
-config MTD_NAND_MTK
-	tristate "Support for NAND controller on MTK SoCs"
-	depends on ARCH_MEDIATEK || COMPILE_TEST
-	depends on HAS_DMA
-	help
-	  Enables support for NAND controller on MTK SoCs.
-	  This controller is found on mt27xx, mt81xx, mt65xx SoCs.
-
-endif # MTD_NAND
+source "drivers/mtd/nand/raw/Kconfig"
diff --git a/drivers/mtd/nand/Makefile b/drivers/mtd/nand/Makefile
index c882d5ef192a..3f0cb87f1a57 100644
--- a/drivers/mtd/nand/Makefile
+++ b/drivers/mtd/nand/Makefile
@@ -1,70 +1,7 @@
 # SPDX-License-Identifier: GPL-2.0
-#
-# linux/drivers/nand/Makefile
-#
 
-obj-$(CONFIG_MTD_NAND)			+= nand.o
-obj-$(CONFIG_MTD_NAND_ECC)		+= nand_ecc.o
-obj-$(CONFIG_MTD_NAND_BCH)		+= nand_bch.o
-obj-$(CONFIG_MTD_SM_COMMON) 		+= sm_common.o
+nandcore-objs := core.o bbt.o
+obj-$(CONFIG_MTD_NAND_CORE) += nandcore.o
 
-obj-$(CONFIG_MTD_NAND_CAFE)		+= cafe_nand.o
-obj-$(CONFIG_MTD_NAND_AMS_DELTA)	+= ams-delta.o
-obj-$(CONFIG_MTD_NAND_DENALI)		+= denali.o
-obj-$(CONFIG_MTD_NAND_DENALI_PCI)	+= denali_pci.o
-obj-$(CONFIG_MTD_NAND_DENALI_DT)	+= denali_dt.o
-obj-$(CONFIG_MTD_NAND_AU1550)		+= au1550nd.o
-obj-$(CONFIG_MTD_NAND_BF5XX)		+= bf5xx_nand.o
-obj-$(CONFIG_MTD_NAND_S3C2410)		+= s3c2410.o
-obj-$(CONFIG_MTD_NAND_TANGO)		+= tango_nand.o
-obj-$(CONFIG_MTD_NAND_DAVINCI)		+= davinci_nand.o
-obj-$(CONFIG_MTD_NAND_DISKONCHIP)	+= diskonchip.o
-obj-$(CONFIG_MTD_NAND_DOCG4)		+= docg4.o
-obj-$(CONFIG_MTD_NAND_FSMC)		+= fsmc_nand.o
-obj-$(CONFIG_MTD_NAND_SHARPSL)		+= sharpsl.o
-obj-$(CONFIG_MTD_NAND_NANDSIM)		+= nandsim.o
-obj-$(CONFIG_MTD_NAND_CS553X)		+= cs553x_nand.o
-obj-$(CONFIG_MTD_NAND_NDFC)		+= ndfc.o
-obj-$(CONFIG_MTD_NAND_ATMEL)		+= atmel/
-obj-$(CONFIG_MTD_NAND_GPIO)		+= gpio.o
-omap2_nand-objs := omap2.o
-obj-$(CONFIG_MTD_NAND_OMAP2) 		+= omap2_nand.o
-obj-$(CONFIG_MTD_NAND_OMAP_BCH_BUILD)	+= omap_elm.o
-obj-$(CONFIG_MTD_NAND_CM_X270)		+= cmx270_nand.o
-obj-$(CONFIG_MTD_NAND_MARVELL)		+= marvell_nand.o
-obj-$(CONFIG_MTD_NAND_TMIO)		+= tmio_nand.o
-obj-$(CONFIG_MTD_NAND_PLATFORM)		+= plat_nand.o
-obj-$(CONFIG_MTD_NAND_PASEMI)		+= pasemi_nand.o
-obj-$(CONFIG_MTD_NAND_ORION)		+= orion_nand.o
-obj-$(CONFIG_MTD_NAND_OXNAS)		+= oxnas_nand.o
-obj-$(CONFIG_MTD_NAND_FSL_ELBC)		+= fsl_elbc_nand.o
-obj-$(CONFIG_MTD_NAND_FSL_IFC)		+= fsl_ifc_nand.o
-obj-$(CONFIG_MTD_NAND_FSL_UPM)		+= fsl_upm.o
-obj-$(CONFIG_MTD_NAND_SLC_LPC32XX)      += lpc32xx_slc.o
-obj-$(CONFIG_MTD_NAND_MLC_LPC32XX)      += lpc32xx_mlc.o
-obj-$(CONFIG_MTD_NAND_SH_FLCTL)		+= sh_flctl.o
-obj-$(CONFIG_MTD_NAND_MXC)		+= mxc_nand.o
-obj-$(CONFIG_MTD_NAND_SOCRATES)		+= socrates_nand.o
-obj-$(CONFIG_MTD_NAND_TXX9NDFMC)	+= txx9ndfmc.o
-obj-$(CONFIG_MTD_NAND_NUC900)		+= nuc900_nand.o
-obj-$(CONFIG_MTD_NAND_MPC5121_NFC)	+= mpc5121_nfc.o
-obj-$(CONFIG_MTD_NAND_VF610_NFC)	+= vf610_nfc.o
-obj-$(CONFIG_MTD_NAND_RICOH)		+= r852.o
-obj-$(CONFIG_MTD_NAND_JZ4740)		+= jz4740_nand.o
-obj-$(CONFIG_MTD_NAND_JZ4780)		+= jz4780_nand.o jz4780_bch.o
-obj-$(CONFIG_MTD_NAND_GPMI_NAND)	+= gpmi-nand/
-obj-$(CONFIG_MTD_NAND_XWAY)		+= xway_nand.o
-obj-$(CONFIG_MTD_NAND_BCM47XXNFLASH)	+= bcm47xxnflash/
-obj-$(CONFIG_MTD_NAND_SUNXI)		+= sunxi_nand.o
-obj-$(CONFIG_MTD_NAND_HISI504)	        += hisi504_nand.o
-obj-$(CONFIG_MTD_NAND_BRCMNAND)		+= brcmnand/
-obj-$(CONFIG_MTD_NAND_QCOM)		+= qcom_nandc.o
-obj-$(CONFIG_MTD_NAND_MTK)		+= mtk_ecc.o mtk_nand.o
-
-nand-objs := nand_base.o nand_bbt.o nand_timings.o nand_ids.o
-nand-objs += nand_amd.o
-nand-objs += nand_hynix.o
-nand-objs += nand_macronix.o
-nand-objs += nand_micron.o
-nand-objs += nand_samsung.o
-nand-objs += nand_toshiba.o
+obj-y	+= onenand/
+obj-y	+= raw/
diff --git a/drivers/mtd/nand/bbt.c b/drivers/mtd/nand/bbt.c
new file mode 100644
index 000000000000..56cde38b92c0
--- /dev/null
+++ b/drivers/mtd/nand/bbt.c
@@ -0,0 +1,130 @@
+// SPDX-License-Identifier: GPL-2.0
+/*
+ * Copyright (c) 2017 Free Electrons
+ *
+ * Authors:
+ *	Boris Brezillon <boris.brezillon@free-electrons.com>
+ *	Peter Pan <peterpandong@micron.com>
+ */
+
+#define pr_fmt(fmt)	"nand-bbt: " fmt
+
+#include <linux/mtd/nand.h>
+#include <linux/slab.h>
+
+/**
+ * nanddev_bbt_init() - Initialize the BBT (Bad Block Table)
+ * @nand: NAND device
+ *
+ * Initialize the in-memory BBT.
+ *
+ * Return: 0 in case of success, a negative error code otherwise.
+ */
+int nanddev_bbt_init(struct nand_device *nand)
+{
+	unsigned int bits_per_block = fls(NAND_BBT_BLOCK_NUM_STATUS);
+	unsigned int nblocks = nanddev_neraseblocks(nand);
+	unsigned int nwords = DIV_ROUND_UP(nblocks * bits_per_block,
+					   BITS_PER_LONG);
+
+	nand->bbt.cache = kzalloc(nwords, GFP_KERNEL);
+	if (!nand->bbt.cache)
+		return -ENOMEM;
+
+	return 0;
+}
+EXPORT_SYMBOL_GPL(nanddev_bbt_init);
+
+/**
+ * nanddev_bbt_cleanup() - Cleanup the BBT (Bad Block Table)
+ * @nand: NAND device
+ *
+ * Undoes what has been done in nanddev_bbt_init()
+ */
+void nanddev_bbt_cleanup(struct nand_device *nand)
+{
+	kfree(nand->bbt.cache);
+}
+EXPORT_SYMBOL_GPL(nanddev_bbt_cleanup);
+
+/**
+ * nanddev_bbt_update() - Update a BBT
+ * @nand: nand device
+ *
+ * Update the BBT. Currently a NOP function since on-flash bbt is not yet
+ * supported.
+ *
+ * Return: 0 in case of success, a negative error code otherwise.
+ */
+int nanddev_bbt_update(struct nand_device *nand)
+{
+	return 0;
+}
+EXPORT_SYMBOL_GPL(nanddev_bbt_update);
+
+/**
+ * nanddev_bbt_get_block_status() - Return the status of an eraseblock
+ * @nand: nand device
+ * @entry: the BBT entry
+ *
+ * Return: a positive number nand_bbt_block_status status or -%ERANGE if @entry
+ *	   is bigger than the BBT size.
+ */
+int nanddev_bbt_get_block_status(const struct nand_device *nand,
+				 unsigned int entry)
+{
+	unsigned int bits_per_block = fls(NAND_BBT_BLOCK_NUM_STATUS);
+	unsigned long *pos = nand->bbt.cache +
+			     ((entry * bits_per_block) / BITS_PER_LONG);
+	unsigned int offs = (entry * bits_per_block) % BITS_PER_LONG;
+	unsigned long status;
+
+	if (entry >= nanddev_neraseblocks(nand))
+		return -ERANGE;
+
+	status = pos[0] >> offs;
+	if (bits_per_block + offs > BITS_PER_LONG)
+		status |= pos[1] << (BITS_PER_LONG - offs);
+
+	return status & GENMASK(bits_per_block - 1, 0);
+}
+EXPORT_SYMBOL_GPL(nanddev_bbt_get_block_status);
+
+/**
+ * nanddev_bbt_set_block_status() - Update the status of an eraseblock in the
+ *				    in-memory BBT
+ * @nand: nand device
+ * @entry: the BBT entry to update
+ * @status: the new status
+ *
+ * Update an entry of the in-memory BBT. If you want to push the updated BBT
+ * the NAND you should call nanddev_bbt_update().
+ *
+ * Return: 0 in case of success or -%ERANGE if @entry is bigger than the BBT
+ *	   size.
+ */
+int nanddev_bbt_set_block_status(struct nand_device *nand, unsigned int entry,
+				 enum nand_bbt_block_status status)
+{
+	unsigned int bits_per_block = fls(NAND_BBT_BLOCK_NUM_STATUS);
+	unsigned long *pos = nand->bbt.cache +
+			     ((entry * bits_per_block) / BITS_PER_LONG);
+	unsigned int offs = (entry * bits_per_block) % BITS_PER_LONG;
+	unsigned long val = status & GENMASK(bits_per_block - 1, 0);
+
+	if (entry >= nanddev_neraseblocks(nand))
+		return -ERANGE;
+
+	pos[0] &= ~GENMASK(offs + bits_per_block - 1, offs);
+	pos[0] |= val << offs;
+
+	if (bits_per_block + offs > BITS_PER_LONG) {
+		unsigned int rbits = bits_per_block + offs - BITS_PER_LONG;
+
+		pos[1] &= ~GENMASK(rbits - 1, 0);
+		pos[1] |= val >> rbits;
+	}
+
+	return 0;
+}
+EXPORT_SYMBOL_GPL(nanddev_bbt_set_block_status);
diff --git a/drivers/mtd/nand/bf5xx_nand.c b/drivers/mtd/nand/bf5xx_nand.c
deleted file mode 100644
index 87bbd177b3e5..000000000000
--- a/drivers/mtd/nand/bf5xx_nand.c
+++ /dev/null
@@ -1,862 +0,0 @@
-/* linux/drivers/mtd/nand/bf5xx_nand.c
- *
- * Copyright 2006-2008 Analog Devices Inc.
- *	http://blackfin.uclinux.org/
- *	Bryan Wu <bryan.wu@analog.com>
- *
- * Blackfin BF5xx on-chip NAND flash controller driver
- *
- * Derived from drivers/mtd/nand/s3c2410.c
- * Copyright (c) 2007 Ben Dooks <ben@simtec.co.uk>
- *
- * Derived from drivers/mtd/nand/cafe.c
- * Copyright © 2006 Red Hat, Inc.
- * Copyright © 2006 David Woodhouse <dwmw2@infradead.org>
- *
- * Changelog:
- *	12-Jun-2007  Bryan Wu:  Initial version
- *	18-Jul-2007  Bryan Wu:
- *		- ECC_HW and ECC_SW supported
- *		- DMA supported in ECC_HW
- *		- YAFFS tested as rootfs in both ECC_HW and ECC_SW
- *
- * This program is free software; you can redistribute it and/or modify
- * it under the terms of the GNU General Public License as published by
- * the Free Software Foundation; either version 2 of the License, or
- * (at your option) any later version.
- *
- * This program is distributed in the hope that it will be useful,
- * but WITHOUT ANY WARRANTY; without even the implied warranty of
- * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
- * GNU General Public License for more details.
- *
- * You should have received a copy of the GNU General Public License
- * along with this program; if not, write to the Free Software
- * Foundation, Inc., 59 Temple Place, Suite 330, Boston, MA  02111-1307  USA
-*/
-
-#include <linux/module.h>
-#include <linux/types.h>
-#include <linux/kernel.h>
-#include <linux/string.h>
-#include <linux/ioport.h>
-#include <linux/platform_device.h>
-#include <linux/delay.h>
-#include <linux/dma-mapping.h>
-#include <linux/err.h>
-#include <linux/slab.h>
-#include <linux/io.h>
-#include <linux/bitops.h>
-
-#include <linux/mtd/mtd.h>
-#include <linux/mtd/rawnand.h>
-#include <linux/mtd/nand_ecc.h>
-#include <linux/mtd/partitions.h>
-
-#include <asm/blackfin.h>
-#include <asm/dma.h>
-#include <asm/cacheflush.h>
-#include <asm/nand.h>
-#include <asm/portmux.h>
-
-#define DRV_NAME	"bf5xx-nand"
-#define DRV_VERSION	"1.2"
-#define DRV_AUTHOR	"Bryan Wu <bryan.wu@analog.com>"
-#define DRV_DESC	"BF5xx on-chip NAND FLash Controller Driver"
-
-/* NFC_STAT Masks */
-#define NBUSY       0x01  /* Not Busy */
-#define WB_FULL     0x02  /* Write Buffer Full */
-#define PG_WR_STAT  0x04  /* Page Write Pending */
-#define PG_RD_STAT  0x08  /* Page Read Pending */
-#define WB_EMPTY    0x10  /* Write Buffer Empty */
-
-/* NFC_IRQSTAT Masks */
-#define NBUSYIRQ    0x01  /* Not Busy IRQ */
-#define WB_OVF      0x02  /* Write Buffer Overflow */
-#define WB_EDGE     0x04  /* Write Buffer Edge Detect */
-#define RD_RDY      0x08  /* Read Data Ready */
-#define WR_DONE     0x10  /* Page Write Done */
-
-/* NFC_RST Masks */
-#define ECC_RST     0x01  /* ECC (and NFC counters) Reset */
-
-/* NFC_PGCTL Masks */
-#define PG_RD_START 0x01  /* Page Read Start */
-#define PG_WR_START 0x02  /* Page Write Start */
-
-#ifdef CONFIG_MTD_NAND_BF5XX_HWECC
-static int hardware_ecc = 1;
-#else
-static int hardware_ecc;
-#endif
-
-static const unsigned short bfin_nfc_pin_req[] =
-	{P_NAND_CE,
-	 P_NAND_RB,
-	 P_NAND_D0,
-	 P_NAND_D1,
-	 P_NAND_D2,
-	 P_NAND_D3,
-	 P_NAND_D4,
-	 P_NAND_D5,
-	 P_NAND_D6,
-	 P_NAND_D7,
-	 P_NAND_WE,
-	 P_NAND_RE,
-	 P_NAND_CLE,
-	 P_NAND_ALE,
-	 0};
-
-#ifdef CONFIG_MTD_NAND_BF5XX_BOOTROM_ECC
-static int bootrom_ooblayout_ecc(struct mtd_info *mtd, int section,
-				 struct mtd_oob_region *oobregion)
-{
-	if (section > 7)
-		return -ERANGE;
-
-	oobregion->offset = section * 8;
-	oobregion->length = 3;
-
-	return 0;
-}
-
-static int bootrom_ooblayout_free(struct mtd_info *mtd, int section,
-				  struct mtd_oob_region *oobregion)
-{
-	if (section > 7)
-		return -ERANGE;
-
-	oobregion->offset = (section * 8) + 3;
-	oobregion->length = 5;
-
-	return 0;
-}
-
-static const struct mtd_ooblayout_ops bootrom_ooblayout_ops = {
-	.ecc = bootrom_ooblayout_ecc,
-	.free = bootrom_ooblayout_free,
-};
-#endif
-
-/*
- * Data structures for bf5xx nand flash controller driver
- */
-
-/* bf5xx nand info */
-struct bf5xx_nand_info {
-	/* mtd info */
-	struct nand_hw_control		controller;
-	struct nand_chip		chip;
-
-	/* platform info */
-	struct bf5xx_nand_platform	*platform;
-
-	/* device info */
-	struct device			*device;
-
-	/* DMA stuff */
-	struct completion		dma_completion;
-};
-
-/*
- * Conversion functions
- */
-static struct bf5xx_nand_info *mtd_to_nand_info(struct mtd_info *mtd)
-{
-	return container_of(mtd_to_nand(mtd), struct bf5xx_nand_info,
-			    chip);
-}
-
-static struct bf5xx_nand_info *to_nand_info(struct platform_device *pdev)
-{
-	return platform_get_drvdata(pdev);
-}
-
-static struct bf5xx_nand_platform *to_nand_plat(struct platform_device *pdev)
-{
-	return dev_get_platdata(&pdev->dev);
-}
-
-/*
- * struct nand_chip interface function pointers
- */
-
-/*
- * bf5xx_nand_hwcontrol
- *
- * Issue command and address cycles to the chip
- */
-static void bf5xx_nand_hwcontrol(struct mtd_info *mtd, int cmd,
-				   unsigned int ctrl)
-{
-	if (cmd == NAND_CMD_NONE)
-		return;
-
-	while (bfin_read_NFC_STAT() & WB_FULL)
-		cpu_relax();
-
-	if (ctrl & NAND_CLE)
-		bfin_write_NFC_CMD(cmd);
-	else if (ctrl & NAND_ALE)
-		bfin_write_NFC_ADDR(cmd);
-	SSYNC();
-}
-
-/*
- * bf5xx_nand_devready()
- *
- * returns 0 if the nand is busy, 1 if it is ready
- */
-static int bf5xx_nand_devready(struct mtd_info *mtd)
-{
-	unsigned short val = bfin_read_NFC_STAT();
-
-	if ((val & NBUSY) == NBUSY)
-		return 1;
-	else
-		return 0;
-}
-
-/*
- * ECC functions
- * These allow the bf5xx to use the controller's ECC
- * generator block to ECC the data as it passes through
- */
-
-/*
- * ECC error correction function
- */
-static int bf5xx_nand_correct_data_256(struct mtd_info *mtd, u_char *dat,
-					u_char *read_ecc, u_char *calc_ecc)
-{
-	struct bf5xx_nand_info *info = mtd_to_nand_info(mtd);
-	u32 syndrome[5];
-	u32 calced, stored;
-	int i;
-	unsigned short failing_bit, failing_byte;
-	u_char data;
-
-	calced = calc_ecc[0] | (calc_ecc[1] << 8) | (calc_ecc[2] << 16);
-	stored = read_ecc[0] | (read_ecc[1] << 8) | (read_ecc[2] << 16);
-
-	syndrome[0] = (calced ^ stored);
-
-	/*
-	 * syndrome 0: all zero
-	 * No error in data
-	 * No action
-	 */
-	if (!syndrome[0] || !calced || !stored)
-		return 0;
-
-	/*
-	 * sysdrome 0: only one bit is one
-	 * ECC data was incorrect
-	 * No action
-	 */
-	if (hweight32(syndrome[0]) == 1) {
-		dev_err(info->device, "ECC data was incorrect!\n");
-		return -EBADMSG;
-	}
-
-	syndrome[1] = (calced & 0x7FF) ^ (stored & 0x7FF);
-	syndrome[2] = (calced & 0x7FF) ^ ((calced >> 11) & 0x7FF);
-	syndrome[3] = (stored & 0x7FF) ^ ((stored >> 11) & 0x7FF);
-	syndrome[4] = syndrome[2] ^ syndrome[3];
-
-	for (i = 0; i < 5; i++)
-		dev_info(info->device, "syndrome[%d] 0x%08x\n", i, syndrome[i]);
-
-	dev_info(info->device,
-		"calced[0x%08x], stored[0x%08x]\n",
-		calced, stored);
-
-	/*
-	 * sysdrome 0: exactly 11 bits are one, each parity
-	 * and parity' pair is 1 & 0 or 0 & 1.
-	 * 1-bit correctable error
-	 * Correct the error
-	 */
-	if (hweight32(syndrome[0]) == 11 && syndrome[4] == 0x7FF) {
-		dev_info(info->device,
-			"1-bit correctable error, correct it.\n");
-		dev_info(info->device,
-			"syndrome[1] 0x%08x\n", syndrome[1]);
-
-		failing_bit = syndrome[1] & 0x7;
-		failing_byte = syndrome[1] >> 0x3;
-		data = *(dat + failing_byte);
-		data = data ^ (0x1 << failing_bit);
-		*(dat + failing_byte) = data;
-
-		return 1;
-	}
-
-	/*
-	 * sysdrome 0: random data
-	 * More than 1-bit error, non-correctable error
-	 * Discard data, mark bad block
-	 */
-	dev_err(info->device,
-		"More than 1-bit error, non-correctable error.\n");
-	dev_err(info->device,
-		"Please discard data, mark bad block\n");
-
-	return -EBADMSG;
-}
-
-static int bf5xx_nand_correct_data(struct mtd_info *mtd, u_char *dat,
-					u_char *read_ecc, u_char *calc_ecc)
-{
-	struct nand_chip *chip = mtd_to_nand(mtd);
-	int ret, bitflips = 0;
-
-	ret = bf5xx_nand_correct_data_256(mtd, dat, read_ecc, calc_ecc);
-	if (ret < 0)
-		return ret;
-
-	bitflips = ret;
-
-	/* If ecc size is 512, correct second 256 bytes */
-	if (chip->ecc.size == 512) {
-		dat += 256;
-		read_ecc += 3;
-		calc_ecc += 3;
-		ret = bf5xx_nand_correct_data_256(mtd, dat, read_ecc, calc_ecc);
-		if (ret < 0)
-			return ret;
-
-		bitflips += ret;
-	}
-
-	return bitflips;
-}
-
-static void bf5xx_nand_enable_hwecc(struct mtd_info *mtd, int mode)
-{
-	return;
-}
-
-static int bf5xx_nand_calculate_ecc(struct mtd_info *mtd,
-		const u_char *dat, u_char *ecc_code)
-{
-	struct bf5xx_nand_info *info = mtd_to_nand_info(mtd);
-	struct nand_chip *chip = mtd_to_nand(mtd);
-	u16 ecc0, ecc1;
-	u32 code[2];
-	u8 *p;
-
-	/* first 3 bytes ECC code for 256 page size */
-	ecc0 = bfin_read_NFC_ECC0();
-	ecc1 = bfin_read_NFC_ECC1();
-
-	code[0] = (ecc0 & 0x7ff) | ((ecc1 & 0x7ff) << 11);
-
-	dev_dbg(info->device, "returning ecc 0x%08x\n", code[0]);
-
-	p = (u8 *) code;
-	memcpy(ecc_code, p, 3);
-
-	/* second 3 bytes ECC code for 512 ecc size */
-	if (chip->ecc.size == 512) {
-		ecc0 = bfin_read_NFC_ECC2();
-		ecc1 = bfin_read_NFC_ECC3();
-		code[1] = (ecc0 & 0x7ff) | ((ecc1 & 0x7ff) << 11);
-
-		/* second 3 bytes in ecc_code for second 256
-		 * bytes of 512 page size
-		 */
-		p = (u8 *) (code + 1);
-		memcpy((ecc_code + 3), p, 3);
-		dev_dbg(info->device, "returning ecc 0x%08x\n", code[1]);
-	}
-
-	return 0;
-}
-
-/*
- * PIO mode for buffer writing and reading
- */
-static void bf5xx_nand_read_buf(struct mtd_info *mtd, uint8_t *buf, int len)
-{
-	int i;
-	unsigned short val;
-
-	/*
-	 * Data reads are requested by first writing to NFC_DATA_RD
-	 * and then reading back from NFC_READ.
-	 */
-	for (i = 0; i < len; i++) {
-		while (bfin_read_NFC_STAT() & WB_FULL)
-			cpu_relax();
-
-		/* Contents do not matter */
-		bfin_write_NFC_DATA_RD(0x0000);
-		SSYNC();
-
-		while ((bfin_read_NFC_IRQSTAT() & RD_RDY) != RD_RDY)
-			cpu_relax();
-
-		buf[i] = bfin_read_NFC_READ();
-
-		val = bfin_read_NFC_IRQSTAT();
-		val |= RD_RDY;
-		bfin_write_NFC_IRQSTAT(val);
-		SSYNC();
-	}
-}
-
-static uint8_t bf5xx_nand_read_byte(struct mtd_info *mtd)
-{
-	uint8_t val;
-
-	bf5xx_nand_read_buf(mtd, &val, 1);
-
-	return val;
-}
-
-static void bf5xx_nand_write_buf(struct mtd_info *mtd,
-				const uint8_t *buf, int len)
-{
-	int i;
-
-	for (i = 0; i < len; i++) {
-		while (bfin_read_NFC_STAT() & WB_FULL)
-			cpu_relax();
-
-		bfin_write_NFC_DATA_WR(buf[i]);
-		SSYNC();
-	}
-}
-
-static void bf5xx_nand_read_buf16(struct mtd_info *mtd, uint8_t *buf, int len)
-{
-	int i;
-	u16 *p = (u16 *) buf;
-	len >>= 1;
-
-	/*
-	 * Data reads are requested by first writing to NFC_DATA_RD
-	 * and then reading back from NFC_READ.
-	 */
-	bfin_write_NFC_DATA_RD(0x5555);
-
-	SSYNC();
-
-	for (i = 0; i < len; i++)
-		p[i] = bfin_read_NFC_READ();
-}
-
-static void bf5xx_nand_write_buf16(struct mtd_info *mtd,
-				const uint8_t *buf, int len)
-{
-	int i;
-	u16 *p = (u16 *) buf;
-	len >>= 1;
-
-	for (i = 0; i < len; i++)
-		bfin_write_NFC_DATA_WR(p[i]);
-
-	SSYNC();
-}
-
-/*
- * DMA functions for buffer writing and reading
- */
-static irqreturn_t bf5xx_nand_dma_irq(int irq, void *dev_id)
-{
-	struct bf5xx_nand_info *info = dev_id;
-
-	clear_dma_irqstat(CH_NFC);
-	disable_dma(CH_NFC);
-	complete(&info->dma_completion);
-
-	return IRQ_HANDLED;
-}
-
-static void bf5xx_nand_dma_rw(struct mtd_info *mtd,
-				uint8_t *buf, int is_read)
-{
-	struct bf5xx_nand_info *info = mtd_to_nand_info(mtd);
-	struct nand_chip *chip = mtd_to_nand(mtd);
-	unsigned short val;
-
-	dev_dbg(info->device, " mtd->%p, buf->%p, is_read %d\n",
-			mtd, buf, is_read);
-
-	/*
-	 * Before starting a dma transfer, be sure to invalidate/flush
-	 * the cache over the address range of your DMA buffer to
-	 * prevent cache coherency problems. Otherwise very subtle bugs
-	 * can be introduced to your driver.
-	 */
-	if (is_read)
-		invalidate_dcache_range((unsigned int)buf,
-				(unsigned int)(buf + chip->ecc.size));
-	else
-		flush_dcache_range((unsigned int)buf,
-				(unsigned int)(buf + chip->ecc.size));
-
-	/*
-	 * This register must be written before each page is
-	 * transferred to generate the correct ECC register
-	 * values.
-	 */
-	bfin_write_NFC_RST(ECC_RST);
-	SSYNC();
-	while (bfin_read_NFC_RST() & ECC_RST)
-		cpu_relax();
-
-	disable_dma(CH_NFC);
-	clear_dma_irqstat(CH_NFC);
-
-	/* setup DMA register with Blackfin DMA API */
-	set_dma_config(CH_NFC, 0x0);
-	set_dma_start_addr(CH_NFC, (unsigned long) buf);
-
-	/* The DMAs have different size on BF52x and BF54x */
-#ifdef CONFIG_BF52x
-	set_dma_x_count(CH_NFC, (chip->ecc.size >> 1));
-	set_dma_x_modify(CH_NFC, 2);
-	val = DI_EN | WDSIZE_16;
-#endif
-
-#ifdef CONFIG_BF54x
-	set_dma_x_count(CH_NFC, (chip->ecc.size >> 2));
-	set_dma_x_modify(CH_NFC, 4);
-	val = DI_EN | WDSIZE_32;
-#endif
-	/* setup write or read operation */
-	if (is_read)
-		val |= WNR;
-	set_dma_config(CH_NFC, val);
-	enable_dma(CH_NFC);
-
-	/* Start PAGE read/write operation */
-	if (is_read)
-		bfin_write_NFC_PGCTL(PG_RD_START);
-	else
-		bfin_write_NFC_PGCTL(PG_WR_START);
-	wait_for_completion(&info->dma_completion);
-}
-
-static void bf5xx_nand_dma_read_buf(struct mtd_info *mtd,
-					uint8_t *buf, int len)
-{
-	struct bf5xx_nand_info *info = mtd_to_nand_info(mtd);
-	struct nand_chip *chip = mtd_to_nand(mtd);
-
-	dev_dbg(info->device, "mtd->%p, buf->%p, int %d\n", mtd, buf, len);
-
-	if (len == chip->ecc.size)
-		bf5xx_nand_dma_rw(mtd, buf, 1);
-	else
-		bf5xx_nand_read_buf(mtd, buf, len);
-}
-
-static void bf5xx_nand_dma_write_buf(struct mtd_info *mtd,
-				const uint8_t *buf, int len)
-{
-	struct bf5xx_nand_info *info = mtd_to_nand_info(mtd);
-	struct nand_chip *chip = mtd_to_nand(mtd);
-
-	dev_dbg(info->device, "mtd->%p, buf->%p, len %d\n", mtd, buf, len);
-
-	if (len == chip->ecc.size)
-		bf5xx_nand_dma_rw(mtd, (uint8_t *)buf, 0);
-	else
-		bf5xx_nand_write_buf(mtd, buf, len);
-}
-
-static int bf5xx_nand_read_page_raw(struct mtd_info *mtd, struct nand_chip *chip,
-		uint8_t *buf, int oob_required, int page)
-{
-	nand_read_page_op(chip, page, 0, NULL, 0);
-
-	bf5xx_nand_read_buf(mtd, buf, mtd->writesize);
-	bf5xx_nand_read_buf(mtd, chip->oob_poi, mtd->oobsize);
-
-	return 0;
-}
-
-static int bf5xx_nand_write_page_raw(struct mtd_info *mtd,
-		struct nand_chip *chip,	const uint8_t *buf, int oob_required,
-		int page)
-{
-	nand_prog_page_begin_op(chip, page, 0, buf, mtd->writesize);
-	bf5xx_nand_write_buf(mtd, chip->oob_poi, mtd->oobsize);
-
-	return nand_prog_page_end_op(chip);
-}
-
-/*
- * System initialization functions
- */
-static int bf5xx_nand_dma_init(struct bf5xx_nand_info *info)
-{
-	int ret;
-
-	/* Do not use dma */
-	if (!hardware_ecc)
-		return 0;
-
-	init_completion(&info->dma_completion);
-
-	/* Request NFC DMA channel */
-	ret = request_dma(CH_NFC, "BF5XX NFC driver");
-	if (ret < 0) {
-		dev_err(info->device, " unable to get DMA channel\n");
-		return ret;
-	}
-
-#ifdef CONFIG_BF54x
-	/* Setup DMAC1 channel mux for NFC which shared with SDH */
-	bfin_write_DMAC1_PERIMUX(bfin_read_DMAC1_PERIMUX() & ~1);
-	SSYNC();
-#endif
-
-	set_dma_callback(CH_NFC, bf5xx_nand_dma_irq, info);
-
-	/* Turn off the DMA channel first */
-	disable_dma(CH_NFC);
-	return 0;
-}
-
-static void bf5xx_nand_dma_remove(struct bf5xx_nand_info *info)
-{
-	/* Free NFC DMA channel */
-	if (hardware_ecc)
-		free_dma(CH_NFC);
-}
-
-/*
- * BF5XX NFC hardware initialization
- *  - pin mux setup
- *  - clear interrupt status
- */
-static int bf5xx_nand_hw_init(struct bf5xx_nand_info *info)
-{
-	int err = 0;
-	unsigned short val;
-	struct bf5xx_nand_platform *plat = info->platform;
-
-	/* setup NFC_CTL register */
-	dev_info(info->device,
-		"data_width=%d, wr_dly=%d, rd_dly=%d\n",
-		(plat->data_width ? 16 : 8),
-		plat->wr_dly, plat->rd_dly);
-
-	val = (1 << NFC_PG_SIZE_OFFSET) |
-		(plat->data_width << NFC_NWIDTH_OFFSET) |
-		(plat->rd_dly << NFC_RDDLY_OFFSET) |
-		(plat->wr_dly << NFC_WRDLY_OFFSET);
-	dev_dbg(info->device, "NFC_CTL is 0x%04x\n", val);
-
-	bfin_write_NFC_CTL(val);
-	SSYNC();
-
-	/* clear interrupt status */
-	bfin_write_NFC_IRQMASK(0x0);
-	SSYNC();
-	val = bfin_read_NFC_IRQSTAT();
-	bfin_write_NFC_IRQSTAT(val);
-	SSYNC();
-
-	/* DMA initialization  */
-	if (bf5xx_nand_dma_init(info))
-		err = -ENXIO;
-
-	return err;
-}
-
-/*
- * Device management interface
- */
-static int bf5xx_nand_add_partition(struct bf5xx_nand_info *info)
-{
-	struct mtd_info *mtd = nand_to_mtd(&info->chip);
-	struct mtd_partition *parts = info->platform->partitions;
-	int nr = info->platform->nr_partitions;
-
-	return mtd_device_register(mtd, parts, nr);
-}
-
-static int bf5xx_nand_remove(struct platform_device *pdev)
-{
-	struct bf5xx_nand_info *info = to_nand_info(pdev);
-
-	/* first thing we need to do is release all our mtds
-	 * and their partitions, then go through freeing the
-	 * resources used
-	 */
-	nand_release(nand_to_mtd(&info->chip));
-
-	peripheral_free_list(bfin_nfc_pin_req);
-	bf5xx_nand_dma_remove(info);
-
-	return 0;
-}
-
-static int bf5xx_nand_scan(struct mtd_info *mtd)
-{
-	struct nand_chip *chip = mtd_to_nand(mtd);
-	int ret;
-
-	ret = nand_scan_ident(mtd, 1, NULL);
-	if (ret)
-		return ret;
-
-	if (hardware_ecc) {
-		/*
-		 * for nand with page size > 512B, think it as several sections with 512B
-		 */
-		if (likely(mtd->writesize >= 512)) {
-			chip->ecc.size = 512;
-			chip->ecc.bytes = 6;
-			chip->ecc.strength = 2;
-		} else {
-			chip->ecc.size = 256;
-			chip->ecc.bytes = 3;
-			chip->ecc.strength = 1;
-			bfin_write_NFC_CTL(bfin_read_NFC_CTL() & ~(1 << NFC_PG_SIZE_OFFSET));
-			SSYNC();
-		}
-	}
-
-	return	nand_scan_tail(mtd);
-}
-
-/*
- * bf5xx_nand_probe
- *
- * called by device layer when it finds a device matching
- * one our driver can handled. This code checks to see if
- * it can allocate all necessary resources then calls the
- * nand layer to look for devices
- */
-static int bf5xx_nand_probe(struct platform_device *pdev)
-{
-	struct bf5xx_nand_platform *plat = to_nand_plat(pdev);
-	struct bf5xx_nand_info *info = NULL;
-	struct nand_chip *chip = NULL;
-	struct mtd_info *mtd = NULL;
-	int err = 0;
-
-	dev_dbg(&pdev->dev, "(%p)\n", pdev);
-
-	if (!plat) {
-		dev_err(&pdev->dev, "no platform specific information\n");
-		return -EINVAL;
-	}
-
-	if (peripheral_request_list(bfin_nfc_pin_req, DRV_NAME)) {
-		dev_err(&pdev->dev, "requesting Peripherals failed\n");
-		return -EFAULT;
-	}
-
-	info = devm_kzalloc(&pdev->dev, sizeof(*info), GFP_KERNEL);
-	if (info == NULL) {
-		err = -ENOMEM;
-		goto out_err;
-	}
-
-	platform_set_drvdata(pdev, info);
-
-	nand_hw_control_init(&info->controller);
-
-	info->device     = &pdev->dev;
-	info->platform   = plat;
-
-	/* initialise chip data struct */
-	chip = &info->chip;
-	mtd = nand_to_mtd(&info->chip);
-
-	if (plat->data_width)
-		chip->options |= NAND_BUSWIDTH_16;
-
-	chip->options |= NAND_CACHEPRG | NAND_SKIP_BBTSCAN;
-
-	chip->read_buf = (plat->data_width) ?
-		bf5xx_nand_read_buf16 : bf5xx_nand_read_buf;
-	chip->write_buf = (plat->data_width) ?
-		bf5xx_nand_write_buf16 : bf5xx_nand_write_buf;
-
-	chip->read_byte    = bf5xx_nand_read_byte;
-
-	chip->cmd_ctrl     = bf5xx_nand_hwcontrol;
-	chip->dev_ready    = bf5xx_nand_devready;
-
-	nand_set_controller_data(chip, mtd);
-	chip->controller   = &info->controller;
-
-	chip->IO_ADDR_R    = (void __iomem *) NFC_READ;
-	chip->IO_ADDR_W    = (void __iomem *) NFC_DATA_WR;
-
-	chip->chip_delay   = 0;
-
-	/* initialise mtd info data struct */
-	mtd->dev.parent = &pdev->dev;
-
-	/* initialise the hardware */
-	err = bf5xx_nand_hw_init(info);
-	if (err)
-		goto out_err;
-
-	/* setup hardware ECC data struct */
-	if (hardware_ecc) {
-#ifdef CONFIG_MTD_NAND_BF5XX_BOOTROM_ECC
-		mtd_set_ooblayout(mtd, &bootrom_ooblayout_ops);
-#endif
-		chip->read_buf      = bf5xx_nand_dma_read_buf;
-		chip->write_buf     = bf5xx_nand_dma_write_buf;
-		chip->ecc.calculate = bf5xx_nand_calculate_ecc;
-		chip->ecc.correct   = bf5xx_nand_correct_data;
-		chip->ecc.mode	    = NAND_ECC_HW;
-		chip->ecc.hwctl	    = bf5xx_nand_enable_hwecc;
-		chip->ecc.read_page_raw = bf5xx_nand_read_page_raw;
-		chip->ecc.write_page_raw = bf5xx_nand_write_page_raw;
-	} else {
-		chip->ecc.mode	    = NAND_ECC_SOFT;
-		chip->ecc.algo	= NAND_ECC_HAMMING;
-	}
-
-	/* scan hardware nand chip and setup mtd info data struct */
-	if (bf5xx_nand_scan(mtd)) {
-		err = -ENXIO;
-		goto out_err_nand_scan;
-	}
-
-#ifdef CONFIG_MTD_NAND_BF5XX_BOOTROM_ECC
-	chip->badblockpos = 63;
-#endif
-
-	/* add NAND partition */
-	bf5xx_nand_add_partition(info);
-
-	dev_dbg(&pdev->dev, "initialised ok\n");
-	return 0;
-
-out_err_nand_scan:
-	bf5xx_nand_dma_remove(info);
-out_err:
-	peripheral_free_list(bfin_nfc_pin_req);
-
-	return err;
-}
-
-/* driver device registration */
-static struct platform_driver bf5xx_nand_driver = {
-	.probe		= bf5xx_nand_probe,
-	.remove		= bf5xx_nand_remove,
-	.driver		= {
-		.name	= DRV_NAME,
-	},
-};
-
-module_platform_driver(bf5xx_nand_driver);
-
-MODULE_LICENSE("GPL");
-MODULE_AUTHOR(DRV_AUTHOR);
-MODULE_DESCRIPTION(DRV_DESC);
-MODULE_ALIAS("platform:" DRV_NAME);
diff --git a/drivers/mtd/nand/core.c b/drivers/mtd/nand/core.c
new file mode 100644
index 000000000000..d0cd6f8635d7
--- /dev/null
+++ b/drivers/mtd/nand/core.c
@@ -0,0 +1,244 @@
+// SPDX-License-Identifier: GPL-2.0
+/*
+ * Copyright (c) 2017 Free Electrons
+ *
+ * Authors:
+ *	Boris Brezillon <boris.brezillon@free-electrons.com>
+ *	Peter Pan <peterpandong@micron.com>
+ */
+
+#define pr_fmt(fmt)	"nand: " fmt
+
+#include <linux/module.h>
+#include <linux/mtd/nand.h>
+
+/**
+ * nanddev_isbad() - Check if a block is bad
+ * @nand: NAND device
+ * @pos: position pointing to the block we want to check
+ *
+ * Return: true if the block is bad, false otherwise.
+ */
+bool nanddev_isbad(struct nand_device *nand, const struct nand_pos *pos)
+{
+	if (nanddev_bbt_is_initialized(nand)) {
+		unsigned int entry;
+		int status;
+
+		entry = nanddev_bbt_pos_to_entry(nand, pos);
+		status = nanddev_bbt_get_block_status(nand, entry);
+		/* Lazy block status retrieval */
+		if (status == NAND_BBT_BLOCK_STATUS_UNKNOWN) {
+			if (nand->ops->isbad(nand, pos))
+				status = NAND_BBT_BLOCK_FACTORY_BAD;
+			else
+				status = NAND_BBT_BLOCK_GOOD;
+
+			nanddev_bbt_set_block_status(nand, entry, status);
+		}
+
+		if (status == NAND_BBT_BLOCK_WORN ||
+		    status == NAND_BBT_BLOCK_FACTORY_BAD)
+			return true;
+
+		return false;
+	}
+
+	return nand->ops->isbad(nand, pos);
+}
+EXPORT_SYMBOL_GPL(nanddev_isbad);
+
+/**
+ * nanddev_markbad() - Mark a block as bad
+ * @nand: NAND device
+ * @pos: position of the block to mark bad
+ *
+ * Mark a block bad. This function is updating the BBT if available and
+ * calls the low-level markbad hook (nand->ops->markbad()).
+ *
+ * Return: 0 in case of success, a negative error code otherwise.
+ */
+int nanddev_markbad(struct nand_device *nand, const struct nand_pos *pos)
+{
+	struct mtd_info *mtd = nanddev_to_mtd(nand);
+	unsigned int entry;
+	int ret = 0;
+
+	if (nanddev_isbad(nand, pos))
+		return 0;
+
+	ret = nand->ops->markbad(nand, pos);
+	if (ret)
+		pr_warn("failed to write BBM to block @%llx (err = %d)\n",
+			nanddev_pos_to_offs(nand, pos), ret);
+
+	if (!nanddev_bbt_is_initialized(nand))
+		goto out;
+
+	entry = nanddev_bbt_pos_to_entry(nand, pos);
+	ret = nanddev_bbt_set_block_status(nand, entry, NAND_BBT_BLOCK_WORN);
+	if (ret)
+		goto out;
+
+	ret = nanddev_bbt_update(nand);
+
+out:
+	if (!ret)
+		mtd->ecc_stats.badblocks++;
+
+	return ret;
+}
+EXPORT_SYMBOL_GPL(nanddev_markbad);
+
+/**
+ * nanddev_isreserved() - Check whether an eraseblock is reserved or not
+ * @nand: NAND device
+ * @pos: NAND position to test
+ *
+ * Checks whether the eraseblock pointed by @pos is reserved or not.
+ *
+ * Return: true if the eraseblock is reserved, false otherwise.
+ */
+bool nanddev_isreserved(struct nand_device *nand, const struct nand_pos *pos)
+{
+	unsigned int entry;
+	int status;
+
+	if (!nanddev_bbt_is_initialized(nand))
+		return false;
+
+	/* Return info from the table */
+	entry = nanddev_bbt_pos_to_entry(nand, pos);
+	status = nanddev_bbt_get_block_status(nand, entry);
+	return status == NAND_BBT_BLOCK_RESERVED;
+}
+EXPORT_SYMBOL_GPL(nanddev_isreserved);
+
+/**
+ * nanddev_erase() - Erase a NAND portion
+ * @nand: NAND device
+ * @pos: position of the block to erase
+ *
+ * Erases the block if it's not bad.
+ *
+ * Return: 0 in case of success, a negative error code otherwise.
+ */
+int nanddev_erase(struct nand_device *nand, const struct nand_pos *pos)
+{
+	if (nanddev_isbad(nand, pos) || nanddev_isreserved(nand, pos)) {
+		pr_warn("attempt to erase a bad/reserved block @%llx\n",
+			nanddev_pos_to_offs(nand, pos));
+		return -EIO;
+	}
+
+	return nand->ops->erase(nand, pos);
+}
+EXPORT_SYMBOL_GPL(nanddev_erase);
+
+/**
+ * nanddev_mtd_erase() - Generic mtd->_erase() implementation for NAND devices
+ * @mtd: MTD device
+ * @einfo: erase request
+ *
+ * This is a simple mtd->_erase() implementation iterating over all blocks
+ * concerned by @einfo and calling nand->ops->erase() on each of them.
+ *
+ * Note that mtd->_erase should not be directly assigned to this helper,
+ * because there's no locking here. NAND specialized layers should instead
+ * implement there own wrapper around nanddev_mtd_erase() taking the
+ * appropriate lock before calling nanddev_mtd_erase().
+ *
+ * Return: 0 in case of success, a negative error code otherwise.
+ */
+int nanddev_mtd_erase(struct mtd_info *mtd, struct erase_info *einfo)
+{
+	struct nand_device *nand = mtd_to_nanddev(mtd);
+	struct nand_pos pos, last;
+	int ret;
+
+	nanddev_offs_to_pos(nand, einfo->addr, &pos);
+	nanddev_offs_to_pos(nand, einfo->addr + einfo->len - 1, &last);
+	while (nanddev_pos_cmp(&pos, &last) <= 0) {
+		ret = nanddev_erase(nand, &pos);
+		if (ret) {
+			einfo->fail_addr = nanddev_pos_to_offs(nand, &pos);
+			einfo->state = MTD_ERASE_FAILED;
+
+			return ret;
+		}
+
+		nanddev_pos_next_eraseblock(nand, &pos);
+	}
+
+	einfo->state = MTD_ERASE_DONE;
+
+	return 0;
+}
+EXPORT_SYMBOL_GPL(nanddev_mtd_erase);
+
+/**
+ * nanddev_init() - Initialize a NAND device
+ * @nand: NAND device
+ * @ops: NAND device operations
+ * @owner: NAND device owner
+ *
+ * Initializes a NAND device object. Consistency checks are done on @ops and
+ * @nand->memorg. Also takes care of initializing the BBT.
+ *
+ * Return: 0 in case of success, a negative error code otherwise.
+ */
+int nanddev_init(struct nand_device *nand, const struct nand_ops *ops,
+		 struct module *owner)
+{
+	struct mtd_info *mtd = nanddev_to_mtd(nand);
+	struct nand_memory_organization *memorg = nanddev_get_memorg(nand);
+
+	if (!nand || !ops)
+		return -EINVAL;
+
+	if (!ops->erase || !ops->markbad || !ops->isbad)
+		return -EINVAL;
+
+	if (!memorg->bits_per_cell || !memorg->pagesize ||
+	    !memorg->pages_per_eraseblock || !memorg->eraseblocks_per_lun ||
+	    !memorg->planes_per_lun || !memorg->luns_per_target ||
+	    !memorg->ntargets)
+		return -EINVAL;
+
+	nand->rowconv.eraseblock_addr_shift =
+					fls(memorg->pages_per_eraseblock - 1);
+	nand->rowconv.lun_addr_shift = fls(memorg->eraseblocks_per_lun - 1) +
+				       nand->rowconv.eraseblock_addr_shift;
+
+	nand->ops = ops;
+
+	mtd->type = memorg->bits_per_cell == 1 ?
+		    MTD_NANDFLASH : MTD_MLCNANDFLASH;
+	mtd->flags = MTD_CAP_NANDFLASH;
+	mtd->erasesize = memorg->pagesize * memorg->pages_per_eraseblock;
+	mtd->writesize = memorg->pagesize;
+	mtd->writebufsize = memorg->pagesize;
+	mtd->oobsize = memorg->oobsize;
+	mtd->size = nanddev_size(nand);
+	mtd->owner = owner;
+
+	return nanddev_bbt_init(nand);
+}
+EXPORT_SYMBOL_GPL(nanddev_init);
+
+/**
+ * nanddev_cleanup() - Release resources allocated in nanddev_init()
+ * @nand: NAND device
+ *
+ * Basically undoes what has been done in nanddev_init().
+ */
+void nanddev_cleanup(struct nand_device *nand)
+{
+	if (nanddev_bbt_is_initialized(nand))
+		nanddev_bbt_cleanup(nand);
+}
+EXPORT_SYMBOL_GPL(nanddev_cleanup);
+
+MODULE_DESCRIPTION("Generic NAND framework");
+MODULE_AUTHOR("Boris Brezillon <boris.brezillon@free-electrons.com>");
+MODULE_LICENSE("GPL v2");
diff --git a/drivers/mtd/nand/onenand/Kconfig b/drivers/mtd/nand/onenand/Kconfig
new file mode 100644
index 000000000000..9dc15748947b
--- /dev/null
+++ b/drivers/mtd/nand/onenand/Kconfig
@@ -0,0 +1,71 @@
+menuconfig MTD_ONENAND
+	tristate "OneNAND Device Support"
+	depends on MTD
+	depends on HAS_IOMEM
+	help
+	  This enables support for accessing all type of OneNAND flash
+	  devices.
+
+if MTD_ONENAND
+
+config MTD_ONENAND_VERIFY_WRITE
+	bool "Verify OneNAND page writes"
+	help
+	  This adds an extra check when data is written to the flash. The
+	  OneNAND flash device internally checks only bits transitioning
+	  from 1 to 0. There is a rare possibility that even though the
+	  device thinks the write was successful, a bit could have been
+	  flipped accidentally due to device wear or something else.
+
+config MTD_ONENAND_GENERIC
+	tristate "OneNAND Flash device via platform device driver"
+	help
+	  Support for OneNAND flash via platform device driver.
+
+config MTD_ONENAND_OMAP2
+	tristate "OneNAND on OMAP2/OMAP3 support"
+	depends on ARCH_OMAP2 || ARCH_OMAP3
+	depends on OF || COMPILE_TEST
+	help
+	  Support for a OneNAND flash device connected to an OMAP2/OMAP3 SoC
+	  via the GPMC memory controller.
+	  Enable dmaengine and gpiolib for better performance.
+
+config MTD_ONENAND_SAMSUNG
+        tristate "OneNAND on Samsung SOC controller support"
+        depends on ARCH_S3C64XX || ARCH_S5PV210 || ARCH_EXYNOS4
+        help
+          Support for a OneNAND flash device connected to an Samsung SOC.
+          S3C64XX uses command mapping method.
+          S5PC110/S5PC210 use generic OneNAND method.
+
+config MTD_ONENAND_OTP
+	bool "OneNAND OTP Support"
+	help
+	  One Block of the NAND Flash Array memory is reserved as
+	  a One-Time Programmable Block memory area.
+	  Also, 1st Block of NAND Flash Array can be used as OTP.
+
+	  The OTP block can be read, programmed and locked using the same
+	  operations as any other NAND Flash Array memory block.
+	  OTP block cannot be erased.
+
+	  OTP block is fully-guaranteed to be a valid block.
+
+config MTD_ONENAND_2X_PROGRAM
+	bool "OneNAND 2X program support"
+	help
+	  The 2X Program is an extension of Program Operation.
+	  Since the device is equipped with two DataRAMs, and two-plane NAND
+	  Flash memory array, these two component enables simultaneous program
+	  of 4KiB. Plane1 has only even blocks such as block0, block2, block4
+	  while Plane2 has only odd blocks such as block1, block3, block5.
+	  So MTD regards it as 4KiB page size and 256KiB block size
+
+	  Now the following chips support it. (KFXXX16Q2M)
+	    Demux: KFG2G16Q2M, KFH4G16Q2M, KFW8G16Q2M,
+	    Mux:   KFM2G16Q2M, KFN4G16Q2M,
+
+	  And more recent chips
+
+endif # MTD_ONENAND
diff --git a/drivers/mtd/nand/onenand/Makefile b/drivers/mtd/nand/onenand/Makefile
new file mode 100644
index 000000000000..f8b624aca9cc
--- /dev/null
+++ b/drivers/mtd/nand/onenand/Makefile
@@ -0,0 +1,14 @@
+# SPDX-License-Identifier: GPL-2.0
+#
+# Makefile for the OneNAND MTD
+#
+
+# Core functionality.
+obj-$(CONFIG_MTD_ONENAND)		+= onenand.o
+
+# Board specific.
+obj-$(CONFIG_MTD_ONENAND_GENERIC)	+= generic.o
+obj-$(CONFIG_MTD_ONENAND_OMAP2)		+= omap2.o
+obj-$(CONFIG_MTD_ONENAND_SAMSUNG)       += samsung.o
+
+onenand-objs = onenand_base.o onenand_bbt.o
diff --git a/drivers/mtd/nand/onenand/generic.c b/drivers/mtd/nand/onenand/generic.c
new file mode 100644
index 000000000000..d5ccaf943b91
--- /dev/null
+++ b/drivers/mtd/nand/onenand/generic.c
@@ -0,0 +1,116 @@
+/*
+ *  Copyright (c) 2005 Samsung Electronics
+ *  Kyungmin Park <kyungmin.park@samsung.com>
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License version 2 as
+ * published by the Free Software Foundation.
+ *
+ *  Overview:
+ *   This is a device driver for the OneNAND flash for generic boards.
+ */
+
+#include <linux/module.h>
+#include <linux/slab.h>
+#include <linux/platform_device.h>
+#include <linux/mtd/mtd.h>
+#include <linux/mtd/onenand.h>
+#include <linux/mtd/partitions.h>
+#include <linux/io.h>
+
+/*
+ * Note: Driver name and platform data format have been updated!
+ *
+ * This version of the driver is named "onenand-flash" and takes struct
+ * onenand_platform_data as platform data. The old ARM-specific version
+ * with the name "onenand" used to take struct flash_platform_data.
+ */
+#define DRIVER_NAME	"onenand-flash"
+
+struct onenand_info {
+	struct mtd_info		mtd;
+	struct onenand_chip	onenand;
+};
+
+static int generic_onenand_probe(struct platform_device *pdev)
+{
+	struct onenand_info *info;
+	struct onenand_platform_data *pdata = dev_get_platdata(&pdev->dev);
+	struct resource *res = pdev->resource;
+	unsigned long size = resource_size(res);
+	int err;
+
+	info = kzalloc(sizeof(struct onenand_info), GFP_KERNEL);
+	if (!info)
+		return -ENOMEM;
+
+	if (!request_mem_region(res->start, size, dev_name(&pdev->dev))) {
+		err = -EBUSY;
+		goto out_free_info;
+	}
+
+	info->onenand.base = ioremap(res->start, size);
+	if (!info->onenand.base) {
+		err = -ENOMEM;
+		goto out_release_mem_region;
+	}
+
+	info->onenand.mmcontrol = pdata ? pdata->mmcontrol : NULL;
+	info->onenand.irq = platform_get_irq(pdev, 0);
+
+	info->mtd.dev.parent = &pdev->dev;
+	info->mtd.priv = &info->onenand;
+
+	if (onenand_scan(&info->mtd, 1)) {
+		err = -ENXIO;
+		goto out_iounmap;
+	}
+
+	err = mtd_device_parse_register(&info->mtd, NULL, NULL,
+					pdata ? pdata->parts : NULL,
+					pdata ? pdata->nr_parts : 0);
+
+	platform_set_drvdata(pdev, info);
+
+	return 0;
+
+out_iounmap:
+	iounmap(info->onenand.base);
+out_release_mem_region:
+	release_mem_region(res->start, size);
+out_free_info:
+	kfree(info);
+
+	return err;
+}
+
+static int generic_onenand_remove(struct platform_device *pdev)
+{
+	struct onenand_info *info = platform_get_drvdata(pdev);
+	struct resource *res = pdev->resource;
+	unsigned long size = resource_size(res);
+
+	if (info) {
+		onenand_release(&info->mtd);
+		release_mem_region(res->start, size);
+		iounmap(info->onenand.base);
+		kfree(info);
+	}
+
+	return 0;
+}
+
+static struct platform_driver generic_onenand_driver = {
+	.driver = {
+		.name		= DRIVER_NAME,
+	},
+	.probe		= generic_onenand_probe,
+	.remove		= generic_onenand_remove,
+};
+
+module_platform_driver(generic_onenand_driver);
+
+MODULE_LICENSE("GPL");
+MODULE_AUTHOR("Kyungmin Park <kyungmin.park@samsung.com>");
+MODULE_DESCRIPTION("Glue layer for OneNAND flash on generic boards");
+MODULE_ALIAS("platform:" DRIVER_NAME);
diff --git a/drivers/mtd/nand/onenand/omap2.c b/drivers/mtd/nand/onenand/omap2.c
new file mode 100644
index 000000000000..9c159f0dd9a6
--- /dev/null
+++ b/drivers/mtd/nand/onenand/omap2.c
@@ -0,0 +1,660 @@
+/*
+ *  OneNAND driver for OMAP2 / OMAP3
+ *
+ *  Copyright © 2005-2006 Nokia Corporation
+ *
+ *  Author: Jarkko Lavinen <jarkko.lavinen@nokia.com> and Juha Yrjölä
+ *  IRQ and DMA support written by Timo Teras
+ *
+ * This program is free software; you can redistribute it and/or modify it
+ * under the terms of the GNU General Public License version 2 as published by
+ * the Free Software Foundation.
+ *
+ * This program is distributed in the hope that it will be useful, but WITHOUT
+ * ANY WARRANTY; without even the implied warranty of MERCHANTABILITY or
+ * FITNESS FOR A PARTICULAR PURPOSE. See the GNU General Public License for
+ * more details.
+ *
+ * You should have received a copy of the GNU General Public License along with
+ * this program; see the file COPYING. If not, write to the Free Software
+ * Foundation, 59 Temple Place - Suite 330, Boston, MA 02111-1307, USA.
+ *
+ */
+
+#include <linux/device.h>
+#include <linux/module.h>
+#include <linux/mtd/mtd.h>
+#include <linux/mtd/onenand.h>
+#include <linux/mtd/partitions.h>
+#include <linux/of_device.h>
+#include <linux/omap-gpmc.h>
+#include <linux/platform_device.h>
+#include <linux/interrupt.h>
+#include <linux/delay.h>
+#include <linux/dma-mapping.h>
+#include <linux/dmaengine.h>
+#include <linux/io.h>
+#include <linux/slab.h>
+#include <linux/gpio/consumer.h>
+
+#include <asm/mach/flash.h>
+
+#define DRIVER_NAME "omap2-onenand"
+
+#define ONENAND_BUFRAM_SIZE	(1024 * 5)
+
+struct omap2_onenand {
+	struct platform_device *pdev;
+	int gpmc_cs;
+	unsigned long phys_base;
+	struct gpio_desc *int_gpiod;
+	struct mtd_info mtd;
+	struct onenand_chip onenand;
+	struct completion irq_done;
+	struct completion dma_done;
+	struct dma_chan *dma_chan;
+};
+
+static void omap2_onenand_dma_complete_func(void *completion)
+{
+	complete(completion);
+}
+
+static irqreturn_t omap2_onenand_interrupt(int irq, void *dev_id)
+{
+	struct omap2_onenand *c = dev_id;
+
+	complete(&c->irq_done);
+
+	return IRQ_HANDLED;
+}
+
+static inline unsigned short read_reg(struct omap2_onenand *c, int reg)
+{
+	return readw(c->onenand.base + reg);
+}
+
+static inline void write_reg(struct omap2_onenand *c, unsigned short value,
+			     int reg)
+{
+	writew(value, c->onenand.base + reg);
+}
+
+static int omap2_onenand_set_cfg(struct omap2_onenand *c,
+				 bool sr, bool sw,
+				 int latency, int burst_len)
+{
+	unsigned short reg = ONENAND_SYS_CFG1_RDY | ONENAND_SYS_CFG1_INT;
+
+	reg |= latency << ONENAND_SYS_CFG1_BRL_SHIFT;
+
+	switch (burst_len) {
+	case 0:		/* continuous */
+		break;
+	case 4:
+		reg |= ONENAND_SYS_CFG1_BL_4;
+		break;
+	case 8:
+		reg |= ONENAND_SYS_CFG1_BL_8;
+		break;
+	case 16:
+		reg |= ONENAND_SYS_CFG1_BL_16;
+		break;
+	case 32:
+		reg |= ONENAND_SYS_CFG1_BL_32;
+		break;
+	default:
+		return -EINVAL;
+	}
+
+	if (latency > 5)
+		reg |= ONENAND_SYS_CFG1_HF;
+	if (latency > 7)
+		reg |= ONENAND_SYS_CFG1_VHF;
+	if (sr)
+		reg |= ONENAND_SYS_CFG1_SYNC_READ;
+	if (sw)
+		reg |= ONENAND_SYS_CFG1_SYNC_WRITE;
+
+	write_reg(c, reg, ONENAND_REG_SYS_CFG1);
+
+	return 0;
+}
+
+static int omap2_onenand_get_freq(int ver)
+{
+	switch ((ver >> 4) & 0xf) {
+	case 0:
+		return 40;
+	case 1:
+		return 54;
+	case 2:
+		return 66;
+	case 3:
+		return 83;
+	case 4:
+		return 104;
+	}
+
+	return -EINVAL;
+}
+
+static void wait_err(char *msg, int state, unsigned int ctrl, unsigned int intr)
+{
+	printk(KERN_ERR "onenand_wait: %s! state %d ctrl 0x%04x intr 0x%04x\n",
+	       msg, state, ctrl, intr);
+}
+
+static void wait_warn(char *msg, int state, unsigned int ctrl,
+		      unsigned int intr)
+{
+	printk(KERN_WARNING "onenand_wait: %s! state %d ctrl 0x%04x "
+	       "intr 0x%04x\n", msg, state, ctrl, intr);
+}
+
+static int omap2_onenand_wait(struct mtd_info *mtd, int state)
+{
+	struct omap2_onenand *c = container_of(mtd, struct omap2_onenand, mtd);
+	struct onenand_chip *this = mtd->priv;
+	unsigned int intr = 0;
+	unsigned int ctrl, ctrl_mask;
+	unsigned long timeout;
+	u32 syscfg;
+
+	if (state == FL_RESETING || state == FL_PREPARING_ERASE ||
+	    state == FL_VERIFYING_ERASE) {
+		int i = 21;
+		unsigned int intr_flags = ONENAND_INT_MASTER;
+
+		switch (state) {
+		case FL_RESETING:
+			intr_flags |= ONENAND_INT_RESET;
+			break;
+		case FL_PREPARING_ERASE:
+			intr_flags |= ONENAND_INT_ERASE;
+			break;
+		case FL_VERIFYING_ERASE:
+			i = 101;
+			break;
+		}
+
+		while (--i) {
+			udelay(1);
+			intr = read_reg(c, ONENAND_REG_INTERRUPT);
+			if (intr & ONENAND_INT_MASTER)
+				break;
+		}
+		ctrl = read_reg(c, ONENAND_REG_CTRL_STATUS);
+		if (ctrl & ONENAND_CTRL_ERROR) {
+			wait_err("controller error", state, ctrl, intr);
+			return -EIO;
+		}
+		if ((intr & intr_flags) == intr_flags)
+			return 0;
+		/* Continue in wait for interrupt branch */
+	}
+
+	if (state != FL_READING) {
+		int result;
+
+		/* Turn interrupts on */
+		syscfg = read_reg(c, ONENAND_REG_SYS_CFG1);
+		if (!(syscfg & ONENAND_SYS_CFG1_IOBE)) {
+			syscfg |= ONENAND_SYS_CFG1_IOBE;
+			write_reg(c, syscfg, ONENAND_REG_SYS_CFG1);
+			/* Add a delay to let GPIO settle */
+			syscfg = read_reg(c, ONENAND_REG_SYS_CFG1);
+		}
+
+		reinit_completion(&c->irq_done);
+		result = gpiod_get_value(c->int_gpiod);
+		if (result < 0) {
+			ctrl = read_reg(c, ONENAND_REG_CTRL_STATUS);
+			intr = read_reg(c, ONENAND_REG_INTERRUPT);
+			wait_err("gpio error", state, ctrl, intr);
+			return result;
+		} else if (result == 0) {
+			int retry_cnt = 0;
+retry:
+			if (!wait_for_completion_io_timeout(&c->irq_done,
+						msecs_to_jiffies(20))) {
+				/* Timeout after 20ms */
+				ctrl = read_reg(c, ONENAND_REG_CTRL_STATUS);
+				if (ctrl & ONENAND_CTRL_ONGO &&
+				    !this->ongoing) {
+					/*
+					 * The operation seems to be still going
+					 * so give it some more time.
+					 */
+					retry_cnt += 1;
+					if (retry_cnt < 3)
+						goto retry;
+					intr = read_reg(c,
+							ONENAND_REG_INTERRUPT);
+					wait_err("timeout", state, ctrl, intr);
+					return -EIO;
+				}
+				intr = read_reg(c, ONENAND_REG_INTERRUPT);
+				if ((intr & ONENAND_INT_MASTER) == 0)
+					wait_warn("timeout", state, ctrl, intr);
+			}
+		}
+	} else {
+		int retry_cnt = 0;
+
+		/* Turn interrupts off */
+		syscfg = read_reg(c, ONENAND_REG_SYS_CFG1);
+		syscfg &= ~ONENAND_SYS_CFG1_IOBE;
+		write_reg(c, syscfg, ONENAND_REG_SYS_CFG1);
+
+		timeout = jiffies + msecs_to_jiffies(20);
+		while (1) {
+			if (time_before(jiffies, timeout)) {
+				intr = read_reg(c, ONENAND_REG_INTERRUPT);
+				if (intr & ONENAND_INT_MASTER)
+					break;
+			} else {
+				/* Timeout after 20ms */
+				ctrl = read_reg(c, ONENAND_REG_CTRL_STATUS);
+				if (ctrl & ONENAND_CTRL_ONGO) {
+					/*
+					 * The operation seems to be still going
+					 * so give it some more time.
+					 */
+					retry_cnt += 1;
+					if (retry_cnt < 3) {
+						timeout = jiffies +
+							  msecs_to_jiffies(20);
+						continue;
+					}
+				}
+				break;
+			}
+		}
+	}
+
+	intr = read_reg(c, ONENAND_REG_INTERRUPT);
+	ctrl = read_reg(c, ONENAND_REG_CTRL_STATUS);
+
+	if (intr & ONENAND_INT_READ) {
+		int ecc = read_reg(c, ONENAND_REG_ECC_STATUS);
+
+		if (ecc) {
+			unsigned int addr1, addr8;
+
+			addr1 = read_reg(c, ONENAND_REG_START_ADDRESS1);
+			addr8 = read_reg(c, ONENAND_REG_START_ADDRESS8);
+			if (ecc & ONENAND_ECC_2BIT_ALL) {
+				printk(KERN_ERR "onenand_wait: ECC error = "
+				       "0x%04x, addr1 %#x, addr8 %#x\n",
+				       ecc, addr1, addr8);
+				mtd->ecc_stats.failed++;
+				return -EBADMSG;
+			} else if (ecc & ONENAND_ECC_1BIT_ALL) {
+				printk(KERN_NOTICE "onenand_wait: correctable "
+				       "ECC error = 0x%04x, addr1 %#x, "
+				       "addr8 %#x\n", ecc, addr1, addr8);
+				mtd->ecc_stats.corrected++;
+			}
+		}
+	} else if (state == FL_READING) {
+		wait_err("timeout", state, ctrl, intr);
+		return -EIO;
+	}
+
+	if (ctrl & ONENAND_CTRL_ERROR) {
+		wait_err("controller error", state, ctrl, intr);
+		if (ctrl & ONENAND_CTRL_LOCK)
+			printk(KERN_ERR "onenand_wait: "
+					"Device is write protected!!!\n");
+		return -EIO;
+	}
+
+	ctrl_mask = 0xFE9F;
+	if (this->ongoing)
+		ctrl_mask &= ~0x8000;
+
+	if (ctrl & ctrl_mask)
+		wait_warn("unexpected controller status", state, ctrl, intr);
+
+	return 0;
+}
+
+static inline int omap2_onenand_bufferram_offset(struct mtd_info *mtd, int area)
+{
+	struct onenand_chip *this = mtd->priv;
+
+	if (ONENAND_CURRENT_BUFFERRAM(this)) {
+		if (area == ONENAND_DATARAM)
+			return this->writesize;
+		if (area == ONENAND_SPARERAM)
+			return mtd->oobsize;
+	}
+
+	return 0;
+}
+
+static inline int omap2_onenand_dma_transfer(struct omap2_onenand *c,
+					     dma_addr_t src, dma_addr_t dst,
+					     size_t count)
+{
+	struct dma_async_tx_descriptor *tx;
+	dma_cookie_t cookie;
+
+	tx = dmaengine_prep_dma_memcpy(c->dma_chan, dst, src, count, 0);
+	if (!tx) {
+		dev_err(&c->pdev->dev, "Failed to prepare DMA memcpy\n");
+		return -EIO;
+	}
+
+	reinit_completion(&c->dma_done);
+
+	tx->callback = omap2_onenand_dma_complete_func;
+	tx->callback_param = &c->dma_done;
+
+	cookie = tx->tx_submit(tx);
+	if (dma_submit_error(cookie)) {
+		dev_err(&c->pdev->dev, "Failed to do DMA tx_submit\n");
+		return -EIO;
+	}
+
+	dma_async_issue_pending(c->dma_chan);
+
+	if (!wait_for_completion_io_timeout(&c->dma_done,
+					    msecs_to_jiffies(20))) {
+		dmaengine_terminate_sync(c->dma_chan);
+		return -ETIMEDOUT;
+	}
+
+	return 0;
+}
+
+static int omap2_onenand_read_bufferram(struct mtd_info *mtd, int area,
+					unsigned char *buffer, int offset,
+					size_t count)
+{
+	struct omap2_onenand *c = container_of(mtd, struct omap2_onenand, mtd);
+	struct onenand_chip *this = mtd->priv;
+	dma_addr_t dma_src, dma_dst;
+	int bram_offset;
+	void *buf = (void *)buffer;
+	size_t xtra;
+	int ret;
+
+	bram_offset = omap2_onenand_bufferram_offset(mtd, area) + area + offset;
+	if (bram_offset & 3 || (size_t)buf & 3 || count < 384)
+		goto out_copy;
+
+	/* panic_write() may be in an interrupt context */
+	if (in_interrupt() || oops_in_progress)
+		goto out_copy;
+
+	if (buf >= high_memory) {
+		struct page *p1;
+
+		if (((size_t)buf & PAGE_MASK) !=
+		    ((size_t)(buf + count - 1) & PAGE_MASK))
+			goto out_copy;
+		p1 = vmalloc_to_page(buf);
+		if (!p1)
+			goto out_copy;
+		buf = page_address(p1) + ((size_t)buf & ~PAGE_MASK);
+	}
+
+	xtra = count & 3;
+	if (xtra) {
+		count -= xtra;
+		memcpy(buf + count, this->base + bram_offset + count, xtra);
+	}
+
+	dma_src = c->phys_base + bram_offset;
+	dma_dst = dma_map_single(&c->pdev->dev, buf, count, DMA_FROM_DEVICE);
+	if (dma_mapping_error(&c->pdev->dev, dma_dst)) {
+		dev_err(&c->pdev->dev,
+			"Couldn't DMA map a %d byte buffer\n",
+			count);
+		goto out_copy;
+	}
+
+	ret = omap2_onenand_dma_transfer(c, dma_src, dma_dst, count);
+	dma_unmap_single(&c->pdev->dev, dma_dst, count, DMA_FROM_DEVICE);
+
+	if (ret) {
+		dev_err(&c->pdev->dev, "timeout waiting for DMA\n");
+		goto out_copy;
+	}
+
+	return 0;
+
+out_copy:
+	memcpy(buf, this->base + bram_offset, count);
+	return 0;
+}
+
+static int omap2_onenand_write_bufferram(struct mtd_info *mtd, int area,
+					 const unsigned char *buffer,
+					 int offset, size_t count)
+{
+	struct omap2_onenand *c = container_of(mtd, struct omap2_onenand, mtd);
+	struct onenand_chip *this = mtd->priv;
+	dma_addr_t dma_src, dma_dst;
+	int bram_offset;
+	void *buf = (void *)buffer;
+	int ret;
+
+	bram_offset = omap2_onenand_bufferram_offset(mtd, area) + area + offset;
+	if (bram_offset & 3 || (size_t)buf & 3 || count < 384)
+		goto out_copy;
+
+	/* panic_write() may be in an interrupt context */
+	if (in_interrupt() || oops_in_progress)
+		goto out_copy;
+
+	if (buf >= high_memory) {
+		struct page *p1;
+
+		if (((size_t)buf & PAGE_MASK) !=
+		    ((size_t)(buf + count - 1) & PAGE_MASK))
+			goto out_copy;
+		p1 = vmalloc_to_page(buf);
+		if (!p1)
+			goto out_copy;
+		buf = page_address(p1) + ((size_t)buf & ~PAGE_MASK);
+	}
+
+	dma_src = dma_map_single(&c->pdev->dev, buf, count, DMA_TO_DEVICE);
+	dma_dst = c->phys_base + bram_offset;
+	if (dma_mapping_error(&c->pdev->dev, dma_src)) {
+		dev_err(&c->pdev->dev,
+			"Couldn't DMA map a %d byte buffer\n",
+			count);
+		return -1;
+	}
+
+	ret = omap2_onenand_dma_transfer(c, dma_src, dma_dst, count);
+	dma_unmap_single(&c->pdev->dev, dma_src, count, DMA_TO_DEVICE);
+
+	if (ret) {
+		dev_err(&c->pdev->dev, "timeout waiting for DMA\n");
+		goto out_copy;
+	}
+
+	return 0;
+
+out_copy:
+	memcpy(this->base + bram_offset, buf, count);
+	return 0;
+}
+
+static void omap2_onenand_shutdown(struct platform_device *pdev)
+{
+	struct omap2_onenand *c = dev_get_drvdata(&pdev->dev);
+
+	/* With certain content in the buffer RAM, the OMAP boot ROM code
+	 * can recognize the flash chip incorrectly. Zero it out before
+	 * soft reset.
+	 */
+	memset((__force void *)c->onenand.base, 0, ONENAND_BUFRAM_SIZE);
+}
+
+static int omap2_onenand_probe(struct platform_device *pdev)
+{
+	u32 val;
+	dma_cap_mask_t mask;
+	int freq, latency, r;
+	struct resource *res;
+	struct omap2_onenand *c;
+	struct gpmc_onenand_info info;
+	struct device *dev = &pdev->dev;
+	struct device_node *np = dev->of_node;
+
+	res = platform_get_resource(pdev, IORESOURCE_MEM, 0);
+	if (!res) {
+		dev_err(dev, "error getting memory resource\n");
+		return -EINVAL;
+	}
+
+	r = of_property_read_u32(np, "reg", &val);
+	if (r) {
+		dev_err(dev, "reg not found in DT\n");
+		return r;
+	}
+
+	c = devm_kzalloc(dev, sizeof(struct omap2_onenand), GFP_KERNEL);
+	if (!c)
+		return -ENOMEM;
+
+	init_completion(&c->irq_done);
+	init_completion(&c->dma_done);
+	c->gpmc_cs = val;
+	c->phys_base = res->start;
+
+	c->onenand.base = devm_ioremap_resource(dev, res);
+	if (IS_ERR(c->onenand.base))
+		return PTR_ERR(c->onenand.base);
+
+	c->int_gpiod = devm_gpiod_get_optional(dev, "int", GPIOD_IN);
+	if (IS_ERR(c->int_gpiod)) {
+		r = PTR_ERR(c->int_gpiod);
+		/* Just try again if this happens */
+		if (r != -EPROBE_DEFER)
+			dev_err(dev, "error getting gpio: %d\n", r);
+		return r;
+	}
+
+	if (c->int_gpiod) {
+		r = devm_request_irq(dev, gpiod_to_irq(c->int_gpiod),
+				     omap2_onenand_interrupt,
+				     IRQF_TRIGGER_RISING, "onenand", c);
+		if (r)
+			return r;
+
+		c->onenand.wait = omap2_onenand_wait;
+	}
+
+	dma_cap_zero(mask);
+	dma_cap_set(DMA_MEMCPY, mask);
+
+	c->dma_chan = dma_request_channel(mask, NULL, NULL);
+	if (c->dma_chan) {
+		c->onenand.read_bufferram = omap2_onenand_read_bufferram;
+		c->onenand.write_bufferram = omap2_onenand_write_bufferram;
+	}
+
+	c->pdev = pdev;
+	c->mtd.priv = &c->onenand;
+	c->mtd.dev.parent = dev;
+	mtd_set_of_node(&c->mtd, dev->of_node);
+
+	dev_info(dev, "initializing on CS%d (0x%08lx), va %p, %s mode\n",
+		 c->gpmc_cs, c->phys_base, c->onenand.base,
+		 c->dma_chan ? "DMA" : "PIO");
+
+	if ((r = onenand_scan(&c->mtd, 1)) < 0)
+		goto err_release_dma;
+
+	freq = omap2_onenand_get_freq(c->onenand.version_id);
+	if (freq > 0) {
+		switch (freq) {
+		case 104:
+			latency = 7;
+			break;
+		case 83:
+			latency = 6;
+			break;
+		case 66:
+			latency = 5;
+			break;
+		case 56:
+			latency = 4;
+			break;
+		default:	/* 40 MHz or lower */
+			latency = 3;
+			break;
+		}
+
+		r = gpmc_omap_onenand_set_timings(dev, c->gpmc_cs,
+						  freq, latency, &info);
+		if (r)
+			goto err_release_onenand;
+
+		r = omap2_onenand_set_cfg(c, info.sync_read, info.sync_write,
+					  latency, info.burst_len);
+		if (r)
+			goto err_release_onenand;
+
+		if (info.sync_read || info.sync_write)
+			dev_info(dev, "optimized timings for %d MHz\n", freq);
+	}
+
+	r = mtd_device_register(&c->mtd, NULL, 0);
+	if (r)
+		goto err_release_onenand;
+
+	platform_set_drvdata(pdev, c);
+
+	return 0;
+
+err_release_onenand:
+	onenand_release(&c->mtd);
+err_release_dma:
+	if (c->dma_chan)
+		dma_release_channel(c->dma_chan);
+
+	return r;
+}
+
+static int omap2_onenand_remove(struct platform_device *pdev)
+{
+	struct omap2_onenand *c = dev_get_drvdata(&pdev->dev);
+
+	onenand_release(&c->mtd);
+	if (c->dma_chan)
+		dma_release_channel(c->dma_chan);
+	omap2_onenand_shutdown(pdev);
+
+	return 0;
+}
+
+static const struct of_device_id omap2_onenand_id_table[] = {
+	{ .compatible = "ti,omap2-onenand", },
+	{},
+};
+MODULE_DEVICE_TABLE(of, omap2_onenand_id_table);
+
+static struct platform_driver omap2_onenand_driver = {
+	.probe		= omap2_onenand_probe,
+	.remove		= omap2_onenand_remove,
+	.shutdown	= omap2_onenand_shutdown,
+	.driver		= {
+		.name	= DRIVER_NAME,
+		.of_match_table = omap2_onenand_id_table,
+	},
+};
+
+module_platform_driver(omap2_onenand_driver);
+
+MODULE_ALIAS("platform:" DRIVER_NAME);
+MODULE_LICENSE("GPL");
+MODULE_AUTHOR("Jarkko Lavinen <jarkko.lavinen@nokia.com>");
+MODULE_DESCRIPTION("Glue layer for OneNAND flash on OMAP2 / OMAP3");
diff --git a/drivers/mtd/nand/onenand/onenand_base.c b/drivers/mtd/nand/onenand/onenand_base.c
new file mode 100644
index 000000000000..b7105192cb12
--- /dev/null
+++ b/drivers/mtd/nand/onenand/onenand_base.c
@@ -0,0 +1,4014 @@
+/*
+ *  Copyright © 2005-2009 Samsung Electronics
+ *  Copyright © 2007 Nokia Corporation
+ *
+ *  Kyungmin Park <kyungmin.park@samsung.com>
+ *
+ *  Credits:
+ *	Adrian Hunter <ext-adrian.hunter@nokia.com>:
+ *	auto-placement support, read-while load support, various fixes
+ *
+ *	Vishak G <vishak.g at samsung.com>, Rohit Hagargundgi <h.rohit at samsung.com>
+ *	Flex-OneNAND support
+ *	Amul Kumar Saha <amul.saha at samsung.com>
+ *	OTP support
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License version 2 as
+ * published by the Free Software Foundation.
+ */
+
+#include <linux/kernel.h>
+#include <linux/module.h>
+#include <linux/moduleparam.h>
+#include <linux/slab.h>
+#include <linux/sched.h>
+#include <linux/delay.h>
+#include <linux/interrupt.h>
+#include <linux/jiffies.h>
+#include <linux/mtd/mtd.h>
+#include <linux/mtd/onenand.h>
+#include <linux/mtd/partitions.h>
+
+#include <asm/io.h>
+
+/*
+ * Multiblock erase if number of blocks to erase is 2 or more.
+ * Maximum number of blocks for simultaneous erase is 64.
+ */
+#define MB_ERASE_MIN_BLK_COUNT 2
+#define MB_ERASE_MAX_BLK_COUNT 64
+
+/* Default Flex-OneNAND boundary and lock respectively */
+static int flex_bdry[MAX_DIES * 2] = { -1, 0, -1, 0 };
+
+module_param_array(flex_bdry, int, NULL, 0400);
+MODULE_PARM_DESC(flex_bdry,	"SLC Boundary information for Flex-OneNAND"
+				"Syntax:flex_bdry=DIE_BDRY,LOCK,..."
+				"DIE_BDRY: SLC boundary of the die"
+				"LOCK: Locking information for SLC boundary"
+				"    : 0->Set boundary in unlocked status"
+				"    : 1->Set boundary in locked status");
+
+/* Default OneNAND/Flex-OneNAND OTP options*/
+static int otp;
+
+module_param(otp, int, 0400);
+MODULE_PARM_DESC(otp,	"Corresponding behaviour of OneNAND in OTP"
+			"Syntax : otp=LOCK_TYPE"
+			"LOCK_TYPE : Keys issued, for specific OTP Lock type"
+			"	   : 0 -> Default (No Blocks Locked)"
+			"	   : 1 -> OTP Block lock"
+			"	   : 2 -> 1st Block lock"
+			"	   : 3 -> BOTH OTP Block and 1st Block lock");
+
+/*
+ * flexonenand_oob_128 - oob info for Flex-Onenand with 4KB page
+ * For now, we expose only 64 out of 80 ecc bytes
+ */
+static int flexonenand_ooblayout_ecc(struct mtd_info *mtd, int section,
+				     struct mtd_oob_region *oobregion)
+{
+	if (section > 7)
+		return -ERANGE;
+
+	oobregion->offset = (section * 16) + 6;
+	oobregion->length = 10;
+
+	return 0;
+}
+
+static int flexonenand_ooblayout_free(struct mtd_info *mtd, int section,
+				      struct mtd_oob_region *oobregion)
+{
+	if (section > 7)
+		return -ERANGE;
+
+	oobregion->offset = (section * 16) + 2;
+	oobregion->length = 4;
+
+	return 0;
+}
+
+static const struct mtd_ooblayout_ops flexonenand_ooblayout_ops = {
+	.ecc = flexonenand_ooblayout_ecc,
+	.free = flexonenand_ooblayout_free,
+};
+
+/*
+ * onenand_oob_128 - oob info for OneNAND with 4KB page
+ *
+ * Based on specification:
+ * 4Gb M-die OneNAND Flash (KFM4G16Q4M, KFN8G16Q4M). Rev. 1.3, Apr. 2010
+ *
+ */
+static int onenand_ooblayout_128_ecc(struct mtd_info *mtd, int section,
+				     struct mtd_oob_region *oobregion)
+{
+	if (section > 7)
+		return -ERANGE;
+
+	oobregion->offset = (section * 16) + 7;
+	oobregion->length = 9;
+
+	return 0;
+}
+
+static int onenand_ooblayout_128_free(struct mtd_info *mtd, int section,
+				      struct mtd_oob_region *oobregion)
+{
+	if (section >= 8)
+		return -ERANGE;
+
+	/*
+	 * free bytes are using the spare area fields marked as
+	 * "Managed by internal ECC logic for Logical Sector Number area"
+	 */
+	oobregion->offset = (section * 16) + 2;
+	oobregion->length = 3;
+
+	return 0;
+}
+
+static const struct mtd_ooblayout_ops onenand_oob_128_ooblayout_ops = {
+	.ecc = onenand_ooblayout_128_ecc,
+	.free = onenand_ooblayout_128_free,
+};
+
+/**
+ * onenand_oob_32_64 - oob info for large (2KB) page
+ */
+static int onenand_ooblayout_32_64_ecc(struct mtd_info *mtd, int section,
+				       struct mtd_oob_region *oobregion)
+{
+	if (section > 3)
+		return -ERANGE;
+
+	oobregion->offset = (section * 16) + 8;
+	oobregion->length = 5;
+
+	return 0;
+}
+
+static int onenand_ooblayout_32_64_free(struct mtd_info *mtd, int section,
+					struct mtd_oob_region *oobregion)
+{
+	int sections = (mtd->oobsize / 32) * 2;
+
+	if (section >= sections)
+		return -ERANGE;
+
+	if (section & 1) {
+		oobregion->offset = ((section - 1) * 16) + 14;
+		oobregion->length = 2;
+	} else  {
+		oobregion->offset = (section * 16) + 2;
+		oobregion->length = 3;
+	}
+
+	return 0;
+}
+
+static const struct mtd_ooblayout_ops onenand_oob_32_64_ooblayout_ops = {
+	.ecc = onenand_ooblayout_32_64_ecc,
+	.free = onenand_ooblayout_32_64_free,
+};
+
+static const unsigned char ffchars[] = {
+	0xff, 0xff, 0xff, 0xff, 0xff, 0xff, 0xff, 0xff,
+	0xff, 0xff, 0xff, 0xff, 0xff, 0xff, 0xff, 0xff,	/* 16 */
+	0xff, 0xff, 0xff, 0xff, 0xff, 0xff, 0xff, 0xff,
+	0xff, 0xff, 0xff, 0xff, 0xff, 0xff, 0xff, 0xff,	/* 32 */
+	0xff, 0xff, 0xff, 0xff, 0xff, 0xff, 0xff, 0xff,
+	0xff, 0xff, 0xff, 0xff, 0xff, 0xff, 0xff, 0xff,	/* 48 */
+	0xff, 0xff, 0xff, 0xff, 0xff, 0xff, 0xff, 0xff,
+	0xff, 0xff, 0xff, 0xff, 0xff, 0xff, 0xff, 0xff,	/* 64 */
+	0xff, 0xff, 0xff, 0xff, 0xff, 0xff, 0xff, 0xff,
+	0xff, 0xff, 0xff, 0xff, 0xff, 0xff, 0xff, 0xff,	/* 80 */
+	0xff, 0xff, 0xff, 0xff, 0xff, 0xff, 0xff, 0xff,
+	0xff, 0xff, 0xff, 0xff, 0xff, 0xff, 0xff, 0xff,	/* 96 */
+	0xff, 0xff, 0xff, 0xff, 0xff, 0xff, 0xff, 0xff,
+	0xff, 0xff, 0xff, 0xff, 0xff, 0xff, 0xff, 0xff,	/* 112 */
+	0xff, 0xff, 0xff, 0xff, 0xff, 0xff, 0xff, 0xff,
+	0xff, 0xff, 0xff, 0xff, 0xff, 0xff, 0xff, 0xff,	/* 128 */
+};
+
+/**
+ * onenand_readw - [OneNAND Interface] Read OneNAND register
+ * @param addr		address to read
+ *
+ * Read OneNAND register
+ */
+static unsigned short onenand_readw(void __iomem *addr)
+{
+	return readw(addr);
+}
+
+/**
+ * onenand_writew - [OneNAND Interface] Write OneNAND register with value
+ * @param value		value to write
+ * @param addr		address to write
+ *
+ * Write OneNAND register with value
+ */
+static void onenand_writew(unsigned short value, void __iomem *addr)
+{
+	writew(value, addr);
+}
+
+/**
+ * onenand_block_address - [DEFAULT] Get block address
+ * @param this		onenand chip data structure
+ * @param block		the block
+ * @return		translated block address if DDP, otherwise same
+ *
+ * Setup Start Address 1 Register (F100h)
+ */
+static int onenand_block_address(struct onenand_chip *this, int block)
+{
+	/* Device Flash Core select, NAND Flash Block Address */
+	if (block & this->density_mask)
+		return ONENAND_DDP_CHIP1 | (block ^ this->density_mask);
+
+	return block;
+}
+
+/**
+ * onenand_bufferram_address - [DEFAULT] Get bufferram address
+ * @param this		onenand chip data structure
+ * @param block		the block
+ * @return		set DBS value if DDP, otherwise 0
+ *
+ * Setup Start Address 2 Register (F101h) for DDP
+ */
+static int onenand_bufferram_address(struct onenand_chip *this, int block)
+{
+	/* Device BufferRAM Select */
+	if (block & this->density_mask)
+		return ONENAND_DDP_CHIP1;
+
+	return ONENAND_DDP_CHIP0;
+}
+
+/**
+ * onenand_page_address - [DEFAULT] Get page address
+ * @param page		the page address
+ * @param sector	the sector address
+ * @return		combined page and sector address
+ *
+ * Setup Start Address 8 Register (F107h)
+ */
+static int onenand_page_address(int page, int sector)
+{
+	/* Flash Page Address, Flash Sector Address */
+	int fpa, fsa;
+
+	fpa = page & ONENAND_FPA_MASK;
+	fsa = sector & ONENAND_FSA_MASK;
+
+	return ((fpa << ONENAND_FPA_SHIFT) | fsa);
+}
+
+/**
+ * onenand_buffer_address - [DEFAULT] Get buffer address
+ * @param dataram1	DataRAM index
+ * @param sectors	the sector address
+ * @param count		the number of sectors
+ * @return		the start buffer value
+ *
+ * Setup Start Buffer Register (F200h)
+ */
+static int onenand_buffer_address(int dataram1, int sectors, int count)
+{
+	int bsa, bsc;
+
+	/* BufferRAM Sector Address */
+	bsa = sectors & ONENAND_BSA_MASK;
+
+	if (dataram1)
+		bsa |= ONENAND_BSA_DATARAM1;	/* DataRAM1 */
+	else
+		bsa |= ONENAND_BSA_DATARAM0;	/* DataRAM0 */
+
+	/* BufferRAM Sector Count */
+	bsc = count & ONENAND_BSC_MASK;
+
+	return ((bsa << ONENAND_BSA_SHIFT) | bsc);
+}
+
+/**
+ * flexonenand_block- For given address return block number
+ * @param this         - OneNAND device structure
+ * @param addr		- Address for which block number is needed
+ */
+static unsigned flexonenand_block(struct onenand_chip *this, loff_t addr)
+{
+	unsigned boundary, blk, die = 0;
+
+	if (ONENAND_IS_DDP(this) && addr >= this->diesize[0]) {
+		die = 1;
+		addr -= this->diesize[0];
+	}
+
+	boundary = this->boundary[die];
+
+	blk = addr >> (this->erase_shift - 1);
+	if (blk > boundary)
+		blk = (blk + boundary + 1) >> 1;
+
+	blk += die ? this->density_mask : 0;
+	return blk;
+}
+
+inline unsigned onenand_block(struct onenand_chip *this, loff_t addr)
+{
+	if (!FLEXONENAND(this))
+		return addr >> this->erase_shift;
+	return flexonenand_block(this, addr);
+}
+
+/**
+ * flexonenand_addr - Return address of the block
+ * @this:		OneNAND device structure
+ * @block:		Block number on Flex-OneNAND
+ *
+ * Return address of the block
+ */
+static loff_t flexonenand_addr(struct onenand_chip *this, int block)
+{
+	loff_t ofs = 0;
+	int die = 0, boundary;
+
+	if (ONENAND_IS_DDP(this) && block >= this->density_mask) {
+		block -= this->density_mask;
+		die = 1;
+		ofs = this->diesize[0];
+	}
+
+	boundary = this->boundary[die];
+	ofs += (loff_t)block << (this->erase_shift - 1);
+	if (block > (boundary + 1))
+		ofs += (loff_t)(block - boundary - 1) << (this->erase_shift - 1);
+	return ofs;
+}
+
+loff_t onenand_addr(struct onenand_chip *this, int block)
+{
+	if (!FLEXONENAND(this))
+		return (loff_t)block << this->erase_shift;
+	return flexonenand_addr(this, block);
+}
+EXPORT_SYMBOL(onenand_addr);
+
+/**
+ * onenand_get_density - [DEFAULT] Get OneNAND density
+ * @param dev_id	OneNAND device ID
+ *
+ * Get OneNAND density from device ID
+ */
+static inline int onenand_get_density(int dev_id)
+{
+	int density = dev_id >> ONENAND_DEVICE_DENSITY_SHIFT;
+	return (density & ONENAND_DEVICE_DENSITY_MASK);
+}
+
+/**
+ * flexonenand_region - [Flex-OneNAND] Return erase region of addr
+ * @param mtd		MTD device structure
+ * @param addr		address whose erase region needs to be identified
+ */
+int flexonenand_region(struct mtd_info *mtd, loff_t addr)
+{
+	int i;
+
+	for (i = 0; i < mtd->numeraseregions; i++)
+		if (addr < mtd->eraseregions[i].offset)
+			break;
+	return i - 1;
+}
+EXPORT_SYMBOL(flexonenand_region);
+
+/**
+ * onenand_command - [DEFAULT] Send command to OneNAND device
+ * @param mtd		MTD device structure
+ * @param cmd		the command to be sent
+ * @param addr		offset to read from or write to
+ * @param len		number of bytes to read or write
+ *
+ * Send command to OneNAND device. This function is used for middle/large page
+ * devices (1KB/2KB Bytes per page)
+ */
+static int onenand_command(struct mtd_info *mtd, int cmd, loff_t addr, size_t len)
+{
+	struct onenand_chip *this = mtd->priv;
+	int value, block, page;
+
+	/* Address translation */
+	switch (cmd) {
+	case ONENAND_CMD_UNLOCK:
+	case ONENAND_CMD_LOCK:
+	case ONENAND_CMD_LOCK_TIGHT:
+	case ONENAND_CMD_UNLOCK_ALL:
+		block = -1;
+		page = -1;
+		break;
+
+	case FLEXONENAND_CMD_PI_ACCESS:
+		/* addr contains die index */
+		block = addr * this->density_mask;
+		page = -1;
+		break;
+
+	case ONENAND_CMD_ERASE:
+	case ONENAND_CMD_MULTIBLOCK_ERASE:
+	case ONENAND_CMD_ERASE_VERIFY:
+	case ONENAND_CMD_BUFFERRAM:
+	case ONENAND_CMD_OTP_ACCESS:
+		block = onenand_block(this, addr);
+		page = -1;
+		break;
+
+	case FLEXONENAND_CMD_READ_PI:
+		cmd = ONENAND_CMD_READ;
+		block = addr * this->density_mask;
+		page = 0;
+		break;
+
+	default:
+		block = onenand_block(this, addr);
+		if (FLEXONENAND(this))
+			page = (int) (addr - onenand_addr(this, block))>>\
+				this->page_shift;
+		else
+			page = (int) (addr >> this->page_shift);
+		if (ONENAND_IS_2PLANE(this)) {
+			/* Make the even block number */
+			block &= ~1;
+			/* Is it the odd plane? */
+			if (addr & this->writesize)
+				block++;
+			page >>= 1;
+		}
+		page &= this->page_mask;
+		break;
+	}
+
+	/* NOTE: The setting order of the registers is very important! */
+	if (cmd == ONENAND_CMD_BUFFERRAM) {
+		/* Select DataRAM for DDP */
+		value = onenand_bufferram_address(this, block);
+		this->write_word(value, this->base + ONENAND_REG_START_ADDRESS2);
+
+		if (ONENAND_IS_2PLANE(this) || ONENAND_IS_4KB_PAGE(this))
+			/* It is always BufferRAM0 */
+			ONENAND_SET_BUFFERRAM0(this);
+		else
+			/* Switch to the next data buffer */
+			ONENAND_SET_NEXT_BUFFERRAM(this);
+
+		return 0;
+	}
+
+	if (block != -1) {
+		/* Write 'DFS, FBA' of Flash */
+		value = onenand_block_address(this, block);
+		this->write_word(value, this->base + ONENAND_REG_START_ADDRESS1);
+
+		/* Select DataRAM for DDP */
+		value = onenand_bufferram_address(this, block);
+		this->write_word(value, this->base + ONENAND_REG_START_ADDRESS2);
+	}
+
+	if (page != -1) {
+		/* Now we use page size operation */
+		int sectors = 0, count = 0;
+		int dataram;
+
+		switch (cmd) {
+		case FLEXONENAND_CMD_RECOVER_LSB:
+		case ONENAND_CMD_READ:
+		case ONENAND_CMD_READOOB:
+			if (ONENAND_IS_4KB_PAGE(this))
+				/* It is always BufferRAM0 */
+				dataram = ONENAND_SET_BUFFERRAM0(this);
+			else
+				dataram = ONENAND_SET_NEXT_BUFFERRAM(this);
+			break;
+
+		default:
+			if (ONENAND_IS_2PLANE(this) && cmd == ONENAND_CMD_PROG)
+				cmd = ONENAND_CMD_2X_PROG;
+			dataram = ONENAND_CURRENT_BUFFERRAM(this);
+			break;
+		}
+
+		/* Write 'FPA, FSA' of Flash */
+		value = onenand_page_address(page, sectors);
+		this->write_word(value, this->base + ONENAND_REG_START_ADDRESS8);
+
+		/* Write 'BSA, BSC' of DataRAM */
+		value = onenand_buffer_address(dataram, sectors, count);
+		this->write_word(value, this->base + ONENAND_REG_START_BUFFER);
+	}
+
+	/* Interrupt clear */
+	this->write_word(ONENAND_INT_CLEAR, this->base + ONENAND_REG_INTERRUPT);
+
+	/* Write command */
+	this->write_word(cmd, this->base + ONENAND_REG_COMMAND);
+
+	return 0;
+}
+
+/**
+ * onenand_read_ecc - return ecc status
+ * @param this		onenand chip structure
+ */
+static inline int onenand_read_ecc(struct onenand_chip *this)
+{
+	int ecc, i, result = 0;
+
+	if (!FLEXONENAND(this) && !ONENAND_IS_4KB_PAGE(this))
+		return this->read_word(this->base + ONENAND_REG_ECC_STATUS);
+
+	for (i = 0; i < 4; i++) {
+		ecc = this->read_word(this->base + ONENAND_REG_ECC_STATUS + i*2);
+		if (likely(!ecc))
+			continue;
+		if (ecc & FLEXONENAND_UNCORRECTABLE_ERROR)
+			return ONENAND_ECC_2BIT_ALL;
+		else
+			result = ONENAND_ECC_1BIT_ALL;
+	}
+
+	return result;
+}
+
+/**
+ * onenand_wait - [DEFAULT] wait until the command is done
+ * @param mtd		MTD device structure
+ * @param state		state to select the max. timeout value
+ *
+ * Wait for command done. This applies to all OneNAND command
+ * Read can take up to 30us, erase up to 2ms and program up to 350us
+ * according to general OneNAND specs
+ */
+static int onenand_wait(struct mtd_info *mtd, int state)
+{
+	struct onenand_chip * this = mtd->priv;
+	unsigned long timeout;
+	unsigned int flags = ONENAND_INT_MASTER;
+	unsigned int interrupt = 0;
+	unsigned int ctrl;
+
+	/* The 20 msec is enough */
+	timeout = jiffies + msecs_to_jiffies(20);
+	while (time_before(jiffies, timeout)) {
+		interrupt = this->read_word(this->base + ONENAND_REG_INTERRUPT);
+
+		if (interrupt & flags)
+			break;
+
+		if (state != FL_READING && state != FL_PREPARING_ERASE)
+			cond_resched();
+	}
+	/* To get correct interrupt status in timeout case */
+	interrupt = this->read_word(this->base + ONENAND_REG_INTERRUPT);
+
+	ctrl = this->read_word(this->base + ONENAND_REG_CTRL_STATUS);
+
+	/*
+	 * In the Spec. it checks the controller status first
+	 * However if you get the correct information in case of
+	 * power off recovery (POR) test, it should read ECC status first
+	 */
+	if (interrupt & ONENAND_INT_READ) {
+		int ecc = onenand_read_ecc(this);
+		if (ecc) {
+			if (ecc & ONENAND_ECC_2BIT_ALL) {
+				printk(KERN_ERR "%s: ECC error = 0x%04x\n",
+					__func__, ecc);
+				mtd->ecc_stats.failed++;
+				return -EBADMSG;
+			} else if (ecc & ONENAND_ECC_1BIT_ALL) {
+				printk(KERN_DEBUG "%s: correctable ECC error = 0x%04x\n",
+					__func__, ecc);
+				mtd->ecc_stats.corrected++;
+			}
+		}
+	} else if (state == FL_READING) {
+		printk(KERN_ERR "%s: read timeout! ctrl=0x%04x intr=0x%04x\n",
+			__func__, ctrl, interrupt);
+		return -EIO;
+	}
+
+	if (state == FL_PREPARING_ERASE && !(interrupt & ONENAND_INT_ERASE)) {
+		printk(KERN_ERR "%s: mb erase timeout! ctrl=0x%04x intr=0x%04x\n",
+		       __func__, ctrl, interrupt);
+		return -EIO;
+	}
+
+	if (!(interrupt & ONENAND_INT_MASTER)) {
+		printk(KERN_ERR "%s: timeout! ctrl=0x%04x intr=0x%04x\n",
+		       __func__, ctrl, interrupt);
+		return -EIO;
+	}
+
+	/* If there's controller error, it's a real error */
+	if (ctrl & ONENAND_CTRL_ERROR) {
+		printk(KERN_ERR "%s: controller error = 0x%04x\n",
+			__func__, ctrl);
+		if (ctrl & ONENAND_CTRL_LOCK)
+			printk(KERN_ERR "%s: it's locked error.\n", __func__);
+		return -EIO;
+	}
+
+	return 0;
+}
+
+/*
+ * onenand_interrupt - [DEFAULT] onenand interrupt handler
+ * @param irq		onenand interrupt number
+ * @param dev_id	interrupt data
+ *
+ * complete the work
+ */
+static irqreturn_t onenand_interrupt(int irq, void *data)
+{
+	struct onenand_chip *this = data;
+
+	/* To handle shared interrupt */
+	if (!this->complete.done)
+		complete(&this->complete);
+
+	return IRQ_HANDLED;
+}
+
+/*
+ * onenand_interrupt_wait - [DEFAULT] wait until the command is done
+ * @param mtd		MTD device structure
+ * @param state		state to select the max. timeout value
+ *
+ * Wait for command done.
+ */
+static int onenand_interrupt_wait(struct mtd_info *mtd, int state)
+{
+	struct onenand_chip *this = mtd->priv;
+
+	wait_for_completion(&this->complete);
+
+	return onenand_wait(mtd, state);
+}
+
+/*
+ * onenand_try_interrupt_wait - [DEFAULT] try interrupt wait
+ * @param mtd		MTD device structure
+ * @param state		state to select the max. timeout value
+ *
+ * Try interrupt based wait (It is used one-time)
+ */
+static int onenand_try_interrupt_wait(struct mtd_info *mtd, int state)
+{
+	struct onenand_chip *this = mtd->priv;
+	unsigned long remain, timeout;
+
+	/* We use interrupt wait first */
+	this->wait = onenand_interrupt_wait;
+
+	timeout = msecs_to_jiffies(100);
+	remain = wait_for_completion_timeout(&this->complete, timeout);
+	if (!remain) {
+		printk(KERN_INFO "OneNAND: There's no interrupt. "
+				"We use the normal wait\n");
+
+		/* Release the irq */
+		free_irq(this->irq, this);
+
+		this->wait = onenand_wait;
+	}
+
+	return onenand_wait(mtd, state);
+}
+
+/*
+ * onenand_setup_wait - [OneNAND Interface] setup onenand wait method
+ * @param mtd		MTD device structure
+ *
+ * There's two method to wait onenand work
+ * 1. polling - read interrupt status register
+ * 2. interrupt - use the kernel interrupt method
+ */
+static void onenand_setup_wait(struct mtd_info *mtd)
+{
+	struct onenand_chip *this = mtd->priv;
+	int syscfg;
+
+	init_completion(&this->complete);
+
+	if (this->irq <= 0) {
+		this->wait = onenand_wait;
+		return;
+	}
+
+	if (request_irq(this->irq, &onenand_interrupt,
+				IRQF_SHARED, "onenand", this)) {
+		/* If we can't get irq, use the normal wait */
+		this->wait = onenand_wait;
+		return;
+	}
+
+	/* Enable interrupt */
+	syscfg = this->read_word(this->base + ONENAND_REG_SYS_CFG1);
+	syscfg |= ONENAND_SYS_CFG1_IOBE;
+	this->write_word(syscfg, this->base + ONENAND_REG_SYS_CFG1);
+
+	this->wait = onenand_try_interrupt_wait;
+}
+
+/**
+ * onenand_bufferram_offset - [DEFAULT] BufferRAM offset
+ * @param mtd		MTD data structure
+ * @param area		BufferRAM area
+ * @return		offset given area
+ *
+ * Return BufferRAM offset given area
+ */
+static inline int onenand_bufferram_offset(struct mtd_info *mtd, int area)
+{
+	struct onenand_chip *this = mtd->priv;
+
+	if (ONENAND_CURRENT_BUFFERRAM(this)) {
+		/* Note: the 'this->writesize' is a real page size */
+		if (area == ONENAND_DATARAM)
+			return this->writesize;
+		if (area == ONENAND_SPARERAM)
+			return mtd->oobsize;
+	}
+
+	return 0;
+}
+
+/**
+ * onenand_read_bufferram - [OneNAND Interface] Read the bufferram area
+ * @param mtd		MTD data structure
+ * @param area		BufferRAM area
+ * @param buffer	the databuffer to put/get data
+ * @param offset	offset to read from or write to
+ * @param count		number of bytes to read/write
+ *
+ * Read the BufferRAM area
+ */
+static int onenand_read_bufferram(struct mtd_info *mtd, int area,
+		unsigned char *buffer, int offset, size_t count)
+{
+	struct onenand_chip *this = mtd->priv;
+	void __iomem *bufferram;
+
+	bufferram = this->base + area;
+
+	bufferram += onenand_bufferram_offset(mtd, area);
+
+	if (ONENAND_CHECK_BYTE_ACCESS(count)) {
+		unsigned short word;
+
+		/* Align with word(16-bit) size */
+		count--;
+
+		/* Read word and save byte */
+		word = this->read_word(bufferram + offset + count);
+		buffer[count] = (word & 0xff);
+	}
+
+	memcpy(buffer, bufferram + offset, count);
+
+	return 0;
+}
+
+/**
+ * onenand_sync_read_bufferram - [OneNAND Interface] Read the bufferram area with Sync. Burst mode
+ * @param mtd		MTD data structure
+ * @param area		BufferRAM area
+ * @param buffer	the databuffer to put/get data
+ * @param offset	offset to read from or write to
+ * @param count		number of bytes to read/write
+ *
+ * Read the BufferRAM area with Sync. Burst Mode
+ */
+static int onenand_sync_read_bufferram(struct mtd_info *mtd, int area,
+		unsigned char *buffer, int offset, size_t count)
+{
+	struct onenand_chip *this = mtd->priv;
+	void __iomem *bufferram;
+
+	bufferram = this->base + area;
+
+	bufferram += onenand_bufferram_offset(mtd, area);
+
+	this->mmcontrol(mtd, ONENAND_SYS_CFG1_SYNC_READ);
+
+	if (ONENAND_CHECK_BYTE_ACCESS(count)) {
+		unsigned short word;
+
+		/* Align with word(16-bit) size */
+		count--;
+
+		/* Read word and save byte */
+		word = this->read_word(bufferram + offset + count);
+		buffer[count] = (word & 0xff);
+	}
+
+	memcpy(buffer, bufferram + offset, count);
+
+	this->mmcontrol(mtd, 0);
+
+	return 0;
+}
+
+/**
+ * onenand_write_bufferram - [OneNAND Interface] Write the bufferram area
+ * @param mtd		MTD data structure
+ * @param area		BufferRAM area
+ * @param buffer	the databuffer to put/get data
+ * @param offset	offset to read from or write to
+ * @param count		number of bytes to read/write
+ *
+ * Write the BufferRAM area
+ */
+static int onenand_write_bufferram(struct mtd_info *mtd, int area,
+		const unsigned char *buffer, int offset, size_t count)
+{
+	struct onenand_chip *this = mtd->priv;
+	void __iomem *bufferram;
+
+	bufferram = this->base + area;
+
+	bufferram += onenand_bufferram_offset(mtd, area);
+
+	if (ONENAND_CHECK_BYTE_ACCESS(count)) {
+		unsigned short word;
+		int byte_offset;
+
+		/* Align with word(16-bit) size */
+		count--;
+
+		/* Calculate byte access offset */
+		byte_offset = offset + count;
+
+		/* Read word and save byte */
+		word = this->read_word(bufferram + byte_offset);
+		word = (word & ~0xff) | buffer[count];
+		this->write_word(word, bufferram + byte_offset);
+	}
+
+	memcpy(bufferram + offset, buffer, count);
+
+	return 0;
+}
+
+/**
+ * onenand_get_2x_blockpage - [GENERIC] Get blockpage at 2x program mode
+ * @param mtd		MTD data structure
+ * @param addr		address to check
+ * @return		blockpage address
+ *
+ * Get blockpage address at 2x program mode
+ */
+static int onenand_get_2x_blockpage(struct mtd_info *mtd, loff_t addr)
+{
+	struct onenand_chip *this = mtd->priv;
+	int blockpage, block, page;
+
+	/* Calculate the even block number */
+	block = (int) (addr >> this->erase_shift) & ~1;
+	/* Is it the odd plane? */
+	if (addr & this->writesize)
+		block++;
+	page = (int) (addr >> (this->page_shift + 1)) & this->page_mask;
+	blockpage = (block << 7) | page;
+
+	return blockpage;
+}
+
+/**
+ * onenand_check_bufferram - [GENERIC] Check BufferRAM information
+ * @param mtd		MTD data structure
+ * @param addr		address to check
+ * @return		1 if there are valid data, otherwise 0
+ *
+ * Check bufferram if there is data we required
+ */
+static int onenand_check_bufferram(struct mtd_info *mtd, loff_t addr)
+{
+	struct onenand_chip *this = mtd->priv;
+	int blockpage, found = 0;
+	unsigned int i;
+
+	if (ONENAND_IS_2PLANE(this))
+		blockpage = onenand_get_2x_blockpage(mtd, addr);
+	else
+		blockpage = (int) (addr >> this->page_shift);
+
+	/* Is there valid data? */
+	i = ONENAND_CURRENT_BUFFERRAM(this);
+	if (this->bufferram[i].blockpage == blockpage)
+		found = 1;
+	else {
+		/* Check another BufferRAM */
+		i = ONENAND_NEXT_BUFFERRAM(this);
+		if (this->bufferram[i].blockpage == blockpage) {
+			ONENAND_SET_NEXT_BUFFERRAM(this);
+			found = 1;
+		}
+	}
+
+	if (found && ONENAND_IS_DDP(this)) {
+		/* Select DataRAM for DDP */
+		int block = onenand_block(this, addr);
+		int value = onenand_bufferram_address(this, block);
+		this->write_word(value, this->base + ONENAND_REG_START_ADDRESS2);
+	}
+
+	return found;
+}
+
+/**
+ * onenand_update_bufferram - [GENERIC] Update BufferRAM information
+ * @param mtd		MTD data structure
+ * @param addr		address to update
+ * @param valid		valid flag
+ *
+ * Update BufferRAM information
+ */
+static void onenand_update_bufferram(struct mtd_info *mtd, loff_t addr,
+		int valid)
+{
+	struct onenand_chip *this = mtd->priv;
+	int blockpage;
+	unsigned int i;
+
+	if (ONENAND_IS_2PLANE(this))
+		blockpage = onenand_get_2x_blockpage(mtd, addr);
+	else
+		blockpage = (int) (addr >> this->page_shift);
+
+	/* Invalidate another BufferRAM */
+	i = ONENAND_NEXT_BUFFERRAM(this);
+	if (this->bufferram[i].blockpage == blockpage)
+		this->bufferram[i].blockpage = -1;
+
+	/* Update BufferRAM */
+	i = ONENAND_CURRENT_BUFFERRAM(this);
+	if (valid)
+		this->bufferram[i].blockpage = blockpage;
+	else
+		this->bufferram[i].blockpage = -1;
+}
+
+/**
+ * onenand_invalidate_bufferram - [GENERIC] Invalidate BufferRAM information
+ * @param mtd		MTD data structure
+ * @param addr		start address to invalidate
+ * @param len		length to invalidate
+ *
+ * Invalidate BufferRAM information
+ */
+static void onenand_invalidate_bufferram(struct mtd_info *mtd, loff_t addr,
+		unsigned int len)
+{
+	struct onenand_chip *this = mtd->priv;
+	int i;
+	loff_t end_addr = addr + len;
+
+	/* Invalidate BufferRAM */
+	for (i = 0; i < MAX_BUFFERRAM; i++) {
+		loff_t buf_addr = this->bufferram[i].blockpage << this->page_shift;
+		if (buf_addr >= addr && buf_addr < end_addr)
+			this->bufferram[i].blockpage = -1;
+	}
+}
+
+/**
+ * onenand_get_device - [GENERIC] Get chip for selected access
+ * @param mtd		MTD device structure
+ * @param new_state	the state which is requested
+ *
+ * Get the device and lock it for exclusive access
+ */
+static int onenand_get_device(struct mtd_info *mtd, int new_state)
+{
+	struct onenand_chip *this = mtd->priv;
+	DECLARE_WAITQUEUE(wait, current);
+
+	/*
+	 * Grab the lock and see if the device is available
+	 */
+	while (1) {
+		spin_lock(&this->chip_lock);
+		if (this->state == FL_READY) {
+			this->state = new_state;
+			spin_unlock(&this->chip_lock);
+			if (new_state != FL_PM_SUSPENDED && this->enable)
+				this->enable(mtd);
+			break;
+		}
+		if (new_state == FL_PM_SUSPENDED) {
+			spin_unlock(&this->chip_lock);
+			return (this->state == FL_PM_SUSPENDED) ? 0 : -EAGAIN;
+		}
+		set_current_state(TASK_UNINTERRUPTIBLE);
+		add_wait_queue(&this->wq, &wait);
+		spin_unlock(&this->chip_lock);
+		schedule();
+		remove_wait_queue(&this->wq, &wait);
+	}
+
+	return 0;
+}
+
+/**
+ * onenand_release_device - [GENERIC] release chip
+ * @param mtd		MTD device structure
+ *
+ * Deselect, release chip lock and wake up anyone waiting on the device
+ */
+static void onenand_release_device(struct mtd_info *mtd)
+{
+	struct onenand_chip *this = mtd->priv;
+
+	if (this->state != FL_PM_SUSPENDED && this->disable)
+		this->disable(mtd);
+	/* Release the chip */
+	spin_lock(&this->chip_lock);
+	this->state = FL_READY;
+	wake_up(&this->wq);
+	spin_unlock(&this->chip_lock);
+}
+
+/**
+ * onenand_transfer_auto_oob - [INTERN] oob auto-placement transfer
+ * @param mtd		MTD device structure
+ * @param buf		destination address
+ * @param column	oob offset to read from
+ * @param thislen	oob length to read
+ */
+static int onenand_transfer_auto_oob(struct mtd_info *mtd, uint8_t *buf, int column,
+				int thislen)
+{
+	struct onenand_chip *this = mtd->priv;
+	int ret;
+
+	this->read_bufferram(mtd, ONENAND_SPARERAM, this->oob_buf, 0,
+			     mtd->oobsize);
+	ret = mtd_ooblayout_get_databytes(mtd, buf, this->oob_buf,
+					  column, thislen);
+	if (ret)
+		return ret;
+
+	return 0;
+}
+
+/**
+ * onenand_recover_lsb - [Flex-OneNAND] Recover LSB page data
+ * @param mtd		MTD device structure
+ * @param addr		address to recover
+ * @param status	return value from onenand_wait / onenand_bbt_wait
+ *
+ * MLC NAND Flash cell has paired pages - LSB page and MSB page. LSB page has
+ * lower page address and MSB page has higher page address in paired pages.
+ * If power off occurs during MSB page program, the paired LSB page data can
+ * become corrupt. LSB page recovery read is a way to read LSB page though page
+ * data are corrupted. When uncorrectable error occurs as a result of LSB page
+ * read after power up, issue LSB page recovery read.
+ */
+static int onenand_recover_lsb(struct mtd_info *mtd, loff_t addr, int status)
+{
+	struct onenand_chip *this = mtd->priv;
+	int i;
+
+	/* Recovery is only for Flex-OneNAND */
+	if (!FLEXONENAND(this))
+		return status;
+
+	/* check if we failed due to uncorrectable error */
+	if (!mtd_is_eccerr(status) && status != ONENAND_BBT_READ_ECC_ERROR)
+		return status;
+
+	/* check if address lies in MLC region */
+	i = flexonenand_region(mtd, addr);
+	if (mtd->eraseregions[i].erasesize < (1 << this->erase_shift))
+		return status;
+
+	/* We are attempting to reread, so decrement stats.failed
+	 * which was incremented by onenand_wait due to read failure
+	 */
+	printk(KERN_INFO "%s: Attempting to recover from uncorrectable read\n",
+		__func__);
+	mtd->ecc_stats.failed--;
+
+	/* Issue the LSB page recovery command */
+	this->command(mtd, FLEXONENAND_CMD_RECOVER_LSB, addr, this->writesize);
+	return this->wait(mtd, FL_READING);
+}
+
+/**
+ * onenand_mlc_read_ops_nolock - MLC OneNAND read main and/or out-of-band
+ * @param mtd		MTD device structure
+ * @param from		offset to read from
+ * @param ops:		oob operation description structure
+ *
+ * MLC OneNAND / Flex-OneNAND has 4KB page size and 4KB dataram.
+ * So, read-while-load is not present.
+ */
+static int onenand_mlc_read_ops_nolock(struct mtd_info *mtd, loff_t from,
+				struct mtd_oob_ops *ops)
+{
+	struct onenand_chip *this = mtd->priv;
+	struct mtd_ecc_stats stats;
+	size_t len = ops->len;
+	size_t ooblen = ops->ooblen;
+	u_char *buf = ops->datbuf;
+	u_char *oobbuf = ops->oobbuf;
+	int read = 0, column, thislen;
+	int oobread = 0, oobcolumn, thisooblen, oobsize;
+	int ret = 0;
+	int writesize = this->writesize;
+
+	pr_debug("%s: from = 0x%08x, len = %i\n", __func__, (unsigned int)from,
+			(int)len);
+
+	oobsize = mtd_oobavail(mtd, ops);
+	oobcolumn = from & (mtd->oobsize - 1);
+
+	/* Do not allow reads past end of device */
+	if (from + len > mtd->size) {
+		printk(KERN_ERR "%s: Attempt read beyond end of device\n",
+			__func__);
+		ops->retlen = 0;
+		ops->oobretlen = 0;
+		return -EINVAL;
+	}
+
+	stats = mtd->ecc_stats;
+
+	while (read < len) {
+		cond_resched();
+
+		thislen = min_t(int, writesize, len - read);
+
+		column = from & (writesize - 1);
+		if (column + thislen > writesize)
+			thislen = writesize - column;
+
+		if (!onenand_check_bufferram(mtd, from)) {
+			this->command(mtd, ONENAND_CMD_READ, from, writesize);
+
+			ret = this->wait(mtd, FL_READING);
+			if (unlikely(ret))
+				ret = onenand_recover_lsb(mtd, from, ret);
+			onenand_update_bufferram(mtd, from, !ret);
+			if (mtd_is_eccerr(ret))
+				ret = 0;
+			if (ret)
+				break;
+		}
+
+		this->read_bufferram(mtd, ONENAND_DATARAM, buf, column, thislen);
+		if (oobbuf) {
+			thisooblen = oobsize - oobcolumn;
+			thisooblen = min_t(int, thisooblen, ooblen - oobread);
+
+			if (ops->mode == MTD_OPS_AUTO_OOB)
+				onenand_transfer_auto_oob(mtd, oobbuf, oobcolumn, thisooblen);
+			else
+				this->read_bufferram(mtd, ONENAND_SPARERAM, oobbuf, oobcolumn, thisooblen);
+			oobread += thisooblen;
+			oobbuf += thisooblen;
+			oobcolumn = 0;
+		}
+
+		read += thislen;
+		if (read == len)
+			break;
+
+		from += thislen;
+		buf += thislen;
+	}
+
+	/*
+	 * Return success, if no ECC failures, else -EBADMSG
+	 * fs driver will take care of that, because
+	 * retlen == desired len and result == -EBADMSG
+	 */
+	ops->retlen = read;
+	ops->oobretlen = oobread;
+
+	if (ret)
+		return ret;
+
+	if (mtd->ecc_stats.failed - stats.failed)
+		return -EBADMSG;
+
+	/* return max bitflips per ecc step; ONENANDs correct 1 bit only */
+	return mtd->ecc_stats.corrected != stats.corrected ? 1 : 0;
+}
+
+/**
+ * onenand_read_ops_nolock - [OneNAND Interface] OneNAND read main and/or out-of-band
+ * @param mtd		MTD device structure
+ * @param from		offset to read from
+ * @param ops:		oob operation description structure
+ *
+ * OneNAND read main and/or out-of-band data
+ */
+static int onenand_read_ops_nolock(struct mtd_info *mtd, loff_t from,
+				struct mtd_oob_ops *ops)
+{
+	struct onenand_chip *this = mtd->priv;
+	struct mtd_ecc_stats stats;
+	size_t len = ops->len;
+	size_t ooblen = ops->ooblen;
+	u_char *buf = ops->datbuf;
+	u_char *oobbuf = ops->oobbuf;
+	int read = 0, column, thislen;
+	int oobread = 0, oobcolumn, thisooblen, oobsize;
+	int ret = 0, boundary = 0;
+	int writesize = this->writesize;
+
+	pr_debug("%s: from = 0x%08x, len = %i\n", __func__, (unsigned int)from,
+			(int)len);
+
+	oobsize = mtd_oobavail(mtd, ops);
+	oobcolumn = from & (mtd->oobsize - 1);
+
+	/* Do not allow reads past end of device */
+	if ((from + len) > mtd->size) {
+		printk(KERN_ERR "%s: Attempt read beyond end of device\n",
+			__func__);
+		ops->retlen = 0;
+		ops->oobretlen = 0;
+		return -EINVAL;
+	}
+
+	stats = mtd->ecc_stats;
+
+ 	/* Read-while-load method */
+
+ 	/* Do first load to bufferRAM */
+ 	if (read < len) {
+ 		if (!onenand_check_bufferram(mtd, from)) {
+			this->command(mtd, ONENAND_CMD_READ, from, writesize);
+ 			ret = this->wait(mtd, FL_READING);
+ 			onenand_update_bufferram(mtd, from, !ret);
+			if (mtd_is_eccerr(ret))
+				ret = 0;
+ 		}
+ 	}
+
+	thislen = min_t(int, writesize, len - read);
+	column = from & (writesize - 1);
+	if (column + thislen > writesize)
+		thislen = writesize - column;
+
+ 	while (!ret) {
+ 		/* If there is more to load then start next load */
+ 		from += thislen;
+ 		if (read + thislen < len) {
+			this->command(mtd, ONENAND_CMD_READ, from, writesize);
+ 			/*
+ 			 * Chip boundary handling in DDP
+ 			 * Now we issued chip 1 read and pointed chip 1
+			 * bufferram so we have to point chip 0 bufferram.
+ 			 */
+ 			if (ONENAND_IS_DDP(this) &&
+ 			    unlikely(from == (this->chipsize >> 1))) {
+ 				this->write_word(ONENAND_DDP_CHIP0, this->base + ONENAND_REG_START_ADDRESS2);
+ 				boundary = 1;
+ 			} else
+ 				boundary = 0;
+ 			ONENAND_SET_PREV_BUFFERRAM(this);
+ 		}
+ 		/* While load is going, read from last bufferRAM */
+ 		this->read_bufferram(mtd, ONENAND_DATARAM, buf, column, thislen);
+
+		/* Read oob area if needed */
+		if (oobbuf) {
+			thisooblen = oobsize - oobcolumn;
+			thisooblen = min_t(int, thisooblen, ooblen - oobread);
+
+			if (ops->mode == MTD_OPS_AUTO_OOB)
+				onenand_transfer_auto_oob(mtd, oobbuf, oobcolumn, thisooblen);
+			else
+				this->read_bufferram(mtd, ONENAND_SPARERAM, oobbuf, oobcolumn, thisooblen);
+			oobread += thisooblen;
+			oobbuf += thisooblen;
+			oobcolumn = 0;
+		}
+
+ 		/* See if we are done */
+ 		read += thislen;
+ 		if (read == len)
+ 			break;
+ 		/* Set up for next read from bufferRAM */
+ 		if (unlikely(boundary))
+ 			this->write_word(ONENAND_DDP_CHIP1, this->base + ONENAND_REG_START_ADDRESS2);
+ 		ONENAND_SET_NEXT_BUFFERRAM(this);
+ 		buf += thislen;
+		thislen = min_t(int, writesize, len - read);
+ 		column = 0;
+ 		cond_resched();
+ 		/* Now wait for load */
+ 		ret = this->wait(mtd, FL_READING);
+ 		onenand_update_bufferram(mtd, from, !ret);
+		if (mtd_is_eccerr(ret))
+			ret = 0;
+ 	}
+
+	/*
+	 * Return success, if no ECC failures, else -EBADMSG
+	 * fs driver will take care of that, because
+	 * retlen == desired len and result == -EBADMSG
+	 */
+	ops->retlen = read;
+	ops->oobretlen = oobread;
+
+	if (ret)
+		return ret;
+
+	if (mtd->ecc_stats.failed - stats.failed)
+		return -EBADMSG;
+
+	/* return max bitflips per ecc step; ONENANDs correct 1 bit only */
+	return mtd->ecc_stats.corrected != stats.corrected ? 1 : 0;
+}
+
+/**
+ * onenand_read_oob_nolock - [MTD Interface] OneNAND read out-of-band
+ * @param mtd		MTD device structure
+ * @param from		offset to read from
+ * @param ops:		oob operation description structure
+ *
+ * OneNAND read out-of-band data from the spare area
+ */
+static int onenand_read_oob_nolock(struct mtd_info *mtd, loff_t from,
+			struct mtd_oob_ops *ops)
+{
+	struct onenand_chip *this = mtd->priv;
+	struct mtd_ecc_stats stats;
+	int read = 0, thislen, column, oobsize;
+	size_t len = ops->ooblen;
+	unsigned int mode = ops->mode;
+	u_char *buf = ops->oobbuf;
+	int ret = 0, readcmd;
+
+	from += ops->ooboffs;
+
+	pr_debug("%s: from = 0x%08x, len = %i\n", __func__, (unsigned int)from,
+			(int)len);
+
+	/* Initialize return length value */
+	ops->oobretlen = 0;
+
+	if (mode == MTD_OPS_AUTO_OOB)
+		oobsize = mtd->oobavail;
+	else
+		oobsize = mtd->oobsize;
+
+	column = from & (mtd->oobsize - 1);
+
+	if (unlikely(column >= oobsize)) {
+		printk(KERN_ERR "%s: Attempted to start read outside oob\n",
+			__func__);
+		return -EINVAL;
+	}
+
+	stats = mtd->ecc_stats;
+
+	readcmd = ONENAND_IS_4KB_PAGE(this) ? ONENAND_CMD_READ : ONENAND_CMD_READOOB;
+
+	while (read < len) {
+		cond_resched();
+
+		thislen = oobsize - column;
+		thislen = min_t(int, thislen, len);
+
+		this->command(mtd, readcmd, from, mtd->oobsize);
+
+		onenand_update_bufferram(mtd, from, 0);
+
+		ret = this->wait(mtd, FL_READING);
+		if (unlikely(ret))
+			ret = onenand_recover_lsb(mtd, from, ret);
+
+		if (ret && !mtd_is_eccerr(ret)) {
+			printk(KERN_ERR "%s: read failed = 0x%x\n",
+				__func__, ret);
+			break;
+		}
+
+		if (mode == MTD_OPS_AUTO_OOB)
+			onenand_transfer_auto_oob(mtd, buf, column, thislen);
+		else
+			this->read_bufferram(mtd, ONENAND_SPARERAM, buf, column, thislen);
+
+		read += thislen;
+
+		if (read == len)
+			break;
+
+		buf += thislen;
+
+		/* Read more? */
+		if (read < len) {
+			/* Page size */
+			from += mtd->writesize;
+			column = 0;
+		}
+	}
+
+	ops->oobretlen = read;
+
+	if (ret)
+		return ret;
+
+	if (mtd->ecc_stats.failed - stats.failed)
+		return -EBADMSG;
+
+	return 0;
+}
+
+/**
+ * onenand_read_oob - [MTD Interface] Read main and/or out-of-band
+ * @param mtd:		MTD device structure
+ * @param from:		offset to read from
+ * @param ops:		oob operation description structure
+
+ * Read main and/or out-of-band
+ */
+static int onenand_read_oob(struct mtd_info *mtd, loff_t from,
+			    struct mtd_oob_ops *ops)
+{
+	struct onenand_chip *this = mtd->priv;
+	int ret;
+
+	switch (ops->mode) {
+	case MTD_OPS_PLACE_OOB:
+	case MTD_OPS_AUTO_OOB:
+		break;
+	case MTD_OPS_RAW:
+		/* Not implemented yet */
+	default:
+		return -EINVAL;
+	}
+
+	onenand_get_device(mtd, FL_READING);
+	if (ops->datbuf)
+		ret = ONENAND_IS_4KB_PAGE(this) ?
+			onenand_mlc_read_ops_nolock(mtd, from, ops) :
+			onenand_read_ops_nolock(mtd, from, ops);
+	else
+		ret = onenand_read_oob_nolock(mtd, from, ops);
+	onenand_release_device(mtd);
+
+	return ret;
+}
+
+/**
+ * onenand_bbt_wait - [DEFAULT] wait until the command is done
+ * @param mtd		MTD device structure
+ * @param state		state to select the max. timeout value
+ *
+ * Wait for command done.
+ */
+static int onenand_bbt_wait(struct mtd_info *mtd, int state)
+{
+	struct onenand_chip *this = mtd->priv;
+	unsigned long timeout;
+	unsigned int interrupt, ctrl, ecc, addr1, addr8;
+
+	/* The 20 msec is enough */
+	timeout = jiffies + msecs_to_jiffies(20);
+	while (time_before(jiffies, timeout)) {
+		interrupt = this->read_word(this->base + ONENAND_REG_INTERRUPT);
+		if (interrupt & ONENAND_INT_MASTER)
+			break;
+	}
+	/* To get correct interrupt status in timeout case */
+	interrupt = this->read_word(this->base + ONENAND_REG_INTERRUPT);
+	ctrl = this->read_word(this->base + ONENAND_REG_CTRL_STATUS);
+	addr1 = this->read_word(this->base + ONENAND_REG_START_ADDRESS1);
+	addr8 = this->read_word(this->base + ONENAND_REG_START_ADDRESS8);
+
+	if (interrupt & ONENAND_INT_READ) {
+		ecc = onenand_read_ecc(this);
+		if (ecc & ONENAND_ECC_2BIT_ALL) {
+			printk(KERN_DEBUG "%s: ecc 0x%04x ctrl 0x%04x "
+			       "intr 0x%04x addr1 %#x addr8 %#x\n",
+			       __func__, ecc, ctrl, interrupt, addr1, addr8);
+			return ONENAND_BBT_READ_ECC_ERROR;
+		}
+	} else {
+		printk(KERN_ERR "%s: read timeout! ctrl 0x%04x "
+		       "intr 0x%04x addr1 %#x addr8 %#x\n",
+		       __func__, ctrl, interrupt, addr1, addr8);
+		return ONENAND_BBT_READ_FATAL_ERROR;
+	}
+
+	/* Initial bad block case: 0x2400 or 0x0400 */
+	if (ctrl & ONENAND_CTRL_ERROR) {
+		printk(KERN_DEBUG "%s: ctrl 0x%04x intr 0x%04x addr1 %#x "
+		       "addr8 %#x\n", __func__, ctrl, interrupt, addr1, addr8);
+		return ONENAND_BBT_READ_ERROR;
+	}
+
+	return 0;
+}
+
+/**
+ * onenand_bbt_read_oob - [MTD Interface] OneNAND read out-of-band for bbt scan
+ * @param mtd		MTD device structure
+ * @param from		offset to read from
+ * @param ops		oob operation description structure
+ *
+ * OneNAND read out-of-band data from the spare area for bbt scan
+ */
+int onenand_bbt_read_oob(struct mtd_info *mtd, loff_t from, 
+			    struct mtd_oob_ops *ops)
+{
+	struct onenand_chip *this = mtd->priv;
+	int read = 0, thislen, column;
+	int ret = 0, readcmd;
+	size_t len = ops->ooblen;
+	u_char *buf = ops->oobbuf;
+
+	pr_debug("%s: from = 0x%08x, len = %zi\n", __func__, (unsigned int)from,
+			len);
+
+	/* Initialize return value */
+	ops->oobretlen = 0;
+
+	/* Do not allow reads past end of device */
+	if (unlikely((from + len) > mtd->size)) {
+		printk(KERN_ERR "%s: Attempt read beyond end of device\n",
+			__func__);
+		return ONENAND_BBT_READ_FATAL_ERROR;
+	}
+
+	/* Grab the lock and see if the device is available */
+	onenand_get_device(mtd, FL_READING);
+
+	column = from & (mtd->oobsize - 1);
+
+	readcmd = ONENAND_IS_4KB_PAGE(this) ? ONENAND_CMD_READ : ONENAND_CMD_READOOB;
+
+	while (read < len) {
+		cond_resched();
+
+		thislen = mtd->oobsize - column;
+		thislen = min_t(int, thislen, len);
+
+		this->command(mtd, readcmd, from, mtd->oobsize);
+
+		onenand_update_bufferram(mtd, from, 0);
+
+		ret = this->bbt_wait(mtd, FL_READING);
+		if (unlikely(ret))
+			ret = onenand_recover_lsb(mtd, from, ret);
+
+		if (ret)
+			break;
+
+		this->read_bufferram(mtd, ONENAND_SPARERAM, buf, column, thislen);
+		read += thislen;
+		if (read == len)
+			break;
+
+		buf += thislen;
+
+		/* Read more? */
+		if (read < len) {
+			/* Update Page size */
+			from += this->writesize;
+			column = 0;
+		}
+	}
+
+	/* Deselect and wake up anyone waiting on the device */
+	onenand_release_device(mtd);
+
+	ops->oobretlen = read;
+	return ret;
+}
+
+#ifdef CONFIG_MTD_ONENAND_VERIFY_WRITE
+/**
+ * onenand_verify_oob - [GENERIC] verify the oob contents after a write
+ * @param mtd		MTD device structure
+ * @param buf		the databuffer to verify
+ * @param to		offset to read from
+ */
+static int onenand_verify_oob(struct mtd_info *mtd, const u_char *buf, loff_t to)
+{
+	struct onenand_chip *this = mtd->priv;
+	u_char *oob_buf = this->oob_buf;
+	int status, i, readcmd;
+
+	readcmd = ONENAND_IS_4KB_PAGE(this) ? ONENAND_CMD_READ : ONENAND_CMD_READOOB;
+
+	this->command(mtd, readcmd, to, mtd->oobsize);
+	onenand_update_bufferram(mtd, to, 0);
+	status = this->wait(mtd, FL_READING);
+	if (status)
+		return status;
+
+	this->read_bufferram(mtd, ONENAND_SPARERAM, oob_buf, 0, mtd->oobsize);
+	for (i = 0; i < mtd->oobsize; i++)
+		if (buf[i] != 0xFF && buf[i] != oob_buf[i])
+			return -EBADMSG;
+
+	return 0;
+}
+
+/**
+ * onenand_verify - [GENERIC] verify the chip contents after a write
+ * @param mtd          MTD device structure
+ * @param buf          the databuffer to verify
+ * @param addr         offset to read from
+ * @param len          number of bytes to read and compare
+ */
+static int onenand_verify(struct mtd_info *mtd, const u_char *buf, loff_t addr, size_t len)
+{
+	struct onenand_chip *this = mtd->priv;
+	int ret = 0;
+	int thislen, column;
+
+	column = addr & (this->writesize - 1);
+
+	while (len != 0) {
+		thislen = min_t(int, this->writesize - column, len);
+
+		this->command(mtd, ONENAND_CMD_READ, addr, this->writesize);
+
+		onenand_update_bufferram(mtd, addr, 0);
+
+		ret = this->wait(mtd, FL_READING);
+		if (ret)
+			return ret;
+
+		onenand_update_bufferram(mtd, addr, 1);
+
+		this->read_bufferram(mtd, ONENAND_DATARAM, this->verify_buf, 0, mtd->writesize);
+
+		if (memcmp(buf, this->verify_buf + column, thislen))
+			return -EBADMSG;
+
+		len -= thislen;
+		buf += thislen;
+		addr += thislen;
+		column = 0;
+	}
+
+	return 0;
+}
+#else
+#define onenand_verify(...)		(0)
+#define onenand_verify_oob(...)		(0)
+#endif
+
+#define NOTALIGNED(x)	((x & (this->subpagesize - 1)) != 0)
+
+static void onenand_panic_wait(struct mtd_info *mtd)
+{
+	struct onenand_chip *this = mtd->priv;
+	unsigned int interrupt;
+	int i;
+	
+	for (i = 0; i < 2000; i++) {
+		interrupt = this->read_word(this->base + ONENAND_REG_INTERRUPT);
+		if (interrupt & ONENAND_INT_MASTER)
+			break;
+		udelay(10);
+	}
+}
+
+/**
+ * onenand_panic_write - [MTD Interface] write buffer to FLASH in a panic context
+ * @param mtd		MTD device structure
+ * @param to		offset to write to
+ * @param len		number of bytes to write
+ * @param retlen	pointer to variable to store the number of written bytes
+ * @param buf		the data to write
+ *
+ * Write with ECC
+ */
+static int onenand_panic_write(struct mtd_info *mtd, loff_t to, size_t len,
+			 size_t *retlen, const u_char *buf)
+{
+	struct onenand_chip *this = mtd->priv;
+	int column, subpage;
+	int written = 0;
+
+	if (this->state == FL_PM_SUSPENDED)
+		return -EBUSY;
+
+	/* Wait for any existing operation to clear */
+	onenand_panic_wait(mtd);
+
+	pr_debug("%s: to = 0x%08x, len = %i\n", __func__, (unsigned int)to,
+			(int)len);
+
+	/* Reject writes, which are not page aligned */
+        if (unlikely(NOTALIGNED(to) || NOTALIGNED(len))) {
+		printk(KERN_ERR "%s: Attempt to write not page aligned data\n",
+			__func__);
+                return -EINVAL;
+        }
+
+	column = to & (mtd->writesize - 1);
+
+	/* Loop until all data write */
+	while (written < len) {
+		int thislen = min_t(int, mtd->writesize - column, len - written);
+		u_char *wbuf = (u_char *) buf;
+
+		this->command(mtd, ONENAND_CMD_BUFFERRAM, to, thislen);
+
+		/* Partial page write */
+		subpage = thislen < mtd->writesize;
+		if (subpage) {
+			memset(this->page_buf, 0xff, mtd->writesize);
+			memcpy(this->page_buf + column, buf, thislen);
+			wbuf = this->page_buf;
+		}
+
+		this->write_bufferram(mtd, ONENAND_DATARAM, wbuf, 0, mtd->writesize);
+		this->write_bufferram(mtd, ONENAND_SPARERAM, ffchars, 0, mtd->oobsize);
+
+		this->command(mtd, ONENAND_CMD_PROG, to, mtd->writesize);
+
+		onenand_panic_wait(mtd);
+
+		/* In partial page write we don't update bufferram */
+		onenand_update_bufferram(mtd, to, !subpage);
+		if (ONENAND_IS_2PLANE(this)) {
+			ONENAND_SET_BUFFERRAM1(this);
+			onenand_update_bufferram(mtd, to + this->writesize, !subpage);
+		}
+
+		written += thislen;
+
+		if (written == len)
+			break;
+
+		column = 0;
+		to += thislen;
+		buf += thislen;
+	}
+
+	*retlen = written;
+	return 0;
+}
+
+/**
+ * onenand_fill_auto_oob - [INTERN] oob auto-placement transfer
+ * @param mtd		MTD device structure
+ * @param oob_buf	oob buffer
+ * @param buf		source address
+ * @param column	oob offset to write to
+ * @param thislen	oob length to write
+ */
+static int onenand_fill_auto_oob(struct mtd_info *mtd, u_char *oob_buf,
+				  const u_char *buf, int column, int thislen)
+{
+	return mtd_ooblayout_set_databytes(mtd, buf, oob_buf, column, thislen);
+}
+
+/**
+ * onenand_write_ops_nolock - [OneNAND Interface] write main and/or out-of-band
+ * @param mtd		MTD device structure
+ * @param to		offset to write to
+ * @param ops		oob operation description structure
+ *
+ * Write main and/or oob with ECC
+ */
+static int onenand_write_ops_nolock(struct mtd_info *mtd, loff_t to,
+				struct mtd_oob_ops *ops)
+{
+	struct onenand_chip *this = mtd->priv;
+	int written = 0, column, thislen = 0, subpage = 0;
+	int prev = 0, prevlen = 0, prev_subpage = 0, first = 1;
+	int oobwritten = 0, oobcolumn, thisooblen, oobsize;
+	size_t len = ops->len;
+	size_t ooblen = ops->ooblen;
+	const u_char *buf = ops->datbuf;
+	const u_char *oob = ops->oobbuf;
+	u_char *oobbuf;
+	int ret = 0, cmd;
+
+	pr_debug("%s: to = 0x%08x, len = %i\n", __func__, (unsigned int)to,
+			(int)len);
+
+	/* Initialize retlen, in case of early exit */
+	ops->retlen = 0;
+	ops->oobretlen = 0;
+
+	/* Reject writes, which are not page aligned */
+        if (unlikely(NOTALIGNED(to) || NOTALIGNED(len))) {
+		printk(KERN_ERR "%s: Attempt to write not page aligned data\n",
+			__func__);
+                return -EINVAL;
+        }
+
+	/* Check zero length */
+	if (!len)
+		return 0;
+	oobsize = mtd_oobavail(mtd, ops);
+	oobcolumn = to & (mtd->oobsize - 1);
+
+	column = to & (mtd->writesize - 1);
+
+	/* Loop until all data write */
+	while (1) {
+		if (written < len) {
+			u_char *wbuf = (u_char *) buf;
+
+			thislen = min_t(int, mtd->writesize - column, len - written);
+			thisooblen = min_t(int, oobsize - oobcolumn, ooblen - oobwritten);
+
+			cond_resched();
+
+			this->command(mtd, ONENAND_CMD_BUFFERRAM, to, thislen);
+
+			/* Partial page write */
+			subpage = thislen < mtd->writesize;
+			if (subpage) {
+				memset(this->page_buf, 0xff, mtd->writesize);
+				memcpy(this->page_buf + column, buf, thislen);
+				wbuf = this->page_buf;
+			}
+
+			this->write_bufferram(mtd, ONENAND_DATARAM, wbuf, 0, mtd->writesize);
+
+			if (oob) {
+				oobbuf = this->oob_buf;
+
+				/* We send data to spare ram with oobsize
+				 * to prevent byte access */
+				memset(oobbuf, 0xff, mtd->oobsize);
+				if (ops->mode == MTD_OPS_AUTO_OOB)
+					onenand_fill_auto_oob(mtd, oobbuf, oob, oobcolumn, thisooblen);
+				else
+					memcpy(oobbuf + oobcolumn, oob, thisooblen);
+
+				oobwritten += thisooblen;
+				oob += thisooblen;
+				oobcolumn = 0;
+			} else
+				oobbuf = (u_char *) ffchars;
+
+			this->write_bufferram(mtd, ONENAND_SPARERAM, oobbuf, 0, mtd->oobsize);
+		} else
+			ONENAND_SET_NEXT_BUFFERRAM(this);
+
+		/*
+		 * 2 PLANE, MLC, and Flex-OneNAND do not support
+		 * write-while-program feature.
+		 */
+		if (!ONENAND_IS_2PLANE(this) && !ONENAND_IS_4KB_PAGE(this) && !first) {
+			ONENAND_SET_PREV_BUFFERRAM(this);
+
+			ret = this->wait(mtd, FL_WRITING);
+
+			/* In partial page write we don't update bufferram */
+			onenand_update_bufferram(mtd, prev, !ret && !prev_subpage);
+			if (ret) {
+				written -= prevlen;
+				printk(KERN_ERR "%s: write failed %d\n",
+					__func__, ret);
+				break;
+			}
+
+			if (written == len) {
+				/* Only check verify write turn on */
+				ret = onenand_verify(mtd, buf - len, to - len, len);
+				if (ret)
+					printk(KERN_ERR "%s: verify failed %d\n",
+						__func__, ret);
+				break;
+			}
+
+			ONENAND_SET_NEXT_BUFFERRAM(this);
+		}
+
+		this->ongoing = 0;
+		cmd = ONENAND_CMD_PROG;
+
+		/* Exclude 1st OTP and OTP blocks for cache program feature */
+		if (ONENAND_IS_CACHE_PROGRAM(this) &&
+		    likely(onenand_block(this, to) != 0) &&
+		    ONENAND_IS_4KB_PAGE(this) &&
+		    ((written + thislen) < len)) {
+			cmd = ONENAND_CMD_2X_CACHE_PROG;
+			this->ongoing = 1;
+		}
+
+		this->command(mtd, cmd, to, mtd->writesize);
+
+		/*
+		 * 2 PLANE, MLC, and Flex-OneNAND wait here
+		 */
+		if (ONENAND_IS_2PLANE(this) || ONENAND_IS_4KB_PAGE(this)) {
+			ret = this->wait(mtd, FL_WRITING);
+
+			/* In partial page write we don't update bufferram */
+			onenand_update_bufferram(mtd, to, !ret && !subpage);
+			if (ret) {
+				printk(KERN_ERR "%s: write failed %d\n",
+					__func__, ret);
+				break;
+			}
+
+			/* Only check verify write turn on */
+			ret = onenand_verify(mtd, buf, to, thislen);
+			if (ret) {
+				printk(KERN_ERR "%s: verify failed %d\n",
+					__func__, ret);
+				break;
+			}
+
+			written += thislen;
+
+			if (written == len)
+				break;
+
+		} else
+			written += thislen;
+
+		column = 0;
+		prev_subpage = subpage;
+		prev = to;
+		prevlen = thislen;
+		to += thislen;
+		buf += thislen;
+		first = 0;
+	}
+
+	/* In error case, clear all bufferrams */
+	if (written != len)
+		onenand_invalidate_bufferram(mtd, 0, -1);
+
+	ops->retlen = written;
+	ops->oobretlen = oobwritten;
+
+	return ret;
+}
+
+
+/**
+ * onenand_write_oob_nolock - [INTERN] OneNAND write out-of-band
+ * @param mtd		MTD device structure
+ * @param to		offset to write to
+ * @param len		number of bytes to write
+ * @param retlen	pointer to variable to store the number of written bytes
+ * @param buf		the data to write
+ * @param mode		operation mode
+ *
+ * OneNAND write out-of-band
+ */
+static int onenand_write_oob_nolock(struct mtd_info *mtd, loff_t to,
+				    struct mtd_oob_ops *ops)
+{
+	struct onenand_chip *this = mtd->priv;
+	int column, ret = 0, oobsize;
+	int written = 0, oobcmd;
+	u_char *oobbuf;
+	size_t len = ops->ooblen;
+	const u_char *buf = ops->oobbuf;
+	unsigned int mode = ops->mode;
+
+	to += ops->ooboffs;
+
+	pr_debug("%s: to = 0x%08x, len = %i\n", __func__, (unsigned int)to,
+			(int)len);
+
+	/* Initialize retlen, in case of early exit */
+	ops->oobretlen = 0;
+
+	if (mode == MTD_OPS_AUTO_OOB)
+		oobsize = mtd->oobavail;
+	else
+		oobsize = mtd->oobsize;
+
+	column = to & (mtd->oobsize - 1);
+
+	if (unlikely(column >= oobsize)) {
+		printk(KERN_ERR "%s: Attempted to start write outside oob\n",
+			__func__);
+		return -EINVAL;
+	}
+
+	/* For compatibility with NAND: Do not allow write past end of page */
+	if (unlikely(column + len > oobsize)) {
+		printk(KERN_ERR "%s: Attempt to write past end of page\n",
+			__func__);
+		return -EINVAL;
+	}
+
+	oobbuf = this->oob_buf;
+
+	oobcmd = ONENAND_IS_4KB_PAGE(this) ? ONENAND_CMD_PROG : ONENAND_CMD_PROGOOB;
+
+	/* Loop until all data write */
+	while (written < len) {
+		int thislen = min_t(int, oobsize, len - written);
+
+		cond_resched();
+
+		this->command(mtd, ONENAND_CMD_BUFFERRAM, to, mtd->oobsize);
+
+		/* We send data to spare ram with oobsize
+		 * to prevent byte access */
+		memset(oobbuf, 0xff, mtd->oobsize);
+		if (mode == MTD_OPS_AUTO_OOB)
+			onenand_fill_auto_oob(mtd, oobbuf, buf, column, thislen);
+		else
+			memcpy(oobbuf + column, buf, thislen);
+		this->write_bufferram(mtd, ONENAND_SPARERAM, oobbuf, 0, mtd->oobsize);
+
+		if (ONENAND_IS_4KB_PAGE(this)) {
+			/* Set main area of DataRAM to 0xff*/
+			memset(this->page_buf, 0xff, mtd->writesize);
+			this->write_bufferram(mtd, ONENAND_DATARAM,
+					 this->page_buf, 0, mtd->writesize);
+		}
+
+		this->command(mtd, oobcmd, to, mtd->oobsize);
+
+		onenand_update_bufferram(mtd, to, 0);
+		if (ONENAND_IS_2PLANE(this)) {
+			ONENAND_SET_BUFFERRAM1(this);
+			onenand_update_bufferram(mtd, to + this->writesize, 0);
+		}
+
+		ret = this->wait(mtd, FL_WRITING);
+		if (ret) {
+			printk(KERN_ERR "%s: write failed %d\n", __func__, ret);
+			break;
+		}
+
+		ret = onenand_verify_oob(mtd, oobbuf, to);
+		if (ret) {
+			printk(KERN_ERR "%s: verify failed %d\n",
+				__func__, ret);
+			break;
+		}
+
+		written += thislen;
+		if (written == len)
+			break;
+
+		to += mtd->writesize;
+		buf += thislen;
+		column = 0;
+	}
+
+	ops->oobretlen = written;
+
+	return ret;
+}
+
+/**
+ * onenand_write_oob - [MTD Interface] NAND write data and/or out-of-band
+ * @param mtd:		MTD device structure
+ * @param to:		offset to write
+ * @param ops:		oob operation description structure
+ */
+static int onenand_write_oob(struct mtd_info *mtd, loff_t to,
+			     struct mtd_oob_ops *ops)
+{
+	int ret;
+
+	switch (ops->mode) {
+	case MTD_OPS_PLACE_OOB:
+	case MTD_OPS_AUTO_OOB:
+		break;
+	case MTD_OPS_RAW:
+		/* Not implemented yet */
+	default:
+		return -EINVAL;
+	}
+
+	onenand_get_device(mtd, FL_WRITING);
+	if (ops->datbuf)
+		ret = onenand_write_ops_nolock(mtd, to, ops);
+	else
+		ret = onenand_write_oob_nolock(mtd, to, ops);
+	onenand_release_device(mtd);
+
+	return ret;
+}
+
+/**
+ * onenand_block_isbad_nolock - [GENERIC] Check if a block is marked bad
+ * @param mtd		MTD device structure
+ * @param ofs		offset from device start
+ * @param allowbbt	1, if its allowed to access the bbt area
+ *
+ * Check, if the block is bad. Either by reading the bad block table or
+ * calling of the scan function.
+ */
+static int onenand_block_isbad_nolock(struct mtd_info *mtd, loff_t ofs, int allowbbt)
+{
+	struct onenand_chip *this = mtd->priv;
+	struct bbm_info *bbm = this->bbm;
+
+	/* Return info from the table */
+	return bbm->isbad_bbt(mtd, ofs, allowbbt);
+}
+
+
+static int onenand_multiblock_erase_verify(struct mtd_info *mtd,
+					   struct erase_info *instr)
+{
+	struct onenand_chip *this = mtd->priv;
+	loff_t addr = instr->addr;
+	int len = instr->len;
+	unsigned int block_size = (1 << this->erase_shift);
+	int ret = 0;
+
+	while (len) {
+		this->command(mtd, ONENAND_CMD_ERASE_VERIFY, addr, block_size);
+		ret = this->wait(mtd, FL_VERIFYING_ERASE);
+		if (ret) {
+			printk(KERN_ERR "%s: Failed verify, block %d\n",
+			       __func__, onenand_block(this, addr));
+			instr->fail_addr = addr;
+			return -1;
+		}
+		len -= block_size;
+		addr += block_size;
+	}
+	return 0;
+}
+
+/**
+ * onenand_multiblock_erase - [INTERN] erase block(s) using multiblock erase
+ * @param mtd		MTD device structure
+ * @param instr		erase instruction
+ * @param region	erase region
+ *
+ * Erase one or more blocks up to 64 block at a time
+ */
+static int onenand_multiblock_erase(struct mtd_info *mtd,
+				    struct erase_info *instr,
+				    unsigned int block_size)
+{
+	struct onenand_chip *this = mtd->priv;
+	loff_t addr = instr->addr;
+	int len = instr->len;
+	int eb_count = 0;
+	int ret = 0;
+	int bdry_block = 0;
+
+	if (ONENAND_IS_DDP(this)) {
+		loff_t bdry_addr = this->chipsize >> 1;
+		if (addr < bdry_addr && (addr + len) > bdry_addr)
+			bdry_block = bdry_addr >> this->erase_shift;
+	}
+
+	/* Pre-check bbs */
+	while (len) {
+		/* Check if we have a bad block, we do not erase bad blocks */
+		if (onenand_block_isbad_nolock(mtd, addr, 0)) {
+			printk(KERN_WARNING "%s: attempt to erase a bad block "
+			       "at addr 0x%012llx\n",
+			       __func__, (unsigned long long) addr);
+			return -EIO;
+		}
+		len -= block_size;
+		addr += block_size;
+	}
+
+	len = instr->len;
+	addr = instr->addr;
+
+	/* loop over 64 eb batches */
+	while (len) {
+		struct erase_info verify_instr = *instr;
+		int max_eb_count = MB_ERASE_MAX_BLK_COUNT;
+
+		verify_instr.addr = addr;
+		verify_instr.len = 0;
+
+		/* do not cross chip boundary */
+		if (bdry_block) {
+			int this_block = (addr >> this->erase_shift);
+
+			if (this_block < bdry_block) {
+				max_eb_count = min(max_eb_count,
+						   (bdry_block - this_block));
+			}
+		}
+
+		eb_count = 0;
+
+		while (len > block_size && eb_count < (max_eb_count - 1)) {
+			this->command(mtd, ONENAND_CMD_MULTIBLOCK_ERASE,
+				      addr, block_size);
+			onenand_invalidate_bufferram(mtd, addr, block_size);
+
+			ret = this->wait(mtd, FL_PREPARING_ERASE);
+			if (ret) {
+				printk(KERN_ERR "%s: Failed multiblock erase, "
+				       "block %d\n", __func__,
+				       onenand_block(this, addr));
+				instr->fail_addr = MTD_FAIL_ADDR_UNKNOWN;
+				return -EIO;
+			}
+
+			len -= block_size;
+			addr += block_size;
+			eb_count++;
+		}
+
+		/* last block of 64-eb series */
+		cond_resched();
+		this->command(mtd, ONENAND_CMD_ERASE, addr, block_size);
+		onenand_invalidate_bufferram(mtd, addr, block_size);
+
+		ret = this->wait(mtd, FL_ERASING);
+		/* Check if it is write protected */
+		if (ret) {
+			printk(KERN_ERR "%s: Failed erase, block %d\n",
+			       __func__, onenand_block(this, addr));
+			instr->fail_addr = MTD_FAIL_ADDR_UNKNOWN;
+			return -EIO;
+		}
+
+		len -= block_size;
+		addr += block_size;
+		eb_count++;
+
+		/* verify */
+		verify_instr.len = eb_count * block_size;
+		if (onenand_multiblock_erase_verify(mtd, &verify_instr)) {
+			instr->fail_addr = verify_instr.fail_addr;
+			return -EIO;
+		}
+
+	}
+	return 0;
+}
+
+
+/**
+ * onenand_block_by_block_erase - [INTERN] erase block(s) using regular erase
+ * @param mtd		MTD device structure
+ * @param instr		erase instruction
+ * @param region	erase region
+ * @param block_size	erase block size
+ *
+ * Erase one or more blocks one block at a time
+ */
+static int onenand_block_by_block_erase(struct mtd_info *mtd,
+					struct erase_info *instr,
+					struct mtd_erase_region_info *region,
+					unsigned int block_size)
+{
+	struct onenand_chip *this = mtd->priv;
+	loff_t addr = instr->addr;
+	int len = instr->len;
+	loff_t region_end = 0;
+	int ret = 0;
+
+	if (region) {
+		/* region is set for Flex-OneNAND */
+		region_end = region->offset + region->erasesize * region->numblocks;
+	}
+
+	/* Loop through the blocks */
+	while (len) {
+		cond_resched();
+
+		/* Check if we have a bad block, we do not erase bad blocks */
+		if (onenand_block_isbad_nolock(mtd, addr, 0)) {
+			printk(KERN_WARNING "%s: attempt to erase a bad block "
+					"at addr 0x%012llx\n",
+					__func__, (unsigned long long) addr);
+			return -EIO;
+		}
+
+		this->command(mtd, ONENAND_CMD_ERASE, addr, block_size);
+
+		onenand_invalidate_bufferram(mtd, addr, block_size);
+
+		ret = this->wait(mtd, FL_ERASING);
+		/* Check, if it is write protected */
+		if (ret) {
+			printk(KERN_ERR "%s: Failed erase, block %d\n",
+				__func__, onenand_block(this, addr));
+			instr->fail_addr = addr;
+			return -EIO;
+		}
+
+		len -= block_size;
+		addr += block_size;
+
+		if (region && addr == region_end) {
+			if (!len)
+				break;
+			region++;
+
+			block_size = region->erasesize;
+			region_end = region->offset + region->erasesize * region->numblocks;
+
+			if (len & (block_size - 1)) {
+				/* FIXME: This should be handled at MTD partitioning level. */
+				printk(KERN_ERR "%s: Unaligned address\n",
+					__func__);
+				return -EIO;
+			}
+		}
+	}
+	return 0;
+}
+
+/**
+ * onenand_erase - [MTD Interface] erase block(s)
+ * @param mtd		MTD device structure
+ * @param instr		erase instruction
+ *
+ * Erase one or more blocks
+ */
+static int onenand_erase(struct mtd_info *mtd, struct erase_info *instr)
+{
+	struct onenand_chip *this = mtd->priv;
+	unsigned int block_size;
+	loff_t addr = instr->addr;
+	loff_t len = instr->len;
+	int ret = 0;
+	struct mtd_erase_region_info *region = NULL;
+	loff_t region_offset = 0;
+
+	pr_debug("%s: start=0x%012llx, len=%llu\n", __func__,
+			(unsigned long long)instr->addr,
+			(unsigned long long)instr->len);
+
+	if (FLEXONENAND(this)) {
+		/* Find the eraseregion of this address */
+		int i = flexonenand_region(mtd, addr);
+
+		region = &mtd->eraseregions[i];
+		block_size = region->erasesize;
+
+		/* Start address within region must align on block boundary.
+		 * Erase region's start offset is always block start address.
+		 */
+		region_offset = region->offset;
+	} else
+		block_size = 1 << this->erase_shift;
+
+	/* Start address must align on block boundary */
+	if (unlikely((addr - region_offset) & (block_size - 1))) {
+		printk(KERN_ERR "%s: Unaligned address\n", __func__);
+		return -EINVAL;
+	}
+
+	/* Length must align on block boundary */
+	if (unlikely(len & (block_size - 1))) {
+		printk(KERN_ERR "%s: Length not block aligned\n", __func__);
+		return -EINVAL;
+	}
+
+	/* Grab the lock and see if the device is available */
+	onenand_get_device(mtd, FL_ERASING);
+
+	if (ONENAND_IS_4KB_PAGE(this) || region ||
+	    instr->len < MB_ERASE_MIN_BLK_COUNT * block_size) {
+		/* region is set for Flex-OneNAND (no mb erase) */
+		ret = onenand_block_by_block_erase(mtd, instr,
+						   region, block_size);
+	} else {
+		ret = onenand_multiblock_erase(mtd, instr, block_size);
+	}
+
+	/* Deselect and wake up anyone waiting on the device */
+	onenand_release_device(mtd);
+
+	return ret;
+}
+
+/**
+ * onenand_sync - [MTD Interface] sync
+ * @param mtd		MTD device structure
+ *
+ * Sync is actually a wait for chip ready function
+ */
+static void onenand_sync(struct mtd_info *mtd)
+{
+	pr_debug("%s: called\n", __func__);
+
+	/* Grab the lock and see if the device is available */
+	onenand_get_device(mtd, FL_SYNCING);
+
+	/* Release it and go back */
+	onenand_release_device(mtd);
+}
+
+/**
+ * onenand_block_isbad - [MTD Interface] Check whether the block at the given offset is bad
+ * @param mtd		MTD device structure
+ * @param ofs		offset relative to mtd start
+ *
+ * Check whether the block is bad
+ */
+static int onenand_block_isbad(struct mtd_info *mtd, loff_t ofs)
+{
+	int ret;
+
+	onenand_get_device(mtd, FL_READING);
+	ret = onenand_block_isbad_nolock(mtd, ofs, 0);
+	onenand_release_device(mtd);
+	return ret;
+}
+
+/**
+ * onenand_default_block_markbad - [DEFAULT] mark a block bad
+ * @param mtd		MTD device structure
+ * @param ofs		offset from device start
+ *
+ * This is the default implementation, which can be overridden by
+ * a hardware specific driver.
+ */
+static int onenand_default_block_markbad(struct mtd_info *mtd, loff_t ofs)
+{
+	struct onenand_chip *this = mtd->priv;
+	struct bbm_info *bbm = this->bbm;
+	u_char buf[2] = {0, 0};
+	struct mtd_oob_ops ops = {
+		.mode = MTD_OPS_PLACE_OOB,
+		.ooblen = 2,
+		.oobbuf = buf,
+		.ooboffs = 0,
+	};
+	int block;
+
+	/* Get block number */
+	block = onenand_block(this, ofs);
+        if (bbm->bbt)
+                bbm->bbt[block >> 2] |= 0x01 << ((block & 0x03) << 1);
+
+        /* We write two bytes, so we don't have to mess with 16-bit access */
+        ofs += mtd->oobsize + (bbm->badblockpos & ~0x01);
+	/* FIXME : What to do when marking SLC block in partition
+	 * 	   with MLC erasesize? For now, it is not advisable to
+	 *	   create partitions containing both SLC and MLC regions.
+	 */
+	return onenand_write_oob_nolock(mtd, ofs, &ops);
+}
+
+/**
+ * onenand_block_markbad - [MTD Interface] Mark the block at the given offset as bad
+ * @param mtd		MTD device structure
+ * @param ofs		offset relative to mtd start
+ *
+ * Mark the block as bad
+ */
+static int onenand_block_markbad(struct mtd_info *mtd, loff_t ofs)
+{
+	struct onenand_chip *this = mtd->priv;
+	int ret;
+
+	ret = onenand_block_isbad(mtd, ofs);
+	if (ret) {
+		/* If it was bad already, return success and do nothing */
+		if (ret > 0)
+			return 0;
+		return ret;
+	}
+
+	onenand_get_device(mtd, FL_WRITING);
+	ret = this->block_markbad(mtd, ofs);
+	onenand_release_device(mtd);
+	return ret;
+}
+
+/**
+ * onenand_do_lock_cmd - [OneNAND Interface] Lock or unlock block(s)
+ * @param mtd		MTD device structure
+ * @param ofs		offset relative to mtd start
+ * @param len		number of bytes to lock or unlock
+ * @param cmd		lock or unlock command
+ *
+ * Lock or unlock one or more blocks
+ */
+static int onenand_do_lock_cmd(struct mtd_info *mtd, loff_t ofs, size_t len, int cmd)
+{
+	struct onenand_chip *this = mtd->priv;
+	int start, end, block, value, status;
+	int wp_status_mask;
+
+	start = onenand_block(this, ofs);
+	end = onenand_block(this, ofs + len) - 1;
+
+	if (cmd == ONENAND_CMD_LOCK)
+		wp_status_mask = ONENAND_WP_LS;
+	else
+		wp_status_mask = ONENAND_WP_US;
+
+	/* Continuous lock scheme */
+	if (this->options & ONENAND_HAS_CONT_LOCK) {
+		/* Set start block address */
+		this->write_word(start, this->base + ONENAND_REG_START_BLOCK_ADDRESS);
+		/* Set end block address */
+		this->write_word(end, this->base +  ONENAND_REG_END_BLOCK_ADDRESS);
+		/* Write lock command */
+		this->command(mtd, cmd, 0, 0);
+
+		/* There's no return value */
+		this->wait(mtd, FL_LOCKING);
+
+		/* Sanity check */
+		while (this->read_word(this->base + ONENAND_REG_CTRL_STATUS)
+		    & ONENAND_CTRL_ONGO)
+			continue;
+
+		/* Check lock status */
+		status = this->read_word(this->base + ONENAND_REG_WP_STATUS);
+		if (!(status & wp_status_mask))
+			printk(KERN_ERR "%s: wp status = 0x%x\n",
+				__func__, status);
+
+		return 0;
+	}
+
+	/* Block lock scheme */
+	for (block = start; block < end + 1; block++) {
+		/* Set block address */
+		value = onenand_block_address(this, block);
+		this->write_word(value, this->base + ONENAND_REG_START_ADDRESS1);
+		/* Select DataRAM for DDP */
+		value = onenand_bufferram_address(this, block);
+		this->write_word(value, this->base + ONENAND_REG_START_ADDRESS2);
+		/* Set start block address */
+		this->write_word(block, this->base + ONENAND_REG_START_BLOCK_ADDRESS);
+		/* Write lock command */
+		this->command(mtd, cmd, 0, 0);
+
+		/* There's no return value */
+		this->wait(mtd, FL_LOCKING);
+
+		/* Sanity check */
+		while (this->read_word(this->base + ONENAND_REG_CTRL_STATUS)
+		    & ONENAND_CTRL_ONGO)
+			continue;
+
+		/* Check lock status */
+		status = this->read_word(this->base + ONENAND_REG_WP_STATUS);
+		if (!(status & wp_status_mask))
+			printk(KERN_ERR "%s: block = %d, wp status = 0x%x\n",
+				__func__, block, status);
+	}
+
+	return 0;
+}
+
+/**
+ * onenand_lock - [MTD Interface] Lock block(s)
+ * @param mtd		MTD device structure
+ * @param ofs		offset relative to mtd start
+ * @param len		number of bytes to unlock
+ *
+ * Lock one or more blocks
+ */
+static int onenand_lock(struct mtd_info *mtd, loff_t ofs, uint64_t len)
+{
+	int ret;
+
+	onenand_get_device(mtd, FL_LOCKING);
+	ret = onenand_do_lock_cmd(mtd, ofs, len, ONENAND_CMD_LOCK);
+	onenand_release_device(mtd);
+	return ret;
+}
+
+/**
+ * onenand_unlock - [MTD Interface] Unlock block(s)
+ * @param mtd		MTD device structure
+ * @param ofs		offset relative to mtd start
+ * @param len		number of bytes to unlock
+ *
+ * Unlock one or more blocks
+ */
+static int onenand_unlock(struct mtd_info *mtd, loff_t ofs, uint64_t len)
+{
+	int ret;
+
+	onenand_get_device(mtd, FL_LOCKING);
+	ret = onenand_do_lock_cmd(mtd, ofs, len, ONENAND_CMD_UNLOCK);
+	onenand_release_device(mtd);
+	return ret;
+}
+
+/**
+ * onenand_check_lock_status - [OneNAND Interface] Check lock status
+ * @param this		onenand chip data structure
+ *
+ * Check lock status
+ */
+static int onenand_check_lock_status(struct onenand_chip *this)
+{
+	unsigned int value, block, status;
+	unsigned int end;
+
+	end = this->chipsize >> this->erase_shift;
+	for (block = 0; block < end; block++) {
+		/* Set block address */
+		value = onenand_block_address(this, block);
+		this->write_word(value, this->base + ONENAND_REG_START_ADDRESS1);
+		/* Select DataRAM for DDP */
+		value = onenand_bufferram_address(this, block);
+		this->write_word(value, this->base + ONENAND_REG_START_ADDRESS2);
+		/* Set start block address */
+		this->write_word(block, this->base + ONENAND_REG_START_BLOCK_ADDRESS);
+
+		/* Check lock status */
+		status = this->read_word(this->base + ONENAND_REG_WP_STATUS);
+		if (!(status & ONENAND_WP_US)) {
+			printk(KERN_ERR "%s: block = %d, wp status = 0x%x\n",
+				__func__, block, status);
+			return 0;
+		}
+	}
+
+	return 1;
+}
+
+/**
+ * onenand_unlock_all - [OneNAND Interface] unlock all blocks
+ * @param mtd		MTD device structure
+ *
+ * Unlock all blocks
+ */
+static void onenand_unlock_all(struct mtd_info *mtd)
+{
+	struct onenand_chip *this = mtd->priv;
+	loff_t ofs = 0;
+	loff_t len = mtd->size;
+
+	if (this->options & ONENAND_HAS_UNLOCK_ALL) {
+		/* Set start block address */
+		this->write_word(0, this->base + ONENAND_REG_START_BLOCK_ADDRESS);
+		/* Write unlock command */
+		this->command(mtd, ONENAND_CMD_UNLOCK_ALL, 0, 0);
+
+		/* There's no return value */
+		this->wait(mtd, FL_LOCKING);
+
+		/* Sanity check */
+		while (this->read_word(this->base + ONENAND_REG_CTRL_STATUS)
+		    & ONENAND_CTRL_ONGO)
+			continue;
+
+		/* Don't check lock status */
+		if (this->options & ONENAND_SKIP_UNLOCK_CHECK)
+			return;
+
+		/* Check lock status */
+		if (onenand_check_lock_status(this))
+			return;
+
+		/* Workaround for all block unlock in DDP */
+		if (ONENAND_IS_DDP(this) && !FLEXONENAND(this)) {
+			/* All blocks on another chip */
+			ofs = this->chipsize >> 1;
+			len = this->chipsize >> 1;
+		}
+	}
+
+	onenand_do_lock_cmd(mtd, ofs, len, ONENAND_CMD_UNLOCK);
+}
+
+#ifdef CONFIG_MTD_ONENAND_OTP
+
+/**
+ * onenand_otp_command - Send OTP specific command to OneNAND device
+ * @param mtd	 MTD device structure
+ * @param cmd	 the command to be sent
+ * @param addr	 offset to read from or write to
+ * @param len	 number of bytes to read or write
+ */
+static int onenand_otp_command(struct mtd_info *mtd, int cmd, loff_t addr,
+				size_t len)
+{
+	struct onenand_chip *this = mtd->priv;
+	int value, block, page;
+
+	/* Address translation */
+	switch (cmd) {
+	case ONENAND_CMD_OTP_ACCESS:
+		block = (int) (addr >> this->erase_shift);
+		page = -1;
+		break;
+
+	default:
+		block = (int) (addr >> this->erase_shift);
+		page = (int) (addr >> this->page_shift);
+
+		if (ONENAND_IS_2PLANE(this)) {
+			/* Make the even block number */
+			block &= ~1;
+			/* Is it the odd plane? */
+			if (addr & this->writesize)
+				block++;
+			page >>= 1;
+		}
+		page &= this->page_mask;
+		break;
+	}
+
+	if (block != -1) {
+		/* Write 'DFS, FBA' of Flash */
+		value = onenand_block_address(this, block);
+		this->write_word(value, this->base +
+				ONENAND_REG_START_ADDRESS1);
+	}
+
+	if (page != -1) {
+		/* Now we use page size operation */
+		int sectors = 4, count = 4;
+		int dataram;
+
+		switch (cmd) {
+		default:
+			if (ONENAND_IS_2PLANE(this) && cmd == ONENAND_CMD_PROG)
+				cmd = ONENAND_CMD_2X_PROG;
+			dataram = ONENAND_CURRENT_BUFFERRAM(this);
+			break;
+		}
+
+		/* Write 'FPA, FSA' of Flash */
+		value = onenand_page_address(page, sectors);
+		this->write_word(value, this->base +
+				ONENAND_REG_START_ADDRESS8);
+
+		/* Write 'BSA, BSC' of DataRAM */
+		value = onenand_buffer_address(dataram, sectors, count);
+		this->write_word(value, this->base + ONENAND_REG_START_BUFFER);
+	}
+
+	/* Interrupt clear */
+	this->write_word(ONENAND_INT_CLEAR, this->base + ONENAND_REG_INTERRUPT);
+
+	/* Write command */
+	this->write_word(cmd, this->base + ONENAND_REG_COMMAND);
+
+	return 0;
+}
+
+/**
+ * onenand_otp_write_oob_nolock - [INTERN] OneNAND write out-of-band, specific to OTP
+ * @param mtd		MTD device structure
+ * @param to		offset to write to
+ * @param len		number of bytes to write
+ * @param retlen	pointer to variable to store the number of written bytes
+ * @param buf		the data to write
+ *
+ * OneNAND write out-of-band only for OTP
+ */
+static int onenand_otp_write_oob_nolock(struct mtd_info *mtd, loff_t to,
+				    struct mtd_oob_ops *ops)
+{
+	struct onenand_chip *this = mtd->priv;
+	int column, ret = 0, oobsize;
+	int written = 0;
+	u_char *oobbuf;
+	size_t len = ops->ooblen;
+	const u_char *buf = ops->oobbuf;
+	int block, value, status;
+
+	to += ops->ooboffs;
+
+	/* Initialize retlen, in case of early exit */
+	ops->oobretlen = 0;
+
+	oobsize = mtd->oobsize;
+
+	column = to & (mtd->oobsize - 1);
+
+	oobbuf = this->oob_buf;
+
+	/* Loop until all data write */
+	while (written < len) {
+		int thislen = min_t(int, oobsize, len - written);
+
+		cond_resched();
+
+		block = (int) (to >> this->erase_shift);
+		/*
+		 * Write 'DFS, FBA' of Flash
+		 * Add: F100h DQ=DFS, FBA
+		 */
+
+		value = onenand_block_address(this, block);
+		this->write_word(value, this->base +
+				ONENAND_REG_START_ADDRESS1);
+
+		/*
+		 * Select DataRAM for DDP
+		 * Add: F101h DQ=DBS
+		 */
+
+		value = onenand_bufferram_address(this, block);
+		this->write_word(value, this->base +
+				ONENAND_REG_START_ADDRESS2);
+		ONENAND_SET_NEXT_BUFFERRAM(this);
+
+		/*
+		 * Enter OTP access mode
+		 */
+		this->command(mtd, ONENAND_CMD_OTP_ACCESS, 0, 0);
+		this->wait(mtd, FL_OTPING);
+
+		/* We send data to spare ram with oobsize
+		 * to prevent byte access */
+		memcpy(oobbuf + column, buf, thislen);
+
+		/*
+		 * Write Data into DataRAM
+		 * Add: 8th Word
+		 * in sector0/spare/page0
+		 * DQ=XXFCh
+		 */
+		this->write_bufferram(mtd, ONENAND_SPARERAM,
+					oobbuf, 0, mtd->oobsize);
+
+		onenand_otp_command(mtd, ONENAND_CMD_PROGOOB, to, mtd->oobsize);
+		onenand_update_bufferram(mtd, to, 0);
+		if (ONENAND_IS_2PLANE(this)) {
+			ONENAND_SET_BUFFERRAM1(this);
+			onenand_update_bufferram(mtd, to + this->writesize, 0);
+		}
+
+		ret = this->wait(mtd, FL_WRITING);
+		if (ret) {
+			printk(KERN_ERR "%s: write failed %d\n", __func__, ret);
+			break;
+		}
+
+		/* Exit OTP access mode */
+		this->command(mtd, ONENAND_CMD_RESET, 0, 0);
+		this->wait(mtd, FL_RESETING);
+
+		status = this->read_word(this->base + ONENAND_REG_CTRL_STATUS);
+		status &= 0x60;
+
+		if (status == 0x60) {
+			printk(KERN_DEBUG "\nBLOCK\tSTATUS\n");
+			printk(KERN_DEBUG "1st Block\tLOCKED\n");
+			printk(KERN_DEBUG "OTP Block\tLOCKED\n");
+		} else if (status == 0x20) {
+			printk(KERN_DEBUG "\nBLOCK\tSTATUS\n");
+			printk(KERN_DEBUG "1st Block\tLOCKED\n");
+			printk(KERN_DEBUG "OTP Block\tUN-LOCKED\n");
+		} else if (status == 0x40) {
+			printk(KERN_DEBUG "\nBLOCK\tSTATUS\n");
+			printk(KERN_DEBUG "1st Block\tUN-LOCKED\n");
+			printk(KERN_DEBUG "OTP Block\tLOCKED\n");
+		} else {
+			printk(KERN_DEBUG "Reboot to check\n");
+		}
+
+		written += thislen;
+		if (written == len)
+			break;
+
+		to += mtd->writesize;
+		buf += thislen;
+		column = 0;
+	}
+
+	ops->oobretlen = written;
+
+	return ret;
+}
+
+/* Internal OTP operation */
+typedef int (*otp_op_t)(struct mtd_info *mtd, loff_t form, size_t len,
+		size_t *retlen, u_char *buf);
+
+/**
+ * do_otp_read - [DEFAULT] Read OTP block area
+ * @param mtd		MTD device structure
+ * @param from		The offset to read
+ * @param len		number of bytes to read
+ * @param retlen	pointer to variable to store the number of readbytes
+ * @param buf		the databuffer to put/get data
+ *
+ * Read OTP block area.
+ */
+static int do_otp_read(struct mtd_info *mtd, loff_t from, size_t len,
+		size_t *retlen, u_char *buf)
+{
+	struct onenand_chip *this = mtd->priv;
+	struct mtd_oob_ops ops = {
+		.len	= len,
+		.ooblen	= 0,
+		.datbuf	= buf,
+		.oobbuf	= NULL,
+	};
+	int ret;
+
+	/* Enter OTP access mode */
+	this->command(mtd, ONENAND_CMD_OTP_ACCESS, 0, 0);
+	this->wait(mtd, FL_OTPING);
+
+	ret = ONENAND_IS_4KB_PAGE(this) ?
+		onenand_mlc_read_ops_nolock(mtd, from, &ops) :
+		onenand_read_ops_nolock(mtd, from, &ops);
+
+	/* Exit OTP access mode */
+	this->command(mtd, ONENAND_CMD_RESET, 0, 0);
+	this->wait(mtd, FL_RESETING);
+
+	return ret;
+}
+
+/**
+ * do_otp_write - [DEFAULT] Write OTP block area
+ * @param mtd		MTD device structure
+ * @param to		The offset to write
+ * @param len		number of bytes to write
+ * @param retlen	pointer to variable to store the number of write bytes
+ * @param buf		the databuffer to put/get data
+ *
+ * Write OTP block area.
+ */
+static int do_otp_write(struct mtd_info *mtd, loff_t to, size_t len,
+		size_t *retlen, u_char *buf)
+{
+	struct onenand_chip *this = mtd->priv;
+	unsigned char *pbuf = buf;
+	int ret;
+	struct mtd_oob_ops ops;
+
+	/* Force buffer page aligned */
+	if (len < mtd->writesize) {
+		memcpy(this->page_buf, buf, len);
+		memset(this->page_buf + len, 0xff, mtd->writesize - len);
+		pbuf = this->page_buf;
+		len = mtd->writesize;
+	}
+
+	/* Enter OTP access mode */
+	this->command(mtd, ONENAND_CMD_OTP_ACCESS, 0, 0);
+	this->wait(mtd, FL_OTPING);
+
+	ops.len = len;
+	ops.ooblen = 0;
+	ops.datbuf = pbuf;
+	ops.oobbuf = NULL;
+	ret = onenand_write_ops_nolock(mtd, to, &ops);
+	*retlen = ops.retlen;
+
+	/* Exit OTP access mode */
+	this->command(mtd, ONENAND_CMD_RESET, 0, 0);
+	this->wait(mtd, FL_RESETING);
+
+	return ret;
+}
+
+/**
+ * do_otp_lock - [DEFAULT] Lock OTP block area
+ * @param mtd		MTD device structure
+ * @param from		The offset to lock
+ * @param len		number of bytes to lock
+ * @param retlen	pointer to variable to store the number of lock bytes
+ * @param buf		the databuffer to put/get data
+ *
+ * Lock OTP block area.
+ */
+static int do_otp_lock(struct mtd_info *mtd, loff_t from, size_t len,
+		size_t *retlen, u_char *buf)
+{
+	struct onenand_chip *this = mtd->priv;
+	struct mtd_oob_ops ops;
+	int ret;
+
+	if (FLEXONENAND(this)) {
+
+		/* Enter OTP access mode */
+		this->command(mtd, ONENAND_CMD_OTP_ACCESS, 0, 0);
+		this->wait(mtd, FL_OTPING);
+		/*
+		 * For Flex-OneNAND, we write lock mark to 1st word of sector 4 of
+		 * main area of page 49.
+		 */
+		ops.len = mtd->writesize;
+		ops.ooblen = 0;
+		ops.datbuf = buf;
+		ops.oobbuf = NULL;
+		ret = onenand_write_ops_nolock(mtd, mtd->writesize * 49, &ops);
+		*retlen = ops.retlen;
+
+		/* Exit OTP access mode */
+		this->command(mtd, ONENAND_CMD_RESET, 0, 0);
+		this->wait(mtd, FL_RESETING);
+	} else {
+		ops.mode = MTD_OPS_PLACE_OOB;
+		ops.ooblen = len;
+		ops.oobbuf = buf;
+		ops.ooboffs = 0;
+		ret = onenand_otp_write_oob_nolock(mtd, from, &ops);
+		*retlen = ops.oobretlen;
+	}
+
+	return ret;
+}
+
+/**
+ * onenand_otp_walk - [DEFAULT] Handle OTP operation
+ * @param mtd		MTD device structure
+ * @param from		The offset to read/write
+ * @param len		number of bytes to read/write
+ * @param retlen	pointer to variable to store the number of read bytes
+ * @param buf		the databuffer to put/get data
+ * @param action	do given action
+ * @param mode		specify user and factory
+ *
+ * Handle OTP operation.
+ */
+static int onenand_otp_walk(struct mtd_info *mtd, loff_t from, size_t len,
+			size_t *retlen, u_char *buf,
+			otp_op_t action, int mode)
+{
+	struct onenand_chip *this = mtd->priv;
+	int otp_pages;
+	int density;
+	int ret = 0;
+
+	*retlen = 0;
+
+	density = onenand_get_density(this->device_id);
+	if (density < ONENAND_DEVICE_DENSITY_512Mb)
+		otp_pages = 20;
+	else
+		otp_pages = 50;
+
+	if (mode == MTD_OTP_FACTORY) {
+		from += mtd->writesize * otp_pages;
+		otp_pages = ONENAND_PAGES_PER_BLOCK - otp_pages;
+	}
+
+	/* Check User/Factory boundary */
+	if (mode == MTD_OTP_USER) {
+		if (mtd->writesize * otp_pages < from + len)
+			return 0;
+	} else {
+		if (mtd->writesize * otp_pages <  len)
+			return 0;
+	}
+
+	onenand_get_device(mtd, FL_OTPING);
+	while (len > 0 && otp_pages > 0) {
+		if (!action) {	/* OTP Info functions */
+			struct otp_info *otpinfo;
+
+			len -= sizeof(struct otp_info);
+			if (len <= 0) {
+				ret = -ENOSPC;
+				break;
+			}
+
+			otpinfo = (struct otp_info *) buf;
+			otpinfo->start = from;
+			otpinfo->length = mtd->writesize;
+			otpinfo->locked = 0;
+
+			from += mtd->writesize;
+			buf += sizeof(struct otp_info);
+			*retlen += sizeof(struct otp_info);
+		} else {
+			size_t tmp_retlen;
+
+			ret = action(mtd, from, len, &tmp_retlen, buf);
+			if (ret)
+				break;
+
+			buf += tmp_retlen;
+			len -= tmp_retlen;
+			*retlen += tmp_retlen;
+
+		}
+		otp_pages--;
+	}
+	onenand_release_device(mtd);
+
+	return ret;
+}
+
+/**
+ * onenand_get_fact_prot_info - [MTD Interface] Read factory OTP info
+ * @param mtd		MTD device structure
+ * @param len		number of bytes to read
+ * @param retlen	pointer to variable to store the number of read bytes
+ * @param buf		the databuffer to put/get data
+ *
+ * Read factory OTP info.
+ */
+static int onenand_get_fact_prot_info(struct mtd_info *mtd, size_t len,
+				      size_t *retlen, struct otp_info *buf)
+{
+	return onenand_otp_walk(mtd, 0, len, retlen, (u_char *) buf, NULL,
+				MTD_OTP_FACTORY);
+}
+
+/**
+ * onenand_read_fact_prot_reg - [MTD Interface] Read factory OTP area
+ * @param mtd		MTD device structure
+ * @param from		The offset to read
+ * @param len		number of bytes to read
+ * @param retlen	pointer to variable to store the number of read bytes
+ * @param buf		the databuffer to put/get data
+ *
+ * Read factory OTP area.
+ */
+static int onenand_read_fact_prot_reg(struct mtd_info *mtd, loff_t from,
+			size_t len, size_t *retlen, u_char *buf)
+{
+	return onenand_otp_walk(mtd, from, len, retlen, buf, do_otp_read, MTD_OTP_FACTORY);
+}
+
+/**
+ * onenand_get_user_prot_info - [MTD Interface] Read user OTP info
+ * @param mtd		MTD device structure
+ * @param retlen	pointer to variable to store the number of read bytes
+ * @param len		number of bytes to read
+ * @param buf		the databuffer to put/get data
+ *
+ * Read user OTP info.
+ */
+static int onenand_get_user_prot_info(struct mtd_info *mtd, size_t len,
+				      size_t *retlen, struct otp_info *buf)
+{
+	return onenand_otp_walk(mtd, 0, len, retlen, (u_char *) buf, NULL,
+				MTD_OTP_USER);
+}
+
+/**
+ * onenand_read_user_prot_reg - [MTD Interface] Read user OTP area
+ * @param mtd		MTD device structure
+ * @param from		The offset to read
+ * @param len		number of bytes to read
+ * @param retlen	pointer to variable to store the number of read bytes
+ * @param buf		the databuffer to put/get data
+ *
+ * Read user OTP area.
+ */
+static int onenand_read_user_prot_reg(struct mtd_info *mtd, loff_t from,
+			size_t len, size_t *retlen, u_char *buf)
+{
+	return onenand_otp_walk(mtd, from, len, retlen, buf, do_otp_read, MTD_OTP_USER);
+}
+
+/**
+ * onenand_write_user_prot_reg - [MTD Interface] Write user OTP area
+ * @param mtd		MTD device structure
+ * @param from		The offset to write
+ * @param len		number of bytes to write
+ * @param retlen	pointer to variable to store the number of write bytes
+ * @param buf		the databuffer to put/get data
+ *
+ * Write user OTP area.
+ */
+static int onenand_write_user_prot_reg(struct mtd_info *mtd, loff_t from,
+			size_t len, size_t *retlen, u_char *buf)
+{
+	return onenand_otp_walk(mtd, from, len, retlen, buf, do_otp_write, MTD_OTP_USER);
+}
+
+/**
+ * onenand_lock_user_prot_reg - [MTD Interface] Lock user OTP area
+ * @param mtd		MTD device structure
+ * @param from		The offset to lock
+ * @param len		number of bytes to unlock
+ *
+ * Write lock mark on spare area in page 0 in OTP block
+ */
+static int onenand_lock_user_prot_reg(struct mtd_info *mtd, loff_t from,
+			size_t len)
+{
+	struct onenand_chip *this = mtd->priv;
+	u_char *buf = FLEXONENAND(this) ? this->page_buf : this->oob_buf;
+	size_t retlen;
+	int ret;
+	unsigned int otp_lock_offset = ONENAND_OTP_LOCK_OFFSET;
+
+	memset(buf, 0xff, FLEXONENAND(this) ? this->writesize
+						 : mtd->oobsize);
+	/*
+	 * Write lock mark to 8th word of sector0 of page0 of the spare0.
+	 * We write 16 bytes spare area instead of 2 bytes.
+	 * For Flex-OneNAND, we write lock mark to 1st word of sector 4 of
+	 * main area of page 49.
+	 */
+
+	from = 0;
+	len = FLEXONENAND(this) ? mtd->writesize : 16;
+
+	/*
+	 * Note: OTP lock operation
+	 *       OTP block : 0xXXFC			XX 1111 1100
+	 *       1st block : 0xXXF3 (If chip support)	XX 1111 0011
+	 *       Both      : 0xXXF0 (If chip support)	XX 1111 0000
+	 */
+	if (FLEXONENAND(this))
+		otp_lock_offset = FLEXONENAND_OTP_LOCK_OFFSET;
+
+	/* ONENAND_OTP_AREA | ONENAND_OTP_BLOCK0 | ONENAND_OTP_AREA_BLOCK0 */
+	if (otp == 1)
+		buf[otp_lock_offset] = 0xFC;
+	else if (otp == 2)
+		buf[otp_lock_offset] = 0xF3;
+	else if (otp == 3)
+		buf[otp_lock_offset] = 0xF0;
+	else if (otp != 0)
+		printk(KERN_DEBUG "[OneNAND] Invalid option selected for OTP\n");
+
+	ret = onenand_otp_walk(mtd, from, len, &retlen, buf, do_otp_lock, MTD_OTP_USER);
+
+	return ret ? : retlen;
+}
+
+#endif	/* CONFIG_MTD_ONENAND_OTP */
+
+/**
+ * onenand_check_features - Check and set OneNAND features
+ * @param mtd		MTD data structure
+ *
+ * Check and set OneNAND features
+ * - lock scheme
+ * - two plane
+ */
+static void onenand_check_features(struct mtd_info *mtd)
+{
+	struct onenand_chip *this = mtd->priv;
+	unsigned int density, process, numbufs;
+
+	/* Lock scheme depends on density and process */
+	density = onenand_get_density(this->device_id);
+	process = this->version_id >> ONENAND_VERSION_PROCESS_SHIFT;
+	numbufs = this->read_word(this->base + ONENAND_REG_NUM_BUFFERS) >> 8;
+
+	/* Lock scheme */
+	switch (density) {
+	case ONENAND_DEVICE_DENSITY_4Gb:
+		if (ONENAND_IS_DDP(this))
+			this->options |= ONENAND_HAS_2PLANE;
+		else if (numbufs == 1) {
+			this->options |= ONENAND_HAS_4KB_PAGE;
+			this->options |= ONENAND_HAS_CACHE_PROGRAM;
+			/*
+			 * There are two different 4KiB pagesize chips
+			 * and no way to detect it by H/W config values.
+			 *
+			 * To detect the correct NOP for each chips,
+			 * It should check the version ID as workaround.
+			 *
+			 * Now it has as following
+			 * KFM4G16Q4M has NOP 4 with version ID 0x0131
+			 * KFM4G16Q5M has NOP 1 with versoin ID 0x013e
+			 */
+			if ((this->version_id & 0xf) == 0xe)
+				this->options |= ONENAND_HAS_NOP_1;
+		}
+
+	case ONENAND_DEVICE_DENSITY_2Gb:
+		/* 2Gb DDP does not have 2 plane */
+		if (!ONENAND_IS_DDP(this))
+			this->options |= ONENAND_HAS_2PLANE;
+		this->options |= ONENAND_HAS_UNLOCK_ALL;
+
+	case ONENAND_DEVICE_DENSITY_1Gb:
+		/* A-Die has all block unlock */
+		if (process)
+			this->options |= ONENAND_HAS_UNLOCK_ALL;
+		break;
+
+	default:
+		/* Some OneNAND has continuous lock scheme */
+		if (!process)
+			this->options |= ONENAND_HAS_CONT_LOCK;
+		break;
+	}
+
+	/* The MLC has 4KiB pagesize. */
+	if (ONENAND_IS_MLC(this))
+		this->options |= ONENAND_HAS_4KB_PAGE;
+
+	if (ONENAND_IS_4KB_PAGE(this))
+		this->options &= ~ONENAND_HAS_2PLANE;
+
+	if (FLEXONENAND(this)) {
+		this->options &= ~ONENAND_HAS_CONT_LOCK;
+		this->options |= ONENAND_HAS_UNLOCK_ALL;
+	}
+
+	if (this->options & ONENAND_HAS_CONT_LOCK)
+		printk(KERN_DEBUG "Lock scheme is Continuous Lock\n");
+	if (this->options & ONENAND_HAS_UNLOCK_ALL)
+		printk(KERN_DEBUG "Chip support all block unlock\n");
+	if (this->options & ONENAND_HAS_2PLANE)
+		printk(KERN_DEBUG "Chip has 2 plane\n");
+	if (this->options & ONENAND_HAS_4KB_PAGE)
+		printk(KERN_DEBUG "Chip has 4KiB pagesize\n");
+	if (this->options & ONENAND_HAS_CACHE_PROGRAM)
+		printk(KERN_DEBUG "Chip has cache program feature\n");
+}
+
+/**
+ * onenand_print_device_info - Print device & version ID
+ * @param device        device ID
+ * @param version	version ID
+ *
+ * Print device & version ID
+ */
+static void onenand_print_device_info(int device, int version)
+{
+	int vcc, demuxed, ddp, density, flexonenand;
+
+        vcc = device & ONENAND_DEVICE_VCC_MASK;
+        demuxed = device & ONENAND_DEVICE_IS_DEMUX;
+        ddp = device & ONENAND_DEVICE_IS_DDP;
+        density = onenand_get_density(device);
+	flexonenand = device & DEVICE_IS_FLEXONENAND;
+	printk(KERN_INFO "%s%sOneNAND%s %dMB %sV 16-bit (0x%02x)\n",
+		demuxed ? "" : "Muxed ",
+		flexonenand ? "Flex-" : "",
+                ddp ? "(DDP)" : "",
+                (16 << density),
+                vcc ? "2.65/3.3" : "1.8",
+                device);
+	printk(KERN_INFO "OneNAND version = 0x%04x\n", version);
+}
+
+static const struct onenand_manufacturers onenand_manuf_ids[] = {
+        {ONENAND_MFR_SAMSUNG, "Samsung"},
+	{ONENAND_MFR_NUMONYX, "Numonyx"},
+};
+
+/**
+ * onenand_check_maf - Check manufacturer ID
+ * @param manuf         manufacturer ID
+ *
+ * Check manufacturer ID
+ */
+static int onenand_check_maf(int manuf)
+{
+	int size = ARRAY_SIZE(onenand_manuf_ids);
+	char *name;
+        int i;
+
+	for (i = 0; i < size; i++)
+                if (manuf == onenand_manuf_ids[i].id)
+                        break;
+
+	if (i < size)
+		name = onenand_manuf_ids[i].name;
+	else
+		name = "Unknown";
+
+	printk(KERN_DEBUG "OneNAND Manufacturer: %s (0x%0x)\n", name, manuf);
+
+	return (i == size);
+}
+
+/**
+* flexonenand_get_boundary	- Reads the SLC boundary
+* @param onenand_info		- onenand info structure
+**/
+static int flexonenand_get_boundary(struct mtd_info *mtd)
+{
+	struct onenand_chip *this = mtd->priv;
+	unsigned die, bdry;
+	int syscfg, locked;
+
+	/* Disable ECC */
+	syscfg = this->read_word(this->base + ONENAND_REG_SYS_CFG1);
+	this->write_word((syscfg | 0x0100), this->base + ONENAND_REG_SYS_CFG1);
+
+	for (die = 0; die < this->dies; die++) {
+		this->command(mtd, FLEXONENAND_CMD_PI_ACCESS, die, 0);
+		this->wait(mtd, FL_SYNCING);
+
+		this->command(mtd, FLEXONENAND_CMD_READ_PI, die, 0);
+		this->wait(mtd, FL_READING);
+
+		bdry = this->read_word(this->base + ONENAND_DATARAM);
+		if ((bdry >> FLEXONENAND_PI_UNLOCK_SHIFT) == 3)
+			locked = 0;
+		else
+			locked = 1;
+		this->boundary[die] = bdry & FLEXONENAND_PI_MASK;
+
+		this->command(mtd, ONENAND_CMD_RESET, 0, 0);
+		this->wait(mtd, FL_RESETING);
+
+		printk(KERN_INFO "Die %d boundary: %d%s\n", die,
+		       this->boundary[die], locked ? "(Locked)" : "(Unlocked)");
+	}
+
+	/* Enable ECC */
+	this->write_word(syscfg, this->base + ONENAND_REG_SYS_CFG1);
+	return 0;
+}
+
+/**
+ * flexonenand_get_size - Fill up fields in onenand_chip and mtd_info
+ * 			  boundary[], diesize[], mtd->size, mtd->erasesize
+ * @param mtd		- MTD device structure
+ */
+static void flexonenand_get_size(struct mtd_info *mtd)
+{
+	struct onenand_chip *this = mtd->priv;
+	int die, i, eraseshift, density;
+	int blksperdie, maxbdry;
+	loff_t ofs;
+
+	density = onenand_get_density(this->device_id);
+	blksperdie = ((loff_t)(16 << density) << 20) >> (this->erase_shift);
+	blksperdie >>= ONENAND_IS_DDP(this) ? 1 : 0;
+	maxbdry = blksperdie - 1;
+	eraseshift = this->erase_shift - 1;
+
+	mtd->numeraseregions = this->dies << 1;
+
+	/* This fills up the device boundary */
+	flexonenand_get_boundary(mtd);
+	die = ofs = 0;
+	i = -1;
+	for (; die < this->dies; die++) {
+		if (!die || this->boundary[die-1] != maxbdry) {
+			i++;
+			mtd->eraseregions[i].offset = ofs;
+			mtd->eraseregions[i].erasesize = 1 << eraseshift;
+			mtd->eraseregions[i].numblocks =
+							this->boundary[die] + 1;
+			ofs += mtd->eraseregions[i].numblocks << eraseshift;
+			eraseshift++;
+		} else {
+			mtd->numeraseregions -= 1;
+			mtd->eraseregions[i].numblocks +=
+							this->boundary[die] + 1;
+			ofs += (this->boundary[die] + 1) << (eraseshift - 1);
+		}
+		if (this->boundary[die] != maxbdry) {
+			i++;
+			mtd->eraseregions[i].offset = ofs;
+			mtd->eraseregions[i].erasesize = 1 << eraseshift;
+			mtd->eraseregions[i].numblocks = maxbdry ^
+							 this->boundary[die];
+			ofs += mtd->eraseregions[i].numblocks << eraseshift;
+			eraseshift--;
+		} else
+			mtd->numeraseregions -= 1;
+	}
+
+	/* Expose MLC erase size except when all blocks are SLC */
+	mtd->erasesize = 1 << this->erase_shift;
+	if (mtd->numeraseregions == 1)
+		mtd->erasesize >>= 1;
+
+	printk(KERN_INFO "Device has %d eraseregions\n", mtd->numeraseregions);
+	for (i = 0; i < mtd->numeraseregions; i++)
+		printk(KERN_INFO "[offset: 0x%08x, erasesize: 0x%05x,"
+			" numblocks: %04u]\n",
+			(unsigned int) mtd->eraseregions[i].offset,
+			mtd->eraseregions[i].erasesize,
+			mtd->eraseregions[i].numblocks);
+
+	for (die = 0, mtd->size = 0; die < this->dies; die++) {
+		this->diesize[die] = (loff_t)blksperdie << this->erase_shift;
+		this->diesize[die] -= (loff_t)(this->boundary[die] + 1)
+						 << (this->erase_shift - 1);
+		mtd->size += this->diesize[die];
+	}
+}
+
+/**
+ * flexonenand_check_blocks_erased - Check if blocks are erased
+ * @param mtd_info	- mtd info structure
+ * @param start		- first erase block to check
+ * @param end		- last erase block to check
+ *
+ * Converting an unerased block from MLC to SLC
+ * causes byte values to change. Since both data and its ECC
+ * have changed, reads on the block give uncorrectable error.
+ * This might lead to the block being detected as bad.
+ *
+ * Avoid this by ensuring that the block to be converted is
+ * erased.
+ */
+static int flexonenand_check_blocks_erased(struct mtd_info *mtd, int start, int end)
+{
+	struct onenand_chip *this = mtd->priv;
+	int i, ret;
+	int block;
+	struct mtd_oob_ops ops = {
+		.mode = MTD_OPS_PLACE_OOB,
+		.ooboffs = 0,
+		.ooblen	= mtd->oobsize,
+		.datbuf	= NULL,
+		.oobbuf	= this->oob_buf,
+	};
+	loff_t addr;
+
+	printk(KERN_DEBUG "Check blocks from %d to %d\n", start, end);
+
+	for (block = start; block <= end; block++) {
+		addr = flexonenand_addr(this, block);
+		if (onenand_block_isbad_nolock(mtd, addr, 0))
+			continue;
+
+		/*
+		 * Since main area write results in ECC write to spare,
+		 * it is sufficient to check only ECC bytes for change.
+		 */
+		ret = onenand_read_oob_nolock(mtd, addr, &ops);
+		if (ret)
+			return ret;
+
+		for (i = 0; i < mtd->oobsize; i++)
+			if (this->oob_buf[i] != 0xff)
+				break;
+
+		if (i != mtd->oobsize) {
+			printk(KERN_WARNING "%s: Block %d not erased.\n",
+				__func__, block);
+			return 1;
+		}
+	}
+
+	return 0;
+}
+
+/**
+ * flexonenand_set_boundary	- Writes the SLC boundary
+ * @param mtd			- mtd info structure
+ */
+static int flexonenand_set_boundary(struct mtd_info *mtd, int die,
+				    int boundary, int lock)
+{
+	struct onenand_chip *this = mtd->priv;
+	int ret, density, blksperdie, old, new, thisboundary;
+	loff_t addr;
+
+	/* Change only once for SDP Flex-OneNAND */
+	if (die && (!ONENAND_IS_DDP(this)))
+		return 0;
+
+	/* boundary value of -1 indicates no required change */
+	if (boundary < 0 || boundary == this->boundary[die])
+		return 0;
+
+	density = onenand_get_density(this->device_id);
+	blksperdie = ((16 << density) << 20) >> this->erase_shift;
+	blksperdie >>= ONENAND_IS_DDP(this) ? 1 : 0;
+
+	if (boundary >= blksperdie) {
+		printk(KERN_ERR "%s: Invalid boundary value. "
+				"Boundary not changed.\n", __func__);
+		return -EINVAL;
+	}
+
+	/* Check if converting blocks are erased */
+	old = this->boundary[die] + (die * this->density_mask);
+	new = boundary + (die * this->density_mask);
+	ret = flexonenand_check_blocks_erased(mtd, min(old, new) + 1, max(old, new));
+	if (ret) {
+		printk(KERN_ERR "%s: Please erase blocks "
+				"before boundary change\n", __func__);
+		return ret;
+	}
+
+	this->command(mtd, FLEXONENAND_CMD_PI_ACCESS, die, 0);
+	this->wait(mtd, FL_SYNCING);
+
+	/* Check is boundary is locked */
+	this->command(mtd, FLEXONENAND_CMD_READ_PI, die, 0);
+	this->wait(mtd, FL_READING);
+
+	thisboundary = this->read_word(this->base + ONENAND_DATARAM);
+	if ((thisboundary >> FLEXONENAND_PI_UNLOCK_SHIFT) != 3) {
+		printk(KERN_ERR "%s: boundary locked\n", __func__);
+		ret = 1;
+		goto out;
+	}
+
+	printk(KERN_INFO "Changing die %d boundary: %d%s\n",
+			die, boundary, lock ? "(Locked)" : "(Unlocked)");
+
+	addr = die ? this->diesize[0] : 0;
+
+	boundary &= FLEXONENAND_PI_MASK;
+	boundary |= lock ? 0 : (3 << FLEXONENAND_PI_UNLOCK_SHIFT);
+
+	this->command(mtd, ONENAND_CMD_ERASE, addr, 0);
+	ret = this->wait(mtd, FL_ERASING);
+	if (ret) {
+		printk(KERN_ERR "%s: Failed PI erase for Die %d\n",
+		       __func__, die);
+		goto out;
+	}
+
+	this->write_word(boundary, this->base + ONENAND_DATARAM);
+	this->command(mtd, ONENAND_CMD_PROG, addr, 0);
+	ret = this->wait(mtd, FL_WRITING);
+	if (ret) {
+		printk(KERN_ERR "%s: Failed PI write for Die %d\n",
+			__func__, die);
+		goto out;
+	}
+
+	this->command(mtd, FLEXONENAND_CMD_PI_UPDATE, die, 0);
+	ret = this->wait(mtd, FL_WRITING);
+out:
+	this->write_word(ONENAND_CMD_RESET, this->base + ONENAND_REG_COMMAND);
+	this->wait(mtd, FL_RESETING);
+	if (!ret)
+		/* Recalculate device size on boundary change*/
+		flexonenand_get_size(mtd);
+
+	return ret;
+}
+
+/**
+ * onenand_chip_probe - [OneNAND Interface] The generic chip probe
+ * @param mtd		MTD device structure
+ *
+ * OneNAND detection method:
+ *   Compare the values from command with ones from register
+ */
+static int onenand_chip_probe(struct mtd_info *mtd)
+{
+	struct onenand_chip *this = mtd->priv;
+	int bram_maf_id, bram_dev_id, maf_id, dev_id;
+	int syscfg;
+
+	/* Save system configuration 1 */
+	syscfg = this->read_word(this->base + ONENAND_REG_SYS_CFG1);
+	/* Clear Sync. Burst Read mode to read BootRAM */
+	this->write_word((syscfg & ~ONENAND_SYS_CFG1_SYNC_READ & ~ONENAND_SYS_CFG1_SYNC_WRITE), this->base + ONENAND_REG_SYS_CFG1);
+
+	/* Send the command for reading device ID from BootRAM */
+	this->write_word(ONENAND_CMD_READID, this->base + ONENAND_BOOTRAM);
+
+	/* Read manufacturer and device IDs from BootRAM */
+	bram_maf_id = this->read_word(this->base + ONENAND_BOOTRAM + 0x0);
+	bram_dev_id = this->read_word(this->base + ONENAND_BOOTRAM + 0x2);
+
+	/* Reset OneNAND to read default register values */
+	this->write_word(ONENAND_CMD_RESET, this->base + ONENAND_BOOTRAM);
+	/* Wait reset */
+	this->wait(mtd, FL_RESETING);
+
+	/* Restore system configuration 1 */
+	this->write_word(syscfg, this->base + ONENAND_REG_SYS_CFG1);
+
+	/* Check manufacturer ID */
+	if (onenand_check_maf(bram_maf_id))
+		return -ENXIO;
+
+	/* Read manufacturer and device IDs from Register */
+	maf_id = this->read_word(this->base + ONENAND_REG_MANUFACTURER_ID);
+	dev_id = this->read_word(this->base + ONENAND_REG_DEVICE_ID);
+
+	/* Check OneNAND device */
+	if (maf_id != bram_maf_id || dev_id != bram_dev_id)
+		return -ENXIO;
+
+	return 0;
+}
+
+/**
+ * onenand_probe - [OneNAND Interface] Probe the OneNAND device
+ * @param mtd		MTD device structure
+ */
+static int onenand_probe(struct mtd_info *mtd)
+{
+	struct onenand_chip *this = mtd->priv;
+	int dev_id, ver_id;
+	int density;
+	int ret;
+
+	ret = this->chip_probe(mtd);
+	if (ret)
+		return ret;
+
+	/* Device and version IDs from Register */
+	dev_id = this->read_word(this->base + ONENAND_REG_DEVICE_ID);
+	ver_id = this->read_word(this->base + ONENAND_REG_VERSION_ID);
+	this->technology = this->read_word(this->base + ONENAND_REG_TECHNOLOGY);
+
+	/* Flash device information */
+	onenand_print_device_info(dev_id, ver_id);
+	this->device_id = dev_id;
+	this->version_id = ver_id;
+
+	/* Check OneNAND features */
+	onenand_check_features(mtd);
+
+	density = onenand_get_density(dev_id);
+	if (FLEXONENAND(this)) {
+		this->dies = ONENAND_IS_DDP(this) ? 2 : 1;
+		/* Maximum possible erase regions */
+		mtd->numeraseregions = this->dies << 1;
+		mtd->eraseregions = kzalloc(sizeof(struct mtd_erase_region_info)
+					* (this->dies << 1), GFP_KERNEL);
+		if (!mtd->eraseregions)
+			return -ENOMEM;
+	}
+
+	/*
+	 * For Flex-OneNAND, chipsize represents maximum possible device size.
+	 * mtd->size represents the actual device size.
+	 */
+	this->chipsize = (16 << density) << 20;
+
+	/* OneNAND page size & block size */
+	/* The data buffer size is equal to page size */
+	mtd->writesize = this->read_word(this->base + ONENAND_REG_DATA_BUFFER_SIZE);
+	/* We use the full BufferRAM */
+	if (ONENAND_IS_4KB_PAGE(this))
+		mtd->writesize <<= 1;
+
+	mtd->oobsize = mtd->writesize >> 5;
+	/* Pages per a block are always 64 in OneNAND */
+	mtd->erasesize = mtd->writesize << 6;
+	/*
+	 * Flex-OneNAND SLC area has 64 pages per block.
+	 * Flex-OneNAND MLC area has 128 pages per block.
+	 * Expose MLC erase size to find erase_shift and page_mask.
+	 */
+	if (FLEXONENAND(this))
+		mtd->erasesize <<= 1;
+
+	this->erase_shift = ffs(mtd->erasesize) - 1;
+	this->page_shift = ffs(mtd->writesize) - 1;
+	this->page_mask = (1 << (this->erase_shift - this->page_shift)) - 1;
+	/* Set density mask. it is used for DDP */
+	if (ONENAND_IS_DDP(this))
+		this->density_mask = this->chipsize >> (this->erase_shift + 1);
+	/* It's real page size */
+	this->writesize = mtd->writesize;
+
+	/* REVISIT: Multichip handling */
+
+	if (FLEXONENAND(this))
+		flexonenand_get_size(mtd);
+	else
+		mtd->size = this->chipsize;
+
+	/*
+	 * We emulate the 4KiB page and 256KiB erase block size
+	 * But oobsize is still 64 bytes.
+	 * It is only valid if you turn on 2X program support,
+	 * Otherwise it will be ignored by compiler.
+	 */
+	if (ONENAND_IS_2PLANE(this)) {
+		mtd->writesize <<= 1;
+		mtd->erasesize <<= 1;
+	}
+
+	return 0;
+}
+
+/**
+ * onenand_suspend - [MTD Interface] Suspend the OneNAND flash
+ * @param mtd		MTD device structure
+ */
+static int onenand_suspend(struct mtd_info *mtd)
+{
+	return onenand_get_device(mtd, FL_PM_SUSPENDED);
+}
+
+/**
+ * onenand_resume - [MTD Interface] Resume the OneNAND flash
+ * @param mtd		MTD device structure
+ */
+static void onenand_resume(struct mtd_info *mtd)
+{
+	struct onenand_chip *this = mtd->priv;
+
+	if (this->state == FL_PM_SUSPENDED)
+		onenand_release_device(mtd);
+	else
+		printk(KERN_ERR "%s: resume() called for the chip which is not "
+				"in suspended state\n", __func__);
+}
+
+/**
+ * onenand_scan - [OneNAND Interface] Scan for the OneNAND device
+ * @param mtd		MTD device structure
+ * @param maxchips	Number of chips to scan for
+ *
+ * This fills out all the not initialized function pointers
+ * with the defaults.
+ * The flash ID is read and the mtd/chip structures are
+ * filled with the appropriate values.
+ */
+int onenand_scan(struct mtd_info *mtd, int maxchips)
+{
+	int i, ret;
+	struct onenand_chip *this = mtd->priv;
+
+	if (!this->read_word)
+		this->read_word = onenand_readw;
+	if (!this->write_word)
+		this->write_word = onenand_writew;
+
+	if (!this->command)
+		this->command = onenand_command;
+	if (!this->wait)
+		onenand_setup_wait(mtd);
+	if (!this->bbt_wait)
+		this->bbt_wait = onenand_bbt_wait;
+	if (!this->unlock_all)
+		this->unlock_all = onenand_unlock_all;
+
+	if (!this->chip_probe)
+		this->chip_probe = onenand_chip_probe;
+
+	if (!this->read_bufferram)
+		this->read_bufferram = onenand_read_bufferram;
+	if (!this->write_bufferram)
+		this->write_bufferram = onenand_write_bufferram;
+
+	if (!this->block_markbad)
+		this->block_markbad = onenand_default_block_markbad;
+	if (!this->scan_bbt)
+		this->scan_bbt = onenand_default_bbt;
+
+	if (onenand_probe(mtd))
+		return -ENXIO;
+
+	/* Set Sync. Burst Read after probing */
+	if (this->mmcontrol) {
+		printk(KERN_INFO "OneNAND Sync. Burst Read support\n");
+		this->read_bufferram = onenand_sync_read_bufferram;
+	}
+
+	/* Allocate buffers, if necessary */
+	if (!this->page_buf) {
+		this->page_buf = kzalloc(mtd->writesize, GFP_KERNEL);
+		if (!this->page_buf)
+			return -ENOMEM;
+#ifdef CONFIG_MTD_ONENAND_VERIFY_WRITE
+		this->verify_buf = kzalloc(mtd->writesize, GFP_KERNEL);
+		if (!this->verify_buf) {
+			kfree(this->page_buf);
+			return -ENOMEM;
+		}
+#endif
+		this->options |= ONENAND_PAGEBUF_ALLOC;
+	}
+	if (!this->oob_buf) {
+		this->oob_buf = kzalloc(mtd->oobsize, GFP_KERNEL);
+		if (!this->oob_buf) {
+			if (this->options & ONENAND_PAGEBUF_ALLOC) {
+				this->options &= ~ONENAND_PAGEBUF_ALLOC;
+				kfree(this->page_buf);
+			}
+			return -ENOMEM;
+		}
+		this->options |= ONENAND_OOBBUF_ALLOC;
+	}
+
+	this->state = FL_READY;
+	init_waitqueue_head(&this->wq);
+	spin_lock_init(&this->chip_lock);
+
+	/*
+	 * Allow subpage writes up to oobsize.
+	 */
+	switch (mtd->oobsize) {
+	case 128:
+		if (FLEXONENAND(this)) {
+			mtd_set_ooblayout(mtd, &flexonenand_ooblayout_ops);
+			mtd->subpage_sft = 0;
+		} else {
+			mtd_set_ooblayout(mtd, &onenand_oob_128_ooblayout_ops);
+			mtd->subpage_sft = 2;
+		}
+		if (ONENAND_IS_NOP_1(this))
+			mtd->subpage_sft = 0;
+		break;
+	case 64:
+		mtd_set_ooblayout(mtd, &onenand_oob_32_64_ooblayout_ops);
+		mtd->subpage_sft = 2;
+		break;
+
+	case 32:
+		mtd_set_ooblayout(mtd, &onenand_oob_32_64_ooblayout_ops);
+		mtd->subpage_sft = 1;
+		break;
+
+	default:
+		printk(KERN_WARNING "%s: No OOB scheme defined for oobsize %d\n",
+			__func__, mtd->oobsize);
+		mtd->subpage_sft = 0;
+		/* To prevent kernel oops */
+		mtd_set_ooblayout(mtd, &onenand_oob_32_64_ooblayout_ops);
+		break;
+	}
+
+	this->subpagesize = mtd->writesize >> mtd->subpage_sft;
+
+	/*
+	 * The number of bytes available for a client to place data into
+	 * the out of band area
+	 */
+	ret = mtd_ooblayout_count_freebytes(mtd);
+	if (ret < 0)
+		ret = 0;
+
+	mtd->oobavail = ret;
+
+	mtd->ecc_strength = 1;
+
+	/* Fill in remaining MTD driver data */
+	mtd->type = ONENAND_IS_MLC(this) ? MTD_MLCNANDFLASH : MTD_NANDFLASH;
+	mtd->flags = MTD_CAP_NANDFLASH;
+	mtd->_erase = onenand_erase;
+	mtd->_point = NULL;
+	mtd->_unpoint = NULL;
+	mtd->_read_oob = onenand_read_oob;
+	mtd->_write_oob = onenand_write_oob;
+	mtd->_panic_write = onenand_panic_write;
+#ifdef CONFIG_MTD_ONENAND_OTP
+	mtd->_get_fact_prot_info = onenand_get_fact_prot_info;
+	mtd->_read_fact_prot_reg = onenand_read_fact_prot_reg;
+	mtd->_get_user_prot_info = onenand_get_user_prot_info;
+	mtd->_read_user_prot_reg = onenand_read_user_prot_reg;
+	mtd->_write_user_prot_reg = onenand_write_user_prot_reg;
+	mtd->_lock_user_prot_reg = onenand_lock_user_prot_reg;
+#endif
+	mtd->_sync = onenand_sync;
+	mtd->_lock = onenand_lock;
+	mtd->_unlock = onenand_unlock;
+	mtd->_suspend = onenand_suspend;
+	mtd->_resume = onenand_resume;
+	mtd->_block_isbad = onenand_block_isbad;
+	mtd->_block_markbad = onenand_block_markbad;
+	mtd->owner = THIS_MODULE;
+	mtd->writebufsize = mtd->writesize;
+
+	/* Unlock whole block */
+	if (!(this->options & ONENAND_SKIP_INITIAL_UNLOCKING))
+		this->unlock_all(mtd);
+
+	ret = this->scan_bbt(mtd);
+	if ((!FLEXONENAND(this)) || ret)
+		return ret;
+
+	/* Change Flex-OneNAND boundaries if required */
+	for (i = 0; i < MAX_DIES; i++)
+		flexonenand_set_boundary(mtd, i, flex_bdry[2 * i],
+						 flex_bdry[(2 * i) + 1]);
+
+	return 0;
+}
+
+/**
+ * onenand_release - [OneNAND Interface] Free resources held by the OneNAND device
+ * @param mtd		MTD device structure
+ */
+void onenand_release(struct mtd_info *mtd)
+{
+	struct onenand_chip *this = mtd->priv;
+
+	/* Deregister partitions */
+	mtd_device_unregister(mtd);
+
+	/* Free bad block table memory, if allocated */
+	if (this->bbm) {
+		struct bbm_info *bbm = this->bbm;
+		kfree(bbm->bbt);
+		kfree(this->bbm);
+	}
+	/* Buffers allocated by onenand_scan */
+	if (this->options & ONENAND_PAGEBUF_ALLOC) {
+		kfree(this->page_buf);
+#ifdef CONFIG_MTD_ONENAND_VERIFY_WRITE
+		kfree(this->verify_buf);
+#endif
+	}
+	if (this->options & ONENAND_OOBBUF_ALLOC)
+		kfree(this->oob_buf);
+	kfree(mtd->eraseregions);
+}
+
+EXPORT_SYMBOL_GPL(onenand_scan);
+EXPORT_SYMBOL_GPL(onenand_release);
+
+MODULE_LICENSE("GPL");
+MODULE_AUTHOR("Kyungmin Park <kyungmin.park@samsung.com>");
+MODULE_DESCRIPTION("Generic OneNAND flash driver code");
diff --git a/drivers/mtd/nand/onenand/onenand_bbt.c b/drivers/mtd/nand/onenand/onenand_bbt.c
new file mode 100644
index 000000000000..dde20487937d
--- /dev/null
+++ b/drivers/mtd/nand/onenand/onenand_bbt.c
@@ -0,0 +1,248 @@
+// SPDX-License-Identifier: GPL-2.0
+/*
+ *  Bad Block Table support for the OneNAND driver
+ *
+ *  Copyright(c) 2005 Samsung Electronics
+ *  Kyungmin Park <kyungmin.park@samsung.com>
+ *
+ *  Derived from nand_bbt.c
+ *
+ *  TODO:
+ *    Split BBT core and chip specific BBT.
+ */
+
+#include <linux/slab.h>
+#include <linux/mtd/mtd.h>
+#include <linux/mtd/onenand.h>
+#include <linux/export.h>
+
+/**
+ * check_short_pattern - [GENERIC] check if a pattern is in the buffer
+ * @param buf		the buffer to search
+ * @param len		the length of buffer to search
+ * @param paglen	the pagelength
+ * @param td		search pattern descriptor
+ *
+ * Check for a pattern at the given place. Used to search bad block
+ * tables and good / bad block identifiers. Same as check_pattern, but
+ * no optional empty check and the pattern is expected to start
+ * at offset 0.
+ *
+ */
+static int check_short_pattern(uint8_t *buf, int len, int paglen, struct nand_bbt_descr *td)
+{
+	int i;
+	uint8_t *p = buf;
+
+	/* Compare the pattern */
+	for (i = 0; i < td->len; i++) {
+		if (p[i] != td->pattern[i])
+			return -1;
+	}
+        return 0;
+}
+
+/**
+ * create_bbt - [GENERIC] Create a bad block table by scanning the device
+ * @param mtd		MTD device structure
+ * @param buf		temporary buffer
+ * @param bd		descriptor for the good/bad block search pattern
+ * @param chip		create the table for a specific chip, -1 read all chips.
+ *              Applies only if NAND_BBT_PERCHIP option is set
+ *
+ * Create a bad block table by scanning the device
+ * for the given good/bad block identify pattern
+ */
+static int create_bbt(struct mtd_info *mtd, uint8_t *buf, struct nand_bbt_descr *bd, int chip)
+{
+	struct onenand_chip *this = mtd->priv;
+	struct bbm_info *bbm = this->bbm;
+	int i, j, numblocks, len, scanlen;
+	int startblock;
+	loff_t from;
+	size_t readlen, ooblen;
+	struct mtd_oob_ops ops;
+	int rgn;
+
+	printk(KERN_INFO "Scanning device for bad blocks\n");
+
+	len = 2;
+
+	/* We need only read few bytes from the OOB area */
+	scanlen = ooblen = 0;
+	readlen = bd->len;
+
+	/* chip == -1 case only */
+	/* Note that numblocks is 2 * (real numblocks) here;
+	 * see i += 2 below as it makses shifting and masking less painful
+	 */
+	numblocks = this->chipsize >> (bbm->bbt_erase_shift - 1);
+	startblock = 0;
+	from = 0;
+
+	ops.mode = MTD_OPS_PLACE_OOB;
+	ops.ooblen = readlen;
+	ops.oobbuf = buf;
+	ops.len = ops.ooboffs = ops.retlen = ops.oobretlen = 0;
+
+	for (i = startblock; i < numblocks; ) {
+		int ret;
+
+		for (j = 0; j < len; j++) {
+			/* No need to read pages fully,
+			 * just read required OOB bytes */
+			ret = onenand_bbt_read_oob(mtd,
+				from + j * this->writesize + bd->offs, &ops);
+
+			/* If it is a initial bad block, just ignore it */
+			if (ret == ONENAND_BBT_READ_FATAL_ERROR)
+				return -EIO;
+
+			if (ret || check_short_pattern(&buf[j * scanlen],
+					       scanlen, this->writesize, bd)) {
+				bbm->bbt[i >> 3] |= 0x03 << (i & 0x6);
+				printk(KERN_INFO "OneNAND eraseblock %d is an "
+					"initial bad block\n", i >> 1);
+				mtd->ecc_stats.badblocks++;
+				break;
+			}
+		}
+		i += 2;
+
+		if (FLEXONENAND(this)) {
+			rgn = flexonenand_region(mtd, from);
+			from += mtd->eraseregions[rgn].erasesize;
+		} else
+			from += (1 << bbm->bbt_erase_shift);
+	}
+
+	return 0;
+}
+
+
+/**
+ * onenand_memory_bbt - [GENERIC] create a memory based bad block table
+ * @param mtd		MTD device structure
+ * @param bd		descriptor for the good/bad block search pattern
+ *
+ * The function creates a memory based bbt by scanning the device
+ * for manufacturer / software marked good / bad blocks
+ */
+static inline int onenand_memory_bbt (struct mtd_info *mtd, struct nand_bbt_descr *bd)
+{
+	struct onenand_chip *this = mtd->priv;
+
+	return create_bbt(mtd, this->page_buf, bd, -1);
+}
+
+/**
+ * onenand_isbad_bbt - [OneNAND Interface] Check if a block is bad
+ * @param mtd		MTD device structure
+ * @param offs		offset in the device
+ * @param allowbbt	allow access to bad block table region
+ */
+static int onenand_isbad_bbt(struct mtd_info *mtd, loff_t offs, int allowbbt)
+{
+	struct onenand_chip *this = mtd->priv;
+	struct bbm_info *bbm = this->bbm;
+	int block;
+	uint8_t res;
+
+	/* Get block number * 2 */
+	block = (int) (onenand_block(this, offs) << 1);
+	res = (bbm->bbt[block >> 3] >> (block & 0x06)) & 0x03;
+
+	pr_debug("onenand_isbad_bbt: bbt info for offs 0x%08x: (block %d) 0x%02x\n",
+		(unsigned int) offs, block >> 1, res);
+
+	switch ((int) res) {
+	case 0x00:	return 0;
+	case 0x01:	return 1;
+	case 0x02:	return allowbbt ? 0 : 1;
+	}
+
+	return 1;
+}
+
+/**
+ * onenand_scan_bbt - [OneNAND Interface] scan, find, read and maybe create bad block table(s)
+ * @param mtd		MTD device structure
+ * @param bd		descriptor for the good/bad block search pattern
+ *
+ * The function checks, if a bad block table(s) is/are already
+ * available. If not it scans the device for manufacturer
+ * marked good / bad blocks and writes the bad block table(s) to
+ * the selected place.
+ *
+ * The bad block table memory is allocated here. It is freed
+ * by the onenand_release function.
+ *
+ */
+static int onenand_scan_bbt(struct mtd_info *mtd, struct nand_bbt_descr *bd)
+{
+	struct onenand_chip *this = mtd->priv;
+	struct bbm_info *bbm = this->bbm;
+	int len, ret = 0;
+
+	len = this->chipsize >> (this->erase_shift + 2);
+	/* Allocate memory (2bit per block) and clear the memory bad block table */
+	bbm->bbt = kzalloc(len, GFP_KERNEL);
+	if (!bbm->bbt)
+		return -ENOMEM;
+
+	/* Set the bad block position */
+	bbm->badblockpos = ONENAND_BADBLOCK_POS;
+
+	/* Set erase shift */
+	bbm->bbt_erase_shift = this->erase_shift;
+
+	if (!bbm->isbad_bbt)
+		bbm->isbad_bbt = onenand_isbad_bbt;
+
+	/* Scan the device to build a memory based bad block table */
+	if ((ret = onenand_memory_bbt(mtd, bd))) {
+		printk(KERN_ERR "onenand_scan_bbt: Can't scan flash and build the RAM-based BBT\n");
+		kfree(bbm->bbt);
+		bbm->bbt = NULL;
+	}
+
+	return ret;
+}
+
+/*
+ * Define some generic bad / good block scan pattern which are used
+ * while scanning a device for factory marked good / bad blocks.
+ */
+static uint8_t scan_ff_pattern[] = { 0xff, 0xff };
+
+static struct nand_bbt_descr largepage_memorybased = {
+	.options = 0,
+	.offs = 0,
+	.len = 2,
+	.pattern = scan_ff_pattern,
+};
+
+/**
+ * onenand_default_bbt - [OneNAND Interface] Select a default bad block table for the device
+ * @param mtd		MTD device structure
+ *
+ * This function selects the default bad block table
+ * support for the device and calls the onenand_scan_bbt function
+ */
+int onenand_default_bbt(struct mtd_info *mtd)
+{
+	struct onenand_chip *this = mtd->priv;
+	struct bbm_info *bbm;
+
+	this->bbm = kzalloc(sizeof(struct bbm_info), GFP_KERNEL);
+	if (!this->bbm)
+		return -ENOMEM;
+
+	bbm = this->bbm;
+
+	/* 1KB page has same configuration as 2KB page */
+	if (!bbm->badblock_pattern)
+		bbm->badblock_pattern = &largepage_memorybased;
+
+	return onenand_scan_bbt(mtd, bbm->badblock_pattern);
+}
diff --git a/drivers/mtd/nand/onenand/samsung.c b/drivers/mtd/nand/onenand/samsung.c
new file mode 100644
index 000000000000..2e9d076e445a
--- /dev/null
+++ b/drivers/mtd/nand/onenand/samsung.c
@@ -0,0 +1,1012 @@
+/*
+ * Samsung S3C64XX/S5PC1XX OneNAND driver
+ *
+ *  Copyright © 2008-2010 Samsung Electronics
+ *  Kyungmin Park <kyungmin.park@samsung.com>
+ *  Marek Szyprowski <m.szyprowski@samsung.com>
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License version 2 as
+ * published by the Free Software Foundation.
+ *
+ * Implementation:
+ *	S3C64XX: emulate the pseudo BufferRAM
+ *	S5PC110: use DMA
+ */
+
+#include <linux/module.h>
+#include <linux/platform_device.h>
+#include <linux/sched.h>
+#include <linux/slab.h>
+#include <linux/mtd/mtd.h>
+#include <linux/mtd/onenand.h>
+#include <linux/mtd/partitions.h>
+#include <linux/dma-mapping.h>
+#include <linux/interrupt.h>
+#include <linux/io.h>
+
+#include "samsung.h"
+
+enum soc_type {
+	TYPE_S3C6400,
+	TYPE_S3C6410,
+	TYPE_S5PC110,
+};
+
+#define ONENAND_ERASE_STATUS		0x00
+#define ONENAND_MULTI_ERASE_SET		0x01
+#define ONENAND_ERASE_START		0x03
+#define ONENAND_UNLOCK_START		0x08
+#define ONENAND_UNLOCK_END		0x09
+#define ONENAND_LOCK_START		0x0A
+#define ONENAND_LOCK_END		0x0B
+#define ONENAND_LOCK_TIGHT_START	0x0C
+#define ONENAND_LOCK_TIGHT_END		0x0D
+#define ONENAND_UNLOCK_ALL		0x0E
+#define ONENAND_OTP_ACCESS		0x12
+#define ONENAND_SPARE_ACCESS_ONLY	0x13
+#define ONENAND_MAIN_ACCESS_ONLY	0x14
+#define ONENAND_ERASE_VERIFY		0x15
+#define ONENAND_MAIN_SPARE_ACCESS	0x16
+#define ONENAND_PIPELINE_READ		0x4000
+
+#define MAP_00				(0x0)
+#define MAP_01				(0x1)
+#define MAP_10				(0x2)
+#define MAP_11				(0x3)
+
+#define S3C64XX_CMD_MAP_SHIFT		24
+
+#define S3C6400_FBA_SHIFT		10
+#define S3C6400_FPA_SHIFT		4
+#define S3C6400_FSA_SHIFT		2
+
+#define S3C6410_FBA_SHIFT		12
+#define S3C6410_FPA_SHIFT		6
+#define S3C6410_FSA_SHIFT		4
+
+/* S5PC110 specific definitions */
+#define S5PC110_DMA_SRC_ADDR		0x400
+#define S5PC110_DMA_SRC_CFG		0x404
+#define S5PC110_DMA_DST_ADDR		0x408
+#define S5PC110_DMA_DST_CFG		0x40C
+#define S5PC110_DMA_TRANS_SIZE		0x414
+#define S5PC110_DMA_TRANS_CMD		0x418
+#define S5PC110_DMA_TRANS_STATUS	0x41C
+#define S5PC110_DMA_TRANS_DIR		0x420
+#define S5PC110_INTC_DMA_CLR		0x1004
+#define S5PC110_INTC_ONENAND_CLR	0x1008
+#define S5PC110_INTC_DMA_MASK		0x1024
+#define S5PC110_INTC_ONENAND_MASK	0x1028
+#define S5PC110_INTC_DMA_PEND		0x1044
+#define S5PC110_INTC_ONENAND_PEND	0x1048
+#define S5PC110_INTC_DMA_STATUS		0x1064
+#define S5PC110_INTC_ONENAND_STATUS	0x1068
+
+#define S5PC110_INTC_DMA_TD		(1 << 24)
+#define S5PC110_INTC_DMA_TE		(1 << 16)
+
+#define S5PC110_DMA_CFG_SINGLE		(0x0 << 16)
+#define S5PC110_DMA_CFG_4BURST		(0x2 << 16)
+#define S5PC110_DMA_CFG_8BURST		(0x3 << 16)
+#define S5PC110_DMA_CFG_16BURST		(0x4 << 16)
+
+#define S5PC110_DMA_CFG_INC		(0x0 << 8)
+#define S5PC110_DMA_CFG_CNT		(0x1 << 8)
+
+#define S5PC110_DMA_CFG_8BIT		(0x0 << 0)
+#define S5PC110_DMA_CFG_16BIT		(0x1 << 0)
+#define S5PC110_DMA_CFG_32BIT		(0x2 << 0)
+
+#define S5PC110_DMA_SRC_CFG_READ	(S5PC110_DMA_CFG_16BURST | \
+					S5PC110_DMA_CFG_INC | \
+					S5PC110_DMA_CFG_16BIT)
+#define S5PC110_DMA_DST_CFG_READ	(S5PC110_DMA_CFG_16BURST | \
+					S5PC110_DMA_CFG_INC | \
+					S5PC110_DMA_CFG_32BIT)
+#define S5PC110_DMA_SRC_CFG_WRITE	(S5PC110_DMA_CFG_16BURST | \
+					S5PC110_DMA_CFG_INC | \
+					S5PC110_DMA_CFG_32BIT)
+#define S5PC110_DMA_DST_CFG_WRITE	(S5PC110_DMA_CFG_16BURST | \
+					S5PC110_DMA_CFG_INC | \
+					S5PC110_DMA_CFG_16BIT)
+
+#define S5PC110_DMA_TRANS_CMD_TDC	(0x1 << 18)
+#define S5PC110_DMA_TRANS_CMD_TEC	(0x1 << 16)
+#define S5PC110_DMA_TRANS_CMD_TR	(0x1 << 0)
+
+#define S5PC110_DMA_TRANS_STATUS_TD	(0x1 << 18)
+#define S5PC110_DMA_TRANS_STATUS_TB	(0x1 << 17)
+#define S5PC110_DMA_TRANS_STATUS_TE	(0x1 << 16)
+
+#define S5PC110_DMA_DIR_READ		0x0
+#define S5PC110_DMA_DIR_WRITE		0x1
+
+struct s3c_onenand {
+	struct mtd_info	*mtd;
+	struct platform_device	*pdev;
+	enum soc_type	type;
+	void __iomem	*base;
+	void __iomem	*ahb_addr;
+	int		bootram_command;
+	void		*page_buf;
+	void		*oob_buf;
+	unsigned int	(*mem_addr)(int fba, int fpa, int fsa);
+	unsigned int	(*cmd_map)(unsigned int type, unsigned int val);
+	void __iomem	*dma_addr;
+	unsigned long	phys_base;
+	struct completion	complete;
+};
+
+#define CMD_MAP_00(dev, addr)		(dev->cmd_map(MAP_00, ((addr) << 1)))
+#define CMD_MAP_01(dev, mem_addr)	(dev->cmd_map(MAP_01, (mem_addr)))
+#define CMD_MAP_10(dev, mem_addr)	(dev->cmd_map(MAP_10, (mem_addr)))
+#define CMD_MAP_11(dev, addr)		(dev->cmd_map(MAP_11, ((addr) << 2)))
+
+static struct s3c_onenand *onenand;
+
+static inline int s3c_read_reg(int offset)
+{
+	return readl(onenand->base + offset);
+}
+
+static inline void s3c_write_reg(int value, int offset)
+{
+	writel(value, onenand->base + offset);
+}
+
+static inline int s3c_read_cmd(unsigned int cmd)
+{
+	return readl(onenand->ahb_addr + cmd);
+}
+
+static inline void s3c_write_cmd(int value, unsigned int cmd)
+{
+	writel(value, onenand->ahb_addr + cmd);
+}
+
+#ifdef SAMSUNG_DEBUG
+static void s3c_dump_reg(void)
+{
+	int i;
+
+	for (i = 0; i < 0x400; i += 0x40) {
+		printk(KERN_INFO "0x%08X: 0x%08x 0x%08x 0x%08x 0x%08x\n",
+			(unsigned int) onenand->base + i,
+			s3c_read_reg(i), s3c_read_reg(i + 0x10),
+			s3c_read_reg(i + 0x20), s3c_read_reg(i + 0x30));
+	}
+}
+#endif
+
+static unsigned int s3c64xx_cmd_map(unsigned type, unsigned val)
+{
+	return (type << S3C64XX_CMD_MAP_SHIFT) | val;
+}
+
+static unsigned int s3c6400_mem_addr(int fba, int fpa, int fsa)
+{
+	return (fba << S3C6400_FBA_SHIFT) | (fpa << S3C6400_FPA_SHIFT) |
+		(fsa << S3C6400_FSA_SHIFT);
+}
+
+static unsigned int s3c6410_mem_addr(int fba, int fpa, int fsa)
+{
+	return (fba << S3C6410_FBA_SHIFT) | (fpa << S3C6410_FPA_SHIFT) |
+		(fsa << S3C6410_FSA_SHIFT);
+}
+
+static void s3c_onenand_reset(void)
+{
+	unsigned long timeout = 0x10000;
+	int stat;
+
+	s3c_write_reg(ONENAND_MEM_RESET_COLD, MEM_RESET_OFFSET);
+	while (1 && timeout--) {
+		stat = s3c_read_reg(INT_ERR_STAT_OFFSET);
+		if (stat & RST_CMP)
+			break;
+	}
+	stat = s3c_read_reg(INT_ERR_STAT_OFFSET);
+	s3c_write_reg(stat, INT_ERR_ACK_OFFSET);
+
+	/* Clear interrupt */
+	s3c_write_reg(0x0, INT_ERR_ACK_OFFSET);
+	/* Clear the ECC status */
+	s3c_write_reg(0x0, ECC_ERR_STAT_OFFSET);
+}
+
+static unsigned short s3c_onenand_readw(void __iomem *addr)
+{
+	struct onenand_chip *this = onenand->mtd->priv;
+	struct device *dev = &onenand->pdev->dev;
+	int reg = addr - this->base;
+	int word_addr = reg >> 1;
+	int value;
+
+	/* It's used for probing time */
+	switch (reg) {
+	case ONENAND_REG_MANUFACTURER_ID:
+		return s3c_read_reg(MANUFACT_ID_OFFSET);
+	case ONENAND_REG_DEVICE_ID:
+		return s3c_read_reg(DEVICE_ID_OFFSET);
+	case ONENAND_REG_VERSION_ID:
+		return s3c_read_reg(FLASH_VER_ID_OFFSET);
+	case ONENAND_REG_DATA_BUFFER_SIZE:
+		return s3c_read_reg(DATA_BUF_SIZE_OFFSET);
+	case ONENAND_REG_TECHNOLOGY:
+		return s3c_read_reg(TECH_OFFSET);
+	case ONENAND_REG_SYS_CFG1:
+		return s3c_read_reg(MEM_CFG_OFFSET);
+
+	/* Used at unlock all status */
+	case ONENAND_REG_CTRL_STATUS:
+		return 0;
+
+	case ONENAND_REG_WP_STATUS:
+		return ONENAND_WP_US;
+
+	default:
+		break;
+	}
+
+	/* BootRAM access control */
+	if ((unsigned int) addr < ONENAND_DATARAM && onenand->bootram_command) {
+		if (word_addr == 0)
+			return s3c_read_reg(MANUFACT_ID_OFFSET);
+		if (word_addr == 1)
+			return s3c_read_reg(DEVICE_ID_OFFSET);
+		if (word_addr == 2)
+			return s3c_read_reg(FLASH_VER_ID_OFFSET);
+	}
+
+	value = s3c_read_cmd(CMD_MAP_11(onenand, word_addr)) & 0xffff;
+	dev_info(dev, "%s: Illegal access at reg 0x%x, value 0x%x\n", __func__,
+		 word_addr, value);
+	return value;
+}
+
+static void s3c_onenand_writew(unsigned short value, void __iomem *addr)
+{
+	struct onenand_chip *this = onenand->mtd->priv;
+	struct device *dev = &onenand->pdev->dev;
+	unsigned int reg = addr - this->base;
+	unsigned int word_addr = reg >> 1;
+
+	/* It's used for probing time */
+	switch (reg) {
+	case ONENAND_REG_SYS_CFG1:
+		s3c_write_reg(value, MEM_CFG_OFFSET);
+		return;
+
+	case ONENAND_REG_START_ADDRESS1:
+	case ONENAND_REG_START_ADDRESS2:
+		return;
+
+	/* Lock/lock-tight/unlock/unlock_all */
+	case ONENAND_REG_START_BLOCK_ADDRESS:
+		return;
+
+	default:
+		break;
+	}
+
+	/* BootRAM access control */
+	if ((unsigned int)addr < ONENAND_DATARAM) {
+		if (value == ONENAND_CMD_READID) {
+			onenand->bootram_command = 1;
+			return;
+		}
+		if (value == ONENAND_CMD_RESET) {
+			s3c_write_reg(ONENAND_MEM_RESET_COLD, MEM_RESET_OFFSET);
+			onenand->bootram_command = 0;
+			return;
+		}
+	}
+
+	dev_info(dev, "%s: Illegal access at reg 0x%x, value 0x%x\n", __func__,
+		 word_addr, value);
+
+	s3c_write_cmd(value, CMD_MAP_11(onenand, word_addr));
+}
+
+static int s3c_onenand_wait(struct mtd_info *mtd, int state)
+{
+	struct device *dev = &onenand->pdev->dev;
+	unsigned int flags = INT_ACT;
+	unsigned int stat, ecc;
+	unsigned long timeout;
+
+	switch (state) {
+	case FL_READING:
+		flags |= BLK_RW_CMP | LOAD_CMP;
+		break;
+	case FL_WRITING:
+		flags |= BLK_RW_CMP | PGM_CMP;
+		break;
+	case FL_ERASING:
+		flags |= BLK_RW_CMP | ERS_CMP;
+		break;
+	case FL_LOCKING:
+		flags |= BLK_RW_CMP;
+		break;
+	default:
+		break;
+	}
+
+	/* The 20 msec is enough */
+	timeout = jiffies + msecs_to_jiffies(20);
+	while (time_before(jiffies, timeout)) {
+		stat = s3c_read_reg(INT_ERR_STAT_OFFSET);
+		if (stat & flags)
+			break;
+
+		if (state != FL_READING)
+			cond_resched();
+	}
+	/* To get correct interrupt status in timeout case */
+	stat = s3c_read_reg(INT_ERR_STAT_OFFSET);
+	s3c_write_reg(stat, INT_ERR_ACK_OFFSET);
+
+	/*
+	 * In the Spec. it checks the controller status first
+	 * However if you get the correct information in case of
+	 * power off recovery (POR) test, it should read ECC status first
+	 */
+	if (stat & LOAD_CMP) {
+		ecc = s3c_read_reg(ECC_ERR_STAT_OFFSET);
+		if (ecc & ONENAND_ECC_4BIT_UNCORRECTABLE) {
+			dev_info(dev, "%s: ECC error = 0x%04x\n", __func__,
+				 ecc);
+			mtd->ecc_stats.failed++;
+			return -EBADMSG;
+		}
+	}
+
+	if (stat & (LOCKED_BLK | ERS_FAIL | PGM_FAIL | LD_FAIL_ECC_ERR)) {
+		dev_info(dev, "%s: controller error = 0x%04x\n", __func__,
+			 stat);
+		if (stat & LOCKED_BLK)
+			dev_info(dev, "%s: it's locked error = 0x%04x\n",
+				 __func__, stat);
+
+		return -EIO;
+	}
+
+	return 0;
+}
+
+static int s3c_onenand_command(struct mtd_info *mtd, int cmd, loff_t addr,
+			       size_t len)
+{
+	struct onenand_chip *this = mtd->priv;
+	unsigned int *m, *s;
+	int fba, fpa, fsa = 0;
+	unsigned int mem_addr, cmd_map_01, cmd_map_10;
+	int i, mcount, scount;
+	int index;
+
+	fba = (int) (addr >> this->erase_shift);
+	fpa = (int) (addr >> this->page_shift);
+	fpa &= this->page_mask;
+
+	mem_addr = onenand->mem_addr(fba, fpa, fsa);
+	cmd_map_01 = CMD_MAP_01(onenand, mem_addr);
+	cmd_map_10 = CMD_MAP_10(onenand, mem_addr);
+
+	switch (cmd) {
+	case ONENAND_CMD_READ:
+	case ONENAND_CMD_READOOB:
+	case ONENAND_CMD_BUFFERRAM:
+		ONENAND_SET_NEXT_BUFFERRAM(this);
+	default:
+		break;
+	}
+
+	index = ONENAND_CURRENT_BUFFERRAM(this);
+
+	/*
+	 * Emulate Two BufferRAMs and access with 4 bytes pointer
+	 */
+	m = onenand->page_buf;
+	s = onenand->oob_buf;
+
+	if (index) {
+		m += (this->writesize >> 2);
+		s += (mtd->oobsize >> 2);
+	}
+
+	mcount = mtd->writesize >> 2;
+	scount = mtd->oobsize >> 2;
+
+	switch (cmd) {
+	case ONENAND_CMD_READ:
+		/* Main */
+		for (i = 0; i < mcount; i++)
+			*m++ = s3c_read_cmd(cmd_map_01);
+		return 0;
+
+	case ONENAND_CMD_READOOB:
+		s3c_write_reg(TSRF, TRANS_SPARE_OFFSET);
+		/* Main */
+		for (i = 0; i < mcount; i++)
+			*m++ = s3c_read_cmd(cmd_map_01);
+
+		/* Spare */
+		for (i = 0; i < scount; i++)
+			*s++ = s3c_read_cmd(cmd_map_01);
+
+		s3c_write_reg(0, TRANS_SPARE_OFFSET);
+		return 0;
+
+	case ONENAND_CMD_PROG:
+		/* Main */
+		for (i = 0; i < mcount; i++)
+			s3c_write_cmd(*m++, cmd_map_01);
+		return 0;
+
+	case ONENAND_CMD_PROGOOB:
+		s3c_write_reg(TSRF, TRANS_SPARE_OFFSET);
+
+		/* Main - dummy write */
+		for (i = 0; i < mcount; i++)
+			s3c_write_cmd(0xffffffff, cmd_map_01);
+
+		/* Spare */
+		for (i = 0; i < scount; i++)
+			s3c_write_cmd(*s++, cmd_map_01);
+
+		s3c_write_reg(0, TRANS_SPARE_OFFSET);
+		return 0;
+
+	case ONENAND_CMD_UNLOCK_ALL:
+		s3c_write_cmd(ONENAND_UNLOCK_ALL, cmd_map_10);
+		return 0;
+
+	case ONENAND_CMD_ERASE:
+		s3c_write_cmd(ONENAND_ERASE_START, cmd_map_10);
+		return 0;
+
+	default:
+		break;
+	}
+
+	return 0;
+}
+
+static unsigned char *s3c_get_bufferram(struct mtd_info *mtd, int area)
+{
+	struct onenand_chip *this = mtd->priv;
+	int index = ONENAND_CURRENT_BUFFERRAM(this);
+	unsigned char *p;
+
+	if (area == ONENAND_DATARAM) {
+		p = onenand->page_buf;
+		if (index == 1)
+			p += this->writesize;
+	} else {
+		p = onenand->oob_buf;
+		if (index == 1)
+			p += mtd->oobsize;
+	}
+
+	return p;
+}
+
+static int onenand_read_bufferram(struct mtd_info *mtd, int area,
+				  unsigned char *buffer, int offset,
+				  size_t count)
+{
+	unsigned char *p;
+
+	p = s3c_get_bufferram(mtd, area);
+	memcpy(buffer, p + offset, count);
+	return 0;
+}
+
+static int onenand_write_bufferram(struct mtd_info *mtd, int area,
+				   const unsigned char *buffer, int offset,
+				   size_t count)
+{
+	unsigned char *p;
+
+	p = s3c_get_bufferram(mtd, area);
+	memcpy(p + offset, buffer, count);
+	return 0;
+}
+
+static int (*s5pc110_dma_ops)(dma_addr_t dst, dma_addr_t src, size_t count, int direction);
+
+static int s5pc110_dma_poll(dma_addr_t dst, dma_addr_t src, size_t count, int direction)
+{
+	void __iomem *base = onenand->dma_addr;
+	int status;
+	unsigned long timeout;
+
+	writel(src, base + S5PC110_DMA_SRC_ADDR);
+	writel(dst, base + S5PC110_DMA_DST_ADDR);
+
+	if (direction == S5PC110_DMA_DIR_READ) {
+		writel(S5PC110_DMA_SRC_CFG_READ, base + S5PC110_DMA_SRC_CFG);
+		writel(S5PC110_DMA_DST_CFG_READ, base + S5PC110_DMA_DST_CFG);
+	} else {
+		writel(S5PC110_DMA_SRC_CFG_WRITE, base + S5PC110_DMA_SRC_CFG);
+		writel(S5PC110_DMA_DST_CFG_WRITE, base + S5PC110_DMA_DST_CFG);
+	}
+
+	writel(count, base + S5PC110_DMA_TRANS_SIZE);
+	writel(direction, base + S5PC110_DMA_TRANS_DIR);
+
+	writel(S5PC110_DMA_TRANS_CMD_TR, base + S5PC110_DMA_TRANS_CMD);
+
+	/*
+	 * There's no exact timeout values at Spec.
+	 * In real case it takes under 1 msec.
+	 * So 20 msecs are enough.
+	 */
+	timeout = jiffies + msecs_to_jiffies(20);
+
+	do {
+		status = readl(base + S5PC110_DMA_TRANS_STATUS);
+		if (status & S5PC110_DMA_TRANS_STATUS_TE) {
+			writel(S5PC110_DMA_TRANS_CMD_TEC,
+					base + S5PC110_DMA_TRANS_CMD);
+			return -EIO;
+		}
+	} while (!(status & S5PC110_DMA_TRANS_STATUS_TD) &&
+		time_before(jiffies, timeout));
+
+	writel(S5PC110_DMA_TRANS_CMD_TDC, base + S5PC110_DMA_TRANS_CMD);
+
+	return 0;
+}
+
+static irqreturn_t s5pc110_onenand_irq(int irq, void *data)
+{
+	void __iomem *base = onenand->dma_addr;
+	int status, cmd = 0;
+
+	status = readl(base + S5PC110_INTC_DMA_STATUS);
+
+	if (likely(status & S5PC110_INTC_DMA_TD))
+		cmd = S5PC110_DMA_TRANS_CMD_TDC;
+
+	if (unlikely(status & S5PC110_INTC_DMA_TE))
+		cmd = S5PC110_DMA_TRANS_CMD_TEC;
+
+	writel(cmd, base + S5PC110_DMA_TRANS_CMD);
+	writel(status, base + S5PC110_INTC_DMA_CLR);
+
+	if (!onenand->complete.done)
+		complete(&onenand->complete);
+
+	return IRQ_HANDLED;
+}
+
+static int s5pc110_dma_irq(dma_addr_t dst, dma_addr_t src, size_t count, int direction)
+{
+	void __iomem *base = onenand->dma_addr;
+	int status;
+
+	status = readl(base + S5PC110_INTC_DMA_MASK);
+	if (status) {
+		status &= ~(S5PC110_INTC_DMA_TD | S5PC110_INTC_DMA_TE);
+		writel(status, base + S5PC110_INTC_DMA_MASK);
+	}
+
+	writel(src, base + S5PC110_DMA_SRC_ADDR);
+	writel(dst, base + S5PC110_DMA_DST_ADDR);
+
+	if (direction == S5PC110_DMA_DIR_READ) {
+		writel(S5PC110_DMA_SRC_CFG_READ, base + S5PC110_DMA_SRC_CFG);
+		writel(S5PC110_DMA_DST_CFG_READ, base + S5PC110_DMA_DST_CFG);
+	} else {
+		writel(S5PC110_DMA_SRC_CFG_WRITE, base + S5PC110_DMA_SRC_CFG);
+		writel(S5PC110_DMA_DST_CFG_WRITE, base + S5PC110_DMA_DST_CFG);
+	}
+
+	writel(count, base + S5PC110_DMA_TRANS_SIZE);
+	writel(direction, base + S5PC110_DMA_TRANS_DIR);
+
+	writel(S5PC110_DMA_TRANS_CMD_TR, base + S5PC110_DMA_TRANS_CMD);
+
+	wait_for_completion_timeout(&onenand->complete, msecs_to_jiffies(20));
+
+	return 0;
+}
+
+static int s5pc110_read_bufferram(struct mtd_info *mtd, int area,
+		unsigned char *buffer, int offset, size_t count)
+{
+	struct onenand_chip *this = mtd->priv;
+	void __iomem *p;
+	void *buf = (void *) buffer;
+	dma_addr_t dma_src, dma_dst;
+	int err, ofs, page_dma = 0;
+	struct device *dev = &onenand->pdev->dev;
+
+	p = this->base + area;
+	if (ONENAND_CURRENT_BUFFERRAM(this)) {
+		if (area == ONENAND_DATARAM)
+			p += this->writesize;
+		else
+			p += mtd->oobsize;
+	}
+
+	if (offset & 3 || (size_t) buf & 3 ||
+		!onenand->dma_addr || count != mtd->writesize)
+		goto normal;
+
+	/* Handle vmalloc address */
+	if (buf >= high_memory) {
+		struct page *page;
+
+		if (((size_t) buf & PAGE_MASK) !=
+		    ((size_t) (buf + count - 1) & PAGE_MASK))
+			goto normal;
+		page = vmalloc_to_page(buf);
+		if (!page)
+			goto normal;
+
+		/* Page offset */
+		ofs = ((size_t) buf & ~PAGE_MASK);
+		page_dma = 1;
+
+		/* DMA routine */
+		dma_src = onenand->phys_base + (p - this->base);
+		dma_dst = dma_map_page(dev, page, ofs, count, DMA_FROM_DEVICE);
+	} else {
+		/* DMA routine */
+		dma_src = onenand->phys_base + (p - this->base);
+		dma_dst = dma_map_single(dev, buf, count, DMA_FROM_DEVICE);
+	}
+	if (dma_mapping_error(dev, dma_dst)) {
+		dev_err(dev, "Couldn't map a %d byte buffer for DMA\n", count);
+		goto normal;
+	}
+	err = s5pc110_dma_ops(dma_dst, dma_src,
+			count, S5PC110_DMA_DIR_READ);
+
+	if (page_dma)
+		dma_unmap_page(dev, dma_dst, count, DMA_FROM_DEVICE);
+	else
+		dma_unmap_single(dev, dma_dst, count, DMA_FROM_DEVICE);
+
+	if (!err)
+		return 0;
+
+normal:
+	if (count != mtd->writesize) {
+		/* Copy the bufferram to memory to prevent unaligned access */
+		memcpy(this->page_buf, p, mtd->writesize);
+		p = this->page_buf + offset;
+	}
+
+	memcpy(buffer, p, count);
+
+	return 0;
+}
+
+static int s5pc110_chip_probe(struct mtd_info *mtd)
+{
+	/* Now just return 0 */
+	return 0;
+}
+
+static int s3c_onenand_bbt_wait(struct mtd_info *mtd, int state)
+{
+	unsigned int flags = INT_ACT | LOAD_CMP;
+	unsigned int stat;
+	unsigned long timeout;
+
+	/* The 20 msec is enough */
+	timeout = jiffies + msecs_to_jiffies(20);
+	while (time_before(jiffies, timeout)) {
+		stat = s3c_read_reg(INT_ERR_STAT_OFFSET);
+		if (stat & flags)
+			break;
+	}
+	/* To get correct interrupt status in timeout case */
+	stat = s3c_read_reg(INT_ERR_STAT_OFFSET);
+	s3c_write_reg(stat, INT_ERR_ACK_OFFSET);
+
+	if (stat & LD_FAIL_ECC_ERR) {
+		s3c_onenand_reset();
+		return ONENAND_BBT_READ_ERROR;
+	}
+
+	if (stat & LOAD_CMP) {
+		int ecc = s3c_read_reg(ECC_ERR_STAT_OFFSET);
+		if (ecc & ONENAND_ECC_4BIT_UNCORRECTABLE) {
+			s3c_onenand_reset();
+			return ONENAND_BBT_READ_ERROR;
+		}
+	}
+
+	return 0;
+}
+
+static void s3c_onenand_check_lock_status(struct mtd_info *mtd)
+{
+	struct onenand_chip *this = mtd->priv;
+	struct device *dev = &onenand->pdev->dev;
+	unsigned int block, end;
+	int tmp;
+
+	end = this->chipsize >> this->erase_shift;
+
+	for (block = 0; block < end; block++) {
+		unsigned int mem_addr = onenand->mem_addr(block, 0, 0);
+		tmp = s3c_read_cmd(CMD_MAP_01(onenand, mem_addr));
+
+		if (s3c_read_reg(INT_ERR_STAT_OFFSET) & LOCKED_BLK) {
+			dev_err(dev, "block %d is write-protected!\n", block);
+			s3c_write_reg(LOCKED_BLK, INT_ERR_ACK_OFFSET);
+		}
+	}
+}
+
+static void s3c_onenand_do_lock_cmd(struct mtd_info *mtd, loff_t ofs,
+				    size_t len, int cmd)
+{
+	struct onenand_chip *this = mtd->priv;
+	int start, end, start_mem_addr, end_mem_addr;
+
+	start = ofs >> this->erase_shift;
+	start_mem_addr = onenand->mem_addr(start, 0, 0);
+	end = start + (len >> this->erase_shift) - 1;
+	end_mem_addr = onenand->mem_addr(end, 0, 0);
+
+	if (cmd == ONENAND_CMD_LOCK) {
+		s3c_write_cmd(ONENAND_LOCK_START, CMD_MAP_10(onenand,
+							     start_mem_addr));
+		s3c_write_cmd(ONENAND_LOCK_END, CMD_MAP_10(onenand,
+							   end_mem_addr));
+	} else {
+		s3c_write_cmd(ONENAND_UNLOCK_START, CMD_MAP_10(onenand,
+							       start_mem_addr));
+		s3c_write_cmd(ONENAND_UNLOCK_END, CMD_MAP_10(onenand,
+							     end_mem_addr));
+	}
+
+	this->wait(mtd, FL_LOCKING);
+}
+
+static void s3c_unlock_all(struct mtd_info *mtd)
+{
+	struct onenand_chip *this = mtd->priv;
+	loff_t ofs = 0;
+	size_t len = this->chipsize;
+
+	if (this->options & ONENAND_HAS_UNLOCK_ALL) {
+		/* Write unlock command */
+		this->command(mtd, ONENAND_CMD_UNLOCK_ALL, 0, 0);
+
+		/* No need to check return value */
+		this->wait(mtd, FL_LOCKING);
+
+		/* Workaround for all block unlock in DDP */
+		if (!ONENAND_IS_DDP(this)) {
+			s3c_onenand_check_lock_status(mtd);
+			return;
+		}
+
+		/* All blocks on another chip */
+		ofs = this->chipsize >> 1;
+		len = this->chipsize >> 1;
+	}
+
+	s3c_onenand_do_lock_cmd(mtd, ofs, len, ONENAND_CMD_UNLOCK);
+
+	s3c_onenand_check_lock_status(mtd);
+}
+
+static void s3c_onenand_setup(struct mtd_info *mtd)
+{
+	struct onenand_chip *this = mtd->priv;
+
+	onenand->mtd = mtd;
+
+	if (onenand->type == TYPE_S3C6400) {
+		onenand->mem_addr = s3c6400_mem_addr;
+		onenand->cmd_map = s3c64xx_cmd_map;
+	} else if (onenand->type == TYPE_S3C6410) {
+		onenand->mem_addr = s3c6410_mem_addr;
+		onenand->cmd_map = s3c64xx_cmd_map;
+	} else if (onenand->type == TYPE_S5PC110) {
+		/* Use generic onenand functions */
+		this->read_bufferram = s5pc110_read_bufferram;
+		this->chip_probe = s5pc110_chip_probe;
+		return;
+	} else {
+		BUG();
+	}
+
+	this->read_word = s3c_onenand_readw;
+	this->write_word = s3c_onenand_writew;
+
+	this->wait = s3c_onenand_wait;
+	this->bbt_wait = s3c_onenand_bbt_wait;
+	this->unlock_all = s3c_unlock_all;
+	this->command = s3c_onenand_command;
+
+	this->read_bufferram = onenand_read_bufferram;
+	this->write_bufferram = onenand_write_bufferram;
+}
+
+static int s3c_onenand_probe(struct platform_device *pdev)
+{
+	struct onenand_platform_data *pdata;
+	struct onenand_chip *this;
+	struct mtd_info *mtd;
+	struct resource *r;
+	int size, err;
+
+	pdata = dev_get_platdata(&pdev->dev);
+	/* No need to check pdata. the platform data is optional */
+
+	size = sizeof(struct mtd_info) + sizeof(struct onenand_chip);
+	mtd = devm_kzalloc(&pdev->dev, size, GFP_KERNEL);
+	if (!mtd)
+		return -ENOMEM;
+
+	onenand = devm_kzalloc(&pdev->dev, sizeof(struct s3c_onenand),
+			       GFP_KERNEL);
+	if (!onenand)
+		return -ENOMEM;
+
+	this = (struct onenand_chip *) &mtd[1];
+	mtd->priv = this;
+	mtd->dev.parent = &pdev->dev;
+	onenand->pdev = pdev;
+	onenand->type = platform_get_device_id(pdev)->driver_data;
+
+	s3c_onenand_setup(mtd);
+
+	r = platform_get_resource(pdev, IORESOURCE_MEM, 0);
+	onenand->base = devm_ioremap_resource(&pdev->dev, r);
+	if (IS_ERR(onenand->base))
+		return PTR_ERR(onenand->base);
+
+	onenand->phys_base = r->start;
+
+	/* Set onenand_chip also */
+	this->base = onenand->base;
+
+	/* Use runtime badblock check */
+	this->options |= ONENAND_SKIP_UNLOCK_CHECK;
+
+	if (onenand->type != TYPE_S5PC110) {
+		r = platform_get_resource(pdev, IORESOURCE_MEM, 1);
+		onenand->ahb_addr = devm_ioremap_resource(&pdev->dev, r);
+		if (IS_ERR(onenand->ahb_addr))
+			return PTR_ERR(onenand->ahb_addr);
+
+		/* Allocate 4KiB BufferRAM */
+		onenand->page_buf = devm_kzalloc(&pdev->dev, SZ_4K,
+						 GFP_KERNEL);
+		if (!onenand->page_buf)
+			return -ENOMEM;
+
+		/* Allocate 128 SpareRAM */
+		onenand->oob_buf = devm_kzalloc(&pdev->dev, 128, GFP_KERNEL);
+		if (!onenand->oob_buf)
+			return -ENOMEM;
+
+		/* S3C doesn't handle subpage write */
+		mtd->subpage_sft = 0;
+		this->subpagesize = mtd->writesize;
+
+	} else { /* S5PC110 */
+		r = platform_get_resource(pdev, IORESOURCE_MEM, 1);
+		onenand->dma_addr = devm_ioremap_resource(&pdev->dev, r);
+		if (IS_ERR(onenand->dma_addr))
+			return PTR_ERR(onenand->dma_addr);
+
+		s5pc110_dma_ops = s5pc110_dma_poll;
+		/* Interrupt support */
+		r = platform_get_resource(pdev, IORESOURCE_IRQ, 0);
+		if (r) {
+			init_completion(&onenand->complete);
+			s5pc110_dma_ops = s5pc110_dma_irq;
+			err = devm_request_irq(&pdev->dev, r->start,
+					       s5pc110_onenand_irq,
+					       IRQF_SHARED, "onenand",
+					       &onenand);
+			if (err) {
+				dev_err(&pdev->dev, "failed to get irq\n");
+				return err;
+			}
+		}
+	}
+
+	err = onenand_scan(mtd, 1);
+	if (err)
+		return err;
+
+	if (onenand->type != TYPE_S5PC110) {
+		/* S3C doesn't handle subpage write */
+		mtd->subpage_sft = 0;
+		this->subpagesize = mtd->writesize;
+	}
+
+	if (s3c_read_reg(MEM_CFG_OFFSET) & ONENAND_SYS_CFG1_SYNC_READ)
+		dev_info(&onenand->pdev->dev, "OneNAND Sync. Burst Read enabled\n");
+
+	err = mtd_device_parse_register(mtd, NULL, NULL,
+					pdata ? pdata->parts : NULL,
+					pdata ? pdata->nr_parts : 0);
+	if (err) {
+		dev_err(&pdev->dev, "failed to parse partitions and register the MTD device\n");
+		onenand_release(mtd);
+		return err;
+	}
+
+	platform_set_drvdata(pdev, mtd);
+
+	return 0;
+}
+
+static int s3c_onenand_remove(struct platform_device *pdev)
+{
+	struct mtd_info *mtd = platform_get_drvdata(pdev);
+
+	onenand_release(mtd);
+
+	return 0;
+}
+
+static int s3c_pm_ops_suspend(struct device *dev)
+{
+	struct platform_device *pdev = to_platform_device(dev);
+	struct mtd_info *mtd = platform_get_drvdata(pdev);
+	struct onenand_chip *this = mtd->priv;
+
+	this->wait(mtd, FL_PM_SUSPENDED);
+	return 0;
+}
+
+static  int s3c_pm_ops_resume(struct device *dev)
+{
+	struct platform_device *pdev = to_platform_device(dev);
+	struct mtd_info *mtd = platform_get_drvdata(pdev);
+	struct onenand_chip *this = mtd->priv;
+
+	this->unlock_all(mtd);
+	return 0;
+}
+
+static const struct dev_pm_ops s3c_pm_ops = {
+	.suspend	= s3c_pm_ops_suspend,
+	.resume		= s3c_pm_ops_resume,
+};
+
+static const struct platform_device_id s3c_onenand_driver_ids[] = {
+	{
+		.name		= "s3c6400-onenand",
+		.driver_data	= TYPE_S3C6400,
+	}, {
+		.name		= "s3c6410-onenand",
+		.driver_data	= TYPE_S3C6410,
+	}, {
+		.name		= "s5pc110-onenand",
+		.driver_data	= TYPE_S5PC110,
+	}, { },
+};
+MODULE_DEVICE_TABLE(platform, s3c_onenand_driver_ids);
+
+static struct platform_driver s3c_onenand_driver = {
+	.driver         = {
+		.name	= "samsung-onenand",
+		.pm	= &s3c_pm_ops,
+	},
+	.id_table	= s3c_onenand_driver_ids,
+	.probe          = s3c_onenand_probe,
+	.remove         = s3c_onenand_remove,
+};
+
+module_platform_driver(s3c_onenand_driver);
+
+MODULE_LICENSE("GPL");
+MODULE_AUTHOR("Kyungmin Park <kyungmin.park@samsung.com>");
+MODULE_DESCRIPTION("Samsung OneNAND controller support");
diff --git a/drivers/mtd/nand/onenand/samsung.h b/drivers/mtd/nand/onenand/samsung.h
new file mode 100644
index 000000000000..9016dc0136a8
--- /dev/null
+++ b/drivers/mtd/nand/onenand/samsung.h
@@ -0,0 +1,59 @@
+/*
+ *  Copyright (C) 2008-2010 Samsung Electronics
+ *  Kyungmin Park <kyungmin.park@samsung.com>
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License version 2 as
+ * published by the Free Software Foundation.
+ */
+#ifndef __SAMSUNG_ONENAND_H__
+#define __SAMSUNG_ONENAND_H__
+
+/*
+ * OneNAND Controller
+ */
+#define MEM_CFG_OFFSET		0x0000
+#define BURST_LEN_OFFSET	0x0010
+#define MEM_RESET_OFFSET	0x0020
+#define INT_ERR_STAT_OFFSET	0x0030
+#define INT_ERR_MASK_OFFSET	0x0040
+#define INT_ERR_ACK_OFFSET	0x0050
+#define ECC_ERR_STAT_OFFSET	0x0060
+#define MANUFACT_ID_OFFSET	0x0070
+#define DEVICE_ID_OFFSET	0x0080
+#define DATA_BUF_SIZE_OFFSET	0x0090
+#define BOOT_BUF_SIZE_OFFSET	0x00A0
+#define BUF_AMOUNT_OFFSET	0x00B0
+#define TECH_OFFSET		0x00C0
+#define FBA_WIDTH_OFFSET	0x00D0
+#define FPA_WIDTH_OFFSET	0x00E0
+#define FSA_WIDTH_OFFSET	0x00F0
+#define TRANS_SPARE_OFFSET	0x0140
+#define DBS_DFS_WIDTH_OFFSET	0x0160
+#define INT_PIN_ENABLE_OFFSET	0x01A0
+#define ACC_CLOCK_OFFSET	0x01C0
+#define FLASH_VER_ID_OFFSET	0x01F0
+#define FLASH_AUX_CNTRL_OFFSET	0x0300		/* s3c64xx only */
+
+#define ONENAND_MEM_RESET_HOT	0x3
+#define ONENAND_MEM_RESET_COLD	0x2
+#define ONENAND_MEM_RESET_WARM	0x1
+
+#define CACHE_OP_ERR		(1 << 13)
+#define RST_CMP			(1 << 12)
+#define RDY_ACT			(1 << 11)
+#define INT_ACT			(1 << 10)
+#define UNSUP_CMD		(1 << 9)
+#define LOCKED_BLK		(1 << 8)
+#define BLK_RW_CMP		(1 << 7)
+#define ERS_CMP			(1 << 6)
+#define PGM_CMP			(1 << 5)
+#define LOAD_CMP		(1 << 4)
+#define ERS_FAIL		(1 << 3)
+#define PGM_FAIL		(1 << 2)
+#define INT_TO			(1 << 1)
+#define LD_FAIL_ECC_ERR		(1 << 0)
+
+#define TSRF			(1 << 0)
+
+#endif
diff --git a/drivers/mtd/nand/raw/Kconfig b/drivers/mtd/nand/raw/Kconfig
new file mode 100644
index 000000000000..19a2b283fbbe
--- /dev/null
+++ b/drivers/mtd/nand/raw/Kconfig
@@ -0,0 +1,537 @@
+config MTD_NAND_ECC
+	tristate
+
+config MTD_NAND_ECC_SMC
+	bool "NAND ECC Smart Media byte order"
+	depends on MTD_NAND_ECC
+	default n
+	help
+	  Software ECC according to the Smart Media Specification.
+	  The original Linux implementation had byte 0 and 1 swapped.
+
+
+menuconfig MTD_NAND
+	tristate "Raw/Parallel NAND Device Support"
+	depends on MTD
+	select MTD_NAND_ECC
+	help
+	  This enables support for accessing all type of raw/parallel
+	  NAND flash devices. For further information see
+	  <http://www.linux-mtd.infradead.org/doc/nand.html>.
+
+if MTD_NAND
+
+config MTD_NAND_BCH
+	tristate
+	select BCH
+	depends on MTD_NAND_ECC_BCH
+	default MTD_NAND
+
+config MTD_NAND_ECC_BCH
+	bool "Support software BCH ECC"
+	default n
+	help
+	  This enables support for software BCH error correction. Binary BCH
+	  codes are more powerful and cpu intensive than traditional Hamming
+	  ECC codes. They are used with NAND devices requiring more than 1 bit
+	  of error correction.
+
+config MTD_SM_COMMON
+	tristate
+	default n
+
+config MTD_NAND_DENALI
+	tristate
+
+config MTD_NAND_DENALI_PCI
+        tristate "Support Denali NAND controller on Intel Moorestown"
+	select MTD_NAND_DENALI
+	depends on HAS_DMA && PCI
+        help
+          Enable the driver for NAND flash on Intel Moorestown, using the
+          Denali NAND controller core.
+
+config MTD_NAND_DENALI_DT
+	tristate "Support Denali NAND controller as a DT device"
+	select MTD_NAND_DENALI
+	depends on HAS_DMA && HAVE_CLK && OF
+	help
+	  Enable the driver for NAND flash on platforms using a Denali NAND
+	  controller as a DT device.
+
+config MTD_NAND_GPIO
+	tristate "GPIO assisted NAND Flash driver"
+	depends on GPIOLIB || COMPILE_TEST
+	depends on HAS_IOMEM
+	help
+	  This enables a NAND flash driver where control signals are
+	  connected to GPIO pins, and commands and data are communicated
+	  via a memory mapped interface.
+
+config MTD_NAND_AMS_DELTA
+	tristate "NAND Flash device on Amstrad E3"
+	depends on MACH_AMS_DELTA
+	default y
+	help
+	  Support for NAND flash on Amstrad E3 (Delta).
+
+config MTD_NAND_OMAP2
+	tristate "NAND Flash device on OMAP2, OMAP3, OMAP4 and Keystone"
+	depends on (ARCH_OMAP2PLUS || ARCH_KEYSTONE)
+	help
+          Support for NAND flash on Texas Instruments OMAP2, OMAP3, OMAP4
+	  and Keystone platforms.
+
+config MTD_NAND_OMAP_BCH
+	depends on MTD_NAND_OMAP2
+	bool "Support hardware based BCH error correction"
+	default n
+	select BCH
+	help
+	  This config enables the ELM hardware engine, which can be used to
+	  locate and correct errors when using BCH ECC scheme. This offloads
+	  the cpu from doing ECC error searching and correction. However some
+	  legacy OMAP families like OMAP2xxx, OMAP3xxx do not have ELM engine
+	  so this is optional for them.
+
+config MTD_NAND_OMAP_BCH_BUILD
+	def_tristate MTD_NAND_OMAP2 && MTD_NAND_OMAP_BCH
+
+config MTD_NAND_RICOH
+	tristate "Ricoh xD card reader"
+	default n
+	depends on PCI
+	select MTD_SM_COMMON
+	help
+	  Enable support for Ricoh R5C852 xD card reader
+	  You also need to enable ether
+	  NAND SSFDC (SmartMedia) read only translation layer' or new
+	  expermental, readwrite
+	  'SmartMedia/xD new translation layer'
+
+config MTD_NAND_AU1550
+	tristate "Au1550/1200 NAND support"
+	depends on MIPS_ALCHEMY
+	help
+	  This enables the driver for the NAND flash controller on the
+	  AMD/Alchemy 1550 SOC.
+
+config MTD_NAND_S3C2410
+	tristate "NAND Flash support for Samsung S3C SoCs"
+	depends on ARCH_S3C24XX || ARCH_S3C64XX
+	help
+	  This enables the NAND flash controller on the S3C24xx and S3C64xx
+	  SoCs
+
+	  No board specific support is done by this driver, each board
+	  must advertise a platform_device for the driver to attach.
+
+config MTD_NAND_S3C2410_DEBUG
+	bool "Samsung S3C NAND driver debug"
+	depends on MTD_NAND_S3C2410
+	help
+	  Enable debugging of the S3C NAND driver
+
+config MTD_NAND_NDFC
+	tristate "NDFC NanD Flash Controller"
+	depends on 4xx
+	select MTD_NAND_ECC_SMC
+	help
+	 NDFC Nand Flash Controllers are integrated in IBM/AMCC's 4xx SoCs
+
+config MTD_NAND_S3C2410_CLKSTOP
+	bool "Samsung S3C NAND IDLE clock stop"
+	depends on MTD_NAND_S3C2410
+	default n
+	help
+	  Stop the clock to the NAND controller when there is no chip
+	  selected to save power. This will mean there is a small delay
+	  when the is NAND chip selected or released, but will save
+	  approximately 5mA of power when there is nothing happening.
+
+config MTD_NAND_TANGO
+	tristate "NAND Flash support for Tango chips"
+	depends on ARCH_TANGO || COMPILE_TEST
+	depends on HAS_DMA
+	help
+	  Enables the NAND Flash controller on Tango chips.
+
+config MTD_NAND_DISKONCHIP
+	tristate "DiskOnChip 2000, Millennium and Millennium Plus (NAND reimplementation)"
+	depends on HAS_IOMEM
+	select REED_SOLOMON
+	select REED_SOLOMON_DEC16
+	help
+	  This is a reimplementation of M-Systems DiskOnChip 2000,
+	  Millennium and Millennium Plus as a standard NAND device driver,
+	  as opposed to the earlier self-contained MTD device drivers.
+	  This should enable, among other things, proper JFFS2 operation on
+	  these devices.
+
+config MTD_NAND_DISKONCHIP_PROBE_ADVANCED
+        bool "Advanced detection options for DiskOnChip"
+        depends on MTD_NAND_DISKONCHIP
+        help
+          This option allows you to specify nonstandard address at which to
+          probe for a DiskOnChip, or to change the detection options.  You
+          are unlikely to need any of this unless you are using LinuxBIOS.
+          Say 'N'.
+
+config MTD_NAND_DISKONCHIP_PROBE_ADDRESS
+        hex "Physical address of DiskOnChip" if MTD_NAND_DISKONCHIP_PROBE_ADVANCED
+        depends on MTD_NAND_DISKONCHIP
+        default "0"
+        ---help---
+        By default, the probe for DiskOnChip devices will look for a
+        DiskOnChip at every multiple of 0x2000 between 0xC8000 and 0xEE000.
+        This option allows you to specify a single address at which to probe
+        for the device, which is useful if you have other devices in that
+        range which get upset when they are probed.
+
+        (Note that on PowerPC, the normal probe will only check at
+        0xE4000000.)
+
+        Normally, you should leave this set to zero, to allow the probe at
+        the normal addresses.
+
+config MTD_NAND_DISKONCHIP_PROBE_HIGH
+        bool "Probe high addresses"
+        depends on MTD_NAND_DISKONCHIP_PROBE_ADVANCED
+        help
+          By default, the probe for DiskOnChip devices will look for a
+          DiskOnChip at every multiple of 0x2000 between 0xC8000 and 0xEE000.
+          This option changes to make it probe between 0xFFFC8000 and
+          0xFFFEE000.  Unless you are using LinuxBIOS, this is unlikely to be
+          useful to you.  Say 'N'.
+
+config MTD_NAND_DISKONCHIP_BBTWRITE
+	bool "Allow BBT writes on DiskOnChip Millennium and 2000TSOP"
+	depends on MTD_NAND_DISKONCHIP
+	help
+	  On DiskOnChip devices shipped with the INFTL filesystem (Millennium
+	  and 2000 TSOP/Alon), Linux reserves some space at the end of the
+	  device for the Bad Block Table (BBT).  If you have existing INFTL
+	  data on your device (created by non-Linux tools such as M-Systems'
+	  DOS drivers), your data might overlap the area Linux wants to use for
+	  the BBT.  If this is a concern for you, leave this option disabled and
+	  Linux will not write BBT data into this area.
+	  The downside of leaving this option disabled is that if bad blocks
+	  are detected by Linux, they will not be recorded in the BBT, which
+	  could cause future problems.
+	  Once you enable this option, new filesystems (INFTL or others, created
+	  in Linux or other operating systems) will not use the reserved area.
+	  The only reason not to enable this option is to prevent damage to
+	  preexisting filesystems.
+	  Even if you leave this disabled, you can enable BBT writes at module
+	  load time (assuming you build diskonchip as a module) with the module
+	  parameter "inftl_bbt_write=1".
+
+config MTD_NAND_DOCG4
+	tristate "Support for DiskOnChip G4"
+	depends on HAS_IOMEM
+	select BCH
+	select BITREVERSE
+	help
+	  Support for diskonchip G4 nand flash, found in various smartphones and
+	  PDAs, among them the Palm Treo680, HTC Prophet and Wizard, Toshiba
+	  Portege G900, Asus P526, and O2 XDA Zinc.
+
+	  With this driver you will be able to use UBI and create a ubifs on the
+	  device, so you may wish to consider enabling UBI and UBIFS as well.
+
+	  These devices ship with the Mys/Sandisk SAFTL formatting, for which
+	  there is currently no mtd parser, so you may want to use command line
+	  partitioning to segregate write-protected blocks. On the Treo680, the
+	  first five erase blocks (256KiB each) are write-protected, followed
+	  by the block containing the saftl partition table.  This is probably
+	  typical.
+
+config MTD_NAND_SHARPSL
+	tristate "Support for NAND Flash on Sharp SL Series (C7xx + others)"
+	depends on ARCH_PXA
+
+config MTD_NAND_CAFE
+	tristate "NAND support for OLPC CAFÉ chip"
+	depends on PCI
+	select REED_SOLOMON
+	select REED_SOLOMON_DEC16
+	help
+	  Use NAND flash attached to the CAFÉ chip designed for the OLPC
+	  laptop.
+
+config MTD_NAND_CS553X
+	tristate "NAND support for CS5535/CS5536 (AMD Geode companion chip)"
+	depends on X86_32
+	depends on !UML && HAS_IOMEM
+	help
+	  The CS553x companion chips for the AMD Geode processor
+	  include NAND flash controllers with built-in hardware ECC
+	  capabilities; enabling this option will allow you to use
+	  these. The driver will check the MSRs to verify that the
+	  controller is enabled for NAND, and currently requires that
+	  the controller be in MMIO mode.
+
+	  If you say "m", the module will be called cs553x_nand.
+
+config MTD_NAND_ATMEL
+	tristate "Support for NAND Flash / SmartMedia on AT91"
+	depends on ARCH_AT91
+	select MFD_ATMEL_SMC
+	help
+	  Enables support for NAND Flash / Smart Media Card interface
+	  on Atmel AT91 processors.
+
+config MTD_NAND_MARVELL
+	tristate "NAND controller support on Marvell boards"
+	depends on PXA3xx || ARCH_MMP || PLAT_ORION || ARCH_MVEBU || \
+		   COMPILE_TEST
+	depends on HAS_IOMEM && HAS_DMA
+	help
+	  This enables the NAND flash controller driver for Marvell boards,
+	  including:
+	  - PXA3xx processors (NFCv1)
+	  - 32-bit Armada platforms (XP, 37x, 38x, 39x) (NFCv2)
+	  - 64-bit Aramda platforms (7k, 8k) (NFCv2)
+
+config MTD_NAND_SLC_LPC32XX
+	tristate "NXP LPC32xx SLC Controller"
+	depends on ARCH_LPC32XX
+	help
+	  Enables support for NXP's LPC32XX SLC (i.e. for Single Level Cell
+	  chips) NAND controller. This is the default for the PHYTEC 3250
+	  reference board which contains a NAND256R3A2CZA6 chip.
+
+	  Please check the actual NAND chip connected and its support
+	  by the SLC NAND controller.
+
+config MTD_NAND_MLC_LPC32XX
+	tristate "NXP LPC32xx MLC Controller"
+	depends on ARCH_LPC32XX
+	help
+	  Uses the LPC32XX MLC (i.e. for Multi Level Cell chips) NAND
+	  controller. This is the default for the WORK92105 controller
+	  board.
+
+	  Please check the actual NAND chip connected and its support
+	  by the MLC NAND controller.
+
+config MTD_NAND_CM_X270
+	tristate "Support for NAND Flash on CM-X270 modules"
+	depends on MACH_ARMCORE
+
+config MTD_NAND_PASEMI
+	tristate "NAND support for PA Semi PWRficient"
+	depends on PPC_PASEMI
+	help
+	  Enables support for NAND Flash interface on PA Semi PWRficient
+	  based boards
+
+config MTD_NAND_TMIO
+	tristate "NAND Flash device on Toshiba Mobile IO Controller"
+	depends on MFD_TMIO
+	help
+	  Support for NAND flash connected to a Toshiba Mobile IO
+	  Controller in some PDAs, including the Sharp SL6000x.
+
+config MTD_NAND_NANDSIM
+	tristate "Support for NAND Flash Simulator"
+	help
+	  The simulator may simulate various NAND flash chips for the
+	  MTD nand layer.
+
+config MTD_NAND_GPMI_NAND
+        tristate "GPMI NAND Flash Controller driver"
+        depends on MTD_NAND && MXS_DMA
+        help
+	 Enables NAND Flash support for IMX23, IMX28 or IMX6.
+	 The GPMI controller is very powerful, with the help of BCH
+	 module, it can do the hardware ECC. The GPMI supports several
+	 NAND flashs at the same time.
+
+config MTD_NAND_BRCMNAND
+	tristate "Broadcom STB NAND controller"
+	depends on ARM || ARM64 || MIPS
+	help
+	  Enables the Broadcom NAND controller driver. The controller was
+	  originally designed for Set-Top Box but is used on various BCM7xxx,
+	  BCM3xxx, BCM63xxx, iProc/Cygnus and more.
+
+config MTD_NAND_BCM47XXNFLASH
+	tristate "Support for NAND flash on BCM4706 BCMA bus"
+	depends on BCMA_NFLASH
+	help
+	  BCMA bus can have various flash memories attached, they are
+	  registered by bcma as platform devices. This enables driver for
+	  NAND flash memories. For now only BCM4706 is supported.
+
+config MTD_NAND_PLATFORM
+	tristate "Support for generic platform NAND driver"
+	depends on HAS_IOMEM
+	help
+	  This implements a generic NAND driver for on-SOC platform
+	  devices. You will need to provide platform-specific functions
+	  via platform_data.
+
+config MTD_NAND_ORION
+	tristate "NAND Flash support for Marvell Orion SoC"
+	depends on PLAT_ORION
+	help
+	  This enables the NAND flash controller on Orion machines.
+
+	  No board specific support is done by this driver, each board
+	  must advertise a platform_device for the driver to attach.
+
+config MTD_NAND_OXNAS
+	tristate "NAND Flash support for Oxford Semiconductor SoC"
+	depends on ARCH_OXNAS || COMPILE_TEST
+	depends on HAS_IOMEM
+	help
+	  This enables the NAND flash controller on Oxford Semiconductor SoCs.
+
+config MTD_NAND_FSL_ELBC
+	tristate "NAND support for Freescale eLBC controllers"
+	depends on FSL_SOC
+	select FSL_LBC
+	help
+	  Various Freescale chips, including the 8313, include a NAND Flash
+	  Controller Module with built-in hardware ECC capabilities.
+	  Enabling this option will enable you to use this to control
+	  external NAND devices.
+
+config MTD_NAND_FSL_IFC
+	tristate "NAND support for Freescale IFC controller"
+	depends on FSL_SOC || ARCH_LAYERSCAPE || SOC_LS1021A
+	select FSL_IFC
+	select MEMORY
+	help
+	  Various Freescale chips e.g P1010, include a NAND Flash machine
+	  with built-in hardware ECC capabilities.
+	  Enabling this option will enable you to use this to control
+	  external NAND devices.
+
+config MTD_NAND_FSL_UPM
+	tristate "Support for NAND on Freescale UPM"
+	depends on PPC_83xx || PPC_85xx
+	select FSL_LBC
+	help
+	  Enables support for NAND Flash chips wired onto Freescale PowerPC
+	  processor localbus with User-Programmable Machine support.
+
+config MTD_NAND_MPC5121_NFC
+	tristate "MPC5121 built-in NAND Flash Controller support"
+	depends on PPC_MPC512x
+	help
+	  This enables the driver for the NAND flash controller on the
+	  MPC5121 SoC.
+
+config MTD_NAND_VF610_NFC
+	tristate "Support for Freescale NFC for VF610/MPC5125"
+	depends on (SOC_VF610 || COMPILE_TEST)
+	depends on HAS_IOMEM
+	help
+	  Enables support for NAND Flash Controller on some Freescale
+	  processors like the VF610, MPC5125, MCF54418 or Kinetis K70.
+	  The driver supports a maximum 2k page size. With 2k pages and
+	  64 bytes or more of OOB, hardware ECC with up to 32-bit error
+	  correction is supported. Hardware ECC is only enabled through
+	  device tree.
+
+config MTD_NAND_MXC
+	tristate "MXC NAND support"
+	depends on ARCH_MXC
+	help
+	  This enables the driver for the NAND flash controller on the
+	  MXC processors.
+
+config MTD_NAND_SH_FLCTL
+	tristate "Support for NAND on Renesas SuperH FLCTL"
+	depends on SUPERH || COMPILE_TEST
+	depends on HAS_IOMEM
+	depends on HAS_DMA
+	help
+	  Several Renesas SuperH CPU has FLCTL. This option enables support
+	  for NAND Flash using FLCTL.
+
+config MTD_NAND_DAVINCI
+        tristate "Support NAND on DaVinci/Keystone SoC"
+        depends on ARCH_DAVINCI || (ARCH_KEYSTONE && TI_AEMIF)
+        help
+	  Enable the driver for NAND flash chips on Texas Instruments
+	  DaVinci/Keystone processors.
+
+config MTD_NAND_TXX9NDFMC
+	tristate "NAND Flash support for TXx9 SoC"
+	depends on SOC_TX4938 || SOC_TX4939
+	help
+	  This enables the NAND flash controller on the TXx9 SoCs.
+
+config MTD_NAND_SOCRATES
+	tristate "Support for NAND on Socrates board"
+	depends on SOCRATES
+	help
+	  Enables support for NAND Flash chips wired onto Socrates board.
+
+config MTD_NAND_NUC900
+	tristate "Support for NAND on Nuvoton NUC9xx/w90p910 evaluation boards."
+	depends on ARCH_W90X900
+	help
+	  This enables the driver for the NAND Flash on evaluation board based
+	  on w90p910 / NUC9xx.
+
+config MTD_NAND_JZ4740
+	tristate "Support for JZ4740 SoC NAND controller"
+	depends on MACH_JZ4740
+	help
+		Enables support for NAND Flash on JZ4740 SoC based boards.
+
+config MTD_NAND_JZ4780
+	tristate "Support for NAND on JZ4780 SoC"
+	depends on MACH_JZ4780 && JZ4780_NEMC
+	help
+	  Enables support for NAND Flash connected to the NEMC on JZ4780 SoC
+	  based boards, using the BCH controller for hardware error correction.
+
+config MTD_NAND_FSMC
+	tristate "Support for NAND on ST Micros FSMC"
+	depends on OF
+	depends on PLAT_SPEAR || ARCH_NOMADIK || ARCH_U8500 || MACH_U300
+	help
+	  Enables support for NAND Flash chips on the ST Microelectronics
+	  Flexible Static Memory Controller (FSMC)
+
+config MTD_NAND_XWAY
+	bool "Support for NAND on Lantiq XWAY SoC"
+	depends on LANTIQ && SOC_TYPE_XWAY
+	help
+	  Enables support for NAND Flash chips on Lantiq XWAY SoCs. NAND is attached
+	  to the External Bus Unit (EBU).
+
+config MTD_NAND_SUNXI
+	tristate "Support for NAND on Allwinner SoCs"
+	depends on ARCH_SUNXI
+	help
+	  Enables support for NAND Flash chips on Allwinner SoCs.
+
+config MTD_NAND_HISI504
+	tristate "Support for NAND controller on Hisilicon SoC Hip04"
+	depends on ARCH_HISI || COMPILE_TEST
+	depends on HAS_DMA
+	help
+	  Enables support for NAND controller on Hisilicon SoC Hip04.
+
+config MTD_NAND_QCOM
+	tristate "Support for NAND on QCOM SoCs"
+	depends on ARCH_QCOM
+	help
+	  Enables support for NAND flash chips on SoCs containing the EBI2 NAND
+	  controller. This controller is found on IPQ806x SoC.
+
+config MTD_NAND_MTK
+	tristate "Support for NAND controller on MTK SoCs"
+	depends on ARCH_MEDIATEK || COMPILE_TEST
+	depends on HAS_DMA
+	help
+	  Enables support for NAND controller on MTK SoCs.
+	  This controller is found on mt27xx, mt81xx, mt65xx SoCs.
+
+endif # MTD_NAND
diff --git a/drivers/mtd/nand/raw/Makefile b/drivers/mtd/nand/raw/Makefile
new file mode 100644
index 000000000000..165b7ef9e9a1
--- /dev/null
+++ b/drivers/mtd/nand/raw/Makefile
@@ -0,0 +1,66 @@
+# SPDX-License-Identifier: GPL-2.0
+
+obj-$(CONFIG_MTD_NAND)			+= nand.o
+obj-$(CONFIG_MTD_NAND_ECC)		+= nand_ecc.o
+obj-$(CONFIG_MTD_NAND_BCH)		+= nand_bch.o
+obj-$(CONFIG_MTD_SM_COMMON) 		+= sm_common.o
+
+obj-$(CONFIG_MTD_NAND_CAFE)		+= cafe_nand.o
+obj-$(CONFIG_MTD_NAND_AMS_DELTA)	+= ams-delta.o
+obj-$(CONFIG_MTD_NAND_DENALI)		+= denali.o
+obj-$(CONFIG_MTD_NAND_DENALI_PCI)	+= denali_pci.o
+obj-$(CONFIG_MTD_NAND_DENALI_DT)	+= denali_dt.o
+obj-$(CONFIG_MTD_NAND_AU1550)		+= au1550nd.o
+obj-$(CONFIG_MTD_NAND_S3C2410)		+= s3c2410.o
+obj-$(CONFIG_MTD_NAND_TANGO)		+= tango_nand.o
+obj-$(CONFIG_MTD_NAND_DAVINCI)		+= davinci_nand.o
+obj-$(CONFIG_MTD_NAND_DISKONCHIP)	+= diskonchip.o
+obj-$(CONFIG_MTD_NAND_DOCG4)		+= docg4.o
+obj-$(CONFIG_MTD_NAND_FSMC)		+= fsmc_nand.o
+obj-$(CONFIG_MTD_NAND_SHARPSL)		+= sharpsl.o
+obj-$(CONFIG_MTD_NAND_NANDSIM)		+= nandsim.o
+obj-$(CONFIG_MTD_NAND_CS553X)		+= cs553x_nand.o
+obj-$(CONFIG_MTD_NAND_NDFC)		+= ndfc.o
+obj-$(CONFIG_MTD_NAND_ATMEL)		+= atmel/
+obj-$(CONFIG_MTD_NAND_GPIO)		+= gpio.o
+omap2_nand-objs := omap2.o
+obj-$(CONFIG_MTD_NAND_OMAP2) 		+= omap2_nand.o
+obj-$(CONFIG_MTD_NAND_OMAP_BCH_BUILD)	+= omap_elm.o
+obj-$(CONFIG_MTD_NAND_CM_X270)		+= cmx270_nand.o
+obj-$(CONFIG_MTD_NAND_MARVELL)		+= marvell_nand.o
+obj-$(CONFIG_MTD_NAND_TMIO)		+= tmio_nand.o
+obj-$(CONFIG_MTD_NAND_PLATFORM)		+= plat_nand.o
+obj-$(CONFIG_MTD_NAND_PASEMI)		+= pasemi_nand.o
+obj-$(CONFIG_MTD_NAND_ORION)		+= orion_nand.o
+obj-$(CONFIG_MTD_NAND_OXNAS)		+= oxnas_nand.o
+obj-$(CONFIG_MTD_NAND_FSL_ELBC)		+= fsl_elbc_nand.o
+obj-$(CONFIG_MTD_NAND_FSL_IFC)		+= fsl_ifc_nand.o
+obj-$(CONFIG_MTD_NAND_FSL_UPM)		+= fsl_upm.o
+obj-$(CONFIG_MTD_NAND_SLC_LPC32XX)      += lpc32xx_slc.o
+obj-$(CONFIG_MTD_NAND_MLC_LPC32XX)      += lpc32xx_mlc.o
+obj-$(CONFIG_MTD_NAND_SH_FLCTL)		+= sh_flctl.o
+obj-$(CONFIG_MTD_NAND_MXC)		+= mxc_nand.o
+obj-$(CONFIG_MTD_NAND_SOCRATES)		+= socrates_nand.o
+obj-$(CONFIG_MTD_NAND_TXX9NDFMC)	+= txx9ndfmc.o
+obj-$(CONFIG_MTD_NAND_NUC900)		+= nuc900_nand.o
+obj-$(CONFIG_MTD_NAND_MPC5121_NFC)	+= mpc5121_nfc.o
+obj-$(CONFIG_MTD_NAND_VF610_NFC)	+= vf610_nfc.o
+obj-$(CONFIG_MTD_NAND_RICOH)		+= r852.o
+obj-$(CONFIG_MTD_NAND_JZ4740)		+= jz4740_nand.o
+obj-$(CONFIG_MTD_NAND_JZ4780)		+= jz4780_nand.o jz4780_bch.o
+obj-$(CONFIG_MTD_NAND_GPMI_NAND)	+= gpmi-nand/
+obj-$(CONFIG_MTD_NAND_XWAY)		+= xway_nand.o
+obj-$(CONFIG_MTD_NAND_BCM47XXNFLASH)	+= bcm47xxnflash/
+obj-$(CONFIG_MTD_NAND_SUNXI)		+= sunxi_nand.o
+obj-$(CONFIG_MTD_NAND_HISI504)	        += hisi504_nand.o
+obj-$(CONFIG_MTD_NAND_BRCMNAND)		+= brcmnand/
+obj-$(CONFIG_MTD_NAND_QCOM)		+= qcom_nandc.o
+obj-$(CONFIG_MTD_NAND_MTK)		+= mtk_ecc.o mtk_nand.o
+
+nand-objs := nand_base.o nand_bbt.o nand_timings.o nand_ids.o
+nand-objs += nand_amd.o
+nand-objs += nand_hynix.o
+nand-objs += nand_macronix.o
+nand-objs += nand_micron.o
+nand-objs += nand_samsung.o
+nand-objs += nand_toshiba.o
diff --git a/drivers/mtd/nand/ams-delta.c b/drivers/mtd/nand/raw/ams-delta.c
index d60ada45c549..37a3cc21c7bc 100644
--- a/drivers/mtd/nand/ams-delta.c
+++ b/drivers/mtd/nand/raw/ams-delta.c
@@ -1,11 +1,12 @@
 /*
- *  drivers/mtd/nand/ams-delta.c
- *
  *  Copyright (C) 2006 Jonathan McDowell <noodles@earth.li>
  *
- *  Derived from drivers/mtd/toto.c
+ *  Derived from drivers/mtd/nand/toto.c (removed in v2.6.28)
+ *    Copyright (c) 2003 Texas Instruments
+ *    Copyright (c) 2002 Thomas Gleixner <tgxl@linutronix.de>
+ *
  *  Converted to platform driver by Janusz Krzysztofik <jkrzyszt@tis.icnet.pl>
- *  Partially stolen from drivers/mtd/nand/plat_nand.c
+ *  Partially stolen from plat_nand.c
  *
  * This program is free software; you can redistribute it and/or modify
  * it under the terms of the GNU General Public License version 2 as
@@ -185,7 +186,7 @@ static int ams_delta_init(struct platform_device *pdev)
 	/* Allocate memory for MTD device structure and private data */
 	this = kzalloc(sizeof(struct nand_chip), GFP_KERNEL);
 	if (!this) {
-		printk (KERN_WARNING "Unable to allocate E3 NAND MTD device structure.\n");
+		pr_warn("Unable to allocate E3 NAND MTD device structure.\n");
 		err = -ENOMEM;
 		goto out;
 	}
@@ -219,7 +220,7 @@ static int ams_delta_init(struct platform_device *pdev)
 		this->dev_ready = ams_delta_nand_ready;
 	} else {
 		this->dev_ready = NULL;
-		printk(KERN_NOTICE "Couldn't request gpio for Delta NAND ready.\n");
+		pr_notice("Couldn't request gpio for Delta NAND ready.\n");
 	}
 	/* 25 us command delay time */
 	this->chip_delay = 30;
diff --git a/drivers/mtd/nand/atmel/Makefile b/drivers/mtd/nand/raw/atmel/Makefile
index 288db4f38a8f..288db4f38a8f 100644
--- a/drivers/mtd/nand/atmel/Makefile
+++ b/drivers/mtd/nand/raw/atmel/Makefile
diff --git a/drivers/mtd/nand/atmel/nand-controller.c b/drivers/mtd/nand/raw/atmel/nand-controller.c
index b2f00b398490..12f6753d47ae 100644
--- a/drivers/mtd/nand/atmel/nand-controller.c
+++ b/drivers/mtd/nand/raw/atmel/nand-controller.c
@@ -9,10 +9,10 @@
  *
  *   Copyright 2003 Rick Bronson
  *
- *   Derived from drivers/mtd/nand/autcpu12.c
+ *   Derived from drivers/mtd/nand/autcpu12.c (removed in v3.8)
  *	Copyright 2001 Thomas Gleixner (gleixner@autronix.de)
  *
- *   Derived from drivers/mtd/spia.c
+ *   Derived from drivers/mtd/spia.c (removed in v3.8)
  *	Copyright 2000 Steven J. Hill (sjhill@cotw.com)
  *
  *
diff --git a/drivers/mtd/nand/atmel/pmecc.c b/drivers/mtd/nand/raw/atmel/pmecc.c
index ca0a70389ba9..555a74e15269 100644
--- a/drivers/mtd/nand/atmel/pmecc.c
+++ b/drivers/mtd/nand/raw/atmel/pmecc.c
@@ -9,10 +9,10 @@
  *
  *   Copyright 2003 Rick Bronson
  *
- *   Derived from drivers/mtd/nand/autcpu12.c
+ *   Derived from drivers/mtd/nand/autcpu12.c (removed in v3.8)
  *	Copyright 2001 Thomas Gleixner (gleixner@autronix.de)
  *
- *   Derived from drivers/mtd/spia.c
+ *   Derived from drivers/mtd/spia.c (removed in v3.8)
  *	Copyright 2000 Steven J. Hill (sjhill@cotw.com)
  *
  *   Add Hardware ECC support for AT91SAM9260 / AT91SAM9263
diff --git a/drivers/mtd/nand/atmel/pmecc.h b/drivers/mtd/nand/raw/atmel/pmecc.h
index 817e0dd9fd15..808f1be0d6ad 100644
--- a/drivers/mtd/nand/atmel/pmecc.h
+++ b/drivers/mtd/nand/raw/atmel/pmecc.h
@@ -9,10 +9,10 @@
  *
  *    Copyright © 2003 Rick Bronson
  *
- *    Derived from drivers/mtd/nand/autcpu12.c
+ *    Derived from drivers/mtd/nand/autcpu12.c (removed in v3.8)
  *        Copyright © 2001 Thomas Gleixner (gleixner@autronix.de)
  *
- *    Derived from drivers/mtd/spia.c
+ *    Derived from drivers/mtd/spia.c (removed in v3.8)
  *        Copyright © 2000 Steven J. Hill (sjhill@cotw.com)
  *
  *
diff --git a/drivers/mtd/nand/au1550nd.c b/drivers/mtd/nand/raw/au1550nd.c
index 8ab827edf94e..df0ef1f1e2f5 100644
--- a/drivers/mtd/nand/au1550nd.c
+++ b/drivers/mtd/nand/raw/au1550nd.c
@@ -1,6 +1,4 @@
 /*
- *  drivers/mtd/nand/au1550nd.c
- *
  *  Copyright (C) 2004 Embedded Edge, LLC
  *
  * This program is free software; you can redistribute it and/or modify
diff --git a/drivers/mtd/nand/bcm47xxnflash/Makefile b/drivers/mtd/nand/raw/bcm47xxnflash/Makefile
index f05b119e134b..f05b119e134b 100644
--- a/drivers/mtd/nand/bcm47xxnflash/Makefile
+++ b/drivers/mtd/nand/raw/bcm47xxnflash/Makefile
diff --git a/drivers/mtd/nand/bcm47xxnflash/bcm47xxnflash.h b/drivers/mtd/nand/raw/bcm47xxnflash/bcm47xxnflash.h
index 201b9baa52a0..201b9baa52a0 100644
--- a/drivers/mtd/nand/bcm47xxnflash/bcm47xxnflash.h
+++ b/drivers/mtd/nand/raw/bcm47xxnflash/bcm47xxnflash.h
diff --git a/drivers/mtd/nand/bcm47xxnflash/main.c b/drivers/mtd/nand/raw/bcm47xxnflash/main.c
index fb31429b70a9..fb31429b70a9 100644
--- a/drivers/mtd/nand/bcm47xxnflash/main.c
+++ b/drivers/mtd/nand/raw/bcm47xxnflash/main.c
diff --git a/drivers/mtd/nand/bcm47xxnflash/ops_bcm4706.c b/drivers/mtd/nand/raw/bcm47xxnflash/ops_bcm4706.c
index 54bac5b73f0a..60874de430eb 100644
--- a/drivers/mtd/nand/bcm47xxnflash/ops_bcm4706.c
+++ b/drivers/mtd/nand/raw/bcm47xxnflash/ops_bcm4706.c
@@ -392,8 +392,8 @@ int bcm47xxnflash_ops_bcm4706_init(struct bcm47xxnflash *b47n)
 	b47n->nand_chip.read_byte = bcm47xxnflash_ops_bcm4706_read_byte;
 	b47n->nand_chip.read_buf = bcm47xxnflash_ops_bcm4706_read_buf;
 	b47n->nand_chip.write_buf = bcm47xxnflash_ops_bcm4706_write_buf;
-	b47n->nand_chip.onfi_set_features = nand_onfi_get_set_features_notsupp;
-	b47n->nand_chip.onfi_get_features = nand_onfi_get_set_features_notsupp;
+	b47n->nand_chip.set_features = nand_get_set_features_notsupp;
+	b47n->nand_chip.get_features = nand_get_set_features_notsupp;
 
 	nand_chip->chip_delay = 50;
 	b47n->nand_chip.bbt_options = NAND_BBT_USE_FLASH;
diff --git a/drivers/mtd/nand/brcmnand/Makefile b/drivers/mtd/nand/raw/brcmnand/Makefile
index 195b845e48b8..195b845e48b8 100644
--- a/drivers/mtd/nand/brcmnand/Makefile
+++ b/drivers/mtd/nand/raw/brcmnand/Makefile
diff --git a/drivers/mtd/nand/brcmnand/bcm63138_nand.c b/drivers/mtd/nand/raw/brcmnand/bcm63138_nand.c
index 59444b3a697d..59444b3a697d 100644
--- a/drivers/mtd/nand/brcmnand/bcm63138_nand.c
+++ b/drivers/mtd/nand/raw/brcmnand/bcm63138_nand.c
diff --git a/drivers/mtd/nand/brcmnand/bcm6368_nand.c b/drivers/mtd/nand/raw/brcmnand/bcm6368_nand.c
index 34c91b0e1e69..34c91b0e1e69 100644
--- a/drivers/mtd/nand/brcmnand/bcm6368_nand.c
+++ b/drivers/mtd/nand/raw/brcmnand/bcm6368_nand.c
diff --git a/drivers/mtd/nand/brcmnand/brcmnand.c b/drivers/mtd/nand/raw/brcmnand/brcmnand.c
index c28fd2bc1a84..1306aaa7a8bf 100644
--- a/drivers/mtd/nand/brcmnand/brcmnand.c
+++ b/drivers/mtd/nand/raw/brcmnand/brcmnand.c
@@ -2297,7 +2297,11 @@ static int brcmnand_init_cs(struct brcmnand_host *host, struct device_node *dn)
 	if (ret)
 		return ret;
 
-	return mtd_device_register(mtd, NULL, 0);
+	ret = mtd_device_register(mtd, NULL, 0);
+	if (ret)
+		nand_cleanup(chip);
+
+	return ret;
 }
 
 static void brcmnand_save_restore_cs_config(struct brcmnand_host *host,
diff --git a/drivers/mtd/nand/brcmnand/brcmnand.h b/drivers/mtd/nand/raw/brcmnand/brcmnand.h
index 5c44cd4aba87..5c44cd4aba87 100644
--- a/drivers/mtd/nand/brcmnand/brcmnand.h
+++ b/drivers/mtd/nand/raw/brcmnand/brcmnand.h
diff --git a/drivers/mtd/nand/brcmnand/brcmstb_nand.c b/drivers/mtd/nand/raw/brcmnand/brcmstb_nand.c
index 5c271077ac87..5c271077ac87 100644
--- a/drivers/mtd/nand/brcmnand/brcmstb_nand.c
+++ b/drivers/mtd/nand/raw/brcmnand/brcmstb_nand.c
diff --git a/drivers/mtd/nand/brcmnand/iproc_nand.c b/drivers/mtd/nand/raw/brcmnand/iproc_nand.c
index 4c6ae113664d..4c6ae113664d 100644
--- a/drivers/mtd/nand/brcmnand/iproc_nand.c
+++ b/drivers/mtd/nand/raw/brcmnand/iproc_nand.c
diff --git a/drivers/mtd/nand/cafe_nand.c b/drivers/mtd/nand/raw/cafe_nand.c
index 567ff972d5fc..d8c8c9d1e640 100644
--- a/drivers/mtd/nand/cafe_nand.c
+++ b/drivers/mtd/nand/raw/cafe_nand.c
@@ -645,8 +645,8 @@ static int cafe_nand_probe(struct pci_dev *pdev,
 	cafe->nand.read_buf = cafe_read_buf;
 	cafe->nand.write_buf = cafe_write_buf;
 	cafe->nand.select_chip = cafe_select_chip;
-	cafe->nand.onfi_set_features = nand_onfi_get_set_features_notsupp;
-	cafe->nand.onfi_get_features = nand_onfi_get_set_features_notsupp;
+	cafe->nand.set_features = nand_get_set_features_notsupp;
+	cafe->nand.get_features = nand_get_set_features_notsupp;
 
 	cafe->nand.chip_delay = 0;
 
@@ -751,8 +751,8 @@ static int cafe_nand_probe(struct pci_dev *pdev,
 		cafe->nand.bbt_td = &cafe_bbt_main_descr_512;
 		cafe->nand.bbt_md = &cafe_bbt_mirror_descr_512;
 	} else {
-		printk(KERN_WARNING "Unexpected NAND flash writesize %d. Aborting\n",
-		       mtd->writesize);
+		pr_warn("Unexpected NAND flash writesize %d. Aborting\n",
+			mtd->writesize);
 		goto out_free_dma;
 	}
 	cafe->nand.ecc.mode = NAND_ECC_HW_SYNDROME;
@@ -774,10 +774,14 @@ static int cafe_nand_probe(struct pci_dev *pdev,
 	pci_set_drvdata(pdev, mtd);
 
 	mtd->name = "cafe_nand";
-	mtd_device_parse_register(mtd, part_probes, NULL, NULL, 0);
+	err = mtd_device_parse_register(mtd, part_probes, NULL, NULL, 0);
+	if (err)
+		goto out_cleanup_nand;
 
 	goto out;
 
+ out_cleanup_nand:
+	nand_cleanup(&cafe->nand);
  out_free_dma:
 	dma_free_coherent(&cafe->pdev->dev, 2112, cafe->dmabuf, cafe->dmaaddr);
  out_irq:
diff --git a/drivers/mtd/nand/cmx270_nand.c b/drivers/mtd/nand/raw/cmx270_nand.c
index b01c9804590e..02d6751e9efe 100644
--- a/drivers/mtd/nand/cmx270_nand.c
+++ b/drivers/mtd/nand/raw/cmx270_nand.c
@@ -1,10 +1,8 @@
 /*
- *  linux/drivers/mtd/nand/cmx270-nand.c
- *
  *  Copyright (C) 2006 Compulab, Ltd.
  *  Mike Rapoport <mike@compulab.co.il>
  *
- *  Derived from drivers/mtd/nand/h1910.c
+ *  Derived from drivers/mtd/nand/h1910.c (removed in v3.10)
  *       Copyright (C) 2002 Marius Gröger (mag@sysgo.de)
  *       Copyright (c) 2001 Thomas Gleixner (gleixner@autronix.de)
  *
diff --git a/drivers/mtd/nand/cs553x_nand.c b/drivers/mtd/nand/raw/cs553x_nand.c
index d48877540f14..82269fde9e66 100644
--- a/drivers/mtd/nand/cs553x_nand.c
+++ b/drivers/mtd/nand/raw/cs553x_nand.c
@@ -1,6 +1,4 @@
 /*
- * drivers/mtd/nand/cs553x_nand.c
- *
  * (C) 2005, 2006 Red Hat Inc.
  *
  * Author: David Woodhouse <dwmw2@infradead.org>
@@ -189,10 +187,11 @@ static int __init cs553x_init_one(int cs, int mmio, unsigned long adr)
 	struct nand_chip *this;
 	struct mtd_info *new_mtd;
 
-	printk(KERN_NOTICE "Probing CS553x NAND controller CS#%d at %sIO 0x%08lx\n", cs, mmio?"MM":"P", adr);
+	pr_notice("Probing CS553x NAND controller CS#%d at %sIO 0x%08lx\n",
+		  cs, mmio ? "MM" : "P", adr);
 
 	if (!mmio) {
-		printk(KERN_NOTICE "PIO mode not yet implemented for CS553X NAND controller\n");
+		pr_notice("PIO mode not yet implemented for CS553X NAND controller\n");
 		return -ENXIO;
 	}
 
@@ -211,7 +210,7 @@ static int __init cs553x_init_one(int cs, int mmio, unsigned long adr)
 	/* map physical address */
 	this->IO_ADDR_R = this->IO_ADDR_W = ioremap(adr, 4096);
 	if (!this->IO_ADDR_R) {
-		printk(KERN_WARNING "ioremap cs553x NAND @0x%08lx failed\n", adr);
+		pr_warn("ioremap cs553x NAND @0x%08lx failed\n", adr);
 		err = -EIO;
 		goto out_mtd;
 	}
@@ -295,7 +294,7 @@ static int __init cs553x_init(void)
 	/* If it doesn't have the NAND controller enabled, abort */
 	rdmsrl(MSR_DIVIL_BALL_OPTS, val);
 	if (val & PIN_OPT_IDE) {
-		printk(KERN_INFO "CS553x NAND controller: Flash I/O not enabled in MSR_DIVIL_BALL_OPTS.\n");
+		pr_info("CS553x NAND controller: Flash I/O not enabled in MSR_DIVIL_BALL_OPTS.\n");
 		return -ENXIO;
 	}
 
diff --git a/drivers/mtd/nand/davinci_nand.c b/drivers/mtd/nand/raw/davinci_nand.c
index ccc8c43abcff..0f09518d980f 100644
--- a/drivers/mtd/nand/davinci_nand.c
+++ b/drivers/mtd/nand/raw/davinci_nand.c
@@ -826,7 +826,7 @@ static int nand_davinci_probe(struct platform_device *pdev)
 	else
 		ret = mtd_device_register(mtd, NULL, 0);
 	if (ret < 0)
-		goto err;
+		goto err_cleanup_nand;
 
 	val = davinci_nand_readl(info, NRCSR_OFFSET);
 	dev_info(&pdev->dev, "controller rev. %d.%d\n",
@@ -834,6 +834,9 @@ static int nand_davinci_probe(struct platform_device *pdev)
 
 	return 0;
 
+err_cleanup_nand:
+	nand_cleanup(&info->chip);
+
 err:
 	clk_disable_unprepare(info->clk);
 
diff --git a/drivers/mtd/nand/denali.c b/drivers/mtd/nand/raw/denali.c
index 313c7f50621b..2a302a1d1430 100644
--- a/drivers/mtd/nand/denali.c
+++ b/drivers/mtd/nand/raw/denali.c
@@ -1384,10 +1384,12 @@ int denali_init(struct denali_nand_info *denali)
 	ret = mtd_device_register(mtd, NULL, 0);
 	if (ret) {
 		dev_err(denali->dev, "Failed to register MTD: %d\n", ret);
-		goto free_buf;
+		goto cleanup_nand;
 	}
 	return 0;
 
+cleanup_nand:
+	nand_cleanup(chip);
 free_buf:
 	kfree(denali->buf);
 disable_irq:
diff --git a/drivers/mtd/nand/denali.h b/drivers/mtd/nand/raw/denali.h
index 9ad33d237378..9ad33d237378 100644
--- a/drivers/mtd/nand/denali.h
+++ b/drivers/mtd/nand/raw/denali.h
diff --git a/drivers/mtd/nand/denali_dt.c b/drivers/mtd/nand/raw/denali_dt.c
index cfd33e6ca77f..cfd33e6ca77f 100644
--- a/drivers/mtd/nand/denali_dt.c
+++ b/drivers/mtd/nand/raw/denali_dt.c
diff --git a/drivers/mtd/nand/denali_pci.c b/drivers/mtd/nand/raw/denali_pci.c
index 49cb3e1f8bd0..49cb3e1f8bd0 100644
--- a/drivers/mtd/nand/denali_pci.c
+++ b/drivers/mtd/nand/raw/denali_pci.c
diff --git a/drivers/mtd/nand/diskonchip.c b/drivers/mtd/nand/raw/diskonchip.c
index 6bc93ea66f50..86a258de0b75 100644
--- a/drivers/mtd/nand/diskonchip.c
+++ b/drivers/mtd/nand/raw/diskonchip.c
@@ -1,6 +1,4 @@
 /*
- * drivers/mtd/nand/diskonchip.c
- *
  * (C) 2003 Red Hat, Inc.
  * (C) 2004 Dan Brown <dan_brown@ieee.org>
  * (C) 2004 Kalev Lember <kalev@smartlink.ee>
@@ -411,7 +409,7 @@ static uint16_t __init doc200x_ident_chip(struct mtd_info *mtd, int nr)
 
 		ident.dword = readl(docptr + DoC_2k_CDSN_IO);
 		if (((ident.byte[0] << 8) | ident.byte[1]) == ret) {
-			printk(KERN_INFO "DiskOnChip 2000 responds to DWORD access\n");
+			pr_info("DiskOnChip 2000 responds to DWORD access\n");
 			this->read_buf = &doc2000_readbuf_dword;
 		}
 	}
@@ -438,7 +436,7 @@ static void __init doc2000_count_chips(struct mtd_info *mtd)
 			break;
 	}
 	doc->chips_per_floor = i;
-	printk(KERN_DEBUG "Detected %d chips per floor.\n", i);
+	pr_debug("Detected %d chips per floor.\n", i);
 }
 
 static int doc200x_wait(struct mtd_info *mtd, struct nand_chip *this)
@@ -934,14 +932,15 @@ static int doc200x_correct_data(struct mtd_info *mtd, u_char *dat,
 
 		ret = doc_ecc_decode(rs_decoder, dat, calc_ecc);
 		if (ret > 0)
-			printk(KERN_ERR "doc200x_correct_data corrected %d errors\n", ret);
+			pr_err("doc200x_correct_data corrected %d errors\n",
+			       ret);
 	}
 	if (DoC_is_MillenniumPlus(doc))
 		WriteDOC(DOC_ECC_DIS, docptr, Mplus_ECCConf);
 	else
 		WriteDOC(DOC_ECC_DIS, docptr, ECCConf);
 	if (no_ecc_failures && mtd_is_eccerr(ret)) {
-		printk(KERN_ERR "suppressing ECC failure\n");
+		pr_err("suppressing ECC failure\n");
 		ret = 0;
 	}
 	return ret;
@@ -1014,11 +1013,11 @@ static int __init find_media_headers(struct mtd_info *mtd, u_char *buf, const ch
 		if (retlen != mtd->writesize)
 			continue;
 		if (ret) {
-			printk(KERN_WARNING "ECC error scanning DOC at 0x%x\n", offs);
+			pr_warn("ECC error scanning DOC at 0x%x\n", offs);
 		}
 		if (memcmp(buf, id, 6))
 			continue;
-		printk(KERN_INFO "Found DiskOnChip %s Media Header at 0x%x\n", id, offs);
+		pr_info("Found DiskOnChip %s Media Header at 0x%x\n", id, offs);
 		if (doc->mh0_page == -1) {
 			doc->mh0_page = offs >> this->page_shift;
 			if (!findmirror)
@@ -1029,7 +1028,7 @@ static int __init find_media_headers(struct mtd_info *mtd, u_char *buf, const ch
 		return 2;
 	}
 	if (doc->mh0_page == -1) {
-		printk(KERN_WARNING "DiskOnChip %s Media Header not found.\n", id);
+		pr_warn("DiskOnChip %s Media Header not found.\n", id);
 		return 0;
 	}
 	/* Only one mediaheader was found.  We want buf to contain a
@@ -1038,7 +1037,7 @@ static int __init find_media_headers(struct mtd_info *mtd, u_char *buf, const ch
 	ret = mtd_read(mtd, offs, mtd->writesize, &retlen, buf);
 	if (retlen != mtd->writesize) {
 		/* Insanity.  Give up. */
-		printk(KERN_ERR "Read DiskOnChip Media Header once, but can't reread it???\n");
+		pr_err("Read DiskOnChip Media Header once, but can't reread it???\n");
 		return 0;
 	}
 	return 1;
@@ -1068,11 +1067,11 @@ static inline int __init nftl_partscan(struct mtd_info *mtd, struct mtd_partitio
 	le16_to_cpus(&mh->FirstPhysicalEUN);
 	le32_to_cpus(&mh->FormattedSize);
 
-	printk(KERN_INFO "    DataOrgID        = %s\n"
-			 "    NumEraseUnits    = %d\n"
-			 "    FirstPhysicalEUN = %d\n"
-			 "    FormattedSize    = %d\n"
-			 "    UnitSizeFactor   = %d\n",
+	pr_info("    DataOrgID        = %s\n"
+		"    NumEraseUnits    = %d\n"
+		"    FirstPhysicalEUN = %d\n"
+		"    FormattedSize    = %d\n"
+		"    UnitSizeFactor   = %d\n",
 		mh->DataOrgID, mh->NumEraseUnits,
 		mh->FirstPhysicalEUN, mh->FormattedSize,
 		mh->UnitSizeFactor);
@@ -1092,7 +1091,7 @@ static inline int __init nftl_partscan(struct mtd_info *mtd, struct mtd_partitio
 			maxblocks = min(32768U, (maxblocks << 1) + psize);
 			mh->UnitSizeFactor--;
 		}
-		printk(KERN_WARNING "UnitSizeFactor=0x00 detected.  Correct value is assumed to be 0x%02x.\n", mh->UnitSizeFactor);
+		pr_warn("UnitSizeFactor=0x00 detected.  Correct value is assumed to be 0x%02x.\n", mh->UnitSizeFactor);
 	}
 
 	/* NOTE: The lines below modify internal variables of the NAND and MTD
@@ -1103,13 +1102,13 @@ static inline int __init nftl_partscan(struct mtd_info *mtd, struct mtd_partitio
 	if (mh->UnitSizeFactor != 0xff) {
 		this->bbt_erase_shift += (0xff - mh->UnitSizeFactor);
 		mtd->erasesize <<= (0xff - mh->UnitSizeFactor);
-		printk(KERN_INFO "Setting virtual erase size to %d\n", mtd->erasesize);
+		pr_info("Setting virtual erase size to %d\n", mtd->erasesize);
 		blocks = mtd->size >> this->bbt_erase_shift;
 		maxblocks = min(32768U, mtd->erasesize - psize);
 	}
 
 	if (blocks > maxblocks) {
-		printk(KERN_ERR "UnitSizeFactor of 0x%02x is inconsistent with device size.  Aborting.\n", mh->UnitSizeFactor);
+		pr_err("UnitSizeFactor of 0x%02x is inconsistent with device size.  Aborting.\n", mh->UnitSizeFactor);
 		goto out;
 	}
 
@@ -1180,14 +1179,14 @@ static inline int __init inftl_partscan(struct mtd_info *mtd, struct mtd_partiti
 	le32_to_cpus(&mh->FormatFlags);
 	le32_to_cpus(&mh->PercentUsed);
 
-	printk(KERN_INFO "    bootRecordID          = %s\n"
-			 "    NoOfBootImageBlocks   = %d\n"
-			 "    NoOfBinaryPartitions  = %d\n"
-			 "    NoOfBDTLPartitions    = %d\n"
-			 "    BlockMultiplerBits    = %d\n"
-			 "    FormatFlgs            = %d\n"
-			 "    OsakVersion           = %d.%d.%d.%d\n"
-			 "    PercentUsed           = %d\n",
+	pr_info("    bootRecordID          = %s\n"
+		"    NoOfBootImageBlocks   = %d\n"
+		"    NoOfBinaryPartitions  = %d\n"
+		"    NoOfBDTLPartitions    = %d\n"
+		"    BlockMultiplerBits    = %d\n"
+		"    FormatFlgs            = %d\n"
+		"    OsakVersion           = %d.%d.%d.%d\n"
+		"    PercentUsed           = %d\n",
 		mh->bootRecordID, mh->NoOfBootImageBlocks,
 		mh->NoOfBinaryPartitions,
 		mh->NoOfBDTLPartitions,
@@ -1202,13 +1201,13 @@ static inline int __init inftl_partscan(struct mtd_info *mtd, struct mtd_partiti
 
 	blocks = mtd->size >> vshift;
 	if (blocks > 32768) {
-		printk(KERN_ERR "BlockMultiplierBits=%d is inconsistent with device size.  Aborting.\n", mh->BlockMultiplierBits);
+		pr_err("BlockMultiplierBits=%d is inconsistent with device size.  Aborting.\n", mh->BlockMultiplierBits);
 		goto out;
 	}
 
 	blocks = doc->chips_per_floor << (this->chip_shift - this->phys_erase_shift);
 	if (inftl_bbt_write && (blocks > mtd->erasesize)) {
-		printk(KERN_ERR "Writeable BBTs spanning more than one erase block are not yet supported.  FIX ME!\n");
+		pr_err("Writeable BBTs spanning more than one erase block are not yet supported.  FIX ME!\n");
 		goto out;
 	}
 
@@ -1222,7 +1221,7 @@ static inline int __init inftl_partscan(struct mtd_info *mtd, struct mtd_partiti
 		le32_to_cpus(&ip->spareUnits);
 		le32_to_cpus(&ip->Reserved0);
 
-		printk(KERN_INFO	"    PARTITION[%d] ->\n"
+		pr_info("    PARTITION[%d] ->\n"
 			"        virtualUnits    = %d\n"
 			"        firstUnit       = %d\n"
 			"        lastUnit        = %d\n"
@@ -1308,7 +1307,7 @@ static int __init inftl_scan_bbt(struct mtd_info *mtd)
 	struct mtd_partition parts[5];
 
 	if (this->numchips > doc->chips_per_floor) {
-		printk(KERN_ERR "Multi-floor INFTL devices not yet supported.\n");
+		pr_err("Multi-floor INFTL devices not yet supported.\n");
 		return -EIO;
 	}
 
@@ -1436,7 +1435,8 @@ static int __init doc_probe(unsigned long physadr)
 		return -EBUSY;
 	virtadr = ioremap(physadr, DOC_IOREMAP_LEN);
 	if (!virtadr) {
-		printk(KERN_ERR "Diskonchip ioremap failed: 0x%x bytes at 0x%lx\n", DOC_IOREMAP_LEN, physadr);
+		pr_err("Diskonchip ioremap failed: 0x%x bytes at 0x%lx\n",
+		       DOC_IOREMAP_LEN, physadr);
 		ret = -EIO;
 		goto error_ioremap;
 	}
@@ -1495,7 +1495,7 @@ static int __init doc_probe(unsigned long physadr)
 			reg = DoC_Mplus_Toggle;
 			break;
 		case DOC_ChipID_DocMilPlus32:
-			printk(KERN_ERR "DiskOnChip Millennium Plus 32MB is not supported, ignoring.\n");
+			pr_err("DiskOnChip Millennium Plus 32MB is not supported, ignoring.\n");
 		default:
 			ret = -ENODEV;
 			goto notfound;
@@ -1511,7 +1511,7 @@ static int __init doc_probe(unsigned long physadr)
 	tmpb = ReadDOC_(virtadr, reg) & DOC_TOGGLE_BIT;
 	tmpc = ReadDOC_(virtadr, reg) & DOC_TOGGLE_BIT;
 	if ((tmp == tmpb) || (tmp != tmpc)) {
-		printk(KERN_WARNING "Possible DiskOnChip at 0x%lx failed TOGGLE test, dropping.\n", physadr);
+		pr_warn("Possible DiskOnChip at 0x%lx failed TOGGLE test, dropping.\n", physadr);
 		ret = -ENODEV;
 		goto notfound;
 	}
@@ -1545,12 +1545,13 @@ static int __init doc_probe(unsigned long physadr)
 		}
 		newval = ~newval;
 		if (oldval == newval) {
-			printk(KERN_DEBUG "Found alias of DOC at 0x%lx to 0x%lx\n", doc->physadr, physadr);
+			pr_debug("Found alias of DOC at 0x%lx to 0x%lx\n",
+				 doc->physadr, physadr);
 			goto notfound;
 		}
 	}
 
-	printk(KERN_NOTICE "DiskOnChip found at 0x%lx\n", physadr);
+	pr_notice("DiskOnChip found at 0x%lx\n", physadr);
 
 	len = sizeof(struct nand_chip) + sizeof(struct doc_priv) +
 	      (2 * sizeof(struct nand_bbt_descr));
@@ -1665,12 +1666,13 @@ static int __init init_nanddoc(void)
 	 */
 	rs_decoder = init_rs(10, 0x409, FCR, 1, NROOTS);
 	if (!rs_decoder) {
-		printk(KERN_ERR "DiskOnChip: Could not create a RS decoder\n");
+		pr_err("DiskOnChip: Could not create a RS decoder\n");
 		return -ENOMEM;
 	}
 
 	if (doc_config_location) {
-		printk(KERN_INFO "Using configured DiskOnChip probe address 0x%lx\n", doc_config_location);
+		pr_info("Using configured DiskOnChip probe address 0x%lx\n",
+			doc_config_location);
 		ret = doc_probe(doc_config_location);
 		if (ret < 0)
 			goto outerr;
@@ -1682,7 +1684,7 @@ static int __init init_nanddoc(void)
 	/* No banner message any more. Print a message if no DiskOnChip
 	   found, so the user knows we at least tried. */
 	if (!doclist) {
-		printk(KERN_INFO "No valid DiskOnChip devices found\n");
+		pr_info("No valid DiskOnChip devices found\n");
 		ret = -ENODEV;
 		goto outerr;
 	}
diff --git a/drivers/mtd/nand/docg4.c b/drivers/mtd/nand/raw/docg4.c
index 72f1327c4430..1314aa99b9ab 100644
--- a/drivers/mtd/nand/docg4.c
+++ b/drivers/mtd/nand/raw/docg4.c
@@ -1269,8 +1269,8 @@ static void __init init_mtd_structs(struct mtd_info *mtd)
 	nand->read_buf = docg4_read_buf;
 	nand->write_buf = docg4_write_buf16;
 	nand->erase = docg4_erase_block;
-	nand->onfi_set_features = nand_onfi_get_set_features_notsupp;
-	nand->onfi_get_features = nand_onfi_get_set_features_notsupp;
+	nand->set_features = nand_get_set_features_notsupp;
+	nand->get_features = nand_get_set_features_notsupp;
 	nand->ecc.read_page = docg4_read_page;
 	nand->ecc.write_page = docg4_write_page;
 	nand->ecc.read_page_raw = docg4_read_page_raw;
diff --git a/drivers/mtd/nand/fsl_elbc_nand.c b/drivers/mtd/nand/raw/fsl_elbc_nand.c
index 8b6dcd739ecb..d28df991c73c 100644
--- a/drivers/mtd/nand/fsl_elbc_nand.c
+++ b/drivers/mtd/nand/raw/fsl_elbc_nand.c
@@ -775,8 +775,8 @@ static int fsl_elbc_chip_init(struct fsl_elbc_mtd *priv)
 	chip->select_chip = fsl_elbc_select_chip;
 	chip->cmdfunc = fsl_elbc_cmdfunc;
 	chip->waitfunc = fsl_elbc_wait;
-	chip->onfi_set_features = nand_onfi_get_set_features_notsupp;
-	chip->onfi_get_features = nand_onfi_get_set_features_notsupp;
+	chip->set_features = nand_get_set_features_notsupp;
+	chip->get_features = nand_get_set_features_notsupp;
 
 	chip->bbt_td = &bbt_main_descr;
 	chip->bbt_md = &bbt_mirror_descr;
@@ -929,8 +929,8 @@ static int fsl_elbc_nand_probe(struct platform_device *pdev)
 	mtd_device_parse_register(mtd, part_probe_types, NULL,
 				  NULL, 0);
 
-	printk(KERN_INFO "eLBC NAND device at 0x%llx, bank %d\n",
-	       (unsigned long long)res.start, priv->bank);
+	pr_info("eLBC NAND device at 0x%llx, bank %d\n",
+		(unsigned long long)res.start, priv->bank);
 	return 0;
 
 err:
diff --git a/drivers/mtd/nand/fsl_ifc_nand.c b/drivers/mtd/nand/raw/fsl_ifc_nand.c
index 5a9c2f0020c2..61aae0224078 100644
--- a/drivers/mtd/nand/fsl_ifc_nand.c
+++ b/drivers/mtd/nand/raw/fsl_ifc_nand.c
@@ -799,7 +799,7 @@ static void fsl_ifc_sram_init(struct fsl_ifc_mtd *priv)
 			   msecs_to_jiffies(IFC_TIMEOUT_MSECS));
 
 	if (ctrl->nand_stat != IFC_NAND_EVTER_STAT_OPC)
-		printk(KERN_ERR "fsl-ifc: Failed to Initialise SRAM\n");
+		pr_err("fsl-ifc: Failed to Initialise SRAM\n");
 
 	/* Restore CSOR and CSOR_ext */
 	ifc_out32(csor, &ifc_global->csor_cs[cs].csor);
@@ -832,8 +832,8 @@ static int fsl_ifc_chip_init(struct fsl_ifc_mtd *priv)
 	chip->select_chip = fsl_ifc_select_chip;
 	chip->cmdfunc = fsl_ifc_cmdfunc;
 	chip->waitfunc = fsl_ifc_wait;
-	chip->onfi_set_features = nand_onfi_get_set_features_notsupp;
-	chip->onfi_get_features = nand_onfi_get_set_features_notsupp;
+	chip->set_features = nand_get_set_features_notsupp;
+	chip->get_features = nand_get_set_features_notsupp;
 
 	chip->bbt_td = &bbt_main_descr;
 	chip->bbt_md = &bbt_mirror_descr;
diff --git a/drivers/mtd/nand/fsl_upm.c b/drivers/mtd/nand/raw/fsl_upm.c
index a88e2cf66e0f..a88e2cf66e0f 100644
--- a/drivers/mtd/nand/fsl_upm.c
+++ b/drivers/mtd/nand/raw/fsl_upm.c
diff --git a/drivers/mtd/nand/fsmc_nand.c b/drivers/mtd/nand/raw/fsmc_nand.c
index f49ed46fa770..28c48dcc514e 100644
--- a/drivers/mtd/nand/fsmc_nand.c
+++ b/drivers/mtd/nand/raw/fsmc_nand.c
@@ -1,6 +1,4 @@
 /*
- * drivers/mtd/nand/fsmc_nand.c
- *
  * ST Microelectronics
  * Flexible Static Memory Controller (FSMC)
  * Driver for NAND portions
@@ -9,7 +7,9 @@
  * Vipin Kumar <vipin.kumar@st.com>
  * Ashish Priyadarshi
  *
- * Based on drivers/mtd/nand/nomadik_nand.c
+ * Based on drivers/mtd/nand/nomadik_nand.c (removed in v3.8)
+ *  Copyright © 2007 STMicroelectronics Pvt. Ltd.
+ *  Copyright © 2009 Alessandro Rubini
  *
  * This file is licensed under the terms of the GNU General Public
  * License version 2. This program is licensed "as is" without any
@@ -103,10 +103,6 @@
 #define ECC3			0x1C
 #define FSMC_NAND_BANK_SZ	0x20
 
-#define FSMC_NAND_REG(base, bank, reg)		(base + FSMC_NOR_REG_SIZE + \
-						(FSMC_NAND_BANK_SZ * (bank)) + \
-						reg)
-
 #define FSMC_BUSY_WAIT_TIMEOUT	(1 * HZ)
 
 struct fsmc_nand_timings {
@@ -143,7 +139,7 @@ enum access_mode {
  * @data_va:		NAND port for Data.
  * @cmd_va:		NAND port for Command.
  * @addr_va:		NAND port for Address.
- * @regs_va:		FSMC regs base address.
+ * @regs_va:		Registers base address for a given bank.
  */
 struct fsmc_nand_data {
 	u32			pid;
@@ -258,45 +254,6 @@ static inline struct fsmc_nand_data *mtd_to_fsmc(struct mtd_info *mtd)
 }
 
 /*
- * fsmc_cmd_ctrl - For facilitaing Hardware access
- * This routine allows hardware specific access to control-lines(ALE,CLE)
- */
-static void fsmc_cmd_ctrl(struct mtd_info *mtd, int cmd, unsigned int ctrl)
-{
-	struct nand_chip *this = mtd_to_nand(mtd);
-	struct fsmc_nand_data *host = mtd_to_fsmc(mtd);
-	void __iomem *regs = host->regs_va;
-	unsigned int bank = host->bank;
-
-	if (ctrl & NAND_CTRL_CHANGE) {
-		u32 pc;
-
-		if (ctrl & NAND_CLE) {
-			this->IO_ADDR_R = host->cmd_va;
-			this->IO_ADDR_W = host->cmd_va;
-		} else if (ctrl & NAND_ALE) {
-			this->IO_ADDR_R = host->addr_va;
-			this->IO_ADDR_W = host->addr_va;
-		} else {
-			this->IO_ADDR_R = host->data_va;
-			this->IO_ADDR_W = host->data_va;
-		}
-
-		pc = readl(FSMC_NAND_REG(regs, bank, PC));
-		if (ctrl & NAND_NCE)
-			pc |= FSMC_ENABLE;
-		else
-			pc &= ~FSMC_ENABLE;
-		writel_relaxed(pc, FSMC_NAND_REG(regs, bank, PC));
-	}
-
-	mb();
-
-	if (cmd != NAND_CMD_NONE)
-		writeb_relaxed(cmd, this->IO_ADDR_W);
-}
-
-/*
  * fsmc_nand_setup - FSMC (Flexible Static Memory Controller) init routine
  *
  * This routine initializes timing parameters related to NAND memory access in
@@ -307,8 +264,6 @@ static void fsmc_nand_setup(struct fsmc_nand_data *host,
 {
 	uint32_t value = FSMC_DEVTYPE_NAND | FSMC_ENABLE | FSMC_WAITON;
 	uint32_t tclr, tar, thiz, thold, twait, tset;
-	unsigned int bank = host->bank;
-	void __iomem *regs = host->regs_va;
 
 	tclr = (tims->tclr & FSMC_TCLR_MASK) << FSMC_TCLR_SHIFT;
 	tar = (tims->tar & FSMC_TAR_MASK) << FSMC_TAR_SHIFT;
@@ -318,18 +273,14 @@ static void fsmc_nand_setup(struct fsmc_nand_data *host,
 	tset = (tims->tset & FSMC_TSET_MASK) << FSMC_TSET_SHIFT;
 
 	if (host->nand.options & NAND_BUSWIDTH_16)
-		writel_relaxed(value | FSMC_DEVWID_16,
-				FSMC_NAND_REG(regs, bank, PC));
+		writel_relaxed(value | FSMC_DEVWID_16, host->regs_va + PC);
 	else
-		writel_relaxed(value | FSMC_DEVWID_8,
-				FSMC_NAND_REG(regs, bank, PC));
-
-	writel_relaxed(readl(FSMC_NAND_REG(regs, bank, PC)) | tclr | tar,
-			FSMC_NAND_REG(regs, bank, PC));
-	writel_relaxed(thiz | thold | twait | tset,
-			FSMC_NAND_REG(regs, bank, COMM));
-	writel_relaxed(thiz | thold | twait | tset,
-			FSMC_NAND_REG(regs, bank, ATTRIB));
+		writel_relaxed(value | FSMC_DEVWID_8, host->regs_va + PC);
+
+	writel_relaxed(readl(host->regs_va + PC) | tclr | tar,
+		       host->regs_va + PC);
+	writel_relaxed(thiz | thold | twait | tset, host->regs_va + COMM);
+	writel_relaxed(thiz | thold | twait | tset, host->regs_va + ATTRIB);
 }
 
 static int fsmc_calc_timings(struct fsmc_nand_data *host,
@@ -419,15 +370,13 @@ static int fsmc_setup_data_interface(struct mtd_info *mtd, int csline,
 static void fsmc_enable_hwecc(struct mtd_info *mtd, int mode)
 {
 	struct fsmc_nand_data *host = mtd_to_fsmc(mtd);
-	void __iomem *regs = host->regs_va;
-	uint32_t bank = host->bank;
-
-	writel_relaxed(readl(FSMC_NAND_REG(regs, bank, PC)) & ~FSMC_ECCPLEN_256,
-			FSMC_NAND_REG(regs, bank, PC));
-	writel_relaxed(readl(FSMC_NAND_REG(regs, bank, PC)) & ~FSMC_ECCEN,
-			FSMC_NAND_REG(regs, bank, PC));
-	writel_relaxed(readl(FSMC_NAND_REG(regs, bank, PC)) | FSMC_ECCEN,
-			FSMC_NAND_REG(regs, bank, PC));
+
+	writel_relaxed(readl(host->regs_va + PC) & ~FSMC_ECCPLEN_256,
+		       host->regs_va + PC);
+	writel_relaxed(readl(host->regs_va + PC) & ~FSMC_ECCEN,
+		       host->regs_va + PC);
+	writel_relaxed(readl(host->regs_va + PC) | FSMC_ECCEN,
+		       host->regs_va + PC);
 }
 
 /*
@@ -439,13 +388,11 @@ static int fsmc_read_hwecc_ecc4(struct mtd_info *mtd, const uint8_t *data,
 				uint8_t *ecc)
 {
 	struct fsmc_nand_data *host = mtd_to_fsmc(mtd);
-	void __iomem *regs = host->regs_va;
-	uint32_t bank = host->bank;
 	uint32_t ecc_tmp;
 	unsigned long deadline = jiffies + FSMC_BUSY_WAIT_TIMEOUT;
 
 	do {
-		if (readl_relaxed(FSMC_NAND_REG(regs, bank, STS)) & FSMC_CODE_RDY)
+		if (readl_relaxed(host->regs_va + STS) & FSMC_CODE_RDY)
 			break;
 		else
 			cond_resched();
@@ -456,25 +403,25 @@ static int fsmc_read_hwecc_ecc4(struct mtd_info *mtd, const uint8_t *data,
 		return -ETIMEDOUT;
 	}
 
-	ecc_tmp = readl_relaxed(FSMC_NAND_REG(regs, bank, ECC1));
+	ecc_tmp = readl_relaxed(host->regs_va + ECC1);
 	ecc[0] = (uint8_t) (ecc_tmp >> 0);
 	ecc[1] = (uint8_t) (ecc_tmp >> 8);
 	ecc[2] = (uint8_t) (ecc_tmp >> 16);
 	ecc[3] = (uint8_t) (ecc_tmp >> 24);
 
-	ecc_tmp = readl_relaxed(FSMC_NAND_REG(regs, bank, ECC2));
+	ecc_tmp = readl_relaxed(host->regs_va + ECC2);
 	ecc[4] = (uint8_t) (ecc_tmp >> 0);
 	ecc[5] = (uint8_t) (ecc_tmp >> 8);
 	ecc[6] = (uint8_t) (ecc_tmp >> 16);
 	ecc[7] = (uint8_t) (ecc_tmp >> 24);
 
-	ecc_tmp = readl_relaxed(FSMC_NAND_REG(regs, bank, ECC3));
+	ecc_tmp = readl_relaxed(host->regs_va + ECC3);
 	ecc[8] = (uint8_t) (ecc_tmp >> 0);
 	ecc[9] = (uint8_t) (ecc_tmp >> 8);
 	ecc[10] = (uint8_t) (ecc_tmp >> 16);
 	ecc[11] = (uint8_t) (ecc_tmp >> 24);
 
-	ecc_tmp = readl_relaxed(FSMC_NAND_REG(regs, bank, STS));
+	ecc_tmp = readl_relaxed(host->regs_va + STS);
 	ecc[12] = (uint8_t) (ecc_tmp >> 16);
 
 	return 0;
@@ -489,11 +436,9 @@ static int fsmc_read_hwecc_ecc1(struct mtd_info *mtd, const uint8_t *data,
 				uint8_t *ecc)
 {
 	struct fsmc_nand_data *host = mtd_to_fsmc(mtd);
-	void __iomem *regs = host->regs_va;
-	uint32_t bank = host->bank;
 	uint32_t ecc_tmp;
 
-	ecc_tmp = readl_relaxed(FSMC_NAND_REG(regs, bank, ECC1));
+	ecc_tmp = readl_relaxed(host->regs_va + ECC1);
 	ecc[0] = (uint8_t) (ecc_tmp >> 0);
 	ecc[1] = (uint8_t) (ecc_tmp >> 8);
 	ecc[2] = (uint8_t) (ecc_tmp >> 16);
@@ -598,18 +543,18 @@ unmap_dma:
  */
 static void fsmc_write_buf(struct mtd_info *mtd, const uint8_t *buf, int len)
 {
+	struct fsmc_nand_data *host  = mtd_to_fsmc(mtd);
 	int i;
-	struct nand_chip *chip = mtd_to_nand(mtd);
 
 	if (IS_ALIGNED((uint32_t)buf, sizeof(uint32_t)) &&
 			IS_ALIGNED(len, sizeof(uint32_t))) {
 		uint32_t *p = (uint32_t *)buf;
 		len = len >> 2;
 		for (i = 0; i < len; i++)
-			writel_relaxed(p[i], chip->IO_ADDR_W);
+			writel_relaxed(p[i], host->data_va);
 	} else {
 		for (i = 0; i < len; i++)
-			writeb_relaxed(buf[i], chip->IO_ADDR_W);
+			writeb_relaxed(buf[i], host->data_va);
 	}
 }
 
@@ -621,18 +566,18 @@ static void fsmc_write_buf(struct mtd_info *mtd, const uint8_t *buf, int len)
  */
 static void fsmc_read_buf(struct mtd_info *mtd, uint8_t *buf, int len)
 {
+	struct fsmc_nand_data *host  = mtd_to_fsmc(mtd);
 	int i;
-	struct nand_chip *chip = mtd_to_nand(mtd);
 
 	if (IS_ALIGNED((uint32_t)buf, sizeof(uint32_t)) &&
 			IS_ALIGNED(len, sizeof(uint32_t))) {
 		uint32_t *p = (uint32_t *)buf;
 		len = len >> 2;
 		for (i = 0; i < len; i++)
-			p[i] = readl_relaxed(chip->IO_ADDR_R);
+			p[i] = readl_relaxed(host->data_va);
 	} else {
 		for (i = 0; i < len; i++)
-			buf[i] = readb_relaxed(chip->IO_ADDR_R);
+			buf[i] = readb_relaxed(host->data_va);
 	}
 }
 
@@ -663,6 +608,102 @@ static void fsmc_write_buf_dma(struct mtd_info *mtd, const uint8_t *buf,
 	dma_xfer(host, (void *)buf, len, DMA_TO_DEVICE);
 }
 
+/* fsmc_select_chip - assert or deassert nCE */
+static void fsmc_select_chip(struct mtd_info *mtd, int chipnr)
+{
+	struct fsmc_nand_data *host = mtd_to_fsmc(mtd);
+	u32 pc;
+
+	/* Support only one CS */
+	if (chipnr > 0)
+		return;
+
+	pc = readl(host->regs_va + PC);
+	if (chipnr < 0)
+		writel_relaxed(pc & ~FSMC_ENABLE, host->regs_va + PC);
+	else
+		writel_relaxed(pc | FSMC_ENABLE, host->regs_va + PC);
+
+	/* nCE line must be asserted before starting any operation */
+	mb();
+}
+
+/*
+ * fsmc_exec_op - hook called by the core to execute NAND operations
+ *
+ * This controller is simple enough and thus does not need to use the parser
+ * provided by the core, instead, handle every situation here.
+ */
+static int fsmc_exec_op(struct nand_chip *chip, const struct nand_operation *op,
+			bool check_only)
+{
+	struct mtd_info *mtd = nand_to_mtd(chip);
+	struct fsmc_nand_data *host = mtd_to_fsmc(mtd);
+	const struct nand_op_instr *instr = NULL;
+	int ret = 0;
+	unsigned int op_id;
+	int i;
+
+	pr_debug("Executing operation [%d instructions]:\n", op->ninstrs);
+	for (op_id = 0; op_id < op->ninstrs; op_id++) {
+		instr = &op->instrs[op_id];
+
+		switch (instr->type) {
+		case NAND_OP_CMD_INSTR:
+			pr_debug("  ->CMD      [0x%02x]\n",
+				 instr->ctx.cmd.opcode);
+
+			writeb_relaxed(instr->ctx.cmd.opcode, host->cmd_va);
+			break;
+
+		case NAND_OP_ADDR_INSTR:
+			pr_debug("  ->ADDR     [%d cyc]",
+				 instr->ctx.addr.naddrs);
+
+			for (i = 0; i < instr->ctx.addr.naddrs; i++)
+				writeb_relaxed(instr->ctx.addr.addrs[i],
+					       host->addr_va);
+			break;
+
+		case NAND_OP_DATA_IN_INSTR:
+			pr_debug("  ->DATA_IN  [%d B%s]\n", instr->ctx.data.len,
+				 instr->ctx.data.force_8bit ?
+				 ", force 8-bit" : "");
+
+			if (host->mode == USE_DMA_ACCESS)
+				fsmc_read_buf_dma(mtd, instr->ctx.data.buf.in,
+						  instr->ctx.data.len);
+			else
+				fsmc_read_buf(mtd, instr->ctx.data.buf.in,
+					      instr->ctx.data.len);
+			break;
+
+		case NAND_OP_DATA_OUT_INSTR:
+			pr_debug("  ->DATA_OUT [%d B%s]\n", instr->ctx.data.len,
+				 instr->ctx.data.force_8bit ?
+				 ", force 8-bit" : "");
+
+			if (host->mode == USE_DMA_ACCESS)
+				fsmc_write_buf_dma(mtd, instr->ctx.data.buf.out,
+						   instr->ctx.data.len);
+			else
+				fsmc_write_buf(mtd, instr->ctx.data.buf.out,
+					       instr->ctx.data.len);
+			break;
+
+		case NAND_OP_WAITRDY_INSTR:
+			pr_debug("  ->WAITRDY  [max %d ms]\n",
+				 instr->ctx.waitrdy.timeout_ms);
+
+			ret = nand_soft_waitrdy(chip,
+						instr->ctx.waitrdy.timeout_ms);
+			break;
+		}
+	}
+
+	return ret;
+}
+
 /*
  * fsmc_read_page_hwecc
  * @mtd:	mtd info structure
@@ -754,13 +795,11 @@ static int fsmc_bch8_correct_data(struct mtd_info *mtd, uint8_t *dat,
 {
 	struct nand_chip *chip = mtd_to_nand(mtd);
 	struct fsmc_nand_data *host = mtd_to_fsmc(mtd);
-	void __iomem *regs = host->regs_va;
-	unsigned int bank = host->bank;
 	uint32_t err_idx[8];
 	uint32_t num_err, i;
 	uint32_t ecc1, ecc2, ecc3, ecc4;
 
-	num_err = (readl_relaxed(FSMC_NAND_REG(regs, bank, STS)) >> 10) & 0xF;
+	num_err = (readl_relaxed(host->regs_va + STS) >> 10) & 0xF;
 
 	/* no bit flipping */
 	if (likely(num_err == 0))
@@ -803,10 +842,10 @@ static int fsmc_bch8_correct_data(struct mtd_info *mtd, uint8_t *dat,
 	 * uint64_t array and error offset indexes are populated in err_idx
 	 * array
 	 */
-	ecc1 = readl_relaxed(FSMC_NAND_REG(regs, bank, ECC1));
-	ecc2 = readl_relaxed(FSMC_NAND_REG(regs, bank, ECC2));
-	ecc3 = readl_relaxed(FSMC_NAND_REG(regs, bank, ECC3));
-	ecc4 = readl_relaxed(FSMC_NAND_REG(regs, bank, STS));
+	ecc1 = readl_relaxed(host->regs_va + ECC1);
+	ecc2 = readl_relaxed(host->regs_va + ECC2);
+	ecc3 = readl_relaxed(host->regs_va + ECC3);
+	ecc4 = readl_relaxed(host->regs_va + STS);
 
 	err_idx[0] = (ecc1 >> 0) & 0x1FFF;
 	err_idx[1] = (ecc1 >> 13) & 0x1FFF;
@@ -889,6 +928,7 @@ static int __init fsmc_nand_probe(struct platform_device *pdev)
 	struct mtd_info *mtd;
 	struct nand_chip *nand;
 	struct resource *res;
+	void __iomem *base;
 	dma_cap_mask_t mask;
 	int ret = 0;
 	u32 pid;
@@ -923,9 +963,12 @@ static int __init fsmc_nand_probe(struct platform_device *pdev)
 		return PTR_ERR(host->cmd_va);
 
 	res = platform_get_resource_byname(pdev, IORESOURCE_MEM, "fsmc_regs");
-	host->regs_va = devm_ioremap_resource(&pdev->dev, res);
-	if (IS_ERR(host->regs_va))
-		return PTR_ERR(host->regs_va);
+	base = devm_ioremap_resource(&pdev->dev, res);
+	if (IS_ERR(base))
+		return PTR_ERR(base);
+
+	host->regs_va = base + FSMC_NOR_REG_SIZE +
+		(host->bank * FSMC_NAND_BANK_SZ);
 
 	host->clk = devm_clk_get(&pdev->dev, NULL);
 	if (IS_ERR(host->clk)) {
@@ -942,7 +985,7 @@ static int __init fsmc_nand_probe(struct platform_device *pdev)
 	 * AMBA PrimeCell bus. However it is not a PrimeCell.
 	 */
 	for (pid = 0, i = 0; i < 4; i++)
-		pid |= (readl(host->regs_va + resource_size(res) - 0x20 + 4 * i) & 255) << (i * 8);
+		pid |= (readl(base + resource_size(res) - 0x20 + 4 * i) & 255) << (i * 8);
 	host->pid = pid;
 	dev_info(&pdev->dev, "FSMC device partno %03x, manufacturer %02x, "
 		 "revision %02x, config %02x\n",
@@ -960,9 +1003,8 @@ static int __init fsmc_nand_probe(struct platform_device *pdev)
 	nand_set_flash_node(nand, pdev->dev.of_node);
 
 	mtd->dev.parent = &pdev->dev;
-	nand->IO_ADDR_R = host->data_va;
-	nand->IO_ADDR_W = host->data_va;
-	nand->cmd_ctrl = fsmc_cmd_ctrl;
+	nand->exec_op = fsmc_exec_op;
+	nand->select_chip = fsmc_select_chip;
 	nand->chip_delay = 30;
 
 	/*
@@ -974,8 +1016,7 @@ static int __init fsmc_nand_probe(struct platform_device *pdev)
 	nand->ecc.size = 512;
 	nand->badblockbits = 7;
 
-	switch (host->mode) {
-	case USE_DMA_ACCESS:
+	if (host->mode == USE_DMA_ACCESS) {
 		dma_cap_zero(mask);
 		dma_cap_set(DMA_MEMCPY, mask);
 		host->read_dma_chan = dma_request_channel(mask, filter, NULL);
@@ -988,15 +1029,6 @@ static int __init fsmc_nand_probe(struct platform_device *pdev)
 			dev_err(&pdev->dev, "Unable to get write dma channel\n");
 			goto err_req_write_chnl;
 		}
-		nand->read_buf = fsmc_read_buf_dma;
-		nand->write_buf = fsmc_write_buf_dma;
-		break;
-
-	default:
-	case USE_WORD_ACCESS:
-		nand->read_buf = fsmc_read_buf;
-		nand->write_buf = fsmc_write_buf;
-		break;
 	}
 
 	if (host->dev_timings)
diff --git a/drivers/mtd/nand/gpio.c b/drivers/mtd/nand/raw/gpio.c
index a8bde6665c24..2780af26d9ab 100644
--- a/drivers/mtd/nand/gpio.c
+++ b/drivers/mtd/nand/raw/gpio.c
@@ -1,6 +1,4 @@
 /*
- * drivers/mtd/nand/gpio.c
- *
  * Updated, and converted to generic GPIO based driver by Russell King.
  *
  * Written by Ben Dooks <ben@simtec.co.uk>
diff --git a/drivers/mtd/nand/gpmi-nand/Makefile b/drivers/mtd/nand/raw/gpmi-nand/Makefile
index 3a462487c35e..3a462487c35e 100644
--- a/drivers/mtd/nand/gpmi-nand/Makefile
+++ b/drivers/mtd/nand/raw/gpmi-nand/Makefile
diff --git a/drivers/mtd/nand/gpmi-nand/bch-regs.h b/drivers/mtd/nand/raw/gpmi-nand/bch-regs.h
index 05bb91f2f4c4..05bb91f2f4c4 100644
--- a/drivers/mtd/nand/gpmi-nand/bch-regs.h
+++ b/drivers/mtd/nand/raw/gpmi-nand/bch-regs.h
diff --git a/drivers/mtd/nand/gpmi-nand/gpmi-lib.c b/drivers/mtd/nand/raw/gpmi-nand/gpmi-lib.c
index 97787246af41..e94556705dc7 100644
--- a/drivers/mtd/nand/gpmi-nand/gpmi-lib.c
+++ b/drivers/mtd/nand/raw/gpmi-nand/gpmi-lib.c
@@ -26,15 +26,8 @@
 #include "gpmi-regs.h"
 #include "bch-regs.h"
 
-static struct timing_threshold timing_default_threshold = {
-	.max_data_setup_cycles       = (BM_GPMI_TIMING0_DATA_SETUP >>
-						BP_GPMI_TIMING0_DATA_SETUP),
-	.internal_data_setup_in_ns   = 0,
-	.max_sample_delay_factor     = (BM_GPMI_CTRL1_RDN_DELAY >>
-						BP_GPMI_CTRL1_RDN_DELAY),
-	.max_dll_clock_period_in_ns  = 32,
-	.max_dll_delay_in_ns         = 16,
-};
+/* Converts time to clock cycles */
+#define TO_CYCLES(duration, period) DIV_ROUND_UP_ULL(duration, period)
 
 #define MXS_SET_ADDR		0x4
 #define MXS_CLR_ADDR		0x8
@@ -151,8 +144,15 @@ err_clk:
 	return ret;
 }
 
-#define gpmi_enable_clk(x) __gpmi_enable_clk(x, true)
-#define gpmi_disable_clk(x) __gpmi_enable_clk(x, false)
+int gpmi_enable_clk(struct gpmi_nand_data *this)
+{
+	return __gpmi_enable_clk(this, true);
+}
+
+int gpmi_disable_clk(struct gpmi_nand_data *this)
+{
+	return __gpmi_enable_clk(this, false);
+}
 
 int gpmi_init(struct gpmi_nand_data *this)
 {
@@ -174,7 +174,6 @@ int gpmi_init(struct gpmi_nand_data *this)
 	if (ret)
 		goto err_out;
 
-
 	/* Choose NAND mode. */
 	writel(BM_GPMI_CTRL1_GPMI_MODE, r->gpmi_regs + HW_GPMI_CTRL1_CLR);
 
@@ -313,467 +312,6 @@ err_out:
 	return ret;
 }
 
-/* Converts time in nanoseconds to cycles. */
-static unsigned int ns_to_cycles(unsigned int time,
-			unsigned int period, unsigned int min)
-{
-	unsigned int k;
-
-	k = (time + period - 1) / period;
-	return max(k, min);
-}
-
-#define DEF_MIN_PROP_DELAY	5
-#define DEF_MAX_PROP_DELAY	9
-/* Apply timing to current hardware conditions. */
-static int gpmi_nfc_compute_hardware_timing(struct gpmi_nand_data *this,
-					struct gpmi_nfc_hardware_timing *hw)
-{
-	struct timing_threshold *nfc = &timing_default_threshold;
-	struct resources *r = &this->resources;
-	struct nand_chip *nand = &this->nand;
-	struct nand_timing target = this->timing;
-	bool improved_timing_is_available;
-	unsigned long clock_frequency_in_hz;
-	unsigned int clock_period_in_ns;
-	bool dll_use_half_periods;
-	unsigned int dll_delay_shift;
-	unsigned int max_sample_delay_in_ns;
-	unsigned int address_setup_in_cycles;
-	unsigned int data_setup_in_ns;
-	unsigned int data_setup_in_cycles;
-	unsigned int data_hold_in_cycles;
-	int ideal_sample_delay_in_ns;
-	unsigned int sample_delay_factor;
-	int tEYE;
-	unsigned int min_prop_delay_in_ns = DEF_MIN_PROP_DELAY;
-	unsigned int max_prop_delay_in_ns = DEF_MAX_PROP_DELAY;
-
-	/*
-	 * If there are multiple chips, we need to relax the timings to allow
-	 * for signal distortion due to higher capacitance.
-	 */
-	if (nand->numchips > 2) {
-		target.data_setup_in_ns    += 10;
-		target.data_hold_in_ns     += 10;
-		target.address_setup_in_ns += 10;
-	} else if (nand->numchips > 1) {
-		target.data_setup_in_ns    += 5;
-		target.data_hold_in_ns     += 5;
-		target.address_setup_in_ns += 5;
-	}
-
-	/* Check if improved timing information is available. */
-	improved_timing_is_available =
-		(target.tREA_in_ns  >= 0) &&
-		(target.tRLOH_in_ns >= 0) &&
-		(target.tRHOH_in_ns >= 0);
-
-	/* Inspect the clock. */
-	nfc->clock_frequency_in_hz = clk_get_rate(r->clock[0]);
-	clock_frequency_in_hz = nfc->clock_frequency_in_hz;
-	clock_period_in_ns    = NSEC_PER_SEC / clock_frequency_in_hz;
-
-	/*
-	 * The NFC quantizes setup and hold parameters in terms of clock cycles.
-	 * Here, we quantize the setup and hold timing parameters to the
-	 * next-highest clock period to make sure we apply at least the
-	 * specified times.
-	 *
-	 * For data setup and data hold, the hardware interprets a value of zero
-	 * as the largest possible delay. This is not what's intended by a zero
-	 * in the input parameter, so we impose a minimum of one cycle.
-	 */
-	data_setup_in_cycles    = ns_to_cycles(target.data_setup_in_ns,
-							clock_period_in_ns, 1);
-	data_hold_in_cycles     = ns_to_cycles(target.data_hold_in_ns,
-							clock_period_in_ns, 1);
-	address_setup_in_cycles = ns_to_cycles(target.address_setup_in_ns,
-							clock_period_in_ns, 0);
-
-	/*
-	 * The clock's period affects the sample delay in a number of ways:
-	 *
-	 * (1) The NFC HAL tells us the maximum clock period the sample delay
-	 *     DLL can tolerate. If the clock period is greater than half that
-	 *     maximum, we must configure the DLL to be driven by half periods.
-	 *
-	 * (2) We need to convert from an ideal sample delay, in ns, to a
-	 *     "sample delay factor," which the NFC uses. This factor depends on
-	 *     whether we're driving the DLL with full or half periods.
-	 *     Paraphrasing the reference manual:
-	 *
-	 *         AD = SDF x 0.125 x RP
-	 *
-	 * where:
-	 *
-	 *     AD   is the applied delay, in ns.
-	 *     SDF  is the sample delay factor, which is dimensionless.
-	 *     RP   is the reference period, in ns, which is a full clock period
-	 *          if the DLL is being driven by full periods, or half that if
-	 *          the DLL is being driven by half periods.
-	 *
-	 * Let's re-arrange this in a way that's more useful to us:
-	 *
-	 *                        8
-	 *         SDF  =  AD x ----
-	 *                       RP
-	 *
-	 * The reference period is either the clock period or half that, so this
-	 * is:
-	 *
-	 *                        8       AD x DDF
-	 *         SDF  =  AD x -----  =  --------
-	 *                      f x P        P
-	 *
-	 * where:
-	 *
-	 *       f  is 1 or 1/2, depending on how we're driving the DLL.
-	 *       P  is the clock period.
-	 *     DDF  is the DLL Delay Factor, a dimensionless value that
-	 *          incorporates all the constants in the conversion.
-	 *
-	 * DDF will be either 8 or 16, both of which are powers of two. We can
-	 * reduce the cost of this conversion by using bit shifts instead of
-	 * multiplication or division. Thus:
-	 *
-	 *                 AD << DDS
-	 *         SDF  =  ---------
-	 *                     P
-	 *
-	 *     or
-	 *
-	 *         AD  =  (SDF >> DDS) x P
-	 *
-	 * where:
-	 *
-	 *     DDS  is the DLL Delay Shift, the logarithm to base 2 of the DDF.
-	 */
-	if (clock_period_in_ns > (nfc->max_dll_clock_period_in_ns >> 1)) {
-		dll_use_half_periods = true;
-		dll_delay_shift      = 3 + 1;
-	} else {
-		dll_use_half_periods = false;
-		dll_delay_shift      = 3;
-	}
-
-	/*
-	 * Compute the maximum sample delay the NFC allows, under current
-	 * conditions. If the clock is running too slowly, no sample delay is
-	 * possible.
-	 */
-	if (clock_period_in_ns > nfc->max_dll_clock_period_in_ns)
-		max_sample_delay_in_ns = 0;
-	else {
-		/*
-		 * Compute the delay implied by the largest sample delay factor
-		 * the NFC allows.
-		 */
-		max_sample_delay_in_ns =
-			(nfc->max_sample_delay_factor * clock_period_in_ns) >>
-								dll_delay_shift;
-
-		/*
-		 * Check if the implied sample delay larger than the NFC
-		 * actually allows.
-		 */
-		if (max_sample_delay_in_ns > nfc->max_dll_delay_in_ns)
-			max_sample_delay_in_ns = nfc->max_dll_delay_in_ns;
-	}
-
-	/*
-	 * Check if improved timing information is available. If not, we have to
-	 * use a less-sophisticated algorithm.
-	 */
-	if (!improved_timing_is_available) {
-		/*
-		 * Fold the read setup time required by the NFC into the ideal
-		 * sample delay.
-		 */
-		ideal_sample_delay_in_ns = target.gpmi_sample_delay_in_ns +
-						nfc->internal_data_setup_in_ns;
-
-		/*
-		 * The ideal sample delay may be greater than the maximum
-		 * allowed by the NFC. If so, we can trade off sample delay time
-		 * for more data setup time.
-		 *
-		 * In each iteration of the following loop, we add a cycle to
-		 * the data setup time and subtract a corresponding amount from
-		 * the sample delay until we've satisified the constraints or
-		 * can't do any better.
-		 */
-		while ((ideal_sample_delay_in_ns > max_sample_delay_in_ns) &&
-			(data_setup_in_cycles < nfc->max_data_setup_cycles)) {
-
-			data_setup_in_cycles++;
-			ideal_sample_delay_in_ns -= clock_period_in_ns;
-
-			if (ideal_sample_delay_in_ns < 0)
-				ideal_sample_delay_in_ns = 0;
-
-		}
-
-		/*
-		 * Compute the sample delay factor that corresponds most closely
-		 * to the ideal sample delay. If the result is too large for the
-		 * NFC, use the maximum value.
-		 *
-		 * Notice that we use the ns_to_cycles function to compute the
-		 * sample delay factor. We do this because the form of the
-		 * computation is the same as that for calculating cycles.
-		 */
-		sample_delay_factor =
-			ns_to_cycles(
-				ideal_sample_delay_in_ns << dll_delay_shift,
-							clock_period_in_ns, 0);
-
-		if (sample_delay_factor > nfc->max_sample_delay_factor)
-			sample_delay_factor = nfc->max_sample_delay_factor;
-
-		/* Skip to the part where we return our results. */
-		goto return_results;
-	}
-
-	/*
-	 * If control arrives here, we have more detailed timing information,
-	 * so we can use a better algorithm.
-	 */
-
-	/*
-	 * Fold the read setup time required by the NFC into the maximum
-	 * propagation delay.
-	 */
-	max_prop_delay_in_ns += nfc->internal_data_setup_in_ns;
-
-	/*
-	 * Earlier, we computed the number of clock cycles required to satisfy
-	 * the data setup time. Now, we need to know the actual nanoseconds.
-	 */
-	data_setup_in_ns = clock_period_in_ns * data_setup_in_cycles;
-
-	/*
-	 * Compute tEYE, the width of the data eye when reading from the NAND
-	 * Flash. The eye width is fundamentally determined by the data setup
-	 * time, perturbed by propagation delays and some characteristics of the
-	 * NAND Flash device.
-	 *
-	 * start of the eye = max_prop_delay + tREA
-	 * end of the eye   = min_prop_delay + tRHOH + data_setup
-	 */
-	tEYE = (int)min_prop_delay_in_ns + (int)target.tRHOH_in_ns +
-							(int)data_setup_in_ns;
-
-	tEYE -= (int)max_prop_delay_in_ns + (int)target.tREA_in_ns;
-
-	/*
-	 * The eye must be open. If it's not, we can try to open it by
-	 * increasing its main forcer, the data setup time.
-	 *
-	 * In each iteration of the following loop, we increase the data setup
-	 * time by a single clock cycle. We do this until either the eye is
-	 * open or we run into NFC limits.
-	 */
-	while ((tEYE <= 0) &&
-			(data_setup_in_cycles < nfc->max_data_setup_cycles)) {
-		/* Give a cycle to data setup. */
-		data_setup_in_cycles++;
-		/* Synchronize the data setup time with the cycles. */
-		data_setup_in_ns += clock_period_in_ns;
-		/* Adjust tEYE accordingly. */
-		tEYE += clock_period_in_ns;
-	}
-
-	/*
-	 * When control arrives here, the eye is open. The ideal time to sample
-	 * the data is in the center of the eye:
-	 *
-	 *     end of the eye + start of the eye
-	 *     ---------------------------------  -  data_setup
-	 *                    2
-	 *
-	 * After some algebra, this simplifies to the code immediately below.
-	 */
-	ideal_sample_delay_in_ns =
-		((int)max_prop_delay_in_ns +
-			(int)target.tREA_in_ns +
-				(int)min_prop_delay_in_ns +
-					(int)target.tRHOH_in_ns -
-						(int)data_setup_in_ns) >> 1;
-
-	/*
-	 * The following figure illustrates some aspects of a NAND Flash read:
-	 *
-	 *
-	 *           __                   _____________________________________
-	 * RDN         \_________________/
-	 *
-	 *                                         <---- tEYE ----->
-	 *                                        /-----------------\
-	 * Read Data ----------------------------<                   >---------
-	 *                                        \-----------------/
-	 *             ^                 ^                 ^              ^
-	 *             |                 |                 |              |
-	 *             |<--Data Setup -->|<--Delay Time -->|              |
-	 *             |                 |                 |              |
-	 *             |                 |                                |
-	 *             |                 |<--   Quantized Delay Time   -->|
-	 *             |                 |                                |
-	 *
-	 *
-	 * We have some issues we must now address:
-	 *
-	 * (1) The *ideal* sample delay time must not be negative. If it is, we
-	 *     jam it to zero.
-	 *
-	 * (2) The *ideal* sample delay time must not be greater than that
-	 *     allowed by the NFC. If it is, we can increase the data setup
-	 *     time, which will reduce the delay between the end of the data
-	 *     setup and the center of the eye. It will also make the eye
-	 *     larger, which might help with the next issue...
-	 *
-	 * (3) The *quantized* sample delay time must not fall either before the
-	 *     eye opens or after it closes (the latter is the problem
-	 *     illustrated in the above figure).
-	 */
-
-	/* Jam a negative ideal sample delay to zero. */
-	if (ideal_sample_delay_in_ns < 0)
-		ideal_sample_delay_in_ns = 0;
-
-	/*
-	 * Extend the data setup as needed to reduce the ideal sample delay
-	 * below the maximum permitted by the NFC.
-	 */
-	while ((ideal_sample_delay_in_ns > max_sample_delay_in_ns) &&
-			(data_setup_in_cycles < nfc->max_data_setup_cycles)) {
-
-		/* Give a cycle to data setup. */
-		data_setup_in_cycles++;
-		/* Synchronize the data setup time with the cycles. */
-		data_setup_in_ns += clock_period_in_ns;
-		/* Adjust tEYE accordingly. */
-		tEYE += clock_period_in_ns;
-
-		/*
-		 * Decrease the ideal sample delay by one half cycle, to keep it
-		 * in the middle of the eye.
-		 */
-		ideal_sample_delay_in_ns -= (clock_period_in_ns >> 1);
-
-		/* Jam a negative ideal sample delay to zero. */
-		if (ideal_sample_delay_in_ns < 0)
-			ideal_sample_delay_in_ns = 0;
-	}
-
-	/*
-	 * Compute the sample delay factor that corresponds to the ideal sample
-	 * delay. If the result is too large, then use the maximum allowed
-	 * value.
-	 *
-	 * Notice that we use the ns_to_cycles function to compute the sample
-	 * delay factor. We do this because the form of the computation is the
-	 * same as that for calculating cycles.
-	 */
-	sample_delay_factor =
-		ns_to_cycles(ideal_sample_delay_in_ns << dll_delay_shift,
-							clock_period_in_ns, 0);
-
-	if (sample_delay_factor > nfc->max_sample_delay_factor)
-		sample_delay_factor = nfc->max_sample_delay_factor;
-
-	/*
-	 * These macros conveniently encapsulate a computation we'll use to
-	 * continuously evaluate whether or not the data sample delay is inside
-	 * the eye.
-	 */
-	#define IDEAL_DELAY  ((int) ideal_sample_delay_in_ns)
-
-	#define QUANTIZED_DELAY  \
-		((int) ((sample_delay_factor * clock_period_in_ns) >> \
-							dll_delay_shift))
-
-	#define DELAY_ERROR  (abs(QUANTIZED_DELAY - IDEAL_DELAY))
-
-	#define SAMPLE_IS_NOT_WITHIN_THE_EYE  (DELAY_ERROR > (tEYE >> 1))
-
-	/*
-	 * While the quantized sample time falls outside the eye, reduce the
-	 * sample delay or extend the data setup to move the sampling point back
-	 * toward the eye. Do not allow the number of data setup cycles to
-	 * exceed the maximum allowed by the NFC.
-	 */
-	while (SAMPLE_IS_NOT_WITHIN_THE_EYE &&
-			(data_setup_in_cycles < nfc->max_data_setup_cycles)) {
-		/*
-		 * If control arrives here, the quantized sample delay falls
-		 * outside the eye. Check if it's before the eye opens, or after
-		 * the eye closes.
-		 */
-		if (QUANTIZED_DELAY > IDEAL_DELAY) {
-			/*
-			 * If control arrives here, the quantized sample delay
-			 * falls after the eye closes. Decrease the quantized
-			 * delay time and then go back to re-evaluate.
-			 */
-			if (sample_delay_factor != 0)
-				sample_delay_factor--;
-			continue;
-		}
-
-		/*
-		 * If control arrives here, the quantized sample delay falls
-		 * before the eye opens. Shift the sample point by increasing
-		 * data setup time. This will also make the eye larger.
-		 */
-
-		/* Give a cycle to data setup. */
-		data_setup_in_cycles++;
-		/* Synchronize the data setup time with the cycles. */
-		data_setup_in_ns += clock_period_in_ns;
-		/* Adjust tEYE accordingly. */
-		tEYE += clock_period_in_ns;
-
-		/*
-		 * Decrease the ideal sample delay by one half cycle, to keep it
-		 * in the middle of the eye.
-		 */
-		ideal_sample_delay_in_ns -= (clock_period_in_ns >> 1);
-
-		/* ...and one less period for the delay time. */
-		ideal_sample_delay_in_ns -= clock_period_in_ns;
-
-		/* Jam a negative ideal sample delay to zero. */
-		if (ideal_sample_delay_in_ns < 0)
-			ideal_sample_delay_in_ns = 0;
-
-		/*
-		 * We have a new ideal sample delay, so re-compute the quantized
-		 * delay.
-		 */
-		sample_delay_factor =
-			ns_to_cycles(
-				ideal_sample_delay_in_ns << dll_delay_shift,
-							clock_period_in_ns, 0);
-
-		if (sample_delay_factor > nfc->max_sample_delay_factor)
-			sample_delay_factor = nfc->max_sample_delay_factor;
-	}
-
-	/* Control arrives here when we're ready to return our results. */
-return_results:
-	hw->data_setup_in_cycles    = data_setup_in_cycles;
-	hw->data_hold_in_cycles     = data_hold_in_cycles;
-	hw->address_setup_in_cycles = address_setup_in_cycles;
-	hw->use_half_periods        = dll_use_half_periods;
-	hw->sample_delay_factor     = sample_delay_factor;
-	hw->device_busy_timeout     = GPMI_DEFAULT_BUSY_TIMEOUT;
-	hw->wrn_dly_sel             = BV_GPMI_CTRL1_WRN_DLY_SEL_4_TO_8NS;
-
-	/* Return success. */
-	return 0;
-}
-
 /*
  * <1> Firstly, we should know what's the GPMI-clock means.
  *     The GPMI-clock is the internal clock in the gpmi nand controller.
@@ -824,13 +362,10 @@ return_results:
  *  4.1) From the aspect of the nand chip pins:
  *        Delay = (tREA + C - tRP)               {1}
  *
- *        tREA : the maximum read access time. From the ONFI nand standards,
- *               we know that tREA is 16ns in mode 5, tREA is 20ns is mode 4.
- *               Please check it in : www.onfi.org
- *        C    : a constant for adjust the delay. default is 4.
- *        tRP  : the read pulse width.
- *               Specified by the HW_GPMI_TIMING0:DATA_SETUP:
- *                    tRP = (GPMI-clock-period) * DATA_SETUP
+ *        tREA : the maximum read access time.
+ *        C    : a constant to adjust the delay. default is 4000ps.
+ *        tRP  : the read pulse width, which is exactly:
+ *                   tRP = (GPMI-clock-period) * DATA_SETUP
  *
  *  4.2) From the aspect of the GPMI nand controller:
  *         Delay = RDN_DELAY * 0.125 * RP        {2}
@@ -843,239 +378,137 @@ return_results:
  *
  *            Set the HW_GPMI_CTRL1:HALF_PERIOD if GPMI-clock-period
  *            is greater DLL_THRETHOLD. In other SOCs, the DLL_THRETHOLD
- *            is 16ns, but in mx6q, we use 12ns.
+ *            is 16000ps, but in mx6q, we use 12000ps.
  *
  *  4.3) since {1} equals {2}, we get:
  *
- *                    (tREA + 4 - tRP) * 8
- *         RDN_DELAY = ---------------------     {3}
+ *                     (tREA + 4000 - tRP) * 8
+ *         RDN_DELAY = -----------------------     {3}
  *                           RP
- *
- *  4.4) We only support the fastest asynchronous mode of ONFI nand.
- *       For some ONFI nand, the mode 4 is the fastest mode;
- *       while for some ONFI nand, the mode 5 is the fastest mode.
- *       So we only support the mode 4 and mode 5. It is no need to
- *       support other modes.
  */
-static void gpmi_compute_edo_timing(struct gpmi_nand_data *this,
-			struct gpmi_nfc_hardware_timing *hw)
+static void gpmi_nfc_compute_timings(struct gpmi_nand_data *this,
+				     const struct nand_sdr_timings *sdr)
 {
-	struct resources *r = &this->resources;
-	unsigned long rate = clk_get_rate(r->clock[0]);
-	int mode = this->timing_mode;
-	int dll_threshold = this->devdata->max_chain_delay;
-	unsigned long delay;
-	unsigned long clk_period;
-	int t_rea;
-	int c = 4;
-	int t_rp;
-	int rp;
+	struct gpmi_nfc_hardware_timing *hw = &this->hw;
+	unsigned int dll_threshold_ps = this->devdata->max_chain_delay;
+	unsigned int period_ps, reference_period_ps;
+	unsigned int data_setup_cycles, data_hold_cycles, addr_setup_cycles;
+	unsigned int tRP_ps;
+	bool use_half_period;
+	int sample_delay_ps, sample_delay_factor;
+	u16 busy_timeout_cycles;
+	u8 wrn_dly_sel;
+
+	if (sdr->tRC_min >= 30000) {
+		/* ONFI non-EDO modes [0-3] */
+		hw->clk_rate = 22000000;
+		wrn_dly_sel = BV_GPMI_CTRL1_WRN_DLY_SEL_4_TO_8NS;
+	} else if (sdr->tRC_min >= 25000) {
+		/* ONFI EDO mode 4 */
+		hw->clk_rate = 80000000;
+		wrn_dly_sel = BV_GPMI_CTRL1_WRN_DLY_SEL_NO_DELAY;
+	} else {
+		/* ONFI EDO mode 5 */
+		hw->clk_rate = 100000000;
+		wrn_dly_sel = BV_GPMI_CTRL1_WRN_DLY_SEL_NO_DELAY;
+	}
 
-	/*
-	 * [1] for GPMI_HW_GPMI_TIMING0:
-	 *     The async mode requires 40MHz for mode 4, 50MHz for mode 5.
-	 *     The GPMI can support 100MHz at most. So if we want to
-	 *     get the 40MHz or 50MHz, we have to set DS=1, DH=1.
-	 *     Set the ADDRESS_SETUP to 0 in mode 4.
-	 */
-	hw->data_setup_in_cycles = 1;
-	hw->data_hold_in_cycles = 1;
-	hw->address_setup_in_cycles = ((mode == 5) ? 1 : 0);
+	/* SDR core timings are given in picoseconds */
+	period_ps = div_u64((u64)NSEC_PER_SEC * 1000, hw->clk_rate);
 
-	/* [2] for GPMI_HW_GPMI_TIMING1 */
-	hw->device_busy_timeout = 0x9000;
+	addr_setup_cycles = TO_CYCLES(sdr->tALS_min, period_ps);
+	data_setup_cycles = TO_CYCLES(sdr->tDS_min, period_ps);
+	data_hold_cycles = TO_CYCLES(sdr->tDH_min, period_ps);
+	busy_timeout_cycles = TO_CYCLES(sdr->tWB_max + sdr->tR_max, period_ps);
 
-	/* [3] for GPMI_HW_GPMI_CTRL1 */
-	hw->wrn_dly_sel = BV_GPMI_CTRL1_WRN_DLY_SEL_NO_DELAY;
+	hw->timing0 = BF_GPMI_TIMING0_ADDRESS_SETUP(addr_setup_cycles) |
+		      BF_GPMI_TIMING0_DATA_HOLD(data_hold_cycles) |
+		      BF_GPMI_TIMING0_DATA_SETUP(data_setup_cycles);
+	hw->timing1 = BF_GPMI_TIMING1_BUSY_TIMEOUT(busy_timeout_cycles * 4096);
 
 	/*
-	 * Enlarge 10 times for the numerator and denominator in {3}.
-	 * This make us to get more accurate result.
+	 * Derive NFC ideal delay from {3}:
+	 *
+	 *                     (tREA + 4000 - tRP) * 8
+	 *         RDN_DELAY = -----------------------
+	 *                                RP
 	 */
-	clk_period = NSEC_PER_SEC / (rate / 10);
-	dll_threshold *= 10;
-	t_rea = ((mode == 5) ? 16 : 20) * 10;
-	c *= 10;
-
-	t_rp = clk_period * 1; /* DATA_SETUP is 1 */
-
-	if (clk_period > dll_threshold) {
-		hw->use_half_periods = 1;
-		rp = clk_period / 2;
+	if (period_ps > dll_threshold_ps) {
+		use_half_period = true;
+		reference_period_ps = period_ps / 2;
 	} else {
-		hw->use_half_periods = 0;
-		rp = clk_period;
+		use_half_period = false;
+		reference_period_ps = period_ps;
 	}
 
-	/*
-	 * Multiply the numerator with 10, we could do a round off:
-	 *      7.8 round up to 8; 7.4 round down to 7.
-	 */
-	delay  = (((t_rea + c - t_rp) * 8) * 10) / rp;
-	delay = (delay + 5) / 10;
-
-	hw->sample_delay_factor = delay;
-}
-
-static int enable_edo_mode(struct gpmi_nand_data *this, int mode)
-{
-	struct resources  *r = &this->resources;
-	struct nand_chip *nand = &this->nand;
-	struct mtd_info	 *mtd = nand_to_mtd(nand);
-	uint8_t *feature;
-	unsigned long rate;
-	int ret;
-
-	feature = kzalloc(ONFI_SUBFEATURE_PARAM_LEN, GFP_KERNEL);
-	if (!feature)
-		return -ENOMEM;
-
-	nand->select_chip(mtd, 0);
-
-	/* [1] send SET FEATURE command to NAND */
-	feature[0] = mode;
-	ret = nand->onfi_set_features(mtd, nand,
-				ONFI_FEATURE_ADDR_TIMING_MODE, feature);
-	if (ret)
-		goto err_out;
-
-	/* [2] send GET FEATURE command to double-check the timing mode */
-	memset(feature, 0, ONFI_SUBFEATURE_PARAM_LEN);
-	ret = nand->onfi_get_features(mtd, nand,
-				ONFI_FEATURE_ADDR_TIMING_MODE, feature);
-	if (ret || feature[0] != mode)
-		goto err_out;
-
-	nand->select_chip(mtd, -1);
-
-	/* [3] set the main IO clock, 100MHz for mode 5, 80MHz for mode 4. */
-	rate = (mode == 5) ? 100000000 : 80000000;
-	clk_set_rate(r->clock[0], rate);
-
-	/* Let the gpmi_begin() re-compute the timing again. */
-	this->flags &= ~GPMI_TIMING_INIT_OK;
-
-	this->flags |= GPMI_ASYNC_EDO_ENABLED;
-	this->timing_mode = mode;
-	kfree(feature);
-	dev_info(this->dev, "enable the asynchronous EDO mode %d\n", mode);
-	return 0;
-
-err_out:
-	nand->select_chip(mtd, -1);
-	kfree(feature);
-	dev_err(this->dev, "mode:%d ,failed in set feature.\n", mode);
-	return -EINVAL;
-}
-
-int gpmi_extra_init(struct gpmi_nand_data *this)
-{
-	struct nand_chip *chip = &this->nand;
-
-	/* Enable the asynchronous EDO feature. */
-	if (GPMI_IS_MX6(this) && chip->onfi_version) {
-		int mode = onfi_get_async_timing_mode(chip);
-
-		/* We only support the timing mode 4 and mode 5. */
-		if (mode & ONFI_TIMING_MODE_5)
-			mode = 5;
-		else if (mode & ONFI_TIMING_MODE_4)
-			mode = 4;
-		else
-			return 0;
+	tRP_ps = data_setup_cycles * period_ps;
+	sample_delay_ps = (sdr->tREA_max + 4000 - tRP_ps) * 8;
+	if (sample_delay_ps > 0)
+		sample_delay_factor = sample_delay_ps / reference_period_ps;
+	else
+		sample_delay_factor = 0;
 
-		return enable_edo_mode(this, mode);
-	}
-	return 0;
+	hw->ctrl1n = BF_GPMI_CTRL1_WRN_DLY_SEL(wrn_dly_sel);
+	if (sample_delay_factor)
+		hw->ctrl1n |= BF_GPMI_CTRL1_RDN_DELAY(sample_delay_factor) |
+			      BM_GPMI_CTRL1_DLL_ENABLE |
+			      (use_half_period ? BM_GPMI_CTRL1_HALF_PERIOD : 0);
 }
 
-/* Begin the I/O */
-void gpmi_begin(struct gpmi_nand_data *this)
+void gpmi_nfc_apply_timings(struct gpmi_nand_data *this)
 {
+	struct gpmi_nfc_hardware_timing *hw = &this->hw;
 	struct resources *r = &this->resources;
 	void __iomem *gpmi_regs = r->gpmi_regs;
-	unsigned int   clock_period_in_ns;
-	uint32_t       reg;
-	unsigned int   dll_wait_time_in_us;
-	struct gpmi_nfc_hardware_timing  hw;
-	int ret;
-
-	/* Enable the clock. */
-	ret = gpmi_enable_clk(this);
-	if (ret) {
-		dev_err(this->dev, "We failed in enable the clk\n");
-		goto err_out;
-	}
-
-	/* Only initialize the timing once */
-	if (this->flags & GPMI_TIMING_INIT_OK)
-		return;
-	this->flags |= GPMI_TIMING_INIT_OK;
+	unsigned int dll_wait_time_us;
 
-	if (this->flags & GPMI_ASYNC_EDO_ENABLED)
-		gpmi_compute_edo_timing(this, &hw);
-	else
-		gpmi_nfc_compute_hardware_timing(this, &hw);
-
-	/* [1] Set HW_GPMI_TIMING0 */
-	reg = BF_GPMI_TIMING0_ADDRESS_SETUP(hw.address_setup_in_cycles) |
-		BF_GPMI_TIMING0_DATA_HOLD(hw.data_hold_in_cycles)         |
-		BF_GPMI_TIMING0_DATA_SETUP(hw.data_setup_in_cycles);
-
-	writel(reg, gpmi_regs + HW_GPMI_TIMING0);
-
-	/* [2] Set HW_GPMI_TIMING1 */
-	writel(BF_GPMI_TIMING1_BUSY_TIMEOUT(hw.device_busy_timeout),
-		gpmi_regs + HW_GPMI_TIMING1);
+	clk_set_rate(r->clock[0], hw->clk_rate);
 
-	/* [3] The following code is to set the HW_GPMI_CTRL1. */
+	writel(hw->timing0, gpmi_regs + HW_GPMI_TIMING0);
+	writel(hw->timing1, gpmi_regs + HW_GPMI_TIMING1);
 
-	/* Set the WRN_DLY_SEL */
-	writel(BM_GPMI_CTRL1_WRN_DLY_SEL, gpmi_regs + HW_GPMI_CTRL1_CLR);
-	writel(BF_GPMI_CTRL1_WRN_DLY_SEL(hw.wrn_dly_sel),
-					gpmi_regs + HW_GPMI_CTRL1_SET);
-
-	/* DLL_ENABLE must be set to 0 when setting RDN_DELAY or HALF_PERIOD. */
-	writel(BM_GPMI_CTRL1_DLL_ENABLE, gpmi_regs + HW_GPMI_CTRL1_CLR);
-
-	/* Clear out the DLL control fields. */
-	reg = BM_GPMI_CTRL1_RDN_DELAY | BM_GPMI_CTRL1_HALF_PERIOD;
-	writel(reg, gpmi_regs + HW_GPMI_CTRL1_CLR);
+	/*
+	 * Clear several CTRL1 fields, DLL must be disabled when setting
+	 * RDN_DELAY or HALF_PERIOD.
+	 */
+	writel(BM_GPMI_CTRL1_CLEAR_MASK, gpmi_regs + HW_GPMI_CTRL1_CLR);
+	writel(hw->ctrl1n, gpmi_regs + HW_GPMI_CTRL1_SET);
 
-	/* If no sample delay is called for, return immediately. */
-	if (!hw.sample_delay_factor)
-		return;
+	/* Wait 64 clock cycles before using the GPMI after enabling the DLL */
+	dll_wait_time_us = USEC_PER_SEC / hw->clk_rate * 64;
+	if (!dll_wait_time_us)
+		dll_wait_time_us = 1;
 
-	/* Set RDN_DELAY or HALF_PERIOD. */
-	reg = ((hw.use_half_periods) ? BM_GPMI_CTRL1_HALF_PERIOD : 0)
-		| BF_GPMI_CTRL1_RDN_DELAY(hw.sample_delay_factor);
+	/* Wait for the DLL to settle. */
+	udelay(dll_wait_time_us);
+}
 
-	writel(reg, gpmi_regs + HW_GPMI_CTRL1_SET);
+int gpmi_setup_data_interface(struct mtd_info *mtd, int chipnr,
+			      const struct nand_data_interface *conf)
+{
+	struct nand_chip *chip = mtd_to_nand(mtd);
+	struct gpmi_nand_data *this = nand_get_controller_data(chip);
+	const struct nand_sdr_timings *sdr;
 
-	/* At last, we enable the DLL. */
-	writel(BM_GPMI_CTRL1_DLL_ENABLE, gpmi_regs + HW_GPMI_CTRL1_SET);
+	/* Retrieve required NAND timings */
+	sdr = nand_get_sdr_timings(conf);
+	if (IS_ERR(sdr))
+		return PTR_ERR(sdr);
 
-	/*
-	 * After we enable the GPMI DLL, we have to wait 64 clock cycles before
-	 * we can use the GPMI. Calculate the amount of time we need to wait,
-	 * in microseconds.
-	 */
-	clock_period_in_ns = NSEC_PER_SEC / clk_get_rate(r->clock[0]);
-	dll_wait_time_in_us = (clock_period_in_ns * 64) / 1000;
+	/* Only MX6 GPMI controller can reach EDO timings */
+	if (sdr->tRC_min <= 25000 && !GPMI_IS_MX6(this))
+		return -ENOTSUPP;
 
-	if (!dll_wait_time_in_us)
-		dll_wait_time_in_us = 1;
+	/* Stop here if this call was just a check */
+	if (chipnr < 0)
+		return 0;
 
-	/* Wait for the DLL to settle. */
-	udelay(dll_wait_time_in_us);
+	/* Do the actual derivation of the controller timings */
+	gpmi_nfc_compute_timings(this, sdr);
 
-err_out:
-	return;
-}
+	this->hw.must_apply_timings = true;
 
-void gpmi_end(struct gpmi_nand_data *this)
-{
-	gpmi_disable_clk(this);
+	return 0;
 }
 
 /* Clears a BCH interrupt. */
diff --git a/drivers/mtd/nand/gpmi-nand/gpmi-nand.c b/drivers/mtd/nand/raw/gpmi-nand/gpmi-nand.c
index 61fdd733492f..c2597c8107a0 100644
--- a/drivers/mtd/nand/gpmi-nand/gpmi-nand.c
+++ b/drivers/mtd/nand/raw/gpmi-nand/gpmi-nand.c
@@ -94,7 +94,7 @@ static const struct mtd_ooblayout_ops gpmi_ooblayout_ops = {
 static const struct gpmi_devdata gpmi_devdata_imx23 = {
 	.type = IS_MX23,
 	.bch_max_ecc_strength = 20,
-	.max_chain_delay = 16,
+	.max_chain_delay = 16000,
 	.clks = gpmi_clks_for_mx2x,
 	.clks_count = ARRAY_SIZE(gpmi_clks_for_mx2x),
 };
@@ -102,7 +102,7 @@ static const struct gpmi_devdata gpmi_devdata_imx23 = {
 static const struct gpmi_devdata gpmi_devdata_imx28 = {
 	.type = IS_MX28,
 	.bch_max_ecc_strength = 20,
-	.max_chain_delay = 16,
+	.max_chain_delay = 16000,
 	.clks = gpmi_clks_for_mx2x,
 	.clks_count = ARRAY_SIZE(gpmi_clks_for_mx2x),
 };
@@ -114,7 +114,7 @@ static const char * const gpmi_clks_for_mx6[] = {
 static const struct gpmi_devdata gpmi_devdata_imx6q = {
 	.type = IS_MX6Q,
 	.bch_max_ecc_strength = 40,
-	.max_chain_delay = 12,
+	.max_chain_delay = 12000,
 	.clks = gpmi_clks_for_mx6,
 	.clks_count = ARRAY_SIZE(gpmi_clks_for_mx6),
 };
@@ -122,7 +122,7 @@ static const struct gpmi_devdata gpmi_devdata_imx6q = {
 static const struct gpmi_devdata gpmi_devdata_imx6sx = {
 	.type = IS_MX6SX,
 	.bch_max_ecc_strength = 62,
-	.max_chain_delay = 12,
+	.max_chain_delay = 12000,
 	.clks = gpmi_clks_for_mx6,
 	.clks_count = ARRAY_SIZE(gpmi_clks_for_mx6),
 };
@@ -134,7 +134,7 @@ static const char * const gpmi_clks_for_mx7d[] = {
 static const struct gpmi_devdata gpmi_devdata_imx7d = {
 	.type = IS_MX7D,
 	.bch_max_ecc_strength = 62,
-	.max_chain_delay = 12,
+	.max_chain_delay = 12000,
 	.clks = gpmi_clks_for_mx7d,
 	.clks_count = ARRAY_SIZE(gpmi_clks_for_mx7d),
 };
@@ -695,34 +695,6 @@ static void release_resources(struct gpmi_nand_data *this)
 	release_dma_channels(this);
 }
 
-static int init_hardware(struct gpmi_nand_data *this)
-{
-	int ret;
-
-	/*
-	 * This structure contains the "safe" GPMI timing that should succeed
-	 * with any NAND Flash device
-	 * (although, with less-than-optimal performance).
-	 */
-	struct nand_timing  safe_timing = {
-		.data_setup_in_ns        = 80,
-		.data_hold_in_ns         = 60,
-		.address_setup_in_ns     = 25,
-		.gpmi_sample_delay_in_ns =  6,
-		.tREA_in_ns              = -1,
-		.tRLOH_in_ns             = -1,
-		.tRHOH_in_ns             = -1,
-	};
-
-	/* Initialize the hardwares. */
-	ret = gpmi_init(this);
-	if (ret)
-		return ret;
-
-	this->timing = safe_timing;
-	return 0;
-}
-
 static int read_page_prepare(struct gpmi_nand_data *this,
 			void *destination, unsigned length,
 			void *alt_virt, dma_addr_t alt_phys, unsigned alt_size,
@@ -938,11 +910,32 @@ static void gpmi_select_chip(struct mtd_info *mtd, int chipnr)
 {
 	struct nand_chip *chip = mtd_to_nand(mtd);
 	struct gpmi_nand_data *this = nand_get_controller_data(chip);
+	int ret;
 
-	if ((this->current_chip < 0) && (chipnr >= 0))
-		gpmi_begin(this);
-	else if ((this->current_chip >= 0) && (chipnr < 0))
-		gpmi_end(this);
+	/*
+	 * For power consumption matters, disable/enable the clock each time a
+	 * die is selected/unselected.
+	 */
+	if (this->current_chip < 0 && chipnr >= 0) {
+		ret = gpmi_enable_clk(this);
+		if (ret)
+			dev_err(this->dev, "Failed to enable the clock\n");
+	} else if (this->current_chip >= 0 && chipnr < 0) {
+		ret = gpmi_disable_clk(this);
+		if (ret)
+			dev_err(this->dev, "Failed to disable the clock\n");
+	}
+
+	/*
+	 * This driver currently supports only one NAND chip. Plus, dies share
+	 * the same configuration. So once timings have been applied on the
+	 * controller side, they will not change anymore. When the time will
+	 * come, the check on must_apply_timings will have to be dropped.
+	 */
+	if (chipnr >= 0 && this->hw.must_apply_timings) {
+		this->hw.must_apply_timings = false;
+		gpmi_nfc_apply_timings(this);
+	}
 
 	this->current_chip = chipnr;
 }
@@ -1955,14 +1948,6 @@ static int gpmi_init_last(struct gpmi_nand_data *this)
 		chip->options |= NAND_SUBPAGE_READ;
 	}
 
-	/*
-	 * Can we enable the extra features? such as EDO or Sync mode.
-	 *
-	 * We do not check the return value now. That's means if we fail in
-	 * enable the extra features, we still can run in the normal way.
-	 */
-	gpmi_extra_init(this);
-
 	return 0;
 }
 
@@ -1983,6 +1968,7 @@ static int gpmi_nand_init(struct gpmi_nand_data *this)
 	nand_set_controller_data(chip, this);
 	nand_set_flash_node(chip, this->pdev->dev.of_node);
 	chip->select_chip	= gpmi_select_chip;
+	chip->setup_data_interface = gpmi_setup_data_interface;
 	chip->cmd_ctrl		= gpmi_cmd_ctrl;
 	chip->dev_ready		= gpmi_dev_ready;
 	chip->read_byte		= gpmi_read_byte;
@@ -2093,7 +2079,7 @@ static int gpmi_nand_probe(struct platform_device *pdev)
 	if (ret)
 		goto exit_acquire_resources;
 
-	ret = init_hardware(this);
+	ret = gpmi_init(this);
 	if (ret)
 		goto exit_nfc_init;
 
@@ -2141,7 +2127,6 @@ static int gpmi_pm_resume(struct device *dev)
 		return ret;
 
 	/* re-init the GPMI registers */
-	this->flags &= ~GPMI_TIMING_INIT_OK;
 	ret = gpmi_init(this);
 	if (ret) {
 		dev_err(this->dev, "Error setting GPMI : %d\n", ret);
@@ -2155,9 +2140,6 @@ static int gpmi_pm_resume(struct device *dev)
 		return ret;
 	}
 
-	/* re-init others */
-	gpmi_extra_init(this);
-
 	return 0;
 }
 #endif /* CONFIG_PM_SLEEP */
diff --git a/drivers/mtd/nand/gpmi-nand/gpmi-nand.h b/drivers/mtd/nand/raw/gpmi-nand/gpmi-nand.h
index 06c1f993912c..62fde59b995f 100644
--- a/drivers/mtd/nand/gpmi-nand/gpmi-nand.h
+++ b/drivers/mtd/nand/raw/gpmi-nand/gpmi-nand.h
@@ -86,39 +86,6 @@ enum dma_ops_type {
 	DMA_FOR_WRITE_ECC_PAGE
 };
 
-/**
- * struct nand_timing - Fundamental timing attributes for NAND.
- * @data_setup_in_ns:         The data setup time, in nanoseconds. Usually the
- *                            maximum of tDS and tWP. A negative value
- *                            indicates this characteristic isn't known.
- * @data_hold_in_ns:          The data hold time, in nanoseconds. Usually the
- *                            maximum of tDH, tWH and tREH. A negative value
- *                            indicates this characteristic isn't known.
- * @address_setup_in_ns:      The address setup time, in nanoseconds. Usually
- *                            the maximum of tCLS, tCS and tALS. A negative
- *                            value indicates this characteristic isn't known.
- * @gpmi_sample_delay_in_ns:  A GPMI-specific timing parameter. A negative value
- *                            indicates this characteristic isn't known.
- * @tREA_in_ns:               tREA, in nanoseconds, from the data sheet. A
- *                            negative value indicates this characteristic isn't
- *                            known.
- * @tRLOH_in_ns:              tRLOH, in nanoseconds, from the data sheet. A
- *                            negative value indicates this characteristic isn't
- *                            known.
- * @tRHOH_in_ns:              tRHOH, in nanoseconds, from the data sheet. A
- *                            negative value indicates this characteristic isn't
- *                            known.
- */
-struct nand_timing {
-	int8_t  data_setup_in_ns;
-	int8_t  data_hold_in_ns;
-	int8_t  address_setup_in_ns;
-	int8_t  gpmi_sample_delay_in_ns;
-	int8_t  tREA_in_ns;
-	int8_t  tRLOH_in_ns;
-	int8_t  tRHOH_in_ns;
-};
-
 enum gpmi_type {
 	IS_MX23,
 	IS_MX28,
@@ -135,11 +102,27 @@ struct gpmi_devdata {
 	const int clks_count;
 };
 
+/**
+ * struct gpmi_nfc_hardware_timing - GPMI hardware timing parameters.
+ * @must_apply_timings:        Whether controller timings have already been
+ *                             applied or not (useful only while there is
+ *                             support for only one chip select)
+ * @clk_rate:                  The clock rate that must be used to derive the
+ *                             following parameters
+ * @timing0:                   HW_GPMI_TIMING0 register
+ * @timing1:                   HW_GPMI_TIMING1 register
+ * @ctrl1n:                    HW_GPMI_CTRL1n register
+ */
+struct gpmi_nfc_hardware_timing {
+	bool must_apply_timings;
+	unsigned long int clk_rate;
+	u32 timing0;
+	u32 timing1;
+	u32 ctrl1n;
+};
+
 struct gpmi_nand_data {
-	/* flags */
-#define GPMI_ASYNC_EDO_ENABLED	(1 << 0)
-#define GPMI_TIMING_INIT_OK	(1 << 1)
-	int			flags;
+	/* Devdata */
 	const struct gpmi_devdata *devdata;
 
 	/* System Interface */
@@ -150,8 +133,7 @@ struct gpmi_nand_data {
 	struct resources	resources;
 
 	/* Flash Hardware */
-	struct nand_timing	timing;
-	int			timing_mode;
+	struct gpmi_nfc_hardware_timing hw;
 
 	/* BCH */
 	struct bch_geometry	bch_geometry;
@@ -204,69 +186,6 @@ struct gpmi_nand_data {
 	void			*private;
 };
 
-/**
- * struct gpmi_nfc_hardware_timing - GPMI hardware timing parameters.
- * @data_setup_in_cycles:      The data setup time, in cycles.
- * @data_hold_in_cycles:       The data hold time, in cycles.
- * @address_setup_in_cycles:   The address setup time, in cycles.
- * @device_busy_timeout:       The timeout waiting for NAND Ready/Busy,
- *                             this value is the number of cycles multiplied
- *                             by 4096.
- * @use_half_periods:          Indicates the clock is running slowly, so the
- *                             NFC DLL should use half-periods.
- * @sample_delay_factor:       The sample delay factor.
- * @wrn_dly_sel:               The delay on the GPMI write strobe.
- */
-struct gpmi_nfc_hardware_timing {
-	/* for HW_GPMI_TIMING0 */
-	uint8_t  data_setup_in_cycles;
-	uint8_t  data_hold_in_cycles;
-	uint8_t  address_setup_in_cycles;
-
-	/* for HW_GPMI_TIMING1 */
-	uint16_t device_busy_timeout;
-#define GPMI_DEFAULT_BUSY_TIMEOUT	0x500 /* default busy timeout value.*/
-
-	/* for HW_GPMI_CTRL1 */
-	bool     use_half_periods;
-	uint8_t  sample_delay_factor;
-	uint8_t  wrn_dly_sel;
-};
-
-/**
- * struct timing_threshold - Timing threshold
- * @max_data_setup_cycles:       The maximum number of data setup cycles that
- *                               can be expressed in the hardware.
- * @internal_data_setup_in_ns:   The time, in ns, that the NFC hardware requires
- *                               for data read internal setup. In the Reference
- *                               Manual, see the chapter "High-Speed NAND
- *                               Timing" for more details.
- * @max_sample_delay_factor:     The maximum sample delay factor that can be
- *                               expressed in the hardware.
- * @max_dll_clock_period_in_ns:  The maximum period of the GPMI clock that the
- *                               sample delay DLL hardware can possibly work
- *                               with (the DLL is unusable with longer periods).
- *                               If the full-cycle period is greater than HALF
- *                               this value, the DLL must be configured to use
- *                               half-periods.
- * @max_dll_delay_in_ns:         The maximum amount of delay, in ns, that the
- *                               DLL can implement.
- * @clock_frequency_in_hz:       The clock frequency, in Hz, during the current
- *                               I/O transaction. If no I/O transaction is in
- *                               progress, this is the clock frequency during
- *                               the most recent I/O transaction.
- */
-struct timing_threshold {
-	const unsigned int      max_chip_count;
-	const unsigned int      max_data_setup_cycles;
-	const unsigned int      internal_data_setup_in_ns;
-	const unsigned int      max_sample_delay_factor;
-	const unsigned int      max_dll_clock_period_in_ns;
-	const unsigned int      max_dll_delay_in_ns;
-	unsigned long           clock_frequency_in_hz;
-
-};
-
 /* Common Services */
 int common_nfc_set_geometry(struct gpmi_nand_data *);
 struct dma_chan *get_dma_chan(struct gpmi_nand_data *);
@@ -279,14 +198,16 @@ int start_dma_with_bch_irq(struct gpmi_nand_data *,
 
 /* GPMI-NAND helper function library */
 int gpmi_init(struct gpmi_nand_data *);
-int gpmi_extra_init(struct gpmi_nand_data *);
 void gpmi_clear_bch(struct gpmi_nand_data *);
 void gpmi_dump_info(struct gpmi_nand_data *);
 int bch_set_geometry(struct gpmi_nand_data *);
 int gpmi_is_ready(struct gpmi_nand_data *, unsigned chip);
 int gpmi_send_command(struct gpmi_nand_data *);
-void gpmi_begin(struct gpmi_nand_data *);
-void gpmi_end(struct gpmi_nand_data *);
+int gpmi_enable_clk(struct gpmi_nand_data *this);
+int gpmi_disable_clk(struct gpmi_nand_data *this);
+int gpmi_setup_data_interface(struct mtd_info *mtd, int chipnr,
+			      const struct nand_data_interface *conf);
+void gpmi_nfc_apply_timings(struct gpmi_nand_data *this);
 int gpmi_read_data(struct gpmi_nand_data *);
 int gpmi_send_data(struct gpmi_nand_data *);
 int gpmi_send_page(struct gpmi_nand_data *,
diff --git a/drivers/mtd/nand/gpmi-nand/gpmi-regs.h b/drivers/mtd/nand/raw/gpmi-nand/gpmi-regs.h
index 82114cdc8330..d92bf32221ca 100644
--- a/drivers/mtd/nand/gpmi-nand/gpmi-regs.h
+++ b/drivers/mtd/nand/raw/gpmi-nand/gpmi-regs.h
@@ -147,6 +147,11 @@
 
 #define BM_GPMI_CTRL1_GPMI_MODE				(1 << 0)
 
+#define BM_GPMI_CTRL1_CLEAR_MASK (BM_GPMI_CTRL1_WRN_DLY_SEL | \
+				  BM_GPMI_CTRL1_DLL_ENABLE |  \
+				  BM_GPMI_CTRL1_RDN_DELAY |   \
+				  BM_GPMI_CTRL1_HALF_PERIOD)
+
 #define HW_GPMI_TIMING0					0x00000070
 
 #define BP_GPMI_TIMING0_ADDRESS_SETUP			16
diff --git a/drivers/mtd/nand/hisi504_nand.c b/drivers/mtd/nand/raw/hisi504_nand.c
index cb862793ab6d..27558a67fa41 100644
--- a/drivers/mtd/nand/hisi504_nand.c
+++ b/drivers/mtd/nand/raw/hisi504_nand.c
@@ -762,8 +762,8 @@ static int hisi_nfc_probe(struct platform_device *pdev)
 	chip->write_buf		= hisi_nfc_write_buf;
 	chip->read_buf		= hisi_nfc_read_buf;
 	chip->chip_delay	= HINFC504_CHIP_DELAY;
-	chip->onfi_set_features	= nand_onfi_get_set_features_notsupp;
-	chip->onfi_get_features	= nand_onfi_get_set_features_notsupp;
+	chip->set_features	= nand_get_set_features_notsupp;
+	chip->get_features	= nand_get_set_features_notsupp;
 
 	hisi_nfc_host_init(host);
 
diff --git a/drivers/mtd/nand/jz4740_nand.c b/drivers/mtd/nand/raw/jz4740_nand.c
index 613b00a9604b..613b00a9604b 100644
--- a/drivers/mtd/nand/jz4740_nand.c
+++ b/drivers/mtd/nand/raw/jz4740_nand.c
diff --git a/drivers/mtd/nand/jz4780_bch.c b/drivers/mtd/nand/raw/jz4780_bch.c
index 731c6051d91e..731c6051d91e 100644
--- a/drivers/mtd/nand/jz4780_bch.c
+++ b/drivers/mtd/nand/raw/jz4780_bch.c
diff --git a/drivers/mtd/nand/jz4780_bch.h b/drivers/mtd/nand/raw/jz4780_bch.h
index bf4718088a3a..bf4718088a3a 100644
--- a/drivers/mtd/nand/jz4780_bch.h
+++ b/drivers/mtd/nand/raw/jz4780_bch.h
diff --git a/drivers/mtd/nand/jz4780_nand.c b/drivers/mtd/nand/raw/jz4780_nand.c
index e69f6ae4c539..e69f6ae4c539 100644
--- a/drivers/mtd/nand/jz4780_nand.c
+++ b/drivers/mtd/nand/raw/jz4780_nand.c
diff --git a/drivers/mtd/nand/lpc32xx_mlc.c b/drivers/mtd/nand/raw/lpc32xx_mlc.c
index e357948a7505..e357948a7505 100644
--- a/drivers/mtd/nand/lpc32xx_mlc.c
+++ b/drivers/mtd/nand/raw/lpc32xx_mlc.c
diff --git a/drivers/mtd/nand/lpc32xx_slc.c b/drivers/mtd/nand/raw/lpc32xx_slc.c
index 5f7cc6da0a7f..5f7cc6da0a7f 100644
--- a/drivers/mtd/nand/lpc32xx_slc.c
+++ b/drivers/mtd/nand/raw/lpc32xx_slc.c
diff --git a/drivers/mtd/nand/marvell_nand.c b/drivers/mtd/nand/raw/marvell_nand.c
index 03805f9669da..10e953218948 100644
--- a/drivers/mtd/nand/marvell_nand.c
+++ b/drivers/mtd/nand/raw/marvell_nand.c
@@ -307,7 +307,8 @@ struct marvell_nfc_caps {
  * @controller:		Base controller structure
  * @dev:		Parent device (used to print error messages)
  * @regs:		NAND controller registers
- * @ecc_clk:		ECC block clock, two times the NAND controller clock
+ * @core_clk:		Core clock
+ * @reg_clk:		Regiters clock
  * @complete:		Completion object to wait for NAND controller events
  * @assigned_cs:	Bitmask describing already assigned CS lines
  * @chips:		List containing all the NAND chips attached to
@@ -320,7 +321,8 @@ struct marvell_nfc {
 	struct nand_hw_control controller;
 	struct device *dev;
 	void __iomem *regs;
-	struct clk *ecc_clk;
+	struct clk *core_clk;
+	struct clk *reg_clk;
 	struct completion complete;
 	unsigned long assigned_cs;
 	struct list_head chips;
@@ -379,6 +381,8 @@ struct marvell_nfc_timings {
  * return the number of clock periods.
  */
 #define TO_CYCLES(ps, period_ns) (DIV_ROUND_UP(ps / 1000, period_ns))
+#define TO_CYCLES64(ps, period_ns) (DIV_ROUND_UP_ULL(div_u64(ps, 1000), \
+						     period_ns))
 
 /**
  * NAND driver structure filled during the parsing of the ->exec_op() subop
@@ -2189,7 +2193,7 @@ static int marvell_nfc_setup_data_interface(struct mtd_info *mtd, int chipnr,
 	struct nand_chip *chip = mtd_to_nand(mtd);
 	struct marvell_nand_chip *marvell_nand = to_marvell_nand(chip);
 	struct marvell_nfc *nfc = to_marvell_nfc(chip->controller);
-	unsigned int period_ns = 1000000000 / clk_get_rate(nfc->ecc_clk) * 2;
+	unsigned int period_ns = 1000000000 / clk_get_rate(nfc->core_clk) * 2;
 	const struct nand_sdr_timings *sdr;
 	struct marvell_nfc_timings nfc_tmg;
 	int read_delay;
@@ -2236,8 +2240,20 @@ static int marvell_nfc_setup_data_interface(struct mtd_info *mtd, int chipnr,
 	nfc_tmg.tRHW = TO_CYCLES(max_t(int, sdr->tRHW_min, sdr->tCCS_min),
 				 period_ns);
 
-	/* Use WAIT_MODE (wait for RB line) instead of only relying on delays */
-	nfc_tmg.tR = TO_CYCLES(sdr->tWB_max, period_ns);
+	/*
+	 * NFCv2: Use WAIT_MODE (wait for RB line), do not rely only on delays.
+	 * NFCv1: No WAIT_MODE, tR must be maximal.
+	 */
+	if (nfc->caps->is_nfcv2) {
+		nfc_tmg.tR = TO_CYCLES(sdr->tWB_max, period_ns);
+	} else {
+		nfc_tmg.tR = TO_CYCLES64(sdr->tWB_max + sdr->tR_max,
+					 period_ns);
+		if (nfc_tmg.tR + 3 > nfc_tmg.tCH)
+			nfc_tmg.tR = nfc_tmg.tCH - 3;
+		else
+			nfc_tmg.tR = 0;
+	}
 
 	if (chipnr < 0)
 		return 0;
@@ -2249,18 +2265,24 @@ static int marvell_nfc_setup_data_interface(struct mtd_info *mtd, int chipnr,
 		NDTR0_TWP(nfc_tmg.tWP) |
 		NDTR0_TWH(nfc_tmg.tWH) |
 		NDTR0_TCS(nfc_tmg.tCS) |
-		NDTR0_TCH(nfc_tmg.tCH) |
-		NDTR0_RD_CNT_DEL(read_delay) |
-		NDTR0_SELCNTR |
-		NDTR0_TADL(nfc_tmg.tADL);
+		NDTR0_TCH(nfc_tmg.tCH);
 
 	marvell_nand->ndtr1 =
 		NDTR1_TAR(nfc_tmg.tAR) |
 		NDTR1_TWHR(nfc_tmg.tWHR) |
-		NDTR1_TRHW(nfc_tmg.tRHW) |
-		NDTR1_WAIT_MODE |
 		NDTR1_TR(nfc_tmg.tR);
 
+	if (nfc->caps->is_nfcv2) {
+		marvell_nand->ndtr0 |=
+			NDTR0_RD_CNT_DEL(read_delay) |
+			NDTR0_SELCNTR |
+			NDTR0_TADL(nfc_tmg.tADL);
+
+		marvell_nand->ndtr1 |=
+			NDTR1_TRHW(nfc_tmg.tRHW) |
+			NDTR1_WAIT_MODE;
+	}
+
 	return 0;
 }
 
@@ -2395,8 +2417,7 @@ static int marvell_nand_chip_init(struct device *dev, struct marvell_nfc *nfc,
 
 	chip->exec_op = marvell_nfc_exec_op;
 	chip->select_chip = marvell_nfc_select_chip;
-	if (nfc->caps->is_nfcv2 &&
-	    !of_property_read_bool(np, "marvell,nand-keep-config"))
+	if (!of_property_read_bool(np, "marvell,nand-keep-config"))
 		chip->setup_data_interface = marvell_nfc_setup_data_interface;
 
 	mtd = nand_to_mtd(chip);
@@ -2738,20 +2759,37 @@ static int marvell_nfc_probe(struct platform_device *pdev)
 		return irq;
 	}
 
-	nfc->ecc_clk = devm_clk_get(&pdev->dev, NULL);
-	if (IS_ERR(nfc->ecc_clk))
-		return PTR_ERR(nfc->ecc_clk);
+	nfc->core_clk = devm_clk_get(&pdev->dev, "core");
 
-	ret = clk_prepare_enable(nfc->ecc_clk);
+	/* Managed the legacy case (when the first clock was not named) */
+	if (nfc->core_clk == ERR_PTR(-ENOENT))
+		nfc->core_clk = devm_clk_get(&pdev->dev, NULL);
+
+	if (IS_ERR(nfc->core_clk))
+		return PTR_ERR(nfc->core_clk);
+
+	ret = clk_prepare_enable(nfc->core_clk);
 	if (ret)
 		return ret;
 
+	nfc->reg_clk = devm_clk_get(&pdev->dev, "reg");
+	if (PTR_ERR(nfc->reg_clk) != -ENOENT) {
+		if (!IS_ERR(nfc->reg_clk)) {
+			ret = clk_prepare_enable(nfc->reg_clk);
+			if (ret)
+				goto unprepare_core_clk;
+		} else {
+			ret = PTR_ERR(nfc->reg_clk);
+			goto unprepare_core_clk;
+		}
+	}
+
 	marvell_nfc_disable_int(nfc, NDCR_ALL_INT);
 	marvell_nfc_clear_int(nfc, NDCR_ALL_INT);
 	ret = devm_request_irq(dev, irq, marvell_nfc_isr,
 			       0, "marvell-nfc", nfc);
 	if (ret)
-		goto unprepare_clk;
+		goto unprepare_reg_clk;
 
 	/* Get NAND controller capabilities */
 	if (pdev->id_entry)
@@ -2762,24 +2800,26 @@ static int marvell_nfc_probe(struct platform_device *pdev)
 	if (!nfc->caps) {
 		dev_err(dev, "Could not retrieve NFC caps\n");
 		ret = -EINVAL;
-		goto unprepare_clk;
+		goto unprepare_reg_clk;
 	}
 
 	/* Init the controller and then probe the chips */
 	ret = marvell_nfc_init(nfc);
 	if (ret)
-		goto unprepare_clk;
+		goto unprepare_reg_clk;
 
 	platform_set_drvdata(pdev, nfc);
 
 	ret = marvell_nand_chips_init(dev, nfc);
 	if (ret)
-		goto unprepare_clk;
+		goto unprepare_reg_clk;
 
 	return 0;
 
-unprepare_clk:
-	clk_disable_unprepare(nfc->ecc_clk);
+unprepare_reg_clk:
+	clk_disable_unprepare(nfc->reg_clk);
+unprepare_core_clk:
+	clk_disable_unprepare(nfc->core_clk);
 
 	return ret;
 }
@@ -2795,7 +2835,8 @@ static int marvell_nfc_remove(struct platform_device *pdev)
 		dma_release_channel(nfc->dma_chan);
 	}
 
-	clk_disable_unprepare(nfc->ecc_clk);
+	clk_disable_unprepare(nfc->reg_clk);
+	clk_disable_unprepare(nfc->core_clk);
 
 	return 0;
 }
diff --git a/drivers/mtd/nand/mpc5121_nfc.c b/drivers/mtd/nand/raw/mpc5121_nfc.c
index b6b97cc9fba6..6d1740d54e0d 100644
--- a/drivers/mtd/nand/mpc5121_nfc.c
+++ b/drivers/mtd/nand/raw/mpc5121_nfc.c
@@ -6,9 +6,8 @@
  * by OSADL membership fees in 2009;  for details see www.osadl.org.
  *
  * Based on original driver from Freescale Semiconductor
- * written by John Rigby <jrigby@freescale.com> on basis
- * of drivers/mtd/nand/mxc_nand.c. Reworked and extended
- * Piotr Ziecik <kosmo@semihalf.com>.
+ * written by John Rigby <jrigby@freescale.com> on basis of mxc_nand.c.
+ * Reworked and extended by Piotr Ziecik <kosmo@semihalf.com>.
  *
  * This program is free software; you can redistribute it and/or
  * modify it under the terms of the GNU General Public License
@@ -708,8 +707,8 @@ static int mpc5121_nfc_probe(struct platform_device *op)
 	chip->read_buf = mpc5121_nfc_read_buf;
 	chip->write_buf = mpc5121_nfc_write_buf;
 	chip->select_chip = mpc5121_nfc_select_chip;
-	chip->onfi_set_features	= nand_onfi_get_set_features_notsupp;
-	chip->onfi_get_features	= nand_onfi_get_set_features_notsupp;
+	chip->set_features	= nand_get_set_features_notsupp;
+	chip->get_features	= nand_get_set_features_notsupp;
 	chip->bbt_options = NAND_BBT_USE_FLASH;
 	chip->ecc.mode = NAND_ECC_SOFT;
 	chip->ecc.algo = NAND_ECC_HAMMING;
diff --git a/drivers/mtd/nand/mtk_ecc.c b/drivers/mtd/nand/raw/mtk_ecc.c
index 40d86a861a70..40d86a861a70 100644
--- a/drivers/mtd/nand/mtk_ecc.c
+++ b/drivers/mtd/nand/raw/mtk_ecc.c
diff --git a/drivers/mtd/nand/mtk_ecc.h b/drivers/mtd/nand/raw/mtk_ecc.h
index a455df080952..a455df080952 100644
--- a/drivers/mtd/nand/mtk_ecc.h
+++ b/drivers/mtd/nand/raw/mtk_ecc.h
diff --git a/drivers/mtd/nand/mtk_nand.c b/drivers/mtd/nand/raw/mtk_nand.c
index 6977da3a26aa..6977da3a26aa 100644
--- a/drivers/mtd/nand/mtk_nand.c
+++ b/drivers/mtd/nand/raw/mtk_nand.c
diff --git a/drivers/mtd/nand/mxc_nand.c b/drivers/mtd/nand/raw/mxc_nand.c
index f3be0b2a8869..45786e707b7b 100644
--- a/drivers/mtd/nand/mxc_nand.c
+++ b/drivers/mtd/nand/raw/mxc_nand.c
@@ -140,6 +140,8 @@ struct mxc_nand_host;
 
 struct mxc_nand_devtype_data {
 	void (*preset)(struct mtd_info *);
+	int (*read_page)(struct nand_chip *chip, void *buf, void *oob, bool ecc,
+			 int page);
 	void (*send_cmd)(struct mxc_nand_host *, uint16_t, int);
 	void (*send_addr)(struct mxc_nand_host *, uint16_t, int);
 	void (*send_page)(struct mtd_info *, unsigned int);
@@ -150,10 +152,9 @@ struct mxc_nand_devtype_data {
 	u32 (*get_ecc_status)(struct mxc_nand_host *);
 	const struct mtd_ooblayout_ops *ooblayout;
 	void (*select_chip)(struct mtd_info *mtd, int chip);
-	int (*correct_data)(struct mtd_info *mtd, u_char *dat,
-			u_char *read_ecc, u_char *calc_ecc);
 	int (*setup_data_interface)(struct mtd_info *mtd, int csline,
 				    const struct nand_data_interface *conf);
+	void (*enable_hwecc)(struct nand_chip *chip, bool enable);
 
 	/*
 	 * On i.MX21 the CONFIG2:INT bit cannot be read if interrupts are masked
@@ -252,6 +253,109 @@ static void memcpy16_toio(void __iomem *trg, const void *src, int size)
 		__raw_writew(*s++, t++);
 }
 
+/*
+ * The controller splits a page into data chunks of 512 bytes + partial oob.
+ * There are writesize / 512 such chunks, the size of the partial oob parts is
+ * oobsize / #chunks rounded down to a multiple of 2. The last oob chunk then
+ * contains additionally the byte lost by rounding (if any).
+ * This function handles the needed shuffling between host->data_buf (which
+ * holds a page in natural order, i.e. writesize bytes data + oobsize bytes
+ * spare) and the NFC buffer.
+ */
+static void copy_spare(struct mtd_info *mtd, bool bfrom, void *buf)
+{
+	struct nand_chip *this = mtd_to_nand(mtd);
+	struct mxc_nand_host *host = nand_get_controller_data(this);
+	u16 i, oob_chunk_size;
+	u16 num_chunks = mtd->writesize / 512;
+
+	u8 *d = buf;
+	u8 __iomem *s = host->spare0;
+	u16 sparebuf_size = host->devtype_data->spare_len;
+
+	/* size of oob chunk for all but possibly the last one */
+	oob_chunk_size = (host->used_oobsize / num_chunks) & ~1;
+
+	if (bfrom) {
+		for (i = 0; i < num_chunks - 1; i++)
+			memcpy16_fromio(d + i * oob_chunk_size,
+					s + i * sparebuf_size,
+					oob_chunk_size);
+
+		/* the last chunk */
+		memcpy16_fromio(d + i * oob_chunk_size,
+				s + i * sparebuf_size,
+				host->used_oobsize - i * oob_chunk_size);
+	} else {
+		for (i = 0; i < num_chunks - 1; i++)
+			memcpy16_toio(&s[i * sparebuf_size],
+				      &d[i * oob_chunk_size],
+				      oob_chunk_size);
+
+		/* the last chunk */
+		memcpy16_toio(&s[i * sparebuf_size],
+			      &d[i * oob_chunk_size],
+			      host->used_oobsize - i * oob_chunk_size);
+	}
+}
+
+/*
+ * MXC NANDFC can only perform full page+spare or spare-only read/write.  When
+ * the upper layers perform a read/write buf operation, the saved column address
+ * is used to index into the full page. So usually this function is called with
+ * column == 0 (unless no column cycle is needed indicated by column == -1)
+ */
+static void mxc_do_addr_cycle(struct mtd_info *mtd, int column, int page_addr)
+{
+	struct nand_chip *nand_chip = mtd_to_nand(mtd);
+	struct mxc_nand_host *host = nand_get_controller_data(nand_chip);
+
+	/* Write out column address, if necessary */
+	if (column != -1) {
+		host->devtype_data->send_addr(host, column & 0xff,
+					      page_addr == -1);
+		if (mtd->writesize > 512)
+			/* another col addr cycle for 2k page */
+			host->devtype_data->send_addr(host,
+						      (column >> 8) & 0xff,
+						      false);
+	}
+
+	/* Write out page address, if necessary */
+	if (page_addr != -1) {
+		/* paddr_0 - p_addr_7 */
+		host->devtype_data->send_addr(host, (page_addr & 0xff), false);
+
+		if (mtd->writesize > 512) {
+			if (mtd->size >= 0x10000000) {
+				/* paddr_8 - paddr_15 */
+				host->devtype_data->send_addr(host,
+						(page_addr >> 8) & 0xff,
+						false);
+				host->devtype_data->send_addr(host,
+						(page_addr >> 16) & 0xff,
+						true);
+			} else
+				/* paddr_8 - paddr_15 */
+				host->devtype_data->send_addr(host,
+						(page_addr >> 8) & 0xff, true);
+		} else {
+			if (nand_chip->options & NAND_ROW_ADDR_3) {
+				/* paddr_8 - paddr_15 */
+				host->devtype_data->send_addr(host,
+						(page_addr >> 8) & 0xff,
+						false);
+				host->devtype_data->send_addr(host,
+						(page_addr >> 16) & 0xff,
+						true);
+			} else
+				/* paddr_8 - paddr_15 */
+				host->devtype_data->send_addr(host,
+						(page_addr >> 8) & 0xff, true);
+		}
+	}
+}
+
 static int check_int_v3(struct mxc_nand_host *host)
 {
 	uint32_t tmp;
@@ -575,6 +679,42 @@ static uint16_t get_dev_status_v1_v2(struct mxc_nand_host *host)
 	return ret;
 }
 
+static void mxc_nand_enable_hwecc_v1_v2(struct nand_chip *chip, bool enable)
+{
+	struct mxc_nand_host *host = nand_get_controller_data(chip);
+	uint16_t config1;
+
+	if (chip->ecc.mode != NAND_ECC_HW)
+		return;
+
+	config1 = readw(NFC_V1_V2_CONFIG1);
+
+	if (enable)
+		config1 |= NFC_V1_V2_CONFIG1_ECC_EN;
+	else
+		config1 &= ~NFC_V1_V2_CONFIG1_ECC_EN;
+
+	writew(config1, NFC_V1_V2_CONFIG1);
+}
+
+static void mxc_nand_enable_hwecc_v3(struct nand_chip *chip, bool enable)
+{
+	struct mxc_nand_host *host = nand_get_controller_data(chip);
+	uint32_t config2;
+
+	if (chip->ecc.mode != NAND_ECC_HW)
+		return;
+
+	config2 = readl(NFC_V3_CONFIG2);
+
+	if (enable)
+		config2 |= NFC_V3_CONFIG2_ECC_EN;
+	else
+		config2 &= ~NFC_V3_CONFIG2_ECC_EN;
+
+	writel(config2, NFC_V3_CONFIG2);
+}
+
 /* This functions is used by upper layer to checks if device is ready */
 static int mxc_nand_dev_ready(struct mtd_info *mtd)
 {
@@ -585,45 +725,90 @@ static int mxc_nand_dev_ready(struct mtd_info *mtd)
 	return 1;
 }
 
-static void mxc_nand_enable_hwecc(struct mtd_info *mtd, int mode)
+static int mxc_nand_read_page_v1(struct nand_chip *chip, void *buf, void *oob,
+				 bool ecc, int page)
 {
-	/*
-	 * If HW ECC is enabled, we turn it on during init. There is
-	 * no need to enable again here.
-	 */
-}
+	struct mtd_info *mtd = nand_to_mtd(chip);
+	struct mxc_nand_host *host = nand_get_controller_data(chip);
+	unsigned int bitflips_corrected = 0;
+	int no_subpages;
+	int i;
 
-static int mxc_nand_correct_data_v1(struct mtd_info *mtd, u_char *dat,
-				 u_char *read_ecc, u_char *calc_ecc)
-{
-	struct nand_chip *nand_chip = mtd_to_nand(mtd);
-	struct mxc_nand_host *host = nand_get_controller_data(nand_chip);
+	host->devtype_data->enable_hwecc(chip, ecc);
 
-	/*
-	 * 1-Bit errors are automatically corrected in HW.  No need for
-	 * additional correction.  2-Bit errors cannot be corrected by
-	 * HW ECC, so we need to return failure
-	 */
-	uint16_t ecc_status = get_ecc_status_v1(host);
+	host->devtype_data->send_cmd(host, NAND_CMD_READ0, false);
+	mxc_do_addr_cycle(mtd, 0, page);
+
+	if (mtd->writesize > 512)
+		host->devtype_data->send_cmd(host, NAND_CMD_READSTART, true);
+
+	no_subpages = mtd->writesize >> 9;
+
+	for (i = 0; i < no_subpages; i++) {
+		uint16_t ecc_stats;
+
+		/* NANDFC buffer 0 is used for page read/write */
+		writew((host->active_cs << 4) | i, NFC_V1_V2_BUF_ADDR);
+
+		writew(NFC_OUTPUT, NFC_V1_V2_CONFIG2);
+
+		/* Wait for operation to complete */
+		wait_op_done(host, true);
+
+		ecc_stats = get_ecc_status_v1(host);
+
+		ecc_stats >>= 2;
 
-	if (((ecc_status & 0x3) == 2) || ((ecc_status >> 2) == 2)) {
-		dev_dbg(host->dev, "HWECC uncorrectable 2-bit ECC error\n");
-		return -EBADMSG;
+		if (buf && ecc) {
+			switch (ecc_stats & 0x3) {
+			case 0:
+			default:
+				break;
+			case 1:
+				mtd->ecc_stats.corrected++;
+				bitflips_corrected = 1;
+				break;
+			case 2:
+				mtd->ecc_stats.failed++;
+				break;
+			}
+		}
 	}
 
-	return 0;
+	if (buf)
+		memcpy32_fromio(buf, host->main_area0, mtd->writesize);
+	if (oob)
+		copy_spare(mtd, true, oob);
+
+	return bitflips_corrected;
 }
 
-static int mxc_nand_correct_data_v2_v3(struct mtd_info *mtd, u_char *dat,
-				 u_char *read_ecc, u_char *calc_ecc)
+static int mxc_nand_read_page_v2_v3(struct nand_chip *chip, void *buf,
+				    void *oob, bool ecc, int page)
 {
-	struct nand_chip *nand_chip = mtd_to_nand(mtd);
-	struct mxc_nand_host *host = nand_get_controller_data(nand_chip);
+	struct mtd_info *mtd = nand_to_mtd(chip);
+	struct mxc_nand_host *host = nand_get_controller_data(chip);
+	unsigned int max_bitflips = 0;
 	u32 ecc_stat, err;
-	int no_subpages = 1;
-	int ret = 0;
+	int no_subpages;
 	u8 ecc_bit_mask, err_limit;
 
+	host->devtype_data->enable_hwecc(chip, ecc);
+
+	host->devtype_data->send_cmd(host, NAND_CMD_READ0, false);
+	mxc_do_addr_cycle(mtd, 0, page);
+
+	if (mtd->writesize > 512)
+		host->devtype_data->send_cmd(host,
+				NAND_CMD_READSTART, true);
+
+	host->devtype_data->send_page(mtd, NFC_OUTPUT);
+
+	if (buf)
+		memcpy32_fromio(buf, host->main_area0, mtd->writesize);
+	if (oob)
+		copy_spare(mtd, true, oob);
+
 	ecc_bit_mask = (host->eccsize == 4) ? 0x7 : 0xf;
 	err_limit = (host->eccsize == 4) ? 0x4 : 0x8;
 
@@ -634,25 +819,99 @@ static int mxc_nand_correct_data_v2_v3(struct mtd_info *mtd, u_char *dat,
 	do {
 		err = ecc_stat & ecc_bit_mask;
 		if (err > err_limit) {
-			dev_dbg(host->dev, "UnCorrectable RS-ECC Error\n");
-			return -EBADMSG;
+			mtd->ecc_stats.failed++;
 		} else {
-			ret += err;
+			mtd->ecc_stats.corrected += err;
+			max_bitflips = max_t(unsigned int, max_bitflips, err);
 		}
+
 		ecc_stat >>= 4;
 	} while (--no_subpages);
 
-	dev_dbg(host->dev, "%d Symbol Correctable RS-ECC Error\n", ret);
+	return max_bitflips;
+}
 
-	return ret;
+static int mxc_nand_read_page(struct mtd_info *mtd, struct nand_chip *chip,
+			      uint8_t *buf, int oob_required, int page)
+{
+	struct mxc_nand_host *host = nand_get_controller_data(chip);
+	void *oob_buf;
+
+	if (oob_required)
+		oob_buf = chip->oob_poi;
+	else
+		oob_buf = NULL;
+
+	return host->devtype_data->read_page(chip, buf, oob_buf, 1, page);
+}
+
+static int mxc_nand_read_page_raw(struct mtd_info *mtd, struct nand_chip *chip,
+				  uint8_t *buf, int oob_required, int page)
+{
+	struct mxc_nand_host *host = nand_get_controller_data(chip);
+	void *oob_buf;
+
+	if (oob_required)
+		oob_buf = chip->oob_poi;
+	else
+		oob_buf = NULL;
+
+	return host->devtype_data->read_page(chip, buf, oob_buf, 0, page);
+}
+
+static int mxc_nand_read_oob(struct mtd_info *mtd, struct nand_chip *chip,
+			     int page)
+{
+	struct mxc_nand_host *host = nand_get_controller_data(chip);
+
+	return host->devtype_data->read_page(chip, NULL, chip->oob_poi, 0,
+					     page);
 }
 
-static int mxc_nand_calculate_ecc(struct mtd_info *mtd, const u_char *dat,
-				  u_char *ecc_code)
+static int mxc_nand_write_page(struct nand_chip *chip, const uint8_t *buf,
+			       bool ecc, int page)
 {
+	struct mtd_info *mtd = nand_to_mtd(chip);
+	struct mxc_nand_host *host = nand_get_controller_data(chip);
+
+	host->devtype_data->enable_hwecc(chip, ecc);
+
+	host->devtype_data->send_cmd(host, NAND_CMD_SEQIN, false);
+	mxc_do_addr_cycle(mtd, 0, page);
+
+	memcpy32_toio(host->main_area0, buf, mtd->writesize);
+	copy_spare(mtd, false, chip->oob_poi);
+
+	host->devtype_data->send_page(mtd, NFC_INPUT);
+	host->devtype_data->send_cmd(host, NAND_CMD_PAGEPROG, true);
+	mxc_do_addr_cycle(mtd, 0, page);
+
 	return 0;
 }
 
+static int mxc_nand_write_page_ecc(struct mtd_info *mtd, struct nand_chip *chip,
+				   const uint8_t *buf, int oob_required,
+				   int page)
+{
+	return mxc_nand_write_page(chip, buf, true, page);
+}
+
+static int mxc_nand_write_page_raw(struct mtd_info *mtd, struct nand_chip *chip,
+				   const uint8_t *buf, int oob_required, int page)
+{
+	return mxc_nand_write_page(chip, buf, false, page);
+}
+
+static int mxc_nand_write_oob(struct mtd_info *mtd, struct nand_chip *chip,
+			      int page)
+{
+	struct mxc_nand_host *host = nand_get_controller_data(chip);
+
+	memset(host->data_buf, 0xff, mtd->writesize);
+
+	return mxc_nand_write_page(chip, host->data_buf, false, page);
+}
+
 static u_char mxc_nand_read_byte(struct mtd_info *mtd)
 {
 	struct nand_chip *nand_chip = mtd_to_nand(mtd);
@@ -772,109 +1031,6 @@ static void mxc_nand_select_chip_v2(struct mtd_info *mtd, int chip)
 	writew(host->active_cs << 4, NFC_V1_V2_BUF_ADDR);
 }
 
-/*
- * The controller splits a page into data chunks of 512 bytes + partial oob.
- * There are writesize / 512 such chunks, the size of the partial oob parts is
- * oobsize / #chunks rounded down to a multiple of 2. The last oob chunk then
- * contains additionally the byte lost by rounding (if any).
- * This function handles the needed shuffling between host->data_buf (which
- * holds a page in natural order, i.e. writesize bytes data + oobsize bytes
- * spare) and the NFC buffer.
- */
-static void copy_spare(struct mtd_info *mtd, bool bfrom)
-{
-	struct nand_chip *this = mtd_to_nand(mtd);
-	struct mxc_nand_host *host = nand_get_controller_data(this);
-	u16 i, oob_chunk_size;
-	u16 num_chunks = mtd->writesize / 512;
-
-	u8 *d = host->data_buf + mtd->writesize;
-	u8 __iomem *s = host->spare0;
-	u16 sparebuf_size = host->devtype_data->spare_len;
-
-	/* size of oob chunk for all but possibly the last one */
-	oob_chunk_size = (host->used_oobsize / num_chunks) & ~1;
-
-	if (bfrom) {
-		for (i = 0; i < num_chunks - 1; i++)
-			memcpy16_fromio(d + i * oob_chunk_size,
-					s + i * sparebuf_size,
-					oob_chunk_size);
-
-		/* the last chunk */
-		memcpy16_fromio(d + i * oob_chunk_size,
-				s + i * sparebuf_size,
-				host->used_oobsize - i * oob_chunk_size);
-	} else {
-		for (i = 0; i < num_chunks - 1; i++)
-			memcpy16_toio(&s[i * sparebuf_size],
-				      &d[i * oob_chunk_size],
-				      oob_chunk_size);
-
-		/* the last chunk */
-		memcpy16_toio(&s[i * sparebuf_size],
-			      &d[i * oob_chunk_size],
-			      host->used_oobsize - i * oob_chunk_size);
-	}
-}
-
-/*
- * MXC NANDFC can only perform full page+spare or spare-only read/write.  When
- * the upper layers perform a read/write buf operation, the saved column address
- * is used to index into the full page. So usually this function is called with
- * column == 0 (unless no column cycle is needed indicated by column == -1)
- */
-static void mxc_do_addr_cycle(struct mtd_info *mtd, int column, int page_addr)
-{
-	struct nand_chip *nand_chip = mtd_to_nand(mtd);
-	struct mxc_nand_host *host = nand_get_controller_data(nand_chip);
-
-	/* Write out column address, if necessary */
-	if (column != -1) {
-		host->devtype_data->send_addr(host, column & 0xff,
-					      page_addr == -1);
-		if (mtd->writesize > 512)
-			/* another col addr cycle for 2k page */
-			host->devtype_data->send_addr(host,
-						      (column >> 8) & 0xff,
-						      false);
-	}
-
-	/* Write out page address, if necessary */
-	if (page_addr != -1) {
-		/* paddr_0 - p_addr_7 */
-		host->devtype_data->send_addr(host, (page_addr & 0xff), false);
-
-		if (mtd->writesize > 512) {
-			if (mtd->size >= 0x10000000) {
-				/* paddr_8 - paddr_15 */
-				host->devtype_data->send_addr(host,
-						(page_addr >> 8) & 0xff,
-						false);
-				host->devtype_data->send_addr(host,
-						(page_addr >> 16) & 0xff,
-						true);
-			} else
-				/* paddr_8 - paddr_15 */
-				host->devtype_data->send_addr(host,
-						(page_addr >> 8) & 0xff, true);
-		} else {
-			if (nand_chip->options & NAND_ROW_ADDR_3) {
-				/* paddr_8 - paddr_15 */
-				host->devtype_data->send_addr(host,
-						(page_addr >> 8) & 0xff,
-						false);
-				host->devtype_data->send_addr(host,
-						(page_addr >> 16) & 0xff,
-						true);
-			} else
-				/* paddr_8 - paddr_15 */
-				host->devtype_data->send_addr(host,
-						(page_addr >> 8) & 0xff, true);
-		}
-	}
-}
-
 #define MXC_V1_ECCBYTES		5
 
 static int mxc_v1_ooblayout_ecc(struct mtd_info *mtd, int section,
@@ -1235,57 +1391,6 @@ static void mxc_nand_command(struct mtd_info *mtd, unsigned command,
 		mxc_do_addr_cycle(mtd, column, page_addr);
 		break;
 
-	case NAND_CMD_READ0:
-	case NAND_CMD_READOOB:
-		if (command == NAND_CMD_READ0)
-			host->buf_start = column;
-		else
-			host->buf_start = column + mtd->writesize;
-
-		command = NAND_CMD_READ0; /* only READ0 is valid */
-
-		host->devtype_data->send_cmd(host, command, false);
-		WARN_ONCE(column < 0,
-			  "Unexpected column/row value (cmd=%u, col=%d, row=%d)\n",
-			  command, column, page_addr);
-		mxc_do_addr_cycle(mtd, 0, page_addr);
-
-		if (mtd->writesize > 512)
-			host->devtype_data->send_cmd(host,
-					NAND_CMD_READSTART, true);
-
-		host->devtype_data->send_page(mtd, NFC_OUTPUT);
-
-		memcpy32_fromio(host->data_buf, host->main_area0,
-				mtd->writesize);
-		copy_spare(mtd, true);
-		break;
-
-	case NAND_CMD_SEQIN:
-		if (column >= mtd->writesize)
-			/* call ourself to read a page */
-			mxc_nand_command(mtd, NAND_CMD_READ0, 0, page_addr);
-
-		host->buf_start = column;
-
-		host->devtype_data->send_cmd(host, command, false);
-		WARN_ONCE(column < -1,
-			  "Unexpected column/row value (cmd=%u, col=%d, row=%d)\n",
-			  command, column, page_addr);
-		mxc_do_addr_cycle(mtd, 0, page_addr);
-		break;
-
-	case NAND_CMD_PAGEPROG:
-		memcpy32_toio(host->main_area0, host->data_buf, mtd->writesize);
-		copy_spare(mtd, false);
-		host->devtype_data->send_page(mtd, NFC_INPUT);
-		host->devtype_data->send_cmd(host, command, true);
-		WARN_ONCE(column != -1 || page_addr != -1,
-			  "Unexpected column/row value (cmd=%u, col=%d, row=%d)\n",
-			  command, column, page_addr);
-		mxc_do_addr_cycle(mtd, column, page_addr);
-		break;
-
 	case NAND_CMD_READID:
 		host->devtype_data->send_cmd(host, command, true);
 		mxc_do_addr_cycle(mtd, column, page_addr);
@@ -1316,19 +1421,13 @@ static void mxc_nand_command(struct mtd_info *mtd, unsigned command,
 	}
 }
 
-static int mxc_nand_onfi_set_features(struct mtd_info *mtd,
-				      struct nand_chip *chip, int addr,
-				      u8 *subfeature_param)
+static int mxc_nand_set_features(struct mtd_info *mtd, struct nand_chip *chip,
+				 int addr, u8 *subfeature_param)
 {
 	struct nand_chip *nand_chip = mtd_to_nand(mtd);
 	struct mxc_nand_host *host = nand_get_controller_data(nand_chip);
 	int i;
 
-	if (!chip->onfi_version ||
-	    !(le16_to_cpu(chip->onfi_params.opt_cmd)
-	      & ONFI_OPT_CMD_SET_GET_FEATURES))
-		return -EINVAL;
-
 	host->buf_start = 0;
 
 	for (i = 0; i < ONFI_SUBFEATURE_PARAM_LEN; ++i)
@@ -1342,19 +1441,13 @@ static int mxc_nand_onfi_set_features(struct mtd_info *mtd,
 	return 0;
 }
 
-static int mxc_nand_onfi_get_features(struct mtd_info *mtd,
-				      struct nand_chip *chip, int addr,
-				      u8 *subfeature_param)
+static int mxc_nand_get_features(struct mtd_info *mtd, struct nand_chip *chip,
+				 int addr, u8 *subfeature_param)
 {
 	struct nand_chip *nand_chip = mtd_to_nand(mtd);
 	struct mxc_nand_host *host = nand_get_controller_data(nand_chip);
 	int i;
 
-	if (!chip->onfi_version ||
-	    !(le16_to_cpu(chip->onfi_params.opt_cmd)
-	      & ONFI_OPT_CMD_SET_GET_FEATURES))
-		return -EINVAL;
-
 	host->devtype_data->send_cmd(host, NAND_CMD_GET_FEATURES, false);
 	mxc_do_addr_cycle(mtd, addr, -1);
 	host->devtype_data->send_page(mtd, NFC_OUTPUT);
@@ -1397,6 +1490,7 @@ static struct nand_bbt_descr bbt_mirror_descr = {
 /* v1 + irqpending_quirk: i.MX21 */
 static const struct mxc_nand_devtype_data imx21_nand_devtype_data = {
 	.preset = preset_v1,
+	.read_page = mxc_nand_read_page_v1,
 	.send_cmd = send_cmd_v1_v2,
 	.send_addr = send_addr_v1_v2,
 	.send_page = send_page_v1,
@@ -1407,7 +1501,7 @@ static const struct mxc_nand_devtype_data imx21_nand_devtype_data = {
 	.get_ecc_status = get_ecc_status_v1,
 	.ooblayout = &mxc_v1_ooblayout_ops,
 	.select_chip = mxc_nand_select_chip_v1_v3,
-	.correct_data = mxc_nand_correct_data_v1,
+	.enable_hwecc = mxc_nand_enable_hwecc_v1_v2,
 	.irqpending_quirk = 1,
 	.needs_ip = 0,
 	.regs_offset = 0xe00,
@@ -1420,6 +1514,7 @@ static const struct mxc_nand_devtype_data imx21_nand_devtype_data = {
 /* v1 + !irqpending_quirk: i.MX27, i.MX31 */
 static const struct mxc_nand_devtype_data imx27_nand_devtype_data = {
 	.preset = preset_v1,
+	.read_page = mxc_nand_read_page_v1,
 	.send_cmd = send_cmd_v1_v2,
 	.send_addr = send_addr_v1_v2,
 	.send_page = send_page_v1,
@@ -1430,7 +1525,7 @@ static const struct mxc_nand_devtype_data imx27_nand_devtype_data = {
 	.get_ecc_status = get_ecc_status_v1,
 	.ooblayout = &mxc_v1_ooblayout_ops,
 	.select_chip = mxc_nand_select_chip_v1_v3,
-	.correct_data = mxc_nand_correct_data_v1,
+	.enable_hwecc = mxc_nand_enable_hwecc_v1_v2,
 	.irqpending_quirk = 0,
 	.needs_ip = 0,
 	.regs_offset = 0xe00,
@@ -1444,6 +1539,7 @@ static const struct mxc_nand_devtype_data imx27_nand_devtype_data = {
 /* v21: i.MX25, i.MX35 */
 static const struct mxc_nand_devtype_data imx25_nand_devtype_data = {
 	.preset = preset_v2,
+	.read_page = mxc_nand_read_page_v2_v3,
 	.send_cmd = send_cmd_v1_v2,
 	.send_addr = send_addr_v1_v2,
 	.send_page = send_page_v2,
@@ -1454,8 +1550,8 @@ static const struct mxc_nand_devtype_data imx25_nand_devtype_data = {
 	.get_ecc_status = get_ecc_status_v2,
 	.ooblayout = &mxc_v2_ooblayout_ops,
 	.select_chip = mxc_nand_select_chip_v2,
-	.correct_data = mxc_nand_correct_data_v2_v3,
 	.setup_data_interface = mxc_nand_v2_setup_data_interface,
+	.enable_hwecc = mxc_nand_enable_hwecc_v1_v2,
 	.irqpending_quirk = 0,
 	.needs_ip = 0,
 	.regs_offset = 0x1e00,
@@ -1469,6 +1565,7 @@ static const struct mxc_nand_devtype_data imx25_nand_devtype_data = {
 /* v3.2a: i.MX51 */
 static const struct mxc_nand_devtype_data imx51_nand_devtype_data = {
 	.preset = preset_v3,
+	.read_page = mxc_nand_read_page_v2_v3,
 	.send_cmd = send_cmd_v3,
 	.send_addr = send_addr_v3,
 	.send_page = send_page_v3,
@@ -1479,7 +1576,7 @@ static const struct mxc_nand_devtype_data imx51_nand_devtype_data = {
 	.get_ecc_status = get_ecc_status_v3,
 	.ooblayout = &mxc_v2_ooblayout_ops,
 	.select_chip = mxc_nand_select_chip_v1_v3,
-	.correct_data = mxc_nand_correct_data_v2_v3,
+	.enable_hwecc = mxc_nand_enable_hwecc_v3,
 	.irqpending_quirk = 0,
 	.needs_ip = 1,
 	.regs_offset = 0,
@@ -1494,6 +1591,7 @@ static const struct mxc_nand_devtype_data imx51_nand_devtype_data = {
 /* v3.2b: i.MX53 */
 static const struct mxc_nand_devtype_data imx53_nand_devtype_data = {
 	.preset = preset_v3,
+	.read_page = mxc_nand_read_page_v2_v3,
 	.send_cmd = send_cmd_v3,
 	.send_addr = send_addr_v3,
 	.send_page = send_page_v3,
@@ -1504,7 +1602,7 @@ static const struct mxc_nand_devtype_data imx53_nand_devtype_data = {
 	.get_ecc_status = get_ecc_status_v3,
 	.ooblayout = &mxc_v2_ooblayout_ops,
 	.select_chip = mxc_nand_select_chip_v1_v3,
-	.correct_data = mxc_nand_correct_data_v2_v3,
+	.enable_hwecc = mxc_nand_enable_hwecc_v3,
 	.irqpending_quirk = 0,
 	.needs_ip = 1,
 	.regs_offset = 0,
@@ -1642,8 +1740,8 @@ static int mxcnd_probe(struct platform_device *pdev)
 	this->read_word = mxc_nand_read_word;
 	this->write_buf = mxc_nand_write_buf;
 	this->read_buf = mxc_nand_read_buf;
-	this->onfi_set_features = mxc_nand_onfi_set_features;
-	this->onfi_get_features = mxc_nand_onfi_get_features;
+	this->set_features = mxc_nand_set_features;
+	this->get_features = mxc_nand_get_features;
 
 	host->clk = devm_clk_get(&pdev->dev, NULL);
 	if (IS_ERR(host->clk))
@@ -1751,9 +1849,12 @@ static int mxcnd_probe(struct platform_device *pdev)
 
 	switch (this->ecc.mode) {
 	case NAND_ECC_HW:
-		this->ecc.calculate = mxc_nand_calculate_ecc;
-		this->ecc.hwctl = mxc_nand_enable_hwecc;
-		this->ecc.correct = host->devtype_data->correct_data;
+		this->ecc.read_page = mxc_nand_read_page;
+		this->ecc.read_page_raw = mxc_nand_read_page_raw;
+		this->ecc.read_oob = mxc_nand_read_oob;
+		this->ecc.write_page = mxc_nand_write_page_ecc;
+		this->ecc.write_page_raw = mxc_nand_write_page_raw;
+		this->ecc.write_oob = mxc_nand_write_oob;
 		break;
 
 	case NAND_ECC_SOFT:
@@ -1810,15 +1911,18 @@ static int mxcnd_probe(struct platform_device *pdev)
 		goto escan;
 
 	/* Register the partitions */
-	mtd_device_parse_register(mtd, part_probes,
-			NULL,
-			host->pdata.parts,
-			host->pdata.nr_parts);
+	err = mtd_device_parse_register(mtd, part_probes, NULL,
+					host->pdata.parts,
+					host->pdata.nr_parts);
+	if (err)
+		goto cleanup_nand;
 
 	platform_set_drvdata(pdev, host);
 
 	return 0;
 
+cleanup_nand:
+	nand_cleanup(this);
 escan:
 	if (host->clk_act)
 		clk_disable_unprepare(host->clk);
diff --git a/drivers/mtd/nand/nand_amd.c b/drivers/mtd/nand/raw/nand_amd.c
index 22f060f38123..22f060f38123 100644
--- a/drivers/mtd/nand/nand_amd.c
+++ b/drivers/mtd/nand/raw/nand_amd.c
diff --git a/drivers/mtd/nand/nand_base.c b/drivers/mtd/nand/raw/nand_base.c
index e70ca16a5118..72f3a89da513 100644
--- a/drivers/mtd/nand/nand_base.c
+++ b/drivers/mtd/nand/raw/nand_base.c
@@ -349,7 +349,7 @@ static void nand_write_byte16(struct mtd_info *mtd, uint8_t byte)
 	 *    8-bits of the data bus. During address transfers, the host shall
 	 *    set the upper 8-bits of the data bus to 00h.
 	 *
-	 * One user of the write_byte callback is nand_onfi_set_features. The
+	 * One user of the write_byte callback is nand_set_features. The
 	 * four parameters are specified to be written to I/O[7:0], but this is
 	 * neither an address nor a command transfer. Let's assume a 0 on the
 	 * upper I/O lines is OK.
@@ -527,7 +527,6 @@ static int nand_block_markbad_lowlevel(struct mtd_info *mtd, loff_t ofs)
 
 		/* Attempt erase before marking OOB */
 		memset(&einfo, 0, sizeof(einfo));
-		einfo.mtd = mtd;
 		einfo.addr = ofs;
 		einfo.len = 1ULL << chip->phys_erase_shift;
 		nand_erase_nand(mtd, &einfo, 0);
@@ -1160,6 +1159,60 @@ static int nand_wait(struct mtd_info *mtd, struct nand_chip *chip)
 	return status;
 }
 
+static bool nand_supports_get_features(struct nand_chip *chip, int addr)
+{
+	return (chip->parameters.supports_set_get_features &&
+		test_bit(addr, chip->parameters.get_feature_list));
+}
+
+static bool nand_supports_set_features(struct nand_chip *chip, int addr)
+{
+	return (chip->parameters.supports_set_get_features &&
+		test_bit(addr, chip->parameters.set_feature_list));
+}
+
+/**
+ * nand_get_features - wrapper to perform a GET_FEATURE
+ * @chip: NAND chip info structure
+ * @addr: feature address
+ * @subfeature_param: the subfeature parameters, a four bytes array
+ *
+ * Returns 0 for success, a negative error otherwise. Returns -ENOTSUPP if the
+ * operation cannot be handled.
+ */
+int nand_get_features(struct nand_chip *chip, int addr,
+		      u8 *subfeature_param)
+{
+	struct mtd_info *mtd = nand_to_mtd(chip);
+
+	if (!nand_supports_get_features(chip, addr))
+		return -ENOTSUPP;
+
+	return chip->get_features(mtd, chip, addr, subfeature_param);
+}
+EXPORT_SYMBOL_GPL(nand_get_features);
+
+/**
+ * nand_set_features - wrapper to perform a SET_FEATURE
+ * @chip: NAND chip info structure
+ * @addr: feature address
+ * @subfeature_param: the subfeature parameters, a four bytes array
+ *
+ * Returns 0 for success, a negative error otherwise. Returns -ENOTSUPP if the
+ * operation cannot be handled.
+ */
+int nand_set_features(struct nand_chip *chip, int addr,
+		      u8 *subfeature_param)
+{
+	struct mtd_info *mtd = nand_to_mtd(chip);
+
+	if (!nand_supports_set_features(chip, addr))
+		return -ENOTSUPP;
+
+	return chip->set_features(mtd, chip, addr, subfeature_param);
+}
+EXPORT_SYMBOL_GPL(nand_set_features);
+
 /**
  * nand_reset_data_interface - Reset data interface and timings
  * @chip: The NAND chip
@@ -1215,31 +1268,59 @@ static int nand_reset_data_interface(struct nand_chip *chip, int chipnr)
 static int nand_setup_data_interface(struct nand_chip *chip, int chipnr)
 {
 	struct mtd_info *mtd = nand_to_mtd(chip);
+	u8 tmode_param[ONFI_SUBFEATURE_PARAM_LEN] = {
+		chip->onfi_timing_mode_default,
+	};
 	int ret;
 
 	if (!chip->setup_data_interface)
 		return 0;
 
-	/*
-	 * Ensure the timing mode has been changed on the chip side
-	 * before changing timings on the controller side.
-	 */
-	if (chip->onfi_version &&
-	    (le16_to_cpu(chip->onfi_params.opt_cmd) &
-	     ONFI_OPT_CMD_SET_GET_FEATURES)) {
-		u8 tmode_param[ONFI_SUBFEATURE_PARAM_LEN] = {
-			chip->onfi_timing_mode_default,
-		};
-
-		ret = chip->onfi_set_features(mtd, chip,
-				ONFI_FEATURE_ADDR_TIMING_MODE,
-				tmode_param);
+	/* Change the mode on the chip side (if supported by the NAND chip) */
+	if (nand_supports_set_features(chip, ONFI_FEATURE_ADDR_TIMING_MODE)) {
+		chip->select_chip(mtd, chipnr);
+		ret = nand_set_features(chip, ONFI_FEATURE_ADDR_TIMING_MODE,
+					tmode_param);
+		chip->select_chip(mtd, -1);
 		if (ret)
-			goto err;
+			return ret;
 	}
 
+	/* Change the mode on the controller side */
 	ret = chip->setup_data_interface(mtd, chipnr, &chip->data_interface);
-err:
+	if (ret)
+		return ret;
+
+	/* Check the mode has been accepted by the chip, if supported */
+	if (!nand_supports_get_features(chip, ONFI_FEATURE_ADDR_TIMING_MODE))
+		return 0;
+
+	memset(tmode_param, 0, ONFI_SUBFEATURE_PARAM_LEN);
+	chip->select_chip(mtd, chipnr);
+	ret = nand_get_features(chip, ONFI_FEATURE_ADDR_TIMING_MODE,
+				tmode_param);
+	chip->select_chip(mtd, -1);
+	if (ret)
+		goto err_reset_chip;
+
+	if (tmode_param[0] != chip->onfi_timing_mode_default) {
+		pr_warn("timing mode %d not acknowledged by the NAND chip\n",
+			chip->onfi_timing_mode_default);
+		goto err_reset_chip;
+	}
+
+	return 0;
+
+err_reset_chip:
+	/*
+	 * Fallback to mode 0 if the chip explicitly did not ack the chosen
+	 * timing mode.
+	 */
+	nand_reset_data_interface(chip, chipnr);
+	chip->select_chip(mtd, chipnr);
+	nand_reset_op(chip);
+	chip->select_chip(mtd, -1);
+
 	return ret;
 }
 
@@ -2739,10 +2820,18 @@ int nand_reset(struct nand_chip *chip, int chipnr)
 	if (ret)
 		return ret;
 
-	chip->select_chip(mtd, chipnr);
+	/*
+	 * A nand_reset_data_interface() put both the NAND chip and the NAND
+	 * controller in timings mode 0. If the default mode for this chip is
+	 * also 0, no need to proceed to the change again. Plus, at probe time,
+	 * nand_setup_data_interface() uses ->set/get_features() which would
+	 * fail anyway as the parameter page is not available yet.
+	 */
+	if (!chip->onfi_timing_mode_default)
+		return 0;
+
 	chip->data_interface = saved_data_intf;
 	ret = nand_setup_data_interface(chip, chipnr);
-	chip->select_chip(mtd, -1);
 	if (ret)
 		return ret;
 
@@ -4605,22 +4694,20 @@ int nand_erase_nand(struct mtd_info *mtd, struct erase_info *instr,
 	if (nand_check_wp(mtd)) {
 		pr_debug("%s: device is write protected!\n",
 				__func__);
-		instr->state = MTD_ERASE_FAILED;
+		ret = -EIO;
 		goto erase_exit;
 	}
 
 	/* Loop through the pages */
 	len = instr->len;
 
-	instr->state = MTD_ERASING;
-
 	while (len) {
 		/* Check if we have a bad block, we do not erase bad blocks! */
 		if (nand_block_checkbad(mtd, ((loff_t) page) <<
 					chip->page_shift, allowbbt)) {
 			pr_warn("%s: attempt to erase a bad block at page 0x%08x\n",
 				    __func__, page);
-			instr->state = MTD_ERASE_FAILED;
+			ret = -EIO;
 			goto erase_exit;
 		}
 
@@ -4638,7 +4725,7 @@ int nand_erase_nand(struct mtd_info *mtd, struct erase_info *instr,
 		if (status) {
 			pr_debug("%s: failed erase, page 0x%08x\n",
 					__func__, page);
-			instr->state = MTD_ERASE_FAILED;
+			ret = -EIO;
 			instr->fail_addr =
 				((loff_t)page << chip->page_shift);
 			goto erase_exit;
@@ -4655,20 +4742,14 @@ int nand_erase_nand(struct mtd_info *mtd, struct erase_info *instr,
 			chip->select_chip(mtd, chipnr);
 		}
 	}
-	instr->state = MTD_ERASE_DONE;
 
+	ret = 0;
 erase_exit:
 
-	ret = instr->state == MTD_ERASE_DONE ? 0 : -EIO;
-
 	/* Deselect and wake up anyone waiting on the device */
 	chip->select_chip(mtd, -1);
 	nand_release_device(mtd);
 
-	/* Do call back function */
-	if (!ret)
-		mtd_erase_callback(instr);
-
 	/* Return more or less happy */
 	return ret;
 }
@@ -4769,44 +4850,35 @@ static int nand_max_bad_blocks(struct mtd_info *mtd, loff_t ofs, size_t len)
 }
 
 /**
- * nand_onfi_set_features- [REPLACEABLE] set features for ONFI nand
+ * nand_default_set_features- [REPLACEABLE] set NAND chip features
  * @mtd: MTD device structure
  * @chip: nand chip info structure
  * @addr: feature address.
  * @subfeature_param: the subfeature parameters, a four bytes array.
  */
-static int nand_onfi_set_features(struct mtd_info *mtd, struct nand_chip *chip,
-			int addr, uint8_t *subfeature_param)
+static int nand_default_set_features(struct mtd_info *mtd,
+				     struct nand_chip *chip, int addr,
+				     uint8_t *subfeature_param)
 {
-	if (!chip->onfi_version ||
-	    !(le16_to_cpu(chip->onfi_params.opt_cmd)
-	      & ONFI_OPT_CMD_SET_GET_FEATURES))
-		return -EINVAL;
-
 	return nand_set_features_op(chip, addr, subfeature_param);
 }
 
 /**
- * nand_onfi_get_features- [REPLACEABLE] get features for ONFI nand
+ * nand_default_get_features- [REPLACEABLE] get NAND chip features
  * @mtd: MTD device structure
  * @chip: nand chip info structure
  * @addr: feature address.
  * @subfeature_param: the subfeature parameters, a four bytes array.
  */
-static int nand_onfi_get_features(struct mtd_info *mtd, struct nand_chip *chip,
-			int addr, uint8_t *subfeature_param)
+static int nand_default_get_features(struct mtd_info *mtd,
+				     struct nand_chip *chip, int addr,
+				     uint8_t *subfeature_param)
 {
-	if (!chip->onfi_version ||
-	    !(le16_to_cpu(chip->onfi_params.opt_cmd)
-	      & ONFI_OPT_CMD_SET_GET_FEATURES))
-		return -EINVAL;
-
 	return nand_get_features_op(chip, addr, subfeature_param);
 }
 
 /**
- * nand_onfi_get_set_features_notsupp - set/get features stub returning
- *					-ENOTSUPP
+ * nand_get_set_features_notsupp - set/get features stub returning -ENOTSUPP
  * @mtd: MTD device structure
  * @chip: nand chip info structure
  * @addr: feature address.
@@ -4815,13 +4887,12 @@ static int nand_onfi_get_features(struct mtd_info *mtd, struct nand_chip *chip,
  * Should be used by NAND controller drivers that do not support the SET/GET
  * FEATURES operations.
  */
-int nand_onfi_get_set_features_notsupp(struct mtd_info *mtd,
-				       struct nand_chip *chip, int addr,
-				       u8 *subfeature_param)
+int nand_get_set_features_notsupp(struct mtd_info *mtd, struct nand_chip *chip,
+				  int addr, u8 *subfeature_param)
 {
 	return -ENOTSUPP;
 }
-EXPORT_SYMBOL(nand_onfi_get_set_features_notsupp);
+EXPORT_SYMBOL(nand_get_set_features_notsupp);
 
 /**
  * nand_suspend - [MTD Interface] Suspend the NAND flash
@@ -4878,10 +4949,10 @@ static void nand_set_defaults(struct nand_chip *chip)
 		chip->select_chip = nand_select_chip;
 
 	/* set for ONFI nand */
-	if (!chip->onfi_set_features)
-		chip->onfi_set_features = nand_onfi_set_features;
-	if (!chip->onfi_get_features)
-		chip->onfi_get_features = nand_onfi_get_features;
+	if (!chip->set_features)
+		chip->set_features = nand_default_set_features;
+	if (!chip->get_features)
+		chip->get_features = nand_default_get_features;
 
 	/* If called twice, pointers that depend on busw may need to be reset */
 	if (!chip->read_byte || chip->read_byte == nand_read_byte)
@@ -5021,7 +5092,7 @@ ext_out:
 static int nand_flash_detect_onfi(struct nand_chip *chip)
 {
 	struct mtd_info *mtd = nand_to_mtd(chip);
-	struct nand_onfi_params *p = &chip->onfi_params;
+	struct nand_onfi_params *p;
 	char id[4];
 	int i, ret, val;
 
@@ -5030,14 +5101,23 @@ static int nand_flash_detect_onfi(struct nand_chip *chip)
 	if (ret || strncmp(id, "ONFI", 4))
 		return 0;
 
+	/* ONFI chip: allocate a buffer to hold its parameter page */
+	p = kzalloc(sizeof(*p), GFP_KERNEL);
+	if (!p)
+		return -ENOMEM;
+
 	ret = nand_read_param_page_op(chip, 0, NULL, 0);
-	if (ret)
-		return 0;
+	if (ret) {
+		ret = 0;
+		goto free_onfi_param_page;
+	}
 
 	for (i = 0; i < 3; i++) {
 		ret = nand_read_data_op(chip, p, sizeof(*p), true);
-		if (ret)
-			return 0;
+		if (ret) {
+			ret = 0;
+			goto free_onfi_param_page;
+		}
 
 		if (onfi_crc16(ONFI_CRC_BASE, (uint8_t *)p, 254) ==
 				le16_to_cpu(p->crc)) {
@@ -5047,31 +5127,33 @@ static int nand_flash_detect_onfi(struct nand_chip *chip)
 
 	if (i == 3) {
 		pr_err("Could not find valid ONFI parameter page; aborting\n");
-		return 0;
+		goto free_onfi_param_page;
 	}
 
 	/* Check version */
 	val = le16_to_cpu(p->revision);
 	if (val & (1 << 5))
-		chip->onfi_version = 23;
+		chip->parameters.onfi.version = 23;
 	else if (val & (1 << 4))
-		chip->onfi_version = 22;
+		chip->parameters.onfi.version = 22;
 	else if (val & (1 << 3))
-		chip->onfi_version = 21;
+		chip->parameters.onfi.version = 21;
 	else if (val & (1 << 2))
-		chip->onfi_version = 20;
+		chip->parameters.onfi.version = 20;
 	else if (val & (1 << 1))
-		chip->onfi_version = 10;
+		chip->parameters.onfi.version = 10;
 
-	if (!chip->onfi_version) {
+	if (!chip->parameters.onfi.version) {
 		pr_info("unsupported ONFI version: %d\n", val);
-		return 0;
+		goto free_onfi_param_page;
+	} else {
+		ret = 1;
 	}
 
 	sanitize_string(p->manufacturer, sizeof(p->manufacturer));
 	sanitize_string(p->model, sizeof(p->model));
-	if (!mtd->name)
-		mtd->name = p->model;
+	strncpy(chip->parameters.model, p->model,
+		sizeof(chip->parameters.model) - 1);
 
 	mtd->writesize = le32_to_cpu(p->byte_per_page);
 
@@ -5093,14 +5175,14 @@ static int nand_flash_detect_onfi(struct nand_chip *chip)
 	chip->max_bb_per_die = le16_to_cpu(p->bb_per_lun);
 	chip->blocks_per_die = le32_to_cpu(p->blocks_per_lun);
 
-	if (onfi_feature(chip) & ONFI_FEATURE_16_BIT_BUS)
+	if (le16_to_cpu(p->features) & ONFI_FEATURE_16_BIT_BUS)
 		chip->options |= NAND_BUSWIDTH_16;
 
 	if (p->ecc_bits != 0xff) {
 		chip->ecc_strength_ds = p->ecc_bits;
 		chip->ecc_step_ds = 512;
-	} else if (chip->onfi_version >= 21 &&
-		(onfi_feature(chip) & ONFI_FEATURE_EXT_PARAM_PAGE)) {
+	} else if (chip->parameters.onfi.version >= 21 &&
+		(le16_to_cpu(p->features) & ONFI_FEATURE_EXT_PARAM_PAGE)) {
 
 		/*
 		 * The nand_flash_detect_ext_param_page() uses the
@@ -5118,7 +5200,28 @@ static int nand_flash_detect_onfi(struct nand_chip *chip)
 		pr_warn("Could not retrieve ONFI ECC requirements\n");
 	}
 
-	return 1;
+	/* Save some parameters from the parameter page for future use */
+	if (le16_to_cpu(p->opt_cmd) & ONFI_OPT_CMD_SET_GET_FEATURES) {
+		chip->parameters.supports_set_get_features = true;
+		bitmap_set(chip->parameters.get_feature_list,
+			   ONFI_FEATURE_ADDR_TIMING_MODE, 1);
+		bitmap_set(chip->parameters.set_feature_list,
+			   ONFI_FEATURE_ADDR_TIMING_MODE, 1);
+	}
+	chip->parameters.onfi.tPROG = le16_to_cpu(p->t_prog);
+	chip->parameters.onfi.tBERS = le16_to_cpu(p->t_bers);
+	chip->parameters.onfi.tR = le16_to_cpu(p->t_r);
+	chip->parameters.onfi.tCCS = le16_to_cpu(p->t_ccs);
+	chip->parameters.onfi.async_timing_mode =
+		le16_to_cpu(p->async_timing_mode);
+	chip->parameters.onfi.vendor_revision =
+		le16_to_cpu(p->vendor_revision);
+	memcpy(chip->parameters.onfi.vendor, p->vendor,
+	       sizeof(p->vendor));
+
+free_onfi_param_page:
+	kfree(p);
+	return ret;
 }
 
 /*
@@ -5127,8 +5230,9 @@ static int nand_flash_detect_onfi(struct nand_chip *chip)
 static int nand_flash_detect_jedec(struct nand_chip *chip)
 {
 	struct mtd_info *mtd = nand_to_mtd(chip);
-	struct nand_jedec_params *p = &chip->jedec_params;
+	struct nand_jedec_params *p;
 	struct jedec_ecc_info *ecc;
+	int jedec_version = 0;
 	char id[5];
 	int i, val, ret;
 
@@ -5137,14 +5241,23 @@ static int nand_flash_detect_jedec(struct nand_chip *chip)
 	if (ret || strncmp(id, "JEDEC", sizeof(id)))
 		return 0;
 
+	/* JEDEC chip: allocate a buffer to hold its parameter page */
+	p = kzalloc(sizeof(*p), GFP_KERNEL);
+	if (!p)
+		return -ENOMEM;
+
 	ret = nand_read_param_page_op(chip, 0x40, NULL, 0);
-	if (ret)
-		return 0;
+	if (ret) {
+		ret = 0;
+		goto free_jedec_param_page;
+	}
 
 	for (i = 0; i < 3; i++) {
 		ret = nand_read_data_op(chip, p, sizeof(*p), true);
-		if (ret)
-			return 0;
+		if (ret) {
+			ret = 0;
+			goto free_jedec_param_page;
+		}
 
 		if (onfi_crc16(ONFI_CRC_BASE, (uint8_t *)p, 510) ==
 				le16_to_cpu(p->crc))
@@ -5153,25 +5266,25 @@ static int nand_flash_detect_jedec(struct nand_chip *chip)
 
 	if (i == 3) {
 		pr_err("Could not find valid JEDEC parameter page; aborting\n");
-		return 0;
+		goto free_jedec_param_page;
 	}
 
 	/* Check version */
 	val = le16_to_cpu(p->revision);
 	if (val & (1 << 2))
-		chip->jedec_version = 10;
+		jedec_version = 10;
 	else if (val & (1 << 1))
-		chip->jedec_version = 1; /* vendor specific version */
+		jedec_version = 1; /* vendor specific version */
 
-	if (!chip->jedec_version) {
+	if (!jedec_version) {
 		pr_info("unsupported JEDEC version: %d\n", val);
-		return 0;
+		goto free_jedec_param_page;
 	}
 
 	sanitize_string(p->manufacturer, sizeof(p->manufacturer));
 	sanitize_string(p->model, sizeof(p->model));
-	if (!mtd->name)
-		mtd->name = p->model;
+	strncpy(chip->parameters.model, p->model,
+		sizeof(chip->parameters.model) - 1);
 
 	mtd->writesize = le32_to_cpu(p->byte_per_page);
 
@@ -5186,7 +5299,7 @@ static int nand_flash_detect_jedec(struct nand_chip *chip)
 	chip->chipsize *= (uint64_t)mtd->erasesize * p->lun_count;
 	chip->bits_per_cell = p->bits_per_cell;
 
-	if (jedec_feature(chip) & JEDEC_FEATURE_16_BIT_BUS)
+	if (le16_to_cpu(p->features) & JEDEC_FEATURE_16_BIT_BUS)
 		chip->options |= NAND_BUSWIDTH_16;
 
 	/* ECC info */
@@ -5199,7 +5312,9 @@ static int nand_flash_detect_jedec(struct nand_chip *chip)
 		pr_warn("Invalid codeword size\n");
 	}
 
-	return 1;
+free_jedec_param_page:
+	kfree(p);
+	return ret;
 }
 
 /*
@@ -5358,8 +5473,8 @@ static bool find_full_id_nand(struct nand_chip *chip,
 		chip->onfi_timing_mode_default =
 					type->onfi_timing_mode_default;
 
-		if (!mtd->name)
-			mtd->name = type->name;
+		strncpy(chip->parameters.model, type->name,
+			sizeof(chip->parameters.model) - 1);
 
 		return true;
 	}
@@ -5498,22 +5613,28 @@ static int nand_detect(struct nand_chip *chip, struct nand_flash_dev *type)
 		}
 	}
 
-	chip->onfi_version = 0;
+	chip->parameters.onfi.version = 0;
 	if (!type->name || !type->pagesize) {
 		/* Check if the chip is ONFI compliant */
-		if (nand_flash_detect_onfi(chip))
+		ret = nand_flash_detect_onfi(chip);
+		if (ret < 0)
+			return ret;
+		else if (ret)
 			goto ident_done;
 
 		/* Check if the chip is JEDEC compliant */
-		if (nand_flash_detect_jedec(chip))
+		ret = nand_flash_detect_jedec(chip);
+		if (ret < 0)
+			return ret;
+		else if (ret)
 			goto ident_done;
 	}
 
 	if (!type->name)
 		return -ENODEV;
 
-	if (!mtd->name)
-		mtd->name = type->name;
+	strncpy(chip->parameters.model, type->name,
+		sizeof(chip->parameters.model) - 1);
 
 	chip->chipsize = (uint64_t)type->chipsize << 20;
 
@@ -5526,6 +5647,8 @@ static int nand_detect(struct nand_chip *chip, struct nand_flash_dev *type)
 	chip->options |= type->options;
 
 ident_done:
+	if (!mtd->name)
+		mtd->name = chip->parameters.model;
 
 	if (chip->options & NAND_BUSWIDTH_AUTO) {
 		WARN_ON(busw & NAND_BUSWIDTH_16);
@@ -5572,17 +5695,8 @@ ident_done:
 
 	pr_info("device found, Manufacturer ID: 0x%02x, Chip ID: 0x%02x\n",
 		maf_id, dev_id);
-
-	if (chip->onfi_version)
-		pr_info("%s %s\n", nand_manufacturer_name(manufacturer),
-			chip->onfi_params.model);
-	else if (chip->jedec_version)
-		pr_info("%s %s\n", nand_manufacturer_name(manufacturer),
-			chip->jedec_params.model);
-	else
-		pr_info("%s %s\n", nand_manufacturer_name(manufacturer),
-			type->name);
-
+	pr_info("%s %s\n", nand_manufacturer_name(manufacturer),
+		chip->parameters.model);
 	pr_info("%d MiB, %s, erase size: %d KiB, page size: %d, OOB size: %d\n",
 		(int)(chip->chipsize >> 20), nand_is_slc(chip) ? "SLC" : "MLC",
 		mtd->erasesize >> 10, mtd->writesize, mtd->oobsize);
@@ -6474,10 +6588,7 @@ int nand_scan_tail(struct mtd_info *mtd)
 
 	/* Enter fastest possible mode on all dies. */
 	for (i = 0; i < chip->numchips; i++) {
-		chip->select_chip(mtd, i);
 		ret = nand_setup_data_interface(chip, i);
-		chip->select_chip(mtd, -1);
-
 		if (ret)
 			goto err_nand_manuf_cleanup;
 	}
diff --git a/drivers/mtd/nand/nand_bbt.c b/drivers/mtd/nand/raw/nand_bbt.c
index 36092850be2c..d9f4ceff2568 100644
--- a/drivers/mtd/nand/nand_bbt.c
+++ b/drivers/mtd/nand/raw/nand_bbt.c
@@ -852,7 +852,6 @@ static int write_bbt(struct mtd_info *mtd, uint8_t *buf,
 		}
 
 		memset(&einfo, 0, sizeof(einfo));
-		einfo.mtd = mtd;
 		einfo.addr = to;
 		einfo.len = 1 << this->bbt_erase_shift;
 		res = nand_erase_nand(mtd, &einfo, 1);
diff --git a/drivers/mtd/nand/nand_bch.c b/drivers/mtd/nand/raw/nand_bch.c
index 505441c9373b..7f11b68f6db1 100644
--- a/drivers/mtd/nand/nand_bch.c
+++ b/drivers/mtd/nand/raw/nand_bch.c
@@ -95,7 +95,7 @@ int nand_bch_correct_data(struct mtd_info *mtd, unsigned char *buf,
 					errloc[i]);
 		}
 	} else if (count < 0) {
-		printk(KERN_ERR "ecc unrecoverable error\n");
+		pr_err("ecc unrecoverable error\n");
 		count = -EBADMSG;
 	}
 	return count;
@@ -134,7 +134,7 @@ struct nand_bch_control *nand_bch_init(struct mtd_info *mtd)
 	}
 
 	if (!eccsize || !eccbytes) {
-		printk(KERN_WARNING "ecc parameters not supplied\n");
+		pr_warn("ecc parameters not supplied\n");
 		goto fail;
 	}
 
@@ -151,8 +151,8 @@ struct nand_bch_control *nand_bch_init(struct mtd_info *mtd)
 
 	/* verify that eccbytes has the expected value */
 	if (nbc->bch->ecc_bytes != eccbytes) {
-		printk(KERN_WARNING "invalid eccbytes %u, should be %u\n",
-		       eccbytes, nbc->bch->ecc_bytes);
+		pr_warn("invalid eccbytes %u, should be %u\n",
+			eccbytes, nbc->bch->ecc_bytes);
 		goto fail;
 	}
 
@@ -166,7 +166,7 @@ struct nand_bch_control *nand_bch_init(struct mtd_info *mtd)
 
 	/* sanity checks */
 	if (8*(eccsize+eccbytes) >= (1 << m)) {
-		printk(KERN_WARNING "eccsize %u is too large\n", eccsize);
+		pr_warn("eccsize %u is too large\n", eccsize);
 		goto fail;
 	}
 
@@ -181,7 +181,7 @@ struct nand_bch_control *nand_bch_init(struct mtd_info *mtd)
 	nand->ecc.steps = eccsteps;
 	nand->ecc.total = eccsteps * eccbytes;
 	if (mtd_ooblayout_count_eccbytes(mtd) != (eccsteps*eccbytes)) {
-		printk(KERN_WARNING "invalid ecc layout\n");
+		pr_warn("invalid ecc layout\n");
 		goto fail;
 	}
 
diff --git a/drivers/mtd/nand/nand_ecc.c b/drivers/mtd/nand/raw/nand_ecc.c
index 7613a0388044..8e132edbc5ce 100644
--- a/drivers/mtd/nand/nand_ecc.c
+++ b/drivers/mtd/nand/raw/nand_ecc.c
@@ -2,8 +2,6 @@
  * This file contains an ECC algorithm that detects and corrects 1 bit
  * errors in a 256 byte block of data.
  *
- * drivers/mtd/nand/nand_ecc.c
- *
  * Copyright © 2008 Koninklijke Philips Electronics NV.
  *                  Author: Frans Meulenbroeks
  *
@@ -30,15 +28,6 @@
  *
  */
 
-/*
- * The STANDALONE macro is useful when running the code outside the kernel
- * e.g. when running the code in a testbed or a benchmark program.
- * When STANDALONE is used, the module related macros are commented out
- * as well as the linux include files.
- * Instead a private definition of mtd_info is given to satisfy the compiler
- * (the code does not use mtd_info, so the code does not care)
- */
-#ifndef STANDALONE
 #include <linux/types.h>
 #include <linux/kernel.h>
 #include <linux/module.h>
@@ -46,17 +35,6 @@
 #include <linux/mtd/rawnand.h>
 #include <linux/mtd/nand_ecc.h>
 #include <asm/byteorder.h>
-#else
-#include <stdint.h>
-struct mtd_info;
-#define EXPORT_SYMBOL(x)  /* x */
-
-#define MODULE_LICENSE(x)	/* x */
-#define MODULE_AUTHOR(x)	/* x */
-#define MODULE_DESCRIPTION(x)	/* x */
-
-#define pr_err printf
-#endif
 
 /*
  * invparity is a 256 byte table that contains the odd parity
diff --git a/drivers/mtd/nand/nand_hynix.c b/drivers/mtd/nand/raw/nand_hynix.c
index d542908a0ebb..d542908a0ebb 100644
--- a/drivers/mtd/nand/nand_hynix.c
+++ b/drivers/mtd/nand/raw/nand_hynix.c
diff --git a/drivers/mtd/nand/nand_ids.c b/drivers/mtd/nand/raw/nand_ids.c
index 5423c3bb388e..5423c3bb388e 100644
--- a/drivers/mtd/nand/nand_ids.c
+++ b/drivers/mtd/nand/raw/nand_ids.c
diff --git a/drivers/mtd/nand/nand_macronix.c b/drivers/mtd/nand/raw/nand_macronix.c
index d290ff2a6d2f..7ed1f87e742a 100644
--- a/drivers/mtd/nand/nand_macronix.c
+++ b/drivers/mtd/nand/raw/nand_macronix.c
@@ -22,6 +22,19 @@ static int macronix_nand_init(struct nand_chip *chip)
 	if (nand_is_slc(chip))
 		chip->bbt_options |= NAND_BBT_SCAN2NDPAGE;
 
+	/*
+	 * MX30LF2G18AC chip does not support using SET/GET_FEATURES to change
+	 * the timings unlike what is declared in the parameter page. Unflag
+	 * this feature to avoid unnecessary downturns.
+	 */
+	if (chip->parameters.supports_set_get_features &&
+	    !strcmp("MX30LF2G18AC", chip->parameters.model)) {
+		bitmap_clear(chip->parameters.get_feature_list,
+			     ONFI_FEATURE_ADDR_TIMING_MODE, 1);
+		bitmap_clear(chip->parameters.set_feature_list,
+			     ONFI_FEATURE_ADDR_TIMING_MODE, 1);
+	}
+
 	return 0;
 }
 
diff --git a/drivers/mtd/nand/nand_micron.c b/drivers/mtd/nand/raw/nand_micron.c
index 02e109ae73f1..0af45b134c0c 100644
--- a/drivers/mtd/nand/nand_micron.c
+++ b/drivers/mtd/nand/raw/nand_micron.c
@@ -48,8 +48,7 @@ static int micron_nand_setup_read_retry(struct mtd_info *mtd, int retry_mode)
 	struct nand_chip *chip = mtd_to_nand(mtd);
 	u8 feature[ONFI_SUBFEATURE_PARAM_LEN] = {retry_mode};
 
-	return chip->onfi_set_features(mtd, chip, ONFI_FEATURE_ADDR_READ_RETRY,
-				       feature);
+	return nand_set_features(chip, ONFI_FEATURE_ADDR_READ_RETRY, feature);
 }
 
 /*
@@ -57,17 +56,18 @@ static int micron_nand_setup_read_retry(struct mtd_info *mtd, int retry_mode)
  */
 static int micron_nand_onfi_init(struct nand_chip *chip)
 {
-	struct nand_onfi_params *p = &chip->onfi_params;
-	struct nand_onfi_vendor_micron *micron = (void *)p->vendor;
+	struct nand_parameters *p = &chip->parameters;
+	struct nand_onfi_vendor_micron *micron = (void *)p->onfi.vendor;
 
-	if (!chip->onfi_version)
-		return 0;
-
-	if (le16_to_cpu(p->vendor_revision) < 1)
-		return 0;
+	if (chip->parameters.onfi.version && p->onfi.vendor_revision) {
+		chip->read_retries = micron->read_retry_options;
+		chip->setup_read_retry = micron_nand_setup_read_retry;
+	}
 
-	chip->read_retries = micron->read_retry_options;
-	chip->setup_read_retry = micron_nand_setup_read_retry;
+	if (p->supports_set_get_features) {
+		set_bit(ONFI_FEATURE_ADDR_READ_RETRY, p->set_feature_list);
+		set_bit(ONFI_FEATURE_ADDR_READ_RETRY, p->get_feature_list);
+	}
 
 	return 0;
 }
@@ -108,8 +108,7 @@ static int micron_nand_on_die_ecc_setup(struct nand_chip *chip, bool enable)
 	if (enable)
 		feature[0] |= ONFI_FEATURE_ON_DIE_ECC_EN;
 
-	return chip->onfi_set_features(nand_to_mtd(chip), chip,
-				       ONFI_FEATURE_ON_DIE_ECC, feature);
+	return nand_set_features(chip, ONFI_FEATURE_ON_DIE_ECC, feature);
 }
 
 static int
@@ -209,7 +208,7 @@ static int micron_supports_on_die_ecc(struct nand_chip *chip)
 	u8 feature[ONFI_SUBFEATURE_PARAM_LEN] = { 0, };
 	int ret;
 
-	if (chip->onfi_version == 0)
+	if (!chip->parameters.onfi.version)
 		return MICRON_ON_DIE_UNSUPPORTED;
 
 	if (chip->bits_per_cell != 1)
@@ -219,8 +218,10 @@ static int micron_supports_on_die_ecc(struct nand_chip *chip)
 	if (ret)
 		return MICRON_ON_DIE_UNSUPPORTED;
 
-	chip->onfi_get_features(nand_to_mtd(chip), chip,
-				ONFI_FEATURE_ON_DIE_ECC, feature);
+	ret = nand_get_features(chip, ONFI_FEATURE_ON_DIE_ECC, feature);
+	if (ret < 0)
+		return ret;
+
 	if ((feature[0] & ONFI_FEATURE_ON_DIE_ECC_EN) == 0)
 		return MICRON_ON_DIE_UNSUPPORTED;
 
@@ -228,8 +229,10 @@ static int micron_supports_on_die_ecc(struct nand_chip *chip)
 	if (ret)
 		return MICRON_ON_DIE_UNSUPPORTED;
 
-	chip->onfi_get_features(nand_to_mtd(chip), chip,
-				ONFI_FEATURE_ON_DIE_ECC, feature);
+	ret = nand_get_features(chip, ONFI_FEATURE_ON_DIE_ECC, feature);
+	if (ret < 0)
+		return ret;
+
 	if (feature[0] & ONFI_FEATURE_ON_DIE_ECC_EN)
 		return MICRON_ON_DIE_MANDATORY;
 
@@ -237,7 +240,7 @@ static int micron_supports_on_die_ecc(struct nand_chip *chip)
 	 * Some Micron NANDs have an on-die ECC of 4/512, some other
 	 * 8/512. We only support the former.
 	 */
-	if (chip->onfi_params.ecc_bits != 4)
+	if (chip->ecc_strength_ds != 4)
 		return MICRON_ON_DIE_UNSUPPORTED;
 
 	return MICRON_ON_DIE_SUPPORTED;
diff --git a/drivers/mtd/nand/nand_samsung.c b/drivers/mtd/nand/raw/nand_samsung.c
index ef022f62f74c..ef022f62f74c 100644
--- a/drivers/mtd/nand/nand_samsung.c
+++ b/drivers/mtd/nand/raw/nand_samsung.c
diff --git a/drivers/mtd/nand/nand_timings.c b/drivers/mtd/nand/raw/nand_timings.c
index 9400d039ddbd..7c4e4a371bbc 100644
--- a/drivers/mtd/nand/nand_timings.c
+++ b/drivers/mtd/nand/raw/nand_timings.c
@@ -306,17 +306,17 @@ int onfi_fill_data_interface(struct nand_chip *chip,
 	 * tR, tPROG, tCCS, ...
 	 * These information are part of the ONFI parameter page.
 	 */
-	if (chip->onfi_version) {
-		struct nand_onfi_params *params = &chip->onfi_params;
+	if (chip->parameters.onfi.version) {
+		struct nand_parameters *params = &chip->parameters;
 		struct nand_sdr_timings *timings = &iface->timings.sdr;
 
 		/* microseconds -> picoseconds */
-		timings->tPROG_max = 1000000ULL * le16_to_cpu(params->t_prog);
-		timings->tBERS_max = 1000000ULL * le16_to_cpu(params->t_bers);
-		timings->tR_max = 1000000ULL * le16_to_cpu(params->t_r);
+		timings->tPROG_max = 1000000ULL * params->onfi.tPROG;
+		timings->tBERS_max = 1000000ULL * params->onfi.tBERS;
+		timings->tR_max = 1000000ULL * params->onfi.tR;
 
 		/* nanoseconds -> picoseconds */
-		timings->tCCS_min = 1000UL * le16_to_cpu(params->t_ccs);
+		timings->tCCS_min = 1000UL * params->onfi.tCCS;
 	}
 
 	return 0;
diff --git a/drivers/mtd/nand/nand_toshiba.c b/drivers/mtd/nand/raw/nand_toshiba.c
index 57df857074e6..ab43f027cd23 100644
--- a/drivers/mtd/nand/nand_toshiba.c
+++ b/drivers/mtd/nand/raw/nand_toshiba.c
@@ -35,6 +35,32 @@ static void toshiba_nand_decode_id(struct nand_chip *chip)
 	    (chip->id.data[5] & 0x7) == 0x6 /* 24nm */ &&
 	    !(chip->id.data[4] & 0x80) /* !BENAND */)
 		mtd->oobsize = 32 * mtd->writesize >> 9;
+
+	/*
+	 * Extract ECC requirements from 6th id byte.
+	 * For Toshiba SLC, ecc requrements are as follows:
+	 *  - 43nm: 1 bit ECC for each 512Byte is required.
+	 *  - 32nm: 4 bit ECC for each 512Byte is required.
+	 *  - 24nm: 8 bit ECC for each 512Byte is required.
+	 */
+	if (chip->id.len >= 6 && nand_is_slc(chip)) {
+		chip->ecc_step_ds = 512;
+		switch (chip->id.data[5] & 0x7) {
+		case 0x4:
+			chip->ecc_strength_ds = 1;
+			break;
+		case 0x5:
+			chip->ecc_strength_ds = 4;
+			break;
+		case 0x6:
+			chip->ecc_strength_ds = 8;
+			break;
+		default:
+			WARN(1, "Could not get ECC info");
+			chip->ecc_step_ds = 0;
+			break;
+		}
+	}
 }
 
 static int toshiba_nand_init(struct nand_chip *chip)
diff --git a/drivers/mtd/nand/nandsim.c b/drivers/mtd/nand/raw/nandsim.c
index 44322a363ba5..e027c6f9d327 100644
--- a/drivers/mtd/nand/nandsim.c
+++ b/drivers/mtd/nand/raw/nandsim.c
@@ -23,6 +23,8 @@
  * Foundation, Inc., 59 Temple Place, Suite 330, Boston, MA 02111-1307, USA
  */
 
+#define pr_fmt(fmt)  "[nandsim]" fmt
+
 #include <linux/init.h>
 #include <linux/types.h>
 #include <linux/module.h>
@@ -179,20 +181,17 @@ MODULE_PARM_DESC(bch,		 "Enable BCH ecc and set how many bits should "
 /* The largest possible page size */
 #define NS_LARGEST_PAGE_SIZE	4096
 
-/* The prefix for simulator output */
-#define NS_OUTPUT_PREFIX "[nandsim]"
-
 /* Simulator's output macros (logging, debugging, warning, error) */
 #define NS_LOG(args...) \
-	do { if (log) printk(KERN_DEBUG NS_OUTPUT_PREFIX " log: " args); } while(0)
+	do { if (log) pr_debug(" log: " args); } while(0)
 #define NS_DBG(args...) \
-	do { if (dbg) printk(KERN_DEBUG NS_OUTPUT_PREFIX " debug: " args); } while(0)
+	do { if (dbg) pr_debug(" debug: " args); } while(0)
 #define NS_WARN(args...) \
-	do { printk(KERN_WARNING NS_OUTPUT_PREFIX " warning: " args); } while(0)
+	do { pr_warn(" warning: " args); } while(0)
 #define NS_ERR(args...) \
-	do { printk(KERN_ERR NS_OUTPUT_PREFIX " error: " args); } while(0)
+	do { pr_err(" error: " args); } while(0)
 #define NS_INFO(args...) \
-	do { printk(KERN_INFO NS_OUTPUT_PREFIX " " args); } while(0)
+	do { pr_info(" " args); } while(0)
 
 /* Busy-wait delay macros (microseconds, milliseconds) */
 #define NS_UDELAY(us) \
diff --git a/drivers/mtd/nand/ndfc.c b/drivers/mtd/nand/raw/ndfc.c
index d8a806894937..d8a806894937 100644
--- a/drivers/mtd/nand/ndfc.c
+++ b/drivers/mtd/nand/raw/ndfc.c
diff --git a/drivers/mtd/nand/nuc900_nand.c b/drivers/mtd/nand/raw/nuc900_nand.c
index af5b32c9a791..af5b32c9a791 100644
--- a/drivers/mtd/nand/nuc900_nand.c
+++ b/drivers/mtd/nand/raw/nuc900_nand.c
diff --git a/drivers/mtd/nand/omap2.c b/drivers/mtd/nand/raw/omap2.c
index 8cdf7d3d8fa7..e50c64adc3c8 100644
--- a/drivers/mtd/nand/omap2.c
+++ b/drivers/mtd/nand/raw/omap2.c
@@ -2263,12 +2263,15 @@ scan_tail:
 
 	err = mtd_device_register(mtd, NULL, 0);
 	if (err)
-		goto return_error;
+		goto cleanup_nand;
 
 	platform_set_drvdata(pdev, mtd);
 
 	return 0;
 
+cleanup_nand:
+	nand_cleanup(nand_chip);
+
 return_error:
 	if (!IS_ERR_OR_NULL(info->dma))
 		dma_release_channel(info->dma);
diff --git a/drivers/mtd/nand/omap_elm.c b/drivers/mtd/nand/raw/omap_elm.c
index a3f32f939cc1..a3f32f939cc1 100644
--- a/drivers/mtd/nand/omap_elm.c
+++ b/drivers/mtd/nand/raw/omap_elm.c
diff --git a/drivers/mtd/nand/orion_nand.c b/drivers/mtd/nand/raw/orion_nand.c
index 5a5aa1f07d07..7825fd3ce66b 100644
--- a/drivers/mtd/nand/orion_nand.c
+++ b/drivers/mtd/nand/raw/orion_nand.c
@@ -1,6 +1,4 @@
 /*
- * drivers/mtd/nand/orion_nand.c
- *
  * NAND support for Marvell Orion SoC platforms
  *
  * Tzachi Perelstein <tzachi@marvell.com>
diff --git a/drivers/mtd/nand/oxnas_nand.c b/drivers/mtd/nand/raw/oxnas_nand.c
index d649d5944826..d649d5944826 100644
--- a/drivers/mtd/nand/oxnas_nand.c
+++ b/drivers/mtd/nand/raw/oxnas_nand.c
diff --git a/drivers/mtd/nand/pasemi_nand.c b/drivers/mtd/nand/raw/pasemi_nand.c
index a47a7e4bd25a..a47a7e4bd25a 100644
--- a/drivers/mtd/nand/pasemi_nand.c
+++ b/drivers/mtd/nand/raw/pasemi_nand.c
diff --git a/drivers/mtd/nand/plat_nand.c b/drivers/mtd/nand/raw/plat_nand.c
index 925a1323604d..925a1323604d 100644
--- a/drivers/mtd/nand/plat_nand.c
+++ b/drivers/mtd/nand/raw/plat_nand.c
diff --git a/drivers/mtd/nand/qcom_nandc.c b/drivers/mtd/nand/raw/qcom_nandc.c
index 563b759ffca6..b554fb6e609c 100644
--- a/drivers/mtd/nand/qcom_nandc.c
+++ b/drivers/mtd/nand/raw/qcom_nandc.c
@@ -2651,8 +2651,8 @@ static int qcom_nand_host_init(struct qcom_nand_controller *nandc,
 	chip->read_byte		= qcom_nandc_read_byte;
 	chip->read_buf		= qcom_nandc_read_buf;
 	chip->write_buf		= qcom_nandc_write_buf;
-	chip->onfi_set_features	= nand_onfi_get_set_features_notsupp;
-	chip->onfi_get_features	= nand_onfi_get_set_features_notsupp;
+	chip->set_features	= nand_get_set_features_notsupp;
+	chip->get_features	= nand_get_set_features_notsupp;
 
 	/*
 	 * the bad block marker is readable only when we read the last codeword
diff --git a/drivers/mtd/nand/r852.c b/drivers/mtd/nand/raw/r852.c
index 595635b9e9de..dcdeb0660e5e 100644
--- a/drivers/mtd/nand/r852.c
+++ b/drivers/mtd/nand/raw/r852.c
@@ -7,6 +7,9 @@
  * published by the Free Software Foundation.
  */
 
+#define DRV_NAME "r852"
+#define pr_fmt(fmt)  DRV_NAME ": " fmt
+
 #include <linux/kernel.h>
 #include <linux/module.h>
 #include <linux/jiffies.h>
@@ -932,7 +935,7 @@ static int  r852_probe(struct pci_dev *pci_dev, const struct pci_device_id *id)
 		&dev->card_detect_work, 0);
 
 
-	printk(KERN_NOTICE DRV_NAME ": driver loaded successfully\n");
+	pr_notice("driver loaded successfully\n");
 	return 0;
 
 error10:
diff --git a/drivers/mtd/nand/r852.h b/drivers/mtd/nand/raw/r852.h
index 8713c57f6207..1eed2fc2fa42 100644
--- a/drivers/mtd/nand/r852.h
+++ b/drivers/mtd/nand/raw/r852.h
@@ -144,17 +144,14 @@ struct r852_device {
 	uint8_t ctlreg;			/* cached contents of control reg */
 };
 
-#define DRV_NAME "r852"
-
-
 #define dbg(format, ...) \
 	if (debug) \
-		printk(KERN_DEBUG DRV_NAME ": " format "\n", ## __VA_ARGS__)
+		pr_debug(format "\n", ## __VA_ARGS__)
 
 #define dbg_verbose(format, ...) \
 	if (debug > 1) \
-		printk(KERN_DEBUG DRV_NAME ": " format "\n", ## __VA_ARGS__)
+		pr_debug(format "\n", ## __VA_ARGS__)
 
 
 #define message(format, ...) \
-	printk(KERN_INFO DRV_NAME ": " format "\n", ## __VA_ARGS__)
+	pr_info(format "\n", ## __VA_ARGS__)
diff --git a/drivers/mtd/nand/s3c2410.c b/drivers/mtd/nand/raw/s3c2410.c
index 4c383eeec6f6..1bc0458063d8 100644
--- a/drivers/mtd/nand/s3c2410.c
+++ b/drivers/mtd/nand/raw/s3c2410.c
@@ -1,5 +1,4 @@
-/* linux/drivers/mtd/nand/s3c2410.c
- *
+/*
  * Copyright © 2004-2008 Simtec Electronics
  *	http://armlinux.simtec.co.uk/
  *	Ben Dooks <ben@simtec.co.uk>
@@ -125,13 +124,11 @@ struct s3c2410_nand_info;
  * @chip: The NAND chip information.
  * @set: The platform information supplied for this set of NAND chips.
  * @info: Link back to the hardware information.
- * @scan_res: The result from calling nand_scan_ident().
 */
 struct s3c2410_nand_mtd {
 	struct nand_chip		chip;
 	struct s3c2410_nand_set		*set;
 	struct s3c2410_nand_info	*info;
-	int				scan_res;
 };
 
 enum s3c_cpu_type {
@@ -1164,17 +1161,19 @@ static int s3c24xx_nand_probe(struct platform_device *pdev)
 		mtd->dev.parent = &pdev->dev;
 		s3c2410_nand_init_chip(info, nmtd, sets);
 
-		nmtd->scan_res = nand_scan_ident(mtd,
-						 (sets) ? sets->nr_chips : 1,
-						 NULL);
+		err = nand_scan_ident(mtd, (sets) ? sets->nr_chips : 1, NULL);
+		if (err)
+			goto exit_error;
 
-		if (nmtd->scan_res == 0) {
-			err = s3c2410_nand_update_chip(info, nmtd);
-			if (err < 0)
-				goto exit_error;
-			nand_scan_tail(mtd);
-			s3c2410_nand_add_partition(info, nmtd, sets);
-		}
+		err = s3c2410_nand_update_chip(info, nmtd);
+		if (err < 0)
+			goto exit_error;
+
+		err = nand_scan_tail(mtd);
+		if (err)
+			goto exit_error;
+
+		s3c2410_nand_add_partition(info, nmtd, sets);
 
 		if (sets != NULL)
 			sets++;
diff --git a/drivers/mtd/nand/sh_flctl.c b/drivers/mtd/nand/raw/sh_flctl.c
index c4e7755448e6..c7abceffcc40 100644
--- a/drivers/mtd/nand/sh_flctl.c
+++ b/drivers/mtd/nand/raw/sh_flctl.c
@@ -877,7 +877,7 @@ static void flctl_cmdfunc(struct mtd_info *mtd, unsigned int command,
 			else if (!flctl->seqin_column)
 				execmd_write_page_sector(mtd);
 			else
-				printk(KERN_ERR "Invalid address !?\n");
+				pr_err("Invalid address !?\n");
 			break;
 		}
 		set_cmd_regs(mtd, command, (command << 8) | NAND_CMD_SEQIN);
@@ -1180,8 +1180,8 @@ static int flctl_probe(struct platform_device *pdev)
 	nand->read_buf = flctl_read_buf;
 	nand->select_chip = flctl_select_chip;
 	nand->cmdfunc = flctl_cmdfunc;
-	nand->onfi_set_features = nand_onfi_get_set_features_notsupp;
-	nand->onfi_get_features = nand_onfi_get_set_features_notsupp;
+	nand->set_features = nand_get_set_features_notsupp;
+	nand->get_features = nand_get_set_features_notsupp;
 
 	if (pdata->flcmncr_val & SEL_16BIT)
 		nand->options |= NAND_BUSWIDTH_16;
@@ -1214,9 +1214,13 @@ static int flctl_probe(struct platform_device *pdev)
 		goto err_chip;
 
 	ret = mtd_device_register(flctl_mtd, pdata->parts, pdata->nr_parts);
+	if (ret)
+		goto cleanup_nand;
 
 	return 0;
 
+cleanup_nand:
+	nand_cleanup(nand);
 err_chip:
 	flctl_release_dma(flctl);
 	pm_runtime_disable(&pdev->dev);
diff --git a/drivers/mtd/nand/sharpsl.c b/drivers/mtd/nand/raw/sharpsl.c
index f59c455d9f51..e93df02c825e 100644
--- a/drivers/mtd/nand/sharpsl.c
+++ b/drivers/mtd/nand/raw/sharpsl.c
@@ -1,6 +1,4 @@
 /*
- * drivers/mtd/nand/sharpsl.c
- *
  *  Copyright (C) 2004 Richard Purdie
  *  Copyright (C) 2008 Dmitry Baryshkov
  *
diff --git a/drivers/mtd/nand/sm_common.c b/drivers/mtd/nand/raw/sm_common.c
index c378705c6e2b..7f5044a79f01 100644
--- a/drivers/mtd/nand/sm_common.c
+++ b/drivers/mtd/nand/raw/sm_common.c
@@ -119,9 +119,8 @@ static int sm_block_markbad(struct mtd_info *mtd, loff_t ofs)
 
 	ret = mtd_write_oob(mtd, ofs, &ops);
 	if (ret < 0 || ops.oobretlen != SM_OOB_SIZE) {
-		printk(KERN_NOTICE
-			"sm_common: can't mark sector at %i as bad\n",
-								(int)ofs);
+		pr_notice("sm_common: can't mark sector at %i as bad\n",
+			  (int)ofs);
 		return -EIO;
 	}
 
diff --git a/drivers/mtd/nand/sm_common.h b/drivers/mtd/nand/raw/sm_common.h
index 1581671b05ae..1581671b05ae 100644
--- a/drivers/mtd/nand/sm_common.h
+++ b/drivers/mtd/nand/raw/sm_common.h
diff --git a/drivers/mtd/nand/socrates_nand.c b/drivers/mtd/nand/raw/socrates_nand.c
index 575997d0ef8a..9824a9923583 100644
--- a/drivers/mtd/nand/socrates_nand.c
+++ b/drivers/mtd/nand/raw/socrates_nand.c
@@ -1,6 +1,4 @@
 /*
- * drivers/mtd/nand/socrates_nand.c
- *
  *  Copyright © 2008 Ilya Yanok, Emcraft Systems
  *
  *
diff --git a/drivers/mtd/nand/sunxi_nand.c b/drivers/mtd/nand/raw/sunxi_nand.c
index f5a55c63935c..aad42812a353 100644
--- a/drivers/mtd/nand/sunxi_nand.c
+++ b/drivers/mtd/nand/raw/sunxi_nand.c
@@ -1475,92 +1475,18 @@ pio_fallback:
 	return sunxi_nfc_hw_ecc_write_page(mtd, chip, buf, oob_required, page);
 }
 
-static int sunxi_nfc_hw_syndrome_ecc_read_page(struct mtd_info *mtd,
-					       struct nand_chip *chip,
-					       uint8_t *buf, int oob_required,
-					       int page)
-{
-	struct nand_ecc_ctrl *ecc = &chip->ecc;
-	unsigned int max_bitflips = 0;
-	int ret, i, cur_off = 0;
-	bool raw_mode = false;
-
-	nand_read_page_op(chip, page, 0, NULL, 0);
-
-	sunxi_nfc_hw_ecc_enable(mtd);
-
-	for (i = 0; i < ecc->steps; i++) {
-		int data_off = i * (ecc->size + ecc->bytes + 4);
-		int oob_off = data_off + ecc->size;
-		u8 *data = buf + (i * ecc->size);
-		u8 *oob = chip->oob_poi + (i * (ecc->bytes + 4));
-
-		ret = sunxi_nfc_hw_ecc_read_chunk(mtd, data, data_off, oob,
-						  oob_off, &cur_off,
-						  &max_bitflips, !i,
-						  oob_required,
-						  page);
-		if (ret < 0)
-			return ret;
-		else if (ret)
-			raw_mode = true;
-	}
-
-	if (oob_required)
-		sunxi_nfc_hw_ecc_read_extra_oob(mtd, chip->oob_poi, &cur_off,
-						!raw_mode, page);
-
-	sunxi_nfc_hw_ecc_disable(mtd);
-
-	return max_bitflips;
-}
-
-static int sunxi_nfc_hw_syndrome_ecc_write_page(struct mtd_info *mtd,
-						struct nand_chip *chip,
-						const uint8_t *buf,
-						int oob_required, int page)
-{
-	struct nand_ecc_ctrl *ecc = &chip->ecc;
-	int ret, i, cur_off = 0;
-
-	nand_prog_page_begin_op(chip, page, 0, NULL, 0);
-
-	sunxi_nfc_hw_ecc_enable(mtd);
-
-	for (i = 0; i < ecc->steps; i++) {
-		int data_off = i * (ecc->size + ecc->bytes + 4);
-		int oob_off = data_off + ecc->size;
-		const u8 *data = buf + (i * ecc->size);
-		const u8 *oob = chip->oob_poi + (i * (ecc->bytes + 4));
-
-		ret = sunxi_nfc_hw_ecc_write_chunk(mtd, data, data_off,
-						   oob, oob_off, &cur_off,
-						   false, page);
-		if (ret)
-			return ret;
-	}
-
-	if (oob_required || (chip->options & NAND_NEED_SCRAMBLING))
-		sunxi_nfc_hw_ecc_write_extra_oob(mtd, chip->oob_poi,
-						 &cur_off, page);
-
-	sunxi_nfc_hw_ecc_disable(mtd);
-
-	return nand_prog_page_end_op(chip);
-}
-
-static int sunxi_nfc_hw_common_ecc_read_oob(struct mtd_info *mtd,
-					    struct nand_chip *chip,
-					    int page)
+static int sunxi_nfc_hw_ecc_read_oob(struct mtd_info *mtd,
+				     struct nand_chip *chip,
+				     int page)
 {
 	chip->pagebuf = -1;
 
 	return chip->ecc.read_page(mtd, chip, chip->data_buf, 1, page);
 }
 
-static int sunxi_nfc_hw_common_ecc_write_oob(struct mtd_info *mtd,
-					     struct nand_chip *chip,
-					     int page)
+static int sunxi_nfc_hw_ecc_write_oob(struct mtd_info *mtd,
+				      struct nand_chip *chip,
+				      int page)
 {
 	int ret;
 
@@ -1801,9 +1727,14 @@ static const struct mtd_ooblayout_ops sunxi_nand_ooblayout_ops = {
 	.free = sunxi_nand_ooblayout_free,
 };
 
-static int sunxi_nand_hw_common_ecc_ctrl_init(struct mtd_info *mtd,
-					      struct nand_ecc_ctrl *ecc,
-					      struct device_node *np)
+static void sunxi_nand_hw_ecc_ctrl_cleanup(struct nand_ecc_ctrl *ecc)
+{
+	kfree(ecc->priv);
+}
+
+static int sunxi_nand_hw_ecc_ctrl_init(struct mtd_info *mtd,
+				       struct nand_ecc_ctrl *ecc,
+				       struct device_node *np)
 {
 	static const u8 strengths[] = { 16, 24, 28, 32, 40, 48, 56, 60, 64 };
 	struct nand_chip *nand = mtd_to_nand(mtd);
@@ -1889,37 +1820,11 @@ static int sunxi_nand_hw_common_ecc_ctrl_init(struct mtd_info *mtd,
 		goto err;
 	}
 
-	ecc->read_oob = sunxi_nfc_hw_common_ecc_read_oob;
-	ecc->write_oob = sunxi_nfc_hw_common_ecc_write_oob;
+	ecc->read_oob = sunxi_nfc_hw_ecc_read_oob;
+	ecc->write_oob = sunxi_nfc_hw_ecc_write_oob;
 	mtd_set_ooblayout(mtd, &sunxi_nand_ooblayout_ops);
 	ecc->priv = data;
 
-	return 0;
-
-err:
-	kfree(data);
-
-	return ret;
-}
-
-static void sunxi_nand_hw_common_ecc_ctrl_cleanup(struct nand_ecc_ctrl *ecc)
-{
-	kfree(ecc->priv);
-}
-
-static int sunxi_nand_hw_ecc_ctrl_init(struct mtd_info *mtd,
-				       struct nand_ecc_ctrl *ecc,
-				       struct device_node *np)
-{
-	struct nand_chip *nand = mtd_to_nand(mtd);
-	struct sunxi_nand_chip *sunxi_nand = to_sunxi_nand(nand);
-	struct sunxi_nfc *nfc = to_sunxi_nfc(sunxi_nand->nand.controller);
-	int ret;
-
-	ret = sunxi_nand_hw_common_ecc_ctrl_init(mtd, ecc, np);
-	if (ret)
-		return ret;
-
 	if (nfc->dmac) {
 		ecc->read_page = sunxi_nfc_hw_ecc_read_page_dma;
 		ecc->read_subpage = sunxi_nfc_hw_ecc_read_subpage_dma;
@@ -1937,33 +1842,18 @@ static int sunxi_nand_hw_ecc_ctrl_init(struct mtd_info *mtd,
 	ecc->write_oob_raw = nand_write_oob_std;
 
 	return 0;
-}
-
-static int sunxi_nand_hw_syndrome_ecc_ctrl_init(struct mtd_info *mtd,
-						struct nand_ecc_ctrl *ecc,
-						struct device_node *np)
-{
-	int ret;
-
-	ret = sunxi_nand_hw_common_ecc_ctrl_init(mtd, ecc, np);
-	if (ret)
-		return ret;
 
-	ecc->prepad = 4;
-	ecc->read_page = sunxi_nfc_hw_syndrome_ecc_read_page;
-	ecc->write_page = sunxi_nfc_hw_syndrome_ecc_write_page;
-	ecc->read_oob_raw = nand_read_oob_syndrome;
-	ecc->write_oob_raw = nand_write_oob_syndrome;
+err:
+	kfree(data);
 
-	return 0;
+	return ret;
 }
 
 static void sunxi_nand_ecc_cleanup(struct nand_ecc_ctrl *ecc)
 {
 	switch (ecc->mode) {
 	case NAND_ECC_HW:
-	case NAND_ECC_HW_SYNDROME:
-		sunxi_nand_hw_common_ecc_ctrl_cleanup(ecc);
+		sunxi_nand_hw_ecc_ctrl_cleanup(ecc);
 		break;
 	case NAND_ECC_NONE:
 	default:
@@ -1991,11 +1881,6 @@ static int sunxi_nand_ecc_init(struct mtd_info *mtd, struct nand_ecc_ctrl *ecc,
 		if (ret)
 			return ret;
 		break;
-	case NAND_ECC_HW_SYNDROME:
-		ret = sunxi_nand_hw_syndrome_ecc_ctrl_init(mtd, ecc, np);
-		if (ret)
-			return ret;
-		break;
 	case NAND_ECC_NONE:
 	case NAND_ECC_SOFT:
 		break;
diff --git a/drivers/mtd/nand/tango_nand.c b/drivers/mtd/nand/raw/tango_nand.c
index c5bee00b7f5e..f54518ffb36a 100644
--- a/drivers/mtd/nand/tango_nand.c
+++ b/drivers/mtd/nand/raw/tango_nand.c
@@ -591,8 +591,10 @@ static int chip_init(struct device *dev, struct device_node *np)
 	tchip->bb_cfg = BB_CFG(mtd->writesize, BBM_SIZE);
 
 	err = mtd_device_register(mtd, NULL, 0);
-	if (err)
+	if (err) {
+		nand_cleanup(chip);
 		return err;
+	}
 
 	nfc->chips[cs] = tchip;
 
diff --git a/drivers/mtd/nand/tmio_nand.c b/drivers/mtd/nand/raw/tmio_nand.c
index dcaa924502de..dcaa924502de 100644
--- a/drivers/mtd/nand/tmio_nand.c
+++ b/drivers/mtd/nand/raw/tmio_nand.c
diff --git a/drivers/mtd/nand/txx9ndfmc.c b/drivers/mtd/nand/raw/txx9ndfmc.c
index b567d212fe7d..b567d212fe7d 100644
--- a/drivers/mtd/nand/txx9ndfmc.c
+++ b/drivers/mtd/nand/raw/txx9ndfmc.c
diff --git a/drivers/mtd/nand/vf610_nfc.c b/drivers/mtd/nand/raw/vf610_nfc.c
index f367144f3c6f..d5a22fc96878 100644
--- a/drivers/mtd/nand/vf610_nfc.c
+++ b/drivers/mtd/nand/raw/vf610_nfc.c
@@ -36,6 +36,7 @@
 #include <linux/of_device.h>
 #include <linux/platform_device.h>
 #include <linux/slab.h>
+#include <linux/swab.h>
 
 #define	DRV_NAME		"vf610_nfc"
 
@@ -59,20 +60,21 @@
 #define OOB_64				0x0040
 #define OOB_MAX				0x0100
 
-/*
- * NFC_CMD2[CODE] values. See section:
- *  - 31.4.7 Flash Command Code Description, Vybrid manual
- *  - 23.8.6 Flash Command Sequencer, MPC5125 manual
- *
- * Briefly these are bitmasks of controller cycles.
- */
-#define READ_PAGE_CMD_CODE		0x7EE0
-#define READ_ONFI_PARAM_CMD_CODE	0x4860
-#define PROGRAM_PAGE_CMD_CODE		0x7FC0
-#define ERASE_CMD_CODE			0x4EC0
-#define READ_ID_CMD_CODE		0x4804
-#define RESET_CMD_CODE			0x4040
-#define STATUS_READ_CMD_CODE		0x4068
+/* NFC_CMD2[CODE] controller cycle bit masks */
+#define COMMAND_CMD_BYTE1		BIT(14)
+#define COMMAND_CAR_BYTE1		BIT(13)
+#define COMMAND_CAR_BYTE2		BIT(12)
+#define COMMAND_RAR_BYTE1		BIT(11)
+#define COMMAND_RAR_BYTE2		BIT(10)
+#define COMMAND_RAR_BYTE3		BIT(9)
+#define COMMAND_NADDR_BYTES(x)		GENMASK(13, 13 - (x) + 1)
+#define COMMAND_WRITE_DATA		BIT(8)
+#define COMMAND_CMD_BYTE2		BIT(7)
+#define COMMAND_RB_HANDSHAKE		BIT(6)
+#define COMMAND_READ_DATA		BIT(5)
+#define COMMAND_CMD_BYTE3		BIT(4)
+#define COMMAND_READ_STATUS		BIT(3)
+#define COMMAND_READ_ID			BIT(2)
 
 /* NFC ECC mode define */
 #define ECC_BYPASS			0
@@ -97,10 +99,13 @@
 /* NFC_COL_ADDR Field */
 #define COL_ADDR_MASK				0x0000FFFF
 #define COL_ADDR_SHIFT				0
+#define COL_ADDR(pos, val)			(((val) & 0xFF) << (8 * (pos)))
 
 /* NFC_ROW_ADDR Field */
 #define ROW_ADDR_MASK				0x00FFFFFF
 #define ROW_ADDR_SHIFT				0
+#define ROW_ADDR(pos, val)			(((val) & 0xFF) << (8 * (pos)))
+
 #define ROW_ADDR_CHIP_SEL_RB_MASK		0xF0000000
 #define ROW_ADDR_CHIP_SEL_RB_SHIFT		28
 #define ROW_ADDR_CHIP_SEL_MASK			0x0F000000
@@ -142,13 +147,6 @@
 #define ECC_STATUS_MASK		0x80
 #define ECC_STATUS_ERR_COUNT	0x3F
 
-enum vf610_nfc_alt_buf {
-	ALT_BUF_DATA = 0,
-	ALT_BUF_ID = 1,
-	ALT_BUF_STAT = 2,
-	ALT_BUF_ONFI = 3,
-};
-
 enum vf610_nfc_variant {
 	NFC_VFC610 = 1,
 };
@@ -158,13 +156,15 @@ struct vf610_nfc {
 	struct device *dev;
 	void __iomem *regs;
 	struct completion cmd_done;
-	uint buf_offset;
-	int write_sz;
 	/* Status and ID are in alternate locations. */
-	enum vf610_nfc_alt_buf alt_buf;
 	enum vf610_nfc_variant variant;
 	struct clk *clk;
-	bool use_hw_ecc;
+	/*
+	 * Indicate that user data is accessed (full page/oob). This is
+	 * useful to indicate the driver whether to swap byte endianness.
+	 * See comments in vf610_nfc_rd_from_sram/vf610_nfc_wr_to_sram.
+	 */
+	bool data_access;
 	u32 ecc_mode;
 };
 
@@ -173,6 +173,11 @@ static inline struct vf610_nfc *mtd_to_nfc(struct mtd_info *mtd)
 	return container_of(mtd_to_nand(mtd), struct vf610_nfc, chip);
 }
 
+static inline struct vf610_nfc *chip_to_nfc(struct nand_chip *chip)
+{
+	return container_of(chip, struct vf610_nfc, chip);
+}
+
 static inline u32 vf610_nfc_read(struct vf610_nfc *nfc, uint reg)
 {
 	return readl(nfc->regs + reg);
@@ -200,18 +205,84 @@ static inline void vf610_nfc_set_field(struct vf610_nfc *nfc, u32 reg,
 			(vf610_nfc_read(nfc, reg) & (~mask)) | val << shift);
 }
 
-static inline void vf610_nfc_memcpy(void *dst, const void __iomem *src,
-				    size_t n)
+static inline bool vf610_nfc_kernel_is_little_endian(void)
 {
-	/*
-	 * Use this accessor for the internal SRAM buffers. On the ARM
-	 * Freescale Vybrid SoC it's known that the driver can treat
-	 * the SRAM buffer as if it's memory. Other platform might need
-	 * to treat the buffers differently.
-	 *
-	 * For the time being, use memcpy
-	 */
-	memcpy(dst, src, n);
+#ifdef __LITTLE_ENDIAN
+	return true;
+#else
+	return false;
+#endif
+}
+
+/**
+ * Read accessor for internal SRAM buffer
+ * @dst: destination address in regular memory
+ * @src: source address in SRAM buffer
+ * @len: bytes to copy
+ * @fix_endian: Fix endianness if required
+ *
+ * Use this accessor for the internal SRAM buffers. On the ARM
+ * Freescale Vybrid SoC it's known that the driver can treat
+ * the SRAM buffer as if it's memory. Other platform might need
+ * to treat the buffers differently.
+ *
+ * The controller stores bytes from the NAND chip internally in big
+ * endianness. On little endian platforms such as Vybrid this leads
+ * to reversed byte order.
+ * For performance reason (and earlier probably due to unawareness)
+ * the driver avoids correcting endianness where it has control over
+ * write and read side (e.g. page wise data access).
+ */
+static inline void vf610_nfc_rd_from_sram(void *dst, const void __iomem *src,
+					  size_t len, bool fix_endian)
+{
+	if (vf610_nfc_kernel_is_little_endian() && fix_endian) {
+		unsigned int i;
+
+		for (i = 0; i < len; i += 4) {
+			u32 val = swab32(__raw_readl(src + i));
+
+			memcpy(dst + i, &val, min(sizeof(val), len - i));
+		}
+	} else {
+		memcpy_fromio(dst, src, len);
+	}
+}
+
+/**
+ * Write accessor for internal SRAM buffer
+ * @dst: destination address in SRAM buffer
+ * @src: source address in regular memory
+ * @len: bytes to copy
+ * @fix_endian: Fix endianness if required
+ *
+ * Use this accessor for the internal SRAM buffers. On the ARM
+ * Freescale Vybrid SoC it's known that the driver can treat
+ * the SRAM buffer as if it's memory. Other platform might need
+ * to treat the buffers differently.
+ *
+ * The controller stores bytes from the NAND chip internally in big
+ * endianness. On little endian platforms such as Vybrid this leads
+ * to reversed byte order.
+ * For performance reason (and earlier probably due to unawareness)
+ * the driver avoids correcting endianness where it has control over
+ * write and read side (e.g. page wise data access).
+ */
+static inline void vf610_nfc_wr_to_sram(void __iomem *dst, const void *src,
+					size_t len, bool fix_endian)
+{
+	if (vf610_nfc_kernel_is_little_endian() && fix_endian) {
+		unsigned int i;
+
+		for (i = 0; i < len; i += 4) {
+			u32 val;
+
+			memcpy(&val, src + i, min(sizeof(val), len - i));
+			__raw_writel(swab32(val), dst + i);
+		}
+	} else {
+		memcpy_toio(dst, src, len);
+	}
 }
 
 /* Clear flags for upcoming command */
@@ -243,250 +314,185 @@ static void vf610_nfc_done(struct vf610_nfc *nfc)
 	vf610_nfc_clear_status(nfc);
 }
 
-static u8 vf610_nfc_get_id(struct vf610_nfc *nfc, int col)
+static irqreturn_t vf610_nfc_irq(int irq, void *data)
 {
-	u32 flash_id;
+	struct mtd_info *mtd = data;
+	struct vf610_nfc *nfc = mtd_to_nfc(mtd);
 
-	if (col < 4) {
-		flash_id = vf610_nfc_read(nfc, NFC_FLASH_STATUS1);
-		flash_id >>= (3 - col) * 8;
-	} else {
-		flash_id = vf610_nfc_read(nfc, NFC_FLASH_STATUS2);
-		flash_id >>= 24;
-	}
+	vf610_nfc_clear(nfc, NFC_IRQ_STATUS, IDLE_EN_BIT);
+	complete(&nfc->cmd_done);
 
-	return flash_id & 0xff;
+	return IRQ_HANDLED;
 }
 
-static u8 vf610_nfc_get_status(struct vf610_nfc *nfc)
+static inline void vf610_nfc_ecc_mode(struct vf610_nfc *nfc, int ecc_mode)
 {
-	return vf610_nfc_read(nfc, NFC_FLASH_STATUS2) & STATUS_BYTE1_MASK;
+	vf610_nfc_set_field(nfc, NFC_FLASH_CONFIG,
+			    CONFIG_ECC_MODE_MASK,
+			    CONFIG_ECC_MODE_SHIFT, ecc_mode);
 }
 
-static void vf610_nfc_send_command(struct vf610_nfc *nfc, u32 cmd_byte1,
-				   u32 cmd_code)
+static inline void vf610_nfc_transfer_size(struct vf610_nfc *nfc, int size)
 {
-	u32 tmp;
-
-	vf610_nfc_clear_status(nfc);
-
-	tmp = vf610_nfc_read(nfc, NFC_FLASH_CMD2);
-	tmp &= ~(CMD_BYTE1_MASK | CMD_CODE_MASK | BUFNO_MASK);
-	tmp |= cmd_byte1 << CMD_BYTE1_SHIFT;
-	tmp |= cmd_code << CMD_CODE_SHIFT;
-	vf610_nfc_write(nfc, NFC_FLASH_CMD2, tmp);
+	vf610_nfc_write(nfc, NFC_SECTOR_SIZE, size);
 }
 
-static void vf610_nfc_send_commands(struct vf610_nfc *nfc, u32 cmd_byte1,
-				    u32 cmd_byte2, u32 cmd_code)
+static inline void vf610_nfc_run(struct vf610_nfc *nfc, u32 col, u32 row,
+				 u32 cmd1, u32 cmd2, u32 trfr_sz)
 {
-	u32 tmp;
+	vf610_nfc_set_field(nfc, NFC_COL_ADDR, COL_ADDR_MASK,
+			    COL_ADDR_SHIFT, col);
+
+	vf610_nfc_set_field(nfc, NFC_ROW_ADDR, ROW_ADDR_MASK,
+			    ROW_ADDR_SHIFT, row);
+
+	vf610_nfc_write(nfc, NFC_SECTOR_SIZE, trfr_sz);
+	vf610_nfc_write(nfc, NFC_FLASH_CMD1, cmd1);
+	vf610_nfc_write(nfc, NFC_FLASH_CMD2, cmd2);
 
-	vf610_nfc_send_command(nfc, cmd_byte1, cmd_code);
+	dev_dbg(nfc->dev,
+		"col 0x%04x, row 0x%08x, cmd1 0x%08x, cmd2 0x%08x, len %d\n",
+		col, row, cmd1, cmd2, trfr_sz);
 
-	tmp = vf610_nfc_read(nfc, NFC_FLASH_CMD1);
-	tmp &= ~CMD_BYTE2_MASK;
-	tmp |= cmd_byte2 << CMD_BYTE2_SHIFT;
-	vf610_nfc_write(nfc, NFC_FLASH_CMD1, tmp);
+	vf610_nfc_done(nfc);
 }
 
-static irqreturn_t vf610_nfc_irq(int irq, void *data)
+static inline const struct nand_op_instr *
+vf610_get_next_instr(const struct nand_subop *subop, int *op_id)
 {
-	struct mtd_info *mtd = data;
-	struct vf610_nfc *nfc = mtd_to_nfc(mtd);
+	if (*op_id + 1 >= subop->ninstrs)
+		return NULL;
 
-	vf610_nfc_clear(nfc, NFC_IRQ_STATUS, IDLE_EN_BIT);
-	complete(&nfc->cmd_done);
+	(*op_id)++;
 
-	return IRQ_HANDLED;
+	return &subop->instrs[*op_id];
 }
 
-static void vf610_nfc_addr_cycle(struct vf610_nfc *nfc, int column, int page)
+static int vf610_nfc_cmd(struct nand_chip *chip,
+			 const struct nand_subop *subop)
 {
-	if (column != -1) {
-		if (nfc->chip.options & NAND_BUSWIDTH_16)
-			column = column / 2;
-		vf610_nfc_set_field(nfc, NFC_COL_ADDR, COL_ADDR_MASK,
-				    COL_ADDR_SHIFT, column);
+	const struct nand_op_instr *instr;
+	struct vf610_nfc *nfc = chip_to_nfc(chip);
+	int op_id = -1, trfr_sz = 0, offset;
+	u32 col = 0, row = 0, cmd1 = 0, cmd2 = 0, code = 0;
+	bool force8bit = false;
+
+	/*
+	 * Some ops are optional, but the hardware requires the operations
+	 * to be in this exact order.
+	 * The op parser enforces the order and makes sure that there isn't
+	 * a read and write element in a single operation.
+	 */
+	instr = vf610_get_next_instr(subop, &op_id);
+	if (!instr)
+		return -EINVAL;
+
+	if (instr && instr->type == NAND_OP_CMD_INSTR) {
+		cmd2 |= instr->ctx.cmd.opcode << CMD_BYTE1_SHIFT;
+		code |= COMMAND_CMD_BYTE1;
+
+		instr = vf610_get_next_instr(subop, &op_id);
 	}
-	if (page != -1)
-		vf610_nfc_set_field(nfc, NFC_ROW_ADDR, ROW_ADDR_MASK,
-				    ROW_ADDR_SHIFT, page);
-}
 
-static inline void vf610_nfc_ecc_mode(struct vf610_nfc *nfc, int ecc_mode)
-{
-	vf610_nfc_set_field(nfc, NFC_FLASH_CONFIG,
-			    CONFIG_ECC_MODE_MASK,
-			    CONFIG_ECC_MODE_SHIFT, ecc_mode);
-}
+	if (instr && instr->type == NAND_OP_ADDR_INSTR) {
+		int naddrs = nand_subop_get_num_addr_cyc(subop, op_id);
+		int i = nand_subop_get_addr_start_off(subop, op_id);
 
-static inline void vf610_nfc_transfer_size(struct vf610_nfc *nfc, int size)
-{
-	vf610_nfc_write(nfc, NFC_SECTOR_SIZE, size);
-}
+		for (; i < naddrs; i++) {
+			u8 val = instr->ctx.addr.addrs[i];
 
-static void vf610_nfc_command(struct mtd_info *mtd, unsigned command,
-			      int column, int page)
-{
-	struct vf610_nfc *nfc = mtd_to_nfc(mtd);
-	int trfr_sz = nfc->chip.options & NAND_BUSWIDTH_16 ? 1 : 0;
+			if (i < 2)
+				col |= COL_ADDR(i, val);
+			else
+				row |= ROW_ADDR(i - 2, val);
+		}
+		code |= COMMAND_NADDR_BYTES(naddrs);
 
-	nfc->buf_offset = max(column, 0);
-	nfc->alt_buf = ALT_BUF_DATA;
+		instr = vf610_get_next_instr(subop, &op_id);
+	}
 
-	switch (command) {
-	case NAND_CMD_SEQIN:
-		/* Use valid column/page from preread... */
-		vf610_nfc_addr_cycle(nfc, column, page);
-		nfc->buf_offset = 0;
+	if (instr && instr->type == NAND_OP_DATA_OUT_INSTR) {
+		trfr_sz = nand_subop_get_data_len(subop, op_id);
+		offset = nand_subop_get_data_start_off(subop, op_id);
+		force8bit = instr->ctx.data.force_8bit;
 
 		/*
-		 * SEQIN => data => PAGEPROG sequence is done by the controller
-		 * hence we do not need to issue the command here...
+		 * Don't fix endianness on page access for historical reasons.
+		 * See comment in vf610_nfc_wr_to_sram
 		 */
-		return;
-	case NAND_CMD_PAGEPROG:
-		trfr_sz += nfc->write_sz;
-		vf610_nfc_transfer_size(nfc, trfr_sz);
-		vf610_nfc_send_commands(nfc, NAND_CMD_SEQIN,
-					command, PROGRAM_PAGE_CMD_CODE);
-		if (nfc->use_hw_ecc)
-			vf610_nfc_ecc_mode(nfc, nfc->ecc_mode);
-		else
-			vf610_nfc_ecc_mode(nfc, ECC_BYPASS);
-		break;
-
-	case NAND_CMD_RESET:
-		vf610_nfc_transfer_size(nfc, 0);
-		vf610_nfc_send_command(nfc, command, RESET_CMD_CODE);
-		break;
-
-	case NAND_CMD_READOOB:
-		trfr_sz += mtd->oobsize;
-		column = mtd->writesize;
-		vf610_nfc_transfer_size(nfc, trfr_sz);
-		vf610_nfc_send_commands(nfc, NAND_CMD_READ0,
-					NAND_CMD_READSTART, READ_PAGE_CMD_CODE);
-		vf610_nfc_addr_cycle(nfc, column, page);
-		vf610_nfc_ecc_mode(nfc, ECC_BYPASS);
-		break;
-
-	case NAND_CMD_READ0:
-		trfr_sz += mtd->writesize + mtd->oobsize;
-		vf610_nfc_transfer_size(nfc, trfr_sz);
-		vf610_nfc_send_commands(nfc, NAND_CMD_READ0,
-					NAND_CMD_READSTART, READ_PAGE_CMD_CODE);
-		vf610_nfc_addr_cycle(nfc, column, page);
-		vf610_nfc_ecc_mode(nfc, nfc->ecc_mode);
-		break;
-
-	case NAND_CMD_PARAM:
-		nfc->alt_buf = ALT_BUF_ONFI;
-		trfr_sz = 3 * sizeof(struct nand_onfi_params);
-		vf610_nfc_transfer_size(nfc, trfr_sz);
-		vf610_nfc_send_command(nfc, command, READ_ONFI_PARAM_CMD_CODE);
-		vf610_nfc_addr_cycle(nfc, -1, column);
-		vf610_nfc_ecc_mode(nfc, ECC_BYPASS);
-		break;
-
-	case NAND_CMD_ERASE1:
-		vf610_nfc_transfer_size(nfc, 0);
-		vf610_nfc_send_commands(nfc, command,
-					NAND_CMD_ERASE2, ERASE_CMD_CODE);
-		vf610_nfc_addr_cycle(nfc, column, page);
-		break;
-
-	case NAND_CMD_READID:
-		nfc->alt_buf = ALT_BUF_ID;
-		nfc->buf_offset = 0;
-		vf610_nfc_transfer_size(nfc, 0);
-		vf610_nfc_send_command(nfc, command, READ_ID_CMD_CODE);
-		vf610_nfc_addr_cycle(nfc, -1, column);
-		break;
-
-	case NAND_CMD_STATUS:
-		nfc->alt_buf = ALT_BUF_STAT;
-		vf610_nfc_transfer_size(nfc, 0);
-		vf610_nfc_send_command(nfc, command, STATUS_READ_CMD_CODE);
-		break;
-	default:
-		return;
+		vf610_nfc_wr_to_sram(nfc->regs + NFC_MAIN_AREA(0) + offset,
+				     instr->ctx.data.buf.out + offset,
+				     trfr_sz, !nfc->data_access);
+		code |= COMMAND_WRITE_DATA;
+
+		instr = vf610_get_next_instr(subop, &op_id);
 	}
 
-	vf610_nfc_done(nfc);
+	if (instr && instr->type == NAND_OP_CMD_INSTR) {
+		cmd1 |= instr->ctx.cmd.opcode << CMD_BYTE2_SHIFT;
+		code |= COMMAND_CMD_BYTE2;
 
-	nfc->use_hw_ecc = false;
-	nfc->write_sz = 0;
-}
+		instr = vf610_get_next_instr(subop, &op_id);
+	}
 
-static void vf610_nfc_read_buf(struct mtd_info *mtd, u_char *buf, int len)
-{
-	struct vf610_nfc *nfc = mtd_to_nfc(mtd);
-	uint c = nfc->buf_offset;
+	if (instr && instr->type == NAND_OP_WAITRDY_INSTR) {
+		code |= COMMAND_RB_HANDSHAKE;
 
-	/* Alternate buffers are only supported through read_byte */
-	WARN_ON(nfc->alt_buf);
+		instr = vf610_get_next_instr(subop, &op_id);
+	}
 
-	vf610_nfc_memcpy(buf, nfc->regs + NFC_MAIN_AREA(0) + c, len);
+	if (instr && instr->type == NAND_OP_DATA_IN_INSTR) {
+		trfr_sz = nand_subop_get_data_len(subop, op_id);
+		offset = nand_subop_get_data_start_off(subop, op_id);
+		force8bit = instr->ctx.data.force_8bit;
 
-	nfc->buf_offset += len;
-}
+		code |= COMMAND_READ_DATA;
+	}
 
-static void vf610_nfc_write_buf(struct mtd_info *mtd, const uint8_t *buf,
-				int len)
-{
-	struct vf610_nfc *nfc = mtd_to_nfc(mtd);
-	uint c = nfc->buf_offset;
-	uint l;
+	if (force8bit && (chip->options & NAND_BUSWIDTH_16))
+		vf610_nfc_clear(nfc, NFC_FLASH_CONFIG, CONFIG_16BIT);
 
-	l = min_t(uint, len, mtd->writesize + mtd->oobsize - c);
-	vf610_nfc_memcpy(nfc->regs + NFC_MAIN_AREA(0) + c, buf, l);
+	cmd2 |= code << CMD_CODE_SHIFT;
 
-	nfc->write_sz += l;
-	nfc->buf_offset += l;
-}
+	vf610_nfc_run(nfc, col, row, cmd1, cmd2, trfr_sz);
 
-static uint8_t vf610_nfc_read_byte(struct mtd_info *mtd)
-{
-	struct vf610_nfc *nfc = mtd_to_nfc(mtd);
-	u8 tmp;
-	uint c = nfc->buf_offset;
-
-	switch (nfc->alt_buf) {
-	case ALT_BUF_ID:
-		tmp = vf610_nfc_get_id(nfc, c);
-		break;
-	case ALT_BUF_STAT:
-		tmp = vf610_nfc_get_status(nfc);
-		break;
-#ifdef __LITTLE_ENDIAN
-	case ALT_BUF_ONFI:
-		/* Reverse byte since the controller uses big endianness */
-		c = nfc->buf_offset ^ 0x3;
-		/* fall-through */
-#endif
-	default:
-		tmp = *((u8 *)(nfc->regs + NFC_MAIN_AREA(0) + c));
-		break;
+	if (instr && instr->type == NAND_OP_DATA_IN_INSTR) {
+		/*
+		 * Don't fix endianness on page access for historical reasons.
+		 * See comment in vf610_nfc_rd_from_sram
+		 */
+		vf610_nfc_rd_from_sram(instr->ctx.data.buf.in + offset,
+				       nfc->regs + NFC_MAIN_AREA(0) + offset,
+				       trfr_sz, !nfc->data_access);
 	}
-	nfc->buf_offset++;
-	return tmp;
-}
 
-static u16 vf610_nfc_read_word(struct mtd_info *mtd)
-{
-	u16 tmp;
+	if (force8bit && (chip->options & NAND_BUSWIDTH_16))
+		vf610_nfc_set(nfc, NFC_FLASH_CONFIG, CONFIG_16BIT);
 
-	vf610_nfc_read_buf(mtd, (u_char *)&tmp, sizeof(tmp));
-	return tmp;
+	return 0;
 }
 
-/* If not provided, upper layers apply a fixed delay. */
-static int vf610_nfc_dev_ready(struct mtd_info *mtd)
+static const struct nand_op_parser vf610_nfc_op_parser = NAND_OP_PARSER(
+	NAND_OP_PARSER_PATTERN(vf610_nfc_cmd,
+		NAND_OP_PARSER_PAT_CMD_ELEM(true),
+		NAND_OP_PARSER_PAT_ADDR_ELEM(true, 5),
+		NAND_OP_PARSER_PAT_DATA_OUT_ELEM(true, PAGE_2K + OOB_MAX),
+		NAND_OP_PARSER_PAT_CMD_ELEM(true),
+		NAND_OP_PARSER_PAT_WAITRDY_ELEM(true)),
+	NAND_OP_PARSER_PATTERN(vf610_nfc_cmd,
+		NAND_OP_PARSER_PAT_CMD_ELEM(true),
+		NAND_OP_PARSER_PAT_ADDR_ELEM(true, 5),
+		NAND_OP_PARSER_PAT_CMD_ELEM(true),
+		NAND_OP_PARSER_PAT_WAITRDY_ELEM(true),
+		NAND_OP_PARSER_PAT_DATA_IN_ELEM(true, PAGE_2K + OOB_MAX)),
+	);
+
+static int vf610_nfc_exec_op(struct nand_chip *chip,
+			     const struct nand_operation *op,
+			     bool check_only)
 {
-	/* NFC handles R/B internally; always ready.  */
-	return 1;
+	return nand_op_parser_exec_op(chip, &vf610_nfc_op_parser, op,
+				      check_only);
 }
 
 /*
@@ -511,21 +517,6 @@ static void vf610_nfc_select_chip(struct mtd_info *mtd, int chip)
 	vf610_nfc_write(nfc, NFC_ROW_ADDR, tmp);
 }
 
-/* Count the number of 0's in buff up to max_bits */
-static inline int count_written_bits(uint8_t *buff, int size, int max_bits)
-{
-	uint32_t *buff32 = (uint32_t *)buff;
-	int k, written_bits = 0;
-
-	for (k = 0; k < (size / 4); k++) {
-		written_bits += hweight32(~buff32[k]);
-		if (unlikely(written_bits > max_bits))
-			break;
-	}
-
-	return written_bits;
-}
-
 static inline int vf610_nfc_correct_data(struct mtd_info *mtd, uint8_t *dat,
 					 uint8_t *oob, int page)
 {
@@ -541,9 +532,9 @@ static inline int vf610_nfc_correct_data(struct mtd_info *mtd, uint8_t *dat,
 	if (!(ecc_status & ECC_STATUS_MASK))
 		return ecc_count;
 
-	/* Read OOB without ECC unit enabled */
-	vf610_nfc_command(mtd, NAND_CMD_READOOB, 0, page);
-	vf610_nfc_read_buf(mtd, oob, mtd->oobsize);
+	nfc->data_access = true;
+	nand_read_oob_op(&nfc->chip, page, 0, oob, mtd->oobsize);
+	nfc->data_access = false;
 
 	/*
 	 * On an erased page, bit count (including OOB) should be zero or
@@ -554,15 +545,51 @@ static inline int vf610_nfc_correct_data(struct mtd_info *mtd, uint8_t *dat,
 					   flips_threshold);
 }
 
+static void vf610_nfc_fill_row(struct nand_chip *chip, int page, u32 *code,
+			       u32 *row)
+{
+	*row = ROW_ADDR(0, page & 0xff) | ROW_ADDR(1, page >> 8);
+	*code |= COMMAND_RAR_BYTE1 | COMMAND_RAR_BYTE2;
+
+	if (chip->options & NAND_ROW_ADDR_3) {
+		*row |= ROW_ADDR(2, page >> 16);
+		*code |= COMMAND_RAR_BYTE3;
+	}
+}
+
 static int vf610_nfc_read_page(struct mtd_info *mtd, struct nand_chip *chip,
 				uint8_t *buf, int oob_required, int page)
 {
-	int eccsize = chip->ecc.size;
+	struct vf610_nfc *nfc = mtd_to_nfc(mtd);
+	int trfr_sz = mtd->writesize + mtd->oobsize;
+	u32 row = 0, cmd1 = 0, cmd2 = 0, code = 0;
 	int stat;
 
-	nand_read_page_op(chip, page, 0, buf, eccsize);
+	cmd2 |= NAND_CMD_READ0 << CMD_BYTE1_SHIFT;
+	code |= COMMAND_CMD_BYTE1 | COMMAND_CAR_BYTE1 | COMMAND_CAR_BYTE2;
+
+	vf610_nfc_fill_row(chip, page, &code, &row);
+
+	cmd1 |= NAND_CMD_READSTART << CMD_BYTE2_SHIFT;
+	code |= COMMAND_CMD_BYTE2 | COMMAND_RB_HANDSHAKE | COMMAND_READ_DATA;
+
+	cmd2 |= code << CMD_CODE_SHIFT;
+
+	vf610_nfc_ecc_mode(nfc, nfc->ecc_mode);
+	vf610_nfc_run(nfc, 0, row, cmd1, cmd2, trfr_sz);
+	vf610_nfc_ecc_mode(nfc, ECC_BYPASS);
+
+	/*
+	 * Don't fix endianness on page access for historical reasons.
+	 * See comment in vf610_nfc_rd_from_sram
+	 */
+	vf610_nfc_rd_from_sram(buf, nfc->regs + NFC_MAIN_AREA(0),
+			       mtd->writesize, false);
 	if (oob_required)
-		vf610_nfc_read_buf(mtd, chip->oob_poi, mtd->oobsize);
+		vf610_nfc_rd_from_sram(chip->oob_poi,
+				       nfc->regs + NFC_MAIN_AREA(0) +
+						   mtd->writesize,
+				       mtd->oobsize, false);
 
 	stat = vf610_nfc_correct_data(mtd, buf, chip->oob_poi, page);
 
@@ -579,14 +606,103 @@ static int vf610_nfc_write_page(struct mtd_info *mtd, struct nand_chip *chip,
 				const uint8_t *buf, int oob_required, int page)
 {
 	struct vf610_nfc *nfc = mtd_to_nfc(mtd);
+	int trfr_sz = mtd->writesize + mtd->oobsize;
+	u32 row = 0, cmd1 = 0, cmd2 = 0, code = 0;
+	u8 status;
+	int ret;
 
-	nand_prog_page_begin_op(chip, page, 0, buf, mtd->writesize);
-	if (oob_required)
-		vf610_nfc_write_buf(mtd, chip->oob_poi, mtd->oobsize);
+	cmd2 |= NAND_CMD_SEQIN << CMD_BYTE1_SHIFT;
+	code |= COMMAND_CMD_BYTE1 | COMMAND_CAR_BYTE1 | COMMAND_CAR_BYTE2;
+
+	vf610_nfc_fill_row(chip, page, &code, &row);
+
+	cmd1 |= NAND_CMD_PAGEPROG << CMD_BYTE2_SHIFT;
+	code |= COMMAND_CMD_BYTE2 | COMMAND_WRITE_DATA;
+
+	/*
+	 * Don't fix endianness on page access for historical reasons.
+	 * See comment in vf610_nfc_wr_to_sram
+	 */
+	vf610_nfc_wr_to_sram(nfc->regs + NFC_MAIN_AREA(0), buf,
+			     mtd->writesize, false);
+
+	code |= COMMAND_RB_HANDSHAKE;
+	cmd2 |= code << CMD_CODE_SHIFT;
+
+	vf610_nfc_ecc_mode(nfc, nfc->ecc_mode);
+	vf610_nfc_run(nfc, 0, row, cmd1, cmd2, trfr_sz);
+	vf610_nfc_ecc_mode(nfc, ECC_BYPASS);
+
+	ret = nand_status_op(chip, &status);
+	if (ret)
+		return ret;
+
+	if (status & NAND_STATUS_FAIL)
+		return -EIO;
+
+	return 0;
+}
+
+static int vf610_nfc_read_page_raw(struct mtd_info *mtd,
+				   struct nand_chip *chip, u8 *buf,
+				   int oob_required, int page)
+{
+	struct vf610_nfc *nfc = mtd_to_nfc(mtd);
+	int ret;
+
+	nfc->data_access = true;
+	ret = nand_read_page_raw(mtd, chip, buf, oob_required, page);
+	nfc->data_access = false;
+
+	return ret;
+}
+
+static int vf610_nfc_write_page_raw(struct mtd_info *mtd,
+				    struct nand_chip *chip, const u8 *buf,
+				    int oob_required, int page)
+{
+	struct vf610_nfc *nfc = mtd_to_nfc(mtd);
+	int ret;
+
+	nfc->data_access = true;
+	ret = nand_prog_page_begin_op(chip, page, 0, buf, mtd->writesize);
+	if (!ret && oob_required)
+		ret = nand_write_data_op(chip, chip->oob_poi, mtd->oobsize,
+					 false);
+	nfc->data_access = false;
 
-	/* Always write whole page including OOB due to HW ECC */
-	nfc->use_hw_ecc = true;
-	nfc->write_sz = mtd->writesize + mtd->oobsize;
+	if (ret)
+		return ret;
+
+	return nand_prog_page_end_op(chip);
+}
+
+static int vf610_nfc_read_oob(struct mtd_info *mtd, struct nand_chip *chip,
+			      int page)
+{
+	struct vf610_nfc *nfc = mtd_to_nfc(mtd);
+	int ret;
+
+	nfc->data_access = true;
+	ret = nand_read_oob_std(mtd, chip, page);
+	nfc->data_access = false;
+
+	return ret;
+}
+
+static int vf610_nfc_write_oob(struct mtd_info *mtd, struct nand_chip *chip,
+			       int page)
+{
+	struct vf610_nfc *nfc = mtd_to_nfc(mtd);
+	int ret;
+
+	nfc->data_access = true;
+	ret = nand_prog_page_begin_op(chip, page, mtd->writesize,
+				      chip->oob_poi, mtd->oobsize);
+	nfc->data_access = false;
+
+	if (ret)
+		return ret;
 
 	return nand_prog_page_end_op(chip);
 }
@@ -605,6 +721,7 @@ static void vf610_nfc_preinit_controller(struct vf610_nfc *nfc)
 	vf610_nfc_clear(nfc, NFC_FLASH_CONFIG, CONFIG_BOOT_MODE_BIT);
 	vf610_nfc_clear(nfc, NFC_FLASH_CONFIG, CONFIG_DMA_REQ_BIT);
 	vf610_nfc_set(nfc, NFC_FLASH_CONFIG, CONFIG_FAST_FLASH_BIT);
+	vf610_nfc_ecc_mode(nfc, ECC_BYPASS);
 
 	/* Disable virtual pages, only one elementary transfer unit */
 	vf610_nfc_set_field(nfc, NFC_FLASH_CONFIG, CONFIG_PAGE_CNT_MASK,
@@ -682,7 +799,7 @@ static int vf610_nfc_probe(struct platform_device *pdev)
 				dev_err(nfc->dev,
 					"Only one NAND chip supported!\n");
 				err = -EINVAL;
-				goto error;
+				goto err_disable_clk;
 			}
 
 			nand_set_flash_node(chip, child);
@@ -692,18 +809,11 @@ static int vf610_nfc_probe(struct platform_device *pdev)
 	if (!nand_get_flash_node(chip)) {
 		dev_err(nfc->dev, "NAND chip sub-node missing!\n");
 		err = -ENODEV;
-		goto err_clk;
+		goto err_disable_clk;
 	}
 
-	chip->dev_ready = vf610_nfc_dev_ready;
-	chip->cmdfunc = vf610_nfc_command;
-	chip->read_byte = vf610_nfc_read_byte;
-	chip->read_word = vf610_nfc_read_word;
-	chip->read_buf = vf610_nfc_read_buf;
-	chip->write_buf = vf610_nfc_write_buf;
+	chip->exec_op = vf610_nfc_exec_op;
 	chip->select_chip = vf610_nfc_select_chip;
-	chip->onfi_set_features = nand_onfi_get_set_features_notsupp;
-	chip->onfi_get_features = nand_onfi_get_set_features_notsupp;
 
 	chip->options |= NAND_NO_SUBPAGE_WRITE;
 
@@ -712,7 +822,7 @@ static int vf610_nfc_probe(struct platform_device *pdev)
 	err = devm_request_irq(nfc->dev, irq, vf610_nfc_irq, 0, DRV_NAME, mtd);
 	if (err) {
 		dev_err(nfc->dev, "Error requesting IRQ!\n");
-		goto error;
+		goto err_disable_clk;
 	}
 
 	vf610_nfc_preinit_controller(nfc);
@@ -720,7 +830,7 @@ static int vf610_nfc_probe(struct platform_device *pdev)
 	/* first scan to find the device and get the page size */
 	err = nand_scan_ident(mtd, 1, NULL);
 	if (err)
-		goto error;
+		goto err_disable_clk;
 
 	vf610_nfc_init_controller(nfc);
 
@@ -732,20 +842,20 @@ static int vf610_nfc_probe(struct platform_device *pdev)
 	if (mtd->writesize + mtd->oobsize > PAGE_2K + OOB_MAX - 8) {
 		dev_err(nfc->dev, "Unsupported flash page size\n");
 		err = -ENXIO;
-		goto error;
+		goto err_disable_clk;
 	}
 
 	if (chip->ecc.mode == NAND_ECC_HW) {
 		if (mtd->writesize != PAGE_2K && mtd->oobsize < 64) {
 			dev_err(nfc->dev, "Unsupported flash with hwecc\n");
 			err = -ENXIO;
-			goto error;
+			goto err_disable_clk;
 		}
 
 		if (chip->ecc.size != mtd->writesize) {
 			dev_err(nfc->dev, "Step size needs to be page size\n");
 			err = -ENXIO;
-			goto error;
+			goto err_disable_clk;
 		}
 
 		/* Only 64 byte ECC layouts known */
@@ -763,11 +873,15 @@ static int vf610_nfc_probe(struct platform_device *pdev)
 		} else {
 			dev_err(nfc->dev, "Unsupported ECC strength\n");
 			err = -ENXIO;
-			goto error;
+			goto err_disable_clk;
 		}
 
 		chip->ecc.read_page = vf610_nfc_read_page;
 		chip->ecc.write_page = vf610_nfc_write_page;
+		chip->ecc.read_page_raw = vf610_nfc_read_page_raw;
+		chip->ecc.write_page_raw = vf610_nfc_write_page_raw;
+		chip->ecc.read_oob = vf610_nfc_read_oob;
+		chip->ecc.write_oob = vf610_nfc_write_oob;
 
 		chip->ecc.size = PAGE_2K;
 	}
@@ -775,16 +889,19 @@ static int vf610_nfc_probe(struct platform_device *pdev)
 	/* second phase scan */
 	err = nand_scan_tail(mtd);
 	if (err)
-		goto error;
+		goto err_disable_clk;
 
 	platform_set_drvdata(pdev, mtd);
 
 	/* Register device in MTD */
-	return mtd_device_register(mtd, NULL, 0);
+	err = mtd_device_register(mtd, NULL, 0);
+	if (err)
+		goto err_cleanup_nand;
+	return 0;
 
-error:
-	of_node_put(nand_get_flash_node(chip));
-err_clk:
+err_cleanup_nand:
+	nand_cleanup(chip);
+err_disable_clk:
 	clk_disable_unprepare(nfc->clk);
 	return err;
 }
diff --git a/drivers/mtd/nand/xway_nand.c b/drivers/mtd/nand/raw/xway_nand.c
index 9926b4e3d69d..9926b4e3d69d 100644
--- a/drivers/mtd/nand/xway_nand.c
+++ b/drivers/mtd/nand/raw/xway_nand.c