diff options
Diffstat (limited to 'drivers/net/bnx2x/bnx2x_link.c')
| -rw-r--r-- | drivers/net/bnx2x/bnx2x_link.c | 2527 |
1 files changed, 1359 insertions, 1168 deletions
diff --git a/drivers/net/bnx2x/bnx2x_link.c b/drivers/net/bnx2x/bnx2x_link.c index dd1210fddfff..f2f367d4e74d 100644 --- a/drivers/net/bnx2x/bnx2x_link.c +++ b/drivers/net/bnx2x/bnx2x_link.c @@ -1,4 +1,4 @@ -/* Copyright 2008-2009 Broadcom Corporation +/* Copyright 2008-2011 Broadcom Corporation * * Unless you and Broadcom execute a separate written software license * agreement governing use of this software, this software is licensed to you @@ -28,12 +28,13 @@ /********************************************************/ #define ETH_HLEN 14 -#define ETH_OVREHEAD (ETH_HLEN + 8 + 8)/* 16 for CRC + VLAN + LLC */ +/* L2 header size + 2*VLANs (8 bytes) + LLC SNAP (8 bytes) */ +#define ETH_OVREHEAD (ETH_HLEN + 8 + 8) #define ETH_MIN_PACKET_SIZE 60 #define ETH_MAX_PACKET_SIZE 1500 #define ETH_MAX_JUMBO_PACKET_SIZE 9600 #define MDIO_ACCESS_TIMEOUT 1000 -#define BMAC_CONTROL_RX_ENABLE 2 +#define BMAC_CONTROL_RX_ENABLE 2 /***********************************************************/ /* Shortcut definitions */ @@ -79,7 +80,7 @@ #define AUTONEG_CL37 SHARED_HW_CFG_AN_ENABLE_CL37 #define AUTONEG_CL73 SHARED_HW_CFG_AN_ENABLE_CL73 -#define AUTONEG_BAM SHARED_HW_CFG_AN_ENABLE_BAM +#define AUTONEG_BAM SHARED_HW_CFG_AN_ENABLE_BAM #define AUTONEG_PARALLEL \ SHARED_HW_CFG_AN_ENABLE_PARALLEL_DETECTION #define AUTONEG_SGMII_FIBER_AUTODET \ @@ -112,10 +113,10 @@ #define GP_STATUS_10G_KX4 \ MDIO_GP_STATUS_TOP_AN_STATUS1_ACTUAL_SPEED_10G_KX4 -#define LINK_10THD LINK_STATUS_SPEED_AND_DUPLEX_10THD -#define LINK_10TFD LINK_STATUS_SPEED_AND_DUPLEX_10TFD +#define LINK_10THD LINK_STATUS_SPEED_AND_DUPLEX_10THD +#define LINK_10TFD LINK_STATUS_SPEED_AND_DUPLEX_10TFD #define LINK_100TXHD LINK_STATUS_SPEED_AND_DUPLEX_100TXHD -#define LINK_100T4 LINK_STATUS_SPEED_AND_DUPLEX_100T4 +#define LINK_100T4 LINK_STATUS_SPEED_AND_DUPLEX_100T4 #define LINK_100TXFD LINK_STATUS_SPEED_AND_DUPLEX_100TXFD #define LINK_1000THD LINK_STATUS_SPEED_AND_DUPLEX_1000THD #define LINK_1000TFD LINK_STATUS_SPEED_AND_DUPLEX_1000TFD @@ -123,18 +124,18 @@ #define LINK_2500THD LINK_STATUS_SPEED_AND_DUPLEX_2500THD #define LINK_2500TFD LINK_STATUS_SPEED_AND_DUPLEX_2500TFD #define LINK_2500XFD LINK_STATUS_SPEED_AND_DUPLEX_2500XFD -#define LINK_10GTFD LINK_STATUS_SPEED_AND_DUPLEX_10GTFD -#define LINK_10GXFD LINK_STATUS_SPEED_AND_DUPLEX_10GXFD -#define LINK_12GTFD LINK_STATUS_SPEED_AND_DUPLEX_12GTFD -#define LINK_12GXFD LINK_STATUS_SPEED_AND_DUPLEX_12GXFD +#define LINK_10GTFD LINK_STATUS_SPEED_AND_DUPLEX_10GTFD +#define LINK_10GXFD LINK_STATUS_SPEED_AND_DUPLEX_10GXFD +#define LINK_12GTFD LINK_STATUS_SPEED_AND_DUPLEX_12GTFD +#define LINK_12GXFD LINK_STATUS_SPEED_AND_DUPLEX_12GXFD #define LINK_12_5GTFD LINK_STATUS_SPEED_AND_DUPLEX_12_5GTFD #define LINK_12_5GXFD LINK_STATUS_SPEED_AND_DUPLEX_12_5GXFD -#define LINK_13GTFD LINK_STATUS_SPEED_AND_DUPLEX_13GTFD -#define LINK_13GXFD LINK_STATUS_SPEED_AND_DUPLEX_13GXFD -#define LINK_15GTFD LINK_STATUS_SPEED_AND_DUPLEX_15GTFD -#define LINK_15GXFD LINK_STATUS_SPEED_AND_DUPLEX_15GXFD -#define LINK_16GTFD LINK_STATUS_SPEED_AND_DUPLEX_16GTFD -#define LINK_16GXFD LINK_STATUS_SPEED_AND_DUPLEX_16GXFD +#define LINK_13GTFD LINK_STATUS_SPEED_AND_DUPLEX_13GTFD +#define LINK_13GXFD LINK_STATUS_SPEED_AND_DUPLEX_13GXFD +#define LINK_15GTFD LINK_STATUS_SPEED_AND_DUPLEX_15GTFD +#define LINK_15GXFD LINK_STATUS_SPEED_AND_DUPLEX_15GXFD +#define LINK_16GTFD LINK_STATUS_SPEED_AND_DUPLEX_16GTFD +#define LINK_16GXFD LINK_STATUS_SPEED_AND_DUPLEX_16GXFD #define PHY_XGXS_FLAG 0x1 #define PHY_SGMII_FLAG 0x2 @@ -142,7 +143,7 @@ /* */ #define SFP_EEPROM_CON_TYPE_ADDR 0x2 - #define SFP_EEPROM_CON_TYPE_VAL_LC 0x7 + #define SFP_EEPROM_CON_TYPE_VAL_LC 0x7 #define SFP_EEPROM_CON_TYPE_VAL_COPPER 0x21 @@ -153,15 +154,15 @@ #define SFP_EEPROM_FC_TX_TECH_ADDR 0x8 #define SFP_EEPROM_FC_TX_TECH_BITMASK_COPPER_PASSIVE 0x4 - #define SFP_EEPROM_FC_TX_TECH_BITMASK_COPPER_ACTIVE 0x8 + #define SFP_EEPROM_FC_TX_TECH_BITMASK_COPPER_ACTIVE 0x8 -#define SFP_EEPROM_OPTIONS_ADDR 0x40 +#define SFP_EEPROM_OPTIONS_ADDR 0x40 #define SFP_EEPROM_OPTIONS_LINEAR_RX_OUT_MASK 0x1 -#define SFP_EEPROM_OPTIONS_SIZE 2 +#define SFP_EEPROM_OPTIONS_SIZE 2 -#define EDC_MODE_LINEAR 0x0022 -#define EDC_MODE_LIMITING 0x0044 -#define EDC_MODE_PASSIVE_DAC 0x0055 +#define EDC_MODE_LINEAR 0x0022 +#define EDC_MODE_LIMITING 0x0044 +#define EDC_MODE_PASSIVE_DAC 0x0055 #define ETS_BW_LIMIT_CREDIT_UPPER_BOUND (0x5000) @@ -170,24 +171,18 @@ /* INTERFACE */ /**********************************************************/ -#define CL45_WR_OVER_CL22(_bp, _phy, _bank, _addr, _val) \ +#define CL22_WR_OVER_CL45(_bp, _phy, _bank, _addr, _val) \ bnx2x_cl45_write(_bp, _phy, \ (_phy)->def_md_devad, \ (_bank + (_addr & 0xf)), \ _val) -#define CL45_RD_OVER_CL22(_bp, _phy, _bank, _addr, _val) \ +#define CL22_RD_OVER_CL45(_bp, _phy, _bank, _addr, _val) \ bnx2x_cl45_read(_bp, _phy, \ (_phy)->def_md_devad, \ (_bank + (_addr & 0xf)), \ _val) -static u8 bnx2x_cl45_read(struct bnx2x *bp, struct bnx2x_phy *phy, - u8 devad, u16 reg, u16 *ret_val); - -static u8 bnx2x_cl45_write(struct bnx2x *bp, struct bnx2x_phy *phy, - u8 devad, u16 reg, u16 val); - static u32 bnx2x_bits_en(struct bnx2x *bp, u32 reg, u32 bits) { u32 val = REG_RD(bp, reg); @@ -216,7 +211,7 @@ void bnx2x_ets_disabled(struct link_params *params) DP(NETIF_MSG_LINK, "ETS disabled configuration\n"); - /** + /* * mapping between entry priority to client number (0,1,2 -debug and * management clients, 3 - COS0 client, 4 - COS client)(HIGHEST) * 3bits client num. @@ -225,7 +220,7 @@ void bnx2x_ets_disabled(struct link_params *params) */ REG_WR(bp, NIG_REG_P0_TX_ARB_PRIORITY_CLIENT, 0x4688); - /** + /* * Bitmap of 5bits length. Each bit specifies whether the entry behaves * as strict. Bits 0,1,2 - debug and management entries, 3 - * COS0 entry, 4 - COS1 entry. @@ -237,12 +232,12 @@ void bnx2x_ets_disabled(struct link_params *params) REG_WR(bp, NIG_REG_P0_TX_ARB_CLIENT_IS_STRICT, 0x7); /* defines which entries (clients) are subjected to WFQ arbitration */ REG_WR(bp, NIG_REG_P0_TX_ARB_CLIENT_IS_SUBJECT2WFQ, 0); - /** - * For strict priority entries defines the number of consecutive - * slots for the highest priority. - */ + /* + * For strict priority entries defines the number of consecutive + * slots for the highest priority. + */ REG_WR(bp, NIG_REG_P0_TX_ARB_NUM_STRICT_ARB_SLOTS, 0x100); - /** + /* * mapping between the CREDIT_WEIGHT registers and actual client * numbers */ @@ -255,7 +250,7 @@ void bnx2x_ets_disabled(struct link_params *params) REG_WR(bp, PBF_REG_HIGH_PRIORITY_COS_NUM, 0); /* ETS mode disable */ REG_WR(bp, PBF_REG_ETS_ENABLED, 0); - /** + /* * If ETS mode is enabled (there is no strict priority) defines a WFQ * weight for COS0/COS1. */ @@ -268,24 +263,24 @@ void bnx2x_ets_disabled(struct link_params *params) REG_WR(bp, PBF_REG_NUM_STRICT_ARB_SLOTS, 0); } -void bnx2x_ets_bw_limit_common(const struct link_params *params) +static void bnx2x_ets_bw_limit_common(const struct link_params *params) { /* ETS disabled configuration */ struct bnx2x *bp = params->bp; DP(NETIF_MSG_LINK, "ETS enabled BW limit configuration\n"); - /** - * defines which entries (clients) are subjected to WFQ arbitration - * COS0 0x8 - * COS1 0x10 - */ + /* + * defines which entries (clients) are subjected to WFQ arbitration + * COS0 0x8 + * COS1 0x10 + */ REG_WR(bp, NIG_REG_P0_TX_ARB_CLIENT_IS_SUBJECT2WFQ, 0x18); - /** - * mapping between the ARB_CREDIT_WEIGHT registers and actual - * client numbers (WEIGHT_0 does not actually have to represent - * client 0) - * PRI4 | PRI3 | PRI2 | PRI1 | PRI0 - * cos1-001 cos0-000 dbg1-100 dbg0-011 MCP-010 - */ + /* + * mapping between the ARB_CREDIT_WEIGHT registers and actual + * client numbers (WEIGHT_0 does not actually have to represent + * client 0) + * PRI4 | PRI3 | PRI2 | PRI1 | PRI0 + * cos1-001 cos0-000 dbg1-100 dbg0-011 MCP-010 + */ REG_WR(bp, NIG_REG_P0_TX_ARB_CLIENT_CREDIT_MAP, 0x111A); REG_WR(bp, NIG_REG_P0_TX_ARB_CREDIT_UPPER_BOUND_0, @@ -298,14 +293,14 @@ void bnx2x_ets_bw_limit_common(const struct link_params *params) /* Defines the number of consecutive slots for the strict priority */ REG_WR(bp, PBF_REG_NUM_STRICT_ARB_SLOTS, 0); - /** - * Bitmap of 5bits length. Each bit specifies whether the entry behaves - * as strict. Bits 0,1,2 - debug and management entries, 3 - COS0 - * entry, 4 - COS1 entry. - * COS1 | COS0 | DEBUG21 | DEBUG0 | MGMT - * bit4 bit3 bit2 bit1 bit0 - * MCP and debug are strict - */ + /* + * Bitmap of 5bits length. Each bit specifies whether the entry behaves + * as strict. Bits 0,1,2 - debug and management entries, 3 - COS0 + * entry, 4 - COS1 entry. + * COS1 | COS0 | DEBUG21 | DEBUG0 | MGMT + * bit4 bit3 bit2 bit1 bit0 + * MCP and debug are strict + */ REG_WR(bp, NIG_REG_P0_TX_ARB_CLIENT_IS_STRICT, 0x7); /* Upper bound that COS0_WEIGHT can reach in the WFQ arbiter.*/ @@ -329,8 +324,7 @@ void bnx2x_ets_bw_limit(const struct link_params *params, const u32 cos0_bw, if ((0 == total_bw) || (0 == cos0_bw) || (0 == cos1_bw)) { - DP(NETIF_MSG_LINK, - "bnx2x_ets_bw_limit: Total BW can't be zero\n"); + DP(NETIF_MSG_LINK, "Total BW can't be zero\n"); return; } @@ -355,7 +349,7 @@ u8 bnx2x_ets_strict(const struct link_params *params, const u8 strict_cos) u32 val = 0; DP(NETIF_MSG_LINK, "ETS enabled strict configuration\n"); - /** + /* * Bitmap of 5bits length. Each bit specifies whether the entry behaves * as strict. Bits 0,1,2 - debug and management entries, * 3 - COS0 entry, 4 - COS1 entry. @@ -364,7 +358,7 @@ u8 bnx2x_ets_strict(const struct link_params *params, const u8 strict_cos) * MCP and debug are strict */ REG_WR(bp, NIG_REG_P0_TX_ARB_CLIENT_IS_STRICT, 0x1F); - /** + /* * For strict priority entries defines the number of consecutive slots * for the highest priority. */ @@ -377,14 +371,14 @@ u8 bnx2x_ets_strict(const struct link_params *params, const u8 strict_cos) /* Defines the number of consecutive slots for the strict priority */ REG_WR(bp, PBF_REG_HIGH_PRIORITY_COS_NUM, strict_cos); - /** - * mapping between entry priority to client number (0,1,2 -debug and - * management clients, 3 - COS0 client, 4 - COS client)(HIGHEST) - * 3bits client num. - * PRI4 | PRI3 | PRI2 | PRI1 | PRI0 - * dbg0-010 dbg1-001 cos1-100 cos0-011 MCP-000 - * dbg0-010 dbg1-001 cos0-011 cos1-100 MCP-000 - */ + /* + * mapping between entry priority to client number (0,1,2 -debug and + * management clients, 3 - COS0 client, 4 - COS client)(HIGHEST) + * 3bits client num. + * PRI4 | PRI3 | PRI2 | PRI1 | PRI0 + * dbg0-010 dbg1-001 cos1-100 cos0-011 MCP-000 + * dbg0-010 dbg1-001 cos0-011 cos1-100 MCP-000 + */ val = (0 == strict_cos) ? 0x2318 : 0x22E0; REG_WR(bp, NIG_REG_P0_TX_ARB_PRIORITY_CLIENT, val); @@ -471,7 +465,7 @@ void bnx2x_pfc_statistic(struct link_params *params, struct link_vars *vars, /* MAC/PBF section */ /******************************************************************/ static void bnx2x_emac_init(struct link_params *params, - struct link_vars *vars) + struct link_vars *vars) { /* reset and unreset the emac core */ struct bnx2x *bp = params->bp; @@ -481,10 +475,10 @@ static void bnx2x_emac_init(struct link_params *params, u16 timeout; REG_WR(bp, GRCBASE_MISC + MISC_REGISTERS_RESET_REG_2_CLEAR, - (MISC_REGISTERS_RESET_REG_2_RST_EMAC0_HARD_CORE << port)); + (MISC_REGISTERS_RESET_REG_2_RST_EMAC0_HARD_CORE << port)); udelay(5); REG_WR(bp, GRCBASE_MISC + MISC_REGISTERS_RESET_REG_2_SET, - (MISC_REGISTERS_RESET_REG_2_RST_EMAC0_HARD_CORE << port)); + (MISC_REGISTERS_RESET_REG_2_RST_EMAC0_HARD_CORE << port)); /* init emac - use read-modify-write */ /* self clear reset */ @@ -515,7 +509,7 @@ static void bnx2x_emac_init(struct link_params *params, } static u8 bnx2x_emac_enable(struct link_params *params, - struct link_vars *vars, u8 lb) + struct link_vars *vars, u8 lb) { struct bnx2x *bp = params->bp; u8 port = params->port; @@ -527,55 +521,33 @@ static u8 bnx2x_emac_enable(struct link_params *params, /* enable emac and not bmac */ REG_WR(bp, NIG_REG_EGRESS_EMAC0_PORT + port*4, 1); - /* for paladium */ - if (CHIP_REV_IS_EMUL(bp)) { - /* Use lane 1 (of lanes 0-3) */ - REG_WR(bp, NIG_REG_XGXS_LANE_SEL_P0 + port*4, 1); - REG_WR(bp, NIG_REG_XGXS_SERDES0_MODE_SEL + - port*4, 1); - } - /* for fpga */ - else - - if (CHIP_REV_IS_FPGA(bp)) { - /* Use lane 1 (of lanes 0-3) */ - DP(NETIF_MSG_LINK, "bnx2x_emac_enable: Setting FPGA\n"); - - REG_WR(bp, NIG_REG_XGXS_LANE_SEL_P0 + port*4, 1); - REG_WR(bp, NIG_REG_XGXS_SERDES0_MODE_SEL + port*4, - 0); - } else /* ASIC */ if (vars->phy_flags & PHY_XGXS_FLAG) { u32 ser_lane = ((params->lane_config & - PORT_HW_CFG_LANE_SWAP_CFG_MASTER_MASK) >> - PORT_HW_CFG_LANE_SWAP_CFG_MASTER_SHIFT); + PORT_HW_CFG_LANE_SWAP_CFG_MASTER_MASK) >> + PORT_HW_CFG_LANE_SWAP_CFG_MASTER_SHIFT); DP(NETIF_MSG_LINK, "XGXS\n"); /* select the master lanes (out of 0-3) */ - REG_WR(bp, NIG_REG_XGXS_LANE_SEL_P0 + - port*4, ser_lane); + REG_WR(bp, NIG_REG_XGXS_LANE_SEL_P0 + port*4, ser_lane); /* select XGXS */ - REG_WR(bp, NIG_REG_XGXS_SERDES0_MODE_SEL + - port*4, 1); + REG_WR(bp, NIG_REG_XGXS_SERDES0_MODE_SEL + port*4, 1); } else { /* SerDes */ DP(NETIF_MSG_LINK, "SerDes\n"); /* select SerDes */ - REG_WR(bp, NIG_REG_XGXS_SERDES0_MODE_SEL + - port*4, 0); + REG_WR(bp, NIG_REG_XGXS_SERDES0_MODE_SEL + port*4, 0); } bnx2x_bits_en(bp, emac_base + EMAC_REG_EMAC_RX_MODE, - EMAC_RX_MODE_RESET); + EMAC_RX_MODE_RESET); bnx2x_bits_en(bp, emac_base + EMAC_REG_EMAC_TX_MODE, - EMAC_TX_MODE_RESET); + EMAC_TX_MODE_RESET); if (CHIP_REV_IS_SLOW(bp)) { /* config GMII mode */ val = REG_RD(bp, emac_base + EMAC_REG_EMAC_MODE); - EMAC_WR(bp, EMAC_REG_EMAC_MODE, - (val | EMAC_MODE_PORT_GMII)); + EMAC_WR(bp, EMAC_REG_EMAC_MODE, (val | EMAC_MODE_PORT_GMII)); } else { /* ASIC */ /* pause enable/disable */ bnx2x_bits_dis(bp, emac_base + EMAC_REG_EMAC_RX_MODE, @@ -605,14 +577,14 @@ static u8 bnx2x_emac_enable(struct link_params *params, val = REG_RD(bp, emac_base + EMAC_REG_EMAC_RX_MODE); val |= EMAC_RX_MODE_KEEP_VLAN_TAG | EMAC_RX_MODE_PROMISCUOUS; - /** - * Setting this bit causes MAC control frames (except for pause - * frames) to be passed on for processing. This setting has no - * affect on the operation of the pause frames. This bit effects - * all packets regardless of RX Parser packet sorting logic. - * Turn the PFC off to make sure we are in Xon state before - * enabling it. - */ + /* + * Setting this bit causes MAC control frames (except for pause + * frames) to be passed on for processing. This setting has no + * affect on the operation of the pause frames. This bit effects + * all packets regardless of RX Parser packet sorting logic. + * Turn the PFC off to make sure we are in Xon state before + * enabling it. + */ EMAC_WR(bp, EMAC_REG_RX_PFC_MODE, 0); if (params->feature_config_flags & FEATURE_CONFIG_PFC_ENABLED) { DP(NETIF_MSG_LINK, "PFC is enabled\n"); @@ -666,16 +638,7 @@ static u8 bnx2x_emac_enable(struct link_params *params, REG_WR(bp, NIG_REG_EMAC0_PAUSE_OUT_EN + port*4, val); REG_WR(bp, NIG_REG_EGRESS_EMAC0_OUT_EN + port*4, 0x1); - if (CHIP_REV_IS_EMUL(bp)) { - /* take the BigMac out of reset */ - REG_WR(bp, - GRCBASE_MISC + MISC_REGISTERS_RESET_REG_2_SET, - (MISC_REGISTERS_RESET_REG_2_RST_BMAC0 << port)); - - /* enable access for bmac registers */ - REG_WR(bp, NIG_REG_BMAC0_REGS_OUT_EN + port*4, 0x1); - } else - REG_WR(bp, NIG_REG_BMAC0_REGS_OUT_EN + port*4, 0x0); + REG_WR(bp, NIG_REG_BMAC0_REGS_OUT_EN + port*4, 0x0); vars->mac_type = MAC_TYPE_EMAC; return 0; @@ -731,8 +694,7 @@ static void bnx2x_update_pfc_bmac2(struct link_params *params, val |= (1<<5); wb_data[0] = val; wb_data[1] = 0; - REG_WR_DMAE(bp, bmac_addr + BIGMAC2_REGISTER_RX_CONTROL, - wb_data, 2); + REG_WR_DMAE(bp, bmac_addr + BIGMAC2_REGISTER_RX_CONTROL, wb_data, 2); udelay(30); /* Tx control */ @@ -768,12 +730,12 @@ static void bnx2x_update_pfc_bmac2(struct link_params *params, REG_WR_DMAE(bp, bmac_addr + BIGMAC2_REGISTER_PFC_CONTROL, wb_data, 2); - /** - * Set Time (based unit is 512 bit time) between automatic - * re-sending of PP packets amd enable automatic re-send of - * Per-Priroity Packet as long as pp_gen is asserted and - * pp_disable is low. - */ + /* + * Set Time (based unit is 512 bit time) between automatic + * re-sending of PP packets amd enable automatic re-send of + * Per-Priroity Packet as long as pp_gen is asserted and + * pp_disable is low. + */ val = 0x8000; if (params->feature_config_flags & FEATURE_CONFIG_PFC_ENABLED) val |= (1<<16); /* enable automatic re-send */ @@ -781,7 +743,7 @@ static void bnx2x_update_pfc_bmac2(struct link_params *params, wb_data[0] = val; wb_data[1] = 0; REG_WR_DMAE(bp, bmac_addr + BIGMAC2_REGISTER_TX_PAUSE_CONTROL, - wb_data, 2); + wb_data, 2); /* mac control */ val = 0x3; /* Enable RX and TX */ @@ -795,8 +757,7 @@ static void bnx2x_update_pfc_bmac2(struct link_params *params, wb_data[0] = val; wb_data[1] = 0; - REG_WR_DMAE(bp, bmac_addr + BIGMAC2_REGISTER_BMAC_CONTROL, - wb_data, 2); + REG_WR_DMAE(bp, bmac_addr + BIGMAC2_REGISTER_BMAC_CONTROL, wb_data, 2); } static void bnx2x_update_pfc_brb(struct link_params *params, @@ -825,17 +786,25 @@ static void bnx2x_update_pfc_brb(struct link_params *params, full_xon_th = PFC_BRB_MAC_FULL_XON_THRESHOLD_NON_PAUSEABLE; } - /* The number of free blocks below which the pause signal to class 0 - of MAC #n is asserted. n=0,1 */ + /* + * The number of free blocks below which the pause signal to class 0 + * of MAC #n is asserted. n=0,1 + */ REG_WR(bp, BRB1_REG_PAUSE_0_XOFF_THRESHOLD_0 , pause_xoff_th); - /* The number of free blocks above which the pause signal to class 0 - of MAC #n is de-asserted. n=0,1 */ + /* + * The number of free blocks above which the pause signal to class 0 + * of MAC #n is de-asserted. n=0,1 + */ REG_WR(bp, BRB1_REG_PAUSE_0_XON_THRESHOLD_0 , pause_xon_th); - /* The number of free blocks below which the full signal to class 0 - of MAC #n is asserted. n=0,1 */ + /* + * The number of free blocks below which the full signal to class 0 + * of MAC #n is asserted. n=0,1 + */ REG_WR(bp, BRB1_REG_FULL_0_XOFF_THRESHOLD_0 , full_xoff_th); - /* The number of free blocks above which the full signal to class 0 - of MAC #n is de-asserted. n=0,1 */ + /* + * The number of free blocks above which the full signal to class 0 + * of MAC #n is de-asserted. n=0,1 + */ REG_WR(bp, BRB1_REG_FULL_0_XON_THRESHOLD_0 , full_xon_th); if (set_pfc && pfc_params) { @@ -859,25 +828,25 @@ static void bnx2x_update_pfc_brb(struct link_params *params, full_xon_th = PFC_BRB_MAC_FULL_XON_THRESHOLD_NON_PAUSEABLE; } - /** + /* * The number of free blocks below which the pause signal to * class 1 of MAC #n is asserted. n=0,1 - **/ + */ REG_WR(bp, BRB1_REG_PAUSE_1_XOFF_THRESHOLD_0, pause_xoff_th); - /** + /* * The number of free blocks above which the pause signal to * class 1 of MAC #n is de-asserted. n=0,1 - **/ + */ REG_WR(bp, BRB1_REG_PAUSE_1_XON_THRESHOLD_0, pause_xon_th); - /** + /* * The number of free blocks below which the full signal to * class 1 of MAC #n is asserted. n=0,1 - **/ + */ REG_WR(bp, BRB1_REG_FULL_1_XOFF_THRESHOLD_0, full_xoff_th); - /** + /* * The number of free blocks above which the full signal to * class 1 of MAC #n is de-asserted. n=0,1 - **/ + */ REG_WR(bp, BRB1_REG_FULL_1_XON_THRESHOLD_0, full_xon_th); } } @@ -896,7 +865,7 @@ static void bnx2x_update_pfc_nig(struct link_params *params, FEATURE_CONFIG_PFC_ENABLED; DP(NETIF_MSG_LINK, "updating pfc nig parameters\n"); - /** + /* * When NIG_LLH0_XCM_MASK_REG_LLHX_XCM_MASK_BCN bit is set * MAC control frames (that are not pause packets) * will be forwarded to the XCM. @@ -904,7 +873,7 @@ static void bnx2x_update_pfc_nig(struct link_params *params, xcm_mask = REG_RD(bp, port ? NIG_REG_LLH1_XCM_MASK : NIG_REG_LLH0_XCM_MASK); - /** + /* * nig params will override non PFC params, since it's possible to * do transition from PFC to SAFC */ @@ -994,7 +963,7 @@ void bnx2x_update_pfc(struct link_params *params, struct link_vars *vars, struct bnx2x_nig_brb_pfc_port_params *pfc_params) { - /** + /* * The PFC and pause are orthogonal to one another, meaning when * PFC is enabled, the pause are disabled, and when PFC is * disabled, pause are set according to the pause result. @@ -1035,7 +1004,7 @@ void bnx2x_update_pfc(struct link_params *params, static u8 bnx2x_bmac1_enable(struct link_params *params, struct link_vars *vars, - u8 is_lb) + u8 is_lb) { struct bnx2x *bp = params->bp; u8 port = params->port; @@ -1049,9 +1018,8 @@ static u8 bnx2x_bmac1_enable(struct link_params *params, /* XGXS control */ wb_data[0] = 0x3c; wb_data[1] = 0; - REG_WR_DMAE(bp, bmac_addr + - BIGMAC_REGISTER_BMAC_XGXS_CONTROL, - wb_data, 2); + REG_WR_DMAE(bp, bmac_addr + BIGMAC_REGISTER_BMAC_XGXS_CONTROL, + wb_data, 2); /* tx MAC SA */ wb_data[0] = ((params->mac_addr[2] << 24) | @@ -1060,8 +1028,7 @@ static u8 bnx2x_bmac1_enable(struct link_params *params, params->mac_addr[5]); wb_data[1] = ((params->mac_addr[0] << 8) | params->mac_addr[1]); - REG_WR_DMAE(bp, bmac_addr + BIGMAC_REGISTER_TX_SOURCE_ADDR, - wb_data, 2); + REG_WR_DMAE(bp, bmac_addr + BIGMAC_REGISTER_TX_SOURCE_ADDR, wb_data, 2); /* mac control */ val = 0x3; @@ -1071,43 +1038,30 @@ static u8 bnx2x_bmac1_enable(struct link_params *params, } wb_data[0] = val; wb_data[1] = 0; - REG_WR_DMAE(bp, bmac_addr + BIGMAC_REGISTER_BMAC_CONTROL, - wb_data, 2); + REG_WR_DMAE(bp, bmac_addr + BIGMAC_REGISTER_BMAC_CONTROL, wb_data, 2); /* set rx mtu */ wb_data[0] = ETH_MAX_JUMBO_PACKET_SIZE + ETH_OVREHEAD; wb_data[1] = 0; - REG_WR_DMAE(bp, bmac_addr + BIGMAC_REGISTER_RX_MAX_SIZE, - wb_data, 2); + REG_WR_DMAE(bp, bmac_addr + BIGMAC_REGISTER_RX_MAX_SIZE, wb_data, 2); bnx2x_update_pfc_bmac1(params, vars); /* set tx mtu */ wb_data[0] = ETH_MAX_JUMBO_PACKET_SIZE + ETH_OVREHEAD; wb_data[1] = 0; - REG_WR_DMAE(bp, bmac_addr + BIGMAC_REGISTER_TX_MAX_SIZE, - wb_data, 2); + REG_WR_DMAE(bp, bmac_addr + BIGMAC_REGISTER_TX_MAX_SIZE, wb_data, 2); /* set cnt max size */ wb_data[0] = ETH_MAX_JUMBO_PACKET_SIZE + ETH_OVREHEAD; wb_data[1] = 0; - REG_WR_DMAE(bp, bmac_addr + BIGMAC_REGISTER_CNT_MAX_SIZE, - wb_data, 2); + REG_WR_DMAE(bp, bmac_addr + BIGMAC_REGISTER_CNT_MAX_SIZE, wb_data, 2); /* configure safc */ wb_data[0] = 0x1000200; wb_data[1] = 0; REG_WR_DMAE(bp, bmac_addr + BIGMAC_REGISTER_RX_LLFC_MSG_FLDS, wb_data, 2); - /* fix for emulation */ - if (CHIP_REV_IS_EMUL(bp)) { - wb_data[0] = 0xf000; - wb_data[1] = 0; - REG_WR_DMAE(bp, - bmac_addr + BIGMAC_REGISTER_TX_PAUSE_THRESHOLD, - wb_data, 2); - } - return 0; } @@ -1126,16 +1080,14 @@ static u8 bnx2x_bmac2_enable(struct link_params *params, wb_data[0] = 0; wb_data[1] = 0; - REG_WR_DMAE(bp, bmac_addr + BIGMAC2_REGISTER_BMAC_CONTROL, - wb_data, 2); + REG_WR_DMAE(bp, bmac_addr + BIGMAC2_REGISTER_BMAC_CONTROL, wb_data, 2); udelay(30); /* XGXS control: Reset phy HW, MDIO registers, PHY PLL and BMAC */ wb_data[0] = 0x3c; wb_data[1] = 0; - REG_WR_DMAE(bp, bmac_addr + - BIGMAC2_REGISTER_BMAC_XGXS_CONTROL, - wb_data, 2); + REG_WR_DMAE(bp, bmac_addr + BIGMAC2_REGISTER_BMAC_XGXS_CONTROL, + wb_data, 2); udelay(30); @@ -1147,7 +1099,7 @@ static u8 bnx2x_bmac2_enable(struct link_params *params, wb_data[1] = ((params->mac_addr[0] << 8) | params->mac_addr[1]); REG_WR_DMAE(bp, bmac_addr + BIGMAC2_REGISTER_TX_SOURCE_ADDR, - wb_data, 2); + wb_data, 2); udelay(30); @@ -1155,27 +1107,24 @@ static u8 bnx2x_bmac2_enable(struct link_params *params, wb_data[0] = 0x1000200; wb_data[1] = 0; REG_WR_DMAE(bp, bmac_addr + BIGMAC2_REGISTER_RX_LLFC_MSG_FLDS, - wb_data, 2); + wb_data, 2); udelay(30); /* set rx mtu */ wb_data[0] = ETH_MAX_JUMBO_PACKET_SIZE + ETH_OVREHEAD; wb_data[1] = 0; - REG_WR_DMAE(bp, bmac_addr + BIGMAC2_REGISTER_RX_MAX_SIZE, - wb_data, 2); + REG_WR_DMAE(bp, bmac_addr + BIGMAC2_REGISTER_RX_MAX_SIZE, wb_data, 2); udelay(30); /* set tx mtu */ wb_data[0] = ETH_MAX_JUMBO_PACKET_SIZE + ETH_OVREHEAD; wb_data[1] = 0; - REG_WR_DMAE(bp, bmac_addr + BIGMAC2_REGISTER_TX_MAX_SIZE, - wb_data, 2); + REG_WR_DMAE(bp, bmac_addr + BIGMAC2_REGISTER_TX_MAX_SIZE, wb_data, 2); udelay(30); /* set cnt max size */ wb_data[0] = ETH_MAX_JUMBO_PACKET_SIZE + ETH_OVREHEAD - 2; wb_data[1] = 0; - REG_WR_DMAE(bp, bmac_addr + BIGMAC2_REGISTER_CNT_MAX_SIZE, - wb_data, 2); + REG_WR_DMAE(bp, bmac_addr + BIGMAC2_REGISTER_CNT_MAX_SIZE, wb_data, 2); udelay(30); bnx2x_update_pfc_bmac2(params, vars, is_lb); @@ -1191,11 +1140,11 @@ static u8 bnx2x_bmac_enable(struct link_params *params, u32 val; /* reset and unreset the BigMac */ REG_WR(bp, GRCBASE_MISC + MISC_REGISTERS_RESET_REG_2_CLEAR, - (MISC_REGISTERS_RESET_REG_2_RST_BMAC0 << port)); + (MISC_REGISTERS_RESET_REG_2_RST_BMAC0 << port)); msleep(1); REG_WR(bp, GRCBASE_MISC + MISC_REGISTERS_RESET_REG_2_SET, - (MISC_REGISTERS_RESET_REG_2_RST_BMAC0 << port)); + (MISC_REGISTERS_RESET_REG_2_RST_BMAC0 << port)); /* enable access for bmac registers */ REG_WR(bp, NIG_REG_BMAC0_REGS_OUT_EN + port*4, 0x1); @@ -1230,15 +1179,14 @@ static void bnx2x_update_mng(struct link_params *params, u32 link_status) struct bnx2x *bp = params->bp; REG_WR(bp, params->shmem_base + - offsetof(struct shmem_region, - port_mb[params->port].link_status), - link_status); + offsetof(struct shmem_region, + port_mb[params->port].link_status), link_status); } static void bnx2x_bmac_rx_disable(struct bnx2x *bp, u8 port) { u32 bmac_addr = port ? NIG_REG_INGRESS_BMAC1_MEM : - NIG_REG_INGRESS_BMAC0_MEM; + NIG_REG_INGRESS_BMAC0_MEM; u32 wb_data[2]; u32 nig_bmac_enable = REG_RD(bp, NIG_REG_BMAC0_REGS_OUT_EN + port*4); @@ -1250,12 +1198,12 @@ static void bnx2x_bmac_rx_disable(struct bnx2x *bp, u8 port) if (CHIP_IS_E2(bp)) { /* Clear Rx Enable bit in BMAC_CONTROL register */ REG_RD_DMAE(bp, bmac_addr + - BIGMAC2_REGISTER_BMAC_CONTROL, - wb_data, 2); + BIGMAC2_REGISTER_BMAC_CONTROL, + wb_data, 2); wb_data[0] &= ~BMAC_CONTROL_RX_ENABLE; REG_WR_DMAE(bp, bmac_addr + - BIGMAC2_REGISTER_BMAC_CONTROL, - wb_data, 2); + BIGMAC2_REGISTER_BMAC_CONTROL, + wb_data, 2); } else { /* Clear Rx Enable bit in BMAC_CONTROL register */ REG_RD_DMAE(bp, bmac_addr + @@ -1271,7 +1219,7 @@ static void bnx2x_bmac_rx_disable(struct bnx2x *bp, u8 port) } static u8 bnx2x_pbf_update(struct link_params *params, u32 flow_ctrl, - u32 line_speed) + u32 line_speed) { struct bnx2x *bp = params->bp; u8 port = params->port; @@ -1308,7 +1256,7 @@ static u8 bnx2x_pbf_update(struct link_params *params, u32 flow_ctrl, /* update threshold */ REG_WR(bp, PBF_REG_P0_ARB_THRSH + port*4, 0); /* update init credit */ - init_crd = 778; /* (800-18-4) */ + init_crd = 778; /* (800-18-4) */ } else { u32 thresh = (ETH_MAX_JUMBO_PACKET_SIZE + @@ -1353,6 +1301,23 @@ static u8 bnx2x_pbf_update(struct link_params *params, u32 flow_ctrl, return 0; } +/* + * get_emac_base + * + * @param cb + * @param mdc_mdio_access + * @param port + * + * @return u32 + * + * This function selects the MDC/MDIO access (through emac0 or + * emac1) depend on the mdc_mdio_access, port, port swapped. Each + * phy has a default access mode, which could also be overridden + * by nvram configuration. This parameter, whether this is the + * default phy configuration, or the nvram overrun + * configuration, is passed here as mdc_mdio_access and selects + * the emac_base for the CL45 read/writes operations + */ static u32 bnx2x_get_emac_base(struct bnx2x *bp, u32 mdc_mdio_access, u8 port) { @@ -1385,13 +1350,16 @@ static u32 bnx2x_get_emac_base(struct bnx2x *bp, } -u8 bnx2x_cl45_write(struct bnx2x *bp, struct bnx2x_phy *phy, - u8 devad, u16 reg, u16 val) +/******************************************************************/ +/* CL45 access functions */ +/******************************************************************/ +static u8 bnx2x_cl45_write(struct bnx2x *bp, struct bnx2x_phy *phy, + u8 devad, u16 reg, u16 val) { u32 tmp, saved_mode; u8 i, rc = 0; - - /* set clause 45 mode, slow down the MDIO clock to 2.5MHz + /* + * Set clause 45 mode, slow down the MDIO clock to 2.5MHz * (a value of 49==0x31) and make sure that the AUTO poll is off */ @@ -1414,8 +1382,7 @@ u8 bnx2x_cl45_write(struct bnx2x *bp, struct bnx2x_phy *phy, for (i = 0; i < 50; i++) { udelay(10); - tmp = REG_RD(bp, phy->mdio_ctrl + - EMAC_REG_EMAC_MDIO_COMM); + tmp = REG_RD(bp, phy->mdio_ctrl + EMAC_REG_EMAC_MDIO_COMM); if (!(tmp & EMAC_MDIO_COMM_START_BUSY)) { udelay(5); break; @@ -1423,6 +1390,7 @@ u8 bnx2x_cl45_write(struct bnx2x *bp, struct bnx2x_phy *phy, } if (tmp & EMAC_MDIO_COMM_START_BUSY) { DP(NETIF_MSG_LINK, "write phy register failed\n"); + netdev_err(bp->dev, "MDC/MDIO access timeout\n"); rc = -EFAULT; } else { /* data */ @@ -1435,7 +1403,7 @@ u8 bnx2x_cl45_write(struct bnx2x *bp, struct bnx2x_phy *phy, udelay(10); tmp = REG_RD(bp, phy->mdio_ctrl + - EMAC_REG_EMAC_MDIO_COMM); + EMAC_REG_EMAC_MDIO_COMM); if (!(tmp & EMAC_MDIO_COMM_START_BUSY)) { udelay(5); break; @@ -1443,6 +1411,7 @@ u8 bnx2x_cl45_write(struct bnx2x *bp, struct bnx2x_phy *phy, } if (tmp & EMAC_MDIO_COMM_START_BUSY) { DP(NETIF_MSG_LINK, "write phy register failed\n"); + netdev_err(bp->dev, "MDC/MDIO access timeout\n"); rc = -EFAULT; } } @@ -1453,20 +1422,20 @@ u8 bnx2x_cl45_write(struct bnx2x *bp, struct bnx2x_phy *phy, return rc; } -u8 bnx2x_cl45_read(struct bnx2x *bp, struct bnx2x_phy *phy, - u8 devad, u16 reg, u16 *ret_val) +static u8 bnx2x_cl45_read(struct bnx2x *bp, struct bnx2x_phy *phy, + u8 devad, u16 reg, u16 *ret_val) { u32 val, saved_mode; u16 i; u8 rc = 0; - - /* set clause 45 mode, slow down the MDIO clock to 2.5MHz + /* + * Set clause 45 mode, slow down the MDIO clock to 2.5MHz * (a value of 49==0x31) and make sure that the AUTO poll is off */ saved_mode = REG_RD(bp, phy->mdio_ctrl + EMAC_REG_EMAC_MDIO_MODE); val = saved_mode & ~((EMAC_MDIO_MODE_AUTO_POLL | - EMAC_MDIO_MODE_CLOCK_CNT)); + EMAC_MDIO_MODE_CLOCK_CNT)); val |= (EMAC_MDIO_MODE_CLAUSE_45 | (49L << EMAC_MDIO_MODE_CLOCK_CNT_BITSHIFT)); REG_WR(bp, phy->mdio_ctrl + EMAC_REG_EMAC_MDIO_MODE, val); @@ -1490,7 +1459,7 @@ u8 bnx2x_cl45_read(struct bnx2x *bp, struct bnx2x_phy *phy, } if (val & EMAC_MDIO_COMM_START_BUSY) { DP(NETIF_MSG_LINK, "read phy register failed\n"); - + netdev_err(bp->dev, "MDC/MDIO access timeout\n"); *ret_val = 0; rc = -EFAULT; @@ -1505,7 +1474,7 @@ u8 bnx2x_cl45_read(struct bnx2x *bp, struct bnx2x_phy *phy, udelay(10); val = REG_RD(bp, phy->mdio_ctrl + - EMAC_REG_EMAC_MDIO_COMM); + EMAC_REG_EMAC_MDIO_COMM); if (!(val & EMAC_MDIO_COMM_START_BUSY)) { *ret_val = (u16)(val & EMAC_MDIO_COMM_DATA); break; @@ -1513,7 +1482,7 @@ u8 bnx2x_cl45_read(struct bnx2x *bp, struct bnx2x_phy *phy, } if (val & EMAC_MDIO_COMM_START_BUSY) { DP(NETIF_MSG_LINK, "read phy register failed\n"); - + netdev_err(bp->dev, "MDC/MDIO access timeout\n"); *ret_val = 0; rc = -EFAULT; } @@ -1529,7 +1498,7 @@ u8 bnx2x_phy_read(struct link_params *params, u8 phy_addr, u8 devad, u16 reg, u16 *ret_val) { u8 phy_index; - /** + /* * Probe for the phy according to the given phy_addr, and execute * the read request on it */ @@ -1547,7 +1516,7 @@ u8 bnx2x_phy_write(struct link_params *params, u8 phy_addr, u8 devad, u16 reg, u16 val) { u8 phy_index; - /** + /* * Probe for the phy according to the given phy_addr, and execute * the write request on it */ @@ -1576,16 +1545,15 @@ static void bnx2x_set_aer_mmd_xgxs(struct link_params *params, aer_val = 0x3800 + offset - 1; else aer_val = 0x3800 + offset; - CL45_WR_OVER_CL22(bp, phy, - MDIO_REG_BANK_AER_BLOCK, - MDIO_AER_BLOCK_AER_REG, aer_val); + CL22_WR_OVER_CL45(bp, phy, MDIO_REG_BANK_AER_BLOCK, + MDIO_AER_BLOCK_AER_REG, aer_val); } static void bnx2x_set_aer_mmd_serdes(struct bnx2x *bp, struct bnx2x_phy *phy) { - CL45_WR_OVER_CL22(bp, phy, - MDIO_REG_BANK_AER_BLOCK, - MDIO_AER_BLOCK_AER_REG, 0x3800); + CL22_WR_OVER_CL45(bp, phy, + MDIO_REG_BANK_AER_BLOCK, + MDIO_AER_BLOCK_AER_REG, 0x3800); } /******************************************************************/ @@ -1621,9 +1589,8 @@ static void bnx2x_serdes_deassert(struct bnx2x *bp, u8 port) bnx2x_set_serdes_access(bp, port); - REG_WR(bp, NIG_REG_SERDES0_CTRL_MD_DEVAD + - port*0x10, - DEFAULT_PHY_DEV_ADDR); + REG_WR(bp, NIG_REG_SERDES0_CTRL_MD_DEVAD + port*0x10, + DEFAULT_PHY_DEV_ADDR); } static void bnx2x_xgxs_deassert(struct link_params *params) @@ -1641,23 +1608,22 @@ static void bnx2x_xgxs_deassert(struct link_params *params) udelay(500); REG_WR(bp, GRCBASE_MISC + MISC_REGISTERS_RESET_REG_3_SET, val); - REG_WR(bp, NIG_REG_XGXS0_CTRL_MD_ST + - port*0x18, 0); + REG_WR(bp, NIG_REG_XGXS0_CTRL_MD_ST + port*0x18, 0); REG_WR(bp, NIG_REG_XGXS0_CTRL_MD_DEVAD + port*0x18, - params->phy[INT_PHY].def_md_devad); + params->phy[INT_PHY].def_md_devad); } void bnx2x_link_status_update(struct link_params *params, - struct link_vars *vars) + struct link_vars *vars) { struct bnx2x *bp = params->bp; u8 link_10g; u8 port = params->port; vars->link_status = REG_RD(bp, params->shmem_base + - offsetof(struct shmem_region, - port_mb[port].link_status)); + offsetof(struct shmem_region, + port_mb[port].link_status)); vars->link_up = (vars->link_status & LINK_STATUS_LINK_UP); @@ -1667,7 +1633,7 @@ void bnx2x_link_status_update(struct link_params *params, vars->phy_link_up = 1; vars->duplex = DUPLEX_FULL; switch (vars->link_status & - LINK_STATUS_SPEED_AND_DUPLEX_MASK) { + LINK_STATUS_SPEED_AND_DUPLEX_MASK) { case LINK_10THD: vars->duplex = DUPLEX_HALF; /* fall thru */ @@ -1779,20 +1745,20 @@ static void bnx2x_set_master_ln(struct link_params *params, { struct bnx2x *bp = params->bp; u16 new_master_ln, ser_lane; - ser_lane = ((params->lane_config & + ser_lane = ((params->lane_config & PORT_HW_CFG_LANE_SWAP_CFG_MASTER_MASK) >> - PORT_HW_CFG_LANE_SWAP_CFG_MASTER_SHIFT); + PORT_HW_CFG_LANE_SWAP_CFG_MASTER_SHIFT); /* set the master_ln for AN */ - CL45_RD_OVER_CL22(bp, phy, - MDIO_REG_BANK_XGXS_BLOCK2, - MDIO_XGXS_BLOCK2_TEST_MODE_LANE, - &new_master_ln); + CL22_RD_OVER_CL45(bp, phy, + MDIO_REG_BANK_XGXS_BLOCK2, + MDIO_XGXS_BLOCK2_TEST_MODE_LANE, + &new_master_ln); - CL45_WR_OVER_CL22(bp, phy, - MDIO_REG_BANK_XGXS_BLOCK2 , - MDIO_XGXS_BLOCK2_TEST_MODE_LANE, - (new_master_ln | ser_lane)); + CL22_WR_OVER_CL45(bp, phy, + MDIO_REG_BANK_XGXS_BLOCK2 , + MDIO_XGXS_BLOCK2_TEST_MODE_LANE, + (new_master_ln | ser_lane)); } static u8 bnx2x_reset_unicore(struct link_params *params, @@ -1802,17 +1768,16 @@ static u8 bnx2x_reset_unicore(struct link_params *params, struct bnx2x *bp = params->bp; u16 mii_control; u16 i; - - CL45_RD_OVER_CL22(bp, phy, - MDIO_REG_BANK_COMBO_IEEE0, - MDIO_COMBO_IEEE0_MII_CONTROL, &mii_control); + CL22_RD_OVER_CL45(bp, phy, + MDIO_REG_BANK_COMBO_IEEE0, + MDIO_COMBO_IEEE0_MII_CONTROL, &mii_control); /* reset the unicore */ - CL45_WR_OVER_CL22(bp, phy, - MDIO_REG_BANK_COMBO_IEEE0, - MDIO_COMBO_IEEE0_MII_CONTROL, - (mii_control | - MDIO_COMBO_IEEO_MII_CONTROL_RESET)); + CL22_WR_OVER_CL45(bp, phy, + MDIO_REG_BANK_COMBO_IEEE0, + MDIO_COMBO_IEEE0_MII_CONTROL, + (mii_control | + MDIO_COMBO_IEEO_MII_CONTROL_RESET)); if (set_serdes) bnx2x_set_serdes_access(bp, params->port); @@ -1821,10 +1786,10 @@ static u8 bnx2x_reset_unicore(struct link_params *params, udelay(5); /* the reset erased the previous bank value */ - CL45_RD_OVER_CL22(bp, phy, - MDIO_REG_BANK_COMBO_IEEE0, - MDIO_COMBO_IEEE0_MII_CONTROL, - &mii_control); + CL22_RD_OVER_CL45(bp, phy, + MDIO_REG_BANK_COMBO_IEEE0, + MDIO_COMBO_IEEE0_MII_CONTROL, + &mii_control); if (!(mii_control & MDIO_COMBO_IEEO_MII_CONTROL_RESET)) { udelay(5); @@ -1832,6 +1797,9 @@ static u8 bnx2x_reset_unicore(struct link_params *params, } } + netdev_err(bp->dev, "Warning: PHY was not initialized," + " Port %d\n", + params->port); DP(NETIF_MSG_LINK, "BUG! XGXS is still in reset!\n"); return -EINVAL; @@ -1841,43 +1809,45 @@ static void bnx2x_set_swap_lanes(struct link_params *params, struct bnx2x_phy *phy) { struct bnx2x *bp = params->bp; - /* Each two bits represents a lane number: - No swap is 0123 => 0x1b no need to enable the swap */ + /* + * Each two bits represents a lane number: + * No swap is 0123 => 0x1b no need to enable the swap + */ u16 ser_lane, rx_lane_swap, tx_lane_swap; ser_lane = ((params->lane_config & - PORT_HW_CFG_LANE_SWAP_CFG_MASTER_MASK) >> - PORT_HW_CFG_LANE_SWAP_CFG_MASTER_SHIFT); + PORT_HW_CFG_LANE_SWAP_CFG_MASTER_MASK) >> + PORT_HW_CFG_LANE_SWAP_CFG_MASTER_SHIFT); rx_lane_swap = ((params->lane_config & - PORT_HW_CFG_LANE_SWAP_CFG_RX_MASK) >> - PORT_HW_CFG_LANE_SWAP_CFG_RX_SHIFT); + PORT_HW_CFG_LANE_SWAP_CFG_RX_MASK) >> + PORT_HW_CFG_LANE_SWAP_CFG_RX_SHIFT); tx_lane_swap = ((params->lane_config & - PORT_HW_CFG_LANE_SWAP_CFG_TX_MASK) >> - PORT_HW_CFG_LANE_SWAP_CFG_TX_SHIFT); + PORT_HW_CFG_LANE_SWAP_CFG_TX_MASK) >> + PORT_HW_CFG_LANE_SWAP_CFG_TX_SHIFT); if (rx_lane_swap != 0x1b) { - CL45_WR_OVER_CL22(bp, phy, - MDIO_REG_BANK_XGXS_BLOCK2, - MDIO_XGXS_BLOCK2_RX_LN_SWAP, - (rx_lane_swap | - MDIO_XGXS_BLOCK2_RX_LN_SWAP_ENABLE | - MDIO_XGXS_BLOCK2_RX_LN_SWAP_FORCE_ENABLE)); + CL22_WR_OVER_CL45(bp, phy, + MDIO_REG_BANK_XGXS_BLOCK2, + MDIO_XGXS_BLOCK2_RX_LN_SWAP, + (rx_lane_swap | + MDIO_XGXS_BLOCK2_RX_LN_SWAP_ENABLE | + MDIO_XGXS_BLOCK2_RX_LN_SWAP_FORCE_ENABLE)); } else { - CL45_WR_OVER_CL22(bp, phy, - MDIO_REG_BANK_XGXS_BLOCK2, - MDIO_XGXS_BLOCK2_RX_LN_SWAP, 0); + CL22_WR_OVER_CL45(bp, phy, + MDIO_REG_BANK_XGXS_BLOCK2, + MDIO_XGXS_BLOCK2_RX_LN_SWAP, 0); } if (tx_lane_swap != 0x1b) { - CL45_WR_OVER_CL22(bp, phy, - MDIO_REG_BANK_XGXS_BLOCK2, - MDIO_XGXS_BLOCK2_TX_LN_SWAP, - (tx_lane_swap | - MDIO_XGXS_BLOCK2_TX_LN_SWAP_ENABLE)); + CL22_WR_OVER_CL45(bp, phy, + MDIO_REG_BANK_XGXS_BLOCK2, + MDIO_XGXS_BLOCK2_TX_LN_SWAP, + (tx_lane_swap | + MDIO_XGXS_BLOCK2_TX_LN_SWAP_ENABLE)); } else { - CL45_WR_OVER_CL22(bp, phy, - MDIO_REG_BANK_XGXS_BLOCK2, - MDIO_XGXS_BLOCK2_TX_LN_SWAP, 0); + CL22_WR_OVER_CL45(bp, phy, + MDIO_REG_BANK_XGXS_BLOCK2, + MDIO_XGXS_BLOCK2_TX_LN_SWAP, 0); } } @@ -1886,66 +1856,66 @@ static void bnx2x_set_parallel_detection(struct bnx2x_phy *phy, { struct bnx2x *bp = params->bp; u16 control2; - CL45_RD_OVER_CL22(bp, phy, - MDIO_REG_BANK_SERDES_DIGITAL, - MDIO_SERDES_DIGITAL_A_1000X_CONTROL2, - &control2); + CL22_RD_OVER_CL45(bp, phy, + MDIO_REG_BANK_SERDES_DIGITAL, + MDIO_SERDES_DIGITAL_A_1000X_CONTROL2, + &control2); if (phy->speed_cap_mask & PORT_HW_CFG_SPEED_CAPABILITY_D0_1G) control2 |= MDIO_SERDES_DIGITAL_A_1000X_CONTROL2_PRL_DT_EN; else control2 &= ~MDIO_SERDES_DIGITAL_A_1000X_CONTROL2_PRL_DT_EN; DP(NETIF_MSG_LINK, "phy->speed_cap_mask = 0x%x, control2 = 0x%x\n", phy->speed_cap_mask, control2); - CL45_WR_OVER_CL22(bp, phy, - MDIO_REG_BANK_SERDES_DIGITAL, - MDIO_SERDES_DIGITAL_A_1000X_CONTROL2, - control2); + CL22_WR_OVER_CL45(bp, phy, + MDIO_REG_BANK_SERDES_DIGITAL, + MDIO_SERDES_DIGITAL_A_1000X_CONTROL2, + control2); if ((phy->type == PORT_HW_CFG_XGXS_EXT_PHY_TYPE_DIRECT) && (phy->speed_cap_mask & PORT_HW_CFG_SPEED_CAPABILITY_D0_10G)) { DP(NETIF_MSG_LINK, "XGXS\n"); - CL45_WR_OVER_CL22(bp, phy, - MDIO_REG_BANK_10G_PARALLEL_DETECT, - MDIO_10G_PARALLEL_DETECT_PAR_DET_10G_LINK, - MDIO_10G_PARALLEL_DETECT_PAR_DET_10G_LINK_CNT); + CL22_WR_OVER_CL45(bp, phy, + MDIO_REG_BANK_10G_PARALLEL_DETECT, + MDIO_10G_PARALLEL_DETECT_PAR_DET_10G_LINK, + MDIO_10G_PARALLEL_DETECT_PAR_DET_10G_LINK_CNT); - CL45_RD_OVER_CL22(bp, phy, - MDIO_REG_BANK_10G_PARALLEL_DETECT, - MDIO_10G_PARALLEL_DETECT_PAR_DET_10G_CONTROL, - &control2); + CL22_RD_OVER_CL45(bp, phy, + MDIO_REG_BANK_10G_PARALLEL_DETECT, + MDIO_10G_PARALLEL_DETECT_PAR_DET_10G_CONTROL, + &control2); control2 |= MDIO_10G_PARALLEL_DETECT_PAR_DET_10G_CONTROL_PARDET10G_EN; - CL45_WR_OVER_CL22(bp, phy, - MDIO_REG_BANK_10G_PARALLEL_DETECT, - MDIO_10G_PARALLEL_DETECT_PAR_DET_10G_CONTROL, - control2); + CL22_WR_OVER_CL45(bp, phy, + MDIO_REG_BANK_10G_PARALLEL_DETECT, + MDIO_10G_PARALLEL_DETECT_PAR_DET_10G_CONTROL, + control2); /* Disable parallel detection of HiG */ - CL45_WR_OVER_CL22(bp, phy, - MDIO_REG_BANK_XGXS_BLOCK2, - MDIO_XGXS_BLOCK2_UNICORE_MODE_10G, - MDIO_XGXS_BLOCK2_UNICORE_MODE_10G_CX4_XGXS | - MDIO_XGXS_BLOCK2_UNICORE_MODE_10G_HIGIG_XGXS); + CL22_WR_OVER_CL45(bp, phy, + MDIO_REG_BANK_XGXS_BLOCK2, + MDIO_XGXS_BLOCK2_UNICORE_MODE_10G, + MDIO_XGXS_BLOCK2_UNICORE_MODE_10G_CX4_XGXS | + MDIO_XGXS_BLOCK2_UNICORE_MODE_10G_HIGIG_XGXS); } } static void bnx2x_set_autoneg(struct bnx2x_phy *phy, struct link_params *params, - struct link_vars *vars, - u8 enable_cl73) + struct link_vars *vars, + u8 enable_cl73) { struct bnx2x *bp = params->bp; u16 reg_val; /* CL37 Autoneg */ - CL45_RD_OVER_CL22(bp, phy, - MDIO_REG_BANK_COMBO_IEEE0, - MDIO_COMBO_IEEE0_MII_CONTROL, ®_val); + CL22_RD_OVER_CL45(bp, phy, + MDIO_REG_BANK_COMBO_IEEE0, + MDIO_COMBO_IEEE0_MII_CONTROL, ®_val); /* CL37 Autoneg Enabled */ if (vars->line_speed == SPEED_AUTO_NEG) @@ -1954,15 +1924,15 @@ static void bnx2x_set_autoneg(struct bnx2x_phy *phy, reg_val &= ~(MDIO_COMBO_IEEO_MII_CONTROL_AN_EN | MDIO_COMBO_IEEO_MII_CONTROL_RESTART_AN); - CL45_WR_OVER_CL22(bp, phy, - MDIO_REG_BANK_COMBO_IEEE0, - MDIO_COMBO_IEEE0_MII_CONTROL, reg_val); + CL22_WR_OVER_CL45(bp, phy, + MDIO_REG_BANK_COMBO_IEEE0, + MDIO_COMBO_IEEE0_MII_CONTROL, reg_val); /* Enable/Disable Autodetection */ - CL45_RD_OVER_CL22(bp, phy, - MDIO_REG_BANK_SERDES_DIGITAL, - MDIO_SERDES_DIGITAL_A_1000X_CONTROL1, ®_val); + CL22_RD_OVER_CL45(bp, phy, + MDIO_REG_BANK_SERDES_DIGITAL, + MDIO_SERDES_DIGITAL_A_1000X_CONTROL1, ®_val); reg_val &= ~(MDIO_SERDES_DIGITAL_A_1000X_CONTROL1_SIGNAL_DETECT_EN | MDIO_SERDES_DIGITAL_A_1000X_CONTROL1_INVERT_SIGNAL_DETECT); reg_val |= MDIO_SERDES_DIGITAL_A_1000X_CONTROL1_FIBER_MODE; @@ -1971,14 +1941,14 @@ static void bnx2x_set_autoneg(struct bnx2x_phy *phy, else reg_val &= ~MDIO_SERDES_DIGITAL_A_1000X_CONTROL1_AUTODET; - CL45_WR_OVER_CL22(bp, phy, - MDIO_REG_BANK_SERDES_DIGITAL, - MDIO_SERDES_DIGITAL_A_1000X_CONTROL1, reg_val); + CL22_WR_OVER_CL45(bp, phy, + MDIO_REG_BANK_SERDES_DIGITAL, + MDIO_SERDES_DIGITAL_A_1000X_CONTROL1, reg_val); /* Enable TetonII and BAM autoneg */ - CL45_RD_OVER_CL22(bp, phy, - MDIO_REG_BANK_BAM_NEXT_PAGE, - MDIO_BAM_NEXT_PAGE_MP5_NEXT_PAGE_CTRL, + CL22_RD_OVER_CL45(bp, phy, + MDIO_REG_BANK_BAM_NEXT_PAGE, + MDIO_BAM_NEXT_PAGE_MP5_NEXT_PAGE_CTRL, ®_val); if (vars->line_speed == SPEED_AUTO_NEG) { /* Enable BAM aneg Mode and TetonII aneg Mode */ @@ -1989,20 +1959,20 @@ static void bnx2x_set_autoneg(struct bnx2x_phy *phy, reg_val &= ~(MDIO_BAM_NEXT_PAGE_MP5_NEXT_PAGE_CTRL_BAM_MODE | MDIO_BAM_NEXT_PAGE_MP5_NEXT_PAGE_CTRL_TETON_AN); } - CL45_WR_OVER_CL22(bp, phy, - MDIO_REG_BANK_BAM_NEXT_PAGE, - MDIO_BAM_NEXT_PAGE_MP5_NEXT_PAGE_CTRL, - reg_val); + CL22_WR_OVER_CL45(bp, phy, + MDIO_REG_BANK_BAM_NEXT_PAGE, + MDIO_BAM_NEXT_PAGE_MP5_NEXT_PAGE_CTRL, + reg_val); if (enable_cl73) { /* Enable Cl73 FSM status bits */ - CL45_WR_OVER_CL22(bp, phy, - MDIO_REG_BANK_CL73_USERB0, - MDIO_CL73_USERB0_CL73_UCTRL, - 0xe); + CL22_WR_OVER_CL45(bp, phy, + MDIO_REG_BANK_CL73_USERB0, + MDIO_CL73_USERB0_CL73_UCTRL, + 0xe); /* Enable BAM Station Manager*/ - CL45_WR_OVER_CL22(bp, phy, + CL22_WR_OVER_CL45(bp, phy, MDIO_REG_BANK_CL73_USERB0, MDIO_CL73_USERB0_CL73_BAM_CTRL1, MDIO_CL73_USERB0_CL73_BAM_CTRL1_BAM_EN | @@ -2010,10 +1980,10 @@ static void bnx2x_set_autoneg(struct bnx2x_phy *phy, MDIO_CL73_USERB0_CL73_BAM_CTRL1_BAM_NP_AFTER_BP_EN); /* Advertise CL73 link speeds */ - CL45_RD_OVER_CL22(bp, phy, - MDIO_REG_BANK_CL73_IEEEB1, - MDIO_CL73_IEEEB1_AN_ADV2, - ®_val); + CL22_RD_OVER_CL45(bp, phy, + MDIO_REG_BANK_CL73_IEEEB1, + MDIO_CL73_IEEEB1_AN_ADV2, + ®_val); if (phy->speed_cap_mask & PORT_HW_CFG_SPEED_CAPABILITY_D0_10G) reg_val |= MDIO_CL73_IEEEB1_AN_ADV2_ADVR_10G_KX4; @@ -2021,10 +1991,10 @@ static void bnx2x_set_autoneg(struct bnx2x_phy *phy, PORT_HW_CFG_SPEED_CAPABILITY_D0_1G) reg_val |= MDIO_CL73_IEEEB1_AN_ADV2_ADVR_1000M_KX; - CL45_WR_OVER_CL22(bp, phy, - MDIO_REG_BANK_CL73_IEEEB1, - MDIO_CL73_IEEEB1_AN_ADV2, - reg_val); + CL22_WR_OVER_CL45(bp, phy, + MDIO_REG_BANK_CL73_IEEEB1, + MDIO_CL73_IEEEB1_AN_ADV2, + reg_val); /* CL73 Autoneg Enabled */ reg_val = MDIO_CL73_IEEEB0_CL73_AN_CONTROL_AN_EN; @@ -2032,37 +2002,39 @@ static void bnx2x_set_autoneg(struct bnx2x_phy *phy, } else /* CL73 Autoneg Disabled */ reg_val = 0; - CL45_WR_OVER_CL22(bp, phy, - MDIO_REG_BANK_CL73_IEEEB0, - MDIO_CL73_IEEEB0_CL73_AN_CONTROL, reg_val); + CL22_WR_OVER_CL45(bp, phy, + MDIO_REG_BANK_CL73_IEEEB0, + MDIO_CL73_IEEEB0_CL73_AN_CONTROL, reg_val); } /* program SerDes, forced speed */ static void bnx2x_program_serdes(struct bnx2x_phy *phy, struct link_params *params, - struct link_vars *vars) + struct link_vars *vars) { struct bnx2x *bp = params->bp; u16 reg_val; /* program duplex, disable autoneg and sgmii*/ - CL45_RD_OVER_CL22(bp, phy, - MDIO_REG_BANK_COMBO_IEEE0, - MDIO_COMBO_IEEE0_MII_CONTROL, ®_val); + CL22_RD_OVER_CL45(bp, phy, + MDIO_REG_BANK_COMBO_IEEE0, + MDIO_COMBO_IEEE0_MII_CONTROL, ®_val); reg_val &= ~(MDIO_COMBO_IEEO_MII_CONTROL_FULL_DUPLEX | MDIO_COMBO_IEEO_MII_CONTROL_AN_EN | MDIO_COMBO_IEEO_MII_CONTROL_MAN_SGMII_SP_MASK); if (phy->req_duplex == DUPLEX_FULL) reg_val |= MDIO_COMBO_IEEO_MII_CONTROL_FULL_DUPLEX; - CL45_WR_OVER_CL22(bp, phy, - MDIO_REG_BANK_COMBO_IEEE0, - MDIO_COMBO_IEEE0_MII_CONTROL, reg_val); - - /* program speed - - needed only if the speed is greater than 1G (2.5G or 10G) */ - CL45_RD_OVER_CL22(bp, phy, - MDIO_REG_BANK_SERDES_DIGITAL, - MDIO_SERDES_DIGITAL_MISC1, ®_val); + CL22_WR_OVER_CL45(bp, phy, + MDIO_REG_BANK_COMBO_IEEE0, + MDIO_COMBO_IEEE0_MII_CONTROL, reg_val); + + /* + * program speed + * - needed only if the speed is greater than 1G (2.5G or 10G) + */ + CL22_RD_OVER_CL45(bp, phy, + MDIO_REG_BANK_SERDES_DIGITAL, + MDIO_SERDES_DIGITAL_MISC1, ®_val); /* clearing the speed value before setting the right speed */ DP(NETIF_MSG_LINK, "MDIO_REG_BANK_SERDES_DIGITAL = 0x%x\n", reg_val); @@ -2083,9 +2055,9 @@ static void bnx2x_program_serdes(struct bnx2x_phy *phy, MDIO_SERDES_DIGITAL_MISC1_FORCE_SPEED_13G; } - CL45_WR_OVER_CL22(bp, phy, - MDIO_REG_BANK_SERDES_DIGITAL, - MDIO_SERDES_DIGITAL_MISC1, reg_val); + CL22_WR_OVER_CL45(bp, phy, + MDIO_REG_BANK_SERDES_DIGITAL, + MDIO_SERDES_DIGITAL_MISC1, reg_val); } @@ -2102,13 +2074,13 @@ static void bnx2x_set_brcm_cl37_advertisment(struct bnx2x_phy *phy, val |= MDIO_OVER_1G_UP1_2_5G; if (phy->speed_cap_mask & PORT_HW_CFG_SPEED_CAPABILITY_D0_10G) val |= MDIO_OVER_1G_UP1_10G; - CL45_WR_OVER_CL22(bp, phy, - MDIO_REG_BANK_OVER_1G, - MDIO_OVER_1G_UP1, val); + CL22_WR_OVER_CL45(bp, phy, + MDIO_REG_BANK_OVER_1G, + MDIO_OVER_1G_UP1, val); - CL45_WR_OVER_CL22(bp, phy, - MDIO_REG_BANK_OVER_1G, - MDIO_OVER_1G_UP3, 0x400); + CL22_WR_OVER_CL45(bp, phy, + MDIO_REG_BANK_OVER_1G, + MDIO_OVER_1G_UP3, 0x400); } static void bnx2x_calc_ieee_aneg_adv(struct bnx2x_phy *phy, @@ -2116,22 +2088,21 @@ static void bnx2x_calc_ieee_aneg_adv(struct bnx2x_phy *phy, { struct bnx2x *bp = params->bp; *ieee_fc = MDIO_COMBO_IEEE0_AUTO_NEG_ADV_FULL_DUPLEX; - /* resolve pause mode and advertisement - * Please refer to Table 28B-3 of the 802.3ab-1999 spec */ + /* + * Resolve pause mode and advertisement. + * Please refer to Table 28B-3 of the 802.3ab-1999 spec + */ switch (phy->req_flow_ctrl) { case BNX2X_FLOW_CTRL_AUTO: - if (params->req_fc_auto_adv == BNX2X_FLOW_CTRL_BOTH) { - *ieee_fc |= - MDIO_COMBO_IEEE0_AUTO_NEG_ADV_PAUSE_BOTH; - } else { + if (params->req_fc_auto_adv == BNX2X_FLOW_CTRL_BOTH) + *ieee_fc |= MDIO_COMBO_IEEE0_AUTO_NEG_ADV_PAUSE_BOTH; + else *ieee_fc |= - MDIO_COMBO_IEEE0_AUTO_NEG_ADV_PAUSE_ASYMMETRIC; - } + MDIO_COMBO_IEEE0_AUTO_NEG_ADV_PAUSE_ASYMMETRIC; break; case BNX2X_FLOW_CTRL_TX: - *ieee_fc |= - MDIO_COMBO_IEEE0_AUTO_NEG_ADV_PAUSE_ASYMMETRIC; + *ieee_fc |= MDIO_COMBO_IEEE0_AUTO_NEG_ADV_PAUSE_ASYMMETRIC; break; case BNX2X_FLOW_CTRL_RX: @@ -2149,23 +2120,23 @@ static void bnx2x_calc_ieee_aneg_adv(struct bnx2x_phy *phy, static void bnx2x_set_ieee_aneg_advertisment(struct bnx2x_phy *phy, struct link_params *params, - u16 ieee_fc) + u16 ieee_fc) { struct bnx2x *bp = params->bp; u16 val; /* for AN, we are always publishing full duplex */ - CL45_WR_OVER_CL22(bp, phy, - MDIO_REG_BANK_COMBO_IEEE0, - MDIO_COMBO_IEEE0_AUTO_NEG_ADV, ieee_fc); - CL45_RD_OVER_CL22(bp, phy, - MDIO_REG_BANK_CL73_IEEEB1, - MDIO_CL73_IEEEB1_AN_ADV1, &val); + CL22_WR_OVER_CL45(bp, phy, + MDIO_REG_BANK_COMBO_IEEE0, + MDIO_COMBO_IEEE0_AUTO_NEG_ADV, ieee_fc); + CL22_RD_OVER_CL45(bp, phy, + MDIO_REG_BANK_CL73_IEEEB1, + MDIO_CL73_IEEEB1_AN_ADV1, &val); val &= ~MDIO_CL73_IEEEB1_AN_ADV1_PAUSE_BOTH; val |= ((ieee_fc<<3) & MDIO_CL73_IEEEB1_AN_ADV1_PAUSE_MASK); - CL45_WR_OVER_CL22(bp, phy, - MDIO_REG_BANK_CL73_IEEEB1, - MDIO_CL73_IEEEB1_AN_ADV1, val); + CL22_WR_OVER_CL45(bp, phy, + MDIO_REG_BANK_CL73_IEEEB1, + MDIO_CL73_IEEEB1_AN_ADV1, val); } static void bnx2x_restart_autoneg(struct bnx2x_phy *phy, @@ -2179,67 +2150,67 @@ static void bnx2x_restart_autoneg(struct bnx2x_phy *phy, /* Enable and restart BAM/CL37 aneg */ if (enable_cl73) { - CL45_RD_OVER_CL22(bp, phy, - MDIO_REG_BANK_CL73_IEEEB0, - MDIO_CL73_IEEEB0_CL73_AN_CONTROL, - &mii_control); - - CL45_WR_OVER_CL22(bp, phy, - MDIO_REG_BANK_CL73_IEEEB0, - MDIO_CL73_IEEEB0_CL73_AN_CONTROL, - (mii_control | - MDIO_CL73_IEEEB0_CL73_AN_CONTROL_AN_EN | - MDIO_CL73_IEEEB0_CL73_AN_CONTROL_RESTART_AN)); + CL22_RD_OVER_CL45(bp, phy, + MDIO_REG_BANK_CL73_IEEEB0, + MDIO_CL73_IEEEB0_CL73_AN_CONTROL, + &mii_control); + + CL22_WR_OVER_CL45(bp, phy, + MDIO_REG_BANK_CL73_IEEEB0, + MDIO_CL73_IEEEB0_CL73_AN_CONTROL, + (mii_control | + MDIO_CL73_IEEEB0_CL73_AN_CONTROL_AN_EN | + MDIO_CL73_IEEEB0_CL73_AN_CONTROL_RESTART_AN)); } else { - CL45_RD_OVER_CL22(bp, phy, - MDIO_REG_BANK_COMBO_IEEE0, - MDIO_COMBO_IEEE0_MII_CONTROL, - &mii_control); + CL22_RD_OVER_CL45(bp, phy, + MDIO_REG_BANK_COMBO_IEEE0, + MDIO_COMBO_IEEE0_MII_CONTROL, + &mii_control); DP(NETIF_MSG_LINK, "bnx2x_restart_autoneg mii_control before = 0x%x\n", mii_control); - CL45_WR_OVER_CL22(bp, phy, - MDIO_REG_BANK_COMBO_IEEE0, - MDIO_COMBO_IEEE0_MII_CONTROL, - (mii_control | - MDIO_COMBO_IEEO_MII_CONTROL_AN_EN | - MDIO_COMBO_IEEO_MII_CONTROL_RESTART_AN)); + CL22_WR_OVER_CL45(bp, phy, + MDIO_REG_BANK_COMBO_IEEE0, + MDIO_COMBO_IEEE0_MII_CONTROL, + (mii_control | + MDIO_COMBO_IEEO_MII_CONTROL_AN_EN | + MDIO_COMBO_IEEO_MII_CONTROL_RESTART_AN)); } } static void bnx2x_initialize_sgmii_process(struct bnx2x_phy *phy, struct link_params *params, - struct link_vars *vars) + struct link_vars *vars) { struct bnx2x *bp = params->bp; u16 control1; /* in SGMII mode, the unicore is always slave */ - CL45_RD_OVER_CL22(bp, phy, - MDIO_REG_BANK_SERDES_DIGITAL, - MDIO_SERDES_DIGITAL_A_1000X_CONTROL1, - &control1); + CL22_RD_OVER_CL45(bp, phy, + MDIO_REG_BANK_SERDES_DIGITAL, + MDIO_SERDES_DIGITAL_A_1000X_CONTROL1, + &control1); control1 |= MDIO_SERDES_DIGITAL_A_1000X_CONTROL1_INVERT_SIGNAL_DETECT; /* set sgmii mode (and not fiber) */ control1 &= ~(MDIO_SERDES_DIGITAL_A_1000X_CONTROL1_FIBER_MODE | MDIO_SERDES_DIGITAL_A_1000X_CONTROL1_AUTODET | MDIO_SERDES_DIGITAL_A_1000X_CONTROL1_MSTR_MODE); - CL45_WR_OVER_CL22(bp, phy, - MDIO_REG_BANK_SERDES_DIGITAL, - MDIO_SERDES_DIGITAL_A_1000X_CONTROL1, - control1); + CL22_WR_OVER_CL45(bp, phy, + MDIO_REG_BANK_SERDES_DIGITAL, + MDIO_SERDES_DIGITAL_A_1000X_CONTROL1, + control1); /* if forced speed */ if (!(vars->line_speed == SPEED_AUTO_NEG)) { /* set speed, disable autoneg */ u16 mii_control; - CL45_RD_OVER_CL22(bp, phy, - MDIO_REG_BANK_COMBO_IEEE0, - MDIO_COMBO_IEEE0_MII_CONTROL, - &mii_control); + CL22_RD_OVER_CL45(bp, phy, + MDIO_REG_BANK_COMBO_IEEE0, + MDIO_COMBO_IEEE0_MII_CONTROL, + &mii_control); mii_control &= ~(MDIO_COMBO_IEEO_MII_CONTROL_AN_EN | MDIO_COMBO_IEEO_MII_CONTROL_MAN_SGMII_SP_MASK| MDIO_COMBO_IEEO_MII_CONTROL_FULL_DUPLEX); @@ -2267,10 +2238,10 @@ static void bnx2x_initialize_sgmii_process(struct bnx2x_phy *phy, if (phy->req_duplex == DUPLEX_FULL) mii_control |= MDIO_COMBO_IEEO_MII_CONTROL_FULL_DUPLEX; - CL45_WR_OVER_CL22(bp, phy, - MDIO_REG_BANK_COMBO_IEEE0, - MDIO_COMBO_IEEE0_MII_CONTROL, - mii_control); + CL22_WR_OVER_CL45(bp, phy, + MDIO_REG_BANK_COMBO_IEEE0, + MDIO_COMBO_IEEE0_MII_CONTROL, + mii_control); } else { /* AN mode */ /* enable and restart AN */ @@ -2285,19 +2256,19 @@ static void bnx2x_initialize_sgmii_process(struct bnx2x_phy *phy, static void bnx2x_pause_resolve(struct link_vars *vars, u32 pause_result) { /* LD LP */ - switch (pause_result) { /* ASYM P ASYM P */ - case 0xb: /* 1 0 1 1 */ + switch (pause_result) { /* ASYM P ASYM P */ + case 0xb: /* 1 0 1 1 */ vars->flow_ctrl = BNX2X_FLOW_CTRL_TX; break; - case 0xe: /* 1 1 1 0 */ + case 0xe: /* 1 1 1 0 */ vars->flow_ctrl = BNX2X_FLOW_CTRL_RX; break; - case 0x5: /* 0 1 0 1 */ - case 0x7: /* 0 1 1 1 */ - case 0xd: /* 1 1 0 1 */ - case 0xf: /* 1 1 1 1 */ + case 0x5: /* 0 1 0 1 */ + case 0x7: /* 0 1 1 1 */ + case 0xd: /* 1 1 0 1 */ + case 0xf: /* 1 1 1 1 */ vars->flow_ctrl = BNX2X_FLOW_CTRL_BOTH; break; @@ -2317,24 +2288,24 @@ static u8 bnx2x_direct_parallel_detect_used(struct bnx2x_phy *phy, u16 pd_10g, status2_1000x; if (phy->req_line_speed != SPEED_AUTO_NEG) return 0; - CL45_RD_OVER_CL22(bp, phy, - MDIO_REG_BANK_SERDES_DIGITAL, - MDIO_SERDES_DIGITAL_A_1000X_STATUS2, - &status2_1000x); - CL45_RD_OVER_CL22(bp, phy, - MDIO_REG_BANK_SERDES_DIGITAL, - MDIO_SERDES_DIGITAL_A_1000X_STATUS2, - &status2_1000x); + CL22_RD_OVER_CL45(bp, phy, + MDIO_REG_BANK_SERDES_DIGITAL, + MDIO_SERDES_DIGITAL_A_1000X_STATUS2, + &status2_1000x); + CL22_RD_OVER_CL45(bp, phy, + MDIO_REG_BANK_SERDES_DIGITAL, + MDIO_SERDES_DIGITAL_A_1000X_STATUS2, + &status2_1000x); if (status2_1000x & MDIO_SERDES_DIGITAL_A_1000X_STATUS2_AN_DISABLED) { DP(NETIF_MSG_LINK, "1G parallel detect link on port %d\n", params->port); return 1; } - CL45_RD_OVER_CL22(bp, phy, - MDIO_REG_BANK_10G_PARALLEL_DETECT, - MDIO_10G_PARALLEL_DETECT_PAR_DET_10G_STATUS, - &pd_10g); + CL22_RD_OVER_CL45(bp, phy, + MDIO_REG_BANK_10G_PARALLEL_DETECT, + MDIO_10G_PARALLEL_DETECT_PAR_DET_10G_STATUS, + &pd_10g); if (pd_10g & MDIO_10G_PARALLEL_DETECT_PAR_DET_10G_STATUS_PD_LINK) { DP(NETIF_MSG_LINK, "10G parallel detect link on port %d\n", @@ -2373,14 +2344,14 @@ static void bnx2x_flow_ctrl_resolve(struct bnx2x_phy *phy, (MDIO_GP_STATUS_TOP_AN_STATUS1_CL73_AUTONEG_COMPLETE | MDIO_GP_STATUS_TOP_AN_STATUS1_CL73_MR_LP_NP_AN_ABLE)) { - CL45_RD_OVER_CL22(bp, phy, - MDIO_REG_BANK_CL73_IEEEB1, - MDIO_CL73_IEEEB1_AN_ADV1, - &ld_pause); - CL45_RD_OVER_CL22(bp, phy, - MDIO_REG_BANK_CL73_IEEEB1, - MDIO_CL73_IEEEB1_AN_LP_ADV1, - &lp_pause); + CL22_RD_OVER_CL45(bp, phy, + MDIO_REG_BANK_CL73_IEEEB1, + MDIO_CL73_IEEEB1_AN_ADV1, + &ld_pause); + CL22_RD_OVER_CL45(bp, phy, + MDIO_REG_BANK_CL73_IEEEB1, + MDIO_CL73_IEEEB1_AN_LP_ADV1, + &lp_pause); pause_result = (ld_pause & MDIO_CL73_IEEEB1_AN_ADV1_PAUSE_MASK) >> 8; @@ -2390,18 +2361,18 @@ static void bnx2x_flow_ctrl_resolve(struct bnx2x_phy *phy, DP(NETIF_MSG_LINK, "pause_result CL73 0x%x\n", pause_result); } else { - CL45_RD_OVER_CL22(bp, phy, - MDIO_REG_BANK_COMBO_IEEE0, - MDIO_COMBO_IEEE0_AUTO_NEG_ADV, - &ld_pause); - CL45_RD_OVER_CL22(bp, phy, - MDIO_REG_BANK_COMBO_IEEE0, - MDIO_COMBO_IEEE0_AUTO_NEG_LINK_PARTNER_ABILITY1, - &lp_pause); + CL22_RD_OVER_CL45(bp, phy, + MDIO_REG_BANK_COMBO_IEEE0, + MDIO_COMBO_IEEE0_AUTO_NEG_ADV, + &ld_pause); + CL22_RD_OVER_CL45(bp, phy, + MDIO_REG_BANK_COMBO_IEEE0, + MDIO_COMBO_IEEE0_AUTO_NEG_LINK_PARTNER_ABILITY1, + &lp_pause); pause_result = (ld_pause & MDIO_COMBO_IEEE0_AUTO_NEG_ADV_PAUSE_MASK)>>5; pause_result |= (lp_pause & - MDIO_COMBO_IEEE0_AUTO_NEG_ADV_PAUSE_MASK)>>7; + MDIO_COMBO_IEEE0_AUTO_NEG_ADV_PAUSE_MASK)>>7; DP(NETIF_MSG_LINK, "pause_result CL37 0x%x\n", pause_result); } @@ -2417,25 +2388,25 @@ static void bnx2x_check_fallback_to_cl37(struct bnx2x_phy *phy, u16 rx_status, ustat_val, cl37_fsm_recieved; DP(NETIF_MSG_LINK, "bnx2x_check_fallback_to_cl37\n"); /* Step 1: Make sure signal is detected */ - CL45_RD_OVER_CL22(bp, phy, - MDIO_REG_BANK_RX0, - MDIO_RX0_RX_STATUS, - &rx_status); + CL22_RD_OVER_CL45(bp, phy, + MDIO_REG_BANK_RX0, + MDIO_RX0_RX_STATUS, + &rx_status); if ((rx_status & MDIO_RX0_RX_STATUS_SIGDET) != (MDIO_RX0_RX_STATUS_SIGDET)) { DP(NETIF_MSG_LINK, "Signal is not detected. Restoring CL73." "rx_status(0x80b0) = 0x%x\n", rx_status); - CL45_WR_OVER_CL22(bp, phy, - MDIO_REG_BANK_CL73_IEEEB0, - MDIO_CL73_IEEEB0_CL73_AN_CONTROL, - MDIO_CL73_IEEEB0_CL73_AN_CONTROL_AN_EN); + CL22_WR_OVER_CL45(bp, phy, + MDIO_REG_BANK_CL73_IEEEB0, + MDIO_CL73_IEEEB0_CL73_AN_CONTROL, + MDIO_CL73_IEEEB0_CL73_AN_CONTROL_AN_EN); return; } /* Step 2: Check CL73 state machine */ - CL45_RD_OVER_CL22(bp, phy, - MDIO_REG_BANK_CL73_USERB0, - MDIO_CL73_USERB0_CL73_USTAT1, - &ustat_val); + CL22_RD_OVER_CL45(bp, phy, + MDIO_REG_BANK_CL73_USERB0, + MDIO_CL73_USERB0_CL73_USTAT1, + &ustat_val); if ((ustat_val & (MDIO_CL73_USERB0_CL73_USTAT1_LINK_STATUS_CHECK | MDIO_CL73_USERB0_CL73_USTAT1_AN_GOOD_CHECK_BAM37)) != @@ -2445,12 +2416,14 @@ static void bnx2x_check_fallback_to_cl37(struct bnx2x_phy *phy, "ustat_val(0x8371) = 0x%x\n", ustat_val); return; } - /* Step 3: Check CL37 Message Pages received to indicate LP - supports only CL37 */ - CL45_RD_OVER_CL22(bp, phy, - MDIO_REG_BANK_REMOTE_PHY, - MDIO_REMOTE_PHY_MISC_RX_STATUS, - &cl37_fsm_recieved); + /* + * Step 3: Check CL37 Message Pages received to indicate LP + * supports only CL37 + */ + CL22_RD_OVER_CL45(bp, phy, + MDIO_REG_BANK_REMOTE_PHY, + MDIO_REMOTE_PHY_MISC_RX_STATUS, + &cl37_fsm_recieved); if ((cl37_fsm_recieved & (MDIO_REMOTE_PHY_MISC_RX_STATUS_CL37_FSM_RECEIVED_OVER1G_MSG | MDIO_REMOTE_PHY_MISC_RX_STATUS_CL37_FSM_RECEIVED_BRCM_OUI_MSG)) != @@ -2461,14 +2434,18 @@ static void bnx2x_check_fallback_to_cl37(struct bnx2x_phy *phy, cl37_fsm_recieved); return; } - /* The combined cl37/cl73 fsm state information indicating that we are - connected to a device which does not support cl73, but does support - cl37 BAM. In this case we disable cl73 and restart cl37 auto-neg */ + /* + * The combined cl37/cl73 fsm state information indicating that + * we are connected to a device which does not support cl73, but + * does support cl37 BAM. In this case we disable cl73 and + * restart cl37 auto-neg + */ + /* Disable CL73 */ - CL45_WR_OVER_CL22(bp, phy, - MDIO_REG_BANK_CL73_IEEEB0, - MDIO_CL73_IEEEB0_CL73_AN_CONTROL, - 0); + CL22_WR_OVER_CL45(bp, phy, + MDIO_REG_BANK_CL73_IEEEB0, + MDIO_CL73_IEEEB0_CL73_AN_CONTROL, + 0); /* Restart CL37 autoneg */ bnx2x_restart_autoneg(phy, params, 0); DP(NETIF_MSG_LINK, "Disabling CL73, and restarting CL37 autoneg\n"); @@ -2493,14 +2470,14 @@ static u8 bnx2x_link_settings_status(struct bnx2x_phy *phy, struct link_vars *vars) { struct bnx2x *bp = params->bp; - u16 new_line_speed , gp_status; + u16 new_line_speed, gp_status; u8 rc = 0; /* Read gp_status */ - CL45_RD_OVER_CL22(bp, phy, - MDIO_REG_BANK_GP_STATUS, - MDIO_GP_STATUS_TOP_AN_STATUS1, - &gp_status); + CL22_RD_OVER_CL45(bp, phy, + MDIO_REG_BANK_GP_STATUS, + MDIO_GP_STATUS_TOP_AN_STATUS1, + &gp_status); if (phy->req_line_speed == SPEED_AUTO_NEG) vars->link_status |= LINK_STATUS_AUTO_NEGOTIATE_ENABLED; @@ -2637,9 +2614,9 @@ static void bnx2x_set_gmii_tx_driver(struct link_params *params) u16 bank; /* read precomp */ - CL45_RD_OVER_CL22(bp, phy, - MDIO_REG_BANK_OVER_1G, - MDIO_OVER_1G_LP_UP2, &lp_up2); + CL22_RD_OVER_CL45(bp, phy, + MDIO_REG_BANK_OVER_1G, + MDIO_OVER_1G_LP_UP2, &lp_up2); /* bits [10:7] at lp_up2, positioned at [15:12] */ lp_up2 = (((lp_up2 & MDIO_OVER_1G_LP_UP2_PREEMPHASIS_MASK) >> @@ -2651,18 +2628,18 @@ static void bnx2x_set_gmii_tx_driver(struct link_params *params) for (bank = MDIO_REG_BANK_TX0; bank <= MDIO_REG_BANK_TX3; bank += (MDIO_REG_BANK_TX1 - MDIO_REG_BANK_TX0)) { - CL45_RD_OVER_CL22(bp, phy, - bank, - MDIO_TX0_TX_DRIVER, &tx_driver); + CL22_RD_OVER_CL45(bp, phy, + bank, + MDIO_TX0_TX_DRIVER, &tx_driver); /* replace tx_driver bits [15:12] */ if (lp_up2 != (tx_driver & MDIO_TX0_TX_DRIVER_PREEMPHASIS_MASK)) { tx_driver &= ~MDIO_TX0_TX_DRIVER_PREEMPHASIS_MASK; tx_driver |= lp_up2; - CL45_WR_OVER_CL22(bp, phy, - bank, - MDIO_TX0_TX_DRIVER, tx_driver); + CL22_WR_OVER_CL45(bp, phy, + bank, + MDIO_TX0_TX_DRIVER, tx_driver); } } } @@ -2676,10 +2653,10 @@ static u8 bnx2x_emac_program(struct link_params *params, DP(NETIF_MSG_LINK, "setting link speed & duplex\n"); bnx2x_bits_dis(bp, GRCBASE_EMAC0 + port*0x400 + - EMAC_REG_EMAC_MODE, - (EMAC_MODE_25G_MODE | - EMAC_MODE_PORT_MII_10M | - EMAC_MODE_HALF_DUPLEX)); + EMAC_REG_EMAC_MODE, + (EMAC_MODE_25G_MODE | + EMAC_MODE_PORT_MII_10M | + EMAC_MODE_HALF_DUPLEX)); switch (vars->line_speed) { case SPEED_10: mode |= EMAC_MODE_PORT_MII_10M; @@ -2707,8 +2684,8 @@ static u8 bnx2x_emac_program(struct link_params *params, if (vars->duplex == DUPLEX_HALF) mode |= EMAC_MODE_HALF_DUPLEX; bnx2x_bits_en(bp, - GRCBASE_EMAC0 + port*0x400 + EMAC_REG_EMAC_MODE, - mode); + GRCBASE_EMAC0 + port*0x400 + EMAC_REG_EMAC_MODE, + mode); bnx2x_set_led(params, vars, LED_MODE_OPER, vars->line_speed); return 0; @@ -2723,7 +2700,7 @@ static void bnx2x_set_preemphasis(struct bnx2x_phy *phy, for (bank = MDIO_REG_BANK_RX0, i = 0; bank <= MDIO_REG_BANK_RX3; bank += (MDIO_REG_BANK_RX1-MDIO_REG_BANK_RX0), i++) { - CL45_WR_OVER_CL22(bp, phy, + CL22_WR_OVER_CL45(bp, phy, bank, MDIO_RX0_RX_EQ_BOOST, phy->rx_preemphasis[i]); @@ -2731,7 +2708,7 @@ static void bnx2x_set_preemphasis(struct bnx2x_phy *phy, for (bank = MDIO_REG_BANK_TX0, i = 0; bank <= MDIO_REG_BANK_TX3; bank += (MDIO_REG_BANK_TX1 - MDIO_REG_BANK_TX0), i++) { - CL45_WR_OVER_CL22(bp, phy, + CL22_WR_OVER_CL45(bp, phy, bank, MDIO_TX0_TX_DRIVER, phy->tx_preemphasis[i]); @@ -2754,7 +2731,7 @@ static void bnx2x_init_internal_phy(struct bnx2x_phy *phy, /* forced speed requested? */ if (vars->line_speed != SPEED_AUTO_NEG || (SINGLE_MEDIA_DIRECT(params) && - params->loopback_mode == LOOPBACK_EXT)) { + params->loopback_mode == LOOPBACK_EXT)) { DP(NETIF_MSG_LINK, "not SGMII, no AN\n"); /* disable autoneg */ @@ -2771,7 +2748,7 @@ static void bnx2x_init_internal_phy(struct bnx2x_phy *phy, /* program duplex & pause advertisement (for aneg) */ bnx2x_set_ieee_aneg_advertisment(phy, params, - vars->ieee_fc); + vars->ieee_fc); /* enable autoneg */ bnx2x_set_autoneg(phy, params, vars, enable_cl73); @@ -2842,7 +2819,8 @@ static u8 bnx2x_init_xgxs(struct bnx2x_phy *phy, } static u16 bnx2x_wait_reset_complete(struct bnx2x *bp, - struct bnx2x_phy *phy) + struct bnx2x_phy *phy, + struct link_params *params) { u16 cnt, ctrl; /* Wait for soft reset to get cleared upto 1 sec */ @@ -2853,6 +2831,11 @@ static u16 bnx2x_wait_reset_complete(struct bnx2x *bp, break; msleep(1); } + + if (cnt == 1000) + netdev_err(bp->dev, "Warning: PHY was not initialized," + " Port %d\n", + params->port); DP(NETIF_MSG_LINK, "control reg 0x%x (after %d ms)\n", ctrl, cnt); return cnt; } @@ -2863,9 +2846,7 @@ static void bnx2x_link_int_enable(struct link_params *params) u32 mask; struct bnx2x *bp = params->bp; - /* setting the status to report on link up - for either XGXS or SerDes */ - + /* Setting the status to report on link up for either XGXS or SerDes */ if (params->switch_cfg == SWITCH_CFG_10G) { mask = (NIG_MASK_XGXS0_LINK10G | NIG_MASK_XGXS0_LINK_STATUS); @@ -2908,7 +2889,7 @@ static void bnx2x_rearm_latch_signal(struct bnx2x *bp, u8 port, { u32 latch_status = 0; - /** + /* * Disable the MI INT ( external phy int ) by writing 1 to the * status register. Link down indication is high-active-signal, * so in this case we need to write the status to clear the XOR @@ -2933,27 +2914,30 @@ static void bnx2x_rearm_latch_signal(struct bnx2x *bp, u8 port, /* For all latched-signal=up : Re-Arm Latch signals */ REG_WR(bp, NIG_REG_LATCH_STATUS_0 + port*8, - (latch_status & 0xfffe) | (latch_status & 1)); + (latch_status & 0xfffe) | (latch_status & 1)); } /* For all latched-signal=up,Write original_signal to status */ } static void bnx2x_link_int_ack(struct link_params *params, - struct link_vars *vars, u8 is_10g) + struct link_vars *vars, u8 is_10g) { struct bnx2x *bp = params->bp; u8 port = params->port; - /* first reset all status - * we assume only one line will be change at a time */ + /* + * First reset all status we assume only one line will be + * change at a time + */ bnx2x_bits_dis(bp, NIG_REG_STATUS_INTERRUPT_PORT0 + port*4, - (NIG_STATUS_XGXS0_LINK10G | - NIG_STATUS_XGXS0_LINK_STATUS | - NIG_STATUS_SERDES0_LINK_STATUS)); + (NIG_STATUS_XGXS0_LINK10G | + NIG_STATUS_XGXS0_LINK_STATUS | + NIG_STATUS_SERDES0_LINK_STATUS)); if (vars->phy_link_up) { if (is_10g) { - /* Disable the 10G link interrupt - * by writing 1 to the status register + /* + * Disable the 10G link interrupt by writing 1 to the + * status register */ DP(NETIF_MSG_LINK, "10G XGXS phy link up\n"); bnx2x_bits_en(bp, @@ -2961,9 +2945,9 @@ static void bnx2x_link_int_ack(struct link_params *params, NIG_STATUS_XGXS0_LINK10G); } else if (params->switch_cfg == SWITCH_CFG_10G) { - /* Disable the link interrupt - * by writing 1 to the relevant lane - * in the status register + /* + * Disable the link interrupt by writing 1 to the + * relevant lane in the status register */ u32 ser_lane = ((params->lane_config & PORT_HW_CFG_LANE_SWAP_CFG_MASTER_MASK) >> @@ -2978,8 +2962,9 @@ static void bnx2x_link_int_ack(struct link_params *params, } else { /* SerDes */ DP(NETIF_MSG_LINK, "SerDes phy link up\n"); - /* Disable the link interrupt - * by writing 1 to the status register + /* + * Disable the link interrupt by writing 1 to the status + * register */ bnx2x_bits_en(bp, NIG_REG_STATUS_INTERRUPT_PORT0 + port*4, @@ -3059,8 +3044,7 @@ u8 bnx2x_get_ext_phy_fw_version(struct link_params *params, u8 driver_loaded, } if ((params->num_phys == MAX_PHYS) && (params->phy[EXT_PHY2].ver_addr != 0)) { - spirom_ver = REG_RD(bp, - params->phy[EXT_PHY2].ver_addr); + spirom_ver = REG_RD(bp, params->phy[EXT_PHY2].ver_addr); if (params->phy[EXT_PHY2].format_fw_ver) { *ver_p = '/'; ver_p++; @@ -3089,29 +3073,27 @@ static void bnx2x_set_xgxs_loopback(struct bnx2x_phy *phy, /* change the uni_phy_addr in the nig */ md_devad = REG_RD(bp, (NIG_REG_XGXS0_CTRL_MD_DEVAD + - port*0x18)); + port*0x18)); REG_WR(bp, NIG_REG_XGXS0_CTRL_MD_DEVAD + port*0x18, 0x5); bnx2x_cl45_write(bp, phy, - 5, - (MDIO_REG_BANK_AER_BLOCK + - (MDIO_AER_BLOCK_AER_REG & 0xf)), - 0x2800); + 5, + (MDIO_REG_BANK_AER_BLOCK + + (MDIO_AER_BLOCK_AER_REG & 0xf)), + 0x2800); bnx2x_cl45_write(bp, phy, - 5, - (MDIO_REG_BANK_CL73_IEEEB0 + - (MDIO_CL73_IEEEB0_CL73_AN_CONTROL & 0xf)), - 0x6041); + 5, + (MDIO_REG_BANK_CL73_IEEEB0 + + (MDIO_CL73_IEEEB0_CL73_AN_CONTROL & 0xf)), + 0x6041); msleep(200); /* set aer mmd back */ bnx2x_set_aer_mmd_xgxs(params, phy); /* and md_devad */ - REG_WR(bp, NIG_REG_XGXS0_CTRL_MD_DEVAD + port*0x18, - md_devad); - + REG_WR(bp, NIG_REG_XGXS0_CTRL_MD_DEVAD + port*0x18, md_devad); } else { u16 mii_ctrl; DP(NETIF_MSG_LINK, "XGXS 1G loopback enable\n"); @@ -3152,26 +3134,26 @@ u8 bnx2x_set_led(struct link_params *params, case LED_MODE_OFF: REG_WR(bp, NIG_REG_LED_10G_P0 + port*4, 0); REG_WR(bp, NIG_REG_LED_MODE_P0 + port*4, - SHARED_HW_CFG_LED_MAC1); + SHARED_HW_CFG_LED_MAC1); tmp = EMAC_RD(bp, EMAC_REG_EMAC_LED); EMAC_WR(bp, EMAC_REG_EMAC_LED, (tmp | EMAC_LED_OVERRIDE)); break; case LED_MODE_OPER: - /** + /* * For all other phys, OPER mode is same as ON, so in case * link is down, do nothing - **/ + */ if (!vars->link_up) break; case LED_MODE_ON: if (params->phy[EXT_PHY1].type == PORT_HW_CFG_XGXS_EXT_PHY_TYPE_BCM8727 && CHIP_IS_E2(bp) && params->num_phys == 2) { - /** - * This is a work-around for E2+8727 Configurations - */ + /* + * This is a work-around for E2+8727 Configurations + */ if (mode == LED_MODE_ON || speed == SPEED_10000){ REG_WR(bp, NIG_REG_LED_MODE_P0 + port*4, 0); @@ -3183,41 +3165,40 @@ u8 bnx2x_set_led(struct link_params *params, return rc; } } else if (SINGLE_MEDIA_DIRECT(params)) { - /** - * This is a work-around for HW issue found when link - * is up in CL73 - */ + /* + * This is a work-around for HW issue found when link + * is up in CL73 + */ REG_WR(bp, NIG_REG_LED_MODE_P0 + port*4, 0); REG_WR(bp, NIG_REG_LED_10G_P0 + port*4, 1); } else { - REG_WR(bp, NIG_REG_LED_MODE_P0 + port*4, - hw_led_mode); + REG_WR(bp, NIG_REG_LED_MODE_P0 + port*4, hw_led_mode); } - REG_WR(bp, NIG_REG_LED_CONTROL_OVERRIDE_TRAFFIC_P0 + - port*4, 0); + REG_WR(bp, NIG_REG_LED_CONTROL_OVERRIDE_TRAFFIC_P0 + port*4, 0); /* Set blinking rate to ~15.9Hz */ REG_WR(bp, NIG_REG_LED_CONTROL_BLINK_RATE_P0 + port*4, - LED_BLINK_RATE_VAL); + LED_BLINK_RATE_VAL); REG_WR(bp, NIG_REG_LED_CONTROL_BLINK_RATE_ENA_P0 + - port*4, 1); + port*4, 1); tmp = EMAC_RD(bp, EMAC_REG_EMAC_LED); - EMAC_WR(bp, EMAC_REG_EMAC_LED, - (tmp & (~EMAC_LED_OVERRIDE))); + EMAC_WR(bp, EMAC_REG_EMAC_LED, (tmp & (~EMAC_LED_OVERRIDE))); if (CHIP_IS_E1(bp) && ((speed == SPEED_2500) || (speed == SPEED_1000) || (speed == SPEED_100) || (speed == SPEED_10))) { - /* On Everest 1 Ax chip versions for speeds less than - 10G LED scheme is different */ + /* + * On Everest 1 Ax chip versions for speeds less than + * 10G LED scheme is different + */ REG_WR(bp, NIG_REG_LED_CONTROL_OVERRIDE_TRAFFIC_P0 - + port*4, 1); + + port*4, 1); REG_WR(bp, NIG_REG_LED_CONTROL_TRAFFIC_P0 + - port*4, 0); + port*4, 0); REG_WR(bp, NIG_REG_LED_CONTROL_BLINK_TRAFFIC_P0 + - port*4, 1); + port*4, 1); } break; @@ -3231,7 +3212,7 @@ u8 bnx2x_set_led(struct link_params *params, } -/** +/* * This function comes to reflect the actual link state read DIRECTLY from the * HW */ @@ -3243,10 +3224,10 @@ u8 bnx2x_test_link(struct link_params *params, struct link_vars *vars, u8 ext_phy_link_up = 0, serdes_phy_type; struct link_vars temp_vars; - CL45_RD_OVER_CL22(bp, ¶ms->phy[INT_PHY], - MDIO_REG_BANK_GP_STATUS, - MDIO_GP_STATUS_TOP_AN_STATUS1, - &gp_status); + CL22_RD_OVER_CL45(bp, ¶ms->phy[INT_PHY], + MDIO_REG_BANK_GP_STATUS, + MDIO_GP_STATUS_TOP_AN_STATUS1, + &gp_status); /* link is up only if both local phy and external phy are up */ if (!(gp_status & MDIO_GP_STATUS_TOP_AN_STATUS1_LINK_STATUS)) return -ESRCH; @@ -3290,15 +3271,15 @@ static u8 bnx2x_link_initialize(struct link_params *params, u8 rc = 0; u8 phy_index, non_ext_phy; struct bnx2x *bp = params->bp; - /** - * In case of external phy existence, the line speed would be the - * line speed linked up by the external phy. In case it is direct - * only, then the line_speed during initialization will be - * equal to the req_line_speed - */ + /* + * In case of external phy existence, the line speed would be the + * line speed linked up by the external phy. In case it is direct + * only, then the line_speed during initialization will be + * equal to the req_line_speed + */ vars->line_speed = params->phy[INT_PHY].req_line_speed; - /** + /* * Initialize the internal phy in case this is a direct board * (no external phys), or this board has external phy which requires * to first. @@ -3326,17 +3307,16 @@ static u8 bnx2x_link_initialize(struct link_params *params, if (!non_ext_phy) for (phy_index = EXT_PHY1; phy_index < params->num_phys; phy_index++) { - /** + /* * No need to initialize second phy in case of first * phy only selection. In case of second phy, we do * need to initialize the first phy, since they are * connected. - **/ + */ if (phy_index == EXT_PHY2 && (bnx2x_phy_selection(params) == PORT_HW_CFG_PHY_SELECTION_FIRST_PHY)) { - DP(NETIF_MSG_LINK, "Not initializing" - "second phy\n"); + DP(NETIF_MSG_LINK, "Ignoring second phy\n"); continue; } params->phy[phy_index].config_init( @@ -3358,9 +3338,8 @@ static void bnx2x_int_link_reset(struct bnx2x_phy *phy, struct link_params *params) { /* reset the SerDes/XGXS */ - REG_WR(params->bp, GRCBASE_MISC + - MISC_REGISTERS_RESET_REG_3_CLEAR, - (0x1ff << (params->port*16))); + REG_WR(params->bp, GRCBASE_MISC + MISC_REGISTERS_RESET_REG_3_CLEAR, + (0x1ff << (params->port*16))); } static void bnx2x_common_ext_link_reset(struct bnx2x_phy *phy, @@ -3374,11 +3353,11 @@ static void bnx2x_common_ext_link_reset(struct bnx2x_phy *phy, else gpio_port = params->port; bnx2x_set_gpio(bp, MISC_REGISTERS_GPIO_1, - MISC_REGISTERS_GPIO_OUTPUT_LOW, - gpio_port); + MISC_REGISTERS_GPIO_OUTPUT_LOW, + gpio_port); bnx2x_set_gpio(bp, MISC_REGISTERS_GPIO_2, - MISC_REGISTERS_GPIO_OUTPUT_LOW, - gpio_port); + MISC_REGISTERS_GPIO_OUTPUT_LOW, + gpio_port); DP(NETIF_MSG_LINK, "reset external PHY\n"); } @@ -3409,9 +3388,8 @@ static u8 bnx2x_update_link_down(struct link_params *params, /* reset BigMac */ bnx2x_bmac_rx_disable(bp, params->port); - REG_WR(bp, GRCBASE_MISC + - MISC_REGISTERS_RESET_REG_2_CLEAR, - (MISC_REGISTERS_RESET_REG_2_RST_BMAC0 << port)); + REG_WR(bp, GRCBASE_MISC + MISC_REGISTERS_RESET_REG_2_CLEAR, + (MISC_REGISTERS_RESET_REG_2_RST_BMAC0 << port)); return 0; } @@ -3462,7 +3440,7 @@ static u8 bnx2x_update_link_up(struct link_params *params, msleep(20); return rc; } -/** +/* * The bnx2x_link_update function should be called upon link * interrupt. * Link is considered up as follows: @@ -3501,12 +3479,11 @@ u8 bnx2x_link_update(struct link_params *params, struct link_vars *vars) REG_RD(bp, NIG_REG_STATUS_INTERRUPT_PORT0 + port*4)); is_mi_int = (u8)(REG_RD(bp, NIG_REG_EMAC0_STATUS_MISC_MI_INT + - port*0x18) > 0); + port*0x18) > 0); DP(NETIF_MSG_LINK, "int_mask 0x%x MI_INT %x, SERDES_LINK %x\n", REG_RD(bp, NIG_REG_MASK_INTERRUPT_PORT0 + port*4), is_mi_int, - REG_RD(bp, - NIG_REG_SERDES0_STATUS_LINK_STATUS + port*0x3c)); + REG_RD(bp, NIG_REG_SERDES0_STATUS_LINK_STATUS + port*0x3c)); DP(NETIF_MSG_LINK, " 10G %x, XGXS_LINK %x\n", REG_RD(bp, NIG_REG_XGXS0_STATUS_LINK10G + port*0x68), @@ -3515,14 +3492,14 @@ u8 bnx2x_link_update(struct link_params *params, struct link_vars *vars) /* disable emac */ REG_WR(bp, NIG_REG_NIG_EMAC0_EN + port*4, 0); - /** - * Step 1: - * Check external link change only for external phys, and apply - * priority selection between them in case the link on both phys - * is up. Note that the instead of the common vars, a temporary - * vars argument is used since each phy may have different link/ - * speed/duplex result - */ + /* + * Step 1: + * Check external link change only for external phys, and apply + * priority selection between them in case the link on both phys + * is up. Note that the instead of the common vars, a temporary + * vars argument is used since each phy may have different link/ + * speed/duplex result + */ for (phy_index = EXT_PHY1; phy_index < params->num_phys; phy_index++) { struct bnx2x_phy *phy = ¶ms->phy[phy_index]; @@ -3547,22 +3524,22 @@ u8 bnx2x_link_update(struct link_params *params, struct link_vars *vars) switch (bnx2x_phy_selection(params)) { case PORT_HW_CFG_PHY_SELECTION_HARDWARE_DEFAULT: case PORT_HW_CFG_PHY_SELECTION_FIRST_PHY_PRIORITY: - /** + /* * In this option, the first PHY makes sure to pass the * traffic through itself only. * Its not clear how to reset the link on the second phy - **/ + */ active_external_phy = EXT_PHY1; break; case PORT_HW_CFG_PHY_SELECTION_SECOND_PHY_PRIORITY: - /** + /* * In this option, the first PHY makes sure to pass the * traffic through the second PHY. - **/ + */ active_external_phy = EXT_PHY2; break; default: - /** + /* * Link indication on both PHYs with the following cases * is invalid: * - FIRST_PHY means that second phy wasn't initialized, @@ -3570,7 +3547,7 @@ u8 bnx2x_link_update(struct link_params *params, struct link_vars *vars) * - SECOND_PHY means that first phy should not be able * to link up by itself (using configuration) * - DEFAULT should be overriden during initialiazation - **/ + */ DP(NETIF_MSG_LINK, "Invalid link indication" "mpc=0x%x. DISABLING LINK !!!\n", params->multi_phy_config); @@ -3580,18 +3557,18 @@ u8 bnx2x_link_update(struct link_params *params, struct link_vars *vars) } } prev_line_speed = vars->line_speed; - /** - * Step 2: - * Read the status of the internal phy. In case of - * DIRECT_SINGLE_MEDIA board, this link is the external link, - * otherwise this is the link between the 577xx and the first - * external phy - */ + /* + * Step 2: + * Read the status of the internal phy. In case of + * DIRECT_SINGLE_MEDIA board, this link is the external link, + * otherwise this is the link between the 577xx and the first + * external phy + */ if (params->phy[INT_PHY].read_status) params->phy[INT_PHY].read_status( ¶ms->phy[INT_PHY], params, vars); - /** + /* * The INT_PHY flow control reside in the vars. This include the * case where the speed or flow control are not set to AUTO. * Otherwise, the active external phy flow control result is set @@ -3601,13 +3578,13 @@ u8 bnx2x_link_update(struct link_params *params, struct link_vars *vars) */ if (active_external_phy > INT_PHY) { vars->flow_ctrl = phy_vars[active_external_phy].flow_ctrl; - /** + /* * Link speed is taken from the XGXS. AN and FC result from * the external phy. */ vars->link_status |= phy_vars[active_external_phy].link_status; - /** + /* * if active_external_phy is first PHY and link is up - disable * disable TX on second external PHY */ @@ -3643,7 +3620,7 @@ u8 bnx2x_link_update(struct link_params *params, struct link_vars *vars) DP(NETIF_MSG_LINK, "vars->flow_ctrl = 0x%x, vars->link_status = 0x%x," " ext_phy_line_speed = %d\n", vars->flow_ctrl, vars->link_status, ext_phy_line_speed); - /** + /* * Upon link speed change set the NIG into drain mode. Comes to * deals with possible FIFO glitch due to clk change when speed * is decreased without link down indicator @@ -3658,8 +3635,8 @@ u8 bnx2x_link_update(struct link_params *params, struct link_vars *vars) ext_phy_line_speed); vars->phy_link_up = 0; } else if (prev_line_speed != vars->line_speed) { - REG_WR(bp, NIG_REG_EGRESS_DRAIN0_MODE - + params->port*4, 0); + REG_WR(bp, NIG_REG_EGRESS_DRAIN0_MODE + params->port*4, + 0); msleep(1); } } @@ -3674,14 +3651,14 @@ u8 bnx2x_link_update(struct link_params *params, struct link_vars *vars) bnx2x_link_int_ack(params, vars, link_10g); - /** - * In case external phy link is up, and internal link is down - * (not initialized yet probably after link initialization, it - * needs to be initialized. - * Note that after link down-up as result of cable plug, the xgxs - * link would probably become up again without the need - * initialize it - */ + /* + * In case external phy link is up, and internal link is down + * (not initialized yet probably after link initialization, it + * needs to be initialized. + * Note that after link down-up as result of cable plug, the xgxs + * link would probably become up again without the need + * initialize it + */ if (!(SINGLE_MEDIA_DIRECT(params))) { DP(NETIF_MSG_LINK, "ext_phy_link_up = %d, int_link_up = %d," " init_preceding = %d\n", ext_phy_link_up, @@ -3701,9 +3678,9 @@ u8 bnx2x_link_update(struct link_params *params, struct link_vars *vars) vars); } } - /** - * Link is up only if both local phy and external phy (in case of - * non-direct board) are up + /* + * Link is up only if both local phy and external phy (in case of + * non-direct board) are up */ vars->link_up = (vars->phy_link_up && (ext_phy_link_up || @@ -3724,10 +3701,10 @@ u8 bnx2x_link_update(struct link_params *params, struct link_vars *vars) void bnx2x_ext_phy_hw_reset(struct bnx2x *bp, u8 port) { bnx2x_set_gpio(bp, MISC_REGISTERS_GPIO_1, - MISC_REGISTERS_GPIO_OUTPUT_LOW, port); + MISC_REGISTERS_GPIO_OUTPUT_LOW, port); msleep(1); bnx2x_set_gpio(bp, MISC_REGISTERS_GPIO_1, - MISC_REGISTERS_GPIO_OUTPUT_HIGH, port); + MISC_REGISTERS_GPIO_OUTPUT_HIGH, port); } static void bnx2x_save_spirom_version(struct bnx2x *bp, u8 port, @@ -3747,9 +3724,9 @@ static void bnx2x_save_bcm_spirom_ver(struct bnx2x *bp, u16 fw_ver1, fw_ver2; bnx2x_cl45_read(bp, phy, MDIO_PMA_DEVAD, - MDIO_PMA_REG_ROM_VER1, &fw_ver1); + MDIO_PMA_REG_ROM_VER1, &fw_ver1); bnx2x_cl45_read(bp, phy, MDIO_PMA_DEVAD, - MDIO_PMA_REG_ROM_VER2, &fw_ver2); + MDIO_PMA_REG_ROM_VER2, &fw_ver2); bnx2x_save_spirom_version(bp, port, (u32)(fw_ver1<<16 | fw_ver2), phy->ver_addr); } @@ -3770,7 +3747,7 @@ static void bnx2x_ext_phy_set_pause(struct link_params *params, if ((vars->ieee_fc & MDIO_COMBO_IEEE0_AUTO_NEG_ADV_PAUSE_ASYMMETRIC) == MDIO_COMBO_IEEE0_AUTO_NEG_ADV_PAUSE_ASYMMETRIC) { - val |= MDIO_AN_REG_ADV_PAUSE_ASYMMETRIC; + val |= MDIO_AN_REG_ADV_PAUSE_ASYMMETRIC; } if ((vars->ieee_fc & MDIO_COMBO_IEEE0_AUTO_NEG_ADV_PAUSE_BOTH) == @@ -3801,11 +3778,11 @@ static u8 bnx2x_ext_phy_resolve_fc(struct bnx2x_phy *phy, else if (vars->link_status & LINK_STATUS_AUTO_NEGOTIATE_COMPLETE) { ret = 1; bnx2x_cl45_read(bp, phy, - MDIO_AN_DEVAD, - MDIO_AN_REG_ADV_PAUSE, &ld_pause); + MDIO_AN_DEVAD, + MDIO_AN_REG_ADV_PAUSE, &ld_pause); bnx2x_cl45_read(bp, phy, - MDIO_AN_DEVAD, - MDIO_AN_REG_LP_AUTO_NEG, &lp_pause); + MDIO_AN_DEVAD, + MDIO_AN_REG_LP_AUTO_NEG, &lp_pause); pause_result = (ld_pause & MDIO_AN_REG_ADV_PAUSE_MASK) >> 8; pause_result |= (lp_pause & @@ -3881,31 +3858,31 @@ static u8 bnx2x_8073_8727_external_rom_boot(struct bnx2x *bp, /* Boot port from external ROM */ /* EDC grst */ bnx2x_cl45_write(bp, phy, - MDIO_PMA_DEVAD, - MDIO_PMA_REG_GEN_CTRL, - 0x0001); + MDIO_PMA_DEVAD, + MDIO_PMA_REG_GEN_CTRL, + 0x0001); /* ucode reboot and rst */ bnx2x_cl45_write(bp, phy, - MDIO_PMA_DEVAD, - MDIO_PMA_REG_GEN_CTRL, - 0x008c); + MDIO_PMA_DEVAD, + MDIO_PMA_REG_GEN_CTRL, + 0x008c); bnx2x_cl45_write(bp, phy, - MDIO_PMA_DEVAD, - MDIO_PMA_REG_MISC_CTRL1, 0x0001); + MDIO_PMA_DEVAD, + MDIO_PMA_REG_MISC_CTRL1, 0x0001); /* Reset internal microprocessor */ bnx2x_cl45_write(bp, phy, - MDIO_PMA_DEVAD, - MDIO_PMA_REG_GEN_CTRL, - MDIO_PMA_REG_GEN_CTRL_ROM_MICRO_RESET); + MDIO_PMA_DEVAD, + MDIO_PMA_REG_GEN_CTRL, + MDIO_PMA_REG_GEN_CTRL_ROM_MICRO_RESET); /* Release srst bit */ bnx2x_cl45_write(bp, phy, - MDIO_PMA_DEVAD, - MDIO_PMA_REG_GEN_CTRL, - MDIO_PMA_REG_GEN_CTRL_ROM_RESET_INTERNAL_MP); + MDIO_PMA_DEVAD, + MDIO_PMA_REG_GEN_CTRL, + MDIO_PMA_REG_GEN_CTRL_ROM_RESET_INTERNAL_MP); /* Delay 100ms per the PHY specifications */ msleep(100); @@ -3936,8 +3913,8 @@ static u8 bnx2x_8073_8727_external_rom_boot(struct bnx2x *bp, /* Clear ser_boot_ctl bit */ bnx2x_cl45_write(bp, phy, - MDIO_PMA_DEVAD, - MDIO_PMA_REG_MISC_CTRL1, 0x0000); + MDIO_PMA_DEVAD, + MDIO_PMA_REG_MISC_CTRL1, 0x0000); bnx2x_save_bcm_spirom_ver(bp, phy, port); DP(NETIF_MSG_LINK, @@ -3958,8 +3935,8 @@ static u8 bnx2x_8073_is_snr_needed(struct bnx2x *bp, struct bnx2x_phy *phy) /* Read 8073 HW revision*/ bnx2x_cl45_read(bp, phy, - MDIO_PMA_DEVAD, - MDIO_PMA_REG_8073_CHIP_REV, &val); + MDIO_PMA_DEVAD, + MDIO_PMA_REG_8073_CHIP_REV, &val); if (val != 1) { /* No need to workaround in 8073 A1 */ @@ -3967,8 +3944,8 @@ static u8 bnx2x_8073_is_snr_needed(struct bnx2x *bp, struct bnx2x_phy *phy) } bnx2x_cl45_read(bp, phy, - MDIO_PMA_DEVAD, - MDIO_PMA_REG_ROM_VER2, &val); + MDIO_PMA_DEVAD, + MDIO_PMA_REG_ROM_VER2, &val); /* SNR should be applied only for version 0x102 */ if (val != 0x102) @@ -3982,8 +3959,8 @@ static u8 bnx2x_8073_xaui_wa(struct bnx2x *bp, struct bnx2x_phy *phy) u16 val, cnt, cnt1 ; bnx2x_cl45_read(bp, phy, - MDIO_PMA_DEVAD, - MDIO_PMA_REG_8073_CHIP_REV, &val); + MDIO_PMA_DEVAD, + MDIO_PMA_REG_8073_CHIP_REV, &val); if (val > 0) { /* No need to workaround in 8073 A1 */ @@ -3991,26 +3968,32 @@ static u8 bnx2x_8073_xaui_wa(struct bnx2x *bp, struct bnx2x_phy *phy) } /* XAUI workaround in 8073 A0: */ - /* After loading the boot ROM and restarting Autoneg, - poll Dev1, Reg $C820: */ + /* + * After loading the boot ROM and restarting Autoneg, poll + * Dev1, Reg $C820: + */ for (cnt = 0; cnt < 1000; cnt++) { bnx2x_cl45_read(bp, phy, - MDIO_PMA_DEVAD, - MDIO_PMA_REG_8073_SPEED_LINK_STATUS, - &val); - /* If bit [14] = 0 or bit [13] = 0, continue on with - system initialization (XAUI work-around not required, - as these bits indicate 2.5G or 1G link up). */ + MDIO_PMA_DEVAD, + MDIO_PMA_REG_8073_SPEED_LINK_STATUS, + &val); + /* + * If bit [14] = 0 or bit [13] = 0, continue on with + * system initialization (XAUI work-around not required, as + * these bits indicate 2.5G or 1G link up). + */ if (!(val & (1<<14)) || !(val & (1<<13))) { DP(NETIF_MSG_LINK, "XAUI work-around not required\n"); return 0; } else if (!(val & (1<<15))) { - DP(NETIF_MSG_LINK, "clc bit 15 went off\n"); - /* If bit 15 is 0, then poll Dev1, Reg $C841 until - it's MSB (bit 15) goes to 1 (indicating that the - XAUI workaround has completed), - then continue on with system initialization.*/ + DP(NETIF_MSG_LINK, "bit 15 went off\n"); + /* + * If bit 15 is 0, then poll Dev1, Reg $C841 until it's + * MSB (bit15) goes to 1 (indicating that the XAUI + * workaround has completed), then continue on with + * system initialization. + */ for (cnt1 = 0; cnt1 < 1000; cnt1++) { bnx2x_cl45_read(bp, phy, MDIO_PMA_DEVAD, @@ -4093,10 +4076,10 @@ static u8 bnx2x_8073_config_init(struct bnx2x_phy *phy, gpio_port = params->port; /* Restore normal power mode*/ bnx2x_set_gpio(bp, MISC_REGISTERS_GPIO_2, - MISC_REGISTERS_GPIO_OUTPUT_HIGH, gpio_port); + MISC_REGISTERS_GPIO_OUTPUT_HIGH, gpio_port); bnx2x_set_gpio(bp, MISC_REGISTERS_GPIO_1, - MISC_REGISTERS_GPIO_OUTPUT_HIGH, gpio_port); + MISC_REGISTERS_GPIO_OUTPUT_HIGH, gpio_port); /* enable LASI */ bnx2x_cl45_write(bp, phy, @@ -4114,10 +4097,6 @@ static u8 bnx2x_8073_config_init(struct bnx2x_phy *phy, DP(NETIF_MSG_LINK, "Before rom RX_ALARM(port1): 0x%x\n", tmp1); - /** - * If this is forced speed, set to KR or KX (all other are not - * supported) - */ /* Swap polarity if required - Must be done only in non-1G mode */ if (params->lane_config & PORT_HW_CFG_SWAP_PHY_POLARITY_ENABLED) { /* Configure the 8073 to swap _P and _N of the KR lines */ @@ -4160,8 +4139,10 @@ static u8 bnx2x_8073_config_init(struct bnx2x_phy *phy, val = (1<<7); } else if (phy->req_line_speed == SPEED_2500) { val = (1<<5); - /* Note that 2.5G works only - when used with 1G advertisment */ + /* + * Note that 2.5G works only when used with 1G + * advertisment + */ } else val = (1<<5); } else { @@ -4170,8 +4151,7 @@ static u8 bnx2x_8073_config_init(struct bnx2x_phy *phy, PORT_HW_CFG_SPEED_CAPABILITY_D0_10G) val |= (1<<7); - /* Note that 2.5G works only when - used with 1G advertisment */ + /* Note that 2.5G works only when used with 1G advertisment */ if (phy->speed_cap_mask & (PORT_HW_CFG_SPEED_CAPABILITY_D0_1G | PORT_HW_CFG_SPEED_CAPABILITY_D0_2_5G)) @@ -4211,9 +4191,11 @@ static u8 bnx2x_8073_config_init(struct bnx2x_phy *phy, /* Add support for CL37 (passive mode) III */ bnx2x_cl45_write(bp, phy, MDIO_AN_DEVAD, MDIO_AN_REG_CL37_AN, 0x1000); - /* The SNR will improve about 2db by changing - BW and FEE main tap. Rest commands are executed - after link is up*/ + /* + * The SNR will improve about 2db by changing BW and FEE main + * tap. Rest commands are executed after link is up + * Change FFE main cursor to 5 in EDC register + */ if (bnx2x_8073_is_snr_needed(bp, phy)) bnx2x_cl45_write(bp, phy, MDIO_PMA_DEVAD, MDIO_PMA_REG_EDC_FFE_MAIN, @@ -4297,12 +4279,11 @@ static u8 bnx2x_8073_read_status(struct bnx2x_phy *phy, link_up = (((val1 & 4) == 4) || (an1000_status & (1<<1))); if (link_up && bnx2x_8073_is_snr_needed(bp, phy)) { - /* The SNR will improve about 2dbby - changing the BW and FEE main tap.*/ - /* The 1st write to change FFE main - tap is set before restart AN */ - /* Change PLL Bandwidth in EDC - register */ + /* + * The SNR will improve about 2dbby changing the BW and FEE main + * tap. The 1st write to change FFE main tap is set before + * restart AN. Change PLL Bandwidth in EDC register + */ bnx2x_cl45_write(bp, phy, MDIO_PMA_DEVAD, MDIO_PMA_REG_PLL_BANDWIDTH, 0x26BC); @@ -4346,10 +4327,10 @@ static u8 bnx2x_8073_read_status(struct bnx2x_phy *phy, bnx2x_cl45_read(bp, phy, MDIO_XS_DEVAD, MDIO_XS_REG_8073_RX_CTRL_PCIE, &val1); - /** - * Set bit 3 to invert Rx in 1G mode and clear this bit - * when it`s in 10G mode. - */ + /* + * Set bit 3 to invert Rx in 1G mode and clear this bit + * when it`s in 10G mode. + */ if (vars->line_speed == SPEED_1000) { DP(NETIF_MSG_LINK, "Swapping 1G polarity for" "the 8073\n"); @@ -4381,8 +4362,8 @@ static void bnx2x_8073_link_reset(struct bnx2x_phy *phy, DP(NETIF_MSG_LINK, "Setting 8073 port %d into low power mode\n", gpio_port); bnx2x_set_gpio(bp, MISC_REGISTERS_GPIO_2, - MISC_REGISTERS_GPIO_OUTPUT_LOW, - gpio_port); + MISC_REGISTERS_GPIO_OUTPUT_LOW, + gpio_port); } /******************************************************************/ @@ -4396,11 +4377,11 @@ static u8 bnx2x_8705_config_init(struct bnx2x_phy *phy, DP(NETIF_MSG_LINK, "init 8705\n"); /* Restore normal power mode*/ bnx2x_set_gpio(bp, MISC_REGISTERS_GPIO_2, - MISC_REGISTERS_GPIO_OUTPUT_HIGH, params->port); + MISC_REGISTERS_GPIO_OUTPUT_HIGH, params->port); /* HW reset */ bnx2x_ext_phy_hw_reset(bp, params->port); bnx2x_cl45_write(bp, phy, MDIO_PMA_DEVAD, MDIO_PMA_REG_CTRL, 0xa040); - bnx2x_wait_reset_complete(bp, phy); + bnx2x_wait_reset_complete(bp, phy, params); bnx2x_cl45_write(bp, phy, MDIO_PMA_DEVAD, MDIO_PMA_REG_MISC_CTRL, 0x8288); @@ -4451,35 +4432,79 @@ static u8 bnx2x_8705_read_status(struct bnx2x_phy *phy, /******************************************************************/ /* SFP+ module Section */ /******************************************************************/ -static void bnx2x_sfp_set_transmitter(struct bnx2x *bp, +static u8 bnx2x_get_gpio_port(struct link_params *params) +{ + u8 gpio_port; + u32 swap_val, swap_override; + struct bnx2x *bp = params->bp; + if (CHIP_IS_E2(bp)) + gpio_port = BP_PATH(bp); + else + gpio_port = params->port; + swap_val = REG_RD(bp, NIG_REG_PORT_SWAP); + swap_override = REG_RD(bp, NIG_REG_STRAP_OVERRIDE); + return gpio_port ^ (swap_val && swap_override); +} +static void bnx2x_sfp_set_transmitter(struct link_params *params, struct bnx2x_phy *phy, - u8 port, u8 tx_en) { u16 val; + u8 port = params->port; + struct bnx2x *bp = params->bp; + u32 tx_en_mode; - DP(NETIF_MSG_LINK, "Setting transmitter tx_en=%x for port %x\n", - tx_en, port); /* Disable/Enable transmitter ( TX laser of the SFP+ module.)*/ - bnx2x_cl45_read(bp, phy, - MDIO_PMA_DEVAD, - MDIO_PMA_REG_PHY_IDENTIFIER, - &val); + tx_en_mode = REG_RD(bp, params->shmem_base + + offsetof(struct shmem_region, + dev_info.port_hw_config[port].sfp_ctrl)) & + PORT_HW_CFG_TX_LASER_MASK; + DP(NETIF_MSG_LINK, "Setting transmitter tx_en=%x for port %x " + "mode = %x\n", tx_en, port, tx_en_mode); + switch (tx_en_mode) { + case PORT_HW_CFG_TX_LASER_MDIO: - if (tx_en) - val &= ~(1<<15); - else - val |= (1<<15); + bnx2x_cl45_read(bp, phy, + MDIO_PMA_DEVAD, + MDIO_PMA_REG_PHY_IDENTIFIER, + &val); - bnx2x_cl45_write(bp, phy, - MDIO_PMA_DEVAD, - MDIO_PMA_REG_PHY_IDENTIFIER, - val); + if (tx_en) + val &= ~(1<<15); + else + val |= (1<<15); + + bnx2x_cl45_write(bp, phy, + MDIO_PMA_DEVAD, + MDIO_PMA_REG_PHY_IDENTIFIER, + val); + break; + case PORT_HW_CFG_TX_LASER_GPIO0: + case PORT_HW_CFG_TX_LASER_GPIO1: + case PORT_HW_CFG_TX_LASER_GPIO2: + case PORT_HW_CFG_TX_LASER_GPIO3: + { + u16 gpio_pin; + u8 gpio_port, gpio_mode; + if (tx_en) + gpio_mode = MISC_REGISTERS_GPIO_OUTPUT_HIGH; + else + gpio_mode = MISC_REGISTERS_GPIO_OUTPUT_LOW; + + gpio_pin = tx_en_mode - PORT_HW_CFG_TX_LASER_GPIO0; + gpio_port = bnx2x_get_gpio_port(params); + bnx2x_set_gpio(bp, gpio_pin, gpio_mode, gpio_port); + break; + } + default: + DP(NETIF_MSG_LINK, "Invalid TX_LASER_MDIO 0x%x\n", tx_en_mode); + break; + } } static u8 bnx2x_8726_read_sfp_module_eeprom(struct bnx2x_phy *phy, struct link_params *params, - u16 addr, u8 byte_cnt, u8 *o_buf) + u16 addr, u8 byte_cnt, u8 *o_buf) { struct bnx2x *bp = params->bp; u16 val = 0; @@ -4492,23 +4517,23 @@ static u8 bnx2x_8726_read_sfp_module_eeprom(struct bnx2x_phy *phy, /* Set the read command byte count */ bnx2x_cl45_write(bp, phy, MDIO_PMA_DEVAD, MDIO_PMA_REG_SFP_TWO_WIRE_BYTE_CNT, - (byte_cnt | 0xa000)); + (byte_cnt | 0xa000)); /* Set the read command address */ bnx2x_cl45_write(bp, phy, MDIO_PMA_DEVAD, MDIO_PMA_REG_SFP_TWO_WIRE_MEM_ADDR, - addr); + addr); /* Activate read command */ bnx2x_cl45_write(bp, phy, MDIO_PMA_DEVAD, MDIO_PMA_REG_SFP_TWO_WIRE_CTRL, - 0x2c0f); + 0x2c0f); /* Wait up to 500us for command complete status */ for (i = 0; i < 100; i++) { bnx2x_cl45_read(bp, phy, - MDIO_PMA_DEVAD, - MDIO_PMA_REG_SFP_TWO_WIRE_CTRL, &val); + MDIO_PMA_DEVAD, + MDIO_PMA_REG_SFP_TWO_WIRE_CTRL, &val); if ((val & MDIO_PMA_REG_SFP_TWO_WIRE_CTRL_STATUS_MASK) == MDIO_PMA_REG_SFP_TWO_WIRE_STATUS_COMPLETE) break; @@ -4526,15 +4551,15 @@ static u8 bnx2x_8726_read_sfp_module_eeprom(struct bnx2x_phy *phy, /* Read the buffer */ for (i = 0; i < byte_cnt; i++) { bnx2x_cl45_read(bp, phy, - MDIO_PMA_DEVAD, - MDIO_PMA_REG_8726_TWO_WIRE_DATA_BUF + i, &val); + MDIO_PMA_DEVAD, + MDIO_PMA_REG_8726_TWO_WIRE_DATA_BUF + i, &val); o_buf[i] = (u8)(val & MDIO_PMA_REG_8726_TWO_WIRE_DATA_MASK); } for (i = 0; i < 100; i++) { bnx2x_cl45_read(bp, phy, - MDIO_PMA_DEVAD, - MDIO_PMA_REG_SFP_TWO_WIRE_CTRL, &val); + MDIO_PMA_DEVAD, + MDIO_PMA_REG_SFP_TWO_WIRE_CTRL, &val); if ((val & MDIO_PMA_REG_SFP_TWO_WIRE_CTRL_STATUS_MASK) == MDIO_PMA_REG_SFP_TWO_WIRE_STATUS_IDLE) return 0; @@ -4545,7 +4570,7 @@ static u8 bnx2x_8726_read_sfp_module_eeprom(struct bnx2x_phy *phy, static u8 bnx2x_8727_read_sfp_module_eeprom(struct bnx2x_phy *phy, struct link_params *params, - u16 addr, u8 byte_cnt, u8 *o_buf) + u16 addr, u8 byte_cnt, u8 *o_buf) { struct bnx2x *bp = params->bp; u16 val, i; @@ -4558,41 +4583,43 @@ static u8 bnx2x_8727_read_sfp_module_eeprom(struct bnx2x_phy *phy, /* Need to read from 1.8000 to clear it */ bnx2x_cl45_read(bp, phy, - MDIO_PMA_DEVAD, - MDIO_PMA_REG_SFP_TWO_WIRE_CTRL, - &val); + MDIO_PMA_DEVAD, + MDIO_PMA_REG_SFP_TWO_WIRE_CTRL, + &val); /* Set the read command byte count */ bnx2x_cl45_write(bp, phy, - MDIO_PMA_DEVAD, - MDIO_PMA_REG_SFP_TWO_WIRE_BYTE_CNT, - ((byte_cnt < 2) ? 2 : byte_cnt)); + MDIO_PMA_DEVAD, + MDIO_PMA_REG_SFP_TWO_WIRE_BYTE_CNT, + ((byte_cnt < 2) ? 2 : byte_cnt)); /* Set the read command address */ bnx2x_cl45_write(bp, phy, - MDIO_PMA_DEVAD, - MDIO_PMA_REG_SFP_TWO_WIRE_MEM_ADDR, - addr); + MDIO_PMA_DEVAD, + MDIO_PMA_REG_SFP_TWO_WIRE_MEM_ADDR, + addr); /* Set the destination address */ bnx2x_cl45_write(bp, phy, - MDIO_PMA_DEVAD, - 0x8004, - MDIO_PMA_REG_8727_TWO_WIRE_DATA_BUF); + MDIO_PMA_DEVAD, + 0x8004, + MDIO_PMA_REG_8727_TWO_WIRE_DATA_BUF); /* Activate read command */ bnx2x_cl45_write(bp, phy, - MDIO_PMA_DEVAD, - MDIO_PMA_REG_SFP_TWO_WIRE_CTRL, - 0x8002); - /* Wait appropriate time for two-wire command to finish before - polling the status register */ + MDIO_PMA_DEVAD, + MDIO_PMA_REG_SFP_TWO_WIRE_CTRL, + 0x8002); + /* + * Wait appropriate time for two-wire command to finish before + * polling the status register + */ msleep(1); /* Wait up to 500us for command complete status */ for (i = 0; i < 100; i++) { bnx2x_cl45_read(bp, phy, - MDIO_PMA_DEVAD, - MDIO_PMA_REG_SFP_TWO_WIRE_CTRL, &val); + MDIO_PMA_DEVAD, + MDIO_PMA_REG_SFP_TWO_WIRE_CTRL, &val); if ((val & MDIO_PMA_REG_SFP_TWO_WIRE_CTRL_STATUS_MASK) == MDIO_PMA_REG_SFP_TWO_WIRE_STATUS_COMPLETE) break; @@ -4604,21 +4631,21 @@ static u8 bnx2x_8727_read_sfp_module_eeprom(struct bnx2x_phy *phy, DP(NETIF_MSG_LINK, "Got bad status 0x%x when reading from SFP+ EEPROM\n", (val & MDIO_PMA_REG_SFP_TWO_WIRE_CTRL_STATUS_MASK)); - return -EINVAL; + return -EFAULT; } /* Read the buffer */ for (i = 0; i < byte_cnt; i++) { bnx2x_cl45_read(bp, phy, - MDIO_PMA_DEVAD, - MDIO_PMA_REG_8727_TWO_WIRE_DATA_BUF + i, &val); + MDIO_PMA_DEVAD, + MDIO_PMA_REG_8727_TWO_WIRE_DATA_BUF + i, &val); o_buf[i] = (u8)(val & MDIO_PMA_REG_8727_TWO_WIRE_DATA_MASK); } for (i = 0; i < 100; i++) { bnx2x_cl45_read(bp, phy, - MDIO_PMA_DEVAD, - MDIO_PMA_REG_SFP_TWO_WIRE_CTRL, &val); + MDIO_PMA_DEVAD, + MDIO_PMA_REG_SFP_TWO_WIRE_CTRL, &val); if ((val & MDIO_PMA_REG_SFP_TWO_WIRE_CTRL_STATUS_MASK) == MDIO_PMA_REG_SFP_TWO_WIRE_STATUS_IDLE) return 0; @@ -4628,22 +4655,22 @@ static u8 bnx2x_8727_read_sfp_module_eeprom(struct bnx2x_phy *phy, return -EINVAL; } -static u8 bnx2x_read_sfp_module_eeprom(struct bnx2x_phy *phy, - struct link_params *params, u16 addr, - u8 byte_cnt, u8 *o_buf) +u8 bnx2x_read_sfp_module_eeprom(struct bnx2x_phy *phy, + struct link_params *params, u16 addr, + u8 byte_cnt, u8 *o_buf) { if (phy->type == PORT_HW_CFG_XGXS_EXT_PHY_TYPE_BCM8726) return bnx2x_8726_read_sfp_module_eeprom(phy, params, addr, - byte_cnt, o_buf); + byte_cnt, o_buf); else if (phy->type == PORT_HW_CFG_XGXS_EXT_PHY_TYPE_BCM8727) return bnx2x_8727_read_sfp_module_eeprom(phy, params, addr, - byte_cnt, o_buf); + byte_cnt, o_buf); return -EINVAL; } static u8 bnx2x_get_edc_mode(struct bnx2x_phy *phy, struct link_params *params, - u16 *edc_mode) + u16 *edc_mode) { struct bnx2x *bp = params->bp; u8 val, check_limiting_mode = 0; @@ -4664,8 +4691,10 @@ static u8 bnx2x_get_edc_mode(struct bnx2x_phy *phy, { u8 copper_module_type; - /* Check if its active cable( includes SFP+ module) - of passive cable*/ + /* + * Check if its active cable (includes SFP+ module) + * of passive cable + */ if (bnx2x_read_sfp_module_eeprom(phy, params, SFP_EEPROM_FC_TX_TECH_ADDR, @@ -4724,8 +4753,10 @@ static u8 bnx2x_get_edc_mode(struct bnx2x_phy *phy, DP(NETIF_MSG_LINK, "EDC mode is set to 0x%x\n", *edc_mode); return 0; } -/* This function read the relevant field from the module ( SFP+ ), - and verify it is compliant with this board */ +/* + * This function read the relevant field from the module (SFP+), and verify it + * is compliant with this board + */ static u8 bnx2x_verify_sfp_module(struct bnx2x_phy *phy, struct link_params *params) { @@ -4774,24 +4805,24 @@ static u8 bnx2x_verify_sfp_module(struct bnx2x_phy *phy, /* format the warning message */ if (bnx2x_read_sfp_module_eeprom(phy, params, - SFP_EEPROM_VENDOR_NAME_ADDR, - SFP_EEPROM_VENDOR_NAME_SIZE, - (u8 *)vendor_name)) + SFP_EEPROM_VENDOR_NAME_ADDR, + SFP_EEPROM_VENDOR_NAME_SIZE, + (u8 *)vendor_name)) vendor_name[0] = '\0'; else vendor_name[SFP_EEPROM_VENDOR_NAME_SIZE] = '\0'; if (bnx2x_read_sfp_module_eeprom(phy, params, - SFP_EEPROM_PART_NO_ADDR, - SFP_EEPROM_PART_NO_SIZE, - (u8 *)vendor_pn)) + SFP_EEPROM_PART_NO_ADDR, + SFP_EEPROM_PART_NO_SIZE, + (u8 *)vendor_pn)) vendor_pn[0] = '\0'; else vendor_pn[SFP_EEPROM_PART_NO_SIZE] = '\0'; - netdev_info(bp->dev, "Warning: Unqualified SFP+ module detected," - " Port %d from %s part number %s\n", - params->port, vendor_name, vendor_pn); + netdev_err(bp->dev, "Warning: Unqualified SFP+ module detected," + " Port %d from %s part number %s\n", + params->port, vendor_name, vendor_pn); phy->flags |= FLAGS_SFP_NOT_APPROVED; return -EINVAL; } @@ -4803,8 +4834,11 @@ static u8 bnx2x_wait_for_sfp_module_initialized(struct bnx2x_phy *phy, u8 val; struct bnx2x *bp = params->bp; u16 timeout; - /* Initialization time after hot-plug may take up to 300ms for some - phys type ( e.g. JDSU ) */ + /* + * Initialization time after hot-plug may take up to 300ms for + * some phys type ( e.g. JDSU ) + */ + for (timeout = 0; timeout < 60; timeout++) { if (bnx2x_read_sfp_module_eeprom(phy, params, 1, 1, &val) == 0) { @@ -4823,16 +4857,14 @@ static void bnx2x_8727_power_module(struct bnx2x *bp, /* Make sure GPIOs are not using for LED mode */ u16 val; /* - * In the GPIO register, bit 4 is use to detemine if the GPIOs are + * In the GPIO register, bit 4 is use to determine if the GPIOs are * operating as INPUT or as OUTPUT. Bit 1 is for input, and 0 for * output * Bits 0-1 determine the gpios value for OUTPUT in case bit 4 val is 0 * Bits 8-9 determine the gpios value for INPUT in case bit 4 val is 1 * where the 1st bit is the over-current(only input), and 2nd bit is * for power( only output ) - */ - - /* + * * In case of NOC feature is disabled and power is up, set GPIO control * as input to enable listening of over-current indication */ @@ -4861,15 +4893,14 @@ static u8 bnx2x_8726_set_limiting_mode(struct bnx2x *bp, u16 cur_limiting_mode; bnx2x_cl45_read(bp, phy, - MDIO_PMA_DEVAD, - MDIO_PMA_REG_ROM_VER2, - &cur_limiting_mode); + MDIO_PMA_DEVAD, + MDIO_PMA_REG_ROM_VER2, + &cur_limiting_mode); DP(NETIF_MSG_LINK, "Current Limiting mode is 0x%x\n", cur_limiting_mode); if (edc_mode == EDC_MODE_LIMITING) { - DP(NETIF_MSG_LINK, - "Setting LIMITING MODE\n"); + DP(NETIF_MSG_LINK, "Setting LIMITING MODE\n"); bnx2x_cl45_write(bp, phy, MDIO_PMA_DEVAD, MDIO_PMA_REG_ROM_VER2, @@ -4878,62 +4909,63 @@ static u8 bnx2x_8726_set_limiting_mode(struct bnx2x *bp, DP(NETIF_MSG_LINK, "Setting LRM MODE\n"); - /* Changing to LRM mode takes quite few seconds. - So do it only if current mode is limiting - ( default is LRM )*/ + /* + * Changing to LRM mode takes quite few seconds. So do it only + * if current mode is limiting (default is LRM) + */ if (cur_limiting_mode != EDC_MODE_LIMITING) return 0; bnx2x_cl45_write(bp, phy, - MDIO_PMA_DEVAD, - MDIO_PMA_REG_LRM_MODE, - 0); + MDIO_PMA_DEVAD, + MDIO_PMA_REG_LRM_MODE, + 0); bnx2x_cl45_write(bp, phy, - MDIO_PMA_DEVAD, - MDIO_PMA_REG_ROM_VER2, - 0x128); + MDIO_PMA_DEVAD, + MDIO_PMA_REG_ROM_VER2, + 0x128); bnx2x_cl45_write(bp, phy, - MDIO_PMA_DEVAD, - MDIO_PMA_REG_MISC_CTRL0, - 0x4008); + MDIO_PMA_DEVAD, + MDIO_PMA_REG_MISC_CTRL0, + 0x4008); bnx2x_cl45_write(bp, phy, - MDIO_PMA_DEVAD, - MDIO_PMA_REG_LRM_MODE, - 0xaaaa); + MDIO_PMA_DEVAD, + MDIO_PMA_REG_LRM_MODE, + 0xaaaa); } return 0; } static u8 bnx2x_8727_set_limiting_mode(struct bnx2x *bp, struct bnx2x_phy *phy, - u16 edc_mode) + u16 edc_mode) { u16 phy_identifier; u16 rom_ver2_val; bnx2x_cl45_read(bp, phy, - MDIO_PMA_DEVAD, - MDIO_PMA_REG_PHY_IDENTIFIER, - &phy_identifier); + MDIO_PMA_DEVAD, + MDIO_PMA_REG_PHY_IDENTIFIER, + &phy_identifier); bnx2x_cl45_write(bp, phy, - MDIO_PMA_DEVAD, - MDIO_PMA_REG_PHY_IDENTIFIER, - (phy_identifier & ~(1<<9))); + MDIO_PMA_DEVAD, + MDIO_PMA_REG_PHY_IDENTIFIER, + (phy_identifier & ~(1<<9))); bnx2x_cl45_read(bp, phy, - MDIO_PMA_DEVAD, - MDIO_PMA_REG_ROM_VER2, - &rom_ver2_val); + MDIO_PMA_DEVAD, + MDIO_PMA_REG_ROM_VER2, + &rom_ver2_val); /* Keep the MSB 8-bits, and set the LSB 8-bits with the edc_mode */ bnx2x_cl45_write(bp, phy, - MDIO_PMA_DEVAD, - MDIO_PMA_REG_ROM_VER2, - (rom_ver2_val & 0xff00) | (edc_mode & 0x00ff)); + MDIO_PMA_DEVAD, + MDIO_PMA_REG_ROM_VER2, + (rom_ver2_val & 0xff00) | (edc_mode & 0x00ff)); bnx2x_cl45_write(bp, phy, - MDIO_PMA_DEVAD, - MDIO_PMA_REG_PHY_IDENTIFIER, - (phy_identifier | (1<<9))); + MDIO_PMA_DEVAD, + MDIO_PMA_REG_PHY_IDENTIFIER, + (phy_identifier | (1<<9))); return 0; } @@ -4946,11 +4978,11 @@ static void bnx2x_8727_specific_func(struct bnx2x_phy *phy, switch (action) { case DISABLE_TX: - bnx2x_sfp_set_transmitter(bp, phy, params->port, 0); + bnx2x_sfp_set_transmitter(params, phy, 0); break; case ENABLE_TX: if (!(phy->flags & FLAGS_SFP_NOT_APPROVED)) - bnx2x_sfp_set_transmitter(bp, phy, params->port, 1); + bnx2x_sfp_set_transmitter(params, phy, 1); break; default: DP(NETIF_MSG_LINK, "Function 0x%x not supported by 8727\n", @@ -4959,6 +4991,38 @@ static void bnx2x_8727_specific_func(struct bnx2x_phy *phy, } } +static void bnx2x_set_sfp_module_fault_led(struct link_params *params, + u8 gpio_mode) +{ + struct bnx2x *bp = params->bp; + + u32 fault_led_gpio = REG_RD(bp, params->shmem_base + + offsetof(struct shmem_region, + dev_info.port_hw_config[params->port].sfp_ctrl)) & + PORT_HW_CFG_FAULT_MODULE_LED_MASK; + switch (fault_led_gpio) { + case PORT_HW_CFG_FAULT_MODULE_LED_DISABLED: + return; + case PORT_HW_CFG_FAULT_MODULE_LED_GPIO0: + case PORT_HW_CFG_FAULT_MODULE_LED_GPIO1: + case PORT_HW_CFG_FAULT_MODULE_LED_GPIO2: + case PORT_HW_CFG_FAULT_MODULE_LED_GPIO3: + { + u8 gpio_port = bnx2x_get_gpio_port(params); + u16 gpio_pin = fault_led_gpio - + PORT_HW_CFG_FAULT_MODULE_LED_GPIO0; + DP(NETIF_MSG_LINK, "Set fault module-detected led " + "pin %x port %x mode %x\n", + gpio_pin, gpio_port, gpio_mode); + bnx2x_set_gpio(bp, gpio_pin, gpio_mode, gpio_port); + } + break; + default: + DP(NETIF_MSG_LINK, "Error: Invalid fault led mode 0x%x\n", + fault_led_gpio); + } +} + static u8 bnx2x_sfp_module_detection(struct bnx2x_phy *phy, struct link_params *params) { @@ -4976,15 +5040,14 @@ static u8 bnx2x_sfp_module_detection(struct bnx2x_phy *phy, if (bnx2x_get_edc_mode(phy, params, &edc_mode) != 0) { DP(NETIF_MSG_LINK, "Failed to get valid module type\n"); return -EINVAL; - } else if (bnx2x_verify_sfp_module(phy, params) != - 0) { + } else if (bnx2x_verify_sfp_module(phy, params) != 0) { /* check SFP+ module compatibility */ DP(NETIF_MSG_LINK, "Module verification failed!!\n"); rc = -EINVAL; /* Turn on fault module-detected led */ - bnx2x_set_gpio(bp, MISC_REGISTERS_GPIO_0, - MISC_REGISTERS_GPIO_HIGH, - params->port); + bnx2x_set_sfp_module_fault_led(params, + MISC_REGISTERS_GPIO_HIGH); + if ((phy->type == PORT_HW_CFG_XGXS_EXT_PHY_TYPE_BCM8727) && ((val & PORT_FEAT_CFG_OPT_MDL_ENFRCMNT_MASK) == PORT_FEAT_CFG_OPT_MDL_ENFRCMNT_POWER_DOWN)) { @@ -4995,18 +5058,17 @@ static u8 bnx2x_sfp_module_detection(struct bnx2x_phy *phy, } } else { /* Turn off fault module-detected led */ - DP(NETIF_MSG_LINK, "Turn off fault module-detected led\n"); - bnx2x_set_gpio(bp, MISC_REGISTERS_GPIO_0, - MISC_REGISTERS_GPIO_LOW, - params->port); + bnx2x_set_sfp_module_fault_led(params, MISC_REGISTERS_GPIO_LOW); } /* power up the SFP module */ if (phy->type == PORT_HW_CFG_XGXS_EXT_PHY_TYPE_BCM8727) bnx2x_8727_power_module(bp, phy, 1); - /* Check and set limiting mode / LRM mode on 8726. - On 8727 it is done automatically */ + /* + * Check and set limiting mode / LRM mode on 8726. On 8727 it + * is done automatically + */ if (phy->type == PORT_HW_CFG_XGXS_EXT_PHY_TYPE_BCM8726) bnx2x_8726_set_limiting_mode(bp, phy, edc_mode); else @@ -5018,9 +5080,9 @@ static u8 bnx2x_sfp_module_detection(struct bnx2x_phy *phy, if (rc == 0 || (val & PORT_FEAT_CFG_OPT_MDL_ENFRCMNT_MASK) != PORT_FEAT_CFG_OPT_MDL_ENFRCMNT_DISABLE_TX_LASER) - bnx2x_sfp_set_transmitter(bp, phy, params->port, 1); + bnx2x_sfp_set_transmitter(params, phy, 1); else - bnx2x_sfp_set_transmitter(bp, phy, params->port, 0); + bnx2x_sfp_set_transmitter(params, phy, 0); return rc; } @@ -5033,11 +5095,9 @@ void bnx2x_handle_module_detect_int(struct link_params *params) u8 port = params->port; /* Set valid module led off */ - bnx2x_set_gpio(bp, MISC_REGISTERS_GPIO_0, - MISC_REGISTERS_GPIO_HIGH, - params->port); + bnx2x_set_sfp_module_fault_led(params, MISC_REGISTERS_GPIO_HIGH); - /* Get current gpio val refelecting module plugged in / out*/ + /* Get current gpio val reflecting module plugged in / out*/ gpio_val = bnx2x_get_gpio(bp, MISC_REGISTERS_GPIO_3, port); /* Call the handling function in case module is detected */ @@ -5053,18 +5113,20 @@ void bnx2x_handle_module_detect_int(struct link_params *params) DP(NETIF_MSG_LINK, "SFP+ module is not initialized\n"); } else { u32 val = REG_RD(bp, params->shmem_base + - offsetof(struct shmem_region, dev_info. - port_feature_config[params->port]. - config)); + offsetof(struct shmem_region, dev_info. + port_feature_config[params->port]. + config)); bnx2x_set_gpio_int(bp, MISC_REGISTERS_GPIO_3, MISC_REGISTERS_GPIO_INT_OUTPUT_SET, port); - /* Module was plugged out. */ - /* Disable transmit for this module */ + /* + * Module was plugged out. + * Disable transmit for this module + */ if ((val & PORT_FEAT_CFG_OPT_MDL_ENFRCMNT_MASK) == PORT_FEAT_CFG_OPT_MDL_ENFRCMNT_DISABLE_TX_LASER) - bnx2x_sfp_set_transmitter(bp, phy, params->port, 0); + bnx2x_sfp_set_transmitter(params, phy, 0); } } @@ -5100,9 +5162,9 @@ static u8 bnx2x_8706_8726_read_status(struct bnx2x_phy *phy, DP(NETIF_MSG_LINK, "8706/8726 rx_sd 0x%x pcs_status 0x%x 1Gbps" " link_status 0x%x\n", rx_sd, pcs_status, val2); - /* link is up if both bit 0 of pmd_rx_sd and - * bit 0 of pcs_status are set, or if the autoneg bit - * 1 is set + /* + * link is up if both bit 0 of pmd_rx_sd and bit 0 of pcs_status + * are set, or if the autoneg bit 1 is set */ link_up = ((rx_sd & pcs_status & 0x1) || (val2 & (1<<1))); if (link_up) { @@ -5123,14 +5185,15 @@ static u8 bnx2x_8706_config_init(struct bnx2x_phy *phy, struct link_params *params, struct link_vars *vars) { - u16 cnt, val; + u32 tx_en_mode; + u16 cnt, val, tmp1; struct bnx2x *bp = params->bp; bnx2x_set_gpio(bp, MISC_REGISTERS_GPIO_2, - MISC_REGISTERS_GPIO_OUTPUT_HIGH, params->port); + MISC_REGISTERS_GPIO_OUTPUT_HIGH, params->port); /* HW reset */ bnx2x_ext_phy_hw_reset(bp, params->port); bnx2x_cl45_write(bp, phy, MDIO_PMA_DEVAD, MDIO_PMA_REG_CTRL, 0xa040); - bnx2x_wait_reset_complete(bp, phy); + bnx2x_wait_reset_complete(bp, phy, params); /* Wait until fw is loaded */ for (cnt = 0; cnt < 100; cnt++) { @@ -5197,6 +5260,26 @@ static u8 bnx2x_8706_config_init(struct bnx2x_phy *phy, 0x0004); } bnx2x_save_bcm_spirom_ver(bp, phy, params->port); + + /* + * If TX Laser is controlled by GPIO_0, do not let PHY go into low + * power mode, if TX Laser is disabled + */ + + tx_en_mode = REG_RD(bp, params->shmem_base + + offsetof(struct shmem_region, + dev_info.port_hw_config[params->port].sfp_ctrl)) + & PORT_HW_CFG_TX_LASER_MASK; + + if (tx_en_mode == PORT_HW_CFG_TX_LASER_GPIO0) { + DP(NETIF_MSG_LINK, "Enabling TXONOFF_PWRDN_DIS\n"); + bnx2x_cl45_read(bp, phy, + MDIO_PMA_DEVAD, MDIO_PMA_REG_DIGITAL_CTRL, &tmp1); + tmp1 |= 0x1; + bnx2x_cl45_write(bp, phy, + MDIO_PMA_DEVAD, MDIO_PMA_REG_DIGITAL_CTRL, tmp1); + } + return 0; } @@ -5231,26 +5314,26 @@ static void bnx2x_8726_external_rom_boot(struct bnx2x_phy *phy, /* Set soft reset */ bnx2x_cl45_write(bp, phy, - MDIO_PMA_DEVAD, - MDIO_PMA_REG_GEN_CTRL, - MDIO_PMA_REG_GEN_CTRL_ROM_MICRO_RESET); + MDIO_PMA_DEVAD, + MDIO_PMA_REG_GEN_CTRL, + MDIO_PMA_REG_GEN_CTRL_ROM_MICRO_RESET); bnx2x_cl45_write(bp, phy, - MDIO_PMA_DEVAD, - MDIO_PMA_REG_MISC_CTRL1, 0x0001); + MDIO_PMA_DEVAD, + MDIO_PMA_REG_MISC_CTRL1, 0x0001); bnx2x_cl45_write(bp, phy, - MDIO_PMA_DEVAD, - MDIO_PMA_REG_GEN_CTRL, - MDIO_PMA_REG_GEN_CTRL_ROM_RESET_INTERNAL_MP); + MDIO_PMA_DEVAD, + MDIO_PMA_REG_GEN_CTRL, + MDIO_PMA_REG_GEN_CTRL_ROM_RESET_INTERNAL_MP); /* wait for 150ms for microcode load */ msleep(150); /* Disable serial boot control, tristates pins SS_N, SCK, MOSI, MISO */ bnx2x_cl45_write(bp, phy, - MDIO_PMA_DEVAD, - MDIO_PMA_REG_MISC_CTRL1, 0x0000); + MDIO_PMA_DEVAD, + MDIO_PMA_REG_MISC_CTRL1, 0x0000); msleep(200); bnx2x_save_bcm_spirom_ver(bp, phy, params->port); @@ -5285,23 +5368,18 @@ static u8 bnx2x_8726_config_init(struct bnx2x_phy *phy, u32 val; u32 swap_val, swap_override, aeu_gpio_mask, offset; DP(NETIF_MSG_LINK, "Initializing BCM8726\n"); - /* Restore normal power mode*/ - bnx2x_set_gpio(bp, MISC_REGISTERS_GPIO_2, - MISC_REGISTERS_GPIO_OUTPUT_HIGH, params->port); - - bnx2x_set_gpio(bp, MISC_REGISTERS_GPIO_1, - MISC_REGISTERS_GPIO_OUTPUT_HIGH, params->port); bnx2x_cl45_write(bp, phy, MDIO_PMA_DEVAD, MDIO_PMA_REG_CTRL, 1<<15); - bnx2x_wait_reset_complete(bp, phy); + bnx2x_wait_reset_complete(bp, phy, params); bnx2x_8726_external_rom_boot(phy, params); - /* Need to call module detected on initialization since - the module detection triggered by actual module - insertion might occur before driver is loaded, and when - driver is loaded, it reset all registers, including the - transmitter */ + /* + * Need to call module detected on initialization since the module + * detection triggered by actual module insertion might occur before + * driver is loaded, and when driver is loaded, it reset all + * registers, including the transmitter + */ bnx2x_sfp_module_detection(phy, params); if (phy->req_line_speed == SPEED_1000) { @@ -5334,8 +5412,10 @@ static u8 bnx2x_8726_config_init(struct bnx2x_phy *phy, MDIO_AN_DEVAD, MDIO_AN_REG_CL37_AN, 0x1000); bnx2x_cl45_write(bp, phy, MDIO_AN_DEVAD, MDIO_AN_REG_CTRL, 0x1200); - /* Enable RX-ALARM control to receive - interrupt for 1G speed change */ + /* + * Enable RX-ALARM control to receive interrupt for 1G speed + * change + */ bnx2x_cl45_write(bp, phy, MDIO_PMA_DEVAD, MDIO_PMA_REG_LASI_CTRL, 0x4); bnx2x_cl45_write(bp, phy, @@ -5367,7 +5447,7 @@ static u8 bnx2x_8726_config_init(struct bnx2x_phy *phy, /* Set GPIO3 to trigger SFP+ module insertion/removal */ bnx2x_set_gpio(bp, MISC_REGISTERS_GPIO_3, - MISC_REGISTERS_GPIO_INPUT_HI_Z, params->port); + MISC_REGISTERS_GPIO_INPUT_HI_Z, params->port); /* The GPIO should be swapped if the swap register is set and active */ swap_val = REG_RD(bp, NIG_REG_PORT_SWAP); @@ -5458,7 +5538,7 @@ static void bnx2x_8727_hw_reset(struct bnx2x_phy *phy, struct link_params *params) { u32 swap_val, swap_override; u8 port; - /** + /* * The PHY reset is controlled by GPIO 1. Fake the port number * to cancel the swap done in set_gpio() */ @@ -5467,20 +5547,21 @@ static void bnx2x_8727_hw_reset(struct bnx2x_phy *phy, swap_override = REG_RD(bp, NIG_REG_STRAP_OVERRIDE); port = (swap_val && swap_override) ^ 1; bnx2x_set_gpio(bp, MISC_REGISTERS_GPIO_1, - MISC_REGISTERS_GPIO_OUTPUT_LOW, port); + MISC_REGISTERS_GPIO_OUTPUT_LOW, port); } static u8 bnx2x_8727_config_init(struct bnx2x_phy *phy, struct link_params *params, struct link_vars *vars) { - u16 tmp1, val, mod_abs; + u32 tx_en_mode; + u16 tmp1, val, mod_abs, tmp2; u16 rx_alarm_ctrl_val; u16 lasi_ctrl_val; struct bnx2x *bp = params->bp; /* Enable PMD link, MOD_ABS_FLT, and 1G link alarm */ - bnx2x_wait_reset_complete(bp, phy); + bnx2x_wait_reset_complete(bp, phy, params); rx_alarm_ctrl_val = (1<<2) | (1<<5) ; lasi_ctrl_val = 0x0004; @@ -5493,14 +5574,17 @@ static u8 bnx2x_8727_config_init(struct bnx2x_phy *phy, bnx2x_cl45_write(bp, phy, MDIO_PMA_DEVAD, MDIO_PMA_REG_LASI_CTRL, lasi_ctrl_val); - /* Initially configure MOD_ABS to interrupt when - module is presence( bit 8) */ + /* + * Initially configure MOD_ABS to interrupt when module is + * presence( bit 8) + */ bnx2x_cl45_read(bp, phy, MDIO_PMA_DEVAD, MDIO_PMA_REG_PHY_IDENTIFIER, &mod_abs); - /* Set EDC off by setting OPTXLOS signal input to low - (bit 9). - When the EDC is off it locks onto a reference clock and - avoids becoming 'lost'.*/ + /* + * Set EDC off by setting OPTXLOS signal input to low (bit 9). + * When the EDC is off it locks onto a reference clock and avoids + * becoming 'lost' + */ mod_abs &= ~(1<<8); if (!(phy->flags & FLAGS_NOC)) mod_abs &= ~(1<<9); @@ -5515,7 +5599,7 @@ static u8 bnx2x_8727_config_init(struct bnx2x_phy *phy, if (phy->flags & FLAGS_NOC) val |= (3<<5); - /** + /* * Set 8727 GPIOs to input to allow reading from the 8727 GPIO0 * status which reflect SFP+ module over-current */ @@ -5542,7 +5626,7 @@ static u8 bnx2x_8727_config_init(struct bnx2x_phy *phy, bnx2x_cl45_read(bp, phy, MDIO_PMA_DEVAD, MDIO_PMA_REG_10G_CTRL2, &tmp1); DP(NETIF_MSG_LINK, "1.7 = 0x%x\n", tmp1); - /** + /* * Power down the XAUI until link is up in case of dual-media * and 1G */ @@ -5568,7 +5652,7 @@ static u8 bnx2x_8727_config_init(struct bnx2x_phy *phy, bnx2x_cl45_write(bp, phy, MDIO_AN_DEVAD, MDIO_AN_REG_CL37_AN, 0x1300); } else { - /** + /* * Since the 8727 has only single reset pin, need to set the 10G * registers although it is default */ @@ -5584,7 +5668,8 @@ static u8 bnx2x_8727_config_init(struct bnx2x_phy *phy, 0x0008); } - /* Set 2-wire transfer rate of SFP+ module EEPROM + /* + * Set 2-wire transfer rate of SFP+ module EEPROM * to 100Khz since some DACs(direct attached cables) do * not work at 400Khz. */ @@ -5607,6 +5692,26 @@ static u8 bnx2x_8727_config_init(struct bnx2x_phy *phy, phy->tx_preemphasis[1]); } + /* + * If TX Laser is controlled by GPIO_0, do not let PHY go into low + * power mode, if TX Laser is disabled + */ + tx_en_mode = REG_RD(bp, params->shmem_base + + offsetof(struct shmem_region, + dev_info.port_hw_config[params->port].sfp_ctrl)) + & PORT_HW_CFG_TX_LASER_MASK; + + if (tx_en_mode == PORT_HW_CFG_TX_LASER_GPIO0) { + + DP(NETIF_MSG_LINK, "Enabling TXONOFF_PWRDN_DIS\n"); + bnx2x_cl45_read(bp, phy, + MDIO_PMA_DEVAD, MDIO_PMA_REG_8727_OPT_CFG_REG, &tmp2); + tmp2 |= 0x1000; + tmp2 &= 0xFFEF; + bnx2x_cl45_write(bp, phy, + MDIO_PMA_DEVAD, MDIO_PMA_REG_8727_OPT_CFG_REG, tmp2); + } + return 0; } @@ -5620,46 +5725,49 @@ static void bnx2x_8727_handle_mod_abs(struct bnx2x_phy *phy, port_feature_config[params->port]. config)); bnx2x_cl45_read(bp, phy, - MDIO_PMA_DEVAD, - MDIO_PMA_REG_PHY_IDENTIFIER, &mod_abs); + MDIO_PMA_DEVAD, + MDIO_PMA_REG_PHY_IDENTIFIER, &mod_abs); if (mod_abs & (1<<8)) { /* Module is absent */ DP(NETIF_MSG_LINK, "MOD_ABS indication " "show module is absent\n"); - /* 1. Set mod_abs to detect next module - presence event - 2. Set EDC off by setting OPTXLOS signal input to low - (bit 9). - When the EDC is off it locks onto a reference clock and - avoids becoming 'lost'.*/ + /* + * 1. Set mod_abs to detect next module + * presence event + * 2. Set EDC off by setting OPTXLOS signal input to low + * (bit 9). + * When the EDC is off it locks onto a reference clock and + * avoids becoming 'lost'. + */ mod_abs &= ~(1<<8); if (!(phy->flags & FLAGS_NOC)) mod_abs &= ~(1<<9); bnx2x_cl45_write(bp, phy, - MDIO_PMA_DEVAD, - MDIO_PMA_REG_PHY_IDENTIFIER, mod_abs); + MDIO_PMA_DEVAD, + MDIO_PMA_REG_PHY_IDENTIFIER, mod_abs); - /* Clear RX alarm since it stays up as long as - the mod_abs wasn't changed */ + /* + * Clear RX alarm since it stays up as long as + * the mod_abs wasn't changed + */ bnx2x_cl45_read(bp, phy, - MDIO_PMA_DEVAD, - MDIO_PMA_REG_RX_ALARM, &rx_alarm_status); + MDIO_PMA_DEVAD, + MDIO_PMA_REG_RX_ALARM, &rx_alarm_status); } else { /* Module is present */ DP(NETIF_MSG_LINK, "MOD_ABS indication " "show module is present\n"); - /* First thing, disable transmitter, - and if the module is ok, the - module_detection will enable it*/ - - /* 1. Set mod_abs to detect next module - absent event ( bit 8) - 2. Restore the default polarity of the OPRXLOS signal and - this signal will then correctly indicate the presence or - absence of the Rx signal. (bit 9) */ + /* + * First disable transmitter, and if the module is ok, the + * module_detection will enable it + * 1. Set mod_abs to detect next module absent event ( bit 8) + * 2. Restore the default polarity of the OPRXLOS signal and + * this signal will then correctly indicate the presence or + * absence of the Rx signal. (bit 9) + */ mod_abs |= (1<<8); if (!(phy->flags & FLAGS_NOC)) mod_abs |= (1<<9); @@ -5667,10 +5775,12 @@ static void bnx2x_8727_handle_mod_abs(struct bnx2x_phy *phy, MDIO_PMA_DEVAD, MDIO_PMA_REG_PHY_IDENTIFIER, mod_abs); - /* Clear RX alarm since it stays up as long as - the mod_abs wasn't changed. This is need to be done - before calling the module detection, otherwise it will clear - the link update alarm */ + /* + * Clear RX alarm since it stays up as long as the mod_abs + * wasn't changed. This is need to be done before calling the + * module detection, otherwise it will clear* the link update + * alarm + */ bnx2x_cl45_read(bp, phy, MDIO_PMA_DEVAD, MDIO_PMA_REG_RX_ALARM, &rx_alarm_status); @@ -5678,7 +5788,7 @@ static void bnx2x_8727_handle_mod_abs(struct bnx2x_phy *phy, if ((val & PORT_FEAT_CFG_OPT_MDL_ENFRCMNT_MASK) == PORT_FEAT_CFG_OPT_MDL_ENFRCMNT_DISABLE_TX_LASER) - bnx2x_sfp_set_transmitter(bp, phy, params->port, 0); + bnx2x_sfp_set_transmitter(params, phy, 0); if (bnx2x_wait_for_sfp_module_initialized(phy, params) == 0) bnx2x_sfp_module_detection(phy, params); @@ -5687,9 +5797,8 @@ static void bnx2x_8727_handle_mod_abs(struct bnx2x_phy *phy, } DP(NETIF_MSG_LINK, "8727 RX_ALARM_STATUS 0x%x\n", - rx_alarm_status); - /* No need to check link status in case of - module plugged in/out */ + rx_alarm_status); + /* No need to check link status in case of module plugged in/out */ } static u8 bnx2x_8727_read_status(struct bnx2x_phy *phy, @@ -5725,7 +5834,7 @@ static u8 bnx2x_8727_read_status(struct bnx2x_phy *phy, bnx2x_cl45_read(bp, phy, MDIO_PMA_DEVAD, MDIO_PMA_REG_M8051_MSGOUT_REG, &val1); - /** + /* * If a module is present and there is need to check * for over current */ @@ -5745,12 +5854,8 @@ static u8 bnx2x_8727_read_status(struct bnx2x_phy *phy, " Please remove the SFP+ module and" " restart the system to clear this" " error.\n", - params->port); - - /* - * Disable all RX_ALARMs except for - * mod_abs - */ + params->port); + /* Disable all RX_ALARMs except for mod_abs */ bnx2x_cl45_write(bp, phy, MDIO_PMA_DEVAD, MDIO_PMA_REG_RX_ALARM_CTRL, (1<<5)); @@ -5793,11 +5898,15 @@ static u8 bnx2x_8727_read_status(struct bnx2x_phy *phy, MDIO_PMA_DEVAD, MDIO_PMA_REG_8073_SPEED_LINK_STATUS, &link_status); - /* Bits 0..2 --> speed detected, - bits 13..15--> link is down */ + /* + * Bits 0..2 --> speed detected, + * Bits 13..15--> link is down + */ if ((link_status & (1<<2)) && (!(link_status & (1<<15)))) { link_up = 1; vars->line_speed = SPEED_10000; + DP(NETIF_MSG_LINK, "port %x: External link up in 10G\n", + params->port); } else if ((link_status & (1<<0)) && (!(link_status & (1<<13)))) { link_up = 1; vars->line_speed = SPEED_1000; @@ -5819,7 +5928,7 @@ static u8 bnx2x_8727_read_status(struct bnx2x_phy *phy, bnx2x_cl45_read(bp, phy, MDIO_PMA_DEVAD, MDIO_PMA_REG_8727_PCS_GP, &val1); - /** + /* * In case of dual-media board and 1G, power up the XAUI side, * otherwise power it down. For 10G it is done automatically */ @@ -5839,7 +5948,7 @@ static void bnx2x_8727_link_reset(struct bnx2x_phy *phy, { struct bnx2x *bp = params->bp; /* Disable Transmitter */ - bnx2x_sfp_set_transmitter(bp, phy, params->port, 0); + bnx2x_sfp_set_transmitter(params, phy, 0); /* Clear LASI */ bnx2x_cl45_write(bp, phy, MDIO_PMA_DEVAD, MDIO_PMA_REG_LASI_CTRL, 0); @@ -5851,19 +5960,23 @@ static void bnx2x_8727_link_reset(struct bnx2x_phy *phy, static void bnx2x_save_848xx_spirom_version(struct bnx2x_phy *phy, struct link_params *params) { - u16 val, fw_ver1, fw_ver2, cnt; + u16 val, fw_ver1, fw_ver2, cnt, adj; struct bnx2x *bp = params->bp; + adj = 0; + if (phy->type == PORT_HW_CFG_XGXS_EXT_PHY_TYPE_BCM84833) + adj = -1; + /* For the 32 bits registers in 848xx, access via MDIO2ARM interface.*/ /* (1) set register 0xc200_0014(SPI_BRIDGE_CTRL_2) to 0x03000000 */ - bnx2x_cl45_write(bp, phy, MDIO_PMA_DEVAD, 0xA819, 0x0014); - bnx2x_cl45_write(bp, phy, MDIO_PMA_DEVAD, 0xA81A, 0xc200); - bnx2x_cl45_write(bp, phy, MDIO_PMA_DEVAD, 0xA81B, 0x0000); - bnx2x_cl45_write(bp, phy, MDIO_PMA_DEVAD, 0xA81C, 0x0300); - bnx2x_cl45_write(bp, phy, MDIO_PMA_DEVAD, 0xA817, 0x0009); + bnx2x_cl45_write(bp, phy, MDIO_PMA_DEVAD, 0xA819 + adj, 0x0014); + bnx2x_cl45_write(bp, phy, MDIO_PMA_DEVAD, 0xA81A + adj, 0xc200); + bnx2x_cl45_write(bp, phy, MDIO_PMA_DEVAD, 0xA81B + adj, 0x0000); + bnx2x_cl45_write(bp, phy, MDIO_PMA_DEVAD, 0xA81C + adj, 0x0300); + bnx2x_cl45_write(bp, phy, MDIO_PMA_DEVAD, 0xA817 + adj, 0x0009); for (cnt = 0; cnt < 100; cnt++) { - bnx2x_cl45_read(bp, phy, MDIO_PMA_DEVAD, 0xA818, &val); + bnx2x_cl45_read(bp, phy, MDIO_PMA_DEVAD, 0xA818 + adj, &val); if (val & 1) break; udelay(5); @@ -5877,11 +5990,11 @@ static void bnx2x_save_848xx_spirom_version(struct bnx2x_phy *phy, /* 2) read register 0xc200_0000 (SPI_FW_STATUS) */ - bnx2x_cl45_write(bp, phy, MDIO_PMA_DEVAD, 0xA819, 0x0000); - bnx2x_cl45_write(bp, phy, MDIO_PMA_DEVAD, 0xA81A, 0xc200); - bnx2x_cl45_write(bp, phy, MDIO_PMA_DEVAD, 0xA817, 0x000A); + bnx2x_cl45_write(bp, phy, MDIO_PMA_DEVAD, 0xA819 + adj, 0x0000); + bnx2x_cl45_write(bp, phy, MDIO_PMA_DEVAD, 0xA81A + adj, 0xc200); + bnx2x_cl45_write(bp, phy, MDIO_PMA_DEVAD, 0xA817 + adj, 0x000A); for (cnt = 0; cnt < 100; cnt++) { - bnx2x_cl45_read(bp, phy, MDIO_PMA_DEVAD, 0xA818, &val); + bnx2x_cl45_read(bp, phy, MDIO_PMA_DEVAD, 0xA818 + adj, &val); if (val & 1) break; udelay(5); @@ -5894,9 +6007,9 @@ static void bnx2x_save_848xx_spirom_version(struct bnx2x_phy *phy, } /* lower 16 bits of the register SPI_FW_STATUS */ - bnx2x_cl45_read(bp, phy, MDIO_PMA_DEVAD, 0xA81B, &fw_ver1); + bnx2x_cl45_read(bp, phy, MDIO_PMA_DEVAD, 0xA81B + adj, &fw_ver1); /* upper 16 bits of register SPI_FW_STATUS */ - bnx2x_cl45_read(bp, phy, MDIO_PMA_DEVAD, 0xA81C, &fw_ver2); + bnx2x_cl45_read(bp, phy, MDIO_PMA_DEVAD, 0xA81C + adj, &fw_ver2); bnx2x_save_spirom_version(bp, params->port, (fw_ver2<<16) | fw_ver1, phy->ver_addr); @@ -5905,49 +6018,53 @@ static void bnx2x_save_848xx_spirom_version(struct bnx2x_phy *phy, static void bnx2x_848xx_set_led(struct bnx2x *bp, struct bnx2x_phy *phy) { - u16 val; + u16 val, adj; + + adj = 0; + if (phy->type == PORT_HW_CFG_XGXS_EXT_PHY_TYPE_BCM84833) + adj = -1; /* PHYC_CTL_LED_CTL */ bnx2x_cl45_read(bp, phy, MDIO_PMA_DEVAD, - MDIO_PMA_REG_8481_LINK_SIGNAL, &val); + MDIO_PMA_REG_8481_LINK_SIGNAL + adj, &val); val &= 0xFE00; val |= 0x0092; bnx2x_cl45_write(bp, phy, MDIO_PMA_DEVAD, - MDIO_PMA_REG_8481_LINK_SIGNAL, val); + MDIO_PMA_REG_8481_LINK_SIGNAL + adj, val); bnx2x_cl45_write(bp, phy, MDIO_PMA_DEVAD, - MDIO_PMA_REG_8481_LED1_MASK, + MDIO_PMA_REG_8481_LED1_MASK + adj, 0x80); bnx2x_cl45_write(bp, phy, MDIO_PMA_DEVAD, - MDIO_PMA_REG_8481_LED2_MASK, + MDIO_PMA_REG_8481_LED2_MASK + adj, 0x18); /* Select activity source by Tx and Rx, as suggested by PHY AE */ bnx2x_cl45_write(bp, phy, MDIO_PMA_DEVAD, - MDIO_PMA_REG_8481_LED3_MASK, + MDIO_PMA_REG_8481_LED3_MASK + adj, 0x0006); /* Select the closest activity blink rate to that in 10/100/1000 */ bnx2x_cl45_write(bp, phy, MDIO_PMA_DEVAD, - MDIO_PMA_REG_8481_LED3_BLINK, + MDIO_PMA_REG_8481_LED3_BLINK + adj, 0); bnx2x_cl45_read(bp, phy, MDIO_PMA_DEVAD, - MDIO_PMA_REG_84823_CTL_LED_CTL_1, &val); + MDIO_PMA_REG_84823_CTL_LED_CTL_1 + adj, &val); val |= MDIO_PMA_REG_84823_LED3_STRETCH_EN; /* stretch_en for LED3*/ bnx2x_cl45_write(bp, phy, MDIO_PMA_DEVAD, - MDIO_PMA_REG_84823_CTL_LED_CTL_1, val); + MDIO_PMA_REG_84823_CTL_LED_CTL_1 + adj, val); /* 'Interrupt Mask' */ bnx2x_cl45_write(bp, phy, @@ -5961,7 +6078,11 @@ static u8 bnx2x_848xx_cmn_config_init(struct bnx2x_phy *phy, { struct bnx2x *bp = params->bp; u16 autoneg_val, an_1000_val, an_10_100_val; - + /* + * This phy uses the NIG latch mechanism since link indication + * arrives through its LED4 and not via its LASI signal, so we + * get steady signal instead of clear on read + */ bnx2x_bits_en(bp, NIG_REG_LATCH_BC_0 + params->port*4, 1 << NIG_LATCH_BC_ENABLE_MI_INT); @@ -6086,11 +6207,11 @@ static u8 bnx2x_8481_config_init(struct bnx2x_phy *phy, struct bnx2x *bp = params->bp; /* Restore normal power mode*/ bnx2x_set_gpio(bp, MISC_REGISTERS_GPIO_2, - MISC_REGISTERS_GPIO_OUTPUT_HIGH, params->port); + MISC_REGISTERS_GPIO_OUTPUT_HIGH, params->port); /* HW reset */ bnx2x_ext_phy_hw_reset(bp, params->port); - bnx2x_wait_reset_complete(bp, phy); + bnx2x_wait_reset_complete(bp, phy, params); bnx2x_cl45_write(bp, phy, MDIO_PMA_DEVAD, MDIO_PMA_REG_CTRL, 1<<15); return bnx2x_848xx_cmn_config_init(phy, params, vars); @@ -6102,12 +6223,15 @@ static u8 bnx2x_848x3_config_init(struct bnx2x_phy *phy, { struct bnx2x *bp = params->bp; u8 port, initialize = 1; - u16 val; + u16 val, adj; u16 temp; - u32 actual_phy_selection; + u32 actual_phy_selection, cms_enable; u8 rc = 0; /* This is just for MDIO_CTL_REG_84823_MEDIA register. */ + adj = 0; + if (phy->type == PORT_HW_CFG_XGXS_EXT_PHY_TYPE_BCM84833) + adj = 3; msleep(1); if (CHIP_IS_E2(bp)) @@ -6117,11 +6241,12 @@ static u8 bnx2x_848x3_config_init(struct bnx2x_phy *phy, bnx2x_set_gpio(bp, MISC_REGISTERS_GPIO_3, MISC_REGISTERS_GPIO_OUTPUT_HIGH, port); - bnx2x_wait_reset_complete(bp, phy); + bnx2x_wait_reset_complete(bp, phy, params); /* Wait for GPHY to come out of reset */ msleep(50); - /* BCM84823 requires that XGXS links up first @ 10G for normal - behavior */ + /* + * BCM84823 requires that XGXS links up first @ 10G for normal behavior + */ temp = vars->line_speed; vars->line_speed = SPEED_10000; bnx2x_set_autoneg(¶ms->phy[INT_PHY], params, vars, 0); @@ -6131,7 +6256,7 @@ static u8 bnx2x_848x3_config_init(struct bnx2x_phy *phy, /* Set dual-media configuration according to configuration */ bnx2x_cl45_read(bp, phy, MDIO_CTL_DEVAD, - MDIO_CTL_REG_84823_MEDIA, &val); + MDIO_CTL_REG_84823_MEDIA + adj, &val); val &= ~(MDIO_CTL_REG_84823_MEDIA_MAC_MASK | MDIO_CTL_REG_84823_MEDIA_LINE_MASK | MDIO_CTL_REG_84823_MEDIA_COPPER_CORE_DOWN | @@ -6164,7 +6289,7 @@ static u8 bnx2x_848x3_config_init(struct bnx2x_phy *phy, val |= MDIO_CTL_REG_84823_MEDIA_FIBER_1G; bnx2x_cl45_write(bp, phy, MDIO_CTL_DEVAD, - MDIO_CTL_REG_84823_MEDIA, val); + MDIO_CTL_REG_84823_MEDIA + adj, val); DP(NETIF_MSG_LINK, "Multi_phy config = 0x%x, Media control = 0x%x\n", params->multi_phy_config, val); @@ -6172,23 +6297,43 @@ static u8 bnx2x_848x3_config_init(struct bnx2x_phy *phy, rc = bnx2x_848xx_cmn_config_init(phy, params, vars); else bnx2x_save_848xx_spirom_version(phy, params); + cms_enable = REG_RD(bp, params->shmem_base + + offsetof(struct shmem_region, + dev_info.port_hw_config[params->port].default_cfg)) & + PORT_HW_CFG_ENABLE_CMS_MASK; + + bnx2x_cl45_read(bp, phy, MDIO_CTL_DEVAD, + MDIO_CTL_REG_84823_USER_CTRL_REG, &val); + if (cms_enable) + val |= MDIO_CTL_REG_84823_USER_CTRL_CMS; + else + val &= ~MDIO_CTL_REG_84823_USER_CTRL_CMS; + bnx2x_cl45_write(bp, phy, MDIO_CTL_DEVAD, + MDIO_CTL_REG_84823_USER_CTRL_REG, val); + + return rc; } static u8 bnx2x_848xx_read_status(struct bnx2x_phy *phy, - struct link_params *params, - struct link_vars *vars) + struct link_params *params, + struct link_vars *vars) { struct bnx2x *bp = params->bp; - u16 val, val1, val2; + u16 val, val1, val2, adj; u8 link_up = 0; + /* Reg offset adjustment for 84833 */ + adj = 0; + if (phy->type == PORT_HW_CFG_XGXS_EXT_PHY_TYPE_BCM84833) + adj = -1; + /* Check 10G-BaseT link status */ /* Check PMD signal ok */ bnx2x_cl45_read(bp, phy, MDIO_AN_DEVAD, 0xFFFA, &val1); bnx2x_cl45_read(bp, phy, - MDIO_PMA_DEVAD, MDIO_PMA_REG_8481_PMD_SIGNAL, + MDIO_PMA_DEVAD, MDIO_PMA_REG_8481_PMD_SIGNAL + adj, &val2); DP(NETIF_MSG_LINK, "BCM848xx: PMD_SIGNAL 1.a811 = 0x%x\n", val2); @@ -6273,9 +6418,9 @@ static void bnx2x_8481_hw_reset(struct bnx2x_phy *phy, struct link_params *params) { bnx2x_set_gpio(params->bp, MISC_REGISTERS_GPIO_1, - MISC_REGISTERS_GPIO_OUTPUT_LOW, 0); + MISC_REGISTERS_GPIO_OUTPUT_LOW, 0); bnx2x_set_gpio(params->bp, MISC_REGISTERS_GPIO_1, - MISC_REGISTERS_GPIO_OUTPUT_LOW, 1); + MISC_REGISTERS_GPIO_OUTPUT_LOW, 1); } static void bnx2x_8481_link_reset(struct bnx2x_phy *phy, @@ -6297,8 +6442,8 @@ static void bnx2x_848x3_link_reset(struct bnx2x_phy *phy, else port = params->port; bnx2x_set_gpio(bp, MISC_REGISTERS_GPIO_3, - MISC_REGISTERS_GPIO_OUTPUT_LOW, - port); + MISC_REGISTERS_GPIO_OUTPUT_LOW, + port); } static void bnx2x_848xx_set_link_led(struct bnx2x_phy *phy, @@ -6353,24 +6498,24 @@ static void bnx2x_848xx_set_link_led(struct bnx2x_phy *phy, /* Set LED masks */ bnx2x_cl45_write(bp, phy, - MDIO_PMA_DEVAD, - MDIO_PMA_REG_8481_LED1_MASK, - 0x0); + MDIO_PMA_DEVAD, + MDIO_PMA_REG_8481_LED1_MASK, + 0x0); bnx2x_cl45_write(bp, phy, - MDIO_PMA_DEVAD, - MDIO_PMA_REG_8481_LED2_MASK, - 0x0); + MDIO_PMA_DEVAD, + MDIO_PMA_REG_8481_LED2_MASK, + 0x0); bnx2x_cl45_write(bp, phy, - MDIO_PMA_DEVAD, - MDIO_PMA_REG_8481_LED3_MASK, - 0x0); + MDIO_PMA_DEVAD, + MDIO_PMA_REG_8481_LED3_MASK, + 0x0); bnx2x_cl45_write(bp, phy, - MDIO_PMA_DEVAD, - MDIO_PMA_REG_8481_LED5_MASK, - 0x20); + MDIO_PMA_DEVAD, + MDIO_PMA_REG_8481_LED5_MASK, + 0x20); } else { bnx2x_cl45_write(bp, phy, @@ -6394,35 +6539,35 @@ static void bnx2x_848xx_set_link_led(struct bnx2x_phy *phy, val |= 0x2492; bnx2x_cl45_write(bp, phy, - MDIO_PMA_DEVAD, - MDIO_PMA_REG_8481_LINK_SIGNAL, - val); + MDIO_PMA_DEVAD, + MDIO_PMA_REG_8481_LINK_SIGNAL, + val); /* Set LED masks */ bnx2x_cl45_write(bp, phy, - MDIO_PMA_DEVAD, - MDIO_PMA_REG_8481_LED1_MASK, - 0x0); + MDIO_PMA_DEVAD, + MDIO_PMA_REG_8481_LED1_MASK, + 0x0); bnx2x_cl45_write(bp, phy, - MDIO_PMA_DEVAD, - MDIO_PMA_REG_8481_LED2_MASK, - 0x20); + MDIO_PMA_DEVAD, + MDIO_PMA_REG_8481_LED2_MASK, + 0x20); bnx2x_cl45_write(bp, phy, - MDIO_PMA_DEVAD, - MDIO_PMA_REG_8481_LED3_MASK, - 0x20); + MDIO_PMA_DEVAD, + MDIO_PMA_REG_8481_LED3_MASK, + 0x20); bnx2x_cl45_write(bp, phy, - MDIO_PMA_DEVAD, - MDIO_PMA_REG_8481_LED5_MASK, - 0x0); + MDIO_PMA_DEVAD, + MDIO_PMA_REG_8481_LED5_MASK, + 0x0); } else { bnx2x_cl45_write(bp, phy, - MDIO_PMA_DEVAD, - MDIO_PMA_REG_8481_LED1_MASK, - 0x20); + MDIO_PMA_DEVAD, + MDIO_PMA_REG_8481_LED1_MASK, + 0x20); } break; @@ -6440,9 +6585,9 @@ static void bnx2x_848xx_set_link_led(struct bnx2x_phy *phy, &val); if (!((val & - MDIO_PMA_REG_8481_LINK_SIGNAL_LED4_ENABLE_MASK) - >> MDIO_PMA_REG_8481_LINK_SIGNAL_LED4_ENABLE_SHIFT)){ - DP(NETIF_MSG_LINK, "Seting LINK_SIGNAL\n"); + MDIO_PMA_REG_8481_LINK_SIGNAL_LED4_ENABLE_MASK) + >> MDIO_PMA_REG_8481_LINK_SIGNAL_LED4_ENABLE_SHIFT)) { + DP(NETIF_MSG_LINK, "Setting LINK_SIGNAL\n"); bnx2x_cl45_write(bp, phy, MDIO_PMA_DEVAD, MDIO_PMA_REG_8481_LINK_SIGNAL, @@ -6451,24 +6596,24 @@ static void bnx2x_848xx_set_link_led(struct bnx2x_phy *phy, /* Set LED masks */ bnx2x_cl45_write(bp, phy, - MDIO_PMA_DEVAD, - MDIO_PMA_REG_8481_LED1_MASK, - 0x10); + MDIO_PMA_DEVAD, + MDIO_PMA_REG_8481_LED1_MASK, + 0x10); bnx2x_cl45_write(bp, phy, - MDIO_PMA_DEVAD, - MDIO_PMA_REG_8481_LED2_MASK, - 0x80); + MDIO_PMA_DEVAD, + MDIO_PMA_REG_8481_LED2_MASK, + 0x80); bnx2x_cl45_write(bp, phy, - MDIO_PMA_DEVAD, - MDIO_PMA_REG_8481_LED3_MASK, - 0x98); + MDIO_PMA_DEVAD, + MDIO_PMA_REG_8481_LED3_MASK, + 0x98); bnx2x_cl45_write(bp, phy, - MDIO_PMA_DEVAD, - MDIO_PMA_REG_8481_LED5_MASK, - 0x40); + MDIO_PMA_DEVAD, + MDIO_PMA_REG_8481_LED5_MASK, + 0x40); } else { bnx2x_cl45_write(bp, phy, @@ -6513,10 +6658,10 @@ static u8 bnx2x_7101_config_init(struct bnx2x_phy *phy, /* Restore normal power mode*/ bnx2x_set_gpio(bp, MISC_REGISTERS_GPIO_2, - MISC_REGISTERS_GPIO_OUTPUT_HIGH, params->port); + MISC_REGISTERS_GPIO_OUTPUT_HIGH, params->port); /* HW reset */ bnx2x_ext_phy_hw_reset(bp, params->port); - bnx2x_wait_reset_complete(bp, phy); + bnx2x_wait_reset_complete(bp, phy, params); bnx2x_cl45_write(bp, phy, MDIO_PMA_DEVAD, MDIO_PMA_REG_LASI_CTRL, 0x1); @@ -6563,9 +6708,7 @@ static u8 bnx2x_7101_read_status(struct bnx2x_phy *phy, DP(NETIF_MSG_LINK, "10G-base-T PMA status 0x%x->0x%x\n", val2, val1); link_up = ((val1 & 4) == 4); - /* if link is up - * print the AN outcome of the SFX7101 PHY - */ + /* if link is up print the AN outcome of the SFX7101 PHY */ if (link_up) { bnx2x_cl45_read(bp, phy, MDIO_AN_DEVAD, MDIO_AN_REG_MASTER_STATUS, @@ -6599,20 +6742,20 @@ void bnx2x_sfx7101_sp_sw_reset(struct bnx2x *bp, struct bnx2x_phy *phy) u16 val, cnt; bnx2x_cl45_read(bp, phy, - MDIO_PMA_DEVAD, - MDIO_PMA_REG_7101_RESET, &val); + MDIO_PMA_DEVAD, + MDIO_PMA_REG_7101_RESET, &val); for (cnt = 0; cnt < 10; cnt++) { msleep(50); /* Writes a self-clearing reset */ bnx2x_cl45_write(bp, phy, - MDIO_PMA_DEVAD, - MDIO_PMA_REG_7101_RESET, - (val | (1<<15))); + MDIO_PMA_DEVAD, + MDIO_PMA_REG_7101_RESET, + (val | (1<<15))); /* Wait for clear */ bnx2x_cl45_read(bp, phy, - MDIO_PMA_DEVAD, - MDIO_PMA_REG_7101_RESET, &val); + MDIO_PMA_DEVAD, + MDIO_PMA_REG_7101_RESET, &val); if ((val & (1<<15)) == 0) break; @@ -6623,10 +6766,10 @@ static void bnx2x_7101_hw_reset(struct bnx2x_phy *phy, struct link_params *params) { /* Low power mode is controlled by GPIO 2 */ bnx2x_set_gpio(params->bp, MISC_REGISTERS_GPIO_2, - MISC_REGISTERS_GPIO_OUTPUT_LOW, params->port); + MISC_REGISTERS_GPIO_OUTPUT_LOW, params->port); /* The PHY reset is controlled by GPIO 1 */ bnx2x_set_gpio(params->bp, MISC_REGISTERS_GPIO_1, - MISC_REGISTERS_GPIO_OUTPUT_LOW, params->port); + MISC_REGISTERS_GPIO_OUTPUT_LOW, params->port); } static void bnx2x_7101_set_link_led(struct bnx2x_phy *phy, @@ -6668,9 +6811,9 @@ static struct bnx2x_phy phy_null = { .supported = 0, .media_type = ETH_PHY_NOT_PRESENT, .ver_addr = 0, - .req_flow_ctrl = 0, - .req_line_speed = 0, - .speed_cap_mask = 0, + .req_flow_ctrl = 0, + .req_line_speed = 0, + .speed_cap_mask = 0, .req_duplex = 0, .rsrv = 0, .config_init = (config_init_t)NULL, @@ -6705,8 +6848,8 @@ static struct bnx2x_phy phy_serdes = { .media_type = ETH_PHY_UNSPECIFIED, .ver_addr = 0, .req_flow_ctrl = 0, - .req_line_speed = 0, - .speed_cap_mask = 0, + .req_line_speed = 0, + .speed_cap_mask = 0, .req_duplex = 0, .rsrv = 0, .config_init = (config_init_t)bnx2x_init_serdes, @@ -6742,8 +6885,8 @@ static struct bnx2x_phy phy_xgxs = { .media_type = ETH_PHY_UNSPECIFIED, .ver_addr = 0, .req_flow_ctrl = 0, - .req_line_speed = 0, - .speed_cap_mask = 0, + .req_line_speed = 0, + .speed_cap_mask = 0, .req_duplex = 0, .rsrv = 0, .config_init = (config_init_t)bnx2x_init_xgxs, @@ -6773,8 +6916,8 @@ static struct bnx2x_phy phy_7101 = { .media_type = ETH_PHY_BASE_T, .ver_addr = 0, .req_flow_ctrl = 0, - .req_line_speed = 0, - .speed_cap_mask = 0, + .req_line_speed = 0, + .speed_cap_mask = 0, .req_duplex = 0, .rsrv = 0, .config_init = (config_init_t)bnx2x_7101_config_init, @@ -6804,9 +6947,9 @@ static struct bnx2x_phy phy_8073 = { SUPPORTED_Asym_Pause), .media_type = ETH_PHY_UNSPECIFIED, .ver_addr = 0, - .req_flow_ctrl = 0, - .req_line_speed = 0, - .speed_cap_mask = 0, + .req_flow_ctrl = 0, + .req_line_speed = 0, + .speed_cap_mask = 0, .req_duplex = 0, .rsrv = 0, .config_init = (config_init_t)bnx2x_8073_config_init, @@ -7015,6 +7158,43 @@ static struct bnx2x_phy phy_84823 = { .phy_specific_func = (phy_specific_func_t)NULL }; +static struct bnx2x_phy phy_84833 = { + .type = PORT_HW_CFG_XGXS_EXT_PHY_TYPE_BCM84833, + .addr = 0xff, + .flags = FLAGS_FAN_FAILURE_DET_REQ | + FLAGS_REARM_LATCH_SIGNAL, + .def_md_devad = 0, + .reserved = 0, + .rx_preemphasis = {0xffff, 0xffff, 0xffff, 0xffff}, + .tx_preemphasis = {0xffff, 0xffff, 0xffff, 0xffff}, + .mdio_ctrl = 0, + .supported = (SUPPORTED_10baseT_Half | + SUPPORTED_10baseT_Full | + SUPPORTED_100baseT_Half | + SUPPORTED_100baseT_Full | + SUPPORTED_1000baseT_Full | + SUPPORTED_10000baseT_Full | + SUPPORTED_TP | + SUPPORTED_Autoneg | + SUPPORTED_Pause | + SUPPORTED_Asym_Pause), + .media_type = ETH_PHY_BASE_T, + .ver_addr = 0, + .req_flow_ctrl = 0, + .req_line_speed = 0, + .speed_cap_mask = 0, + .req_duplex = 0, + .rsrv = 0, + .config_init = (config_init_t)bnx2x_848x3_config_init, + .read_status = (read_status_t)bnx2x_848xx_read_status, + .link_reset = (link_reset_t)bnx2x_848x3_link_reset, + .config_loopback = (config_loopback_t)NULL, + .format_fw_ver = (format_fw_ver_t)bnx2x_848xx_format_ver, + .hw_reset = (hw_reset_t)NULL, + .set_link_led = (set_link_led_t)bnx2x_848xx_set_link_led, + .phy_specific_func = (phy_specific_func_t)NULL +}; + /*****************************************************************/ /* */ /* Populate the phy according. Main function: bnx2x_populate_phy */ @@ -7028,7 +7208,7 @@ static void bnx2x_populate_preemphasis(struct bnx2x *bp, u32 shmem_base, /* Get the 4 lanes xgxs config rx and tx */ u32 rx = 0, tx = 0, i; for (i = 0; i < 2; i++) { - /** + /* * INT_PHY and EXT_PHY1 share the same value location in the * shmem. When num_phys is greater than 1, than this value * applies only to EXT_PHY1 @@ -7036,19 +7216,19 @@ static void bnx2x_populate_preemphasis(struct bnx2x *bp, u32 shmem_base, if (phy_index == INT_PHY || phy_index == EXT_PHY1) { rx = REG_RD(bp, shmem_base + offsetof(struct shmem_region, - dev_info.port_hw_config[port].xgxs_config_rx[i<<1])); + dev_info.port_hw_config[port].xgxs_config_rx[i<<1])); tx = REG_RD(bp, shmem_base + offsetof(struct shmem_region, - dev_info.port_hw_config[port].xgxs_config_tx[i<<1])); + dev_info.port_hw_config[port].xgxs_config_tx[i<<1])); } else { rx = REG_RD(bp, shmem_base + offsetof(struct shmem_region, - dev_info.port_hw_config[port].xgxs_config2_rx[i<<1])); + dev_info.port_hw_config[port].xgxs_config2_rx[i<<1])); tx = REG_RD(bp, shmem_base + offsetof(struct shmem_region, - dev_info.port_hw_config[port].xgxs_config2_rx[i<<1])); + dev_info.port_hw_config[port].xgxs_config2_rx[i<<1])); } phy->rx_preemphasis[i << 1] = ((rx>>16) & 0xffff); @@ -7168,6 +7348,9 @@ static u8 bnx2x_populate_ext_phy(struct bnx2x *bp, case PORT_HW_CFG_XGXS_EXT_PHY_TYPE_BCM84823: *phy = phy_84823; break; + case PORT_HW_CFG_XGXS_EXT_PHY_TYPE_BCM84833: + *phy = phy_84833; + break; case PORT_HW_CFG_XGXS_EXT_PHY_TYPE_SFX7101: *phy = phy_7101; break; @@ -7182,21 +7365,21 @@ static u8 bnx2x_populate_ext_phy(struct bnx2x *bp, phy->addr = XGXS_EXT_PHY_ADDR(ext_phy_config); bnx2x_populate_preemphasis(bp, shmem_base, phy, port, phy_index); - /** - * The shmem address of the phy version is located on different - * structures. In case this structure is too old, do not set - * the address - */ + /* + * The shmem address of the phy version is located on different + * structures. In case this structure is too old, do not set + * the address + */ config2 = REG_RD(bp, shmem_base + offsetof(struct shmem_region, dev_info.shared_hw_config.config2)); if (phy_index == EXT_PHY1) { phy->ver_addr = shmem_base + offsetof(struct shmem_region, port_mb[port].ext_phy_fw_version); - /* Check specific mdc mdio settings */ - if (config2 & SHARED_HW_CFG_MDC_MDIO_ACCESS1_MASK) - mdc_mdio_access = config2 & - SHARED_HW_CFG_MDC_MDIO_ACCESS1_MASK; + /* Check specific mdc mdio settings */ + if (config2 & SHARED_HW_CFG_MDC_MDIO_ACCESS1_MASK) + mdc_mdio_access = config2 & + SHARED_HW_CFG_MDC_MDIO_ACCESS1_MASK; } else { u32 size = REG_RD(bp, shmem2_base); @@ -7215,7 +7398,7 @@ static u8 bnx2x_populate_ext_phy(struct bnx2x *bp, } phy->mdio_ctrl = bnx2x_get_emac_base(bp, mdc_mdio_access, port); - /** + /* * In case mdc/mdio_access of the external phy is different than the * mdc/mdio access of the XGXS, a HW lock must be taken in each access * to prevent one port interfere with another port's CL45 operations. @@ -7250,18 +7433,20 @@ static void bnx2x_phy_def_cfg(struct link_params *params, /* Populate the default phy configuration for MF mode */ if (phy_index == EXT_PHY2) { link_config = REG_RD(bp, params->shmem_base + - offsetof(struct shmem_region, dev_info. + offsetof(struct shmem_region, dev_info. port_feature_config[params->port].link_config2)); phy->speed_cap_mask = REG_RD(bp, params->shmem_base + - offsetof(struct shmem_region, dev_info. + offsetof(struct shmem_region, + dev_info. port_hw_config[params->port].speed_capability_mask2)); } else { link_config = REG_RD(bp, params->shmem_base + - offsetof(struct shmem_region, dev_info. + offsetof(struct shmem_region, dev_info. port_feature_config[params->port].link_config)); phy->speed_cap_mask = REG_RD(bp, params->shmem_base + - offsetof(struct shmem_region, dev_info. - port_hw_config[params->port].speed_capability_mask)); + offsetof(struct shmem_region, + dev_info. + port_hw_config[params->port].speed_capability_mask)); } DP(NETIF_MSG_LINK, "Default config phy idx %x cfg 0x%x speed_cap_mask" " 0x%x\n", phy_index, link_config, phy->speed_cap_mask); @@ -7408,7 +7593,7 @@ static void set_phy_vars(struct link_params *params) else if (phy_index == EXT_PHY2) actual_phy_idx = EXT_PHY1; } - params->phy[actual_phy_idx].req_flow_ctrl = + params->phy[actual_phy_idx].req_flow_ctrl = params->req_flow_ctrl[link_cfg_idx]; params->phy[actual_phy_idx].req_line_speed = @@ -7461,57 +7646,6 @@ u8 bnx2x_phy_init(struct link_params *params, struct link_vars *vars) set_phy_vars(params); DP(NETIF_MSG_LINK, "Num of phys on board: %d\n", params->num_phys); - if (CHIP_REV_IS_FPGA(bp)) { - - vars->link_up = 1; - vars->line_speed = SPEED_10000; - vars->duplex = DUPLEX_FULL; - vars->flow_ctrl = BNX2X_FLOW_CTRL_NONE; - vars->link_status = (LINK_STATUS_LINK_UP | LINK_10GTFD); - /* enable on E1.5 FPGA */ - if (CHIP_IS_E1H(bp)) { - vars->flow_ctrl |= - (BNX2X_FLOW_CTRL_TX | - BNX2X_FLOW_CTRL_RX); - vars->link_status |= - (LINK_STATUS_TX_FLOW_CONTROL_ENABLED | - LINK_STATUS_RX_FLOW_CONTROL_ENABLED); - } - - bnx2x_emac_enable(params, vars, 0); - if (!(CHIP_IS_E2(bp))) - bnx2x_pbf_update(params, vars->flow_ctrl, - vars->line_speed); - /* disable drain */ - REG_WR(bp, NIG_REG_EGRESS_DRAIN0_MODE + params->port*4, 0); - - /* update shared memory */ - bnx2x_update_mng(params, vars->link_status); - - return 0; - - } else - if (CHIP_REV_IS_EMUL(bp)) { - - vars->link_up = 1; - vars->line_speed = SPEED_10000; - vars->duplex = DUPLEX_FULL; - vars->flow_ctrl = BNX2X_FLOW_CTRL_NONE; - vars->link_status = (LINK_STATUS_LINK_UP | LINK_10GTFD); - - bnx2x_bmac_enable(params, vars, 0); - - bnx2x_pbf_update(params, vars->flow_ctrl, vars->line_speed); - /* Disable drain */ - REG_WR(bp, NIG_REG_EGRESS_DRAIN0_MODE - + params->port*4, 0); - - /* update shared memory */ - bnx2x_update_mng(params, vars->link_status); - - return 0; - - } else if (params->loopback_mode == LOOPBACK_BMAC) { vars->link_up = 1; @@ -7527,8 +7661,7 @@ u8 bnx2x_phy_init(struct link_params *params, struct link_vars *vars) /* set bmac loopback */ bnx2x_bmac_enable(params, vars, 1); - REG_WR(bp, NIG_REG_EGRESS_DRAIN0_MODE + - params->port*4, 0); + REG_WR(bp, NIG_REG_EGRESS_DRAIN0_MODE + params->port*4, 0); } else if (params->loopback_mode == LOOPBACK_EMAC) { @@ -7544,8 +7677,7 @@ u8 bnx2x_phy_init(struct link_params *params, struct link_vars *vars) /* set bmac loopback */ bnx2x_emac_enable(params, vars, 1); bnx2x_emac_program(params, vars); - REG_WR(bp, NIG_REG_EGRESS_DRAIN0_MODE + - params->port*4, 0); + REG_WR(bp, NIG_REG_EGRESS_DRAIN0_MODE + params->port*4, 0); } else if ((params->loopback_mode == LOOPBACK_XGXS) || (params->loopback_mode == LOOPBACK_EXT_PHY)) { @@ -7568,8 +7700,7 @@ u8 bnx2x_phy_init(struct link_params *params, struct link_vars *vars) bnx2x_emac_program(params, vars); bnx2x_emac_enable(params, vars, 0); } else - bnx2x_bmac_enable(params, vars, 0); - + bnx2x_bmac_enable(params, vars, 0); if (params->loopback_mode == LOOPBACK_XGXS) { /* set 10G XGXS loopback */ params->phy[INT_PHY].config_loopback( @@ -7587,9 +7718,7 @@ u8 bnx2x_phy_init(struct link_params *params, struct link_vars *vars) params); } } - - REG_WR(bp, NIG_REG_EGRESS_DRAIN0_MODE + - params->port*4, 0); + REG_WR(bp, NIG_REG_EGRESS_DRAIN0_MODE + params->port*4, 0); bnx2x_set_led(params, vars, LED_MODE_OPER, vars->line_speed); @@ -7608,7 +7737,7 @@ u8 bnx2x_phy_init(struct link_params *params, struct link_vars *vars) return 0; } u8 bnx2x_link_reset(struct link_params *params, struct link_vars *vars, - u8 reset_ext_phy) + u8 reset_ext_phy) { struct bnx2x *bp = params->bp; u8 phy_index, port = params->port, clear_latch_ind = 0; @@ -7617,10 +7746,10 @@ u8 bnx2x_link_reset(struct link_params *params, struct link_vars *vars, vars->link_status = 0; bnx2x_update_mng(params, vars->link_status); bnx2x_bits_dis(bp, NIG_REG_MASK_INTERRUPT_PORT0 + port*4, - (NIG_MASK_XGXS0_LINK_STATUS | - NIG_MASK_XGXS0_LINK10G | - NIG_MASK_SERDES0_LINK_STATUS | - NIG_MASK_MI_INT)); + (NIG_MASK_XGXS0_LINK_STATUS | + NIG_MASK_XGXS0_LINK10G | + NIG_MASK_SERDES0_LINK_STATUS | + NIG_MASK_MI_INT)); /* activate nig drain */ REG_WR(bp, NIG_REG_EGRESS_DRAIN0_MODE + port*4, 1); @@ -7719,21 +7848,22 @@ static u8 bnx2x_8073_common_init_phy(struct bnx2x *bp, /* disable attentions */ bnx2x_bits_dis(bp, NIG_REG_MASK_INTERRUPT_PORT0 + port_of_path*4, - (NIG_MASK_XGXS0_LINK_STATUS | - NIG_MASK_XGXS0_LINK10G | - NIG_MASK_SERDES0_LINK_STATUS | - NIG_MASK_MI_INT)); + (NIG_MASK_XGXS0_LINK_STATUS | + NIG_MASK_XGXS0_LINK10G | + NIG_MASK_SERDES0_LINK_STATUS | + NIG_MASK_MI_INT)); /* Need to take the phy out of low power mode in order to write to access its registers */ bnx2x_set_gpio(bp, MISC_REGISTERS_GPIO_2, - MISC_REGISTERS_GPIO_OUTPUT_HIGH, port); + MISC_REGISTERS_GPIO_OUTPUT_HIGH, + port); /* Reset the phy */ bnx2x_cl45_write(bp, &phy[port], - MDIO_PMA_DEVAD, - MDIO_PMA_REG_CTRL, - 1<<15); + MDIO_PMA_DEVAD, + MDIO_PMA_REG_CTRL, + 1<<15); } /* Add delay of 150ms after reset */ @@ -7762,18 +7892,20 @@ static u8 bnx2x_8073_common_init_phy(struct bnx2x *bp, /* Only set bit 10 = 1 (Tx power down) */ bnx2x_cl45_read(bp, phy_blk[port], - MDIO_PMA_DEVAD, - MDIO_PMA_REG_TX_POWER_DOWN, &val); + MDIO_PMA_DEVAD, + MDIO_PMA_REG_TX_POWER_DOWN, &val); /* Phase1 of TX_POWER_DOWN reset */ bnx2x_cl45_write(bp, phy_blk[port], - MDIO_PMA_DEVAD, - MDIO_PMA_REG_TX_POWER_DOWN, - (val | 1<<10)); + MDIO_PMA_DEVAD, + MDIO_PMA_REG_TX_POWER_DOWN, + (val | 1<<10)); } - /* Toggle Transmitter: Power down and then up with 600ms - delay between */ + /* + * Toggle Transmitter: Power down and then up with 600ms delay + * between + */ msleep(600); /* PART3 - complete TX_POWER_DOWN process, and set GPIO2 back to low */ @@ -7781,25 +7913,25 @@ static u8 bnx2x_8073_common_init_phy(struct bnx2x *bp, /* Phase2 of POWER_DOWN_RESET */ /* Release bit 10 (Release Tx power down) */ bnx2x_cl45_read(bp, phy_blk[port], - MDIO_PMA_DEVAD, - MDIO_PMA_REG_TX_POWER_DOWN, &val); + MDIO_PMA_DEVAD, + MDIO_PMA_REG_TX_POWER_DOWN, &val); bnx2x_cl45_write(bp, phy_blk[port], - MDIO_PMA_DEVAD, - MDIO_PMA_REG_TX_POWER_DOWN, (val & (~(1<<10)))); + MDIO_PMA_DEVAD, + MDIO_PMA_REG_TX_POWER_DOWN, (val & (~(1<<10)))); msleep(15); /* Read modify write the SPI-ROM version select register */ bnx2x_cl45_read(bp, phy_blk[port], - MDIO_PMA_DEVAD, - MDIO_PMA_REG_EDC_FFE_MAIN, &val); + MDIO_PMA_DEVAD, + MDIO_PMA_REG_EDC_FFE_MAIN, &val); bnx2x_cl45_write(bp, phy_blk[port], - MDIO_PMA_DEVAD, - MDIO_PMA_REG_EDC_FFE_MAIN, (val | (1<<12))); + MDIO_PMA_DEVAD, + MDIO_PMA_REG_EDC_FFE_MAIN, (val | (1<<12))); /* set GPIO2 back to LOW */ bnx2x_set_gpio(bp, MISC_REGISTERS_GPIO_2, - MISC_REGISTERS_GPIO_OUTPUT_LOW, port); + MISC_REGISTERS_GPIO_OUTPUT_LOW, port); } return 0; } @@ -7846,32 +7978,90 @@ static u8 bnx2x_8726_common_init_phy(struct bnx2x *bp, /* Set fault module detected LED on */ bnx2x_set_gpio(bp, MISC_REGISTERS_GPIO_0, - MISC_REGISTERS_GPIO_HIGH, - port); + MISC_REGISTERS_GPIO_HIGH, + port); } return 0; } +static void bnx2x_get_ext_phy_reset_gpio(struct bnx2x *bp, u32 shmem_base, + u8 *io_gpio, u8 *io_port) +{ + + u32 phy_gpio_reset = REG_RD(bp, shmem_base + + offsetof(struct shmem_region, + dev_info.port_hw_config[PORT_0].default_cfg)); + switch (phy_gpio_reset) { + case PORT_HW_CFG_EXT_PHY_GPIO_RST_GPIO0_P0: + *io_gpio = 0; + *io_port = 0; + break; + case PORT_HW_CFG_EXT_PHY_GPIO_RST_GPIO1_P0: + *io_gpio = 1; + *io_port = 0; + break; + case PORT_HW_CFG_EXT_PHY_GPIO_RST_GPIO2_P0: + *io_gpio = 2; + *io_port = 0; + break; + case PORT_HW_CFG_EXT_PHY_GPIO_RST_GPIO3_P0: + *io_gpio = 3; + *io_port = 0; + break; + case PORT_HW_CFG_EXT_PHY_GPIO_RST_GPIO0_P1: + *io_gpio = 0; + *io_port = 1; + break; + case PORT_HW_CFG_EXT_PHY_GPIO_RST_GPIO1_P1: + *io_gpio = 1; + *io_port = 1; + break; + case PORT_HW_CFG_EXT_PHY_GPIO_RST_GPIO2_P1: + *io_gpio = 2; + *io_port = 1; + break; + case PORT_HW_CFG_EXT_PHY_GPIO_RST_GPIO3_P1: + *io_gpio = 3; + *io_port = 1; + break; + default: + /* Don't override the io_gpio and io_port */ + break; + } +} static u8 bnx2x_8727_common_init_phy(struct bnx2x *bp, u32 shmem_base_path[], u32 shmem2_base_path[], u8 phy_index, u32 chip_id) { - s8 port; + s8 port, reset_gpio; u32 swap_val, swap_override; struct bnx2x_phy phy[PORT_MAX]; struct bnx2x_phy *phy_blk[PORT_MAX]; s8 port_of_path; - swap_val = REG_RD(bp, NIG_REG_PORT_SWAP); - swap_override = REG_RD(bp, NIG_REG_STRAP_OVERRIDE); + swap_val = REG_RD(bp, NIG_REG_PORT_SWAP); + swap_override = REG_RD(bp, NIG_REG_STRAP_OVERRIDE); + reset_gpio = MISC_REGISTERS_GPIO_1; port = 1; - bnx2x_ext_phy_hw_reset(bp, port ^ (swap_val && swap_override)); + /* + * Retrieve the reset gpio/port which control the reset. + * Default is GPIO1, PORT1 + */ + bnx2x_get_ext_phy_reset_gpio(bp, shmem_base_path[0], + (u8 *)&reset_gpio, (u8 *)&port); /* Calculate the port based on port swap */ port ^= (swap_val && swap_override); + /* Initiate PHY reset*/ + bnx2x_set_gpio(bp, reset_gpio, MISC_REGISTERS_GPIO_OUTPUT_LOW, + port); + msleep(1); + bnx2x_set_gpio(bp, reset_gpio, MISC_REGISTERS_GPIO_OUTPUT_HIGH, + port); + msleep(5); /* PART1 - Reset both phys */ @@ -7907,9 +8097,7 @@ static u8 bnx2x_8727_common_init_phy(struct bnx2x *bp, /* Reset the phy */ bnx2x_cl45_write(bp, &phy[port], - MDIO_PMA_DEVAD, - MDIO_PMA_REG_CTRL, - 1<<15); + MDIO_PMA_DEVAD, MDIO_PMA_REG_CTRL, 1<<15); } /* Add delay of 150ms after reset */ @@ -7923,7 +8111,7 @@ static u8 bnx2x_8727_common_init_phy(struct bnx2x *bp, } /* PART2 - Download firmware to both phys */ for (port = PORT_MAX - 1; port >= PORT_0; port--) { - if (CHIP_IS_E2(bp)) + if (CHIP_IS_E2(bp)) port_of_path = 0; else port_of_path = port; @@ -7958,8 +8146,10 @@ static u8 bnx2x_ext_phy_common_init(struct bnx2x *bp, u32 shmem_base_path[], break; case PORT_HW_CFG_XGXS_EXT_PHY_TYPE_BCM8726: - /* GPIO1 affects both ports, so there's need to pull - it for single port alone */ + /* + * GPIO1 affects both ports, so there's need to pull + * it for single port alone + */ rc = bnx2x_8726_common_init_phy(bp, shmem_base_path, shmem2_base_path, phy_index, chip_id); @@ -7969,11 +8159,15 @@ static u8 bnx2x_ext_phy_common_init(struct bnx2x *bp, u32 shmem_base_path[], break; default: DP(NETIF_MSG_LINK, - "bnx2x_common_init_phy: ext_phy 0x%x not required\n", - ext_phy_type); + "ext_phy 0x%x common init not required\n", + ext_phy_type); break; } + if (rc != 0) + netdev_err(bp->dev, "Warning: PHY was not initialized," + " Port %d\n", + 0); return rc; } @@ -7986,9 +8180,6 @@ u8 bnx2x_common_init_phy(struct bnx2x *bp, u32 shmem_base_path[], u32 ext_phy_type, ext_phy_config; DP(NETIF_MSG_LINK, "Begin common phy init\n"); - if (CHIP_REV_IS_EMUL(bp)) - return 0; - /* Check if common init was already done */ phy_ver = REG_RD(bp, shmem_base_path[0] + offsetof(struct shmem_region, |