diff options
Diffstat (limited to 'drivers/net/de620.c')
| -rw-r--r-- | drivers/net/de620.c | 38 |
1 files changed, 19 insertions, 19 deletions
diff --git a/drivers/net/de620.c b/drivers/net/de620.c index 22fc5b869a60..a18d4d14b665 100644 --- a/drivers/net/de620.c +++ b/drivers/net/de620.c @@ -40,7 +40,7 @@ *****************************************************************************/ static const char version[] = "de620.c: $Revision: 1.40 $, Bjorn Ekwall <bj0rn@blox.se>\n"; - + /*********************************************************************** * * "Tuning" section. @@ -115,7 +115,7 @@ static const char version[] = #define COUNT_LOOPS */ #endif - + #include <linux/module.h> #include <linux/kernel.h> #include <linux/types.h> @@ -250,7 +250,7 @@ static struct nic { byte Media; byte SCR; } nic_data; - + /********************************************************** * * * Convenience macros/functions for D-Link DE-620 adapter * @@ -432,7 +432,7 @@ de620_get_register(struct net_device *dev, byte reg) return value; } - + /********************************************************************* * * Open/initialize the board. @@ -515,10 +515,10 @@ static void de620_set_multicast_list(struct net_device *dev) } /******************************************************* - * + * * Handle timeouts on transmit */ - + static void de620_timeout(struct net_device *dev) { printk(KERN_WARNING "%s: transmit timed out, %s?\n", dev->name, "network cable problem"); @@ -540,9 +540,9 @@ static int de620_start_xmit(struct sk_buff *skb, struct net_device *dev) byte using_txbuf; using_txbuf = de620_tx_buffs(dev); /* Peek at the adapter */ - + netif_stop_queue(dev); - + if ((len = skb->len) < RUNT) len = RUNT; @@ -584,7 +584,7 @@ static int de620_start_xmit(struct sk_buff *skb, struct net_device *dev) dev_kfree_skb (skb); return 0; } - + /***************************************************** * * Handle the network interface interrupts. @@ -599,7 +599,7 @@ de620_interrupt(int irq_in, void *dev_id, struct pt_regs *regs) int again = 0; spin_lock(&de620_lock); - + /* Read the status register (_not_ the status port) */ irq_status = de620_get_register(dev, R_STS); @@ -615,7 +615,7 @@ de620_interrupt(int irq_in, void *dev_id, struct pt_regs *regs) if(de620_tx_buffs(dev) != (TXBF0 | TXBF1)) netif_wake_queue(dev); - + spin_unlock(&de620_lock); return IRQ_HANDLED; } @@ -720,7 +720,7 @@ static int de620_rx_intr(struct net_device *dev) return (next_rx_page != curr_page); /* That was slightly tricky... */ } - + /********************************************* * * Reset the adapter to a known state @@ -803,7 +803,7 @@ static int adapter_init(struct net_device *dev) return 0; /* all ok */ } - + /****************************************************************************** * * Only start-up code below @@ -827,7 +827,7 @@ struct net_device * __init de620_probe(int unit) SET_MODULE_OWNER(dev); spin_lock_init(&de620_lock); - + /* * This is where the base_addr and irq gets set. * Tunable at compile-time and insmod-time @@ -840,7 +840,7 @@ struct net_device * __init de620_probe(int unit) sprintf(dev->name, "eth%d", unit); netdev_boot_setup_check(dev); } - + if (de620_debug) printk(version); @@ -889,7 +889,7 @@ struct net_device * __init de620_probe(int unit) dev->tx_timeout = de620_timeout; dev->watchdog_timeo = HZ*2; dev->set_multicast_list = de620_set_multicast_list; - + /* base_addr and irq are already set, see above! */ /* dump eeprom */ @@ -917,7 +917,7 @@ out1: out: return ERR_PTR(err); } - + /********************************** * * Read info from on-board EEPROM @@ -1003,7 +1003,7 @@ static int __init read_eeprom(struct net_device *dev) return 0; /* no errors */ } - + /****************************************************************************** * * Loadable module skeleton @@ -1029,7 +1029,7 @@ void cleanup_module(void) #endif /* MODULE */ MODULE_LICENSE("GPL"); - + /* * (add '-DMODULE' when compiling as loadable module) * |