summaryrefslogtreecommitdiff
path: root/drivers/net/ethernet/8390/smc-ultra32.c
diff options
context:
space:
mode:
Diffstat (limited to 'drivers/net/ethernet/8390/smc-ultra32.c')
-rw-r--r--drivers/net/ethernet/8390/smc-ultra32.c463
1 files changed, 0 insertions, 463 deletions
diff --git a/drivers/net/ethernet/8390/smc-ultra32.c b/drivers/net/ethernet/8390/smc-ultra32.c
deleted file mode 100644
index 923e42aedcfd..000000000000
--- a/drivers/net/ethernet/8390/smc-ultra32.c
+++ /dev/null
@@ -1,463 +0,0 @@
-/* smc-ultra32.c: An SMC Ultra32 EISA ethernet driver for linux.
-
-Sources:
-
- This driver is based on (cloned from) the ISA SMC Ultra driver
- written by Donald Becker. Modifications to support the EISA
- version of the card by Paul Gortmaker and Leonard N. Zubkoff.
-
- This software may be used and distributed according to the terms
- of the GNU General Public License, incorporated herein by reference.
-
-Theory of Operation:
-
- The SMC Ultra32C card uses the SMC 83c790 chip which is also
- found on the ISA SMC Ultra cards. It has a shared memory mode of
- operation that makes it similar to the ISA version of the card.
- The main difference is that the EISA card has 32KB of RAM, but
- only an 8KB window into that memory. The EISA card also can be
- set for a bus-mastering mode of operation via the ECU, but that
- is not (and probably will never be) supported by this driver.
- The ECU should be run to enable shared memory and to disable the
- bus-mastering feature for use with linux.
-
- By programming the 8390 to use only 8KB RAM, the modifications
- to the ISA driver can be limited to the probe and initialization
- code. This allows easy integration of EISA support into the ISA
- driver. However, the driver development kit from SMC provided the
- register information for sliding the 8KB window, and hence the 8390
- is programmed to use the full 32KB RAM.
-
- Unfortunately this required code changes outside the probe/init
- routines, and thus we decided to separate the EISA driver from
- the ISA one. In this way, ISA users don't end up with a larger
- driver due to the EISA code, and EISA users don't end up with a
- larger driver due to the ISA EtherEZ PIO code. The driver is
- similar to the 3c503/16 driver, in that the window must be set
- back to the 1st 8KB of space for access to the two 8390 Tx slots.
-
- In testing, using only 8KB RAM (3 Tx / 5 Rx) didn't appear to
- be a limiting factor, since the EISA bus could get packets off
- the card fast enough, but having the use of lots of RAM as Rx
- space is extra insurance if interrupt latencies become excessive.
-
-*/
-
-static const char *version = "smc-ultra32.c: 06/97 v1.00\n";
-
-
-#include <linux/module.h>
-#include <linux/eisa.h>
-#include <linux/kernel.h>
-#include <linux/errno.h>
-#include <linux/string.h>
-#include <linux/init.h>
-#include <linux/interrupt.h>
-#include <linux/netdevice.h>
-#include <linux/etherdevice.h>
-
-#include <asm/io.h>
-
-#include "8390.h"
-
-#define DRV_NAME "smc-ultra32"
-
-static int ultra32_probe1(struct net_device *dev, int ioaddr);
-static int ultra32_open(struct net_device *dev);
-static void ultra32_reset_8390(struct net_device *dev);
-static void ultra32_get_8390_hdr(struct net_device *dev, struct e8390_pkt_hdr *hdr,
- int ring_page);
-static void ultra32_block_input(struct net_device *dev, int count,
- struct sk_buff *skb, int ring_offset);
-static void ultra32_block_output(struct net_device *dev, int count,
- const unsigned char *buf,
- const int start_page);
-static int ultra32_close(struct net_device *dev);
-
-#define ULTRA32_CMDREG 0 /* Offset to ASIC command register. */
-#define ULTRA32_RESET 0x80 /* Board reset, in ULTRA32_CMDREG. */
-#define ULTRA32_MEMENB 0x40 /* Enable the shared memory. */
-#define ULTRA32_NIC_OFFSET 16 /* NIC register offset from the base_addr. */
-#define ULTRA32_IO_EXTENT 32
-#define EN0_ERWCNT 0x08 /* Early receive warning count. */
-
-/*
- * Defines that apply only to the Ultra32 EISA card. Note that
- * "smc" = 10011 01101 00011 = 0x4da3, and hence !smc8010.cfg translates
- * into an EISA ID of 0x1080A34D
- */
-#define ULTRA32_BASE 0xca0
-#define ULTRA32_ID 0x1080a34d
-#define ULTRA32_IDPORT (-0x20) /* 0xc80 */
-/* Config regs 1->7 from the EISA !SMC8010.CFG file. */
-#define ULTRA32_CFG1 0x04 /* 0xca4 */
-#define ULTRA32_CFG2 0x05 /* 0xca5 */
-#define ULTRA32_CFG3 (-0x18) /* 0xc88 */
-#define ULTRA32_CFG4 (-0x17) /* 0xc89 */
-#define ULTRA32_CFG5 (-0x16) /* 0xc8a */
-#define ULTRA32_CFG6 (-0x15) /* 0xc8b */
-#define ULTRA32_CFG7 0x0d /* 0xcad */
-
-static void cleanup_card(struct net_device *dev)
-{
- int ioaddr = dev->base_addr - ULTRA32_NIC_OFFSET;
- /* NB: ultra32_close_card() does free_irq */
- release_region(ioaddr, ULTRA32_IO_EXTENT);
- iounmap(ei_status.mem);
-}
-
-/* Probe for the Ultra32. This looks like a 8013 with the station
- address PROM at I/O ports <base>+8 to <base>+13, with a checksum
- following.
-*/
-
-struct net_device * __init ultra32_probe(int unit)
-{
- struct net_device *dev;
- int base;
- int irq;
- int err = -ENODEV;
-
- if (!EISA_bus)
- return ERR_PTR(-ENODEV);
-
- dev = alloc_ei_netdev();
-
- if (!dev)
- return ERR_PTR(-ENOMEM);
-
- if (unit >= 0) {
- sprintf(dev->name, "eth%d", unit);
- netdev_boot_setup_check(dev);
- }
-
- irq = dev->irq;
-
- /* EISA spec allows for up to 16 slots, but 8 is typical. */
- for (base = 0x1000 + ULTRA32_BASE; base < 0x9000; base += 0x1000) {
- if (ultra32_probe1(dev, base) == 0)
- break;
- dev->irq = irq;
- }
- if (base >= 0x9000)
- goto out;
- err = register_netdev(dev);
- if (err)
- goto out1;
- return dev;
-out1:
- cleanup_card(dev);
-out:
- free_netdev(dev);
- return ERR_PTR(err);
-}
-
-
-static const struct net_device_ops ultra32_netdev_ops = {
- .ndo_open = ultra32_open,
- .ndo_stop = ultra32_close,
- .ndo_start_xmit = ei_start_xmit,
- .ndo_tx_timeout = ei_tx_timeout,
- .ndo_get_stats = ei_get_stats,
- .ndo_set_rx_mode = ei_set_multicast_list,
- .ndo_validate_addr = eth_validate_addr,
- .ndo_set_mac_address = eth_mac_addr,
- .ndo_change_mtu = eth_change_mtu,
-#ifdef CONFIG_NET_POLL_CONTROLLER
- .ndo_poll_controller = ei_poll,
-#endif
-};
-
-static int __init ultra32_probe1(struct net_device *dev, int ioaddr)
-{
- int i, edge, media, retval;
- int checksum = 0;
- const char *model_name;
- static unsigned version_printed;
- /* Values from various config regs. */
- unsigned char idreg;
- unsigned char reg4;
- const char *ifmap[] = {"UTP No Link", "", "UTP/AUI", "UTP/BNC"};
-
- if (!request_region(ioaddr, ULTRA32_IO_EXTENT, DRV_NAME))
- return -EBUSY;
-
- if (inb(ioaddr + ULTRA32_IDPORT) == 0xff ||
- inl(ioaddr + ULTRA32_IDPORT) != ULTRA32_ID) {
- retval = -ENODEV;
- goto out;
- }
-
- media = inb(ioaddr + ULTRA32_CFG7) & 0x03;
- edge = inb(ioaddr + ULTRA32_CFG5) & 0x08;
- printk("SMC Ultra32 in EISA Slot %d, Media: %s, %s IRQs.\n",
- ioaddr >> 12, ifmap[media],
- (edge ? "Edge Triggered" : "Level Sensitive"));
-
- idreg = inb(ioaddr + 7);
- reg4 = inb(ioaddr + 4) & 0x7f;
-
- /* Check the ID nibble. */
- if ((idreg & 0xf0) != 0x20) { /* SMC Ultra */
- retval = -ENODEV;
- goto out;
- }
-
- /* Select the station address register set. */
- outb(reg4, ioaddr + 4);
-
- for (i = 0; i < 8; i++)
- checksum += inb(ioaddr + 8 + i);
- if ((checksum & 0xff) != 0xff) {
- retval = -ENODEV;
- goto out;
- }
-
- if (ei_debug && version_printed++ == 0)
- printk(version);
-
- model_name = "SMC Ultra32";
-
- for (i = 0; i < 6; i++)
- dev->dev_addr[i] = inb(ioaddr + 8 + i);
-
- printk("%s: %s at 0x%X, %pM",
- dev->name, model_name, ioaddr, dev->dev_addr);
-
- /* Switch from the station address to the alternate register set and
- read the useful registers there. */
- outb(0x80 | reg4, ioaddr + 4);
-
- /* Enable FINE16 mode to avoid BIOS ROM width mismatches @ reboot. */
- outb(0x80 | inb(ioaddr + 0x0c), ioaddr + 0x0c);
-
- /* Reset RAM addr. */
- outb(0x00, ioaddr + 0x0b);
-
- /* Switch back to the station address register set so that the
- MS-DOS driver can find the card after a warm boot. */
- outb(reg4, ioaddr + 4);
-
- if ((inb(ioaddr + ULTRA32_CFG5) & 0x40) == 0) {
- printk("\nsmc-ultra32: Card RAM is disabled! "
- "Run EISA config utility.\n");
- retval = -ENODEV;
- goto out;
- }
- if ((inb(ioaddr + ULTRA32_CFG2) & 0x04) == 0)
- printk("\nsmc-ultra32: Ignoring Bus-Master enable bit. "
- "Run EISA config utility.\n");
-
- if (dev->irq < 2) {
- unsigned char irqmap[] = {0, 9, 3, 5, 7, 10, 11, 15};
- int irq = irqmap[inb(ioaddr + ULTRA32_CFG5) & 0x07];
- if (irq == 0) {
- printk(", failed to detect IRQ line.\n");
- retval = -EAGAIN;
- goto out;
- }
- dev->irq = irq;
- }
-
- /* The 8390 isn't at the base address, so fake the offset */
- dev->base_addr = ioaddr + ULTRA32_NIC_OFFSET;
-
- /* Save RAM address in the unused reg0 to avoid excess inb's. */
- ei_status.reg0 = inb(ioaddr + ULTRA32_CFG3) & 0xfc;
-
- dev->mem_start = 0xc0000 + ((ei_status.reg0 & 0x7c) << 11);
-
- ei_status.name = model_name;
- ei_status.word16 = 1;
- ei_status.tx_start_page = 0;
- ei_status.rx_start_page = TX_PAGES;
- /* All Ultra32 cards have 32KB memory with an 8KB window. */
- ei_status.stop_page = 128;
-
- ei_status.mem = ioremap(dev->mem_start, 0x2000);
- if (!ei_status.mem) {
- printk(", failed to ioremap.\n");
- retval = -ENOMEM;
- goto out;
- }
- dev->mem_end = dev->mem_start + 0x1fff;
-
- printk(", IRQ %d, 32KB memory, 8KB window at 0x%lx-0x%lx.\n",
- dev->irq, dev->mem_start, dev->mem_end);
- ei_status.block_input = &ultra32_block_input;
- ei_status.block_output = &ultra32_block_output;
- ei_status.get_8390_hdr = &ultra32_get_8390_hdr;
- ei_status.reset_8390 = &ultra32_reset_8390;
-
- dev->netdev_ops = &ultra32_netdev_ops;
- NS8390_init(dev, 0);
-
- return 0;
-out:
- release_region(ioaddr, ULTRA32_IO_EXTENT);
- return retval;
-}
-
-static int ultra32_open(struct net_device *dev)
-{
- int ioaddr = dev->base_addr - ULTRA32_NIC_OFFSET; /* ASIC addr */
- int irq_flags = (inb(ioaddr + ULTRA32_CFG5) & 0x08) ? 0 : IRQF_SHARED;
- int retval;
-
- retval = request_irq(dev->irq, ei_interrupt, irq_flags, dev->name, dev);
- if (retval)
- return retval;
-
- outb(ULTRA32_MEMENB, ioaddr); /* Enable Shared Memory. */
- outb(0x80, ioaddr + ULTRA32_CFG6); /* Enable Interrupts. */
- outb(0x84, ioaddr + 5); /* Enable MEM16 & Disable Bus Master. */
- outb(0x01, ioaddr + 6); /* Enable Interrupts. */
- /* Set the early receive warning level in window 0 high enough not
- to receive ERW interrupts. */
- outb_p(E8390_NODMA+E8390_PAGE0, dev->base_addr);
- outb(0xff, dev->base_addr + EN0_ERWCNT);
- ei_open(dev);
- return 0;
-}
-
-static int ultra32_close(struct net_device *dev)
-{
- int ioaddr = dev->base_addr - ULTRA32_NIC_OFFSET; /* CMDREG */
-
- netif_stop_queue(dev);
-
- if (ei_debug > 1)
- printk("%s: Shutting down ethercard.\n", dev->name);
-
- outb(0x00, ioaddr + ULTRA32_CFG6); /* Disable Interrupts. */
- outb(0x00, ioaddr + 6); /* Disable interrupts. */
- free_irq(dev->irq, dev);
-
- NS8390_init(dev, 0);
-
- return 0;
-}
-
-static void ultra32_reset_8390(struct net_device *dev)
-{
- int ioaddr = dev->base_addr - ULTRA32_NIC_OFFSET; /* ASIC base addr */
-
- outb(ULTRA32_RESET, ioaddr);
- if (ei_debug > 1) printk("resetting Ultra32, t=%ld...", jiffies);
- ei_status.txing = 0;
-
- outb(ULTRA32_MEMENB, ioaddr); /* Enable Shared Memory. */
- outb(0x80, ioaddr + ULTRA32_CFG6); /* Enable Interrupts. */
- outb(0x84, ioaddr + 5); /* Enable MEM16 & Disable Bus Master. */
- outb(0x01, ioaddr + 6); /* Enable Interrupts. */
- if (ei_debug > 1) printk("reset done\n");
-}
-
-/* Grab the 8390 specific header. Similar to the block_input routine, but
- we don't need to be concerned with ring wrap as the header will be at
- the start of a page, so we optimize accordingly. */
-
-static void ultra32_get_8390_hdr(struct net_device *dev,
- struct e8390_pkt_hdr *hdr,
- int ring_page)
-{
- void __iomem *hdr_start = ei_status.mem + ((ring_page & 0x1f) << 8);
- unsigned int RamReg = dev->base_addr - ULTRA32_NIC_OFFSET + ULTRA32_CFG3;
-
- /* Select correct 8KB Window. */
- outb(ei_status.reg0 | ((ring_page & 0x60) >> 5), RamReg);
-
-#ifdef __BIG_ENDIAN
- /* Officially this is what we are doing, but the readl() is faster */
- /* unfortunately it isn't endian aware of the struct */
- memcpy_fromio(hdr, hdr_start, sizeof(struct e8390_pkt_hdr));
- hdr->count = le16_to_cpu(hdr->count);
-#else
- ((unsigned int*)hdr)[0] = readl(hdr_start);
-#endif
-}
-
-/* Block input and output are easy on shared memory ethercards, the only
- complication is when the ring buffer wraps, or in this case, when a
- packet spans an 8KB boundary. Note that the current 8KB segment is
- already set by the get_8390_hdr routine. */
-
-static void ultra32_block_input(struct net_device *dev,
- int count,
- struct sk_buff *skb,
- int ring_offset)
-{
- void __iomem *xfer_start = ei_status.mem + (ring_offset & 0x1fff);
- unsigned int RamReg = dev->base_addr - ULTRA32_NIC_OFFSET + ULTRA32_CFG3;
-
- if ((ring_offset & ~0x1fff) != ((ring_offset + count - 1) & ~0x1fff)) {
- int semi_count = 8192 - (ring_offset & 0x1FFF);
- memcpy_fromio(skb->data, xfer_start, semi_count);
- count -= semi_count;
- if (ring_offset < 96*256) {
- /* Select next 8KB Window. */
- ring_offset += semi_count;
- outb(ei_status.reg0 | ((ring_offset & 0x6000) >> 13), RamReg);
- memcpy_fromio(skb->data + semi_count, ei_status.mem, count);
- } else {
- /* Select first 8KB Window. */
- outb(ei_status.reg0, RamReg);
- memcpy_fromio(skb->data + semi_count, ei_status.mem + TX_PAGES * 256, count);
- }
- } else {
- memcpy_fromio(skb->data, xfer_start, count);
- }
-}
-
-static void ultra32_block_output(struct net_device *dev,
- int count,
- const unsigned char *buf,
- int start_page)
-{
- void __iomem *xfer_start = ei_status.mem + (start_page<<8);
- unsigned int RamReg = dev->base_addr - ULTRA32_NIC_OFFSET + ULTRA32_CFG3;
-
- /* Select first 8KB Window. */
- outb(ei_status.reg0, RamReg);
-
- memcpy_toio(xfer_start, buf, count);
-}
-
-#ifdef MODULE
-#define MAX_ULTRA32_CARDS 4 /* Max number of Ultra cards per module */
-static struct net_device *dev_ultra[MAX_ULTRA32_CARDS];
-
-MODULE_DESCRIPTION("SMC Ultra32 EISA ethernet driver");
-MODULE_LICENSE("GPL");
-
-int __init init_module(void)
-{
- int this_dev, found = 0;
-
- for (this_dev = 0; this_dev < MAX_ULTRA32_CARDS; this_dev++) {
- struct net_device *dev = ultra32_probe(-1);
- if (IS_ERR(dev))
- break;
- dev_ultra[found++] = dev;
- }
- if (found)
- return 0;
- printk(KERN_WARNING "smc-ultra32.c: No SMC Ultra32 found.\n");
- return -ENXIO;
-}
-
-void __exit cleanup_module(void)
-{
- int this_dev;
-
- for (this_dev = 0; this_dev < MAX_ULTRA32_CARDS; this_dev++) {
- struct net_device *dev = dev_ultra[this_dev];
- if (dev) {
- unregister_netdev(dev);
- cleanup_card(dev);
- free_netdev(dev);
- }
- }
-}
-#endif /* MODULE */
-