summaryrefslogtreecommitdiff
path: root/drivers/net/wireless/iwlwifi/iwl-4965-hw.h
diff options
context:
space:
mode:
Diffstat (limited to 'drivers/net/wireless/iwlwifi/iwl-4965-hw.h')
-rw-r--r--drivers/net/wireless/iwlwifi/iwl-4965-hw.h2062
1 files changed, 1777 insertions, 285 deletions
diff --git a/drivers/net/wireless/iwlwifi/iwl-4965-hw.h b/drivers/net/wireless/iwlwifi/iwl-4965-hw.h
index 99a19ef4c743..ff71c09ab1a7 100644
--- a/drivers/net/wireless/iwlwifi/iwl-4965-hw.h
+++ b/drivers/net/wireless/iwlwifi/iwl-4965-hw.h
@@ -8,7 +8,7 @@
* Copyright(c) 2005 - 2007 Intel Corporation. All rights reserved.
*
* This program is free software; you can redistribute it and/or modify
- * it under the terms of version 2 of the GNU Geeral Public License as
+ * it under the terms of version 2 of the GNU General Public License as
* published by the Free Software Foundation.
*
* This program is distributed in the hope that it will be useful, but
@@ -60,48 +60,618 @@
* OF THIS SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE.
*
*****************************************************************************/
+/*
+ * Please use this file (iwl-4965-hw.h) only for hardware-related definitions.
+ * Use iwl-4965-commands.h for uCode API definitions.
+ * Use iwl-4965.h for driver implementation definitions.
+ */
#ifndef __iwl_4965_hw_h__
#define __iwl_4965_hw_h__
-#define IWL_RX_BUF_SIZE (4 * 1024)
-#define IWL_MAX_BSM_SIZE BSM_SRAM_SIZE
+/*
+ * uCode queue management definitions ...
+ * Queue #4 is the command queue for 3945 and 4965; map it to Tx FIFO chnl 4.
+ * The first queue used for block-ack aggregation is #7 (4965 only).
+ * All block-ack aggregation queues should map to Tx DMA/FIFO channel 7.
+ */
+#define IWL_CMD_QUEUE_NUM 4
+#define IWL_CMD_FIFO_NUM 4
+#define IWL_BACK_QUEUE_FIRST_ID 7
+
+/* Tx rates */
+#define IWL_CCK_RATES 4
+#define IWL_OFDM_RATES 8
+#define IWL_HT_RATES 16
+#define IWL_MAX_RATES (IWL_CCK_RATES+IWL_OFDM_RATES+IWL_HT_RATES)
+
+/* Time constants */
+#define SHORT_SLOT_TIME 9
+#define LONG_SLOT_TIME 20
+
+/* RSSI to dBm */
+#define IWL_RSSI_OFFSET 44
+
+/*
+ * EEPROM related constants, enums, and structures.
+ */
+
+/*
+ * EEPROM access time values:
+ *
+ * Driver initiates EEPROM read by writing byte address << 1 to CSR_EEPROM_REG,
+ * then clearing (with subsequent read/modify/write) CSR_EEPROM_REG bit
+ * CSR_EEPROM_REG_BIT_CMD (0x2).
+ * Driver then polls CSR_EEPROM_REG for CSR_EEPROM_REG_READ_VALID_MSK (0x1).
+ * When polling, wait 10 uSec between polling loops, up to a maximum 5000 uSec.
+ * Driver reads 16-bit value from bits 31-16 of CSR_EEPROM_REG.
+ */
+#define IWL_EEPROM_ACCESS_TIMEOUT 5000 /* uSec */
+#define IWL_EEPROM_ACCESS_DELAY 10 /* uSec */
+
+/*
+ * Regulatory channel usage flags in EEPROM struct iwl4965_eeprom_channel.flags.
+ *
+ * IBSS and/or AP operation is allowed *only* on those channels with
+ * (VALID && IBSS && ACTIVE && !RADAR). This restriction is in place because
+ * RADAR detection is not supported by the 4965 driver, but is a
+ * requirement for establishing a new network for legal operation on channels
+ * requiring RADAR detection or restricting ACTIVE scanning.
+ *
+ * NOTE: "WIDE" flag does not indicate anything about "FAT" 40 MHz channels.
+ * It only indicates that 20 MHz channel use is supported; FAT channel
+ * usage is indicated by a separate set of regulatory flags for each
+ * FAT channel pair.
+ *
+ * NOTE: Using a channel inappropriately will result in a uCode error!
+ */
+enum {
+ EEPROM_CHANNEL_VALID = (1 << 0), /* usable for this SKU/geo */
+ EEPROM_CHANNEL_IBSS = (1 << 1), /* usable as an IBSS channel */
+ /* Bit 2 Reserved */
+ EEPROM_CHANNEL_ACTIVE = (1 << 3), /* active scanning allowed */
+ EEPROM_CHANNEL_RADAR = (1 << 4), /* radar detection required */
+ EEPROM_CHANNEL_WIDE = (1 << 5), /* 20 MHz channel okay */
+ EEPROM_CHANNEL_NARROW = (1 << 6), /* 10 MHz channel (not used) */
+ EEPROM_CHANNEL_DFS = (1 << 7), /* dynamic freq selection candidate */
+};
+
+/* SKU Capabilities */
+#define EEPROM_SKU_CAP_SW_RF_KILL_ENABLE (1 << 0)
+#define EEPROM_SKU_CAP_HW_RF_KILL_ENABLE (1 << 1)
+
+/* *regulatory* channel data format in eeprom, one for each channel.
+ * There are separate entries for FAT (40 MHz) vs. normal (20 MHz) channels. */
+struct iwl4965_eeprom_channel {
+ u8 flags; /* EEPROM_CHANNEL_* flags copied from EEPROM */
+ s8 max_power_avg; /* max power (dBm) on this chnl, limit 31 */
+} __attribute__ ((packed));
+
+/* 4965 has two radio transmitters (and 3 radio receivers) */
+#define EEPROM_TX_POWER_TX_CHAINS (2)
+
+/* 4965 has room for up to 8 sets of txpower calibration data */
+#define EEPROM_TX_POWER_BANDS (8)
+
+/* 4965 factory calibration measures txpower gain settings for
+ * each of 3 target output levels */
+#define EEPROM_TX_POWER_MEASUREMENTS (3)
+
+/* 4965 driver does not work with txpower calibration version < 5.
+ * Look for this in calib_version member of struct iwl4965_eeprom. */
+#define EEPROM_TX_POWER_VERSION_NEW (5)
+
+
+/*
+ * 4965 factory calibration data for one txpower level, on one channel,
+ * measured on one of the 2 tx chains (radio transmitter and associated
+ * antenna). EEPROM contains:
+ *
+ * 1) Temperature (degrees Celsius) of device when measurement was made.
+ *
+ * 2) Gain table index used to achieve the target measurement power.
+ * This refers to the "well-known" gain tables (see iwl-4965-hw.h).
+ *
+ * 3) Actual measured output power, in half-dBm ("34" = 17 dBm).
+ *
+ * 4) RF power amplifier detector level measurement (not used).
+ */
+struct iwl4965_eeprom_calib_measure {
+ u8 temperature; /* Device temperature (Celsius) */
+ u8 gain_idx; /* Index into gain table */
+ u8 actual_pow; /* Measured RF output power, half-dBm */
+ s8 pa_det; /* Power amp detector level (not used) */
+} __attribute__ ((packed));
+
+
+/*
+ * 4965 measurement set for one channel. EEPROM contains:
+ *
+ * 1) Channel number measured
+ *
+ * 2) Measurements for each of 3 power levels for each of 2 radio transmitters
+ * (a.k.a. "tx chains") (6 measurements altogether)
+ */
+struct iwl4965_eeprom_calib_ch_info {
+ u8 ch_num;
+ struct iwl4965_eeprom_calib_measure measurements[EEPROM_TX_POWER_TX_CHAINS]
+ [EEPROM_TX_POWER_MEASUREMENTS];
+} __attribute__ ((packed));
+
+/*
+ * 4965 txpower subband info.
+ *
+ * For each frequency subband, EEPROM contains the following:
+ *
+ * 1) First and last channels within range of the subband. "0" values
+ * indicate that this sample set is not being used.
+ *
+ * 2) Sample measurement sets for 2 channels close to the range endpoints.
+ */
+struct iwl4965_eeprom_calib_subband_info {
+ u8 ch_from; /* channel number of lowest channel in subband */
+ u8 ch_to; /* channel number of highest channel in subband */
+ struct iwl4965_eeprom_calib_ch_info ch1;
+ struct iwl4965_eeprom_calib_ch_info ch2;
+} __attribute__ ((packed));
+
+
+/*
+ * 4965 txpower calibration info. EEPROM contains:
+ *
+ * 1) Factory-measured saturation power levels (maximum levels at which
+ * tx power amplifier can output a signal without too much distortion).
+ * There is one level for 2.4 GHz band and one for 5 GHz band. These
+ * values apply to all channels within each of the bands.
+ *
+ * 2) Factory-measured power supply voltage level. This is assumed to be
+ * constant (i.e. same value applies to all channels/bands) while the
+ * factory measurements are being made.
+ *
+ * 3) Up to 8 sets of factory-measured txpower calibration values.
+ * These are for different frequency ranges, since txpower gain
+ * characteristics of the analog radio circuitry vary with frequency.
+ *
+ * Not all sets need to be filled with data;
+ * struct iwl4965_eeprom_calib_subband_info contains range of channels
+ * (0 if unused) for each set of data.
+ */
+struct iwl4965_eeprom_calib_info {
+ u8 saturation_power24; /* half-dBm (e.g. "34" = 17 dBm) */
+ u8 saturation_power52; /* half-dBm */
+ s16 voltage; /* signed */
+ struct iwl4965_eeprom_calib_subband_info band_info[EEPROM_TX_POWER_BANDS];
+} __attribute__ ((packed));
+
+
+/*
+ * 4965 EEPROM map
+ */
+struct iwl4965_eeprom {
+ u8 reserved0[16];
+#define EEPROM_DEVICE_ID (2*0x08) /* 2 bytes */
+ u16 device_id; /* abs.ofs: 16 */
+ u8 reserved1[2];
+#define EEPROM_PMC (2*0x0A) /* 2 bytes */
+ u16 pmc; /* abs.ofs: 20 */
+ u8 reserved2[20];
+#define EEPROM_MAC_ADDRESS (2*0x15) /* 6 bytes */
+ u8 mac_address[6]; /* abs.ofs: 42 */
+ u8 reserved3[58];
+#define EEPROM_BOARD_REVISION (2*0x35) /* 2 bytes */
+ u16 board_revision; /* abs.ofs: 106 */
+ u8 reserved4[11];
+#define EEPROM_BOARD_PBA_NUMBER (2*0x3B+1) /* 9 bytes */
+ u8 board_pba_number[9]; /* abs.ofs: 119 */
+ u8 reserved5[8];
+#define EEPROM_VERSION (2*0x44) /* 2 bytes */
+ u16 version; /* abs.ofs: 136 */
+#define EEPROM_SKU_CAP (2*0x45) /* 1 bytes */
+ u8 sku_cap; /* abs.ofs: 138 */
+#define EEPROM_LEDS_MODE (2*0x45+1) /* 1 bytes */
+ u8 leds_mode; /* abs.ofs: 139 */
+#define EEPROM_OEM_MODE (2*0x46) /* 2 bytes */
+ u16 oem_mode;
+#define EEPROM_WOWLAN_MODE (2*0x47) /* 2 bytes */
+ u16 wowlan_mode; /* abs.ofs: 142 */
+#define EEPROM_LEDS_TIME_INTERVAL (2*0x48) /* 2 bytes */
+ u16 leds_time_interval; /* abs.ofs: 144 */
+#define EEPROM_LEDS_OFF_TIME (2*0x49) /* 1 bytes */
+ u8 leds_off_time; /* abs.ofs: 146 */
+#define EEPROM_LEDS_ON_TIME (2*0x49+1) /* 1 bytes */
+ u8 leds_on_time; /* abs.ofs: 147 */
+#define EEPROM_ALMGOR_M_VERSION (2*0x4A) /* 1 bytes */
+ u8 almgor_m_version; /* abs.ofs: 148 */
+#define EEPROM_ANTENNA_SWITCH_TYPE (2*0x4A+1) /* 1 bytes */
+ u8 antenna_switch_type; /* abs.ofs: 149 */
+ u8 reserved6[8];
+#define EEPROM_4965_BOARD_REVISION (2*0x4F) /* 2 bytes */
+ u16 board_revision_4965; /* abs.ofs: 158 */
+ u8 reserved7[13];
+#define EEPROM_4965_BOARD_PBA (2*0x56+1) /* 9 bytes */
+ u8 board_pba_number_4965[9]; /* abs.ofs: 173 */
+ u8 reserved8[10];
+#define EEPROM_REGULATORY_SKU_ID (2*0x60) /* 4 bytes */
+ u8 sku_id[4]; /* abs.ofs: 192 */
+
+/*
+ * Per-channel regulatory data.
+ *
+ * Each channel that *might* be supported by 3945 or 4965 has a fixed location
+ * in EEPROM containing EEPROM_CHANNEL_* usage flags (LSB) and max regulatory
+ * txpower (MSB).
+ *
+ * Entries immediately below are for 20 MHz channel width. FAT (40 MHz)
+ * channels (only for 4965, not supported by 3945) appear later in the EEPROM.
+ *
+ * 2.4 GHz channels 1, 2, 3, 4, 5, 6, 7, 8, 9, 10, 11, 12, 13, 14
+ */
+#define EEPROM_REGULATORY_BAND_1 (2*0x62) /* 2 bytes */
+ u16 band_1_count; /* abs.ofs: 196 */
+#define EEPROM_REGULATORY_BAND_1_CHANNELS (2*0x63) /* 28 bytes */
+ struct iwl4965_eeprom_channel band_1_channels[14]; /* abs.ofs: 196 */
+
+/*
+ * 4.9 GHz channels 183, 184, 185, 187, 188, 189, 192, 196,
+ * 5.0 GHz channels 7, 8, 11, 12, 16
+ * (4915-5080MHz) (none of these is ever supported)
+ */
+#define EEPROM_REGULATORY_BAND_2 (2*0x71) /* 2 bytes */
+ u16 band_2_count; /* abs.ofs: 226 */
+#define EEPROM_REGULATORY_BAND_2_CHANNELS (2*0x72) /* 26 bytes */
+ struct iwl4965_eeprom_channel band_2_channels[13]; /* abs.ofs: 228 */
+
+/*
+ * 5.2 GHz channels 34, 36, 38, 40, 42, 44, 46, 48, 52, 56, 60, 64
+ * (5170-5320MHz)
+ */
+#define EEPROM_REGULATORY_BAND_3 (2*0x7F) /* 2 bytes */
+ u16 band_3_count; /* abs.ofs: 254 */
+#define EEPROM_REGULATORY_BAND_3_CHANNELS (2*0x80) /* 24 bytes */
+ struct iwl4965_eeprom_channel band_3_channels[12]; /* abs.ofs: 256 */
+
+/*
+ * 5.5 GHz channels 100, 104, 108, 112, 116, 120, 124, 128, 132, 136, 140
+ * (5500-5700MHz)
+ */
+#define EEPROM_REGULATORY_BAND_4 (2*0x8C) /* 2 bytes */
+ u16 band_4_count; /* abs.ofs: 280 */
+#define EEPROM_REGULATORY_BAND_4_CHANNELS (2*0x8D) /* 22 bytes */
+ struct iwl4965_eeprom_channel band_4_channels[11]; /* abs.ofs: 282 */
+
+/*
+ * 5.7 GHz channels 145, 149, 153, 157, 161, 165
+ * (5725-5825MHz)
+ */
+#define EEPROM_REGULATORY_BAND_5 (2*0x98) /* 2 bytes */
+ u16 band_5_count; /* abs.ofs: 304 */
+#define EEPROM_REGULATORY_BAND_5_CHANNELS (2*0x99) /* 12 bytes */
+ struct iwl4965_eeprom_channel band_5_channels[6]; /* abs.ofs: 306 */
+
+ u8 reserved10[2];
+
+
+/*
+ * 2.4 GHz FAT channels 1 (5), 2 (6), 3 (7), 4 (8), 5 (9), 6 (10), 7 (11)
+ *
+ * The channel listed is the center of the lower 20 MHz half of the channel.
+ * The overall center frequency is actually 2 channels (10 MHz) above that,
+ * and the upper half of each FAT channel is centered 4 channels (20 MHz) away
+ * from the lower half; e.g. the upper half of FAT channel 1 is channel 5,
+ * and the overall FAT channel width centers on channel 3.
+ *
+ * NOTE: The RXON command uses 20 MHz channel numbers to specify the
+ * control channel to which to tune. RXON also specifies whether the
+ * control channel is the upper or lower half of a FAT channel.
+ *
+ * NOTE: 4965 does not support FAT channels on 2.4 GHz.
+ */
+#define EEPROM_REGULATORY_BAND_24_FAT_CHANNELS (2*0xA0) /* 14 bytes */
+ struct iwl4965_eeprom_channel band_24_channels[7]; /* abs.ofs: 320 */
+ u8 reserved11[2];
+
+/*
+ * 5.2 GHz FAT channels 36 (40), 44 (48), 52 (56), 60 (64),
+ * 100 (104), 108 (112), 116 (120), 124 (128), 132 (136), 149 (153), 157 (161)
+ */
+#define EEPROM_REGULATORY_BAND_52_FAT_CHANNELS (2*0xA8) /* 22 bytes */
+ struct iwl4965_eeprom_channel band_52_channels[11]; /* abs.ofs: 336 */
+ u8 reserved12[6];
+
+/*
+ * 4965 driver requires txpower calibration format version 5 or greater.
+ * Driver does not work with txpower calibration version < 5.
+ * This value is simply a 16-bit number, no major/minor versions here.
+ */
+#define EEPROM_CALIB_VERSION_OFFSET (2*0xB6) /* 2 bytes */
+ u16 calib_version; /* abs.ofs: 364 */
+ u8 reserved13[2];
+ u8 reserved14[96]; /* abs.ofs: 368 */
+
+/*
+ * 4965 Txpower calibration data.
+ */
+#define EEPROM_IWL_CALIB_TXPOWER_OFFSET (2*0xE8) /* 48 bytes */
+ struct iwl4965_eeprom_calib_info calib_info; /* abs.ofs: 464 */
+
+ u8 reserved16[140]; /* fill out to full 1024 byte block */
+
+
+} __attribute__ ((packed));
+
+#define IWL_EEPROM_IMAGE_SIZE 1024
+
+/* End of EEPROM */
+
+#include "iwl-4965-commands.h"
+
+#define PCI_LINK_CTRL 0x0F0
+#define PCI_POWER_SOURCE 0x0C8
+#define PCI_REG_WUM8 0x0E8
+#define PCI_CFG_PMC_PME_FROM_D3COLD_SUPPORT (0x80000000)
+
+/*=== CSR (control and status registers) ===*/
+#define CSR_BASE (0x000)
+
+#define CSR_SW_VER (CSR_BASE+0x000)
+#define CSR_HW_IF_CONFIG_REG (CSR_BASE+0x000) /* hardware interface config */
+#define CSR_INT_COALESCING (CSR_BASE+0x004) /* accum ints, 32-usec units */
+#define CSR_INT (CSR_BASE+0x008) /* host interrupt status/ack */
+#define CSR_INT_MASK (CSR_BASE+0x00c) /* host interrupt enable */
+#define CSR_FH_INT_STATUS (CSR_BASE+0x010) /* busmaster int status/ack*/
+#define CSR_GPIO_IN (CSR_BASE+0x018) /* read external chip pins */
+#define CSR_RESET (CSR_BASE+0x020) /* busmaster enable, NMI, etc*/
+#define CSR_GP_CNTRL (CSR_BASE+0x024)
+
+/*
+ * Hardware revision info
+ * Bit fields:
+ * 31-8: Reserved
+ * 7-4: Type of device: 0x0 = 4965, 0xd = 3945
+ * 3-2: Revision step: 0 = A, 1 = B, 2 = C, 3 = D
+ * 1-0: "Dash" value, as in A-1, etc.
+ *
+ * NOTE: Revision step affects calculation of CCK txpower for 4965.
+ */
+#define CSR_HW_REV (CSR_BASE+0x028)
+
+/* EEPROM reads */
+#define CSR_EEPROM_REG (CSR_BASE+0x02c)
+#define CSR_EEPROM_GP (CSR_BASE+0x030)
+#define CSR_GP_UCODE (CSR_BASE+0x044)
+#define CSR_UCODE_DRV_GP1 (CSR_BASE+0x054)
+#define CSR_UCODE_DRV_GP1_SET (CSR_BASE+0x058)
+#define CSR_UCODE_DRV_GP1_CLR (CSR_BASE+0x05c)
+#define CSR_UCODE_DRV_GP2 (CSR_BASE+0x060)
+#define CSR_GIO_CHICKEN_BITS (CSR_BASE+0x100)
+
+/*
+ * Indicates hardware rev, to determine CCK backoff for txpower calculation.
+ * Bit fields:
+ * 3-2: 0 = A, 1 = B, 2 = C, 3 = D step
+ */
+#define CSR_HW_REV_WA_REG (CSR_BASE+0x22C)
+
+/* Hardware interface configuration bits */
+#define CSR_HW_IF_CONFIG_REG_BIT_KEDRON_R (0x00000010)
+#define CSR_HW_IF_CONFIG_REG_MSK_BOARD_VER (0x00000C00)
+#define CSR_HW_IF_CONFIG_REG_BIT_MAC_SI (0x00000100)
+#define CSR_HW_IF_CONFIG_REG_BIT_RADIO_SI (0x00000200)
+#define CSR_HW_IF_CONFIG_REG_BIT_EEPROM_OWN_SEM (0x00200000)
+
+/* interrupt flags in INTA, set by uCode or hardware (e.g. dma),
+ * acknowledged (reset) by host writing "1" to flagged bits. */
+#define CSR_INT_BIT_FH_RX (1 << 31) /* Rx DMA, cmd responses, FH_INT[17:16] */
+#define CSR_INT_BIT_HW_ERR (1 << 29) /* DMA hardware error FH_INT[31] */
+#define CSR_INT_BIT_DNLD (1 << 28) /* uCode Download */
+#define CSR_INT_BIT_FH_TX (1 << 27) /* Tx DMA FH_INT[1:0] */
+#define CSR_INT_BIT_MAC_CLK_ACTV (1 << 26) /* NIC controller's clock toggled on/off */
+#define CSR_INT_BIT_SW_ERR (1 << 25) /* uCode error */
+#define CSR_INT_BIT_RF_KILL (1 << 7) /* HW RFKILL switch GP_CNTRL[27] toggled */
+#define CSR_INT_BIT_CT_KILL (1 << 6) /* Critical temp (chip too hot) rfkill */
+#define CSR_INT_BIT_SW_RX (1 << 3) /* Rx, command responses, 3945 */
+#define CSR_INT_BIT_WAKEUP (1 << 1) /* NIC controller waking up (pwr mgmt) */
+#define CSR_INT_BIT_ALIVE (1 << 0) /* uCode interrupts once it initializes */
+
+#define CSR_INI_SET_MASK (CSR_INT_BIT_FH_RX | \
+ CSR_INT_BIT_HW_ERR | \
+ CSR_INT_BIT_FH_TX | \
+ CSR_INT_BIT_SW_ERR | \
+ CSR_INT_BIT_RF_KILL | \
+ CSR_INT_BIT_SW_RX | \
+ CSR_INT_BIT_WAKEUP | \
+ CSR_INT_BIT_ALIVE)
+
+/* interrupt flags in FH (flow handler) (PCI busmaster DMA) */
+#define CSR_FH_INT_BIT_ERR (1 << 31) /* Error */
+#define CSR_FH_INT_BIT_HI_PRIOR (1 << 30) /* High priority Rx, bypass coalescing */
+#define CSR_FH_INT_BIT_RX_CHNL1 (1 << 17) /* Rx channel 1 */
+#define CSR_FH_INT_BIT_RX_CHNL0 (1 << 16) /* Rx channel 0 */
+#define CSR_FH_INT_BIT_TX_CHNL1 (1 << 1) /* Tx channel 1 */
+#define CSR_FH_INT_BIT_TX_CHNL0 (1 << 0) /* Tx channel 0 */
+
+#define CSR_FH_INT_RX_MASK (CSR_FH_INT_BIT_HI_PRIOR | \
+ CSR_FH_INT_BIT_RX_CHNL1 | \
+ CSR_FH_INT_BIT_RX_CHNL0)
+
+#define CSR_FH_INT_TX_MASK (CSR_FH_INT_BIT_TX_CHNL1 | \
+ CSR_FH_INT_BIT_TX_CHNL0)
+
+
+/* RESET */
+#define CSR_RESET_REG_FLAG_NEVO_RESET (0x00000001)
+#define CSR_RESET_REG_FLAG_FORCE_NMI (0x00000002)
+#define CSR_RESET_REG_FLAG_SW_RESET (0x00000080)
+#define CSR_RESET_REG_FLAG_MASTER_DISABLED (0x00000100)
+#define CSR_RESET_REG_FLAG_STOP_MASTER (0x00000200)
+
+/* GP (general purpose) CONTROL */
+#define CSR_GP_CNTRL_REG_FLAG_MAC_CLOCK_READY (0x00000001)
+#define CSR_GP_CNTRL_REG_FLAG_INIT_DONE (0x00000004)
+#define CSR_GP_CNTRL_REG_FLAG_MAC_ACCESS_REQ (0x00000008)
+#define CSR_GP_CNTRL_REG_FLAG_GOING_TO_SLEEP (0x00000010)
+
+#define CSR_GP_CNTRL_REG_VAL_MAC_ACCESS_EN (0x00000001)
+
+#define CSR_GP_CNTRL_REG_MSK_POWER_SAVE_TYPE (0x07000000)
+#define CSR_GP_CNTRL_REG_FLAG_MAC_POWER_SAVE (0x04000000)
+#define CSR_GP_CNTRL_REG_FLAG_HW_RF_KILL_SW (0x08000000)
+
+
+/* EEPROM REG */
+#define CSR_EEPROM_REG_READ_VALID_MSK (0x00000001)
+#define CSR_EEPROM_REG_BIT_CMD (0x00000002)
+
+/* EEPROM GP */
+#define CSR_EEPROM_GP_VALID_MSK (0x00000006)
+#define CSR_EEPROM_GP_BAD_SIGNATURE (0x00000000)
+#define CSR_EEPROM_GP_IF_OWNER_MSK (0x00000180)
+
+/* UCODE DRV GP */
+#define CSR_UCODE_DRV_GP1_BIT_MAC_SLEEP (0x00000001)
+#define CSR_UCODE_SW_BIT_RFKILL (0x00000002)
+#define CSR_UCODE_DRV_GP1_BIT_CMD_BLOCKED (0x00000004)
+#define CSR_UCODE_DRV_GP1_REG_BIT_CT_KILL_EXIT (0x00000008)
+
+/* GPIO */
+#define CSR_GPIO_IN_BIT_AUX_POWER (0x00000200)
+#define CSR_GPIO_IN_VAL_VAUX_PWR_SRC (0x00000000)
+#define CSR_GPIO_IN_VAL_VMAIN_PWR_SRC CSR_GPIO_IN_BIT_AUX_POWER
+
+/* GI Chicken Bits */
+#define CSR_GIO_CHICKEN_BITS_REG_BIT_L1A_NO_L0S_RX (0x00800000)
+#define CSR_GIO_CHICKEN_BITS_REG_BIT_DIS_L0S_EXIT_TIMER (0x20000000)
+
+/*=== HBUS (Host-side Bus) ===*/
+#define HBUS_BASE (0x400)
+
+/*
+ * Registers for accessing device's internal SRAM memory (e.g. SCD SRAM
+ * structures, error log, event log, verifying uCode load).
+ * First write to address register, then read from or write to data register
+ * to complete the job. Once the address register is set up, accesses to
+ * data registers auto-increment the address by one dword.
+ * Bit usage for address registers (read or write):
+ * 0-31: memory address within device
+ */
+#define HBUS_TARG_MEM_RADDR (HBUS_BASE+0x00c)
+#define HBUS_TARG_MEM_WADDR (HBUS_BASE+0x010)
+#define HBUS_TARG_MEM_WDAT (HBUS_BASE+0x018)
+#define HBUS_TARG_MEM_RDAT (HBUS_BASE+0x01c)
+
+/*
+ * Registers for accessing device's internal peripheral registers
+ * (e.g. SCD, BSM, etc.). First write to address register,
+ * then read from or write to data register to complete the job.
+ * Bit usage for address registers (read or write):
+ * 0-15: register address (offset) within device
+ * 24-25: (# bytes - 1) to read or write (e.g. 3 for dword)
+ */
+#define HBUS_TARG_PRPH_WADDR (HBUS_BASE+0x044)
+#define HBUS_TARG_PRPH_RADDR (HBUS_BASE+0x048)
+#define HBUS_TARG_PRPH_WDAT (HBUS_BASE+0x04c)
+#define HBUS_TARG_PRPH_RDAT (HBUS_BASE+0x050)
+
+/*
+ * Per-Tx-queue write pointer (index, really!) (3945 and 4965).
+ * Driver sets this to indicate index to next TFD that driver will fill
+ * (1 past latest filled).
+ * Bit usage:
+ * 0-7: queue write index (0-255)
+ * 11-8: queue selector (0-15)
+ */
+#define HBUS_TARG_WRPTR (HBUS_BASE+0x060)
+
+#define HBUS_TARG_MBX_C (HBUS_BASE+0x030)
+
+#define HBUS_TARG_MBX_C_REG_BIT_CMD_BLOCKED (0x00000004)
+
+#define TFD_QUEUE_SIZE_MAX (256)
+
+#define IWL_NUM_SCAN_RATES (2)
+
+#define IWL_DEFAULT_TX_RETRY 15
+
+#define RX_QUEUE_SIZE 256
+#define RX_QUEUE_MASK 255
+#define RX_QUEUE_SIZE_LOG 8
+
+#define TFD_TX_CMD_SLOTS 256
+#define TFD_CMD_SLOTS 32
+
+#define TFD_MAX_PAYLOAD_SIZE (sizeof(struct iwl4965_cmd) - \
+ sizeof(struct iwl4965_cmd_meta))
+
+/*
+ * RX related structures and functions
+ */
+#define RX_FREE_BUFFERS 64
+#define RX_LOW_WATERMARK 8
+
+/* Size of one Rx buffer in host DRAM */
+#define IWL_RX_BUF_SIZE_4K (4 * 1024)
+#define IWL_RX_BUF_SIZE_8K (8 * 1024)
+
+/* Sizes and addresses for instruction and data memory (SRAM) in
+ * 4965's embedded processor. Driver access is via HBUS_TARG_MEM_* regs. */
+#define RTC_INST_LOWER_BOUND (0x000000)
#define KDR_RTC_INST_UPPER_BOUND (0x018000)
+
+#define RTC_DATA_LOWER_BOUND (0x800000)
#define KDR_RTC_DATA_UPPER_BOUND (0x80A000)
+
#define KDR_RTC_INST_SIZE (KDR_RTC_INST_UPPER_BOUND - RTC_INST_LOWER_BOUND)
#define KDR_RTC_DATA_SIZE (KDR_RTC_DATA_UPPER_BOUND - RTC_DATA_LOWER_BOUND)
#define IWL_MAX_INST_SIZE KDR_RTC_INST_SIZE
#define IWL_MAX_DATA_SIZE KDR_RTC_DATA_SIZE
-static inline int iwl_hw_valid_rtc_data_addr(u32 addr)
+/* Size of uCode instruction memory in bootstrap state machine */
+#define IWL_MAX_BSM_SIZE BSM_SRAM_SIZE
+
+static inline int iwl4965_hw_valid_rtc_data_addr(u32 addr)
{
return (addr >= RTC_DATA_LOWER_BOUND) &&
(addr < KDR_RTC_DATA_UPPER_BOUND);
}
-/********************* START TXPOWER *****************************************/
-enum {
- HT_IE_EXT_CHANNEL_NONE = 0,
- HT_IE_EXT_CHANNEL_ABOVE,
- HT_IE_EXT_CHANNEL_INVALID,
- HT_IE_EXT_CHANNEL_BELOW,
- HT_IE_EXT_CHANNEL_MAX
-};
-
-enum {
- CALIB_CH_GROUP_1 = 0,
- CALIB_CH_GROUP_2 = 1,
- CALIB_CH_GROUP_3 = 2,
- CALIB_CH_GROUP_4 = 3,
- CALIB_CH_GROUP_5 = 4,
- CALIB_CH_GROUP_MAX
-};
+/********************* START TEMPERATURE *************************************/
-/* Temperature calibration offset is 3% 0C in Kelvin */
+/**
+ * 4965 temperature calculation.
+ *
+ * The driver must calculate the device temperature before calculating
+ * a txpower setting (amplifier gain is temperature dependent). The
+ * calculation uses 4 measurements, 3 of which (R1, R2, R3) are calibration
+ * values used for the life of the driver, and one of which (R4) is the
+ * real-time temperature indicator.
+ *
+ * uCode provides all 4 values to the driver via the "initialize alive"
+ * notification (see struct iwl4965_init_alive_resp). After the runtime uCode
+ * image loads, uCode updates the R4 value via statistics notifications
+ * (see STATISTICS_NOTIFICATION), which occur after each received beacon
+ * when associated, or can be requested via REPLY_STATISTICS_CMD.
+ *
+ * NOTE: uCode provides the R4 value as a 23-bit signed value. Driver
+ * must sign-extend to 32 bits before applying formula below.
+ *
+ * Formula:
+ *
+ * degrees Kelvin = ((97 * 259 * (R4 - R2) / (R3 - R1)) / 100) + 8
+ *
+ * NOTE: The basic formula is 259 * (R4-R2) / (R3-R1). The 97/100 is
+ * an additional correction, which should be centered around 0 degrees
+ * Celsius (273 degrees Kelvin). The 8 (3 percent of 273) compensates for
+ * centering the 97/100 correction around 0 degrees K.
+ *
+ * Add 273 to Kelvin value to find degrees Celsius, for comparing current
+ * temperature with factory-measured temperatures when calculating txpower
+ * settings.
+ */
#define TEMPERATURE_CALIB_KELVIN_OFFSET 8
#define TEMPERATURE_CALIB_A_VAL 259
+/* Limit range of calculated temperature to be between these Kelvin values */
#define IWL_TX_POWER_TEMPERATURE_MIN (263)
#define IWL_TX_POWER_TEMPERATURE_MAX (410)
@@ -109,228 +679,875 @@ enum {
(((t) < IWL_TX_POWER_TEMPERATURE_MIN) || \
((t) > IWL_TX_POWER_TEMPERATURE_MAX))
-#define IWL_TX_POWER_ILLEGAL_TEMPERATURE (300)
+/********************* END TEMPERATURE ***************************************/
-#define IWL_TX_POWER_TEMPERATURE_DIFFERENCE (2)
+/********************* START TXPOWER *****************************************/
-#define IWL_TX_POWER_MIMO_REGULATORY_COMPENSATION (6)
+/**
+ * 4965 txpower calculations rely on information from three sources:
+ *
+ * 1) EEPROM
+ * 2) "initialize" alive notification
+ * 3) statistics notifications
+ *
+ * EEPROM data consists of:
+ *
+ * 1) Regulatory information (max txpower and channel usage flags) is provided
+ * separately for each channel that can possibly supported by 4965.
+ * 40 MHz wide (.11n fat) channels are listed separately from 20 MHz
+ * (legacy) channels.
+ *
+ * See struct iwl4965_eeprom_channel for format, and struct iwl4965_eeprom
+ * for locations in EEPROM.
+ *
+ * 2) Factory txpower calibration information is provided separately for
+ * sub-bands of contiguous channels. 2.4GHz has just one sub-band,
+ * but 5 GHz has several sub-bands.
+ *
+ * In addition, per-band (2.4 and 5 Ghz) saturation txpowers are provided.
+ *
+ * See struct iwl4965_eeprom_calib_info (and the tree of structures
+ * contained within it) for format, and struct iwl4965_eeprom for
+ * locations in EEPROM.
+ *
+ * "Initialization alive" notification (see struct iwl4965_init_alive_resp)
+ * consists of:
+ *
+ * 1) Temperature calculation parameters.
+ *
+ * 2) Power supply voltage measurement.
+ *
+ * 3) Tx gain compensation to balance 2 transmitters for MIMO use.
+ *
+ * Statistics notifications deliver:
+ *
+ * 1) Current values for temperature param R4.
+ */
+
+/**
+ * To calculate a txpower setting for a given desired target txpower, channel,
+ * modulation bit rate, and transmitter chain (4965 has 2 transmitters to
+ * support MIMO and transmit diversity), driver must do the following:
+ *
+ * 1) Compare desired txpower vs. (EEPROM) regulatory limit for this channel.
+ * Do not exceed regulatory limit; reduce target txpower if necessary.
+ *
+ * If setting up txpowers for MIMO rates (rate indexes 8-15, 24-31),
+ * 2 transmitters will be used simultaneously; driver must reduce the
+ * regulatory limit by 3 dB (half-power) for each transmitter, so the
+ * combined total output of the 2 transmitters is within regulatory limits.
+ *
+ *
+ * 2) Compare target txpower vs. (EEPROM) saturation txpower *reduced by
+ * backoff for this bit rate*. Do not exceed (saturation - backoff[rate]);
+ * reduce target txpower if necessary.
+ *
+ * Backoff values below are in 1/2 dB units (equivalent to steps in
+ * txpower gain tables):
+ *
+ * OFDM 6 - 36 MBit: 10 steps (5 dB)
+ * OFDM 48 MBit: 15 steps (7.5 dB)
+ * OFDM 54 MBit: 17 steps (8.5 dB)
+ * OFDM 60 MBit: 20 steps (10 dB)
+ * CCK all rates: 10 steps (5 dB)
+ *
+ * Backoff values apply to saturation txpower on a per-transmitter basis;
+ * when using MIMO (2 transmitters), each transmitter uses the same
+ * saturation level provided in EEPROM, and the same backoff values;
+ * no reduction (such as with regulatory txpower limits) is required.
+ *
+ * Saturation and Backoff values apply equally to 20 Mhz (legacy) channel
+ * widths and 40 Mhz (.11n fat) channel widths; there is no separate
+ * factory measurement for fat channels.
+ *
+ * The result of this step is the final target txpower. The rest of
+ * the steps figure out the proper settings for the device to achieve
+ * that target txpower.
+ *
+ *
+ * 3) Determine (EEPROM) calibration subband for the target channel, by
+ * comparing against first and last channels in each subband
+ * (see struct iwl4965_eeprom_calib_subband_info).
+ *
+ *
+ * 4) Linearly interpolate (EEPROM) factory calibration measurement sets,
+ * referencing the 2 factory-measured (sample) channels within the subband.
+ *
+ * Interpolation is based on difference between target channel's frequency
+ * and the sample channels' frequencies. Since channel numbers are based
+ * on frequency (5 MHz between each channel number), this is equivalent
+ * to interpolating based on channel number differences.
+ *
+ * Note that the sample channels may or may not be the channels at the
+ * edges of the subband. The target channel may be "outside" of the
+ * span of the sampled channels.
+ *
+ * Driver may choose the pair (for 2 Tx chains) of measurements (see
+ * struct iwl4965_eeprom_calib_ch_info) for which the actual measured
+ * txpower comes closest to the desired txpower. Usually, though,
+ * the middle set of measurements is closest to the regulatory limits,
+ * and is therefore a good choice for all txpower calculations (this
+ * assumes that high accuracy is needed for maximizing legal txpower,
+ * while lower txpower configurations do not need as much accuracy).
+ *
+ * Driver should interpolate both members of the chosen measurement pair,
+ * i.e. for both Tx chains (radio transmitters), unless the driver knows
+ * that only one of the chains will be used (e.g. only one tx antenna
+ * connected, but this should be unusual). The rate scaling algorithm
+ * switches antennas to find best performance, so both Tx chains will
+ * be used (although only one at a time) even for non-MIMO transmissions.
+ *
+ * Driver should interpolate factory values for temperature, gain table
+ * index, and actual power. The power amplifier detector values are
+ * not used by the driver.
+ *
+ * Sanity check: If the target channel happens to be one of the sample
+ * channels, the results should agree with the sample channel's
+ * measurements!
+ *
+ *
+ * 5) Find difference between desired txpower and (interpolated)
+ * factory-measured txpower. Using (interpolated) factory gain table index
+ * (shown elsewhere) as a starting point, adjust this index lower to
+ * increase txpower, or higher to decrease txpower, until the target
+ * txpower is reached. Each step in the gain table is 1/2 dB.
+ *
+ * For example, if factory measured txpower is 16 dBm, and target txpower
+ * is 13 dBm, add 6 steps to the factory gain index to reduce txpower
+ * by 3 dB.
+ *
+ *
+ * 6) Find difference between current device temperature and (interpolated)
+ * factory-measured temperature for sub-band. Factory values are in
+ * degrees Celsius. To calculate current temperature, see comments for
+ * "4965 temperature calculation".
+ *
+ * If current temperature is higher than factory temperature, driver must
+ * increase gain (lower gain table index), and vice versa.
+ *
+ * Temperature affects gain differently for different channels:
+ *
+ * 2.4 GHz all channels: 3.5 degrees per half-dB step
+ * 5 GHz channels 34-43: 4.5 degrees per half-dB step
+ * 5 GHz channels >= 44: 4.0 degrees per half-dB step
+ *
+ * NOTE: Temperature can increase rapidly when transmitting, especially
+ * with heavy traffic at high txpowers. Driver should update
+ * temperature calculations often under these conditions to
+ * maintain strong txpower in the face of rising temperature.
+ *
+ *
+ * 7) Find difference between current power supply voltage indicator
+ * (from "initialize alive") and factory-measured power supply voltage
+ * indicator (EEPROM).
+ *
+ * If the current voltage is higher (indicator is lower) than factory
+ * voltage, gain should be reduced (gain table index increased) by:
+ *
+ * (eeprom - current) / 7
+ *
+ * If the current voltage is lower (indicator is higher) than factory
+ * voltage, gain should be increased (gain table index decreased) by:
+ *
+ * 2 * (current - eeprom) / 7
+ *
+ * If number of index steps in either direction turns out to be > 2,
+ * something is wrong ... just use 0.
+ *
+ * NOTE: Voltage compensation is independent of band/channel.
+ *
+ * NOTE: "Initialize" uCode measures current voltage, which is assumed
+ * to be constant after this initial measurement. Voltage
+ * compensation for txpower (number of steps in gain table)
+ * may be calculated once and used until the next uCode bootload.
+ *
+ *
+ * 8) If setting up txpowers for MIMO rates (rate indexes 8-15, 24-31),
+ * adjust txpower for each transmitter chain, so txpower is balanced
+ * between the two chains. There are 5 pairs of tx_atten[group][chain]
+ * values in "initialize alive", one pair for each of 5 channel ranges:
+ *
+ * Group 0: 5 GHz channel 34-43
+ * Group 1: 5 GHz channel 44-70
+ * Group 2: 5 GHz channel 71-124
+ * Group 3: 5 GHz channel 125-200
+ * Group 4: 2.4 GHz all channels
+ *
+ * Add the tx_atten[group][chain] value to the index for the target chain.
+ * The values are signed, but are in pairs of 0 and a non-negative number,
+ * so as to reduce gain (if necessary) of the "hotter" channel. This
+ * avoids any need to double-check for regulatory compliance after
+ * this step.
+ *
+ *
+ * 9) If setting up for a CCK rate, lower the gain by adding a CCK compensation
+ * value to the index:
+ *
+ * Hardware rev B: 9 steps (4.5 dB)
+ * Hardware rev C: 5 steps (2.5 dB)
+ *
+ * Hardware rev for 4965 can be determined by reading CSR_HW_REV_WA_REG,
+ * bits [3:2], 1 = B, 2 = C.
+ *
+ * NOTE: This compensation is in addition to any saturation backoff that
+ * might have been applied in an earlier step.
+ *
+ *
+ * 10) Select the gain table, based on band (2.4 vs 5 GHz).
+ *
+ * Limit the adjusted index to stay within the table!
+ *
+ *
+ * 11) Read gain table entries for DSP and radio gain, place into appropriate
+ * location(s) in command (struct iwl4965_txpowertable_cmd).
+ */
+/* Limit range of txpower output target to be between these values */
#define IWL_TX_POWER_TARGET_POWER_MIN (0) /* 0 dBm = 1 milliwatt */
#define IWL_TX_POWER_TARGET_POWER_MAX (16) /* 16 dBm */
-/* timeout equivalent to 3 minutes */
-#define IWL_TX_POWER_TIMELIMIT_NOCALIB 1800000000
-
-#define IWL_TX_POWER_CCK_COMPENSATION (9)
-
-#define MIN_TX_GAIN_INDEX (0)
-#define MIN_TX_GAIN_INDEX_52GHZ_EXT (-9)
-#define MAX_TX_GAIN_INDEX_52GHZ (98)
-#define MIN_TX_GAIN_52GHZ (98)
-#define MAX_TX_GAIN_INDEX_24GHZ (98)
-#define MIN_TX_GAIN_24GHZ (98)
-#define MAX_TX_GAIN (0)
-#define MAX_TX_GAIN_52GHZ_EXT (-9)
+/**
+ * When MIMO is used (2 transmitters operating simultaneously), driver should
+ * limit each transmitter to deliver a max of 3 dB below the regulatory limit
+ * for the device. That is, use half power for each transmitter, so total
+ * txpower is within regulatory limits.
+ *
+ * The value "6" represents number of steps in gain table to reduce power 3 dB.
+ * Each step is 1/2 dB.
+ */
+#define IWL_TX_POWER_MIMO_REGULATORY_COMPENSATION (6)
+/**
+ * CCK gain compensation.
+ *
+ * When calculating txpowers for CCK, after making sure that the target power
+ * is within regulatory and saturation limits, driver must additionally
+ * back off gain by adding these values to the gain table index.
+ *
+ * Hardware rev for 4965 can be determined by reading CSR_HW_REV_WA_REG,
+ * bits [3:2], 1 = B, 2 = C.
+ */
+#define IWL_TX_POWER_CCK_COMPENSATION_B_STEP (9)
+#define IWL_TX_POWER_CCK_COMPENSATION_C_STEP (5)
+
+/*
+ * 4965 power supply voltage compensation for txpower
+ */
+#define TX_POWER_IWL_VOLTAGE_CODES_PER_03V (7)
+
+/**
+ * Gain tables.
+ *
+ * The following tables contain pair of values for setting txpower, i.e.
+ * gain settings for the output of the device's digital signal processor (DSP),
+ * and for the analog gain structure of the transmitter.
+ *
+ * Each entry in the gain tables represents a step of 1/2 dB. Note that these
+ * are *relative* steps, not indications of absolute output power. Output
+ * power varies with temperature, voltage, and channel frequency, and also
+ * requires consideration of average power (to satisfy regulatory constraints),
+ * and peak power (to avoid distortion of the output signal).
+ *
+ * Each entry contains two values:
+ * 1) DSP gain (or sometimes called DSP attenuation). This is a fine-grained
+ * linear value that multiplies the output of the digital signal processor,
+ * before being sent to the analog radio.
+ * 2) Radio gain. This sets the analog gain of the radio Tx path.
+ * It is a coarser setting, and behaves in a logarithmic (dB) fashion.
+ *
+ * EEPROM contains factory calibration data for txpower. This maps actual
+ * measured txpower levels to gain settings in the "well known" tables
+ * below ("well-known" means here that both factory calibration *and* the
+ * driver work with the same table).
+ *
+ * There are separate tables for 2.4 GHz and 5 GHz bands. The 5 GHz table
+ * has an extension (into negative indexes), in case the driver needs to
+ * boost power setting for high device temperatures (higher than would be
+ * present during factory calibration). A 5 Ghz EEPROM index of "40"
+ * corresponds to the 49th entry in the table used by the driver.
+ */
+#define MIN_TX_GAIN_INDEX (0) /* highest gain, lowest idx, 2.4 */
+#define MIN_TX_GAIN_INDEX_52GHZ_EXT (-9) /* highest gain, lowest idx, 5 */
+
+/**
+ * 2.4 GHz gain table
+ *
+ * Index Dsp gain Radio gain
+ * 0 110 0x3f (highest gain)
+ * 1 104 0x3f
+ * 2 98 0x3f
+ * 3 110 0x3e
+ * 4 104 0x3e
+ * 5 98 0x3e
+ * 6 110 0x3d
+ * 7 104 0x3d
+ * 8 98 0x3d
+ * 9 110 0x3c
+ * 10 104 0x3c
+ * 11 98 0x3c
+ * 12 110 0x3b
+ * 13 104 0x3b
+ * 14 98 0x3b
+ * 15 110 0x3a
+ * 16 104 0x3a
+ * 17 98 0x3a
+ * 18 110 0x39
+ * 19 104 0x39
+ * 20 98 0x39
+ * 21 110 0x38
+ * 22 104 0x38
+ * 23 98 0x38
+ * 24 110 0x37
+ * 25 104 0x37
+ * 26 98 0x37
+ * 27 110 0x36
+ * 28 104 0x36
+ * 29 98 0x36
+ * 30 110 0x35
+ * 31 104 0x35
+ * 32 98 0x35
+ * 33 110 0x34
+ * 34 104 0x34
+ * 35 98 0x34
+ * 36 110 0x33
+ * 37 104 0x33
+ * 38 98 0x33
+ * 39 110 0x32
+ * 40 104 0x32
+ * 41 98 0x32
+ * 42 110 0x31
+ * 43 104 0x31
+ * 44 98 0x31
+ * 45 110 0x30
+ * 46 104 0x30
+ * 47 98 0x30
+ * 48 110 0x6
+ * 49 104 0x6
+ * 50 98 0x6
+ * 51 110 0x5
+ * 52 104 0x5
+ * 53 98 0x5
+ * 54 110 0x4
+ * 55 104 0x4
+ * 56 98 0x4
+ * 57 110 0x3
+ * 58 104 0x3
+ * 59 98 0x3
+ * 60 110 0x2
+ * 61 104 0x2
+ * 62 98 0x2
+ * 63 110 0x1
+ * 64 104 0x1
+ * 65 98 0x1
+ * 66 110 0x0
+ * 67 104 0x0
+ * 68 98 0x0
+ * 69 97 0
+ * 70 96 0
+ * 71 95 0
+ * 72 94 0
+ * 73 93 0
+ * 74 92 0
+ * 75 91 0
+ * 76 90 0
+ * 77 89 0
+ * 78 88 0
+ * 79 87 0
+ * 80 86 0
+ * 81 85 0
+ * 82 84 0
+ * 83 83 0
+ * 84 82 0
+ * 85 81 0
+ * 86 80 0
+ * 87 79 0
+ * 88 78 0
+ * 89 77 0
+ * 90 76 0
+ * 91 75 0
+ * 92 74 0
+ * 93 73 0
+ * 94 72 0
+ * 95 71 0
+ * 96 70 0
+ * 97 69 0
+ * 98 68 0
+ */
+
+/**
+ * 5 GHz gain table
+ *
+ * Index Dsp gain Radio gain
+ * -9 123 0x3F (highest gain)
+ * -8 117 0x3F
+ * -7 110 0x3F
+ * -6 104 0x3F
+ * -5 98 0x3F
+ * -4 110 0x3E
+ * -3 104 0x3E
+ * -2 98 0x3E
+ * -1 110 0x3D
+ * 0 104 0x3D
+ * 1 98 0x3D
+ * 2 110 0x3C
+ * 3 104 0x3C
+ * 4 98 0x3C
+ * 5 110 0x3B
+ * 6 104 0x3B
+ * 7 98 0x3B
+ * 8 110 0x3A
+ * 9 104 0x3A
+ * 10 98 0x3A
+ * 11 110 0x39
+ * 12 104 0x39
+ * 13 98 0x39
+ * 14 110 0x38
+ * 15 104 0x38
+ * 16 98 0x38
+ * 17 110 0x37
+ * 18 104 0x37
+ * 19 98 0x37
+ * 20 110 0x36
+ * 21 104 0x36
+ * 22 98 0x36
+ * 23 110 0x35
+ * 24 104 0x35
+ * 25 98 0x35
+ * 26 110 0x34
+ * 27 104 0x34
+ * 28 98 0x34
+ * 29 110 0x33
+ * 30 104 0x33
+ * 31 98 0x33
+ * 32 110 0x32
+ * 33 104 0x32
+ * 34 98 0x32
+ * 35 110 0x31
+ * 36 104 0x31
+ * 37 98 0x31
+ * 38 110 0x30
+ * 39 104 0x30
+ * 40 98 0x30
+ * 41 110 0x25
+ * 42 104 0x25
+ * 43 98 0x25
+ * 44 110 0x24
+ * 45 104 0x24
+ * 46 98 0x24
+ * 47 110 0x23
+ * 48 104 0x23
+ * 49 98 0x23
+ * 50 110 0x22
+ * 51 104 0x18
+ * 52 98 0x18
+ * 53 110 0x17
+ * 54 104 0x17
+ * 55 98 0x17
+ * 56 110 0x16
+ * 57 104 0x16
+ * 58 98 0x16
+ * 59 110 0x15
+ * 60 104 0x15
+ * 61 98 0x15
+ * 62 110 0x14
+ * 63 104 0x14
+ * 64 98 0x14
+ * 65 110 0x13
+ * 66 104 0x13
+ * 67 98 0x13
+ * 68 110 0x12
+ * 69 104 0x08
+ * 70 98 0x08
+ * 71 110 0x07
+ * 72 104 0x07
+ * 73 98 0x07
+ * 74 110 0x06
+ * 75 104 0x06
+ * 76 98 0x06
+ * 77 110 0x05
+ * 78 104 0x05
+ * 79 98 0x05
+ * 80 110 0x04
+ * 81 104 0x04
+ * 82 98 0x04
+ * 83 110 0x03
+ * 84 104 0x03
+ * 85 98 0x03
+ * 86 110 0x02
+ * 87 104 0x02
+ * 88 98 0x02
+ * 89 110 0x01
+ * 90 104 0x01
+ * 91 98 0x01
+ * 92 110 0x00
+ * 93 104 0x00
+ * 94 98 0x00
+ * 95 93 0x00
+ * 96 88 0x00
+ * 97 83 0x00
+ * 98 78 0x00
+ */
+
+
+/**
+ * Sanity checks and default values for EEPROM regulatory levels.
+ * If EEPROM values fall outside MIN/MAX range, use default values.
+ *
+ * Regulatory limits refer to the maximum average txpower allowed by
+ * regulatory agencies in the geographies in which the device is meant
+ * to be operated. These limits are SKU-specific (i.e. geography-specific),
+ * and channel-specific; each channel has an individual regulatory limit
+ * listed in the EEPROM.
+ *
+ * Units are in half-dBm (i.e. "34" means 17 dBm).
+ */
#define IWL_TX_POWER_DEFAULT_REGULATORY_24 (34)
#define IWL_TX_POWER_DEFAULT_REGULATORY_52 (34)
#define IWL_TX_POWER_REGULATORY_MIN (0)
#define IWL_TX_POWER_REGULATORY_MAX (34)
+
+/**
+ * Sanity checks and default values for EEPROM saturation levels.
+ * If EEPROM values fall outside MIN/MAX range, use default values.
+ *
+ * Saturation is the highest level that the output power amplifier can produce
+ * without significant clipping distortion. This is a "peak" power level.
+ * Different types of modulation (i.e. various "rates", and OFDM vs. CCK)
+ * require differing amounts of backoff, relative to their average power output,
+ * in order to avoid clipping distortion.
+ *
+ * Driver must make sure that it is violating neither the saturation limit,
+ * nor the regulatory limit, when calculating Tx power settings for various
+ * rates.
+ *
+ * Units are in half-dBm (i.e. "38" means 19 dBm).
+ */
#define IWL_TX_POWER_DEFAULT_SATURATION_24 (38)
#define IWL_TX_POWER_DEFAULT_SATURATION_52 (38)
#define IWL_TX_POWER_SATURATION_MIN (20)
#define IWL_TX_POWER_SATURATION_MAX (50)
-/* dv *0.4 = dt; so that 5 degrees temperature diff equals
- * 12.5 in voltage diff */
-#define IWL_TX_TEMPERATURE_UPDATE_LIMIT 9
-
-#define IWL_INVALID_CHANNEL (0xffffffff)
-#define IWL_TX_POWER_REGITRY_BIT (2)
-
-#define MIN_IWL_TX_POWER_CALIB_DUR (100)
-#define IWL_CCK_FROM_OFDM_POWER_DIFF (-5)
-#define IWL_CCK_FROM_OFDM_INDEX_DIFF (9)
-
-/* Number of entries in the gain table */
-#define POWER_GAIN_NUM_ENTRIES 78
-#define TX_POW_MAX_SESSION_NUM 5
-/* timeout equivalent to 3 minutes */
-#define TX_IWL_TIMELIMIT_NOCALIB 1800000000
-
-/* Kedron TX_CALIB_STATES */
-#define IWL_TX_CALIB_STATE_SEND_TX 0x00000001
-#define IWL_TX_CALIB_WAIT_TX_RESPONSE 0x00000002
-#define IWL_TX_CALIB_ENABLED 0x00000004
-#define IWL_TX_CALIB_XVT_ON 0x00000008
-#define IWL_TX_CALIB_TEMPERATURE_CORRECT 0x00000010
-#define IWL_TX_CALIB_WORKING_WITH_XVT 0x00000020
-#define IWL_TX_CALIB_XVT_PERIODICAL 0x00000040
-
-#define NUM_IWL_TX_CALIB_SETTINS 5 /* Number of tx correction groups */
-
-#define IWL_MIN_POWER_IN_VP_TABLE 1 /* 0.5dBm multiplied by 2 */
-#define IWL_MAX_POWER_IN_VP_TABLE 40 /* 20dBm - multiplied by 2 (because
- * entries are for each 0.5dBm) */
-#define IWL_STEP_IN_VP_TABLE 1 /* 0.5dB - multiplied by 2 */
-#define IWL_NUM_POINTS_IN_VPTABLE \
- (1 + IWL_MAX_POWER_IN_VP_TABLE - IWL_MIN_POWER_IN_VP_TABLE)
-
-#define MIN_TX_GAIN_INDEX (0)
-#define MAX_TX_GAIN_INDEX_52GHZ (98)
-#define MIN_TX_GAIN_52GHZ (98)
-#define MAX_TX_GAIN_INDEX_24GHZ (98)
-#define MIN_TX_GAIN_24GHZ (98)
-#define MAX_TX_GAIN (0)
-
-/* First and last channels of all groups */
+/**
+ * Channel groups used for Tx Attenuation calibration (MIMO tx channel balance)
+ * and thermal Txpower calibration.
+ *
+ * When calculating txpower, driver must compensate for current device
+ * temperature; higher temperature requires higher gain. Driver must calculate
+ * current temperature (see "4965 temperature calculation"), then compare vs.
+ * factory calibration temperature in EEPROM; if current temperature is higher
+ * than factory temperature, driver must *increase* gain by proportions shown
+ * in table below. If current temperature is lower than factory, driver must
+ * *decrease* gain.
+ *
+ * Different frequency ranges require different compensation, as shown below.
+ */
+/* Group 0, 5.2 GHz ch 34-43: 4.5 degrees per 1/2 dB. */
#define CALIB_IWL_TX_ATTEN_GR1_FCH 34
#define CALIB_IWL_TX_ATTEN_GR1_LCH 43
+
+/* Group 1, 5.3 GHz ch 44-70: 4.0 degrees per 1/2 dB. */
#define CALIB_IWL_TX_ATTEN_GR2_FCH 44
#define CALIB_IWL_TX_ATTEN_GR2_LCH 70
+
+/* Group 2, 5.5 GHz ch 71-124: 4.0 degrees per 1/2 dB. */
#define CALIB_IWL_TX_ATTEN_GR3_FCH 71
#define CALIB_IWL_TX_ATTEN_GR3_LCH 124
+
+/* Group 3, 5.7 GHz ch 125-200: 4.0 degrees per 1/2 dB. */
#define CALIB_IWL_TX_ATTEN_GR4_FCH 125
#define CALIB_IWL_TX_ATTEN_GR4_LCH 200
+
+/* Group 4, 2.4 GHz all channels: 3.5 degrees per 1/2 dB. */
#define CALIB_IWL_TX_ATTEN_GR5_FCH 1
#define CALIB_IWL_TX_ATTEN_GR5_LCH 20
-
-union iwl_tx_power_dual_stream {
- struct {
- u8 radio_tx_gain[2];
- u8 dsp_predis_atten[2];
- } s;
- u32 dw;
+enum {
+ CALIB_CH_GROUP_1 = 0,
+ CALIB_CH_GROUP_2 = 1,
+ CALIB_CH_GROUP_3 = 2,
+ CALIB_CH_GROUP_4 = 3,
+ CALIB_CH_GROUP_5 = 4,
+ CALIB_CH_GROUP_MAX
};
/********************* END TXPOWER *****************************************/
-/* HT flags */
-#define RXON_FLG_CTRL_CHANNEL_LOC_POS (22)
-#define RXON_FLG_CTRL_CHANNEL_LOC_HI_MSK __constant_cpu_to_le32(0x1<<22)
-
-#define RXON_FLG_HT_OPERATING_MODE_POS (23)
-
-#define RXON_FLG_HT_PROT_MSK __constant_cpu_to_le32(0x1<<23)
-#define RXON_FLG_FAT_PROT_MSK __constant_cpu_to_le32(0x2<<23)
-
-#define RXON_FLG_CHANNEL_MODE_POS (25)
-#define RXON_FLG_CHANNEL_MODE_MSK __constant_cpu_to_le32(0x3<<25)
-#define RXON_FLG_CHANNEL_MODE_PURE_40_MSK __constant_cpu_to_le32(0x1<<25)
-#define RXON_FLG_CHANNEL_MODE_MIXED_MSK __constant_cpu_to_le32(0x2<<25)
-
-#define RXON_RX_CHAIN_DRIVER_FORCE_MSK __constant_cpu_to_le16(0x1<<0)
-#define RXON_RX_CHAIN_VALID_MSK __constant_cpu_to_le16(0x7<<1)
-#define RXON_RX_CHAIN_VALID_POS (1)
-#define RXON_RX_CHAIN_FORCE_SEL_MSK __constant_cpu_to_le16(0x7<<4)
-#define RXON_RX_CHAIN_FORCE_SEL_POS (4)
-#define RXON_RX_CHAIN_FORCE_MIMO_SEL_MSK __constant_cpu_to_le16(0x7<<7)
-#define RXON_RX_CHAIN_FORCE_MIMO_SEL_POS (7)
-#define RXON_RX_CHAIN_CNT_MSK __constant_cpu_to_le16(0x3<<10)
-#define RXON_RX_CHAIN_CNT_POS (10)
-#define RXON_RX_CHAIN_MIMO_CNT_MSK __constant_cpu_to_le16(0x3<<12)
-#define RXON_RX_CHAIN_MIMO_CNT_POS (12)
-#define RXON_RX_CHAIN_MIMO_FORCE_MSK __constant_cpu_to_le16(0x1<<14)
-#define RXON_RX_CHAIN_MIMO_FORCE_POS (14)
-
-
-#define MCS_DUP_6M_PLCP 0x20
-
-/* OFDM HT rate masks */
-/* ***************************************** */
-#define R_MCS_6M_MSK 0x1
-#define R_MCS_12M_MSK 0x2
-#define R_MCS_18M_MSK 0x4
-#define R_MCS_24M_MSK 0x8
-#define R_MCS_36M_MSK 0x10
-#define R_MCS_48M_MSK 0x20
-#define R_MCS_54M_MSK 0x40
-#define R_MCS_60M_MSK 0x80
-#define R_MCS_12M_DUAL_MSK 0x100
-#define R_MCS_24M_DUAL_MSK 0x200
-#define R_MCS_36M_DUAL_MSK 0x400
-#define R_MCS_48M_DUAL_MSK 0x800
-
-#define is_legacy(tbl) (((tbl) == LQ_G) || ((tbl) == LQ_A))
-#define is_siso(tbl) (((tbl) == LQ_SISO))
-#define is_mimo(tbl) (((tbl) == LQ_MIMO))
-#define is_Ht(tbl) (is_siso(tbl) || is_mimo(tbl))
-#define is_a_band(tbl) (((tbl) == LQ_A))
-#define is_g_and(tbl) (((tbl) == LQ_G))
-
+/****************************/
/* Flow Handler Definitions */
+/****************************/
-/**********************/
-/* Addresses */
-/**********************/
-
+/**
+ * This I/O area is directly read/writable by driver (e.g. Linux uses writel())
+ * Addresses are offsets from device's PCI hardware base address.
+ */
#define FH_MEM_LOWER_BOUND (0x1000)
#define FH_MEM_UPPER_BOUND (0x1EF0)
-#define IWL_FH_REGS_LOWER_BOUND (0x1000)
-#define IWL_FH_REGS_UPPER_BOUND (0x2000)
-
+/**
+ * Keep-Warm (KW) buffer base address.
+ *
+ * Driver must allocate a 4KByte buffer that is used by 4965 for keeping the
+ * host DRAM powered on (via dummy accesses to DRAM) to maintain low-latency
+ * DRAM access when 4965 is Txing or Rxing. The dummy accesses prevent host
+ * from going into a power-savings mode that would cause higher DRAM latency,
+ * and possible data over/under-runs, before all Tx/Rx is complete.
+ *
+ * Driver loads IWL_FH_KW_MEM_ADDR_REG with the physical address (bits 35:4)
+ * of the buffer, which must be 4K aligned. Once this is set up, the 4965
+ * automatically invokes keep-warm accesses when normal accesses might not
+ * be sufficient to maintain fast DRAM response.
+ *
+ * Bit fields:
+ * 31-0: Keep-warm buffer physical base address [35:4], must be 4K aligned
+ */
#define IWL_FH_KW_MEM_ADDR_REG (FH_MEM_LOWER_BOUND + 0x97C)
-/* CBBC Area - Circular buffers base address cache pointers table */
+
+/**
+ * TFD Circular Buffers Base (CBBC) addresses
+ *
+ * 4965 has 16 base pointer registers, one for each of 16 host-DRAM-resident
+ * circular buffers (CBs/queues) containing Transmit Frame Descriptors (TFDs)
+ * (see struct iwl_tfd_frame). These 16 pointer registers are offset by 0x04
+ * bytes from one another. Each TFD circular buffer in DRAM must be 256-byte
+ * aligned (address bits 0-7 must be 0).
+ *
+ * Bit fields in each pointer register:
+ * 27-0: TFD CB physical base address [35:8], must be 256-byte aligned
+ */
#define FH_MEM_CBBC_LOWER_BOUND (FH_MEM_LOWER_BOUND + 0x9D0)
#define FH_MEM_CBBC_UPPER_BOUND (FH_MEM_LOWER_BOUND + 0xA10)
-/* queues 0 - 15 */
+
+/* Find TFD CB base pointer for given queue (range 0-15). */
#define FH_MEM_CBBC_QUEUE(x) (FH_MEM_CBBC_LOWER_BOUND + (x) * 0x4)
-/* RSCSR Area */
+
+/**
+ * Rx SRAM Control and Status Registers (RSCSR)
+ *
+ * These registers provide handshake between driver and 4965 for the Rx queue
+ * (this queue handles *all* command responses, notifications, Rx data, etc.
+ * sent from 4965 uCode to host driver). Unlike Tx, there is only one Rx
+ * queue, and only one Rx DMA/FIFO channel. Also unlike Tx, which can
+ * concatenate up to 20 DRAM buffers to form a Tx frame, each Receive Buffer
+ * Descriptor (RBD) points to only one Rx Buffer (RB); there is a 1:1
+ * mapping between RBDs and RBs.
+ *
+ * Driver must allocate host DRAM memory for the following, and set the
+ * physical address of each into 4965 registers:
+ *
+ * 1) Receive Buffer Descriptor (RBD) circular buffer (CB), typically with 256
+ * entries (although any power of 2, up to 4096, is selectable by driver).
+ * Each entry (1 dword) points to a receive buffer (RB) of consistent size
+ * (typically 4K, although 8K or 16K are also selectable by driver).
+ * Driver sets up RB size and number of RBDs in the CB via Rx config
+ * register FH_MEM_RCSR_CHNL0_CONFIG_REG.
+ *
+ * Bit fields within one RBD:
+ * 27-0: Receive Buffer physical address bits [35:8], 256-byte aligned
+ *
+ * Driver sets physical address [35:8] of base of RBD circular buffer
+ * into FH_RSCSR_CHNL0_RBDCB_BASE_REG [27:0].
+ *
+ * 2) Rx status buffer, 8 bytes, in which 4965 indicates which Rx Buffers
+ * (RBs) have been filled, via a "write pointer", actually the index of
+ * the RB's corresponding RBD within the circular buffer. Driver sets
+ * physical address [35:4] into FH_RSCSR_CHNL0_STTS_WPTR_REG [31:0].
+ *
+ * Bit fields in lower dword of Rx status buffer (upper dword not used
+ * by driver; see struct iwl4965_shared, val0):
+ * 31-12: Not used by driver
+ * 11- 0: Index of last filled Rx buffer descriptor
+ * (4965 writes, driver reads this value)
+ *
+ * As the driver prepares Receive Buffers (RBs) for 4965 to fill, driver must
+ * enter pointers to these RBs into contiguous RBD circular buffer entries,
+ * and update the 4965's "write" index register, FH_RSCSR_CHNL0_RBDCB_WPTR_REG.
+ *
+ * This "write" index corresponds to the *next* RBD that the driver will make
+ * available, i.e. one RBD past the tail of the ready-to-fill RBDs within
+ * the circular buffer. This value should initially be 0 (before preparing any
+ * RBs), should be 8 after preparing the first 8 RBs (for example), and must
+ * wrap back to 0 at the end of the circular buffer (but don't wrap before
+ * "read" index has advanced past 1! See below).
+ * NOTE: 4965 EXPECTS THE WRITE INDEX TO BE INCREMENTED IN MULTIPLES OF 8.
+ *
+ * As the 4965 fills RBs (referenced from contiguous RBDs within the circular
+ * buffer), it updates the Rx status buffer in host DRAM, 2) described above,
+ * to tell the driver the index of the latest filled RBD. The driver must
+ * read this "read" index from DRAM after receiving an Rx interrupt from 4965.
+ *
+ * The driver must also internally keep track of a third index, which is the
+ * next RBD to process. When receiving an Rx interrupt, driver should process
+ * all filled but unprocessed RBs up to, but not including, the RB
+ * corresponding to the "read" index. For example, if "read" index becomes "1",
+ * driver may process the RB pointed to by RBD 0. Depending on volume of
+ * traffic, there may be many RBs to process.
+ *
+ * If read index == write index, 4965 thinks there is no room to put new data.
+ * Due to this, the maximum number of filled RBs is 255, instead of 256. To
+ * be safe, make sure that there is a gap of at least 2 RBDs between "write"
+ * and "read" indexes; that is, make sure that there are no more than 254
+ * buffers waiting to be filled.
+ */
#define FH_MEM_RSCSR_LOWER_BOUND (FH_MEM_LOWER_BOUND + 0xBC0)
#define FH_MEM_RSCSR_UPPER_BOUND (FH_MEM_LOWER_BOUND + 0xC00)
#define FH_MEM_RSCSR_CHNL0 (FH_MEM_RSCSR_LOWER_BOUND)
+/**
+ * Physical base address of 8-byte Rx Status buffer.
+ * Bit fields:
+ * 31-0: Rx status buffer physical base address [35:4], must 16-byte aligned.
+ */
#define FH_RSCSR_CHNL0_STTS_WPTR_REG (FH_MEM_RSCSR_CHNL0)
+
+/**
+ * Physical base address of Rx Buffer Descriptor Circular Buffer.
+ * Bit fields:
+ * 27-0: RBD CD physical base address [35:8], must be 256-byte aligned.
+ */
#define FH_RSCSR_CHNL0_RBDCB_BASE_REG (FH_MEM_RSCSR_CHNL0 + 0x004)
+
+/**
+ * Rx write pointer (index, really!).
+ * Bit fields:
+ * 11-0: Index of driver's most recent prepared-to-be-filled RBD, + 1.
+ * NOTE: For 256-entry circular buffer, use only bits [7:0].
+ */
#define FH_RSCSR_CHNL0_RBDCB_WPTR_REG (FH_MEM_RSCSR_CHNL0 + 0x008)
+#define FH_RSCSR_CHNL0_WPTR (FH_RSCSR_CHNL0_RBDCB_WPTR_REG)
+
-/* RCSR Area - Registers address map */
+/**
+ * Rx Config/Status Registers (RCSR)
+ * Rx Config Reg for channel 0 (only channel used)
+ *
+ * Driver must initialize FH_MEM_RCSR_CHNL0_CONFIG_REG as follows for
+ * normal operation (see bit fields).
+ *
+ * Clearing FH_MEM_RCSR_CHNL0_CONFIG_REG to 0 turns off Rx DMA.
+ * Driver should poll FH_MEM_RSSR_RX_STATUS_REG for
+ * FH_RSSR_CHNL0_RX_STATUS_CHNL_IDLE (bit 24) before continuing.
+ *
+ * Bit fields:
+ * 31-30: Rx DMA channel enable: '00' off/pause, '01' pause at end of frame,
+ * '10' operate normally
+ * 29-24: reserved
+ * 23-20: # RBDs in circular buffer = 2^value; use "8" for 256 RBDs (normal),
+ * min "5" for 32 RBDs, max "12" for 4096 RBDs.
+ * 19-18: reserved
+ * 17-16: size of each receive buffer; '00' 4K (normal), '01' 8K,
+ * '10' 12K, '11' 16K.
+ * 15-14: reserved
+ * 13-12: IRQ destination; '00' none, '01' host driver (normal operation)
+ * 11- 4: timeout for closing Rx buffer and interrupting host (units 32 usec)
+ * typical value 0x10 (about 1/2 msec)
+ * 3- 0: reserved
+ */
#define FH_MEM_RCSR_LOWER_BOUND (FH_MEM_LOWER_BOUND + 0xC00)
#define FH_MEM_RCSR_UPPER_BOUND (FH_MEM_LOWER_BOUND + 0xCC0)
#define FH_MEM_RCSR_CHNL0 (FH_MEM_RCSR_LOWER_BOUND)
#define FH_MEM_RCSR_CHNL0_CONFIG_REG (FH_MEM_RCSR_CHNL0)
-/* RSSR Area - Rx shared ctrl & status registers */
+#define FH_RCSR_CHNL0_RX_CONFIG_RB_TIMEOUT_MASK (0x00000FF0) /* bit 4-11 */
+#define FH_RCSR_CHNL0_RX_CONFIG_IRQ_DEST_MASK (0x00001000) /* bit 12 */
+#define FH_RCSR_CHNL0_RX_CONFIG_SINGLE_FRAME_MASK (0x00008000) /* bit 15 */
+#define FH_RCSR_CHNL0_RX_CONFIG_RB_SIZE_MASK (0x00030000) /* bits 16-17 */
+#define FH_RCSR_CHNL0_RX_CONFIG_RBDBC_SIZE_MASK (0x00F00000) /* bits 20-23 */
+#define FH_RCSR_CHNL0_RX_CONFIG_DMA_CHNL_EN_MASK (0xC0000000) /* bits 30-31 */
+
+#define FH_RCSR_RX_CONFIG_RBDCB_SIZE_BITSHIFT (20)
+#define FH_RCSR_RX_CONFIG_REG_IRQ_RBTH_BITSHIFT (4)
+#define RX_RB_TIMEOUT (0x10)
+
+#define FH_RCSR_RX_CONFIG_CHNL_EN_PAUSE_VAL (0x00000000)
+#define FH_RCSR_RX_CONFIG_CHNL_EN_PAUSE_EOF_VAL (0x40000000)
+#define FH_RCSR_RX_CONFIG_CHNL_EN_ENABLE_VAL (0x80000000)
+
+#define FH_RCSR_RX_CONFIG_REG_VAL_RB_SIZE_4K (0x00000000)
+#define FH_RCSR_RX_CONFIG_REG_VAL_RB_SIZE_8K (0x00010000)
+#define FH_RCSR_RX_CONFIG_REG_VAL_RB_SIZE_12K (0x00020000)
+#define FH_RCSR_RX_CONFIG_REG_VAL_RB_SIZE_16K (0x00030000)
+
+#define FH_RCSR_CHNL0_RX_CONFIG_IRQ_DEST_NO_INT_VAL (0x00000000)
+#define FH_RCSR_CHNL0_RX_CONFIG_IRQ_DEST_INT_HOST_VAL (0x00001000)
+
+
+/**
+ * Rx Shared Status Registers (RSSR)
+ *
+ * After stopping Rx DMA channel (writing 0 to FH_MEM_RCSR_CHNL0_CONFIG_REG),
+ * driver must poll FH_MEM_RSSR_RX_STATUS_REG until Rx channel is idle.
+ *
+ * Bit fields:
+ * 24: 1 = Channel 0 is idle
+ *
+ * FH_MEM_RSSR_SHARED_CTRL_REG and FH_MEM_RSSR_RX_ENABLE_ERR_IRQ2DRV contain
+ * default values that should not be altered by the driver.
+ */
#define FH_MEM_RSSR_LOWER_BOUND (FH_MEM_LOWER_BOUND + 0xC40)
#define FH_MEM_RSSR_UPPER_BOUND (FH_MEM_LOWER_BOUND + 0xD00)
+
#define FH_MEM_RSSR_SHARED_CTRL_REG (FH_MEM_RSSR_LOWER_BOUND)
#define FH_MEM_RSSR_RX_STATUS_REG (FH_MEM_RSSR_LOWER_BOUND + 0x004)
#define FH_MEM_RSSR_RX_ENABLE_ERR_IRQ2DRV (FH_MEM_RSSR_LOWER_BOUND + 0x008)
-/* TCSR */
-#define IWL_FH_TCSR_LOWER_BOUND (IWL_FH_REGS_LOWER_BOUND + 0xD00)
-#define IWL_FH_TCSR_UPPER_BOUND (IWL_FH_REGS_LOWER_BOUND + 0xE60)
+#define FH_RSSR_CHNL0_RX_STATUS_CHNL_IDLE (0x01000000)
+
-#define IWL_FH_TCSR_CHNL_NUM (7)
+/**
+ * Transmit DMA Channel Control/Status Registers (TCSR)
+ *
+ * 4965 has one configuration register for each of 8 Tx DMA/FIFO channels
+ * supported in hardware (don't confuse these with the 16 Tx queues in DRAM,
+ * which feed the DMA/FIFO channels); config regs are separated by 0x20 bytes.
+ *
+ * To use a Tx DMA channel, driver must initialize its
+ * IWL_FH_TCSR_CHNL_TX_CONFIG_REG(chnl) with:
+ *
+ * IWL_FH_TCSR_TX_CONFIG_REG_VAL_DMA_CHNL_ENABLE |
+ * IWL_FH_TCSR_TX_CONFIG_REG_VAL_DMA_CREDIT_ENABLE_VAL
+ *
+ * All other bits should be 0.
+ *
+ * Bit fields:
+ * 31-30: Tx DMA channel enable: '00' off/pause, '01' pause at end of frame,
+ * '10' operate normally
+ * 29- 4: Reserved, set to "0"
+ * 3: Enable internal DMA requests (1, normal operation), disable (0)
+ * 2- 0: Reserved, set to "0"
+ */
+#define IWL_FH_TCSR_LOWER_BOUND (FH_MEM_LOWER_BOUND + 0xD00)
+#define IWL_FH_TCSR_UPPER_BOUND (FH_MEM_LOWER_BOUND + 0xE60)
+
+/* Find Control/Status reg for given Tx DMA/FIFO channel */
#define IWL_FH_TCSR_CHNL_TX_CONFIG_REG(_chnl) \
(IWL_FH_TCSR_LOWER_BOUND + 0x20 * _chnl)
-/* TSSR Area - Tx shared status registers */
-/* TSSR */
-#define IWL_FH_TSSR_LOWER_BOUND (IWL_FH_REGS_LOWER_BOUND + 0xEA0)
-#define IWL_FH_TSSR_UPPER_BOUND (IWL_FH_REGS_LOWER_BOUND + 0xEC0)
-
-#define IWL_FH_TSSR_TX_MSG_CONFIG_REG (IWL_FH_TSSR_LOWER_BOUND + 0x008)
-#define IWL_FH_TSSR_TX_STATUS_REG (IWL_FH_TSSR_LOWER_BOUND + 0x010)
-
-#define IWL_FH_TSSR_TX_MSG_CONFIG_REG_VAL_SNOOP_RD_TXPD_ON (0xFF000000)
-#define IWL_FH_TSSR_TX_MSG_CONFIG_REG_VAL_ORDER_RD_TXPD_ON (0x00FF0000)
+#define IWL_FH_TCSR_TX_CONFIG_REG_VAL_DMA_CREDIT_DISABLE_VAL (0x00000000)
+#define IWL_FH_TCSR_TX_CONFIG_REG_VAL_DMA_CREDIT_ENABLE_VAL (0x00000008)
-#define IWL_FH_TSSR_TX_MSG_CONFIG_REG_VAL_MAX_FRAG_SIZE_64B (0x00000000)
-#define IWL_FH_TSSR_TX_MSG_CONFIG_REG_VAL_MAX_FRAG_SIZE_128B (0x00000400)
-#define IWL_FH_TSSR_TX_MSG_CONFIG_REG_VAL_MAX_FRAG_SIZE_256B (0x00000800)
-#define IWL_FH_TSSR_TX_MSG_CONFIG_REG_VAL_MAX_FRAG_SIZE_512B (0x00000C00)
+#define IWL_FH_TCSR_TX_CONFIG_REG_VAL_DMA_CHNL_PAUSE (0x00000000)
+#define IWL_FH_TCSR_TX_CONFIG_REG_VAL_DMA_CHNL_PAUSE_EOF (0x40000000)
+#define IWL_FH_TCSR_TX_CONFIG_REG_VAL_DMA_CHNL_ENABLE (0x80000000)
-#define IWL_FH_TSSR_TX_MSG_CONFIG_REG_VAL_SNOOP_RD_TFD_ON (0x00000100)
-#define IWL_FH_TSSR_TX_MSG_CONFIG_REG_VAL_ORDER_RD_CBB_ON (0x00000080)
+/**
+ * Tx Shared Status Registers (TSSR)
+ *
+ * After stopping Tx DMA channel (writing 0 to
+ * IWL_FH_TCSR_CHNL_TX_CONFIG_REG(chnl)), driver must poll
+ * IWL_FH_TSSR_TX_STATUS_REG until selected Tx channel is idle
+ * (channel's buffers empty | no pending requests).
+ *
+ * Bit fields:
+ * 31-24: 1 = Channel buffers empty (channel 7:0)
+ * 23-16: 1 = No pending requests (channel 7:0)
+ */
+#define IWL_FH_TSSR_LOWER_BOUND (FH_MEM_LOWER_BOUND + 0xEA0)
+#define IWL_FH_TSSR_UPPER_BOUND (FH_MEM_LOWER_BOUND + 0xEC0)
-#define IWL_FH_TSSR_TX_MSG_CONFIG_REG_VAL_ORDER_RSP_WAIT_TH (0x00000020)
-#define IWL_FH_TSSR_TX_MSG_CONFIG_REG_VAL_RSP_WAIT_TH (0x00000005)
+#define IWL_FH_TSSR_TX_STATUS_REG (IWL_FH_TSSR_LOWER_BOUND + 0x010)
#define IWL_FH_TSSR_TX_STATUS_REG_BIT_BUFS_EMPTY(_chnl) \
((1 << (_chnl)) << 24)
@@ -341,147 +1558,347 @@ union iwl_tx_power_dual_stream {
(IWL_FH_TSSR_TX_STATUS_REG_BIT_BUFS_EMPTY(_chnl) | \
IWL_FH_TSSR_TX_STATUS_REG_BIT_NO_PEND_REQ(_chnl))
-/* TCSR: tx_config register values */
-#define IWL_FH_TCSR_TX_CONFIG_REG_VAL_MSG_MODE_TXF (0x00000000)
-#define IWL_FH_TCSR_TX_CONFIG_REG_VAL_MSG_MODE_DRIVER (0x00000001)
-#define IWL_FH_TCSR_TX_CONFIG_REG_VAL_MSG_MODE_ARC (0x00000002)
-
-#define IWL_FH_TCSR_TX_CONFIG_REG_VAL_DMA_CREDIT_DISABLE_VAL (0x00000000)
-#define IWL_FH_TCSR_TX_CONFIG_REG_VAL_DMA_CREDIT_ENABLE_VAL (0x00000008)
-
-#define IWL_FH_TCSR_TX_CONFIG_REG_VAL_CIRQ_HOST_NOINT (0x00000000)
-#define IWL_FH_TCSR_TX_CONFIG_REG_VAL_CIRQ_HOST_ENDTFD (0x00100000)
-#define IWL_FH_TCSR_TX_CONFIG_REG_VAL_CIRQ_HOST_IFTFD (0x00200000)
-
-#define IWL_FH_TCSR_TX_CONFIG_REG_VAL_CIRQ_RTC_NOINT (0x00000000)
-#define IWL_FH_TCSR_TX_CONFIG_REG_VAL_CIRQ_RTC_ENDTFD (0x00400000)
-#define IWL_FH_TCSR_TX_CONFIG_REG_VAL_CIRQ_RTC_IFTFD (0x00800000)
-#define IWL_FH_TCSR_TX_CONFIG_REG_VAL_DMA_CHNL_PAUSE (0x00000000)
-#define IWL_FH_TCSR_TX_CONFIG_REG_VAL_DMA_CHNL_PAUSE_EOF (0x40000000)
-#define IWL_FH_TCSR_TX_CONFIG_REG_VAL_DMA_CHNL_ENABLE (0x80000000)
-
-#define IWL_FH_TCSR_CHNL_TX_BUF_STS_REG_VAL_TFDB_EMPTY (0x00000000)
-#define IWL_FH_TCSR_CHNL_TX_BUF_STS_REG_VAL_TFDB_WAIT (0x00002000)
-#define IWL_FH_TCSR_CHNL_TX_BUF_STS_REG_VAL_TFDB_VALID (0x00000003)
-
-#define IWL_FH_TCSR_CHNL_TX_BUF_STS_REG_BIT_TFDB_WPTR (0x00000001)
-
-#define IWL_FH_TCSR_CHNL_TX_BUF_STS_REG_POS_TB_NUM (20)
-#define IWL_FH_TCSR_CHNL_TX_BUF_STS_REG_POS_TB_IDX (12)
-
-/* RCSR: channel 0 rx_config register defines */
-#define FH_RCSR_CHNL0_RX_CONFIG_DMA_CHNL_EN_MASK (0xC0000000) /* bits 30-31 */
-#define FH_RCSR_CHNL0_RX_CONFIG_RBDBC_SIZE_MASK (0x00F00000) /* bits 20-23 */
-#define FH_RCSR_CHNL0_RX_CONFIG_RB_SIZE_MASK (0x00030000) /* bits 16-17 */
-#define FH_RCSR_CHNL0_RX_CONFIG_SINGLE_FRAME_MASK (0x00008000) /* bit 15 */
-#define FH_RCSR_CHNL0_RX_CONFIG_IRQ_DEST_MASK (0x00001000) /* bit 12 */
-#define FH_RCSR_CHNL0_RX_CONFIG_RB_TIMEOUT_MASK (0x00000FF0) /* bit 4-11 */
-
-#define FH_RCSR_RX_CONFIG_RBDCB_SIZE_BITSHIFT (20)
-#define FH_RCSR_RX_CONFIG_RB_SIZE_BITSHIFT (16)
-
-/* RCSR: rx_config register values */
-#define FH_RCSR_RX_CONFIG_CHNL_EN_PAUSE_VAL (0x00000000)
-#define FH_RCSR_RX_CONFIG_CHNL_EN_PAUSE_EOF_VAL (0x40000000)
-#define FH_RCSR_RX_CONFIG_CHNL_EN_ENABLE_VAL (0x80000000)
-
-#define IWL_FH_RCSR_RX_CONFIG_REG_VAL_RB_SIZE_4K (0x00000000)
-
-/* RCSR channel 0 config register values */
-#define FH_RCSR_CHNL0_RX_CONFIG_IRQ_DEST_NO_INT_VAL (0x00000000)
-#define FH_RCSR_CHNL0_RX_CONFIG_IRQ_DEST_INT_HOST_VAL (0x00001000)
-
-/* RSCSR: defs used in normal mode */
-#define FH_RSCSR_CHNL0_RBDCB_WPTR_MASK (0x00000FFF) /* bits 0-11 */
+/********************* START TX SCHEDULER *************************************/
+/**
+ * 4965 Tx Scheduler
+ *
+ * The Tx Scheduler selects the next frame to be transmitted, chosing TFDs
+ * (Transmit Frame Descriptors) from up to 16 circular Tx queues resident in
+ * host DRAM. It steers each frame's Tx command (which contains the frame
+ * data) into one of up to 7 prioritized Tx DMA FIFO channels within the
+ * device. A queue maps to only one (selectable by driver) Tx DMA channel,
+ * but one DMA channel may take input from several queues.
+ *
+ * Tx DMA channels have dedicated purposes. For 4965, they are used as follows:
+ *
+ * 0 -- EDCA BK (background) frames, lowest priority
+ * 1 -- EDCA BE (best effort) frames, normal priority
+ * 2 -- EDCA VI (video) frames, higher priority
+ * 3 -- EDCA VO (voice) and management frames, highest priority
+ * 4 -- Commands (e.g. RXON, etc.)
+ * 5 -- HCCA short frames
+ * 6 -- HCCA long frames
+ * 7 -- not used by driver (device-internal only)
+ *
+ * Driver should normally map queues 0-6 to Tx DMA/FIFO channels 0-6.
+ * In addition, driver can map queues 7-15 to Tx DMA/FIFO channels 0-3 to
+ * support 11n aggregation via EDCA DMA channels.
+ *
+ * The driver sets up each queue to work in one of two modes:
+ *
+ * 1) Scheduler-Ack, in which the scheduler automatically supports a
+ * block-ack (BA) window of up to 64 TFDs. In this mode, each queue
+ * contains TFDs for a unique combination of Recipient Address (RA)
+ * and Traffic Identifier (TID), that is, traffic of a given
+ * Quality-Of-Service (QOS) priority, destined for a single station.
+ *
+ * In scheduler-ack mode, the scheduler keeps track of the Tx status of
+ * each frame within the BA window, including whether it's been transmitted,
+ * and whether it's been acknowledged by the receiving station. The device
+ * automatically processes block-acks received from the receiving STA,
+ * and reschedules un-acked frames to be retransmitted (successful
+ * Tx completion may end up being out-of-order).
+ *
+ * The driver must maintain the queue's Byte Count table in host DRAM
+ * (struct iwl4965_sched_queue_byte_cnt_tbl) for this mode.
+ * This mode does not support fragmentation.
+ *
+ * 2) FIFO (a.k.a. non-Scheduler-ACK), in which each TFD is processed in order.
+ * The device may automatically retry Tx, but will retry only one frame
+ * at a time, until receiving ACK from receiving station, or reaching
+ * retry limit and giving up.
+ *
+ * The command queue (#4) must use this mode!
+ * This mode does not require use of the Byte Count table in host DRAM.
+ *
+ * Driver controls scheduler operation via 3 means:
+ * 1) Scheduler registers
+ * 2) Shared scheduler data base in internal 4956 SRAM
+ * 3) Shared data in host DRAM
+ *
+ * Initialization:
+ *
+ * When loading, driver should allocate memory for:
+ * 1) 16 TFD circular buffers, each with space for (typically) 256 TFDs.
+ * 2) 16 Byte Count circular buffers in 16 KBytes contiguous memory
+ * (1024 bytes for each queue).
+ *
+ * After receiving "Alive" response from uCode, driver must initialize
+ * the scheduler (especially for queue #4, the command queue, otherwise
+ * the driver can't issue commands!):
+ */
+
+/**
+ * Max Tx window size is the max number of contiguous TFDs that the scheduler
+ * can keep track of at one time when creating block-ack chains of frames.
+ * Note that "64" matches the number of ack bits in a block-ack packet.
+ * Driver should use SCD_WIN_SIZE and SCD_FRAME_LIMIT values to initialize
+ * SCD_CONTEXT_QUEUE_OFFSET(x) values.
+ */
#define SCD_WIN_SIZE 64
#define SCD_FRAME_LIMIT 64
-/* memory mapped registers */
+/* SCD registers are internal, must be accessed via HBUS_TARG_PRPH regs */
#define SCD_START_OFFSET 0xa02c00
+/*
+ * 4965 tells driver SRAM address for internal scheduler structs via this reg.
+ * Value is valid only after "Alive" response from uCode.
+ */
#define SCD_SRAM_BASE_ADDR (SCD_START_OFFSET + 0x0)
+
+/*
+ * Driver may need to update queue-empty bits after changing queue's
+ * write and read pointers (indexes) during (re-)initialization (i.e. when
+ * scheduler is not tracking what's happening).
+ * Bit fields:
+ * 31-16: Write mask -- 1: update empty bit, 0: don't change empty bit
+ * 15-00: Empty state, one for each queue -- 1: empty, 0: non-empty
+ * NOTE: This register is not used by Linux driver.
+ */
#define SCD_EMPTY_BITS (SCD_START_OFFSET + 0x4)
+
+/*
+ * Physical base address of array of byte count (BC) circular buffers (CBs).
+ * Each Tx queue has a BC CB in host DRAM to support Scheduler-ACK mode.
+ * This register points to BC CB for queue 0, must be on 1024-byte boundary.
+ * Others are spaced by 1024 bytes.
+ * Each BC CB is 2 bytes * (256 + 64) = 740 bytes, followed by 384 bytes pad.
+ * (Index into a queue's BC CB) = (index into queue's TFD CB) = (SSN & 0xff).
+ * Bit fields:
+ * 25-00: Byte Count CB physical address [35:10], must be 1024-byte aligned.
+ */
#define SCD_DRAM_BASE_ADDR (SCD_START_OFFSET + 0x10)
-#define SCD_AIT (SCD_START_OFFSET + 0x18)
+
+/*
+ * Enables any/all Tx DMA/FIFO channels.
+ * Scheduler generates requests for only the active channels.
+ * Set this to 0xff to enable all 8 channels (normal usage).
+ * Bit fields:
+ * 7- 0: Enable (1), disable (0), one bit for each channel 0-7
+ */
#define SCD_TXFACT (SCD_START_OFFSET + 0x1c)
+
+/* Mask to enable contiguous Tx DMA/FIFO channels between "lo" and "hi". */
+#define SCD_TXFACT_REG_TXFIFO_MASK(lo, hi) \
+ ((1 << (hi)) | ((1 << (hi)) - (1 << (lo))))
+
+/*
+ * Queue (x) Write Pointers (indexes, really!), one for each Tx queue.
+ * Initialized and updated by driver as new TFDs are added to queue.
+ * NOTE: If using Block Ack, index must correspond to frame's
+ * Start Sequence Number; index = (SSN & 0xff)
+ * NOTE: Alternative to HBUS_TARG_WRPTR, which is what Linux driver uses?
+ */
#define SCD_QUEUE_WRPTR(x) (SCD_START_OFFSET + 0x24 + (x) * 4)
-#define SCD_QUEUE_RDPTR(x) (SCD_START_OFFSET + 0x64 + (x) * 4)
-#define SCD_SETQUEUENUM (SCD_START_OFFSET + 0xa4)
-#define SCD_SET_TXSTAT_TXED (SCD_START_OFFSET + 0xa8)
-#define SCD_SET_TXSTAT_DONE (SCD_START_OFFSET + 0xac)
-#define SCD_SET_TXSTAT_NOT_SCHD (SCD_START_OFFSET + 0xb0)
-#define SCD_DECREASE_CREDIT (SCD_START_OFFSET + 0xb4)
-#define SCD_DECREASE_SCREDIT (SCD_START_OFFSET + 0xb8)
-#define SCD_LOAD_CREDIT (SCD_START_OFFSET + 0xbc)
-#define SCD_LOAD_SCREDIT (SCD_START_OFFSET + 0xc0)
-#define SCD_BAR (SCD_START_OFFSET + 0xc4)
-#define SCD_BAR_DW0 (SCD_START_OFFSET + 0xc8)
-#define SCD_BAR_DW1 (SCD_START_OFFSET + 0xcc)
-#define SCD_QUEUECHAIN_SEL (SCD_START_OFFSET + 0xd0)
-#define SCD_QUERY_REQ (SCD_START_OFFSET + 0xd8)
-#define SCD_QUERY_RES (SCD_START_OFFSET + 0xdc)
-#define SCD_PENDING_FRAMES (SCD_START_OFFSET + 0xe0)
-#define SCD_INTERRUPT_MASK (SCD_START_OFFSET + 0xe4)
-#define SCD_INTERRUPT_THRESHOLD (SCD_START_OFFSET + 0xe8)
-#define SCD_QUERY_MIN_FRAME_SIZE (SCD_START_OFFSET + 0x100)
-#define SCD_QUEUE_STATUS_BITS(x) (SCD_START_OFFSET + 0x104 + (x) * 4)
-/* SRAM structures */
-#define SCD_CONTEXT_DATA_OFFSET 0x380
-#define SCD_TX_STTS_BITMAP_OFFSET 0x400
-#define SCD_TRANSLATE_TBL_OFFSET 0x500
-#define SCD_CONTEXT_QUEUE_OFFSET(x) (SCD_CONTEXT_DATA_OFFSET + ((x) * 8))
-#define SCD_TRANSLATE_TBL_OFFSET_QUEUE(x) \
- ((SCD_TRANSLATE_TBL_OFFSET + ((x) * 2)) & 0xfffffffc)
+/*
+ * Queue (x) Read Pointers (indexes, really!), one for each Tx queue.
+ * For FIFO mode, index indicates next frame to transmit.
+ * For Scheduler-ACK mode, index indicates first frame in Tx window.
+ * Initialized by driver, updated by scheduler.
+ */
+#define SCD_QUEUE_RDPTR(x) (SCD_START_OFFSET + 0x64 + (x) * 4)
-#define SCD_TXFACT_REG_TXFIFO_MASK(lo, hi) \
- ((1<<(hi))|((1<<(hi))-(1<<(lo))))
+/*
+ * Select which queues work in chain mode (1) vs. not (0).
+ * Use chain mode to build chains of aggregated frames.
+ * Bit fields:
+ * 31-16: Reserved
+ * 15-00: Mode, one bit for each queue -- 1: Chain mode, 0: one-at-a-time
+ * NOTE: If driver sets up queue for chain mode, it should be also set up
+ * Scheduler-ACK mode as well, via SCD_QUEUE_STATUS_BITS(x).
+ */
+#define SCD_QUEUECHAIN_SEL (SCD_START_OFFSET + 0xd0)
+/*
+ * Select which queues interrupt driver when scheduler increments
+ * a queue's read pointer (index).
+ * Bit fields:
+ * 31-16: Reserved
+ * 15-00: Interrupt enable, one bit for each queue -- 1: enabled, 0: disabled
+ * NOTE: This functionality is apparently a no-op; driver relies on interrupts
+ * from Rx queue to read Tx command responses and update Tx queues.
+ */
+#define SCD_INTERRUPT_MASK (SCD_START_OFFSET + 0xe4)
-#define SCD_MODE_REG_BIT_SEARCH_MODE (1<<0)
-#define SCD_MODE_REG_BIT_SBYP_MODE (1<<1)
+/*
+ * Queue search status registers. One for each queue.
+ * Sets up queue mode and assigns queue to Tx DMA channel.
+ * Bit fields:
+ * 19-10: Write mask/enable bits for bits 0-9
+ * 9: Driver should init to "0"
+ * 8: Scheduler-ACK mode (1), non-Scheduler-ACK (i.e. FIFO) mode (0).
+ * Driver should init to "1" for aggregation mode, or "0" otherwise.
+ * 7-6: Driver should init to "0"
+ * 5: Window Size Left; indicates whether scheduler can request
+ * another TFD, based on window size, etc. Driver should init
+ * this bit to "1" for aggregation mode, or "0" for non-agg.
+ * 4-1: Tx FIFO to use (range 0-7).
+ * 0: Queue is active (1), not active (0).
+ * Other bits should be written as "0"
+ *
+ * NOTE: If enabling Scheduler-ACK mode, chain mode should also be enabled
+ * via SCD_QUEUECHAIN_SEL.
+ */
+#define SCD_QUEUE_STATUS_BITS(x) (SCD_START_OFFSET + 0x104 + (x) * 4)
-#define SCD_TXFIFO_POS_TID (0)
-#define SCD_TXFIFO_POS_RA (4)
+/* Bit field positions */
#define SCD_QUEUE_STTS_REG_POS_ACTIVE (0)
#define SCD_QUEUE_STTS_REG_POS_TXF (1)
#define SCD_QUEUE_STTS_REG_POS_WSL (5)
#define SCD_QUEUE_STTS_REG_POS_SCD_ACK (8)
+
+/* Write masks */
#define SCD_QUEUE_STTS_REG_POS_SCD_ACT_EN (10)
#define SCD_QUEUE_STTS_REG_MSK (0x0007FC00)
-#define SCD_QUEUE_RA_TID_MAP_RATID_MSK (0x01FF)
+/**
+ * 4965 internal SRAM structures for scheduler, shared with driver ...
+ *
+ * Driver should clear and initialize the following areas after receiving
+ * "Alive" response from 4965 uCode, i.e. after initial
+ * uCode load, or after a uCode load done for error recovery:
+ *
+ * SCD_CONTEXT_DATA_OFFSET (size 128 bytes)
+ * SCD_TX_STTS_BITMAP_OFFSET (size 256 bytes)
+ * SCD_TRANSLATE_TBL_OFFSET (size 32 bytes)
+ *
+ * Driver accesses SRAM via HBUS_TARG_MEM_* registers.
+ * Driver reads base address of this scheduler area from SCD_SRAM_BASE_ADDR.
+ * All OFFSET values must be added to this base address.
+ */
+
+/*
+ * Queue context. One 8-byte entry for each of 16 queues.
+ *
+ * Driver should clear this entire area (size 0x80) to 0 after receiving
+ * "Alive" notification from uCode. Additionally, driver should init
+ * each queue's entry as follows:
+ *
+ * LS Dword bit fields:
+ * 0-06: Max Tx window size for Scheduler-ACK. Driver should init to 64.
+ *
+ * MS Dword bit fields:
+ * 16-22: Frame limit. Driver should init to 10 (0xa).
+ *
+ * Driver should init all other bits to 0.
+ *
+ * Init must be done after driver receives "Alive" response from 4965 uCode,
+ * and when setting up queue for aggregation.
+ */
+#define SCD_CONTEXT_DATA_OFFSET 0x380
+#define SCD_CONTEXT_QUEUE_OFFSET(x) (SCD_CONTEXT_DATA_OFFSET + ((x) * 8))
#define SCD_QUEUE_CTX_REG1_WIN_SIZE_POS (0)
#define SCD_QUEUE_CTX_REG1_WIN_SIZE_MSK (0x0000007F)
-#define SCD_QUEUE_CTX_REG1_CREDIT_POS (8)
-#define SCD_QUEUE_CTX_REG1_CREDIT_MSK (0x00FFFF00)
-#define SCD_QUEUE_CTX_REG1_SUPER_CREDIT_POS (24)
-#define SCD_QUEUE_CTX_REG1_SUPER_CREDIT_MSK (0xFF000000)
#define SCD_QUEUE_CTX_REG2_FRAME_LIMIT_POS (16)
#define SCD_QUEUE_CTX_REG2_FRAME_LIMIT_MSK (0x007F0000)
-#define CSR_HW_IF_CONFIG_REG_BIT_KEDRON_R (0x00000010)
-#define CSR_HW_IF_CONFIG_REG_MSK_BOARD_VER (0x00000C00)
-#define CSR_HW_IF_CONFIG_REG_BIT_MAC_SI (0x00000100)
-#define CSR_HW_IF_CONFIG_REG_BIT_RADIO_SI (0x00000200)
+/*
+ * Tx Status Bitmap
+ *
+ * Driver should clear this entire area (size 0x100) to 0 after receiving
+ * "Alive" notification from uCode. Area is used only by device itself;
+ * no other support (besides clearing) is required from driver.
+ */
+#define SCD_TX_STTS_BITMAP_OFFSET 0x400
-static inline u8 iwl_hw_get_rate(__le32 rate_n_flags)
+/*
+ * RAxTID to queue translation mapping.
+ *
+ * When queue is in Scheduler-ACK mode, frames placed in a that queue must be
+ * for only one combination of receiver address (RA) and traffic ID (TID), i.e.
+ * one QOS priority level destined for one station (for this wireless link,
+ * not final destination). The SCD_TRANSLATE_TABLE area provides 16 16-bit
+ * mappings, one for each of the 16 queues. If queue is not in Scheduler-ACK
+ * mode, the device ignores the mapping value.
+ *
+ * Bit fields, for each 16-bit map:
+ * 15-9: Reserved, set to 0
+ * 8-4: Index into device's station table for recipient station
+ * 3-0: Traffic ID (tid), range 0-15
+ *
+ * Driver should clear this entire area (size 32 bytes) to 0 after receiving
+ * "Alive" notification from uCode. To update a 16-bit map value, driver
+ * must read a dword-aligned value from device SRAM, replace the 16-bit map
+ * value of interest, and write the dword value back into device SRAM.
+ */
+#define SCD_TRANSLATE_TBL_OFFSET 0x500
+
+/* Find translation table dword to read/write for given queue */
+#define SCD_TRANSLATE_TBL_OFFSET_QUEUE(x) \
+ ((SCD_TRANSLATE_TBL_OFFSET + ((x) * 2)) & 0xfffffffc)
+
+#define SCD_TXFIFO_POS_TID (0)
+#define SCD_TXFIFO_POS_RA (4)
+#define SCD_QUEUE_RA_TID_MAP_RATID_MSK (0x01FF)
+
+/*********************** END TX SCHEDULER *************************************/
+
+static inline u8 iwl4965_hw_get_rate(__le32 rate_n_flags)
{
return le32_to_cpu(rate_n_flags) & 0xFF;
}
-static inline u16 iwl_hw_get_rate_n_flags(__le32 rate_n_flags)
+static inline u16 iwl4965_hw_get_rate_n_flags(__le32 rate_n_flags)
{
return le32_to_cpu(rate_n_flags) & 0xFFFF;
}
-static inline __le32 iwl_hw_set_rate_n_flags(u8 rate, u16 flags)
+static inline __le32 iwl4965_hw_set_rate_n_flags(u8 rate, u16 flags)
{
return cpu_to_le32(flags|(u16)rate);
}
-struct iwl_tfd_frame_data {
+
+/**
+ * Tx/Rx Queues
+ *
+ * Most communication between driver and 4965 is via queues of data buffers.
+ * For example, all commands that the driver issues to device's embedded
+ * controller (uCode) are via the command queue (one of the Tx queues). All
+ * uCode command responses/replies/notifications, including Rx frames, are
+ * conveyed from uCode to driver via the Rx queue.
+ *
+ * Most support for these queues, including handshake support, resides in
+ * structures in host DRAM, shared between the driver and the device. When
+ * allocating this memory, the driver must make sure that data written by
+ * the host CPU updates DRAM immediately (and does not get "stuck" in CPU's
+ * cache memory), so DRAM and cache are consistent, and the device can
+ * immediately see changes made by the driver.
+ *
+ * 4965 supports up to 16 DRAM-based Tx queues, and services these queues via
+ * up to 7 DMA channels (FIFOs). Each Tx queue is supported by a circular array
+ * in DRAM containing 256 Transmit Frame Descriptors (TFDs).
+ */
+#define IWL4965_MAX_WIN_SIZE 64
+#define IWL4965_QUEUE_SIZE 256
+#define IWL4965_NUM_FIFOS 7
+#define IWL_MAX_NUM_QUEUES 16
+
+
+/**
+ * struct iwl4965_tfd_frame_data
+ *
+ * Describes up to 2 buffers containing (contiguous) portions of a Tx frame.
+ * Each buffer must be on dword boundary.
+ * Up to 10 iwl_tfd_frame_data structures, describing up to 20 buffers,
+ * may be filled within a TFD (iwl_tfd_frame).
+ *
+ * Bit fields in tb1_addr:
+ * 31- 0: Tx buffer 1 address bits [31:0]
+ *
+ * Bit fields in val1:
+ * 31-16: Tx buffer 2 address bits [15:0]
+ * 15- 4: Tx buffer 1 length (bytes)
+ * 3- 0: Tx buffer 1 address bits [32:32]
+ *
+ * Bit fields in val2:
+ * 31-20: Tx buffer 2 length (bytes)
+ * 19- 0: Tx buffer 2 address bits [35:16]
+ */
+struct iwl4965_tfd_frame_data {
__le32 tb1_addr;
__le32 val1;
@@ -509,7 +1926,36 @@ struct iwl_tfd_frame_data {
#define IWL_tb2_len_SYM val2
} __attribute__ ((packed));
-struct iwl_tfd_frame {
+
+/**
+ * struct iwl4965_tfd_frame
+ *
+ * Transmit Frame Descriptor (TFD)
+ *
+ * 4965 supports up to 16 Tx queues resident in host DRAM.
+ * Each Tx queue uses a circular buffer of 256 TFDs stored in host DRAM.
+ * Both driver and device share these circular buffers, each of which must be
+ * contiguous 256 TFDs x 128 bytes-per-TFD = 32 KBytes for 4965.
+ *
+ * Driver must indicate the physical address of the base of each
+ * circular buffer via the 4965's FH_MEM_CBBC_QUEUE registers.
+ *
+ * Each TFD contains pointer/size information for up to 20 data buffers
+ * in host DRAM. These buffers collectively contain the (one) frame described
+ * by the TFD. Each buffer must be a single contiguous block of memory within
+ * itself, but buffers may be scattered in host DRAM. Each buffer has max size
+ * of (4K - 4). The 4965 concatenates all of a TFD's buffers into a single
+ * Tx frame, up to 8 KBytes in size.
+ *
+ * Bit fields in the control dword (val0):
+ * 31-30: # dwords (0-3) of padding required at end of frame for 16-byte bound
+ * 29: reserved
+ * 28-24: # Transmit Buffer Descriptors in TFD
+ * 23- 0: reserved
+ *
+ * A maximum of 255 (not 256!) TFDs may be on a queue waiting for Tx.
+ */
+struct iwl4965_tfd_frame {
__le32 val0;
/* __le32 rsvd1:24; */
/* __le32 num_tbs:5; */
@@ -518,15 +1964,20 @@ struct iwl_tfd_frame {
#define IWL_num_tbs_SYM val0
/* __le32 rsvd2:1; */
/* __le32 padding:2; */
- struct iwl_tfd_frame_data pa[10];
+ struct iwl4965_tfd_frame_data pa[10];
__le32 reserved;
} __attribute__ ((packed));
-#define IWL4965_MAX_WIN_SIZE 64
-#define IWL4965_QUEUE_SIZE 256
-#define IWL4965_NUM_FIFOS 7
-#define IWL_MAX_NUM_QUEUES 16
+/**
+ * struct iwl4965_queue_byte_cnt_entry
+ *
+ * Byte Count Table Entry
+ *
+ * Bit fields:
+ * 15-12: reserved
+ * 11- 0: total to-be-transmitted byte count of frame (does not include command)
+ */
struct iwl4965_queue_byte_cnt_entry {
__le16 val;
/* __le16 byte_cnt:12; */
@@ -536,6 +1987,25 @@ struct iwl4965_queue_byte_cnt_entry {
/* __le16 rsvd:4; */
} __attribute__ ((packed));
+
+/**
+ * struct iwl4965_sched_queue_byte_cnt_tbl
+ *
+ * Byte Count table
+ *
+ * Each Tx queue uses a byte-count table containing 320 entries:
+ * one 16-bit entry for each of 256 TFDs, plus an additional 64 entries that
+ * duplicate the first 64 entries (to avoid wrap-around within a Tx window;
+ * max Tx window is 64 TFDs).
+ *
+ * When driver sets up a new TFD, it must also enter the total byte count
+ * of the frame to be transmitted into the corresponding entry in the byte
+ * count table for the chosen Tx queue. If the TFD index is 0-63, the driver
+ * must duplicate the byte count entry in corresponding index 256-319.
+ *
+ * "dont_care" padding puts each byte count table on a 1024-byte boundary;
+ * 4965 assumes tables are separated by 1024 bytes.
+ */
struct iwl4965_sched_queue_byte_cnt_tbl {
struct iwl4965_queue_byte_cnt_entry tfd_offset[IWL4965_QUEUE_SIZE +
IWL4965_MAX_WIN_SIZE];
@@ -544,9 +2014,31 @@ struct iwl4965_sched_queue_byte_cnt_tbl {
sizeof(__le16)];
} __attribute__ ((packed));
-/* Base physical address of iwl_shared is provided to SCD_DRAM_BASE_ADDR
- * and &iwl_shared.val0 is provided to FH_RSCSR_CHNL0_STTS_WPTR_REG */
-struct iwl_shared {
+
+/**
+ * struct iwl4965_shared - handshake area for Tx and Rx
+ *
+ * For convenience in allocating memory, this structure combines 2 areas of
+ * DRAM which must be shared between driver and 4965. These do not need to
+ * be combined, if better allocation would result from keeping them separate:
+ *
+ * 1) The Tx byte count tables occupy 1024 bytes each (16 KBytes total for
+ * 16 queues). Driver uses SCD_DRAM_BASE_ADDR to tell 4965 where to find
+ * the first of these tables. 4965 assumes tables are 1024 bytes apart.
+ *
+ * 2) The Rx status (val0 and val1) occupies only 8 bytes. Driver uses
+ * FH_RSCSR_CHNL0_STTS_WPTR_REG to tell 4965 where to find this area.
+ * Driver reads val0 to determine the latest Receive Buffer Descriptor (RBD)
+ * that has been filled by the 4965.
+ *
+ * Bit fields val0:
+ * 31-12: Not used
+ * 11- 0: Index of last filled Rx buffer descriptor (4965 writes, driver reads)
+ *
+ * Bit fields val1:
+ * 31- 0: Not used
+ */
+struct iwl4965_shared {
struct iwl4965_sched_queue_byte_cnt_tbl
queues_byte_cnt_tbls[IWL_MAX_NUM_QUEUES];
__le32 val0;
@@ -578,4 +2070,4 @@ struct iwl_shared {
__le32 padding2;
} __attribute__ ((packed));
-#endif /* __iwl_4965_hw_h__ */
+#endif /* __iwl4965_4965_hw_h__ */