summaryrefslogtreecommitdiff
path: root/drivers/net
diff options
context:
space:
mode:
Diffstat (limited to 'drivers/net')
-rw-r--r--drivers/net/e100.c26
-rw-r--r--drivers/net/e1000e/defines.h2
-rw-r--r--drivers/net/e1000e/e1000.h14
-rw-r--r--drivers/net/e1000e/hw.h1
-rw-r--r--drivers/net/e1000e/ich8lan.c482
-rw-r--r--drivers/net/e1000e/phy.c15
-rw-r--r--drivers/net/pcmcia/pcnet_cs.c2
-rw-r--r--drivers/net/r8169.c2
-rw-r--r--drivers/net/sky2.c2
-rw-r--r--drivers/net/tokenring/ibmtr.c11
-rw-r--r--drivers/net/wireless/ath/ath9k/rc.c2
-rw-r--r--drivers/net/wireless/b43/dma.c15
-rw-r--r--drivers/net/wireless/ipw2x00/ipw2100.c5
-rw-r--r--drivers/net/wireless/ipw2x00/ipw2200.c2
-rw-r--r--drivers/net/wireless/ipw2x00/libipw.h1
-rw-r--r--drivers/net/wireless/ipw2x00/libipw_module.c14
-rw-r--r--drivers/net/wireless/libertas/if_usb.c2
-rw-r--r--drivers/net/wireless/rt2x00/rt73usb.c5
18 files changed, 476 insertions, 127 deletions
diff --git a/drivers/net/e100.c b/drivers/net/e100.c
index 5d2f48f02251..3c29a20b751e 100644
--- a/drivers/net/e100.c
+++ b/drivers/net/e100.c
@@ -1427,19 +1427,31 @@ static int e100_phy_init(struct nic *nic)
} else
DPRINTK(HW, DEBUG, "phy_addr = %d\n", nic->mii.phy_id);
- /* Isolate all the PHY ids */
- for (addr = 0; addr < 32; addr++)
- mdio_write(netdev, addr, MII_BMCR, BMCR_ISOLATE);
- /* Select the discovered PHY */
- bmcr &= ~BMCR_ISOLATE;
- mdio_write(netdev, nic->mii.phy_id, MII_BMCR, bmcr);
-
/* Get phy ID */
id_lo = mdio_read(netdev, nic->mii.phy_id, MII_PHYSID1);
id_hi = mdio_read(netdev, nic->mii.phy_id, MII_PHYSID2);
nic->phy = (u32)id_hi << 16 | (u32)id_lo;
DPRINTK(HW, DEBUG, "phy ID = 0x%08X\n", nic->phy);
+ /* Select the phy and isolate the rest */
+ for (addr = 0; addr < 32; addr++) {
+ if (addr != nic->mii.phy_id) {
+ mdio_write(netdev, addr, MII_BMCR, BMCR_ISOLATE);
+ } else if (nic->phy != phy_82552_v) {
+ bmcr = mdio_read(netdev, addr, MII_BMCR);
+ mdio_write(netdev, addr, MII_BMCR,
+ bmcr & ~BMCR_ISOLATE);
+ }
+ }
+ /*
+ * Workaround for 82552:
+ * Clear the ISOLATE bit on selected phy_id last (mirrored on all
+ * other phy_id's) using bmcr value from addr discovery loop above.
+ */
+ if (nic->phy == phy_82552_v)
+ mdio_write(netdev, nic->mii.phy_id, MII_BMCR,
+ bmcr & ~BMCR_ISOLATE);
+
/* Handle National tx phys */
#define NCS_PHY_MODEL_MASK 0xFFF0FFFF
if ((nic->phy & NCS_PHY_MODEL_MASK) == phy_nsc_tx) {
diff --git a/drivers/net/e1000e/defines.h b/drivers/net/e1000e/defines.h
index c0f185beb8bc..1190167a8b3d 100644
--- a/drivers/net/e1000e/defines.h
+++ b/drivers/net/e1000e/defines.h
@@ -76,6 +76,7 @@
/* Extended Device Control */
#define E1000_CTRL_EXT_SDP7_DATA 0x00000080 /* Value of SW Definable Pin 7 */
#define E1000_CTRL_EXT_EE_RST 0x00002000 /* Reinitialize from EEPROM */
+#define E1000_CTRL_EXT_SPD_BYPS 0x00008000 /* Speed Select Bypass */
#define E1000_CTRL_EXT_RO_DIS 0x00020000 /* Relaxed Ordering disable */
#define E1000_CTRL_EXT_DMA_DYN_CLK_EN 0x00080000 /* DMA Dynamic Clock Gating */
#define E1000_CTRL_EXT_LINK_MODE_MASK 0x00C00000
@@ -347,6 +348,7 @@
/* Extended Configuration Control and Size */
#define E1000_EXTCNF_CTRL_MDIO_SW_OWNERSHIP 0x00000020
#define E1000_EXTCNF_CTRL_LCD_WRITE_ENABLE 0x00000001
+#define E1000_EXTCNF_CTRL_OEM_WRITE_ENABLE 0x00000008
#define E1000_EXTCNF_CTRL_SWFLAG 0x00000020
#define E1000_EXTCNF_SIZE_EXT_PCIE_LENGTH_MASK 0x00FF0000
#define E1000_EXTCNF_SIZE_EXT_PCIE_LENGTH_SHIFT 16
diff --git a/drivers/net/e1000e/e1000.h b/drivers/net/e1000e/e1000.h
index 405a144ebcad..189dfa2d6c76 100644
--- a/drivers/net/e1000e/e1000.h
+++ b/drivers/net/e1000e/e1000.h
@@ -141,6 +141,20 @@ struct e1000_info;
#define HV_TNCRS_UPPER PHY_REG(778, 29) /* Transmit with no CRS */
#define HV_TNCRS_LOWER PHY_REG(778, 30)
+/* BM PHY Copper Specific Status */
+#define BM_CS_STATUS 17
+#define BM_CS_STATUS_LINK_UP 0x0400
+#define BM_CS_STATUS_RESOLVED 0x0800
+#define BM_CS_STATUS_SPEED_MASK 0xC000
+#define BM_CS_STATUS_SPEED_1000 0x8000
+
+/* 82577 Mobile Phy Status Register */
+#define HV_M_STATUS 26
+#define HV_M_STATUS_AUTONEG_COMPLETE 0x1000
+#define HV_M_STATUS_SPEED_MASK 0x0300
+#define HV_M_STATUS_SPEED_1000 0x0200
+#define HV_M_STATUS_LINK_UP 0x0040
+
enum e1000_boards {
board_82571,
board_82572,
diff --git a/drivers/net/e1000e/hw.h b/drivers/net/e1000e/hw.h
index 7b05cf47f7f5..aaea41ef794d 100644
--- a/drivers/net/e1000e/hw.h
+++ b/drivers/net/e1000e/hw.h
@@ -903,6 +903,7 @@ struct e1000_shadow_ram {
struct e1000_dev_spec_ich8lan {
bool kmrn_lock_loss_workaround_enabled;
struct e1000_shadow_ram shadow_ram[E1000_ICH8_SHADOW_RAM_WORDS];
+ bool nvm_k1_enabled;
};
struct e1000_hw {
diff --git a/drivers/net/e1000e/ich8lan.c b/drivers/net/e1000e/ich8lan.c
index b6388b9535fd..51ddb04ab195 100644
--- a/drivers/net/e1000e/ich8lan.c
+++ b/drivers/net/e1000e/ich8lan.c
@@ -124,11 +124,25 @@
#define SW_FLAG_TIMEOUT 1000 /* SW Semaphore flag timeout in milliseconds */
+/* SMBus Address Phy Register */
+#define HV_SMB_ADDR PHY_REG(768, 26)
+#define HV_SMB_ADDR_PEC_EN 0x0200
+#define HV_SMB_ADDR_VALID 0x0080
+
+/* Strapping Option Register - RO */
+#define E1000_STRAP 0x0000C
+#define E1000_STRAP_SMBUS_ADDRESS_MASK 0x00FE0000
+#define E1000_STRAP_SMBUS_ADDRESS_SHIFT 17
+
/* OEM Bits Phy Register */
#define HV_OEM_BITS PHY_REG(768, 25)
#define HV_OEM_BITS_LPLU 0x0004 /* Low Power Link Up */
+#define HV_OEM_BITS_GBE_DIS 0x0040 /* Gigabit Disable */
#define HV_OEM_BITS_RESTART_AN 0x0400 /* Restart Auto-negotiation */
+#define E1000_NVM_K1_CONFIG 0x1B /* NVM K1 Config Word */
+#define E1000_NVM_K1_ENABLE 0x1 /* NVM Enable K1 bit */
+
/* ICH GbE Flash Hardware Sequencing Flash Status Register bit breakdown */
/* Offset 04h HSFSTS */
union ich8_hws_flash_status {
@@ -208,6 +222,9 @@ static s32 e1000_cleanup_led_pchlan(struct e1000_hw *hw);
static s32 e1000_led_on_pchlan(struct e1000_hw *hw);
static s32 e1000_led_off_pchlan(struct e1000_hw *hw);
static s32 e1000_set_lplu_state_pchlan(struct e1000_hw *hw, bool active);
+static void e1000_lan_init_done_ich8lan(struct e1000_hw *hw);
+static s32 e1000_k1_gig_workaround_hv(struct e1000_hw *hw, bool link);
+static s32 e1000_configure_k1_ich8lan(struct e1000_hw *hw, bool k1_enable);
static inline u16 __er16flash(struct e1000_hw *hw, unsigned long reg)
{
@@ -483,14 +500,6 @@ static s32 e1000_check_for_copper_link_ich8lan(struct e1000_hw *hw)
goto out;
}
- if (hw->mac.type == e1000_pchlan) {
- ret_val = e1000e_write_kmrn_reg(hw,
- E1000_KMRNCTRLSTA_K1_CONFIG,
- E1000_KMRNCTRLSTA_K1_ENABLE);
- if (ret_val)
- goto out;
- }
-
/*
* First we want to see if the MII Status Register reports
* link. If so, then we want to get the current speed/duplex
@@ -500,6 +509,12 @@ static s32 e1000_check_for_copper_link_ich8lan(struct e1000_hw *hw)
if (ret_val)
goto out;
+ if (hw->mac.type == e1000_pchlan) {
+ ret_val = e1000_k1_gig_workaround_hv(hw, link);
+ if (ret_val)
+ goto out;
+ }
+
if (!link)
goto out; /* No link detected */
@@ -794,6 +809,326 @@ static s32 e1000_phy_force_speed_duplex_ich8lan(struct e1000_hw *hw)
}
/**
+ * e1000_sw_lcd_config_ich8lan - SW-based LCD Configuration
+ * @hw: pointer to the HW structure
+ *
+ * SW should configure the LCD from the NVM extended configuration region
+ * as a workaround for certain parts.
+ **/
+static s32 e1000_sw_lcd_config_ich8lan(struct e1000_hw *hw)
+{
+ struct e1000_phy_info *phy = &hw->phy;
+ u32 i, data, cnf_size, cnf_base_addr, sw_cfg_mask;
+ s32 ret_val;
+ u16 word_addr, reg_data, reg_addr, phy_page = 0;
+
+ ret_val = hw->phy.ops.acquire_phy(hw);
+ if (ret_val)
+ return ret_val;
+
+ /*
+ * Initialize the PHY from the NVM on ICH platforms. This
+ * is needed due to an issue where the NVM configuration is
+ * not properly autoloaded after power transitions.
+ * Therefore, after each PHY reset, we will load the
+ * configuration data out of the NVM manually.
+ */
+ if ((hw->mac.type == e1000_ich8lan && phy->type == e1000_phy_igp_3) ||
+ (hw->mac.type == e1000_pchlan)) {
+ struct e1000_adapter *adapter = hw->adapter;
+
+ /* Check if SW needs to configure the PHY */
+ if ((adapter->pdev->device == E1000_DEV_ID_ICH8_IGP_M_AMT) ||
+ (adapter->pdev->device == E1000_DEV_ID_ICH8_IGP_M) ||
+ (hw->mac.type == e1000_pchlan))
+ sw_cfg_mask = E1000_FEXTNVM_SW_CONFIG_ICH8M;
+ else
+ sw_cfg_mask = E1000_FEXTNVM_SW_CONFIG;
+
+ data = er32(FEXTNVM);
+ if (!(data & sw_cfg_mask))
+ goto out;
+
+ /* Wait for basic configuration completes before proceeding */
+ e1000_lan_init_done_ich8lan(hw);
+
+ /*
+ * Make sure HW does not configure LCD from PHY
+ * extended configuration before SW configuration
+ */
+ data = er32(EXTCNF_CTRL);
+ if (data & E1000_EXTCNF_CTRL_LCD_WRITE_ENABLE)
+ goto out;
+
+ cnf_size = er32(EXTCNF_SIZE);
+ cnf_size &= E1000_EXTCNF_SIZE_EXT_PCIE_LENGTH_MASK;
+ cnf_size >>= E1000_EXTCNF_SIZE_EXT_PCIE_LENGTH_SHIFT;
+ if (!cnf_size)
+ goto out;
+
+ cnf_base_addr = data & E1000_EXTCNF_CTRL_EXT_CNF_POINTER_MASK;
+ cnf_base_addr >>= E1000_EXTCNF_CTRL_EXT_CNF_POINTER_SHIFT;
+
+ if (!(data & E1000_EXTCNF_CTRL_OEM_WRITE_ENABLE) &&
+ (hw->mac.type == e1000_pchlan)) {
+ /*
+ * HW configures the SMBus address and LEDs when the
+ * OEM and LCD Write Enable bits are set in the NVM.
+ * When both NVM bits are cleared, SW will configure
+ * them instead.
+ */
+ data = er32(STRAP);
+ data &= E1000_STRAP_SMBUS_ADDRESS_MASK;
+ reg_data = data >> E1000_STRAP_SMBUS_ADDRESS_SHIFT;
+ reg_data |= HV_SMB_ADDR_PEC_EN | HV_SMB_ADDR_VALID;
+ ret_val = e1000_write_phy_reg_hv_locked(hw, HV_SMB_ADDR,
+ reg_data);
+ if (ret_val)
+ goto out;
+
+ data = er32(LEDCTL);
+ ret_val = e1000_write_phy_reg_hv_locked(hw,
+ HV_LED_CONFIG,
+ (u16)data);
+ if (ret_val)
+ goto out;
+ }
+ /* Configure LCD from extended configuration region. */
+
+ /* cnf_base_addr is in DWORD */
+ word_addr = (u16)(cnf_base_addr << 1);
+
+ for (i = 0; i < cnf_size; i++) {
+ ret_val = e1000_read_nvm(hw, (word_addr + i * 2), 1,
+ &reg_data);
+ if (ret_val)
+ goto out;
+
+ ret_val = e1000_read_nvm(hw, (word_addr + i * 2 + 1),
+ 1, &reg_addr);
+ if (ret_val)
+ goto out;
+
+ /* Save off the PHY page for future writes. */
+ if (reg_addr == IGP01E1000_PHY_PAGE_SELECT) {
+ phy_page = reg_data;
+ continue;
+ }
+
+ reg_addr &= PHY_REG_MASK;
+ reg_addr |= phy_page;
+
+ ret_val = phy->ops.write_phy_reg_locked(hw,
+ (u32)reg_addr,
+ reg_data);
+ if (ret_val)
+ goto out;
+ }
+ }
+
+out:
+ hw->phy.ops.release_phy(hw);
+ return ret_val;
+}
+
+/**
+ * e1000_k1_gig_workaround_hv - K1 Si workaround
+ * @hw: pointer to the HW structure
+ * @link: link up bool flag
+ *
+ * If K1 is enabled for 1Gbps, the MAC might stall when transitioning
+ * from a lower speed. This workaround disables K1 whenever link is at 1Gig
+ * If link is down, the function will restore the default K1 setting located
+ * in the NVM.
+ **/
+static s32 e1000_k1_gig_workaround_hv(struct e1000_hw *hw, bool link)
+{
+ s32 ret_val = 0;
+ u16 status_reg = 0;
+ bool k1_enable = hw->dev_spec.ich8lan.nvm_k1_enabled;
+
+ if (hw->mac.type != e1000_pchlan)
+ goto out;
+
+ /* Wrap the whole flow with the sw flag */
+ ret_val = hw->phy.ops.acquire_phy(hw);
+ if (ret_val)
+ goto out;
+
+ /* Disable K1 when link is 1Gbps, otherwise use the NVM setting */
+ if (link) {
+ if (hw->phy.type == e1000_phy_82578) {
+ ret_val = hw->phy.ops.read_phy_reg_locked(hw,
+ BM_CS_STATUS,
+ &status_reg);
+ if (ret_val)
+ goto release;
+
+ status_reg &= BM_CS_STATUS_LINK_UP |
+ BM_CS_STATUS_RESOLVED |
+ BM_CS_STATUS_SPEED_MASK;
+
+ if (status_reg == (BM_CS_STATUS_LINK_UP |
+ BM_CS_STATUS_RESOLVED |
+ BM_CS_STATUS_SPEED_1000))
+ k1_enable = false;
+ }
+
+ if (hw->phy.type == e1000_phy_82577) {
+ ret_val = hw->phy.ops.read_phy_reg_locked(hw,
+ HV_M_STATUS,
+ &status_reg);
+ if (ret_val)
+ goto release;
+
+ status_reg &= HV_M_STATUS_LINK_UP |
+ HV_M_STATUS_AUTONEG_COMPLETE |
+ HV_M_STATUS_SPEED_MASK;
+
+ if (status_reg == (HV_M_STATUS_LINK_UP |
+ HV_M_STATUS_AUTONEG_COMPLETE |
+ HV_M_STATUS_SPEED_1000))
+ k1_enable = false;
+ }
+
+ /* Link stall fix for link up */
+ ret_val = hw->phy.ops.write_phy_reg_locked(hw, PHY_REG(770, 19),
+ 0x0100);
+ if (ret_val)
+ goto release;
+
+ } else {
+ /* Link stall fix for link down */
+ ret_val = hw->phy.ops.write_phy_reg_locked(hw, PHY_REG(770, 19),
+ 0x4100);
+ if (ret_val)
+ goto release;
+ }
+
+ ret_val = e1000_configure_k1_ich8lan(hw, k1_enable);
+
+release:
+ hw->phy.ops.release_phy(hw);
+out:
+ return ret_val;
+}
+
+/**
+ * e1000_configure_k1_ich8lan - Configure K1 power state
+ * @hw: pointer to the HW structure
+ * @enable: K1 state to configure
+ *
+ * Configure the K1 power state based on the provided parameter.
+ * Assumes semaphore already acquired.
+ *
+ * Success returns 0, Failure returns -E1000_ERR_PHY (-2)
+ **/
+static s32 e1000_configure_k1_ich8lan(struct e1000_hw *hw, bool k1_enable)
+{
+ s32 ret_val = 0;
+ u32 ctrl_reg = 0;
+ u32 ctrl_ext = 0;
+ u32 reg = 0;
+ u16 kmrn_reg = 0;
+
+ ret_val = e1000e_read_kmrn_reg_locked(hw,
+ E1000_KMRNCTRLSTA_K1_CONFIG,
+ &kmrn_reg);
+ if (ret_val)
+ goto out;
+
+ if (k1_enable)
+ kmrn_reg |= E1000_KMRNCTRLSTA_K1_ENABLE;
+ else
+ kmrn_reg &= ~E1000_KMRNCTRLSTA_K1_ENABLE;
+
+ ret_val = e1000e_write_kmrn_reg_locked(hw,
+ E1000_KMRNCTRLSTA_K1_CONFIG,
+ kmrn_reg);
+ if (ret_val)
+ goto out;
+
+ udelay(20);
+ ctrl_ext = er32(CTRL_EXT);
+ ctrl_reg = er32(CTRL);
+
+ reg = ctrl_reg & ~(E1000_CTRL_SPD_1000 | E1000_CTRL_SPD_100);
+ reg |= E1000_CTRL_FRCSPD;
+ ew32(CTRL, reg);
+
+ ew32(CTRL_EXT, ctrl_ext | E1000_CTRL_EXT_SPD_BYPS);
+ udelay(20);
+ ew32(CTRL, ctrl_reg);
+ ew32(CTRL_EXT, ctrl_ext);
+ udelay(20);
+
+out:
+ return ret_val;
+}
+
+/**
+ * e1000_oem_bits_config_ich8lan - SW-based LCD Configuration
+ * @hw: pointer to the HW structure
+ * @d0_state: boolean if entering d0 or d3 device state
+ *
+ * SW will configure Gbe Disable and LPLU based on the NVM. The four bits are
+ * collectively called OEM bits. The OEM Write Enable bit and SW Config bit
+ * in NVM determines whether HW should configure LPLU and Gbe Disable.
+ **/
+static s32 e1000_oem_bits_config_ich8lan(struct e1000_hw *hw, bool d0_state)
+{
+ s32 ret_val = 0;
+ u32 mac_reg;
+ u16 oem_reg;
+
+ if (hw->mac.type != e1000_pchlan)
+ return ret_val;
+
+ ret_val = hw->phy.ops.acquire_phy(hw);
+ if (ret_val)
+ return ret_val;
+
+ mac_reg = er32(EXTCNF_CTRL);
+ if (mac_reg & E1000_EXTCNF_CTRL_OEM_WRITE_ENABLE)
+ goto out;
+
+ mac_reg = er32(FEXTNVM);
+ if (!(mac_reg & E1000_FEXTNVM_SW_CONFIG_ICH8M))
+ goto out;
+
+ mac_reg = er32(PHY_CTRL);
+
+ ret_val = hw->phy.ops.read_phy_reg_locked(hw, HV_OEM_BITS, &oem_reg);
+ if (ret_val)
+ goto out;
+
+ oem_reg &= ~(HV_OEM_BITS_GBE_DIS | HV_OEM_BITS_LPLU);
+
+ if (d0_state) {
+ if (mac_reg & E1000_PHY_CTRL_GBE_DISABLE)
+ oem_reg |= HV_OEM_BITS_GBE_DIS;
+
+ if (mac_reg & E1000_PHY_CTRL_D0A_LPLU)
+ oem_reg |= HV_OEM_BITS_LPLU;
+ } else {
+ if (mac_reg & E1000_PHY_CTRL_NOND0A_GBE_DISABLE)
+ oem_reg |= HV_OEM_BITS_GBE_DIS;
+
+ if (mac_reg & E1000_PHY_CTRL_NOND0A_LPLU)
+ oem_reg |= HV_OEM_BITS_LPLU;
+ }
+ /* Restart auto-neg to activate the bits */
+ oem_reg |= HV_OEM_BITS_RESTART_AN;
+ ret_val = hw->phy.ops.write_phy_reg_locked(hw, HV_OEM_BITS, oem_reg);
+
+out:
+ hw->phy.ops.release_phy(hw);
+
+ return ret_val;
+}
+
+
+/**
* e1000_hv_phy_workarounds_ich8lan - A series of Phy workarounds to be
* done after every PHY reset.
**/
@@ -833,10 +1168,20 @@ static s32 e1000_hv_phy_workarounds_ich8lan(struct e1000_hw *hw)
ret_val = hw->phy.ops.acquire_phy(hw);
if (ret_val)
return ret_val;
+
hw->phy.addr = 1;
- e1000e_write_phy_reg_mdic(hw, IGP01E1000_PHY_PAGE_SELECT, 0);
+ ret_val = e1000e_write_phy_reg_mdic(hw, IGP01E1000_PHY_PAGE_SELECT, 0);
+ if (ret_val)
+ goto out;
hw->phy.ops.release_phy(hw);
+ /*
+ * Configure the K1 Si workaround during phy reset assuming there is
+ * link so that it disables K1 if link is in 1Gbps.
+ */
+ ret_val = e1000_k1_gig_workaround_hv(hw, true);
+
+out:
return ret_val;
}
@@ -882,11 +1227,8 @@ static void e1000_lan_init_done_ich8lan(struct e1000_hw *hw)
**/
static s32 e1000_phy_hw_reset_ich8lan(struct e1000_hw *hw)
{
- struct e1000_phy_info *phy = &hw->phy;
- u32 i;
- u32 data, cnf_size, cnf_base_addr, sw_cfg_mask;
- s32 ret_val;
- u16 reg, word_addr, reg_data, reg_addr, phy_page = 0;
+ s32 ret_val = 0;
+ u16 reg;
ret_val = e1000e_phy_hw_reset_generic(hw);
if (ret_val)
@@ -905,81 +1247,16 @@ static s32 e1000_phy_hw_reset_ich8lan(struct e1000_hw *hw)
if (hw->mac.type == e1000_pchlan)
e1e_rphy(hw, BM_WUC, &reg);
- /*
- * Initialize the PHY from the NVM on ICH platforms. This
- * is needed due to an issue where the NVM configuration is
- * not properly autoloaded after power transitions.
- * Therefore, after each PHY reset, we will load the
- * configuration data out of the NVM manually.
- */
- if (hw->mac.type == e1000_ich8lan && phy->type == e1000_phy_igp_3) {
- struct e1000_adapter *adapter = hw->adapter;
-
- /* Check if SW needs configure the PHY */
- if ((adapter->pdev->device == E1000_DEV_ID_ICH8_IGP_M_AMT) ||
- (adapter->pdev->device == E1000_DEV_ID_ICH8_IGP_M))
- sw_cfg_mask = E1000_FEXTNVM_SW_CONFIG_ICH8M;
- else
- sw_cfg_mask = E1000_FEXTNVM_SW_CONFIG;
-
- data = er32(FEXTNVM);
- if (!(data & sw_cfg_mask))
- return 0;
-
- /* Wait for basic configuration completes before proceeding */
- e1000_lan_init_done_ich8lan(hw);
-
- /*
- * Make sure HW does not configure LCD from PHY
- * extended configuration before SW configuration
- */
- data = er32(EXTCNF_CTRL);
- if (data & E1000_EXTCNF_CTRL_LCD_WRITE_ENABLE)
- return 0;
-
- cnf_size = er32(EXTCNF_SIZE);
- cnf_size &= E1000_EXTCNF_SIZE_EXT_PCIE_LENGTH_MASK;
- cnf_size >>= E1000_EXTCNF_SIZE_EXT_PCIE_LENGTH_SHIFT;
- if (!cnf_size)
- return 0;
-
- cnf_base_addr = data & E1000_EXTCNF_CTRL_EXT_CNF_POINTER_MASK;
- cnf_base_addr >>= E1000_EXTCNF_CTRL_EXT_CNF_POINTER_SHIFT;
-
- /* Configure LCD from extended configuration region. */
-
- /* cnf_base_addr is in DWORD */
- word_addr = (u16)(cnf_base_addr << 1);
-
- for (i = 0; i < cnf_size; i++) {
- ret_val = e1000_read_nvm(hw,
- (word_addr + i * 2),
- 1,
- &reg_data);
- if (ret_val)
- return ret_val;
-
- ret_val = e1000_read_nvm(hw,
- (word_addr + i * 2 + 1),
- 1,
- &reg_addr);
- if (ret_val)
- return ret_val;
-
- /* Save off the PHY page for future writes. */
- if (reg_addr == IGP01E1000_PHY_PAGE_SELECT) {
- phy_page = reg_data;
- continue;
- }
-
- reg_addr |= phy_page;
+ /* Configure the LCD with the extended configuration region in NVM */
+ ret_val = e1000_sw_lcd_config_ich8lan(hw);
+ if (ret_val)
+ goto out;
- ret_val = e1e_wphy(hw, (u32)reg_addr, reg_data);
- if (ret_val)
- return ret_val;
- }
- }
+ /* Configure the LCD with the OEM bits in NVM */
+ if (hw->mac.type == e1000_pchlan)
+ ret_val = e1000_oem_bits_config_ich8lan(hw, true);
+out:
return 0;
}
@@ -2306,6 +2583,7 @@ static s32 e1000_get_bus_info_ich8lan(struct e1000_hw *hw)
**/
static s32 e1000_reset_hw_ich8lan(struct e1000_hw *hw)
{
+ struct e1000_dev_spec_ich8lan *dev_spec = &hw->dev_spec.ich8lan;
u16 reg;
u32 ctrl, icr, kab;
s32 ret_val;
@@ -2341,6 +2619,18 @@ static s32 e1000_reset_hw_ich8lan(struct e1000_hw *hw)
ew32(PBS, E1000_PBS_16K);
}
+ if (hw->mac.type == e1000_pchlan) {
+ /* Save the NVM K1 bit setting*/
+ ret_val = e1000_read_nvm(hw, E1000_NVM_K1_CONFIG, 1, &reg);
+ if (ret_val)
+ return ret_val;
+
+ if (reg & E1000_NVM_K1_ENABLE)
+ dev_spec->nvm_k1_enabled = true;
+ else
+ dev_spec->nvm_k1_enabled = false;
+ }
+
ctrl = er32(CTRL);
if (!e1000_check_reset_block(hw)) {
@@ -2386,6 +2676,15 @@ static s32 e1000_reset_hw_ich8lan(struct e1000_hw *hw)
if (hw->mac.type == e1000_pchlan)
e1e_rphy(hw, BM_WUC, &reg);
+ ret_val = e1000_sw_lcd_config_ich8lan(hw);
+ if (ret_val)
+ goto out;
+
+ if (hw->mac.type == e1000_pchlan) {
+ ret_val = e1000_oem_bits_config_ich8lan(hw, true);
+ if (ret_val)
+ goto out;
+ }
/*
* For PCH, this write will make sure that any noise
* will be detected as a CRC error and be dropped rather than show up
@@ -2404,6 +2703,7 @@ static s32 e1000_reset_hw_ich8lan(struct e1000_hw *hw)
if (hw->mac.type == e1000_pchlan)
ret_val = e1000_hv_phy_workarounds_ich8lan(hw);
+out:
return ret_val;
}
@@ -2708,14 +3008,6 @@ static s32 e1000_get_link_up_info_ich8lan(struct e1000_hw *hw, u16 *speed,
if (ret_val)
return ret_val;
- if ((hw->mac.type == e1000_pchlan) && (*speed == SPEED_1000)) {
- ret_val = e1000e_write_kmrn_reg(hw,
- E1000_KMRNCTRLSTA_K1_CONFIG,
- E1000_KMRNCTRLSTA_K1_DISABLE);
- if (ret_val)
- return ret_val;
- }
-
if ((hw->mac.type == e1000_ich8lan) &&
(hw->phy.type == e1000_phy_igp_3) &&
(*speed == SPEED_1000)) {
diff --git a/drivers/net/e1000e/phy.c b/drivers/net/e1000e/phy.c
index f9d33ab05e97..03175b3a2c9e 100644
--- a/drivers/net/e1000e/phy.c
+++ b/drivers/net/e1000e/phy.c
@@ -95,13 +95,6 @@ static const u16 e1000_igp_2_cable_length_table[] =
/* BM PHY Copper Specific Control 1 */
#define BM_CS_CTRL1 16
-/* BM PHY Copper Specific Status */
-#define BM_CS_STATUS 17
-#define BM_CS_STATUS_LINK_UP 0x0400
-#define BM_CS_STATUS_RESOLVED 0x0800
-#define BM_CS_STATUS_SPEED_MASK 0xC000
-#define BM_CS_STATUS_SPEED_1000 0x8000
-
#define HV_MUX_DATA_CTRL PHY_REG(776, 16)
#define HV_MUX_DATA_CTRL_GEN_TO_MAC 0x0400
#define HV_MUX_DATA_CTRL_FORCE_SPEED 0x0004
@@ -563,7 +556,7 @@ s32 e1000e_read_kmrn_reg(struct e1000_hw *hw, u32 offset, u16 *data)
}
/**
- * e1000_read_kmrn_reg_locked - Read kumeran register
+ * e1000e_read_kmrn_reg_locked - Read kumeran register
* @hw: pointer to the HW structure
* @offset: register offset to be read
* @data: pointer to the read data
@@ -572,7 +565,7 @@ s32 e1000e_read_kmrn_reg(struct e1000_hw *hw, u32 offset, u16 *data)
* information retrieved is stored in data.
* Assumes semaphore already acquired.
**/
-s32 e1000_read_kmrn_reg_locked(struct e1000_hw *hw, u32 offset, u16 *data)
+s32 e1000e_read_kmrn_reg_locked(struct e1000_hw *hw, u32 offset, u16 *data)
{
return __e1000_read_kmrn_reg(hw, offset, data, true);
}
@@ -631,7 +624,7 @@ s32 e1000e_write_kmrn_reg(struct e1000_hw *hw, u32 offset, u16 data)
}
/**
- * e1000_write_kmrn_reg_locked - Write kumeran register
+ * e1000e_write_kmrn_reg_locked - Write kumeran register
* @hw: pointer to the HW structure
* @offset: register offset to write to
* @data: data to write at register offset
@@ -639,7 +632,7 @@ s32 e1000e_write_kmrn_reg(struct e1000_hw *hw, u32 offset, u16 data)
* Write the data to PHY register at the offset using the kumeran interface.
* Assumes semaphore already acquired.
**/
-s32 e1000_write_kmrn_reg_locked(struct e1000_hw *hw, u32 offset, u16 data)
+s32 e1000e_write_kmrn_reg_locked(struct e1000_hw *hw, u32 offset, u16 data)
{
return __e1000_write_kmrn_reg(hw, offset, data, true);
}
diff --git a/drivers/net/pcmcia/pcnet_cs.c b/drivers/net/pcmcia/pcnet_cs.c
index bd3447f04902..94c9ad2746bc 100644
--- a/drivers/net/pcmcia/pcnet_cs.c
+++ b/drivers/net/pcmcia/pcnet_cs.c
@@ -1760,7 +1760,7 @@ static struct pcmcia_device_id pcnet_ids[] = {
PCMCIA_DEVICE_CIS_MANF_CARD(0xc00f, 0x0002, "cis/LA-PCM.cis"),
PCMCIA_DEVICE_CIS_PROD_ID12("KTI", "PE520 PLUS", 0xad180345, 0x9d58d392, "PE520.cis"),
PCMCIA_DEVICE_CIS_PROD_ID12("NDC", "Ethernet", 0x01c43ae1, 0x00b2e941, "cis/NE2K.cis"),
- PCMCIA_DEVICE_CIS_PROD_ID12("PMX ", "PE-200", 0x34f3f1c8, 0x10b59f8c, "PE-200.cis"),
+ PCMCIA_DEVICE_CIS_PROD_ID12("PMX ", "PE-200", 0x34f3f1c8, 0x10b59f8c, "cis/PE-200.cis"),
PCMCIA_DEVICE_CIS_PROD_ID12("TAMARACK", "Ethernet", 0xcf434fba, 0x00b2e941, "cis/tamarack.cis"),
PCMCIA_DEVICE_PROD_ID12("Ethernet", "CF Size PC Card", 0x00b2e941, 0x43ac239b),
PCMCIA_DEVICE_PROD_ID123("Fast Ethernet", "CF Size PC Card", "1.0",
diff --git a/drivers/net/r8169.c b/drivers/net/r8169.c
index f98ef523f525..fa4935678488 100644
--- a/drivers/net/r8169.c
+++ b/drivers/net/r8169.c
@@ -3379,7 +3379,7 @@ static u16 rtl_rw_cpluscmd(void __iomem *ioaddr)
static void rtl_set_rx_max_size(void __iomem *ioaddr, unsigned int rx_buf_sz)
{
/* Low hurts. Let's disable the filtering. */
- RTL_W16(RxMaxSize, rx_buf_sz);
+ RTL_W16(RxMaxSize, rx_buf_sz + 1);
}
static void rtl8169_set_magic_reg(void __iomem *ioaddr, unsigned mac_version)
diff --git a/drivers/net/sky2.c b/drivers/net/sky2.c
index 2ab5c39f33ca..6a10d7ba5877 100644
--- a/drivers/net/sky2.c
+++ b/drivers/net/sky2.c
@@ -4538,6 +4538,8 @@ static int __devinit sky2_probe(struct pci_dev *pdev,
goto err_out_free_netdev;
}
+ netif_carrier_off(dev);
+
netif_napi_add(dev, &hw->napi, sky2_poll, NAPI_WEIGHT);
err = request_irq(pdev->irq, sky2_intr,
diff --git a/drivers/net/tokenring/ibmtr.c b/drivers/net/tokenring/ibmtr.c
index 36cb2423bcf1..75fa32e34fd0 100644
--- a/drivers/net/tokenring/ibmtr.c
+++ b/drivers/net/tokenring/ibmtr.c
@@ -1144,9 +1144,16 @@ static void dir_open_adapter (struct net_device *dev)
} else {
char **prphase = printphase;
char **prerror = printerror;
+ int pnr = err / 16 - 1;
+ int enr = err % 16 - 1;
DPRINTK("TR Adapter misc open failure, error code = ");
- printk("0x%x, Phase: %s, Error: %s\n",
- err, prphase[err/16 -1], prerror[err%16 -1]);
+ if (pnr < 0 || pnr >= ARRAY_SIZE(printphase) ||
+ enr < 0 ||
+ enr >= ARRAY_SIZE(printerror))
+ printk("0x%x, invalid Phase/Error.", err);
+ else
+ printk("0x%x, Phase: %s, Error: %s\n", err,
+ prphase[pnr], prerror[enr]);
printk(" retrying after %ds delay...\n",
TR_RETRY_INTERVAL/HZ);
}
diff --git a/drivers/net/wireless/ath/ath9k/rc.c b/drivers/net/wireless/ath/ath9k/rc.c
index 16a271787b85..1895d63aad0a 100644
--- a/drivers/net/wireless/ath/ath9k/rc.c
+++ b/drivers/net/wireless/ath/ath9k/rc.c
@@ -679,7 +679,7 @@ static u8 ath_rc_get_highest_rix(struct ath_softc *sc,
return rate;
if (rate_table->info[rate].valid_single_stream &&
- !(ath_rc_priv->ht_cap & WLAN_RC_DS_FLAG));
+ !(ath_rc_priv->ht_cap & WLAN_RC_DS_FLAG))
return rate;
/* This should not happen */
diff --git a/drivers/net/wireless/b43/dma.c b/drivers/net/wireless/b43/dma.c
index 8701034569fa..de4e804bedf0 100644
--- a/drivers/net/wireless/b43/dma.c
+++ b/drivers/net/wireless/b43/dma.c
@@ -1157,8 +1157,9 @@ struct b43_dmaring *parse_cookie(struct b43_wldev *dev, u16 cookie, int *slot)
}
static int dma_tx_fragment(struct b43_dmaring *ring,
- struct sk_buff *skb)
+ struct sk_buff **in_skb)
{
+ struct sk_buff *skb = *in_skb;
const struct b43_dma_ops *ops = ring->ops;
struct ieee80211_tx_info *info = IEEE80211_SKB_CB(skb);
u8 *header;
@@ -1224,8 +1225,14 @@ static int dma_tx_fragment(struct b43_dmaring *ring,
}
memcpy(skb_put(bounce_skb, skb->len), skb->data, skb->len);
+ memcpy(bounce_skb->cb, skb->cb, sizeof(skb->cb));
+ bounce_skb->dev = skb->dev;
+ skb_set_queue_mapping(bounce_skb, skb_get_queue_mapping(skb));
+ info = IEEE80211_SKB_CB(bounce_skb);
+
dev_kfree_skb_any(skb);
skb = bounce_skb;
+ *in_skb = bounce_skb;
meta->skb = skb;
meta->dmaaddr = map_descbuffer(ring, skb->data, skb->len, 1);
if (b43_dma_mapping_error(ring, meta->dmaaddr, skb->len, 1)) {
@@ -1355,7 +1362,11 @@ int b43_dma_tx(struct b43_wldev *dev, struct sk_buff *skb)
* static, so we don't need to store it per frame. */
ring->queue_prio = skb_get_queue_mapping(skb);
- err = dma_tx_fragment(ring, skb);
+ /* dma_tx_fragment might reallocate the skb, so invalidate pointers pointing
+ * into the skb data or cb now. */
+ hdr = NULL;
+ info = NULL;
+ err = dma_tx_fragment(ring, &skb);
if (unlikely(err == -ENOKEY)) {
/* Drop this packet, as we don't have the encryption key
* anymore and must not transmit it unencrypted. */
diff --git a/drivers/net/wireless/ipw2x00/ipw2100.c b/drivers/net/wireless/ipw2x00/ipw2100.c
index 240cff1e6979..a741d37fd96f 100644
--- a/drivers/net/wireless/ipw2x00/ipw2100.c
+++ b/drivers/net/wireless/ipw2x00/ipw2100.c
@@ -6325,8 +6325,10 @@ static int ipw2100_pci_init_one(struct pci_dev *pci_dev,
fail:
if (dev) {
- if (registered)
+ if (registered) {
+ unregister_ieee80211(priv->ieee);
unregister_netdev(dev);
+ }
ipw2100_hw_stop_adapter(priv);
@@ -6383,6 +6385,7 @@ static void __devexit ipw2100_pci_remove_one(struct pci_dev *pci_dev)
/* Unregister the device first - this results in close()
* being called if the device is open. If we free storage
* first, then close() will crash. */
+ unregister_ieee80211(priv->ieee);
unregister_netdev(dev);
/* ipw2100_down will ensure that there is no more pending work
diff --git a/drivers/net/wireless/ipw2x00/ipw2200.c b/drivers/net/wireless/ipw2x00/ipw2200.c
index 827824d45de9..9b0f2c0646e0 100644
--- a/drivers/net/wireless/ipw2x00/ipw2200.c
+++ b/drivers/net/wireless/ipw2x00/ipw2200.c
@@ -11822,6 +11822,7 @@ static int __devinit ipw_pci_probe(struct pci_dev *pdev,
if (err) {
IPW_ERROR("Failed to register promiscuous network "
"device (error %d).\n", err);
+ unregister_ieee80211(priv->ieee);
unregister_netdev(priv->net_dev);
goto out_remove_sysfs;
}
@@ -11872,6 +11873,7 @@ static void __devexit ipw_pci_remove(struct pci_dev *pdev)
mutex_unlock(&priv->mutex);
+ unregister_ieee80211(priv->ieee);
unregister_netdev(priv->net_dev);
if (priv->rxq) {
diff --git a/drivers/net/wireless/ipw2x00/libipw.h b/drivers/net/wireless/ipw2x00/libipw.h
index bf45391172f3..f42ade6c2d3e 100644
--- a/drivers/net/wireless/ipw2x00/libipw.h
+++ b/drivers/net/wireless/ipw2x00/libipw.h
@@ -1020,6 +1020,7 @@ static inline int libipw_is_cck_rate(u8 rate)
/* ieee80211.c */
extern void free_ieee80211(struct net_device *dev, int monitor);
extern struct net_device *alloc_ieee80211(int sizeof_priv, int monitor);
+extern void unregister_ieee80211(struct libipw_device *ieee);
extern int libipw_change_mtu(struct net_device *dev, int new_mtu);
extern void libipw_networks_age(struct libipw_device *ieee,
diff --git a/drivers/net/wireless/ipw2x00/libipw_module.c b/drivers/net/wireless/ipw2x00/libipw_module.c
index a0e9f6aed7da..be5b809ec97a 100644
--- a/drivers/net/wireless/ipw2x00/libipw_module.c
+++ b/drivers/net/wireless/ipw2x00/libipw_module.c
@@ -235,16 +235,19 @@ void free_ieee80211(struct net_device *dev, int monitor)
libipw_networks_free(ieee);
/* free cfg80211 resources */
- if (!monitor) {
- wiphy_unregister(ieee->wdev.wiphy);
- kfree(ieee->a_band.channels);
- kfree(ieee->bg_band.channels);
+ if (!monitor)
wiphy_free(ieee->wdev.wiphy);
- }
free_netdev(dev);
}
+void unregister_ieee80211(struct libipw_device *ieee)
+{
+ wiphy_unregister(ieee->wdev.wiphy);
+ kfree(ieee->a_band.channels);
+ kfree(ieee->bg_band.channels);
+}
+
#ifdef CONFIG_LIBIPW_DEBUG
static int debug = 0;
@@ -330,3 +333,4 @@ module_init(libipw_init);
EXPORT_SYMBOL(alloc_ieee80211);
EXPORT_SYMBOL(free_ieee80211);
+EXPORT_SYMBOL(unregister_ieee80211);
diff --git a/drivers/net/wireless/libertas/if_usb.c b/drivers/net/wireless/libertas/if_usb.c
index 92bc8c5f1ca2..3fac4efa5ac8 100644
--- a/drivers/net/wireless/libertas/if_usb.c
+++ b/drivers/net/wireless/libertas/if_usb.c
@@ -508,7 +508,7 @@ static int __if_usb_submit_rx_urb(struct if_usb_card *cardp,
/* Fill the receive configuration URB and initialise the Rx call back */
usb_fill_bulk_urb(cardp->rx_urb, cardp->udev,
usb_rcvbulkpipe(cardp->udev, cardp->ep_in),
- (void *) (skb->tail + (size_t) IPFIELD_ALIGN_OFFSET),
+ skb->data + IPFIELD_ALIGN_OFFSET,
MRVDRV_ETH_RX_PACKET_BUFFER_SIZE, callbackfn,
cardp);
diff --git a/drivers/net/wireless/rt2x00/rt73usb.c b/drivers/net/wireless/rt2x00/rt73usb.c
index b8f5ee33445e..14e7bb210075 100644
--- a/drivers/net/wireless/rt2x00/rt73usb.c
+++ b/drivers/net/wireless/rt2x00/rt73usb.c
@@ -2389,10 +2389,13 @@ static struct usb_device_id rt73usb_device_table[] = {
{ USB_DEVICE(0x13b1, 0x0023), USB_DEVICE_DATA(&rt73usb_ops) },
{ USB_DEVICE(0x13b1, 0x0028), USB_DEVICE_DATA(&rt73usb_ops) },
/* MSI */
+ { USB_DEVICE(0x0db0, 0x4600), USB_DEVICE_DATA(&rt73usb_ops) },
{ USB_DEVICE(0x0db0, 0x6877), USB_DEVICE_DATA(&rt73usb_ops) },
{ USB_DEVICE(0x0db0, 0x6874), USB_DEVICE_DATA(&rt73usb_ops) },
{ USB_DEVICE(0x0db0, 0xa861), USB_DEVICE_DATA(&rt73usb_ops) },
{ USB_DEVICE(0x0db0, 0xa874), USB_DEVICE_DATA(&rt73usb_ops) },
+ /* Ovislink */
+ { USB_DEVICE(0x1b75, 0x7318), USB_DEVICE_DATA(&rt73usb_ops) },
/* Ralink */
{ USB_DEVICE(0x04bb, 0x093d), USB_DEVICE_DATA(&rt73usb_ops) },
{ USB_DEVICE(0x148f, 0x2573), USB_DEVICE_DATA(&rt73usb_ops) },
@@ -2420,6 +2423,8 @@ static struct usb_device_id rt73usb_device_table[] = {
/* Planex */
{ USB_DEVICE(0x2019, 0xab01), USB_DEVICE_DATA(&rt73usb_ops) },
{ USB_DEVICE(0x2019, 0xab50), USB_DEVICE_DATA(&rt73usb_ops) },
+ /* WideTell */
+ { USB_DEVICE(0x7167, 0x3840), USB_DEVICE_DATA(&rt73usb_ops) },
/* Zcom */
{ USB_DEVICE(0x0cde, 0x001c), USB_DEVICE_DATA(&rt73usb_ops) },
/* ZyXEL */
generated by cgit v1.2.3 (git 2.0.4) at 2024-11-16 01:38:05 +0000