summaryrefslogtreecommitdiff
path: root/drivers/scsi/isci/probe_roms.h
diff options
context:
space:
mode:
Diffstat (limited to 'drivers/scsi/isci/probe_roms.h')
-rw-r--r--drivers/scsi/isci/probe_roms.h89
1 files changed, 86 insertions, 3 deletions
diff --git a/drivers/scsi/isci/probe_roms.h b/drivers/scsi/isci/probe_roms.h
index 2c75248ca326..bb0e9d4d97c9 100644
--- a/drivers/scsi/isci/probe_roms.h
+++ b/drivers/scsi/isci/probe_roms.h
@@ -152,7 +152,7 @@ struct sci_user_parameters {
#define MAX_CONCURRENT_DEVICE_SPIN_UP_COUNT 4
struct sci_oem_params;
-int sci_oem_parameters_validate(struct sci_oem_params *oem);
+int sci_oem_parameters_validate(struct sci_oem_params *oem, u8 version);
struct isci_orom;
struct isci_orom *isci_request_oprom(struct pci_dev *pdev);
@@ -191,6 +191,11 @@ struct isci_oem_hdr {
0x1a, 0x04, 0xc6)
#define ISCI_EFI_VAR_NAME "RstScuO"
+#define ISCI_ROM_VER_1_0 0x10
+#define ISCI_ROM_VER_1_1 0x11
+#define ISCI_ROM_VER_1_3 0x13
+#define ISCI_ROM_VER_LATEST ISCI_ROM_VER_1_3
+
/* Allowed PORT configuration modes APC Automatic PORT configuration mode is
* defined by the OEM configuration parameters providing no PHY_MASK parameters
* for any PORT. i.e. There are no phys assigned to any of the ports at start.
@@ -220,8 +225,86 @@ struct sci_oem_params {
struct {
uint8_t mode_type;
uint8_t max_concurr_spin_up;
- uint8_t do_enable_ssc;
- uint8_t reserved;
+ /*
+ * This bitfield indicates the OEM's desired default Tx
+ * Spread Spectrum Clocking (SSC) settings for SATA and SAS.
+ * NOTE: Default SSC Modulation Frequency is 31.5KHz.
+ */
+ union {
+ struct {
+ /*
+ * NOTE: Max spread for SATA is +0 / -5000 PPM.
+ * Down-spreading SSC (only method allowed for SATA):
+ * SATA SSC Tx Disabled = 0x0
+ * SATA SSC Tx at +0 / -1419 PPM Spread = 0x2
+ * SATA SSC Tx at +0 / -2129 PPM Spread = 0x3
+ * SATA SSC Tx at +0 / -4257 PPM Spread = 0x6
+ * SATA SSC Tx at +0 / -4967 PPM Spread = 0x7
+ */
+ uint8_t ssc_sata_tx_spread_level:4;
+ /*
+ * SAS SSC Tx Disabled = 0x0
+ *
+ * NOTE: Max spread for SAS down-spreading +0 /
+ * -2300 PPM
+ * Down-spreading SSC:
+ * SAS SSC Tx at +0 / -1419 PPM Spread = 0x2
+ * SAS SSC Tx at +0 / -2129 PPM Spread = 0x3
+ *
+ * NOTE: Max spread for SAS center-spreading +2300 /
+ * -2300 PPM
+ * Center-spreading SSC:
+ * SAS SSC Tx at +1064 / -1064 PPM Spread = 0x3
+ * SAS SSC Tx at +2129 / -2129 PPM Spread = 0x6
+ */
+ uint8_t ssc_sas_tx_spread_level:3;
+ /*
+ * NOTE: Refer to the SSC section of the SAS 2.x
+ * Specification for proper setting of this field.
+ * For standard SAS Initiator SAS PHY operation it
+ * should be 0 for Down-spreading.
+ * SAS SSC Tx spread type:
+ * Down-spreading SSC = 0
+ * Center-spreading SSC = 1
+ */
+ uint8_t ssc_sas_tx_type:1;
+ };
+ uint8_t do_enable_ssc;
+ };
+ /*
+ * This field indicates length of the SAS/SATA cable between
+ * host and device.
+ * This field is used make relationship between analog
+ * parameters of the phy in the silicon and length of the cable.
+ * Supported cable attenuation levels:
+ * "short"- up to 3m, "medium"-3m to 6m, and "long"- more than
+ * 6m.
+ *
+ * This is bit mask field:
+ *
+ * BIT: (MSB) 7 6 5 4
+ * ASSIGNMENT: <phy3><phy2><phy1><phy0> - Medium cable
+ * length assignment
+ * BIT: 3 2 1 0 (LSB)
+ * ASSIGNMENT: <phy3><phy2><phy1><phy0> - Long cable length
+ * assignment
+ *
+ * BITS 7-4 are set when the cable length is assigned to medium
+ * BITS 3-0 are set when the cable length is assigned to long
+ *
+ * The BIT positions are clear when the cable length is
+ * assigned to short.
+ *
+ * Setting the bits for both long and medium cable length is
+ * undefined.
+ *
+ * A value of 0x84 would assign
+ * phy3 - medium
+ * phy2 - long
+ * phy1 - short
+ * phy0 - short
+ */
+ uint8_t cable_selection_mask;
} controller;
struct {