diff options
Diffstat (limited to 'drivers/usb/core/hub.c')
-rw-r--r-- | drivers/usb/core/hub.c | 74 |
1 files changed, 55 insertions, 19 deletions
diff --git a/drivers/usb/core/hub.c b/drivers/usb/core/hub.c index 96c66d719c89..829d3e80af7e 100644 --- a/drivers/usb/core/hub.c +++ b/drivers/usb/core/hub.c @@ -361,7 +361,8 @@ static void usb_set_lpm_parameters(struct usb_device *udev) } /* USB 2.0 spec Section 11.24.4.5 */ -static int get_hub_descriptor(struct usb_device *hdev, void *data) +static int get_hub_descriptor(struct usb_device *hdev, + struct usb_hub_descriptor *desc) { int i, ret, size; unsigned dtype; @@ -377,10 +378,18 @@ static int get_hub_descriptor(struct usb_device *hdev, void *data) for (i = 0; i < 3; i++) { ret = usb_control_msg(hdev, usb_rcvctrlpipe(hdev, 0), USB_REQ_GET_DESCRIPTOR, USB_DIR_IN | USB_RT_HUB, - dtype << 8, 0, data, size, + dtype << 8, 0, desc, size, USB_CTRL_GET_TIMEOUT); - if (ret >= (USB_DT_HUB_NONVAR_SIZE + 2)) + if (hub_is_superspeed(hdev)) { + if (ret == size) + return ret; + } else if (ret >= USB_DT_HUB_NONVAR_SIZE + 2) { + /* Make sure we have the DeviceRemovable field. */ + size = USB_DT_HUB_NONVAR_SIZE + desc->bNbrPorts / 8 + 1; + if (ret < size) + return -EMSGSIZE; return ret; + } } return -EINVAL; } @@ -1065,6 +1074,9 @@ static void hub_activate(struct usb_hub *hub, enum hub_activation_type type) portstatus = portchange = 0; status = hub_port_status(hub, port1, &portstatus, &portchange); + if (status) + goto abort; + if (udev || (portstatus & USB_PORT_STAT_CONNECTION)) dev_dbg(&port_dev->dev, "status %04x change %04x\n", portstatus, portchange); @@ -1201,7 +1213,7 @@ static void hub_activate(struct usb_hub *hub, enum hub_activation_type type) /* Scan all ports that need attention */ kick_hub_wq(hub); - + abort: if (type == HUB_INIT2 || type == HUB_INIT3) { /* Allow autosuspend if it was suppressed */ disconnected: @@ -1313,7 +1325,7 @@ static int hub_configure(struct usb_hub *hub, } mutex_init(&hub->status_mutex); - hub->descriptor = kmalloc(sizeof(*hub->descriptor), GFP_KERNEL); + hub->descriptor = kzalloc(sizeof(*hub->descriptor), GFP_KERNEL); if (!hub->descriptor) { ret = -ENOMEM; goto fail; @@ -1321,13 +1333,19 @@ static int hub_configure(struct usb_hub *hub, /* Request the entire hub descriptor. * hub->descriptor can handle USB_MAXCHILDREN ports, - * but the hub can/will return fewer bytes here. + * but a (non-SS) hub can/will return fewer bytes here. */ ret = get_hub_descriptor(hdev, hub->descriptor); if (ret < 0) { message = "can't read hub descriptor"; goto fail; - } else if (hub->descriptor->bNbrPorts > USB_MAXCHILDREN) { + } + + maxchild = USB_MAXCHILDREN; + if (hub_is_superspeed(hdev)) + maxchild = min_t(unsigned, maxchild, USB_SS_MAXPORTS); + + if (hub->descriptor->bNbrPorts > maxchild) { message = "hub has too many ports!"; ret = -ENODEV; goto fail; @@ -2087,6 +2105,12 @@ void usb_disconnect(struct usb_device **pdev) dev_info(&udev->dev, "USB disconnect, device number %d\n", udev->devnum); + /* + * Ensure that the pm runtime code knows that the USB device + * is in the process of being disconnected. + */ + pm_runtime_barrier(&udev->dev); + usb_lock_device(udev); hub_disconnect_children(udev); @@ -2664,8 +2688,15 @@ static int hub_port_wait_reset(struct usb_hub *hub, int port1, if (ret < 0) return ret; - /* The port state is unknown until the reset completes. */ - if (!(portstatus & USB_PORT_STAT_RESET)) + /* + * The port state is unknown until the reset completes. + * + * On top of that, some chips may require additional time + * to re-establish a connection after the reset is complete, + * so also wait for the connection to be re-established. + */ + if (!(portstatus & USB_PORT_STAT_RESET) && + (portstatus & USB_PORT_STAT_CONNECTION)) break; /* switch to the long delay after two short delay failures */ @@ -2687,13 +2718,16 @@ static int hub_port_wait_reset(struct usb_hub *hub, int port1, if (!(portstatus & USB_PORT_STAT_CONNECTION)) return -ENOTCONN; - /* bomb out completely if the connection bounced. A USB 3.0 - * connection may bounce if multiple warm resets were issued, + /* Retry if connect change is set but status is still connected. + * A USB 3.0 connection may bounce if multiple warm resets were issued, * but the device may have successfully re-connected. Ignore it. */ if (!hub_is_superspeed(hub->hdev) && - (portchange & USB_PORT_STAT_C_CONNECTION)) - return -ENOTCONN; + (portchange & USB_PORT_STAT_C_CONNECTION)) { + usb_clear_port_feature(hub->hdev, port1, + USB_PORT_FEAT_C_CONNECTION); + return -EAGAIN; + } if (!(portstatus & USB_PORT_STAT_ENABLE)) return -EBUSY; @@ -4280,7 +4314,7 @@ static void hub_set_initial_usb2_lpm_policy(struct usb_device *udev) struct usb_hub *hub = usb_hub_to_struct_hub(udev->parent); int connect_type = USB_PORT_CONNECT_TYPE_UNKNOWN; - if (!udev->usb2_hw_lpm_capable) + if (!udev->usb2_hw_lpm_capable || !udev->bos) return; if (hub) @@ -4712,7 +4746,8 @@ hub_power_remaining(struct usb_hub *hub) static void hub_port_connect(struct usb_hub *hub, int port1, u16 portstatus, u16 portchange) { - int status, i; + int status = -ENODEV; + int i; unsigned unit_load; struct usb_device *hdev = hub->hdev; struct usb_hcd *hcd = bus_to_hcd(hdev->bus); @@ -4811,7 +4846,7 @@ static void hub_port_connect(struct usb_hub *hub, int port1, u16 portstatus, goto loop; if (udev->quirks & USB_QUIRK_DELAY_INIT) - msleep(1000); + msleep(2000); /* consecutive bus-powered hubs aren't reliable; they can * violate the voltage drop budget. if the new child has @@ -4916,9 +4951,10 @@ loop: done: hub_port_disable(hub, port1, 1); - if (hcd->driver->relinquish_port && !hub->hdev->parent) - hcd->driver->relinquish_port(hcd, port1); - + if (hcd->driver->relinquish_port && !hub->hdev->parent) { + if (status != -ENOTCONN && status != -ENODEV) + hcd->driver->relinquish_port(hcd, port1); + } } /* Handle physical or logical connection change events. |