diff options
Diffstat (limited to 'drivers/usb/host/xhci.c')
| -rw-r--r-- | drivers/usb/host/xhci.c | 258 |
1 files changed, 245 insertions, 13 deletions
diff --git a/drivers/usb/host/xhci.c b/drivers/usb/host/xhci.c index 8f2a56ece44f..06e7023258d0 100644 --- a/drivers/usb/host/xhci.c +++ b/drivers/usb/host/xhci.c @@ -430,12 +430,19 @@ int xhci_run(struct usb_hcd *hcd) free_irq(hcd->irq, hcd); hcd->irq = -1; + /* Some Fresco Logic host controllers advertise MSI, but fail to + * generate interrupts. Don't even try to enable MSI. + */ + if (xhci->quirks & XHCI_BROKEN_MSI) + goto legacy_irq; + ret = xhci_setup_msix(xhci); if (ret) /* fall back to msi*/ ret = xhci_setup_msi(xhci); if (ret) { +legacy_irq: /* fall back to legacy interrupt*/ ret = request_irq(pdev->irq, &usb_hcd_irq, IRQF_SHARED, hcd->irq_descr, hcd); @@ -1314,8 +1321,10 @@ int xhci_drop_endpoint(struct usb_hcd *hcd, struct usb_device *udev, if (ret <= 0) return ret; xhci = hcd_to_xhci(hcd); - xhci_dbg(xhci, "%s called for udev %p\n", __func__, udev); + if (xhci->xhc_state & XHCI_STATE_DYING) + return -ENODEV; + xhci_dbg(xhci, "%s called for udev %p\n", __func__, udev); drop_flag = xhci_get_endpoint_flag(&ep->desc); if (drop_flag == SLOT_FLAG || drop_flag == EP0_FLAG) { xhci_dbg(xhci, "xHCI %s - can't drop slot or ep 0 %#x\n", @@ -1401,6 +1410,8 @@ int xhci_add_endpoint(struct usb_hcd *hcd, struct usb_device *udev, return ret; } xhci = hcd_to_xhci(hcd); + if (xhci->xhc_state & XHCI_STATE_DYING) + return -ENODEV; added_ctxs = xhci_get_endpoint_flag(&ep->desc); last_ctx = xhci_last_valid_endpoint(added_ctxs); @@ -1578,6 +1589,113 @@ static int xhci_evaluate_context_result(struct xhci_hcd *xhci, return ret; } +static u32 xhci_count_num_new_endpoints(struct xhci_hcd *xhci, + struct xhci_container_ctx *in_ctx) +{ + struct xhci_input_control_ctx *ctrl_ctx; + u32 valid_add_flags; + u32 valid_drop_flags; + + ctrl_ctx = xhci_get_input_control_ctx(xhci, in_ctx); + /* Ignore the slot flag (bit 0), and the default control endpoint flag + * (bit 1). The default control endpoint is added during the Address + * Device command and is never removed until the slot is disabled. + */ + valid_add_flags = ctrl_ctx->add_flags >> 2; + valid_drop_flags = ctrl_ctx->drop_flags >> 2; + + /* Use hweight32 to count the number of ones in the add flags, or + * number of endpoints added. Don't count endpoints that are changed + * (both added and dropped). + */ + return hweight32(valid_add_flags) - + hweight32(valid_add_flags & valid_drop_flags); +} + +static unsigned int xhci_count_num_dropped_endpoints(struct xhci_hcd *xhci, + struct xhci_container_ctx *in_ctx) +{ + struct xhci_input_control_ctx *ctrl_ctx; + u32 valid_add_flags; + u32 valid_drop_flags; + + ctrl_ctx = xhci_get_input_control_ctx(xhci, in_ctx); + valid_add_flags = ctrl_ctx->add_flags >> 2; + valid_drop_flags = ctrl_ctx->drop_flags >> 2; + + return hweight32(valid_drop_flags) - + hweight32(valid_add_flags & valid_drop_flags); +} + +/* + * We need to reserve the new number of endpoints before the configure endpoint + * command completes. We can't subtract the dropped endpoints from the number + * of active endpoints until the command completes because we can oversubscribe + * the host in this case: + * + * - the first configure endpoint command drops more endpoints than it adds + * - a second configure endpoint command that adds more endpoints is queued + * - the first configure endpoint command fails, so the config is unchanged + * - the second command may succeed, even though there isn't enough resources + * + * Must be called with xhci->lock held. + */ +static int xhci_reserve_host_resources(struct xhci_hcd *xhci, + struct xhci_container_ctx *in_ctx) +{ + u32 added_eps; + + added_eps = xhci_count_num_new_endpoints(xhci, in_ctx); + if (xhci->num_active_eps + added_eps > xhci->limit_active_eps) { + xhci_dbg(xhci, "Not enough ep ctxs: " + "%u active, need to add %u, limit is %u.\n", + xhci->num_active_eps, added_eps, + xhci->limit_active_eps); + return -ENOMEM; + } + xhci->num_active_eps += added_eps; + xhci_dbg(xhci, "Adding %u ep ctxs, %u now active.\n", added_eps, + xhci->num_active_eps); + return 0; +} + +/* + * The configure endpoint was failed by the xHC for some other reason, so we + * need to revert the resources that failed configuration would have used. + * + * Must be called with xhci->lock held. + */ +static void xhci_free_host_resources(struct xhci_hcd *xhci, + struct xhci_container_ctx *in_ctx) +{ + u32 num_failed_eps; + + num_failed_eps = xhci_count_num_new_endpoints(xhci, in_ctx); + xhci->num_active_eps -= num_failed_eps; + xhci_dbg(xhci, "Removing %u failed ep ctxs, %u now active.\n", + num_failed_eps, + xhci->num_active_eps); +} + +/* + * Now that the command has completed, clean up the active endpoint count by + * subtracting out the endpoints that were dropped (but not changed). + * + * Must be called with xhci->lock held. + */ +static void xhci_finish_resource_reservation(struct xhci_hcd *xhci, + struct xhci_container_ctx *in_ctx) +{ + u32 num_dropped_eps; + + num_dropped_eps = xhci_count_num_dropped_endpoints(xhci, in_ctx); + xhci->num_active_eps -= num_dropped_eps; + if (num_dropped_eps) + xhci_dbg(xhci, "Removing %u dropped ep ctxs, %u now active.\n", + num_dropped_eps, + xhci->num_active_eps); +} + /* Issue a configure endpoint command or evaluate context command * and wait for it to finish. */ @@ -1598,6 +1716,15 @@ static int xhci_configure_endpoint(struct xhci_hcd *xhci, virt_dev = xhci->devs[udev->slot_id]; if (command) { in_ctx = command->in_ctx; + if ((xhci->quirks & XHCI_EP_LIMIT_QUIRK) && + xhci_reserve_host_resources(xhci, in_ctx)) { + spin_unlock_irqrestore(&xhci->lock, flags); + xhci_warn(xhci, "Not enough host resources, " + "active endpoint contexts = %u\n", + xhci->num_active_eps); + return -ENOMEM; + } + cmd_completion = command->completion; cmd_status = &command->status; command->command_trb = xhci->cmd_ring->enqueue; @@ -1613,6 +1740,14 @@ static int xhci_configure_endpoint(struct xhci_hcd *xhci, list_add_tail(&command->cmd_list, &virt_dev->cmd_list); } else { in_ctx = virt_dev->in_ctx; + if ((xhci->quirks & XHCI_EP_LIMIT_QUIRK) && + xhci_reserve_host_resources(xhci, in_ctx)) { + spin_unlock_irqrestore(&xhci->lock, flags); + xhci_warn(xhci, "Not enough host resources, " + "active endpoint contexts = %u\n", + xhci->num_active_eps); + return -ENOMEM; + } cmd_completion = &virt_dev->cmd_completion; cmd_status = &virt_dev->cmd_status; } @@ -1627,6 +1762,8 @@ static int xhci_configure_endpoint(struct xhci_hcd *xhci, if (ret < 0) { if (command) list_del(&command->cmd_list); + if ((xhci->quirks & XHCI_EP_LIMIT_QUIRK)) + xhci_free_host_resources(xhci, in_ctx); spin_unlock_irqrestore(&xhci->lock, flags); xhci_dbg(xhci, "FIXME allocate a new ring segment\n"); return -ENOMEM; @@ -1649,8 +1786,22 @@ static int xhci_configure_endpoint(struct xhci_hcd *xhci, } if (!ctx_change) - return xhci_configure_endpoint_result(xhci, udev, cmd_status); - return xhci_evaluate_context_result(xhci, udev, cmd_status); + ret = xhci_configure_endpoint_result(xhci, udev, cmd_status); + else + ret = xhci_evaluate_context_result(xhci, udev, cmd_status); + + if ((xhci->quirks & XHCI_EP_LIMIT_QUIRK)) { + spin_lock_irqsave(&xhci->lock, flags); + /* If the command failed, remove the reserved resources. + * Otherwise, clean up the estimate to include dropped eps. + */ + if (ret) + xhci_free_host_resources(xhci, in_ctx); + else + xhci_finish_resource_reservation(xhci, in_ctx); + spin_unlock_irqrestore(&xhci->lock, flags); + } + return ret; } /* Called after one or more calls to xhci_add_endpoint() or @@ -1676,6 +1827,8 @@ int xhci_check_bandwidth(struct usb_hcd *hcd, struct usb_device *udev) if (ret <= 0) return ret; xhci = hcd_to_xhci(hcd); + if (xhci->xhc_state & XHCI_STATE_DYING) + return -ENODEV; xhci_dbg(xhci, "%s called for udev %p\n", __func__, udev); virt_dev = xhci->devs[udev->slot_id]; @@ -1703,8 +1856,8 @@ int xhci_check_bandwidth(struct usb_hcd *hcd, struct usb_device *udev) /* Free any rings that were dropped, but not changed. */ for (i = 1; i < 31; ++i) { - if ((ctrl_ctx->drop_flags & (1 << (i + 1))) && - !(ctrl_ctx->add_flags & (1 << (i + 1)))) + if ((le32_to_cpu(ctrl_ctx->drop_flags) & (1 << (i + 1))) && + !(le32_to_cpu(ctrl_ctx->add_flags) & (1 << (i + 1)))) xhci_free_or_cache_endpoint_ring(xhci, virt_dev, i); } xhci_zero_in_ctx(xhci, virt_dev); @@ -2266,6 +2419,34 @@ int xhci_free_streams(struct usb_hcd *hcd, struct usb_device *udev, } /* + * Deletes endpoint resources for endpoints that were active before a Reset + * Device command, or a Disable Slot command. The Reset Device command leaves + * the control endpoint intact, whereas the Disable Slot command deletes it. + * + * Must be called with xhci->lock held. + */ +void xhci_free_device_endpoint_resources(struct xhci_hcd *xhci, + struct xhci_virt_device *virt_dev, bool drop_control_ep) +{ + int i; + unsigned int num_dropped_eps = 0; + unsigned int drop_flags = 0; + + for (i = (drop_control_ep ? 0 : 1); i < 31; i++) { + if (virt_dev->eps[i].ring) { + drop_flags |= 1 << i; + num_dropped_eps++; + } + } + xhci->num_active_eps -= num_dropped_eps; + if (num_dropped_eps) + xhci_dbg(xhci, "Dropped %u ep ctxs, flags = 0x%x, " + "%u now active.\n", + num_dropped_eps, drop_flags, + xhci->num_active_eps); +} + +/* * This submits a Reset Device Command, which will set the device state to 0, * set the device address to 0, and disable all the endpoints except the default * control endpoint. The USB core should come back and call @@ -2293,6 +2474,7 @@ int xhci_discover_or_reset_device(struct usb_hcd *hcd, struct usb_device *udev) struct xhci_command *reset_device_cmd; int timeleft; int last_freed_endpoint; + struct xhci_slot_ctx *slot_ctx; ret = xhci_check_args(hcd, udev, NULL, 0, false, __func__); if (ret <= 0) @@ -2325,6 +2507,12 @@ int xhci_discover_or_reset_device(struct usb_hcd *hcd, struct usb_device *udev) return -EINVAL; } + /* If device is not setup, there is no point in resetting it */ + slot_ctx = xhci_get_slot_ctx(xhci, virt_dev->out_ctx); + if (GET_SLOT_STATE(le32_to_cpu(slot_ctx->dev_state)) == + SLOT_STATE_DISABLED) + return 0; + xhci_dbg(xhci, "Resetting device with slot ID %u\n", slot_id); /* Allocate the command structure that holds the struct completion. * Assume we're in process context, since the normal device reset @@ -2406,6 +2594,14 @@ int xhci_discover_or_reset_device(struct usb_hcd *hcd, struct usb_device *udev) goto command_cleanup; } + /* Free up host controller endpoint resources */ + if ((xhci->quirks & XHCI_EP_LIMIT_QUIRK)) { + spin_lock_irqsave(&xhci->lock, flags); + /* Don't delete the default control endpoint resources */ + xhci_free_device_endpoint_resources(xhci, virt_dev, false); + spin_unlock_irqrestore(&xhci->lock, flags); + } + /* Everything but endpoint 0 is disabled, so free or cache the rings. */ last_freed_endpoint = 1; for (i = 1; i < 31; ++i) { @@ -2479,6 +2675,27 @@ void xhci_free_dev(struct usb_hcd *hcd, struct usb_device *udev) } /* + * Checks if we have enough host controller resources for the default control + * endpoint. + * + * Must be called with xhci->lock held. + */ +static int xhci_reserve_host_control_ep_resources(struct xhci_hcd *xhci) +{ + if (xhci->num_active_eps + 1 > xhci->limit_active_eps) { + xhci_dbg(xhci, "Not enough ep ctxs: " + "%u active, need to add 1, limit is %u.\n", + xhci->num_active_eps, xhci->limit_active_eps); + return -ENOMEM; + } + xhci->num_active_eps += 1; + xhci_dbg(xhci, "Adding 1 ep ctx, %u now active.\n", + xhci->num_active_eps); + return 0; +} + + +/* * Returns 0 if the xHC ran out of device slots, the Enable Slot command * timed out, or allocating memory failed. Returns 1 on success. */ @@ -2513,24 +2730,39 @@ int xhci_alloc_dev(struct usb_hcd *hcd, struct usb_device *udev) xhci_err(xhci, "Error while assigning device slot ID\n"); return 0; } - /* xhci_alloc_virt_device() does not touch rings; no need to lock. - * Use GFP_NOIO, since this function can be called from + + if ((xhci->quirks & XHCI_EP_LIMIT_QUIRK)) { + spin_lock_irqsave(&xhci->lock, flags); + ret = xhci_reserve_host_control_ep_resources(xhci); + if (ret) { + spin_unlock_irqrestore(&xhci->lock, flags); + xhci_warn(xhci, "Not enough host resources, " + "active endpoint contexts = %u\n", + xhci->num_active_eps); + goto disable_slot; + } + spin_unlock_irqrestore(&xhci->lock, flags); + } + /* Use GFP_NOIO, since this function can be called from * xhci_discover_or_reset_device(), which may be called as part of * mass storage driver error handling. */ if (!xhci_alloc_virt_device(xhci, xhci->slot_id, udev, GFP_NOIO)) { - /* Disable slot, if we can do it without mem alloc */ xhci_warn(xhci, "Could not allocate xHCI USB device data structures\n"); - spin_lock_irqsave(&xhci->lock, flags); - if (!xhci_queue_slot_control(xhci, TRB_DISABLE_SLOT, udev->slot_id)) - xhci_ring_cmd_db(xhci); - spin_unlock_irqrestore(&xhci->lock, flags); - return 0; + goto disable_slot; } udev->slot_id = xhci->slot_id; /* Is this a LS or FS device under a HS hub? */ /* Hub or peripherial? */ return 1; + +disable_slot: + /* Disable slot, if we can do it without mem alloc */ + spin_lock_irqsave(&xhci->lock, flags); + if (!xhci_queue_slot_control(xhci, TRB_DISABLE_SLOT, udev->slot_id)) + xhci_ring_cmd_db(xhci); + spin_unlock_irqrestore(&xhci->lock, flags); + return 0; } /* |