diff options
Diffstat (limited to 'include/linux/amba')
| -rw-r--r-- | include/linux/amba/bus.h | 11 | ||||
| -rw-r--r-- | include/linux/amba/mmci.h | 27 | ||||
| -rw-r--r-- | include/linux/amba/pl022.h | 32 | ||||
| -rw-r--r-- | include/linux/amba/pl330.h | 45 | ||||
| -rw-r--r-- | include/linux/amba/serial.h | 3 |
5 files changed, 115 insertions, 3 deletions
diff --git a/include/linux/amba/bus.h b/include/linux/amba/bus.h index 8b1038607831..b0c174012436 100644 --- a/include/linux/amba/bus.h +++ b/include/linux/amba/bus.h @@ -14,14 +14,19 @@ #ifndef ASMARM_AMBA_H #define ASMARM_AMBA_H +#include <linux/clk.h> #include <linux/device.h> +#include <linux/err.h> #include <linux/resource.h> #define AMBA_NR_IRQS 2 +struct clk; + struct amba_device { struct device dev; struct resource res; + struct clk *pclk; u64 dma_mask; unsigned int periphid; unsigned int irq[AMBA_NR_IRQS]; @@ -59,6 +64,12 @@ struct amba_device *amba_find_device(const char *, struct device *, unsigned int int amba_request_regions(struct amba_device *, const char *); void amba_release_regions(struct amba_device *); +#define amba_pclk_enable(d) \ + (IS_ERR((d)->pclk) ? 0 : clk_enable((d)->pclk)) + +#define amba_pclk_disable(d) \ + do { if (!IS_ERR((d)->pclk)) clk_disable((d)->pclk); } while (0) + #define amba_config(d) (((d)->periphid >> 24) & 0xff) #define amba_rev(d) (((d)->periphid >> 20) & 0x0f) #define amba_manf(d) (((d)->periphid >> 12) & 0xff) diff --git a/include/linux/amba/mmci.h b/include/linux/amba/mmci.h index 6b4241748dda..ca84ce70d5d5 100644 --- a/include/linux/amba/mmci.h +++ b/include/linux/amba/mmci.h @@ -6,9 +6,32 @@ #include <linux/mmc/host.h> +/** + * struct mmci_platform_data - platform configuration for the MMCI + * (also known as PL180) block. + * @f_max: the maximum operational frequency for this host in this + * platform configuration. When this is specified it takes precedence + * over the module parameter for the same frequency. + * @ocr_mask: available voltages on the 4 pins from the block, this + * is ignored if a regulator is used, see the MMC_VDD_* masks in + * mmc/host.h + * @vdd_handler: a callback function to translate a MMC_VDD_* + * mask into a value to be binary (or set some other custom bits + * in MMCIPWR) or:ed and written into the MMCIPWR register of the + * block. May also control external power based on the power_mode. + * @status: if no GPIO read function was given to the block in + * gpio_wp (below) this function will be called to determine + * whether a card is present in the MMC slot or not + * @gpio_wp: read this GPIO pin to see if the card is write protected + * @gpio_cd: read this GPIO pin to detect card insertion + * @capabilities: the capabilities of the block as implemented in + * this platform, signify anything MMC_CAP_* from mmc/host.h + */ struct mmci_platform_data { - unsigned int ocr_mask; /* available voltages */ - u32 (*translate_vdd)(struct device *, unsigned int); + unsigned int f_max; + unsigned int ocr_mask; + u32 (*vdd_handler)(struct device *, unsigned int vdd, + unsigned char power_mode); unsigned int (*status)(struct device *); int gpio_wp; int gpio_cd; diff --git a/include/linux/amba/pl022.h b/include/linux/amba/pl022.h index e4836c6b3dd7..abf26cc47a2b 100644 --- a/include/linux/amba/pl022.h +++ b/include/linux/amba/pl022.h @@ -71,6 +71,7 @@ struct ssp_clock_params { /** * enum ssp_rx_endian - endianess of Rx FIFO Data + * this feature is only available in ST versionf of PL022 */ enum ssp_rx_endian { SSP_RX_MSB, @@ -181,7 +182,8 @@ enum ssp_microwire_wait_state { }; /** - * enum Microwire - whether Full/Half Duplex + * enum ssp_duplex - whether Full/Half Duplex on microwire, only + * available in the ST Micro variant. * @SSP_MICROWIRE_CHANNEL_FULL_DUPLEX: SSPTXD becomes bi-directional, * SSPRXD not used * @SSP_MICROWIRE_CHANNEL_HALF_DUPLEX: SSPTXD is an output, SSPRXD is @@ -193,6 +195,31 @@ enum ssp_duplex { }; /** + * enum ssp_clkdelay - an optional clock delay on the feedback clock + * only available in the ST Micro PL023 variant. + * @SSP_FEEDBACK_CLK_DELAY_NONE: no delay, the data coming in from the + * slave is sampled directly + * @SSP_FEEDBACK_CLK_DELAY_1T: the incoming slave data is sampled with + * a delay of T-dt + * @SSP_FEEDBACK_CLK_DELAY_2T: dito with a delay if 2T-dt + * @SSP_FEEDBACK_CLK_DELAY_3T: dito with a delay if 3T-dt + * @SSP_FEEDBACK_CLK_DELAY_4T: dito with a delay if 4T-dt + * @SSP_FEEDBACK_CLK_DELAY_5T: dito with a delay if 5T-dt + * @SSP_FEEDBACK_CLK_DELAY_6T: dito with a delay if 6T-dt + * @SSP_FEEDBACK_CLK_DELAY_7T: dito with a delay if 7T-dt + */ +enum ssp_clkdelay { + SSP_FEEDBACK_CLK_DELAY_NONE, + SSP_FEEDBACK_CLK_DELAY_1T, + SSP_FEEDBACK_CLK_DELAY_2T, + SSP_FEEDBACK_CLK_DELAY_3T, + SSP_FEEDBACK_CLK_DELAY_4T, + SSP_FEEDBACK_CLK_DELAY_5T, + SSP_FEEDBACK_CLK_DELAY_6T, + SSP_FEEDBACK_CLK_DELAY_7T +}; + +/** * CHIP select/deselect commands */ enum ssp_chip_select { @@ -235,6 +262,8 @@ struct pl022_ssp_controller { * @ctrl_len: Microwire interface: Control length * @wait_state: Microwire interface: Wait state * @duplex: Microwire interface: Full/Half duplex + * @clkdelay: on the PL023 variant, the delay in feeback clock cycles + * before sampling the incoming line * @cs_control: function pointer to board-specific function to * assert/deassert I/O port to control HW generation of devices chip-select. * @dma_xfer_type: Type of DMA xfer (Mem-to-periph or Periph-to-Periph) @@ -258,6 +287,7 @@ struct pl022_config_chip { enum ssp_microwire_ctrl_len ctrl_len; enum ssp_microwire_wait_state wait_state; enum ssp_duplex duplex; + enum ssp_clkdelay clkdelay; void (*cs_control) (u32 control); }; diff --git a/include/linux/amba/pl330.h b/include/linux/amba/pl330.h new file mode 100644 index 000000000000..cbee7de7dd36 --- /dev/null +++ b/include/linux/amba/pl330.h @@ -0,0 +1,45 @@ +/* linux/include/linux/amba/pl330.h + * + * Copyright (C) 2010 Samsung Electronics Co. Ltd. + * Jaswinder Singh <jassi.brar@samsung.com> + * + * This program is free software; you can redistribute it and/or modify + * it under the terms of the GNU General Public License as published by + * the Free Software Foundation; either version 2 of the License, or + * (at your option) any later version. + */ + +#ifndef __AMBA_PL330_H_ +#define __AMBA_PL330_H_ + +#include <asm/hardware/pl330.h> + +struct dma_pl330_peri { + /* + * Peri_Req i/f of the DMAC that is + * peripheral could be reached from. + */ + u8 peri_id; /* {0, 31} */ + enum pl330_reqtype rqtype; + + /* For M->D and D->M Channels */ + int burst_sz; /* in power of 2 */ + dma_addr_t fifo_addr; +}; + +struct dma_pl330_platdata { + /* + * Number of valid peripherals connected to DMAC. + * This may be different from the value read from + * CR0, as the PL330 implementation might have 'holes' + * in the peri list or the peri could also be reached + * from another DMAC which the platform prefers. + */ + u8 nr_valid_peri; + /* Array of valid peripherals */ + struct dma_pl330_peri *peri; + /* Bytes to allocate for MC buffer */ + unsigned mcbuf_sz; +}; + +#endif /* __AMBA_PL330_H_ */ diff --git a/include/linux/amba/serial.h b/include/linux/amba/serial.h index 5a5a7fd62490..e1b634b635f2 100644 --- a/include/linux/amba/serial.h +++ b/include/linux/amba/serial.h @@ -38,10 +38,12 @@ #define UART01x_FR 0x18 /* Flag register (Read only). */ #define UART010_IIR 0x1C /* Interrupt indentification register (Read). */ #define UART010_ICR 0x1C /* Interrupt clear register (Write). */ +#define ST_UART011_LCRH_RX 0x1C /* Rx line control register. */ #define UART01x_ILPR 0x20 /* IrDA low power counter register. */ #define UART011_IBRD 0x24 /* Integer baud rate divisor register. */ #define UART011_FBRD 0x28 /* Fractional baud rate divisor register. */ #define UART011_LCRH 0x2c /* Line control register. */ +#define ST_UART011_LCRH_TX 0x2c /* Tx Line control register. */ #define UART011_CR 0x30 /* Control register. */ #define UART011_IFLS 0x34 /* Interrupt fifo level select. */ #define UART011_IMSC 0x38 /* Interrupt mask. */ @@ -84,6 +86,7 @@ #define UART010_CR_TIE 0x0020 #define UART010_CR_RIE 0x0010 #define UART010_CR_MSIE 0x0008 +#define ST_UART011_CR_OVSFACT 0x0008 /* Oversampling factor */ #define UART01x_CR_IIRLP 0x0004 /* SIR low power mode */ #define UART01x_CR_SIREN 0x0002 /* SIR enable */ #define UART01x_CR_UARTEN 0x0001 /* UART enable */ |