diff options
Diffstat (limited to 'include/linux/mfd')
| -rw-r--r-- | include/linux/mfd/pcf50633/core.h | 7 | ||||
| -rw-r--r-- | include/linux/mfd/pcf50633/mbc.h | 1 | ||||
| -rw-r--r-- | include/linux/mfd/tmio.h | 39 | ||||
| -rw-r--r-- | include/linux/mfd/wm831x/pdata.h | 17 | ||||
| -rw-r--r-- | include/linux/mfd/wm8350/pmic.h | 28 |
5 files changed, 77 insertions, 15 deletions
diff --git a/include/linux/mfd/pcf50633/core.h b/include/linux/mfd/pcf50633/core.h index d9034cc87f18..3398bd9aab11 100644 --- a/include/linux/mfd/pcf50633/core.h +++ b/include/linux/mfd/pcf50633/core.h @@ -29,7 +29,12 @@ struct pcf50633_platform_data { char **batteries; int num_batteries; - int charging_restart_interval; + /* + * Should be set accordingly to the reference resistor used, see + * I_{ch(ref)} charger reference current in the pcf50633 User + * Manual. + */ + int charger_reference_current_ma; /* Callbacks */ void (*probe_done)(struct pcf50633 *); diff --git a/include/linux/mfd/pcf50633/mbc.h b/include/linux/mfd/pcf50633/mbc.h index 4119579acf2c..df4f5fa88de3 100644 --- a/include/linux/mfd/pcf50633/mbc.h +++ b/include/linux/mfd/pcf50633/mbc.h @@ -128,6 +128,7 @@ enum pcf50633_reg_mbcs3 { int pcf50633_mbc_usb_curlim_set(struct pcf50633 *pcf, int ma); int pcf50633_mbc_get_status(struct pcf50633 *); +int pcf50633_mbc_get_usb_online_status(struct pcf50633 *); #endif diff --git a/include/linux/mfd/tmio.h b/include/linux/mfd/tmio.h index 6b9c5d06690c..9cb1834deffa 100644 --- a/include/linux/mfd/tmio.h +++ b/include/linux/mfd/tmio.h @@ -2,6 +2,8 @@ #define MFD_TMIO_H #include <linux/fb.h> +#include <linux/io.h> +#include <linux/platform_device.h> #define tmio_ioread8(addr) readb(addr) #define tmio_ioread16(addr) readw(addr) @@ -18,11 +20,48 @@ writew((val) >> 16, (addr) + 2); \ } while (0) +#define CNF_CMD 0x04 +#define CNF_CTL_BASE 0x10 +#define CNF_INT_PIN 0x3d +#define CNF_STOP_CLK_CTL 0x40 +#define CNF_GCLK_CTL 0x41 +#define CNF_SD_CLK_MODE 0x42 +#define CNF_PIN_STATUS 0x44 +#define CNF_PWR_CTL_1 0x48 +#define CNF_PWR_CTL_2 0x49 +#define CNF_PWR_CTL_3 0x4a +#define CNF_CARD_DETECT_MODE 0x4c +#define CNF_SD_SLOT 0x50 +#define CNF_EXT_GCLK_CTL_1 0xf0 +#define CNF_EXT_GCLK_CTL_2 0xf1 +#define CNF_EXT_GCLK_CTL_3 0xf9 +#define CNF_SD_LED_EN_1 0xfa +#define CNF_SD_LED_EN_2 0xfe + +#define SDCREN 0x2 /* Enable access to MMC CTL regs. (flag in COMMAND_REG)*/ + +#define sd_config_write8(base, shift, reg, val) \ + tmio_iowrite8((val), (base) + ((reg) << (shift))) +#define sd_config_write16(base, shift, reg, val) \ + tmio_iowrite16((val), (base) + ((reg) << (shift))) +#define sd_config_write32(base, shift, reg, val) \ + do { \ + tmio_iowrite16((val), (base) + ((reg) << (shift))); \ + tmio_iowrite16((val) >> 16, (base) + ((reg + 2) << (shift))); \ + } while (0) + +int tmio_core_mmc_enable(void __iomem *cnf, int shift, unsigned long base); +int tmio_core_mmc_resume(void __iomem *cnf, int shift, unsigned long base); +void tmio_core_mmc_pwr(void __iomem *cnf, int shift, int state); +void tmio_core_mmc_clk_div(void __iomem *cnf, int shift, int state); + /* * data for the MMC controller */ struct tmio_mmc_data { const unsigned int hclk; + void (*set_pwr)(struct platform_device *host, int state); + void (*set_clk_div)(struct platform_device *host, int state); }; /* diff --git a/include/linux/mfd/wm831x/pdata.h b/include/linux/mfd/wm831x/pdata.h index 415c228743d5..fd322aca33ba 100644 --- a/include/linux/mfd/wm831x/pdata.h +++ b/include/linux/mfd/wm831x/pdata.h @@ -41,6 +41,23 @@ struct wm831x_battery_pdata { int timeout; /** Charge cycle timeout, in minutes */ }; +/** + * Configuration for the WM831x DC-DC BuckWise convertors. This + * should be passed as driver_data in the regulator_init_data. + * + * Currently all the configuration is for the fast DVS switching + * support of the devices. This allows MFPs on the device to be + * configured as an input to switch between two output voltages, + * allowing voltage transitions without the expense of an access over + * I2C or SPI buses. + */ +struct wm831x_buckv_pdata { + int dvs_gpio; /** CPU GPIO to use for DVS switching */ + int dvs_control_src; /** Hardware DVS source to use (1 or 2) */ + int dvs_init_state; /** DVS state to expect on startup */ + int dvs_state_gpio; /** CPU GPIO to use for monitoring status */ +}; + /* Sources for status LED configuration. Values are register values * plus 1 to allow for a zero default for preserve. */ diff --git a/include/linux/mfd/wm8350/pmic.h b/include/linux/mfd/wm8350/pmic.h index be3264e286e0..e786fe9841ef 100644 --- a/include/linux/mfd/wm8350/pmic.h +++ b/include/linux/mfd/wm8350/pmic.h @@ -666,20 +666,20 @@ #define WM8350_ISINK_FLASH_DUR_64MS (1 << 8) #define WM8350_ISINK_FLASH_DUR_96MS (2 << 8) #define WM8350_ISINK_FLASH_DUR_1024MS (3 << 8) -#define WM8350_ISINK_FLASH_ON_INSTANT (0 << 4) -#define WM8350_ISINK_FLASH_ON_0_25S (1 << 4) -#define WM8350_ISINK_FLASH_ON_0_50S (2 << 4) -#define WM8350_ISINK_FLASH_ON_1_00S (3 << 4) -#define WM8350_ISINK_FLASH_ON_1_95S (1 << 4) -#define WM8350_ISINK_FLASH_ON_3_91S (2 << 4) -#define WM8350_ISINK_FLASH_ON_7_80S (3 << 4) -#define WM8350_ISINK_FLASH_OFF_INSTANT (0 << 0) -#define WM8350_ISINK_FLASH_OFF_0_25S (1 << 0) -#define WM8350_ISINK_FLASH_OFF_0_50S (2 << 0) -#define WM8350_ISINK_FLASH_OFF_1_00S (3 << 0) -#define WM8350_ISINK_FLASH_OFF_1_95S (1 << 0) -#define WM8350_ISINK_FLASH_OFF_3_91S (2 << 0) -#define WM8350_ISINK_FLASH_OFF_7_80S (3 << 0) +#define WM8350_ISINK_FLASH_ON_INSTANT (0 << 0) +#define WM8350_ISINK_FLASH_ON_0_25S (1 << 0) +#define WM8350_ISINK_FLASH_ON_0_50S (2 << 0) +#define WM8350_ISINK_FLASH_ON_1_00S (3 << 0) +#define WM8350_ISINK_FLASH_ON_1_95S (1 << 0) +#define WM8350_ISINK_FLASH_ON_3_91S (2 << 0) +#define WM8350_ISINK_FLASH_ON_7_80S (3 << 0) +#define WM8350_ISINK_FLASH_OFF_INSTANT (0 << 4) +#define WM8350_ISINK_FLASH_OFF_0_25S (1 << 4) +#define WM8350_ISINK_FLASH_OFF_0_50S (2 << 4) +#define WM8350_ISINK_FLASH_OFF_1_00S (3 << 4) +#define WM8350_ISINK_FLASH_OFF_1_95S (1 << 4) +#define WM8350_ISINK_FLASH_OFF_3_91S (2 << 4) +#define WM8350_ISINK_FLASH_OFF_7_80S (3 << 4) /* * Regulator Interrupts. |