1 files changed, 128 insertions, 0 deletions
diff --git a/include/linux/spi/spi_bitbang.h b/include/linux/spi/spi_bitbang.h
new file mode 100644
index 000000000000..8dfe61a445f4
--- /dev/null
+++ b/include/linux/spi/spi_bitbang.h
@@ -0,0 +1,128 @@
+#ifndef	__SPI_BITBANG_H
+#define	__SPI_BITBANG_H
+
+/*
+ * Mix this utility code with some glue code to get one of several types of
+ * simple SPI master driver.  Two do polled word-at-a-time I/O:
+ *
+ *   -	GPIO/parport bitbangers.  Provide chipselect() and txrx_word[](),
+ *	expanding the per-word routines from the inline templates below.
+ *
+ *   -	Drivers for controllers resembling bare shift registers.  Provide
+ *	chipselect() and txrx_word[](), with custom setup()/cleanup() methods
+ *	that use your controller's clock and chipselect registers.
+ *
+ * Some hardware works well with requests at spi_transfer scope:
+ *
+ *   -	Drivers leveraging smarter hardware, with fifos or DMA; or for half
+ *	duplex (MicroWire) controllers.  Provide chipslect() and txrx_bufs(),
+ *	and custom setup()/cleanup() methods.
+ */
+struct spi_bitbang {
+	struct workqueue_struct	*workqueue;
+	struct work_struct	work;
+
+	spinlock_t		lock;
+	struct list_head	queue;
+	u8			busy;
+	u8			shutdown;
+	u8			use_dma;
+
+	struct spi_master	*master;
+
+	void	(*chipselect)(struct spi_device *spi, int is_on);
+
+	int	(*txrx_bufs)(struct spi_device *spi, struct spi_transfer *t);
+	u32	(*txrx_word[4])(struct spi_device *spi,
+			unsigned nsecs,
+			u32 word, u8 bits);
+};
+
+/* you can call these default bitbang->master methods from your custom
+ * methods, if you like.
+ */
+extern int spi_bitbang_setup(struct spi_device *spi);
+extern void spi_bitbang_cleanup(const struct spi_device *spi);
+extern int spi_bitbang_transfer(struct spi_device *spi, struct spi_message *m);
+
+/* start or stop queue processing */
+extern int spi_bitbang_start(struct spi_bitbang *spi);
+extern int spi_bitbang_stop(struct spi_bitbang *spi);
+
+#endif	/* __SPI_BITBANG_H */
+
+/*-------------------------------------------------------------------------*/
+
+#ifdef	EXPAND_BITBANG_TXRX
+
+/*
+ * The code that knows what GPIO pins do what should have declared four
+ * functions, ideally as inlines, before #defining EXPAND_BITBANG_TXRX
+ * and including this header:
+ *
+ *  void setsck(struct spi_device *, int is_on);
+ *  void setmosi(struct spi_device *, int is_on);
+ *  int getmiso(struct spi_device *);
+ *  void spidelay(unsigned);
+ *
+ * A non-inlined routine would call bitbang_txrx_*() routines.  The
+ * main loop could easily compile down to a handful of instructions,
+ * especially if the delay is a NOP (to run at peak speed).
+ *
+ * Since this is software, the timings may not be exactly what your board's
+ * chips need ... there may be several reasons you'd need to tweak timings
+ * in these routines, not just make to make it faster or slower to match a
+ * particular CPU clock rate.
+ */
+
+static inline u32
+bitbang_txrx_be_cpha0(struct spi_device *spi,
+		unsigned nsecs, unsigned cpol,
+		u32 word, u8 bits)
+{
+	/* if (cpol == 0) this is SPI_MODE_0; else this is SPI_MODE_2 */
+
+	/* clock starts at inactive polarity */
+	for (word <<= (32 - bits); likely(bits); bits--) {
+
+		/* setup MSB (to slave) on trailing edge */
+		setmosi(spi, word & (1 << 31));
+		spidelay(nsecs);	/* T(setup) */
+
+		setsck(spi, !cpol);
+		spidelay(nsecs);
+
+		/* sample MSB (from slave) on leading edge */
+		word <<= 1;
+		word |= getmiso(spi);
+		setsck(spi, cpol);
+	}
+	return word;
+}
+
+static inline u32
+bitbang_txrx_be_cpha1(struct spi_device *spi,
+		unsigned nsecs, unsigned cpol,
+		u32 word, u8 bits)
+{
+	/* if (cpol == 0) this is SPI_MODE_1; else this is SPI_MODE_3 */
+
+	/* clock starts at inactive polarity */
+	for (word <<= (32 - bits); likely(bits); bits--) {
+
+		/* setup MSB (to slave) on leading edge */
+		setsck(spi, !cpol);
+		setmosi(spi, word & (1 << 31));
+		spidelay(nsecs); /* T(setup) */
+
+		setsck(spi, cpol);
+		spidelay(nsecs);
+
+		/* sample MSB (from slave) on trailing edge */
+		word <<= 1;
+		word |= getmiso(spi);
+	}
+	return word;
+}
+
+#endif	/* EXPAND_BITBANG_TXRX */