diff options
Diffstat (limited to 'include/linux')
| -rw-r--r-- | include/linux/amba/pl022.h | 264 | ||||
| -rw-r--r-- | include/linux/amba/serial.h | 3 | ||||
| -rw-r--r-- | include/linux/auto_fs.h | 3 | ||||
| -rw-r--r-- | include/linux/clk.h | 13 | ||||
| -rw-r--r-- | include/linux/cred.h | 1 | ||||
| -rw-r--r-- | include/linux/i7300_idle.h | 20 | ||||
| -rw-r--r-- | include/linux/input.h | 1 | ||||
| -rw-r--r-- | include/linux/net_dropmon.h | 1 | ||||
| -rw-r--r-- | include/linux/netfilter/nf_conntrack_tcp.h | 4 | ||||
| -rw-r--r-- | include/linux/parport.h | 4 | ||||
| -rw-r--r-- | include/linux/swap.h | 5 |
11 files changed, 307 insertions, 12 deletions
diff --git a/include/linux/amba/pl022.h b/include/linux/amba/pl022.h new file mode 100644 index 000000000000..dcad0ffd1755 --- /dev/null +++ b/include/linux/amba/pl022.h @@ -0,0 +1,264 @@ +/* + * include/linux/amba/pl022.h + * + * Copyright (C) 2008-2009 ST-Ericsson AB + * Copyright (C) 2006 STMicroelectronics Pvt. Ltd. + * + * Author: Linus Walleij <linus.walleij@stericsson.com> + * + * Initial version inspired by: + * linux-2.6.17-rc3-mm1/drivers/spi/pxa2xx_spi.c + * Initial adoption to PL022 by: + * Sachin Verma <sachin.verma@st.com> + * + * This program is free software; you can redistribute it and/or modify + * it under the terms of the GNU General Public License as published by + * the Free Software Foundation; either version 2 of the License, or + * (at your option) any later version. + * + * This program is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + */ + +#ifndef _SSP_PL022_H +#define _SSP_PL022_H + +#include <linux/device.h> + +/** + * whether SSP is in loopback mode or not + */ +enum ssp_loopback { + LOOPBACK_DISABLED, + LOOPBACK_ENABLED +}; + +/** + * enum ssp_interface - interfaces allowed for this SSP Controller + * @SSP_INTERFACE_MOTOROLA_SPI: Motorola Interface + * @SSP_INTERFACE_TI_SYNC_SERIAL: Texas Instrument Synchronous Serial + * interface + * @SSP_INTERFACE_NATIONAL_MICROWIRE: National Semiconductor Microwire + * interface + * @SSP_INTERFACE_UNIDIRECTIONAL: Unidirectional interface (STn8810 + * &STn8815 only) + */ +enum ssp_interface { + SSP_INTERFACE_MOTOROLA_SPI, + SSP_INTERFACE_TI_SYNC_SERIAL, + SSP_INTERFACE_NATIONAL_MICROWIRE, + SSP_INTERFACE_UNIDIRECTIONAL +}; + +/** + * enum ssp_hierarchy - whether SSP is configured as Master or Slave + */ +enum ssp_hierarchy { + SSP_MASTER, + SSP_SLAVE +}; + +/** + * enum ssp_clock_params - clock parameters, to set SSP clock at a + * desired freq + */ +struct ssp_clock_params { + u8 cpsdvsr; /* value from 2 to 254 (even only!) */ + u8 scr; /* value from 0 to 255 */ +}; + +/** + * enum ssp_rx_endian - endianess of Rx FIFO Data + */ +enum ssp_rx_endian { + SSP_RX_MSB, + SSP_RX_LSB +}; + +/** + * enum ssp_tx_endian - endianess of Tx FIFO Data + */ +enum ssp_tx_endian { + SSP_TX_MSB, + SSP_TX_LSB +}; + +/** + * enum ssp_data_size - number of bits in one data element + */ +enum ssp_data_size { + SSP_DATA_BITS_4 = 0x03, SSP_DATA_BITS_5, SSP_DATA_BITS_6, + SSP_DATA_BITS_7, SSP_DATA_BITS_8, SSP_DATA_BITS_9, + SSP_DATA_BITS_10, SSP_DATA_BITS_11, SSP_DATA_BITS_12, + SSP_DATA_BITS_13, SSP_DATA_BITS_14, SSP_DATA_BITS_15, + SSP_DATA_BITS_16, SSP_DATA_BITS_17, SSP_DATA_BITS_18, + SSP_DATA_BITS_19, SSP_DATA_BITS_20, SSP_DATA_BITS_21, + SSP_DATA_BITS_22, SSP_DATA_BITS_23, SSP_DATA_BITS_24, + SSP_DATA_BITS_25, SSP_DATA_BITS_26, SSP_DATA_BITS_27, + SSP_DATA_BITS_28, SSP_DATA_BITS_29, SSP_DATA_BITS_30, + SSP_DATA_BITS_31, SSP_DATA_BITS_32 +}; + +/** + * enum ssp_mode - SSP mode of operation (Communication modes) + */ +enum ssp_mode { + INTERRUPT_TRANSFER, + POLLING_TRANSFER, + DMA_TRANSFER +}; + +/** + * enum ssp_rx_level_trig - receive FIFO watermark level which triggers + * IT: Interrupt fires when _N_ or more elements in RX FIFO. + */ +enum ssp_rx_level_trig { + SSP_RX_1_OR_MORE_ELEM, + SSP_RX_4_OR_MORE_ELEM, + SSP_RX_8_OR_MORE_ELEM, + SSP_RX_16_OR_MORE_ELEM, + SSP_RX_32_OR_MORE_ELEM +}; + +/** + * Transmit FIFO watermark level which triggers (IT Interrupt fires + * when _N_ or more empty locations in TX FIFO) + */ +enum ssp_tx_level_trig { + SSP_TX_1_OR_MORE_EMPTY_LOC, + SSP_TX_4_OR_MORE_EMPTY_LOC, + SSP_TX_8_OR_MORE_EMPTY_LOC, + SSP_TX_16_OR_MORE_EMPTY_LOC, + SSP_TX_32_OR_MORE_EMPTY_LOC +}; + +/** + * enum SPI Clock Phase - clock phase (Motorola SPI interface only) + * @SSP_CLK_RISING_EDGE: Receive data on rising edge + * @SSP_CLK_FALLING_EDGE: Receive data on falling edge + */ +enum ssp_spi_clk_phase { + SSP_CLK_RISING_EDGE, + SSP_CLK_FALLING_EDGE +}; + +/** + * enum SPI Clock Polarity - clock polarity (Motorola SPI interface only) + * @SSP_CLK_POL_IDLE_LOW: Low inactive level + * @SSP_CLK_POL_IDLE_HIGH: High inactive level + */ +enum ssp_spi_clk_pol { + SSP_CLK_POL_IDLE_LOW, + SSP_CLK_POL_IDLE_HIGH +}; + +/** + * Microwire Conrol Lengths Command size in microwire format + */ +enum ssp_microwire_ctrl_len { + SSP_BITS_4 = 0x03, SSP_BITS_5, SSP_BITS_6, + SSP_BITS_7, SSP_BITS_8, SSP_BITS_9, + SSP_BITS_10, SSP_BITS_11, SSP_BITS_12, + SSP_BITS_13, SSP_BITS_14, SSP_BITS_15, + SSP_BITS_16, SSP_BITS_17, SSP_BITS_18, + SSP_BITS_19, SSP_BITS_20, SSP_BITS_21, + SSP_BITS_22, SSP_BITS_23, SSP_BITS_24, + SSP_BITS_25, SSP_BITS_26, SSP_BITS_27, + SSP_BITS_28, SSP_BITS_29, SSP_BITS_30, + SSP_BITS_31, SSP_BITS_32 +}; + +/** + * enum Microwire Wait State + * @SSP_MWIRE_WAIT_ZERO: No wait state inserted after last command bit + * @SSP_MWIRE_WAIT_ONE: One wait state inserted after last command bit + */ +enum ssp_microwire_wait_state { + SSP_MWIRE_WAIT_ZERO, + SSP_MWIRE_WAIT_ONE +}; + +/** + * enum Microwire - whether Full/Half Duplex + * @SSP_MICROWIRE_CHANNEL_FULL_DUPLEX: SSPTXD becomes bi-directional, + * SSPRXD not used + * @SSP_MICROWIRE_CHANNEL_HALF_DUPLEX: SSPTXD is an output, SSPRXD is + * an input. + */ +enum ssp_duplex { + SSP_MICROWIRE_CHANNEL_FULL_DUPLEX, + SSP_MICROWIRE_CHANNEL_HALF_DUPLEX +}; + +/** + * CHIP select/deselect commands + */ +enum ssp_chip_select { + SSP_CHIP_SELECT, + SSP_CHIP_DESELECT +}; + + +/** + * struct pl022_ssp_master - device.platform_data for SPI controller devices. + * @num_chipselect: chipselects are used to distinguish individual + * SPI slaves, and are numbered from zero to num_chipselects - 1. + * each slave has a chipselect signal, but it's common that not + * every chipselect is connected to a slave. + * @enable_dma: if true enables DMA driven transfers. + */ +struct pl022_ssp_controller { + u16 bus_id; + u8 num_chipselect; + u8 enable_dma:1; +}; + +/** + * struct ssp_config_chip - spi_board_info.controller_data for SPI + * slave devices, copied to spi_device.controller_data. + * + * @lbm: used for test purpose to internally connect RX and TX + * @iface: Interface type(Motorola, TI, Microwire, Universal) + * @hierarchy: sets whether interface is master or slave + * @slave_tx_disable: SSPTXD is disconnected (in slave mode only) + * @clk_freq: Tune freq parameters of SSP(when in master mode) + * @endian_rx: Endianess of Data in Rx FIFO + * @endian_tx: Endianess of Data in Tx FIFO + * @data_size: Width of data element(4 to 32 bits) + * @com_mode: communication mode: polling, Interrupt or DMA + * @rx_lev_trig: Rx FIFO watermark level (for IT & DMA mode) + * @tx_lev_trig: Tx FIFO watermark level (for IT & DMA mode) + * @clk_phase: Motorola SPI interface Clock phase + * @clk_pol: Motorola SPI interface Clock polarity + * @ctrl_len: Microwire interface: Control length + * @wait_state: Microwire interface: Wait state + * @duplex: Microwire interface: Full/Half duplex + * @cs_control: function pointer to board-specific function to + * assert/deassert I/O port to control HW generation of devices chip-select. + * @dma_xfer_type: Type of DMA xfer (Mem-to-periph or Periph-to-Periph) + * @dma_config: DMA configuration for SSP controller and peripheral + */ +struct pl022_config_chip { + struct device *dev; + enum ssp_loopback lbm; + enum ssp_interface iface; + enum ssp_hierarchy hierarchy; + bool slave_tx_disable; + struct ssp_clock_params clk_freq; + enum ssp_rx_endian endian_rx; + enum ssp_tx_endian endian_tx; + enum ssp_data_size data_size; + enum ssp_mode com_mode; + enum ssp_rx_level_trig rx_lev_trig; + enum ssp_tx_level_trig tx_lev_trig; + enum ssp_spi_clk_phase clk_phase; + enum ssp_spi_clk_pol clk_pol; + enum ssp_microwire_ctrl_len ctrl_len; + enum ssp_microwire_wait_state wait_state; + enum ssp_duplex duplex; + void (*cs_control) (u32 control); +}; + +#endif /* _SSP_PL022_H */ diff --git a/include/linux/amba/serial.h b/include/linux/amba/serial.h index 48ee32a18ac5..42949e210cb8 100644 --- a/include/linux/amba/serial.h +++ b/include/linux/amba/serial.h @@ -114,6 +114,9 @@ #define UART011_IFLS_TX4_8 (2 << 0) #define UART011_IFLS_TX6_8 (3 << 0) #define UART011_IFLS_TX7_8 (4 << 0) +/* special values for ST vendor with deeper fifo */ +#define UART011_IFLS_RX_HALF (5 << 3) +#define UART011_IFLS_TX_HALF (5 << 0) #define UART011_OEIM (1 << 10) /* overrun error interrupt mask */ #define UART011_BEIM (1 << 9) /* break error interrupt mask */ diff --git a/include/linux/auto_fs.h b/include/linux/auto_fs.h index 63265852b7d1..7b09c8348fd3 100644 --- a/include/linux/auto_fs.h +++ b/include/linux/auto_fs.h @@ -14,13 +14,12 @@ #ifndef _LINUX_AUTO_FS_H #define _LINUX_AUTO_FS_H +#include <linux/types.h> #ifdef __KERNEL__ #include <linux/fs.h> #include <linux/limits.h> -#include <linux/types.h> #include <linux/ioctl.h> #else -#include <asm/types.h> #include <sys/ioctl.h> #endif /* __KERNEL__ */ diff --git a/include/linux/clk.h b/include/linux/clk.h index 1db9bbf444a3..1d37f42ac294 100644 --- a/include/linux/clk.h +++ b/include/linux/clk.h @@ -142,4 +142,17 @@ struct clk *clk_get_parent(struct clk *clk); */ struct clk *clk_get_sys(const char *dev_id, const char *con_id); +/** + * clk_add_alias - add a new clock alias + * @alias: name for clock alias + * @alias_dev_name: device name + * @id: platform specific clock name + * @dev: device + * + * Allows using generic clock names for drivers by adding a new alias. + * Assumes clkdev, see clkdev.h for more info. + */ +int clk_add_alias(const char *alias, const char *alias_dev_name, char *id, + struct device *dev); + #endif diff --git a/include/linux/cred.h b/include/linux/cred.h index 3282ee4318e7..4fa999696310 100644 --- a/include/linux/cred.h +++ b/include/linux/cred.h @@ -13,6 +13,7 @@ #define _LINUX_CRED_H #include <linux/capability.h> +#include <linux/init.h> #include <linux/key.h> #include <asm/atomic.h> diff --git a/include/linux/i7300_idle.h b/include/linux/i7300_idle.h index 05a80c44513c..1587b7dec505 100644 --- a/include/linux/i7300_idle.h +++ b/include/linux/i7300_idle.h @@ -16,35 +16,33 @@ struct fbd_ioat { unsigned int vendor; unsigned int ioat_dev; + unsigned int enabled; }; /* * The i5000 chip-set has the same hooks as the i7300 - * but support is disabled by default because this driver - * has not been validated on that platform. + * but it is not enabled by default and must be manually + * manually enabled with "forceload=1" because it is + * only lightly validated. */ -#define SUPPORT_I5000 0 static const struct fbd_ioat fbd_ioat_list[] = { - {PCI_VENDOR_ID_INTEL, PCI_DEVICE_ID_INTEL_IOAT_CNB}, -#if SUPPORT_I5000 - {PCI_VENDOR_ID_INTEL, PCI_DEVICE_ID_INTEL_IOAT}, -#endif + {PCI_VENDOR_ID_INTEL, PCI_DEVICE_ID_INTEL_IOAT_CNB, 1}, + {PCI_VENDOR_ID_INTEL, PCI_DEVICE_ID_INTEL_IOAT, 0}, {0, 0} }; /* table of devices that work with this driver */ static const struct pci_device_id pci_tbl[] = { { PCI_DEVICE(PCI_VENDOR_ID_INTEL, PCI_DEVICE_ID_INTEL_FBD_CNB) }, -#if SUPPORT_I5000 { PCI_DEVICE(PCI_VENDOR_ID_INTEL, PCI_DEVICE_ID_INTEL_5000_ERR) }, -#endif { } /* Terminating entry */ }; /* Check for known platforms with I/O-AT */ static inline int i7300_idle_platform_probe(struct pci_dev **fbd_dev, - struct pci_dev **ioat_dev) + struct pci_dev **ioat_dev, + int enable_all) { int i; struct pci_dev *memdev, *dmadev; @@ -69,6 +67,8 @@ static inline int i7300_idle_platform_probe(struct pci_dev **fbd_dev, for (i = 0; fbd_ioat_list[i].vendor != 0; i++) { if (dmadev->vendor == fbd_ioat_list[i].vendor && dmadev->device == fbd_ioat_list[i].ioat_dev) { + if (!(fbd_ioat_list[i].enabled || enable_all)) + continue; if (fbd_dev) *fbd_dev = memdev; if (ioat_dev) diff --git a/include/linux/input.h b/include/linux/input.h index 0e6ff5de3588..6fed4f6a9c9e 100644 --- a/include/linux/input.h +++ b/include/linux/input.h @@ -656,6 +656,7 @@ struct input_absinfo { #define ABS_MT_POSITION_Y 0x36 /* Center Y ellipse position */ #define ABS_MT_TOOL_TYPE 0x37 /* Type of touching device */ #define ABS_MT_BLOB_ID 0x38 /* Group a set of packets as a blob */ +#define ABS_MT_TRACKING_ID 0x39 /* Unique ID of initiated contact */ #define ABS_MAX 0x3f #define ABS_CNT (ABS_MAX+1) diff --git a/include/linux/net_dropmon.h b/include/linux/net_dropmon.h index 0217fb81a630..0e2e100c44a2 100644 --- a/include/linux/net_dropmon.h +++ b/include/linux/net_dropmon.h @@ -1,6 +1,7 @@ #ifndef __NET_DROPMON_H #define __NET_DROPMON_H +#include <linux/types.h> #include <linux/netlink.h> struct net_dm_drop_point { diff --git a/include/linux/netfilter/nf_conntrack_tcp.h b/include/linux/netfilter/nf_conntrack_tcp.h index 3066789b972a..b2f384d42611 100644 --- a/include/linux/netfilter/nf_conntrack_tcp.h +++ b/include/linux/netfilter/nf_conntrack_tcp.h @@ -35,6 +35,9 @@ enum tcp_conntrack { /* Has unacknowledged data */ #define IP_CT_TCP_FLAG_DATA_UNACKNOWLEDGED 0x10 +/* The field td_maxack has been set */ +#define IP_CT_TCP_FLAG_MAXACK_SET 0x20 + struct nf_ct_tcp_flags { __u8 flags; __u8 mask; @@ -46,6 +49,7 @@ struct ip_ct_tcp_state { u_int32_t td_end; /* max of seq + len */ u_int32_t td_maxend; /* max of ack + max(win, 1) */ u_int32_t td_maxwin; /* max(win) */ + u_int32_t td_maxack; /* max of ack */ u_int8_t td_scale; /* window scale factor */ u_int8_t flags; /* per direction options */ }; diff --git a/include/linux/parport.h b/include/linux/parport.h index e1f83c5065c5..38a423ed3c01 100644 --- a/include/linux/parport.h +++ b/include/linux/parport.h @@ -324,6 +324,10 @@ struct parport { int spintime; atomic_t ref_count; + unsigned long devflags; +#define PARPORT_DEVPROC_REGISTERED 0 + struct pardevice *proc_device; /* Currently register proc device */ + struct list_head full_list; struct parport *slaves[3]; }; diff --git a/include/linux/swap.h b/include/linux/swap.h index 62d81435347a..d476aad3ff57 100644 --- a/include/linux/swap.h +++ b/include/linux/swap.h @@ -437,6 +437,11 @@ static inline int mem_cgroup_cache_charge_swapin(struct page *page, return 0; } +static inline void +mem_cgroup_uncharge_swapcache(struct page *page, swp_entry_t ent) +{ +} + #endif /* CONFIG_SWAP */ #endif /* __KERNEL__*/ #endif /* _LINUX_SWAP_H */ |