diff options
Diffstat (limited to 'include/media/v4l2-subdev.h')
| -rw-r--r-- | include/media/v4l2-subdev.h | 115 |
1 files changed, 98 insertions, 17 deletions
diff --git a/include/media/v4l2-subdev.h b/include/media/v4l2-subdev.h index 1d181b4ccb01..17856081c809 100644 --- a/include/media/v4l2-subdev.h +++ b/include/media/v4l2-subdev.h @@ -27,6 +27,16 @@ struct v4l2_device; struct v4l2_subdev; struct tuner_setup; +/* decode_vbi_line */ +struct v4l2_decode_vbi_line { + u32 is_second_field; /* Set to 0 for the first (odd) field, + set to 1 for the second (even) field. */ + u8 *p; /* Pointer to the sliced VBI data from the decoder. + On exit points to the start of the payload. */ + u32 line; /* Line number of the sliced VBI data (1-23) */ + u32 type; /* VBI service type (V4L2_SLICED_*). 0 if no service found */ +}; + /* Sub-devices are devices that are connected somehow to the main bridge device. These devices are usually audio/video muxers/encoders/decoders or sensors and webcam controllers. @@ -68,11 +78,26 @@ struct tuner_setup; the use-case it might be better to use subdev-specific ops (currently not yet implemented) since ops provide proper type-checking. */ + +/* init: initialize the sensor registors to some sort of reasonable default + values. Do not use for new drivers and should be removed in existing + drivers. + + load_fw: load firmware. + + reset: generic reset command. The argument selects which subsystems to + reset. Passing 0 will always reset the whole chip. Do not use for new + drivers without discussing this first on the linux-media mailinglist. + There should be no reason normally to reset a device. + + s_gpio: set GPIO pins. Very simple right now, might need to be extended with + a direction argument if needed. + */ struct v4l2_subdev_core_ops { int (*g_chip_ident)(struct v4l2_subdev *sd, struct v4l2_dbg_chip_ident *chip); int (*log_status)(struct v4l2_subdev *sd); int (*init)(struct v4l2_subdev *sd, u32 val); - int (*s_standby)(struct v4l2_subdev *sd, u32 standby); + int (*load_fw)(struct v4l2_subdev *sd); int (*reset)(struct v4l2_subdev *sd, u32 val); int (*s_gpio)(struct v4l2_subdev *sd, u32 val); int (*queryctrl)(struct v4l2_subdev *sd, struct v4l2_queryctrl *qc); @@ -82,6 +107,7 @@ struct v4l2_subdev_core_ops { int (*s_ext_ctrls)(struct v4l2_subdev *sd, struct v4l2_ext_controls *ctrls); int (*try_ext_ctrls)(struct v4l2_subdev *sd, struct v4l2_ext_controls *ctrls); int (*querymenu)(struct v4l2_subdev *sd, struct v4l2_querymenu *qm); + int (*s_std)(struct v4l2_subdev *sd, v4l2_std_id norm); long (*ioctl)(struct v4l2_subdev *sd, unsigned int cmd, void *arg); #ifdef CONFIG_VIDEO_ADV_DEBUG int (*g_register)(struct v4l2_subdev *sd, struct v4l2_dbg_register *reg); @@ -89,6 +115,16 @@ struct v4l2_subdev_core_ops { #endif }; +/* s_mode: switch the tuner to a specific tuner mode. Replacement of s_radio. + + s_radio: v4l device was opened in Radio mode, to be replaced by s_mode. + + s_type_addr: sets tuner type and its I2C addr. + + s_config: sets tda9887 specific stuff, like port1, port2 and qss + + s_standby: puts tuner on powersaving state, disabling it, except for i2c. + */ struct v4l2_subdev_tuner_ops { int (*s_mode)(struct v4l2_subdev *sd, enum v4l2_tuner_type); int (*s_radio)(struct v4l2_subdev *sd); @@ -96,20 +132,77 @@ struct v4l2_subdev_tuner_ops { int (*g_frequency)(struct v4l2_subdev *sd, struct v4l2_frequency *freq); int (*g_tuner)(struct v4l2_subdev *sd, struct v4l2_tuner *vt); int (*s_tuner)(struct v4l2_subdev *sd, struct v4l2_tuner *vt); - int (*s_std)(struct v4l2_subdev *sd, v4l2_std_id norm); int (*s_type_addr)(struct v4l2_subdev *sd, struct tuner_setup *type); int (*s_config)(struct v4l2_subdev *sd, const struct v4l2_priv_tun_config *config); + int (*s_standby)(struct v4l2_subdev *sd); }; +/* s_clock_freq: set the frequency (in Hz) of the audio clock output. + Used to slave an audio processor to the video decoder, ensuring that + audio and video remain synchronized. Usual values for the frequency + are 48000, 44100 or 32000 Hz. If the frequency is not supported, then + -EINVAL is returned. + + s_i2s_clock_freq: sets I2S speed in bps. This is used to provide a standard + way to select I2S clock used by driving digital audio streams at some + board designs. Usual values for the frequency are 1024000 and 2048000. + If the frequency is not supported, then -EINVAL is returned. + + s_routing: used to define the input and/or output pins of an audio chip, + and any additional configuration data. + Never attempt to use user-level input IDs (e.g. Composite, S-Video, + Tuner) at this level. An i2c device shouldn't know about whether an + input pin is connected to a Composite connector, become on another + board or platform it might be connected to something else entirely. + The calling driver is responsible for mapping a user-level input to + the right pins on the i2c device. + */ struct v4l2_subdev_audio_ops { int (*s_clock_freq)(struct v4l2_subdev *sd, u32 freq); int (*s_i2s_clock_freq)(struct v4l2_subdev *sd, u32 freq); - int (*s_routing)(struct v4l2_subdev *sd, const struct v4l2_routing *route); + int (*s_routing)(struct v4l2_subdev *sd, u32 input, u32 output, u32 config); }; +/* + decode_vbi_line: video decoders that support sliced VBI need to implement + this ioctl. Field p of the v4l2_sliced_vbi_line struct is set to the + start of the VBI data that was generated by the decoder. The driver + then parses the sliced VBI data and sets the other fields in the + struct accordingly. The pointer p is updated to point to the start of + the payload which can be copied verbatim into the data field of the + v4l2_sliced_vbi_data struct. If no valid VBI data was found, then the + type field is set to 0 on return. + + s_vbi_data: used to generate VBI signals on a video signal. + v4l2_sliced_vbi_data is filled with the data packets that should be + output. Note that if you set the line field to 0, then that VBI signal + is disabled. If no valid VBI data was found, then the type field is + set to 0 on return. + + g_vbi_data: used to obtain the sliced VBI packet from a readback register. + Not all video decoders support this. If no data is available because + the readback register contains invalid or erroneous data -EIO is + returned. Note that you must fill in the 'id' member and the 'field' + member (to determine whether CC data from the first or second field + should be obtained). + + s_std_output: set v4l2_std_id for video OUTPUT devices. This is ignored by + video input devices. + + s_crystal_freq: sets the frequency of the crystal used to generate the + clocks in Hz. An extra flags field allows device specific configuration + regarding clock frequency dividers, etc. If not used, then set flags + to 0. If the frequency is not supported, then -EINVAL is returned. + + g_input_status: get input status. Same as the status field in the v4l2_input + struct. + + s_routing: see s_routing in audio_ops, except this version is for video + devices. + */ struct v4l2_subdev_video_ops { - int (*s_routing)(struct v4l2_subdev *sd, const struct v4l2_routing *route); - int (*s_crystal_freq)(struct v4l2_subdev *sd, struct v4l2_crystal_freq *freq); + int (*s_routing)(struct v4l2_subdev *sd, u32 input, u32 output, u32 config); + int (*s_crystal_freq)(struct v4l2_subdev *sd, u32 freq, u32 flags); int (*decode_vbi_line)(struct v4l2_subdev *sd, struct v4l2_decode_vbi_line *vbi_line); int (*s_vbi_data)(struct v4l2_subdev *sd, const struct v4l2_sliced_vbi_data *vbi_data); int (*g_vbi_data)(struct v4l2_subdev *sd, struct v4l2_sliced_vbi_data *vbi_data); @@ -163,18 +256,6 @@ static inline void *v4l2_get_subdevdata(const struct v4l2_subdev *sd) return sd->priv; } -/* Convert an ioctl-type command to the proper v4l2_subdev_ops function call. - This is used by subdev modules that can be called by both old-style ioctl - commands and through the v4l2_subdev_ops. - - The ioctl API of the subdev driver can call this function to call the - right ops based on the ioctl cmd and arg. - - Once all subdev drivers have been converted and all drivers no longer - use the ioctl interface, then this function can be removed. - */ -int v4l2_subdev_command(struct v4l2_subdev *sd, unsigned cmd, void *arg); - static inline void v4l2_subdev_init(struct v4l2_subdev *sd, const struct v4l2_subdev_ops *ops) { |