diff options
Diffstat (limited to 'include/uapi/linux/ethtool.h')
| -rw-r--r-- | include/uapi/linux/ethtool.h | 1085 |
1 files changed, 1085 insertions, 0 deletions
diff --git a/include/uapi/linux/ethtool.h b/include/uapi/linux/ethtool.h new file mode 100644 index 000000000000..d3eaaaf1009e --- /dev/null +++ b/include/uapi/linux/ethtool.h @@ -0,0 +1,1085 @@ +/* + * ethtool.h: Defines for Linux ethtool. + * + * Copyright (C) 1998 David S. Miller (davem@redhat.com) + * Copyright 2001 Jeff Garzik <jgarzik@pobox.com> + * Portions Copyright 2001 Sun Microsystems (thockin@sun.com) + * Portions Copyright 2002 Intel (eli.kupermann@intel.com, + * christopher.leech@intel.com, + * scott.feldman@intel.com) + * Portions Copyright (C) Sun Microsystems 2008 + */ + +#ifndef _UAPI_LINUX_ETHTOOL_H +#define _UAPI_LINUX_ETHTOOL_H + +#include <linux/types.h> +#include <linux/if_ether.h> + +/* This should work for both 32 and 64 bit userland. */ +struct ethtool_cmd { + __u32 cmd; + __u32 supported; /* Features this interface supports */ + __u32 advertising; /* Features this interface advertises */ + __u16 speed; /* The forced speed (lower bits) in + * Mbps. Please use + * ethtool_cmd_speed()/_set() to + * access it */ + __u8 duplex; /* Duplex, half or full */ + __u8 port; /* Which connector port */ + __u8 phy_address; /* MDIO PHY address (PRTAD for clause 45). + * May be read-only or read-write + * depending on the driver. + */ + __u8 transceiver; /* Which transceiver to use */ + __u8 autoneg; /* Enable or disable autonegotiation */ + __u8 mdio_support; /* MDIO protocols supported. Read-only. + * Not set by all drivers. + */ + __u32 maxtxpkt; /* Tx pkts before generating tx int */ + __u32 maxrxpkt; /* Rx pkts before generating rx int */ + __u16 speed_hi; /* The forced speed (upper + * bits) in Mbps. Please use + * ethtool_cmd_speed()/_set() to + * access it */ + __u8 eth_tp_mdix; /* twisted pair MDI-X status */ + __u8 eth_tp_mdix_ctrl; /* twisted pair MDI-X control, when set, + * link should be renegotiated if necessary + */ + __u32 lp_advertising; /* Features the link partner advertises */ + __u32 reserved[2]; +}; + +static inline void ethtool_cmd_speed_set(struct ethtool_cmd *ep, + __u32 speed) +{ + + ep->speed = (__u16)speed; + ep->speed_hi = (__u16)(speed >> 16); +} + +static inline __u32 ethtool_cmd_speed(const struct ethtool_cmd *ep) +{ + return (ep->speed_hi << 16) | ep->speed; +} + +/* Device supports clause 22 register access to PHY or peripherals + * using the interface defined in <linux/mii.h>. This should not be + * set if there are known to be no such peripherals present or if + * the driver only emulates clause 22 registers for compatibility. + */ +#define ETH_MDIO_SUPPORTS_C22 1 + +/* Device supports clause 45 register access to PHY or peripherals + * using the interface defined in <linux/mii.h> and <linux/mdio.h>. + * This should not be set if there are known to be no such peripherals + * present. + */ +#define ETH_MDIO_SUPPORTS_C45 2 + +#define ETHTOOL_FWVERS_LEN 32 +#define ETHTOOL_BUSINFO_LEN 32 +/* these strings are set to whatever the driver author decides... */ +struct ethtool_drvinfo { + __u32 cmd; + char driver[32]; /* driver short name, "tulip", "eepro100" */ + char version[32]; /* driver version string */ + char fw_version[ETHTOOL_FWVERS_LEN]; /* firmware version string */ + char bus_info[ETHTOOL_BUSINFO_LEN]; /* Bus info for this IF. */ + /* For PCI devices, use pci_name(pci_dev). */ + char reserved1[32]; + char reserved2[12]; + /* + * Some struct members below are filled in + * using ops->get_sset_count(). Obtaining + * this info from ethtool_drvinfo is now + * deprecated; Use ETHTOOL_GSSET_INFO + * instead. + */ + __u32 n_priv_flags; /* number of flags valid in ETHTOOL_GPFLAGS */ + __u32 n_stats; /* number of u64's from ETHTOOL_GSTATS */ + __u32 testinfo_len; + __u32 eedump_len; /* Size of data from ETHTOOL_GEEPROM (bytes) */ + __u32 regdump_len; /* Size of data from ETHTOOL_GREGS (bytes) */ +}; + +#define SOPASS_MAX 6 +/* wake-on-lan settings */ +struct ethtool_wolinfo { + __u32 cmd; + __u32 supported; + __u32 wolopts; + __u8 sopass[SOPASS_MAX]; /* SecureOn(tm) password */ +}; + +/* for passing single values */ +struct ethtool_value { + __u32 cmd; + __u32 data; +}; + +/* for passing big chunks of data */ +struct ethtool_regs { + __u32 cmd; + __u32 version; /* driver-specific, indicates different chips/revs */ + __u32 len; /* bytes */ + __u8 data[0]; +}; + +/* for passing EEPROM chunks */ +struct ethtool_eeprom { + __u32 cmd; + __u32 magic; + __u32 offset; /* in bytes */ + __u32 len; /* in bytes */ + __u8 data[0]; +}; + +/** + * struct ethtool_eee - Energy Efficient Ethernet information + * @cmd: ETHTOOL_{G,S}EEE + * @supported: Mask of %SUPPORTED_* flags for the speed/duplex combinations + * for which there is EEE support. + * @advertised: Mask of %ADVERTISED_* flags for the speed/duplex combinations + * advertised as eee capable. + * @lp_advertised: Mask of %ADVERTISED_* flags for the speed/duplex + * combinations advertised by the link partner as eee capable. + * @eee_active: Result of the eee auto negotiation. + * @eee_enabled: EEE configured mode (enabled/disabled). + * @tx_lpi_enabled: Whether the interface should assert its tx lpi, given + * that eee was negotiated. + * @tx_lpi_timer: Time in microseconds the interface delays prior to asserting + * its tx lpi (after reaching 'idle' state). Effective only when eee + * was negotiated and tx_lpi_enabled was set. + */ +struct ethtool_eee { + __u32 cmd; + __u32 supported; + __u32 advertised; + __u32 lp_advertised; + __u32 eee_active; + __u32 eee_enabled; + __u32 tx_lpi_enabled; + __u32 tx_lpi_timer; + __u32 reserved[2]; +}; + +/** + * struct ethtool_modinfo - plugin module eeprom information + * @cmd: %ETHTOOL_GMODULEINFO + * @type: Standard the module information conforms to %ETH_MODULE_SFF_xxxx + * @eeprom_len: Length of the eeprom + * + * This structure is used to return the information to + * properly size memory for a subsequent call to %ETHTOOL_GMODULEEEPROM. + * The type code indicates the eeprom data format + */ +struct ethtool_modinfo { + __u32 cmd; + __u32 type; + __u32 eeprom_len; + __u32 reserved[8]; +}; + +/** + * struct ethtool_coalesce - coalescing parameters for IRQs and stats updates + * @cmd: ETHTOOL_{G,S}COALESCE + * @rx_coalesce_usecs: How many usecs to delay an RX interrupt after + * a packet arrives. + * @rx_max_coalesced_frames: Maximum number of packets to receive + * before an RX interrupt. + * @rx_coalesce_usecs_irq: Same as @rx_coalesce_usecs, except that + * this value applies while an IRQ is being serviced by the host. + * @rx_max_coalesced_frames_irq: Same as @rx_max_coalesced_frames, + * except that this value applies while an IRQ is being serviced + * by the host. + * @tx_coalesce_usecs: How many usecs to delay a TX interrupt after + * a packet is sent. + * @tx_max_coalesced_frames: Maximum number of packets to be sent + * before a TX interrupt. + * @tx_coalesce_usecs_irq: Same as @tx_coalesce_usecs, except that + * this value applies while an IRQ is being serviced by the host. + * @tx_max_coalesced_frames_irq: Same as @tx_max_coalesced_frames, + * except that this value applies while an IRQ is being serviced + * by the host. + * @stats_block_coalesce_usecs: How many usecs to delay in-memory + * statistics block updates. Some drivers do not have an + * in-memory statistic block, and in such cases this value is + * ignored. This value must not be zero. + * @use_adaptive_rx_coalesce: Enable adaptive RX coalescing. + * @use_adaptive_tx_coalesce: Enable adaptive TX coalescing. + * @pkt_rate_low: Threshold for low packet rate (packets per second). + * @rx_coalesce_usecs_low: How many usecs to delay an RX interrupt after + * a packet arrives, when the packet rate is below @pkt_rate_low. + * @rx_max_coalesced_frames_low: Maximum number of packets to be received + * before an RX interrupt, when the packet rate is below @pkt_rate_low. + * @tx_coalesce_usecs_low: How many usecs to delay a TX interrupt after + * a packet is sent, when the packet rate is below @pkt_rate_low. + * @tx_max_coalesced_frames_low: Maximum nuumber of packets to be sent before + * a TX interrupt, when the packet rate is below @pkt_rate_low. + * @pkt_rate_high: Threshold for high packet rate (packets per second). + * @rx_coalesce_usecs_high: How many usecs to delay an RX interrupt after + * a packet arrives, when the packet rate is above @pkt_rate_high. + * @rx_max_coalesced_frames_high: Maximum number of packets to be received + * before an RX interrupt, when the packet rate is above @pkt_rate_high. + * @tx_coalesce_usecs_high: How many usecs to delay a TX interrupt after + * a packet is sent, when the packet rate is above @pkt_rate_high. + * @tx_max_coalesced_frames_high: Maximum number of packets to be sent before + * a TX interrupt, when the packet rate is above @pkt_rate_high. + * @rate_sample_interval: How often to do adaptive coalescing packet rate + * sampling, measured in seconds. Must not be zero. + * + * Each pair of (usecs, max_frames) fields specifies this exit + * condition for interrupt coalescing: + * (usecs > 0 && time_since_first_completion >= usecs) || + * (max_frames > 0 && completed_frames >= max_frames) + * It is illegal to set both usecs and max_frames to zero as this + * would cause interrupts to never be generated. To disable + * coalescing, set usecs = 0 and max_frames = 1. + * + * Some implementations ignore the value of max_frames and use the + * condition: + * time_since_first_completion >= usecs + * This is deprecated. Drivers for hardware that does not support + * counting completions should validate that max_frames == !rx_usecs. + * + * Adaptive RX/TX coalescing is an algorithm implemented by some + * drivers to improve latency under low packet rates and improve + * throughput under high packet rates. Some drivers only implement + * one of RX or TX adaptive coalescing. Anything not implemented by + * the driver causes these values to be silently ignored. + * + * When the packet rate is below @pkt_rate_high but above + * @pkt_rate_low (both measured in packets per second) the + * normal {rx,tx}_* coalescing parameters are used. + */ +struct ethtool_coalesce { + __u32 cmd; + __u32 rx_coalesce_usecs; + __u32 rx_max_coalesced_frames; + __u32 rx_coalesce_usecs_irq; + __u32 rx_max_coalesced_frames_irq; + __u32 tx_coalesce_usecs; + __u32 tx_max_coalesced_frames; + __u32 tx_coalesce_usecs_irq; + __u32 tx_max_coalesced_frames_irq; + __u32 stats_block_coalesce_usecs; + __u32 use_adaptive_rx_coalesce; + __u32 use_adaptive_tx_coalesce; + __u32 pkt_rate_low; + __u32 rx_coalesce_usecs_low; + __u32 rx_max_coalesced_frames_low; + __u32 tx_coalesce_usecs_low; + __u32 tx_max_coalesced_frames_low; + __u32 pkt_rate_high; + __u32 rx_coalesce_usecs_high; + __u32 rx_max_coalesced_frames_high; + __u32 tx_coalesce_usecs_high; + __u32 tx_max_coalesced_frames_high; + __u32 rate_sample_interval; +}; + +/* for configuring RX/TX ring parameters */ +struct ethtool_ringparam { + __u32 cmd; /* ETHTOOL_{G,S}RINGPARAM */ + + /* Read only attributes. These indicate the maximum number + * of pending RX/TX ring entries the driver will allow the + * user to set. + */ + __u32 rx_max_pending; + __u32 rx_mini_max_pending; + __u32 rx_jumbo_max_pending; + __u32 tx_max_pending; + + /* Values changeable by the user. The valid values are + * in the range 1 to the "*_max_pending" counterpart above. + */ + __u32 rx_pending; + __u32 rx_mini_pending; + __u32 rx_jumbo_pending; + __u32 tx_pending; +}; + +/** + * struct ethtool_channels - configuring number of network channel + * @cmd: ETHTOOL_{G,S}CHANNELS + * @max_rx: Read only. Maximum number of receive channel the driver support. + * @max_tx: Read only. Maximum number of transmit channel the driver support. + * @max_other: Read only. Maximum number of other channel the driver support. + * @max_combined: Read only. Maximum number of combined channel the driver + * support. Set of queues RX, TX or other. + * @rx_count: Valid values are in the range 1 to the max_rx. + * @tx_count: Valid values are in the range 1 to the max_tx. + * @other_count: Valid values are in the range 1 to the max_other. + * @combined_count: Valid values are in the range 1 to the max_combined. + * + * This can be used to configure RX, TX and other channels. + */ + +struct ethtool_channels { + __u32 cmd; + __u32 max_rx; + __u32 max_tx; + __u32 max_other; + __u32 max_combined; + __u32 rx_count; + __u32 tx_count; + __u32 other_count; + __u32 combined_count; +}; + +/* for configuring link flow control parameters */ +struct ethtool_pauseparam { + __u32 cmd; /* ETHTOOL_{G,S}PAUSEPARAM */ + + /* If the link is being auto-negotiated (via ethtool_cmd.autoneg + * being true) the user may set 'autoneg' here non-zero to have the + * pause parameters be auto-negotiated too. In such a case, the + * {rx,tx}_pause values below determine what capabilities are + * advertised. + * + * If 'autoneg' is zero or the link is not being auto-negotiated, + * then {rx,tx}_pause force the driver to use/not-use pause + * flow control. + */ + __u32 autoneg; + __u32 rx_pause; + __u32 tx_pause; +}; + +#define ETH_GSTRING_LEN 32 +enum ethtool_stringset { + ETH_SS_TEST = 0, + ETH_SS_STATS, + ETH_SS_PRIV_FLAGS, + ETH_SS_NTUPLE_FILTERS, /* Do not use, GRXNTUPLE is now deprecated */ + ETH_SS_FEATURES, +}; + +/* for passing string sets for data tagging */ +struct ethtool_gstrings { + __u32 cmd; /* ETHTOOL_GSTRINGS */ + __u32 string_set; /* string set id e.c. ETH_SS_TEST, etc*/ + __u32 len; /* number of strings in the string set */ + __u8 data[0]; +}; + +struct ethtool_sset_info { + __u32 cmd; /* ETHTOOL_GSSET_INFO */ + __u32 reserved; + __u64 sset_mask; /* input: each bit selects an sset to query */ + /* output: each bit a returned sset */ + __u32 data[0]; /* ETH_SS_xxx count, in order, based on bits + in sset_mask. One bit implies one + __u32, two bits implies two + __u32's, etc. */ +}; + +/** + * enum ethtool_test_flags - flags definition of ethtool_test + * @ETH_TEST_FL_OFFLINE: if set perform online and offline tests, otherwise + * only online tests. + * @ETH_TEST_FL_FAILED: Driver set this flag if test fails. + * @ETH_TEST_FL_EXTERNAL_LB: Application request to perform external loopback + * test. + * @ETH_TEST_FL_EXTERNAL_LB_DONE: Driver performed the external loopback test + */ + +enum ethtool_test_flags { + ETH_TEST_FL_OFFLINE = (1 << 0), + ETH_TEST_FL_FAILED = (1 << 1), + ETH_TEST_FL_EXTERNAL_LB = (1 << 2), + ETH_TEST_FL_EXTERNAL_LB_DONE = (1 << 3), +}; + +/* for requesting NIC test and getting results*/ +struct ethtool_test { + __u32 cmd; /* ETHTOOL_TEST */ + __u32 flags; /* ETH_TEST_FL_xxx */ + __u32 reserved; + __u32 len; /* result length, in number of u64 elements */ + __u64 data[0]; +}; + +/* for dumping NIC-specific statistics */ +struct ethtool_stats { + __u32 cmd; /* ETHTOOL_GSTATS */ + __u32 n_stats; /* number of u64's being returned */ + __u64 data[0]; +}; + +struct ethtool_perm_addr { + __u32 cmd; /* ETHTOOL_GPERMADDR */ + __u32 size; + __u8 data[0]; +}; + +/* boolean flags controlling per-interface behavior characteristics. + * When reading, the flag indicates whether or not a certain behavior + * is enabled/present. When writing, the flag indicates whether + * or not the driver should turn on (set) or off (clear) a behavior. + * + * Some behaviors may read-only (unconditionally absent or present). + * If such is the case, return EINVAL in the set-flags operation if the + * flag differs from the read-only value. + */ +enum ethtool_flags { + ETH_FLAG_TXVLAN = (1 << 7), /* TX VLAN offload enabled */ + ETH_FLAG_RXVLAN = (1 << 8), /* RX VLAN offload enabled */ + ETH_FLAG_LRO = (1 << 15), /* LRO is enabled */ + ETH_FLAG_NTUPLE = (1 << 27), /* N-tuple filters enabled */ + ETH_FLAG_RXHASH = (1 << 28), +}; + +/* The following structures are for supporting RX network flow + * classification and RX n-tuple configuration. Note, all multibyte + * fields, e.g., ip4src, ip4dst, psrc, pdst, spi, etc. are expected to + * be in network byte order. + */ + +/** + * struct ethtool_tcpip4_spec - flow specification for TCP/IPv4 etc. + * @ip4src: Source host + * @ip4dst: Destination host + * @psrc: Source port + * @pdst: Destination port + * @tos: Type-of-service + * + * This can be used to specify a TCP/IPv4, UDP/IPv4 or SCTP/IPv4 flow. + */ +struct ethtool_tcpip4_spec { + __be32 ip4src; + __be32 ip4dst; + __be16 psrc; + __be16 pdst; + __u8 tos; +}; + +/** + * struct ethtool_ah_espip4_spec - flow specification for IPsec/IPv4 + * @ip4src: Source host + * @ip4dst: Destination host + * @spi: Security parameters index + * @tos: Type-of-service + * + * This can be used to specify an IPsec transport or tunnel over IPv4. + */ +struct ethtool_ah_espip4_spec { + __be32 ip4src; + __be32 ip4dst; + __be32 spi; + __u8 tos; +}; + +#define ETH_RX_NFC_IP4 1 + +/** + * struct ethtool_usrip4_spec - general flow specification for IPv4 + * @ip4src: Source host + * @ip4dst: Destination host + * @l4_4_bytes: First 4 bytes of transport (layer 4) header + * @tos: Type-of-service + * @ip_ver: Value must be %ETH_RX_NFC_IP4; mask must be 0 + * @proto: Transport protocol number; mask must be 0 + */ +struct ethtool_usrip4_spec { + __be32 ip4src; + __be32 ip4dst; + __be32 l4_4_bytes; + __u8 tos; + __u8 ip_ver; + __u8 proto; +}; + +union ethtool_flow_union { + struct ethtool_tcpip4_spec tcp_ip4_spec; + struct ethtool_tcpip4_spec udp_ip4_spec; + struct ethtool_tcpip4_spec sctp_ip4_spec; + struct ethtool_ah_espip4_spec ah_ip4_spec; + struct ethtool_ah_espip4_spec esp_ip4_spec; + struct ethtool_usrip4_spec usr_ip4_spec; + struct ethhdr ether_spec; + __u8 hdata[60]; +}; + +struct ethtool_flow_ext { + __be16 vlan_etype; + __be16 vlan_tci; + __be32 data[2]; +}; + +/** + * struct ethtool_rx_flow_spec - classification rule for RX flows + * @flow_type: Type of match to perform, e.g. %TCP_V4_FLOW + * @h_u: Flow fields to match (dependent on @flow_type) + * @h_ext: Additional fields to match + * @m_u: Masks for flow field bits to be matched + * @m_ext: Masks for additional field bits to be matched + * Note, all additional fields must be ignored unless @flow_type + * includes the %FLOW_EXT flag. + * @ring_cookie: RX ring/queue index to deliver to, or %RX_CLS_FLOW_DISC + * if packets should be discarded + * @location: Location of rule in the table. Locations must be + * numbered such that a flow matching multiple rules will be + * classified according to the first (lowest numbered) rule. + */ +struct ethtool_rx_flow_spec { + __u32 flow_type; + union ethtool_flow_union h_u; + struct ethtool_flow_ext h_ext; + union ethtool_flow_union m_u; + struct ethtool_flow_ext m_ext; + __u64 ring_cookie; + __u32 location; +}; + +/** + * struct ethtool_rxnfc - command to get or set RX flow classification rules + * @cmd: Specific command number - %ETHTOOL_GRXFH, %ETHTOOL_SRXFH, + * %ETHTOOL_GRXRINGS, %ETHTOOL_GRXCLSRLCNT, %ETHTOOL_GRXCLSRULE, + * %ETHTOOL_GRXCLSRLALL, %ETHTOOL_SRXCLSRLDEL or %ETHTOOL_SRXCLSRLINS + * @flow_type: Type of flow to be affected, e.g. %TCP_V4_FLOW + * @data: Command-dependent value + * @fs: Flow classification rule + * @rule_cnt: Number of rules to be affected + * @rule_locs: Array of used rule locations + * + * For %ETHTOOL_GRXFH and %ETHTOOL_SRXFH, @data is a bitmask indicating + * the fields included in the flow hash, e.g. %RXH_IP_SRC. The following + * structure fields must not be used. + * + * For %ETHTOOL_GRXRINGS, @data is set to the number of RX rings/queues + * on return. + * + * For %ETHTOOL_GRXCLSRLCNT, @rule_cnt is set to the number of defined + * rules on return. If @data is non-zero on return then it is the + * size of the rule table, plus the flag %RX_CLS_LOC_SPECIAL if the + * driver supports any special location values. If that flag is not + * set in @data then special location values should not be used. + * + * For %ETHTOOL_GRXCLSRULE, @fs.@location specifies the location of an + * existing rule on entry and @fs contains the rule on return. + * + * For %ETHTOOL_GRXCLSRLALL, @rule_cnt specifies the array size of the + * user buffer for @rule_locs on entry. On return, @data is the size + * of the rule table, @rule_cnt is the number of defined rules, and + * @rule_locs contains the locations of the defined rules. Drivers + * must use the second parameter to get_rxnfc() instead of @rule_locs. + * + * For %ETHTOOL_SRXCLSRLINS, @fs specifies the rule to add or update. + * @fs.@location either specifies the location to use or is a special + * location value with %RX_CLS_LOC_SPECIAL flag set. On return, + * @fs.@location is the actual rule location. + * + * For %ETHTOOL_SRXCLSRLDEL, @fs.@location specifies the location of an + * existing rule on entry. + * + * A driver supporting the special location values for + * %ETHTOOL_SRXCLSRLINS may add the rule at any suitable unused + * location, and may remove a rule at a later location (lower + * priority) that matches exactly the same set of flows. The special + * values are: %RX_CLS_LOC_ANY, selecting any location; + * %RX_CLS_LOC_FIRST, selecting the first suitable location (maximum + * priority); and %RX_CLS_LOC_LAST, selecting the last suitable + * location (minimum priority). Additional special values may be + * defined in future and drivers must return -%EINVAL for any + * unrecognised value. + */ +struct ethtool_rxnfc { + __u32 cmd; + __u32 flow_type; + __u64 data; + struct ethtool_rx_flow_spec fs; + __u32 rule_cnt; + __u32 rule_locs[0]; +}; + + +/** + * struct ethtool_rxfh_indir - command to get or set RX flow hash indirection + * @cmd: Specific command number - %ETHTOOL_GRXFHINDIR or %ETHTOOL_SRXFHINDIR + * @size: On entry, the array size of the user buffer, which may be zero. + * On return from %ETHTOOL_GRXFHINDIR, the array size of the hardware + * indirection table. + * @ring_index: RX ring/queue index for each hash value + * + * For %ETHTOOL_GRXFHINDIR, a @size of zero means that only the size + * should be returned. For %ETHTOOL_SRXFHINDIR, a @size of zero means + * the table should be reset to default values. This last feature + * is not supported by the original implementations. + */ +struct ethtool_rxfh_indir { + __u32 cmd; + __u32 size; + __u32 ring_index[0]; +}; + +/** + * struct ethtool_rx_ntuple_flow_spec - specification for RX flow filter + * @flow_type: Type of match to perform, e.g. %TCP_V4_FLOW + * @h_u: Flow field values to match (dependent on @flow_type) + * @m_u: Masks for flow field value bits to be ignored + * @vlan_tag: VLAN tag to match + * @vlan_tag_mask: Mask for VLAN tag bits to be ignored + * @data: Driver-dependent data to match + * @data_mask: Mask for driver-dependent data bits to be ignored + * @action: RX ring/queue index to deliver to (non-negative) or other action + * (negative, e.g. %ETHTOOL_RXNTUPLE_ACTION_DROP) + * + * For flow types %TCP_V4_FLOW, %UDP_V4_FLOW and %SCTP_V4_FLOW, where + * a field value and mask are both zero this is treated as if all mask + * bits are set i.e. the field is ignored. + */ +struct ethtool_rx_ntuple_flow_spec { + __u32 flow_type; + union { + struct ethtool_tcpip4_spec tcp_ip4_spec; + struct ethtool_tcpip4_spec udp_ip4_spec; + struct ethtool_tcpip4_spec sctp_ip4_spec; + struct ethtool_ah_espip4_spec ah_ip4_spec; + struct ethtool_ah_espip4_spec esp_ip4_spec; + struct ethtool_usrip4_spec usr_ip4_spec; + struct ethhdr ether_spec; + __u8 hdata[72]; + } h_u, m_u; + + __u16 vlan_tag; + __u16 vlan_tag_mask; + __u64 data; + __u64 data_mask; + + __s32 action; +#define ETHTOOL_RXNTUPLE_ACTION_DROP (-1) /* drop packet */ +#define ETHTOOL_RXNTUPLE_ACTION_CLEAR (-2) /* clear filter */ +}; + +/** + * struct ethtool_rx_ntuple - command to set or clear RX flow filter + * @cmd: Command number - %ETHTOOL_SRXNTUPLE + * @fs: Flow filter specification + */ +struct ethtool_rx_ntuple { + __u32 cmd; + struct ethtool_rx_ntuple_flow_spec fs; +}; + +#define ETHTOOL_FLASH_MAX_FILENAME 128 +enum ethtool_flash_op_type { + ETHTOOL_FLASH_ALL_REGIONS = 0, +}; + +/* for passing firmware flashing related parameters */ +struct ethtool_flash { + __u32 cmd; + __u32 region; + char data[ETHTOOL_FLASH_MAX_FILENAME]; +}; + +/** + * struct ethtool_dump - used for retrieving, setting device dump + * @cmd: Command number - %ETHTOOL_GET_DUMP_FLAG, %ETHTOOL_GET_DUMP_DATA, or + * %ETHTOOL_SET_DUMP + * @version: FW version of the dump, filled in by driver + * @flag: driver dependent flag for dump setting, filled in by driver during + * get and filled in by ethtool for set operation. + * flag must be initialized by macro ETH_FW_DUMP_DISABLE value when + * firmware dump is disabled. + * @len: length of dump data, used as the length of the user buffer on entry to + * %ETHTOOL_GET_DUMP_DATA and this is returned as dump length by driver + * for %ETHTOOL_GET_DUMP_FLAG command + * @data: data collected for get dump data operation + */ + +#define ETH_FW_DUMP_DISABLE 0 + +struct ethtool_dump { + __u32 cmd; + __u32 version; + __u32 flag; + __u32 len; + __u8 data[0]; +}; + +/* for returning and changing feature sets */ + +/** + * struct ethtool_get_features_block - block with state of 32 features + * @available: mask of changeable features + * @requested: mask of features requested to be enabled if possible + * @active: mask of currently enabled features + * @never_changed: mask of features not changeable for any device + */ +struct ethtool_get_features_block { + __u32 available; + __u32 requested; + __u32 active; + __u32 never_changed; +}; + +/** + * struct ethtool_gfeatures - command to get state of device's features + * @cmd: command number = %ETHTOOL_GFEATURES + * @size: in: number of elements in the features[] array; + * out: number of elements in features[] needed to hold all features + * @features: state of features + */ +struct ethtool_gfeatures { + __u32 cmd; + __u32 size; + struct ethtool_get_features_block features[0]; +}; + +/** + * struct ethtool_set_features_block - block with request for 32 features + * @valid: mask of features to be changed + * @requested: values of features to be changed + */ +struct ethtool_set_features_block { + __u32 valid; + __u32 requested; +}; + +/** + * struct ethtool_sfeatures - command to request change in device's features + * @cmd: command number = %ETHTOOL_SFEATURES + * @size: array size of the features[] array + * @features: feature change masks + */ +struct ethtool_sfeatures { + __u32 cmd; + __u32 size; + struct ethtool_set_features_block features[0]; +}; + +/** + * struct ethtool_ts_info - holds a device's timestamping and PHC association + * @cmd: command number = %ETHTOOL_GET_TS_INFO + * @so_timestamping: bit mask of the sum of the supported SO_TIMESTAMPING flags + * @phc_index: device index of the associated PHC, or -1 if there is none + * @tx_types: bit mask of the supported hwtstamp_tx_types enumeration values + * @rx_filters: bit mask of the supported hwtstamp_rx_filters enumeration values + * + * The bits in the 'tx_types' and 'rx_filters' fields correspond to + * the 'hwtstamp_tx_types' and 'hwtstamp_rx_filters' enumeration values, + * respectively. For example, if the device supports HWTSTAMP_TX_ON, + * then (1 << HWTSTAMP_TX_ON) in 'tx_types' will be set. + */ +struct ethtool_ts_info { + __u32 cmd; + __u32 so_timestamping; + __s32 phc_index; + __u32 tx_types; + __u32 tx_reserved[3]; + __u32 rx_filters; + __u32 rx_reserved[3]; +}; + +/* + * %ETHTOOL_SFEATURES changes features present in features[].valid to the + * values of corresponding bits in features[].requested. Bits in .requested + * not set in .valid or not changeable are ignored. + * + * Returns %EINVAL when .valid contains undefined or never-changeable bits + * or size is not equal to required number of features words (32-bit blocks). + * Returns >= 0 if request was completed; bits set in the value mean: + * %ETHTOOL_F_UNSUPPORTED - there were bits set in .valid that are not + * changeable (not present in %ETHTOOL_GFEATURES' features[].available) + * those bits were ignored. + * %ETHTOOL_F_WISH - some or all changes requested were recorded but the + * resulting state of bits masked by .valid is not equal to .requested. + * Probably there are other device-specific constraints on some features + * in the set. When %ETHTOOL_F_UNSUPPORTED is set, .valid is considered + * here as though ignored bits were cleared. + * %ETHTOOL_F_COMPAT - some or all changes requested were made by calling + * compatibility functions. Requested offload state cannot be properly + * managed by kernel. + * + * Meaning of bits in the masks are obtained by %ETHTOOL_GSSET_INFO (number of + * bits in the arrays - always multiple of 32) and %ETHTOOL_GSTRINGS commands + * for ETH_SS_FEATURES string set. First entry in the table corresponds to least + * significant bit in features[0] fields. Empty strings mark undefined features. + */ +enum ethtool_sfeatures_retval_bits { + ETHTOOL_F_UNSUPPORTED__BIT, + ETHTOOL_F_WISH__BIT, + ETHTOOL_F_COMPAT__BIT, +}; + +#define ETHTOOL_F_UNSUPPORTED (1 << ETHTOOL_F_UNSUPPORTED__BIT) +#define ETHTOOL_F_WISH (1 << ETHTOOL_F_WISH__BIT) +#define ETHTOOL_F_COMPAT (1 << ETHTOOL_F_COMPAT__BIT) + + +/* CMDs currently supported */ +#define ETHTOOL_GSET 0x00000001 /* Get settings. */ +#define ETHTOOL_SSET 0x00000002 /* Set settings. */ +#define ETHTOOL_GDRVINFO 0x00000003 /* Get driver info. */ +#define ETHTOOL_GREGS 0x00000004 /* Get NIC registers. */ +#define ETHTOOL_GWOL 0x00000005 /* Get wake-on-lan options. */ +#define ETHTOOL_SWOL 0x00000006 /* Set wake-on-lan options. */ +#define ETHTOOL_GMSGLVL 0x00000007 /* Get driver message level */ +#define ETHTOOL_SMSGLVL 0x00000008 /* Set driver msg level. */ +#define ETHTOOL_NWAY_RST 0x00000009 /* Restart autonegotiation. */ +/* Get link status for host, i.e. whether the interface *and* the + * physical port (if there is one) are up (ethtool_value). */ +#define ETHTOOL_GLINK 0x0000000a +#define ETHTOOL_GEEPROM 0x0000000b /* Get EEPROM data */ +#define ETHTOOL_SEEPROM 0x0000000c /* Set EEPROM data. */ +#define ETHTOOL_GCOALESCE 0x0000000e /* Get coalesce config */ +#define ETHTOOL_SCOALESCE 0x0000000f /* Set coalesce config. */ +#define ETHTOOL_GRINGPARAM 0x00000010 /* Get ring parameters */ +#define ETHTOOL_SRINGPARAM 0x00000011 /* Set ring parameters. */ +#define ETHTOOL_GPAUSEPARAM 0x00000012 /* Get pause parameters */ +#define ETHTOOL_SPAUSEPARAM 0x00000013 /* Set pause parameters. */ +#define ETHTOOL_GRXCSUM 0x00000014 /* Get RX hw csum enable (ethtool_value) */ +#define ETHTOOL_SRXCSUM 0x00000015 /* Set RX hw csum enable (ethtool_value) */ +#define ETHTOOL_GTXCSUM 0x00000016 /* Get TX hw csum enable (ethtool_value) */ +#define ETHTOOL_STXCSUM 0x00000017 /* Set TX hw csum enable (ethtool_value) */ +#define ETHTOOL_GSG 0x00000018 /* Get scatter-gather enable + * (ethtool_value) */ +#define ETHTOOL_SSG 0x00000019 /* Set scatter-gather enable + * (ethtool_value). */ +#define ETHTOOL_TEST 0x0000001a /* execute NIC self-test. */ +#define ETHTOOL_GSTRINGS 0x0000001b /* get specified string set */ +#define ETHTOOL_PHYS_ID 0x0000001c /* identify the NIC */ +#define ETHTOOL_GSTATS 0x0000001d /* get NIC-specific statistics */ +#define ETHTOOL_GTSO 0x0000001e /* Get TSO enable (ethtool_value) */ +#define ETHTOOL_STSO 0x0000001f /* Set TSO enable (ethtool_value) */ +#define ETHTOOL_GPERMADDR 0x00000020 /* Get permanent hardware address */ +#define ETHTOOL_GUFO 0x00000021 /* Get UFO enable (ethtool_value) */ +#define ETHTOOL_SUFO 0x00000022 /* Set UFO enable (ethtool_value) */ +#define ETHTOOL_GGSO 0x00000023 /* Get GSO enable (ethtool_value) */ +#define ETHTOOL_SGSO 0x00000024 /* Set GSO enable (ethtool_value) */ +#define ETHTOOL_GFLAGS 0x00000025 /* Get flags bitmap(ethtool_value) */ +#define ETHTOOL_SFLAGS 0x00000026 /* Set flags bitmap(ethtool_value) */ +#define ETHTOOL_GPFLAGS 0x00000027 /* Get driver-private flags bitmap */ +#define ETHTOOL_SPFLAGS 0x00000028 /* Set driver-private flags bitmap */ + +#define ETHTOOL_GRXFH 0x00000029 /* Get RX flow hash configuration */ +#define ETHTOOL_SRXFH 0x0000002a /* Set RX flow hash configuration */ +#define ETHTOOL_GGRO 0x0000002b /* Get GRO enable (ethtool_value) */ +#define ETHTOOL_SGRO 0x0000002c /* Set GRO enable (ethtool_value) */ +#define ETHTOOL_GRXRINGS 0x0000002d /* Get RX rings available for LB */ +#define ETHTOOL_GRXCLSRLCNT 0x0000002e /* Get RX class rule count */ +#define ETHTOOL_GRXCLSRULE 0x0000002f /* Get RX classification rule */ +#define ETHTOOL_GRXCLSRLALL 0x00000030 /* Get all RX classification rule */ +#define ETHTOOL_SRXCLSRLDEL 0x00000031 /* Delete RX classification rule */ +#define ETHTOOL_SRXCLSRLINS 0x00000032 /* Insert RX classification rule */ +#define ETHTOOL_FLASHDEV 0x00000033 /* Flash firmware to device */ +#define ETHTOOL_RESET 0x00000034 /* Reset hardware */ +#define ETHTOOL_SRXNTUPLE 0x00000035 /* Add an n-tuple filter to device */ +#define ETHTOOL_GRXNTUPLE 0x00000036 /* deprecated */ +#define ETHTOOL_GSSET_INFO 0x00000037 /* Get string set info */ +#define ETHTOOL_GRXFHINDIR 0x00000038 /* Get RX flow hash indir'n table */ +#define ETHTOOL_SRXFHINDIR 0x00000039 /* Set RX flow hash indir'n table */ + +#define ETHTOOL_GFEATURES 0x0000003a /* Get device offload settings */ +#define ETHTOOL_SFEATURES 0x0000003b /* Change device offload settings */ +#define ETHTOOL_GCHANNELS 0x0000003c /* Get no of channels */ +#define ETHTOOL_SCHANNELS 0x0000003d /* Set no of channels */ +#define ETHTOOL_SET_DUMP 0x0000003e /* Set dump settings */ +#define ETHTOOL_GET_DUMP_FLAG 0x0000003f /* Get dump settings */ +#define ETHTOOL_GET_DUMP_DATA 0x00000040 /* Get dump data */ +#define ETHTOOL_GET_TS_INFO 0x00000041 /* Get time stamping and PHC info */ +#define ETHTOOL_GMODULEINFO 0x00000042 /* Get plug-in module information */ +#define ETHTOOL_GMODULEEEPROM 0x00000043 /* Get plug-in module eeprom */ +#define ETHTOOL_GEEE 0x00000044 /* Get EEE settings */ +#define ETHTOOL_SEEE 0x00000045 /* Set EEE settings */ + +/* compatibility with older code */ +#define SPARC_ETH_GSET ETHTOOL_GSET +#define SPARC_ETH_SSET ETHTOOL_SSET + +/* Indicates what features are supported by the interface. */ +#define SUPPORTED_10baseT_Half (1 << 0) +#define SUPPORTED_10baseT_Full (1 << 1) +#define SUPPORTED_100baseT_Half (1 << 2) +#define SUPPORTED_100baseT_Full (1 << 3) +#define SUPPORTED_1000baseT_Half (1 << 4) +#define SUPPORTED_1000baseT_Full (1 << 5) +#define SUPPORTED_Autoneg (1 << 6) +#define SUPPORTED_TP (1 << 7) +#define SUPPORTED_AUI (1 << 8) +#define SUPPORTED_MII (1 << 9) +#define SUPPORTED_FIBRE (1 << 10) +#define SUPPORTED_BNC (1 << 11) +#define SUPPORTED_10000baseT_Full (1 << 12) +#define SUPPORTED_Pause (1 << 13) +#define SUPPORTED_Asym_Pause (1 << 14) +#define SUPPORTED_2500baseX_Full (1 << 15) +#define SUPPORTED_Backplane (1 << 16) +#define SUPPORTED_1000baseKX_Full (1 << 17) +#define SUPPORTED_10000baseKX4_Full (1 << 18) +#define SUPPORTED_10000baseKR_Full (1 << 19) +#define SUPPORTED_10000baseR_FEC (1 << 20) +#define SUPPORTED_20000baseMLD2_Full (1 << 21) +#define SUPPORTED_20000baseKR2_Full (1 << 22) +#define SUPPORTED_40000baseKR4_Full (1 << 23) +#define SUPPORTED_40000baseCR4_Full (1 << 24) +#define SUPPORTED_40000baseSR4_Full (1 << 25) +#define SUPPORTED_40000baseLR4_Full (1 << 26) + +/* Indicates what features are advertised by the interface. */ +#define ADVERTISED_10baseT_Half (1 << 0) +#define ADVERTISED_10baseT_Full (1 << 1) +#define ADVERTISED_100baseT_Half (1 << 2) +#define ADVERTISED_100baseT_Full (1 << 3) +#define ADVERTISED_1000baseT_Half (1 << 4) +#define ADVERTISED_1000baseT_Full (1 << 5) +#define ADVERTISED_Autoneg (1 << 6) +#define ADVERTISED_TP (1 << 7) +#define ADVERTISED_AUI (1 << 8) +#define ADVERTISED_MII (1 << 9) +#define ADVERTISED_FIBRE (1 << 10) +#define ADVERTISED_BNC (1 << 11) +#define ADVERTISED_10000baseT_Full (1 << 12) +#define ADVERTISED_Pause (1 << 13) +#define ADVERTISED_Asym_Pause (1 << 14) +#define ADVERTISED_2500baseX_Full (1 << 15) +#define ADVERTISED_Backplane (1 << 16) +#define ADVERTISED_1000baseKX_Full (1 << 17) +#define ADVERTISED_10000baseKX4_Full (1 << 18) +#define ADVERTISED_10000baseKR_Full (1 << 19) +#define ADVERTISED_10000baseR_FEC (1 << 20) +#define ADVERTISED_20000baseMLD2_Full (1 << 21) +#define ADVERTISED_20000baseKR2_Full (1 << 22) +#define ADVERTISED_40000baseKR4_Full (1 << 23) +#define ADVERTISED_40000baseCR4_Full (1 << 24) +#define ADVERTISED_40000baseSR4_Full (1 << 25) +#define ADVERTISED_40000baseLR4_Full (1 << 26) + +/* The following are all involved in forcing a particular link + * mode for the device for setting things. When getting the + * devices settings, these indicate the current mode and whether + * it was forced up into this mode or autonegotiated. + */ + +/* The forced speed, 10Mb, 100Mb, gigabit, 2.5Gb, 10GbE. */ +#define SPEED_10 10 +#define SPEED_100 100 +#define SPEED_1000 1000 +#define SPEED_2500 2500 +#define SPEED_10000 10000 +#define SPEED_UNKNOWN -1 + +/* Duplex, half or full. */ +#define DUPLEX_HALF 0x00 +#define DUPLEX_FULL 0x01 +#define DUPLEX_UNKNOWN 0xff + +/* Which connector port. */ +#define PORT_TP 0x00 +#define PORT_AUI 0x01 +#define PORT_MII 0x02 +#define PORT_FIBRE 0x03 +#define PORT_BNC 0x04 +#define PORT_DA 0x05 +#define PORT_NONE 0xef +#define PORT_OTHER 0xff + +/* Which transceiver to use. */ +#define XCVR_INTERNAL 0x00 +#define XCVR_EXTERNAL 0x01 +#define XCVR_DUMMY1 0x02 +#define XCVR_DUMMY2 0x03 +#define XCVR_DUMMY3 0x04 + +/* Enable or disable autonegotiation. If this is set to enable, + * the forced link modes above are completely ignored. + */ +#define AUTONEG_DISABLE 0x00 +#define AUTONEG_ENABLE 0x01 + +/* MDI or MDI-X status/control - if MDI/MDI_X/AUTO is set then + * the driver is required to renegotiate link + */ +#define ETH_TP_MDI_INVALID 0x00 /* status: unknown; control: unsupported */ +#define ETH_TP_MDI 0x01 /* status: MDI; control: force MDI */ +#define ETH_TP_MDI_X 0x02 /* status: MDI-X; control: force MDI-X */ +#define ETH_TP_MDI_AUTO 0x03 /* control: auto-select */ + +/* Wake-On-Lan options. */ +#define WAKE_PHY (1 << 0) +#define WAKE_UCAST (1 << 1) +#define WAKE_MCAST (1 << 2) +#define WAKE_BCAST (1 << 3) +#define WAKE_ARP (1 << 4) +#define WAKE_MAGIC (1 << 5) +#define WAKE_MAGICSECURE (1 << 6) /* only meaningful if WAKE_MAGIC */ + +/* L2-L4 network traffic flow types */ +#define TCP_V4_FLOW 0x01 /* hash or spec (tcp_ip4_spec) */ +#define UDP_V4_FLOW 0x02 /* hash or spec (udp_ip4_spec) */ +#define SCTP_V4_FLOW 0x03 /* hash or spec (sctp_ip4_spec) */ +#define AH_ESP_V4_FLOW 0x04 /* hash only */ +#define TCP_V6_FLOW 0x05 /* hash only */ +#define UDP_V6_FLOW 0x06 /* hash only */ +#define SCTP_V6_FLOW 0x07 /* hash only */ +#define AH_ESP_V6_FLOW 0x08 /* hash only */ +#define AH_V4_FLOW 0x09 /* hash or spec (ah_ip4_spec) */ +#define ESP_V4_FLOW 0x0a /* hash or spec (esp_ip4_spec) */ +#define AH_V6_FLOW 0x0b /* hash only */ +#define ESP_V6_FLOW 0x0c /* hash only */ +#define IP_USER_FLOW 0x0d /* spec only (usr_ip4_spec) */ +#define IPV4_FLOW 0x10 /* hash only */ +#define IPV6_FLOW 0x11 /* hash only */ +#define ETHER_FLOW 0x12 /* spec only (ether_spec) */ +/* Flag to enable additional fields in struct ethtool_rx_flow_spec */ +#define FLOW_EXT 0x80000000 + +/* L3-L4 network traffic flow hash options */ +#define RXH_L2DA (1 << 1) +#define RXH_VLAN (1 << 2) +#define RXH_L3_PROTO (1 << 3) +#define RXH_IP_SRC (1 << 4) +#define RXH_IP_DST (1 << 5) +#define RXH_L4_B_0_1 (1 << 6) /* src port in case of TCP/UDP/SCTP */ +#define RXH_L4_B_2_3 (1 << 7) /* dst port in case of TCP/UDP/SCTP */ +#define RXH_DISCARD (1 << 31) + +#define RX_CLS_FLOW_DISC 0xffffffffffffffffULL + +/* Special RX classification rule insert location values */ +#define RX_CLS_LOC_SPECIAL 0x80000000 /* flag */ +#define RX_CLS_LOC_ANY 0xffffffff +#define RX_CLS_LOC_FIRST 0xfffffffe +#define RX_CLS_LOC_LAST 0xfffffffd + +/* EEPROM Standards for plug in modules */ +#define ETH_MODULE_SFF_8079 0x1 +#define ETH_MODULE_SFF_8079_LEN 256 +#define ETH_MODULE_SFF_8472 0x2 +#define ETH_MODULE_SFF_8472_LEN 512 + +/* Reset flags */ +/* The reset() operation must clear the flags for the components which + * were actually reset. On successful return, the flags indicate the + * components which were not reset, either because they do not exist + * in the hardware or because they cannot be reset independently. The + * driver must never reset any components that were not requested. + */ +enum ethtool_reset_flags { + /* These flags represent components dedicated to the interface + * the command is addressed to. Shift any flag left by + * ETH_RESET_SHARED_SHIFT to reset a shared component of the + * same type. + */ + ETH_RESET_MGMT = 1 << 0, /* Management processor */ + ETH_RESET_IRQ = 1 << 1, /* Interrupt requester */ + ETH_RESET_DMA = 1 << 2, /* DMA engine */ + ETH_RESET_FILTER = 1 << 3, /* Filtering/flow direction */ + ETH_RESET_OFFLOAD = 1 << 4, /* Protocol offload */ + ETH_RESET_MAC = 1 << 5, /* Media access controller */ + ETH_RESET_PHY = 1 << 6, /* Transceiver/PHY */ + ETH_RESET_RAM = 1 << 7, /* RAM shared between + * multiple components */ + + ETH_RESET_DEDICATED = 0x0000ffff, /* All components dedicated to + * this interface */ + ETH_RESET_ALL = 0xffffffff, /* All components used by this + * interface, even if shared */ +}; +#define ETH_RESET_SHARED_SHIFT 16 + +#endif /* _UAPI_LINUX_ETHTOOL_H */ |