1 files changed, 380 insertions, 0 deletions
diff --git a/net/dsa/mv88e6131.c b/net/dsa/mv88e6131.c
new file mode 100644
index 000000000000..36e01eb863a0
--- /dev/null
+++ b/net/dsa/mv88e6131.c
@@ -0,0 +1,380 @@
+/*
+ * net/dsa/mv88e6131.c - Marvell 88e6131 switch chip support
+ * Copyright (c) 2008 Marvell Semiconductor
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License as published by
+ * the Free Software Foundation; either version 2 of the License, or
+ * (at your option) any later version.
+ */
+
+#include <linux/list.h>
+#include <linux/netdevice.h>
+#include <linux/phy.h>
+#include "dsa_priv.h"
+#include "mv88e6xxx.h"
+
+static char *mv88e6131_probe(struct mii_bus *bus, int sw_addr)
+{
+	int ret;
+
+	ret = __mv88e6xxx_reg_read(bus, sw_addr, REG_PORT(0), 0x03);
+	if (ret >= 0) {
+		ret &= 0xfff0;
+		if (ret == 0x1060)
+			return "Marvell 88E6131";
+	}
+
+	return NULL;
+}
+
+static int mv88e6131_switch_reset(struct dsa_switch *ds)
+{
+	int i;
+	int ret;
+
+	/*
+	 * Set all ports to the disabled state.
+	 */
+	for (i = 0; i < 8; i++) {
+		ret = REG_READ(REG_PORT(i), 0x04);
+		REG_WRITE(REG_PORT(i), 0x04, ret & 0xfffc);
+	}
+
+	/*
+	 * Wait for transmit queues to drain.
+	 */
+	msleep(2);
+
+	/*
+	 * Reset the switch.
+	 */
+	REG_WRITE(REG_GLOBAL, 0x04, 0xc400);
+
+	/*
+	 * Wait up to one second for reset to complete.
+	 */
+	for (i = 0; i < 1000; i++) {
+		ret = REG_READ(REG_GLOBAL, 0x00);
+		if ((ret & 0xc800) == 0xc800)
+			break;
+
+		msleep(1);
+	}
+	if (i == 1000)
+		return -ETIMEDOUT;
+
+	return 0;
+}
+
+static int mv88e6131_setup_global(struct dsa_switch *ds)
+{
+	int ret;
+	int i;
+
+	/*
+	 * Enable the PHY polling unit, don't discard packets with
+	 * excessive collisions, use a weighted fair queueing scheme
+	 * to arbitrate between packet queues, set the maximum frame
+	 * size to 1632, and mask all interrupt sources.
+	 */
+	REG_WRITE(REG_GLOBAL, 0x04, 0x4400);
+
+	/*
+	 * Set the default address aging time to 5 minutes, and
+	 * enable address learn messages to be sent to all message
+	 * ports.
+	 */
+	REG_WRITE(REG_GLOBAL, 0x0a, 0x0148);
+
+	/*
+	 * Configure the priority mapping registers.
+	 */
+	ret = mv88e6xxx_config_prio(ds);
+	if (ret < 0)
+		return ret;
+
+	/*
+	 * Set the VLAN ethertype to 0x8100.
+	 */
+	REG_WRITE(REG_GLOBAL, 0x19, 0x8100);
+
+	/*
+	 * Disable ARP mirroring, and configure the cpu port as the
+	 * port to which ingress and egress monitor frames are to be
+	 * sent.
+	 */
+	REG_WRITE(REG_GLOBAL, 0x1a, (ds->cpu_port * 0x1100) | 0x00f0);
+
+	/*
+	 * Disable cascade port functionality, and set the switch's
+	 * DSA device number to zero.
+	 */
+	REG_WRITE(REG_GLOBAL, 0x1c, 0xe000);
+
+	/*
+	 * Send all frames with destination addresses matching
+	 * 01:80:c2:00:00:0x to the CPU port.
+	 */
+	REG_WRITE(REG_GLOBAL2, 0x03, 0xffff);
+
+	/*
+	 * Ignore removed tag data on doubly tagged packets, disable
+	 * flow control messages, force flow control priority to the
+	 * highest, and send all special multicast frames to the CPU
+	 * port at the higest priority.
+	 */
+	REG_WRITE(REG_GLOBAL2, 0x05, 0x00ff);
+
+	/*
+	 * Map all DSA device IDs to the CPU port.
+	 */
+	for (i = 0; i < 32; i++)
+		REG_WRITE(REG_GLOBAL2, 0x06, 0x8000 | (i << 8) | ds->cpu_port);
+
+	/*
+	 * Clear all trunk masks.
+	 */
+	for (i = 0; i < 8; i++)
+		REG_WRITE(REG_GLOBAL2, 0x07, 0x8000 | (i << 12) | 0xff);
+
+	/*
+	 * Clear all trunk mappings.
+	 */
+	for (i = 0; i < 16; i++)
+		REG_WRITE(REG_GLOBAL2, 0x08, 0x8000 | (i << 11));
+
+	/*
+	 * Force the priority of IGMP/MLD snoop frames and ARP frames
+	 * to the highest setting.
+	 */
+	REG_WRITE(REG_GLOBAL2, 0x0f, 0x00ff);
+
+	return 0;
+}
+
+static int mv88e6131_setup_port(struct dsa_switch *ds, int p)
+{
+	int addr = REG_PORT(p);
+
+	/*
+	 * MAC Forcing register: don't force link, speed, duplex
+	 * or flow control state to any particular values.
+	 */
+	REG_WRITE(addr, 0x01, 0x0003);
+
+	/*
+	 * Port Control: disable Core Tag, disable Drop-on-Lock,
+	 * transmit frames unmodified, disable Header mode,
+	 * enable IGMP/MLD snoop, disable DoubleTag, disable VLAN
+	 * tunneling, determine priority by looking at 802.1p and
+	 * IP priority fields (IP prio has precedence), and set STP
+	 * state to Forwarding.  Finally, if this is the CPU port,
+	 * additionally enable DSA tagging and forwarding of unknown
+	 * unicast addresses.
+	 */
+	REG_WRITE(addr, 0x04, (p == ds->cpu_port) ? 0x0537 : 0x0433);
+
+	/*
+	 * Port Control 1: disable trunking.  Also, if this is the
+	 * CPU port, enable learn messages to be sent to this port.
+	 */
+	REG_WRITE(addr, 0x05, (p == ds->cpu_port) ? 0x8000 : 0x0000);
+
+	/*
+	 * Port based VLAN map: give each port its own address
+	 * database, allow the CPU port to talk to each of the 'real'
+	 * ports, and allow each of the 'real' ports to only talk to
+	 * the CPU port.
+	 */
+	REG_WRITE(addr, 0x06,
+			((p & 0xf) << 12) |
+			 ((p == ds->cpu_port) ?
+				ds->valid_port_mask :
+				(1 << ds->cpu_port)));
+
+	/*
+	 * Default VLAN ID and priority: don't set a default VLAN
+	 * ID, and set the default packet priority to zero.
+	 */
+	REG_WRITE(addr, 0x07, 0x0000);
+
+	/*
+	 * Port Control 2: don't force a good FCS, don't use
+	 * VLAN-based, source address-based or destination
+	 * address-based priority overrides, don't let the switch
+	 * add or strip 802.1q tags, don't discard tagged or
+	 * untagged frames on this port, do a destination address
+	 * lookup on received packets as usual, don't send a copy
+	 * of all transmitted/received frames on this port to the
+	 * CPU, and configure the CPU port number.  Also, if this
+	 * is the CPU port, enable forwarding of unknown multicast
+	 * addresses.
+	 */
+	REG_WRITE(addr, 0x08,
+			((p == ds->cpu_port) ? 0x00c0 : 0x0080) |
+			 ds->cpu_port);
+
+	/*
+	 * Rate Control: disable ingress rate limiting.
+	 */
+	REG_WRITE(addr, 0x09, 0x0000);
+
+	/*
+	 * Rate Control 2: disable egress rate limiting.
+	 */
+	REG_WRITE(addr, 0x0a, 0x0000);
+
+	/*
+	 * Port Association Vector: when learning source addresses
+	 * of packets, add the address to the address database using
+	 * a port bitmap that has only the bit for this port set and
+	 * the other bits clear.
+	 */
+	REG_WRITE(addr, 0x0b, 1 << p);
+
+	/*
+	 * Tag Remap: use an identity 802.1p prio -> switch prio
+	 * mapping.
+	 */
+	REG_WRITE(addr, 0x18, 0x3210);
+
+	/*
+	 * Tag Remap 2: use an identity 802.1p prio -> switch prio
+	 * mapping.
+	 */
+	REG_WRITE(addr, 0x19, 0x7654);
+
+	return 0;
+}
+
+static int mv88e6131_setup(struct dsa_switch *ds)
+{
+	struct mv88e6xxx_priv_state *ps = (void *)(ds + 1);
+	int i;
+	int ret;
+
+	mutex_init(&ps->smi_mutex);
+	mv88e6xxx_ppu_state_init(ds);
+	mutex_init(&ps->stats_mutex);
+
+	ret = mv88e6131_switch_reset(ds);
+	if (ret < 0)
+		return ret;
+
+	/* @@@ initialise vtu and atu */
+
+	ret = mv88e6131_setup_global(ds);
+	if (ret < 0)
+		return ret;
+
+	for (i = 0; i < 6; i++) {
+		ret = mv88e6131_setup_port(ds, i);
+		if (ret < 0)
+			return ret;
+	}
+
+	return 0;
+}
+
+static int mv88e6131_port_to_phy_addr(int port)
+{
+	if (port >= 0 && port != 3 && port <= 7)
+		return port;
+	return -1;
+}
+
+static int
+mv88e6131_phy_read(struct dsa_switch *ds, int port, int regnum)
+{
+	int addr = mv88e6131_port_to_phy_addr(port);
+	return mv88e6xxx_phy_read_ppu(ds, addr, regnum);
+}
+
+static int
+mv88e6131_phy_write(struct dsa_switch *ds,
+			      int port, int regnum, u16 val)
+{
+	int addr = mv88e6131_port_to_phy_addr(port);
+	return mv88e6xxx_phy_write_ppu(ds, addr, regnum, val);
+}
+
+static struct mv88e6xxx_hw_stat mv88e6131_hw_stats[] = {
+	{ "in_good_octets", 8, 0x00, },
+	{ "in_bad_octets", 4, 0x02, },
+	{ "in_unicast", 4, 0x04, },
+	{ "in_broadcasts", 4, 0x06, },
+	{ "in_multicasts", 4, 0x07, },
+	{ "in_pause", 4, 0x16, },
+	{ "in_undersize", 4, 0x18, },
+	{ "in_fragments", 4, 0x19, },
+	{ "in_oversize", 4, 0x1a, },
+	{ "in_jabber", 4, 0x1b, },
+	{ "in_rx_error", 4, 0x1c, },
+	{ "in_fcs_error", 4, 0x1d, },
+	{ "out_octets", 8, 0x0e, },
+	{ "out_unicast", 4, 0x10, },
+	{ "out_broadcasts", 4, 0x13, },
+	{ "out_multicasts", 4, 0x12, },
+	{ "out_pause", 4, 0x15, },
+	{ "excessive", 4, 0x11, },
+	{ "collisions", 4, 0x1e, },
+	{ "deferred", 4, 0x05, },
+	{ "single", 4, 0x14, },
+	{ "multiple", 4, 0x17, },
+	{ "out_fcs_error", 4, 0x03, },
+	{ "late", 4, 0x1f, },
+	{ "hist_64bytes", 4, 0x08, },
+	{ "hist_65_127bytes", 4, 0x09, },
+	{ "hist_128_255bytes", 4, 0x0a, },
+	{ "hist_256_511bytes", 4, 0x0b, },
+	{ "hist_512_1023bytes", 4, 0x0c, },
+	{ "hist_1024_max_bytes", 4, 0x0d, },
+};
+
+static void
+mv88e6131_get_strings(struct dsa_switch *ds, int port, uint8_t *data)
+{
+	mv88e6xxx_get_strings(ds, ARRAY_SIZE(mv88e6131_hw_stats),
+			      mv88e6131_hw_stats, port, data);
+}
+
+static void
+mv88e6131_get_ethtool_stats(struct dsa_switch *ds,
+				  int port, uint64_t *data)
+{
+	mv88e6xxx_get_ethtool_stats(ds, ARRAY_SIZE(mv88e6131_hw_stats),
+				    mv88e6131_hw_stats, port, data);
+}
+
+static int mv88e6131_get_sset_count(struct dsa_switch *ds)
+{
+	return ARRAY_SIZE(mv88e6131_hw_stats);
+}
+
+static struct dsa_switch_driver mv88e6131_switch_driver = {
+	.tag_protocol		= __constant_htons(ETH_P_DSA),
+	.priv_size		= sizeof(struct mv88e6xxx_priv_state),
+	.probe			= mv88e6131_probe,
+	.setup			= mv88e6131_setup,
+	.set_addr		= mv88e6xxx_set_addr_direct,
+	.phy_read		= mv88e6131_phy_read,
+	.phy_write		= mv88e6131_phy_write,
+	.poll_link		= mv88e6xxx_poll_link,
+	.get_strings		= mv88e6131_get_strings,
+	.get_ethtool_stats	= mv88e6131_get_ethtool_stats,
+	.get_sset_count		= mv88e6131_get_sset_count,
+};
+
+int __init mv88e6131_init(void)
+{
+	register_switch_driver(&mv88e6131_switch_driver);
+	return 0;
+}
+module_init(mv88e6131_init);
+
+void __exit mv88e6131_cleanup(void)
+{
+	unregister_switch_driver(&mv88e6131_switch_driver);
+}
+module_exit(mv88e6131_cleanup);