diff options
Diffstat (limited to 'sound/soc/fsl/fsl_ssi.c')
| -rw-r--r-- | sound/soc/fsl/fsl_ssi.c | 500 |
1 files changed, 373 insertions, 127 deletions
diff --git a/sound/soc/fsl/fsl_ssi.c b/sound/soc/fsl/fsl_ssi.c index 2f2d837df07f..5cf626c4dc96 100644 --- a/sound/soc/fsl/fsl_ssi.c +++ b/sound/soc/fsl/fsl_ssi.c @@ -8,6 +8,26 @@ * This file is licensed under the terms of the GNU General Public License * version 2. This program is licensed "as is" without any warranty of any * kind, whether express or implied. + * + * + * Some notes why imx-pcm-fiq is used instead of DMA on some boards: + * + * The i.MX SSI core has some nasty limitations in AC97 mode. While most + * sane processor vendors have a FIFO per AC97 slot, the i.MX has only + * one FIFO which combines all valid receive slots. We cannot even select + * which slots we want to receive. The WM9712 with which this driver + * was developed with always sends GPIO status data in slot 12 which + * we receive in our (PCM-) data stream. The only chance we have is to + * manually skip this data in the FIQ handler. With sampling rates different + * from 48000Hz not every frame has valid receive data, so the ratio + * between pcm data and GPIO status data changes. Our FIQ handler is not + * able to handle this, hence this driver only works with 48000Hz sampling + * rate. + * Reading and writing AC97 registers is another challenge. The core + * provides us status bits when the read register is updated with *another* + * value. When we read the same register two times (and the register still + * contains the same value) these status bits are not set. We work + * around this by not polling these bits but only wait a fixed delay. */ #include <linux/init.h> @@ -36,7 +56,7 @@ #define read_ssi(addr) in_be32(addr) #define write_ssi(val, addr) out_be32(addr, val) #define write_ssi_mask(addr, clear, set) clrsetbits_be32(addr, clear, set) -#elif defined ARM +#else #define read_ssi(addr) readl(addr) #define write_ssi(val, addr) writel(val, addr) /* @@ -121,11 +141,14 @@ struct fsl_ssi_private { bool new_binding; bool ssi_on_imx; + bool imx_ac97; + bool use_dma; struct clk *clk; struct snd_dmaengine_dai_dma_data dma_params_tx; struct snd_dmaengine_dai_dma_data dma_params_rx; struct imx_dma_data filter_data_tx; struct imx_dma_data filter_data_rx; + struct imx_pcm_fiq_params fiq_params; struct { unsigned int rfrc; @@ -298,6 +321,102 @@ static irqreturn_t fsl_ssi_isr(int irq, void *dev_id) return ret; } +static int fsl_ssi_setup(struct fsl_ssi_private *ssi_private) +{ + struct ccsr_ssi __iomem *ssi = ssi_private->ssi; + u8 i2s_mode; + u8 wm; + int synchronous = ssi_private->cpu_dai_drv.symmetric_rates; + + if (ssi_private->imx_ac97) + i2s_mode = CCSR_SSI_SCR_I2S_MODE_NORMAL | CCSR_SSI_SCR_NET; + else + i2s_mode = CCSR_SSI_SCR_I2S_MODE_SLAVE; + + /* + * Section 16.5 of the MPC8610 reference manual says that the SSI needs + * to be disabled before updating the registers we set here. + */ + write_ssi_mask(&ssi->scr, CCSR_SSI_SCR_SSIEN, 0); + + /* + * Program the SSI into I2S Slave Non-Network Synchronous mode. Also + * enable the transmit and receive FIFO. + * + * FIXME: Little-endian samples require a different shift dir + */ + write_ssi_mask(&ssi->scr, + CCSR_SSI_SCR_I2S_MODE_MASK | CCSR_SSI_SCR_SYN, + CCSR_SSI_SCR_TFR_CLK_DIS | + i2s_mode | + (synchronous ? CCSR_SSI_SCR_SYN : 0)); + + write_ssi(CCSR_SSI_STCR_TXBIT0 | CCSR_SSI_STCR_TFEN0 | + CCSR_SSI_STCR_TFSI | CCSR_SSI_STCR_TEFS | + CCSR_SSI_STCR_TSCKP, &ssi->stcr); + + write_ssi(CCSR_SSI_SRCR_RXBIT0 | CCSR_SSI_SRCR_RFEN0 | + CCSR_SSI_SRCR_RFSI | CCSR_SSI_SRCR_REFS | + CCSR_SSI_SRCR_RSCKP, &ssi->srcr); + /* + * The DC and PM bits are only used if the SSI is the clock master. + */ + + /* + * Set the watermark for transmit FIFI 0 and receive FIFO 0. We don't + * use FIFO 1. We program the transmit water to signal a DMA transfer + * if there are only two (or fewer) elements left in the FIFO. Two + * elements equals one frame (left channel, right channel). This value, + * however, depends on the depth of the transmit buffer. + * + * We set the watermark on the same level as the DMA burstsize. For + * fiq it is probably better to use the biggest possible watermark + * size. + */ + if (ssi_private->use_dma) + wm = ssi_private->fifo_depth - 2; + else + wm = ssi_private->fifo_depth; + + write_ssi(CCSR_SSI_SFCSR_TFWM0(wm) | CCSR_SSI_SFCSR_RFWM0(wm) | + CCSR_SSI_SFCSR_TFWM1(wm) | CCSR_SSI_SFCSR_RFWM1(wm), + &ssi->sfcsr); + + /* + * For ac97 interrupts are enabled with the startup of the substream + * because it is also running without an active substream. Normally SSI + * is only enabled when there is a substream. + */ + if (ssi_private->imx_ac97) { + /* + * Setup the clock control register + */ + write_ssi(CCSR_SSI_SxCCR_WL(17) | CCSR_SSI_SxCCR_DC(13), + &ssi->stccr); + write_ssi(CCSR_SSI_SxCCR_WL(17) | CCSR_SSI_SxCCR_DC(13), + &ssi->srccr); + + /* + * Enable AC97 mode and startup the SSI + */ + write_ssi(CCSR_SSI_SACNT_AC97EN | CCSR_SSI_SACNT_FV, + &ssi->sacnt); + write_ssi(0xff, &ssi->saccdis); + write_ssi(0x300, &ssi->saccen); + + /* + * Enable SSI, Transmit and Receive + */ + write_ssi_mask(&ssi->scr, 0, CCSR_SSI_SCR_SSIEN | + CCSR_SSI_SCR_TE | CCSR_SSI_SCR_RE); + + write_ssi(CCSR_SSI_SOR_WAIT(3), &ssi->sor); + } + + return 0; +} + + /** * fsl_ssi_startup: create a new substream * @@ -319,70 +438,14 @@ static int fsl_ssi_startup(struct snd_pcm_substream *substream, * and initialize the SSI registers. */ if (!ssi_private->first_stream) { - struct ccsr_ssi __iomem *ssi = ssi_private->ssi; - ssi_private->first_stream = substream; /* - * Section 16.5 of the MPC8610 reference manual says that the - * SSI needs to be disabled before updating the registers we set - * here. - */ - write_ssi_mask(&ssi->scr, CCSR_SSI_SCR_SSIEN, 0); - - /* - * Program the SSI into I2S Slave Non-Network Synchronous mode. - * Also enable the transmit and receive FIFO. - * - * FIXME: Little-endian samples require a different shift dir - */ - write_ssi_mask(&ssi->scr, - CCSR_SSI_SCR_I2S_MODE_MASK | CCSR_SSI_SCR_SYN, - CCSR_SSI_SCR_TFR_CLK_DIS | CCSR_SSI_SCR_I2S_MODE_SLAVE - | (synchronous ? CCSR_SSI_SCR_SYN : 0)); - - write_ssi(CCSR_SSI_STCR_TXBIT0 | CCSR_SSI_STCR_TFEN0 | - CCSR_SSI_STCR_TFSI | CCSR_SSI_STCR_TEFS | - CCSR_SSI_STCR_TSCKP, &ssi->stcr); - - write_ssi(CCSR_SSI_SRCR_RXBIT0 | CCSR_SSI_SRCR_RFEN0 | - CCSR_SSI_SRCR_RFSI | CCSR_SSI_SRCR_REFS | - CCSR_SSI_SRCR_RSCKP, &ssi->srcr); - - /* - * The DC and PM bits are only used if the SSI is the clock - * master. - */ - - /* Enable the interrupts and DMA requests */ - write_ssi(SIER_FLAGS, &ssi->sier); - - /* - * Set the watermark for transmit FIFI 0 and receive FIFO 0. We - * don't use FIFO 1. We program the transmit water to signal a - * DMA transfer if there are only two (or fewer) elements left - * in the FIFO. Two elements equals one frame (left channel, - * right channel). This value, however, depends on the depth of - * the transmit buffer. - * - * We program the receive FIFO to notify us if at least two - * elements (one frame) have been written to the FIFO. We could - * make this value larger (and maybe we should), but this way - * data will be written to memory as soon as it's available. - */ - write_ssi(CCSR_SSI_SFCSR_TFWM0(ssi_private->fifo_depth - 2) | - CCSR_SSI_SFCSR_RFWM0(ssi_private->fifo_depth - 2), - &ssi->sfcsr); - - /* - * We keep the SSI disabled because if we enable it, then the - * DMA controller will start. It's not supposed to start until - * the SCR.TE (or SCR.RE) bit is set, but it does anyway. The - * DMA controller will transfer one "BWC" of data (i.e. the - * amount of data that the MR.BWC bits are set to). The reason - * this is bad is because at this point, the PCM driver has not - * finished initializing the DMA controller. + * fsl_ssi_setup was already called by ac97_init earlier if + * the driver is in ac97 mode. */ + if (!ssi_private->imx_ac97) + fsl_ssi_setup(ssi_private); } else { if (synchronous) { struct snd_pcm_runtime *first_runtime = @@ -492,6 +555,27 @@ static int fsl_ssi_trigger(struct snd_pcm_substream *substream, int cmd, struct snd_soc_pcm_runtime *rtd = substream->private_data; struct fsl_ssi_private *ssi_private = snd_soc_dai_get_drvdata(rtd->cpu_dai); struct ccsr_ssi __iomem *ssi = ssi_private->ssi; + unsigned int sier_bits; + + /* + * Enable only the interrupts and DMA requests + * that are needed for the channel. As the fiq + * is polling for this bits, we have to ensure + * that this are aligned with the preallocated + * buffers + */ + + if (substream->stream == SNDRV_PCM_STREAM_PLAYBACK) { + if (ssi_private->use_dma) + sier_bits = SIER_FLAGS; + else + sier_bits = CCSR_SSI_SIER_TIE | CCSR_SSI_SIER_TFE0_EN; + } else { + if (ssi_private->use_dma) + sier_bits = SIER_FLAGS; + else + sier_bits = CCSR_SSI_SIER_RIE | CCSR_SSI_SIER_RFF0_EN; + } switch (cmd) { case SNDRV_PCM_TRIGGER_START: @@ -510,12 +594,18 @@ static int fsl_ssi_trigger(struct snd_pcm_substream *substream, int cmd, write_ssi_mask(&ssi->scr, CCSR_SSI_SCR_TE, 0); else write_ssi_mask(&ssi->scr, CCSR_SSI_SCR_RE, 0); + + if (!ssi_private->imx_ac97 && (read_ssi(&ssi->scr) & + (CCSR_SSI_SCR_TE | CCSR_SSI_SCR_RE)) == 0) + write_ssi_mask(&ssi->scr, CCSR_SSI_SCR_SSIEN, 0); break; default: return -EINVAL; } + write_ssi(sier_bits, &ssi->sier); + return 0; } @@ -534,22 +624,13 @@ static void fsl_ssi_shutdown(struct snd_pcm_substream *substream, ssi_private->first_stream = ssi_private->second_stream; ssi_private->second_stream = NULL; - - /* - * If this is the last active substream, disable the SSI. - */ - if (!ssi_private->first_stream) { - struct ccsr_ssi __iomem *ssi = ssi_private->ssi; - - write_ssi_mask(&ssi->scr, CCSR_SSI_SCR_SSIEN, 0); - } } static int fsl_ssi_dai_probe(struct snd_soc_dai *dai) { struct fsl_ssi_private *ssi_private = snd_soc_dai_get_drvdata(dai); - if (ssi_private->ssi_on_imx) { + if (ssi_private->ssi_on_imx && ssi_private->use_dma) { dai->playback_dma_data = &ssi_private->dma_params_tx; dai->capture_dma_data = &ssi_private->dma_params_rx; } @@ -587,6 +668,133 @@ static const struct snd_soc_component_driver fsl_ssi_component = { .name = "fsl-ssi", }; +/** + * fsl_ssi_ac97_trigger: start and stop the AC97 receive/transmit. + * + * This function is called by ALSA to start, stop, pause, and resume the + * transfer of data. + */ +static int fsl_ssi_ac97_trigger(struct snd_pcm_substream *substream, int cmd, + struct snd_soc_dai *dai) +{ + struct snd_soc_pcm_runtime *rtd = substream->private_data; + struct fsl_ssi_private *ssi_private = snd_soc_dai_get_drvdata( + rtd->cpu_dai); + struct ccsr_ssi __iomem *ssi = ssi_private->ssi; + + switch (cmd) { + case SNDRV_PCM_TRIGGER_START: + case SNDRV_PCM_TRIGGER_PAUSE_RELEASE: + if (substream->stream == SNDRV_PCM_STREAM_PLAYBACK) + write_ssi_mask(&ssi->sier, 0, CCSR_SSI_SIER_TIE | + CCSR_SSI_SIER_TFE0_EN); + else + write_ssi_mask(&ssi->sier, 0, CCSR_SSI_SIER_RIE | + CCSR_SSI_SIER_RFF0_EN); + break; + + case SNDRV_PCM_TRIGGER_STOP: + case SNDRV_PCM_TRIGGER_PAUSE_PUSH: + if (substream->stream == SNDRV_PCM_STREAM_PLAYBACK) + write_ssi_mask(&ssi->sier, CCSR_SSI_SIER_TIE | + CCSR_SSI_SIER_TFE0_EN, 0); + else + write_ssi_mask(&ssi->sier, CCSR_SSI_SIER_RIE | + CCSR_SSI_SIER_RFF0_EN, 0); + break; + + default: + return -EINVAL; + } + + if (substream->stream == SNDRV_PCM_STREAM_PLAYBACK) + write_ssi(CCSR_SSI_SOR_TX_CLR, &ssi->sor); + else + write_ssi(CCSR_SSI_SOR_RX_CLR, &ssi->sor); + + return 0; +} + +static const struct snd_soc_dai_ops fsl_ssi_ac97_dai_ops = { + .startup = fsl_ssi_startup, + .shutdown = fsl_ssi_shutdown, + .trigger = fsl_ssi_ac97_trigger, +}; + +static struct snd_soc_dai_driver fsl_ssi_ac97_dai = { + .ac97_control = 1, + .playback = { + .stream_name = "AC97 Playback", + .channels_min = 2, + .channels_max = 2, + .rates = SNDRV_PCM_RATE_8000_48000, + .formats = SNDRV_PCM_FMTBIT_S16_LE, + }, + .capture = { + .stream_name = "AC97 Capture", + .channels_min = 2, + .channels_max = 2, + .rates = SNDRV_PCM_RATE_48000, + .formats = SNDRV_PCM_FMTBIT_S16_LE, + }, + .ops = &fsl_ssi_ac97_dai_ops, +}; + + +static struct fsl_ssi_private *fsl_ac97_data; + +static void fsl_ssi_ac97_init(void) +{ + fsl_ssi_setup(fsl_ac97_data); +} + +void fsl_ssi_ac97_write(struct snd_ac97 *ac97, unsigned short reg, + unsigned short val) +{ + struct ccsr_ssi *ssi = fsl_ac97_data->ssi; + unsigned int lreg; + unsigned int lval; + + if (reg > 0x7f) + return; + + + lreg = reg << 12; + write_ssi(lreg, &ssi->sacadd); + + lval = val << 4; + write_ssi(lval , &ssi->sacdat); + + write_ssi_mask(&ssi->sacnt, CCSR_SSI_SACNT_RDWR_MASK, + CCSR_SSI_SACNT_WR); + udelay(100); +} + +unsigned short fsl_ssi_ac97_read(struct snd_ac97 *ac97, + unsigned short reg) +{ + struct ccsr_ssi *ssi = fsl_ac97_data->ssi; + + unsigned short val = -1; + unsigned int lreg; + + lreg = (reg & 0x7f) << 12; + write_ssi(lreg, &ssi->sacadd); + write_ssi_mask(&ssi->sacnt, CCSR_SSI_SACNT_RDWR_MASK, + CCSR_SSI_SACNT_RD); + + udelay(100); + + val = (read_ssi(&ssi->sacdat) >> 4) & 0xffff; + + return val; +} + +static struct snd_ac97_bus_ops fsl_ssi_ac97_ops = { + .read = fsl_ssi_ac97_read, + .write = fsl_ssi_ac97_write, +}; + /* Show the statistics of a flag only if its interrupt is enabled. The * compiler will optimze this code to a no-op if the interrupt is not * enabled. @@ -663,6 +871,7 @@ static int fsl_ssi_probe(struct platform_device *pdev) struct resource res; char name[64]; bool shared; + bool ac97 = false; /* SSIs that are not connected on the board should have a * status = "disabled" @@ -673,14 +882,20 @@ static int fsl_ssi_probe(struct platform_device *pdev) /* We only support the SSI in "I2S Slave" mode */ sprop = of_get_property(np, "fsl,mode", NULL); - if (!sprop || strcmp(sprop, "i2s-slave")) { + if (!sprop) { + dev_err(&pdev->dev, "fsl,mode property is necessary\n"); + return -EINVAL; + } + if (!strcmp(sprop, "ac97-slave")) { + ac97 = true; + } else if (strcmp(sprop, "i2s-slave")) { dev_notice(&pdev->dev, "mode %s is unsupported\n", sprop); return -ENODEV; } /* The DAI name is the last part of the full name of the node. */ p = strrchr(np->full_name, '/') + 1; - ssi_private = kzalloc(sizeof(struct fsl_ssi_private) + strlen(p), + ssi_private = devm_kzalloc(&pdev->dev, sizeof(*ssi_private) + strlen(p), GFP_KERNEL); if (!ssi_private) { dev_err(&pdev->dev, "could not allocate DAI object\n"); @@ -689,38 +904,41 @@ static int fsl_ssi_probe(struct platform_device *pdev) strcpy(ssi_private->name, p); - /* Initialize this copy of the CPU DAI driver structure */ - memcpy(&ssi_private->cpu_dai_drv, &fsl_ssi_dai_template, - sizeof(fsl_ssi_dai_template)); + ssi_private->use_dma = !of_property_read_bool(np, + "fsl,fiq-stream-filter"); + + if (ac97) { + memcpy(&ssi_private->cpu_dai_drv, &fsl_ssi_ac97_dai, + sizeof(fsl_ssi_ac97_dai)); + + fsl_ac97_data = ssi_private; + ssi_private->imx_ac97 = true; + + snd_soc_set_ac97_ops_of_reset(&fsl_ssi_ac97_ops, pdev); + } else { + /* Initialize this copy of the CPU DAI driver structure */ + memcpy(&ssi_private->cpu_dai_drv, &fsl_ssi_dai_template, + sizeof(fsl_ssi_dai_template)); + } ssi_private->cpu_dai_drv.name = ssi_private->name; /* Get the addresses and IRQ */ ret = of_address_to_resource(np, 0, &res); if (ret) { dev_err(&pdev->dev, "could not determine device resources\n"); - goto error_kmalloc; + return ret; } ssi_private->ssi = of_iomap(np, 0); if (!ssi_private->ssi) { dev_err(&pdev->dev, "could not map device resources\n"); - ret = -ENOMEM; - goto error_kmalloc; + return -ENOMEM; } ssi_private->ssi_phys = res.start; ssi_private->irq = irq_of_parse_and_map(np, 0); if (ssi_private->irq == NO_IRQ) { dev_err(&pdev->dev, "no irq for node %s\n", np->full_name); - ret = -ENXIO; - goto error_iomap; - } - - /* The 'name' should not have any slashes in it. */ - ret = request_irq(ssi_private->irq, fsl_ssi_isr, 0, ssi_private->name, - ssi_private); - if (ret < 0) { - dev_err(&pdev->dev, "could not claim irq %u\n", ssi_private->irq); - goto error_irqmap; + return -ENXIO; } /* Are the RX and the TX clocks locked? */ @@ -739,13 +957,18 @@ static int fsl_ssi_probe(struct platform_device *pdev) u32 dma_events[2]; ssi_private->ssi_on_imx = true; - ssi_private->clk = clk_get(&pdev->dev, NULL); + ssi_private->clk = devm_clk_get(&pdev->dev, NULL); if (IS_ERR(ssi_private->clk)) { ret = PTR_ERR(ssi_private->clk); dev_err(&pdev->dev, "could not get clock: %d\n", ret); - goto error_irq; + goto error_irqmap; + } + ret = clk_prepare_enable(ssi_private->clk); + if (ret) { + dev_err(&pdev->dev, "clk_prepare_enable failed: %d\n", + ret); + goto error_irqmap; } - clk_prepare_enable(ssi_private->clk); /* * We have burstsize be "fifo_depth - 2" to match the SSI @@ -763,24 +986,38 @@ static int fsl_ssi_probe(struct platform_device *pdev) &ssi_private->filter_data_tx; ssi_private->dma_params_rx.filter_data = &ssi_private->filter_data_rx; - /* - * TODO: This is a temporary solution and should be changed - * to use generic DMA binding later when the helplers get in. - */ - ret = of_property_read_u32_array(pdev->dev.of_node, + if (!of_property_read_bool(pdev->dev.of_node, "dmas") && + ssi_private->use_dma) { + /* + * FIXME: This is a temporary solution until all + * necessary dma drivers support the generic dma + * bindings. + */ + ret = of_property_read_u32_array(pdev->dev.of_node, "fsl,ssi-dma-events", dma_events, 2); - if (ret) { - dev_err(&pdev->dev, "could not get dma events\n"); - goto error_clk; + if (ret && ssi_private->use_dma) { + dev_err(&pdev->dev, "could not get dma events but fsl-ssi is configured to use DMA\n"); + goto error_clk; + } } shared = of_device_is_compatible(of_get_parent(np), "fsl,spba-bus"); imx_pcm_dma_params_init_data(&ssi_private->filter_data_tx, - dma_events[0], shared); + dma_events[0], shared ? IMX_DMATYPE_SSI_SP : IMX_DMATYPE_SSI); imx_pcm_dma_params_init_data(&ssi_private->filter_data_rx, - dma_events[1], shared); + dma_events[1], shared ? IMX_DMATYPE_SSI_SP : IMX_DMATYPE_SSI); + } else if (ssi_private->use_dma) { + /* The 'name' should not have any slashes in it. */ + ret = devm_request_irq(&pdev->dev, ssi_private->irq, + fsl_ssi_isr, 0, ssi_private->name, + ssi_private); + if (ret < 0) { + dev_err(&pdev->dev, "could not claim irq %u\n", + ssi_private->irq); + goto error_irqmap; + } } /* Initialize the the device_attribute structure */ @@ -794,7 +1031,7 @@ static int fsl_ssi_probe(struct platform_device *pdev) if (ret) { dev_err(&pdev->dev, "could not create sysfs %s file\n", ssi_private->dev_attr.attr.name); - goto error_irq; + goto error_clk; } /* Register with ASoC */ @@ -808,9 +1045,30 @@ static int fsl_ssi_probe(struct platform_device *pdev) } if (ssi_private->ssi_on_imx) { - ret = imx_pcm_dma_init(pdev); - if (ret) - goto error_dev; + if (!ssi_private->use_dma) { + + /* + * Some boards use an incompatible codec. To get it + * working, we are using imx-fiq-pcm-audio, that + * can handle those codecs. DMA is not possible in this + * situation. + */ + + ssi_private->fiq_params.irq = ssi_private->irq; + ssi_private->fiq_params.base = ssi_private->ssi; + ssi_private->fiq_params.dma_params_rx = + &ssi_private->dma_params_rx; + ssi_private->fiq_params.dma_params_tx = + &ssi_private->dma_params_tx; + + ret = imx_pcm_fiq_init(pdev, &ssi_private->fiq_params); + if (ret) + goto error_dev; + } else { + ret = imx_pcm_dma_init(pdev); + if (ret) + goto error_dev; + } } /* @@ -845,6 +1103,9 @@ static int fsl_ssi_probe(struct platform_device *pdev) } done: + if (ssi_private->imx_ac97) + fsl_ssi_ac97_init(); + return 0; error_dai: @@ -857,23 +1118,12 @@ error_dev: device_remove_file(&pdev->dev, dev_attr); error_clk: - if (ssi_private->ssi_on_imx) { + if (ssi_private->ssi_on_imx) clk_disable_unprepare(ssi_private->clk); - clk_put(ssi_private->clk); - } - -error_irq: - free_irq(ssi_private->irq, ssi_private); error_irqmap: irq_dispose_mapping(ssi_private->irq); -error_iomap: - iounmap(ssi_private->ssi); - -error_kmalloc: - kfree(ssi_private); - return ret; } @@ -883,20 +1133,15 @@ static int fsl_ssi_remove(struct platform_device *pdev) if (!ssi_private->new_binding) platform_device_unregister(ssi_private->pdev); - if (ssi_private->ssi_on_imx) { + if (ssi_private->ssi_on_imx) imx_pcm_dma_exit(pdev); - clk_disable_unprepare(ssi_private->clk); - clk_put(ssi_private->clk); - } snd_soc_unregister_component(&pdev->dev); + dev_set_drvdata(&pdev->dev, NULL); device_remove_file(&pdev->dev, &ssi_private->dev_attr); - - free_irq(ssi_private->irq, ssi_private); + if (ssi_private->ssi_on_imx) + clk_disable_unprepare(ssi_private->clk); irq_dispose_mapping(ssi_private->irq); - kfree(ssi_private); - dev_set_drvdata(&pdev->dev, NULL); - return 0; } @@ -919,6 +1164,7 @@ static struct platform_driver fsl_ssi_driver = { module_platform_driver(fsl_ssi_driver); +MODULE_ALIAS("platform:fsl-ssi-dai"); MODULE_AUTHOR("Timur Tabi <timur@freescale.com>"); MODULE_DESCRIPTION("Freescale Synchronous Serial Interface (SSI) ASoC Driver"); MODULE_LICENSE("GPL v2"); |