summaryrefslogtreecommitdiff
AgeCommit message (Collapse)Author
2010-10-17tcp: use correct counters in CA_CWR state tooIlpo Järvinen
As CWR is stronger than CA_Disorder state, we can miscount SACK/Reno failure into other timeouts. Not a bad problem as it can happen only due to ECN, FRTO detecting spurious RTO or xmit error which are the only callers of tcp_enter_cwr. And even then losses and RTO must still follow thereafter to actually end up into the relevant code paths. Compile tested. Signed-off-by: Ilpo Järvinen <ilpo.jarvinen@helsinki.fi> Signed-off-by: David S. Miller <davem@davemloft.net>
2010-10-17tcp: sack lost marking fixesIlpo Järvinen
When only fast rexmit should be done, tcp_mark_head_lost marks L too far. Also, sacked_upto below 1 is perfectly valid number, the packets == 0 then needs to be trapped elsewhere. Signed-off-by: Ilpo Järvinen <ilpo.jarvinen@helsinki.fi> Signed-off-by: David S. Miller <davem@davemloft.net>
2010-10-17stmmac: remove ifdef NETIF_F_TSO from stmmac_ethtool.cGiuseppe Cavallaro
Signed-off-by: Giuseppe Cavallaro <peppe.cavallaro@st.com> Reported-by: Armando Visconti <armando.visconti@st.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2010-10-17niu: introduce temp variables to avoid sparse warnings when swapping in-situHarvey Harrison
Suppress a large block of warnings like: drivers/net/niu.c:7094:38: warning: incorrect type in assignment (different base types) drivers/net/niu.c:7094:38: expected restricted __be32 [usertype] ip4src drivers/net/niu.c:7094:38: got unsigned long long drivers/net/niu.c:7104:17: warning: cast from restricted __be32 ... Signed-off-by: Harvey Harrison <harvey.harrison@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2010-10-16net: move MII outside of NET_ETHERNET, fix kconfig warningRandy Dunlap
We have USB, PCMCIA, and gigabit ethernet drivers that select MII even though NET_ETHERNET is not enabled, so make MII not be dependent on NET_ETHERNET. It is still dependent on NET and NETDEVICES. Fixes kconfig unmet dependency warning (shortened, was very long string): warning: (ARM_AT91_ETHER && NETDEVICES && NET_ETHERNET && ARM && ARCH_AT91RM9200 || ARM_KS8695_ETHER && NETDEVICES && NET_ETHERNET && ARM && ARCH_KS8695 || ... || IP1000 && NETDEVICES && NETDEV_1000 && PCI && EXPERIMENTAL || HAMACHI && NETDEVICES && NETDEV_1000 && PCI || R8169 && NETDEVICES && NETDEV_1000 && PCI || SIS190 && NETDEVICES && NETDEV_1000 && PCI || VIA_VELOCITY && NETDEVICES && NETDEV_1000 && PCI || ATL1 && NETDEVICES && NETDEV_1000 && PCI || ATL1E && NETDEVICES && NETDEV_1000 && PCI && EXPERIMENTAL || ATL1C && NETDEVICES && NETDEV_1000 && PCI && EXPERIMENTAL || JME && NETDEVICES && NETDEV_1000 && PCI || STMMAC_ETH && NETDEV_1000 && NETDEVICES && HAS_IOMEM || USB_PEGASUS && NETDEVICES && USB && NET || USB_RTL8150 && NETDEVICES && USB && NET && EXPERIMENTAL || USB_USBNET && NETDEVICES && USB && NET || PCMCIA_SMC91C92 && NETDEVICES && NET_PCMCIA && PCMCIA) selects MII which has unmet direct dependencies (NETDEVICES && NET_ETHERNET) Signed-off-by: Randy Dunlap <randy.dunlap@oracle.com> Acked-by: Jeff Garzik <jgarzik@pobox.com> [2006-NOV-30] Signed-off-by: David S. Miller <davem@davemloft.net>
2010-10-16infiniband: fix mlx4 kconfig dependency warningRandy Dunlap
Fix kconfig dependency warning to satisfy dependencies: warning: (MLX4_EN && NETDEVICES && NETDEV_10000 && PCI && INET || MLX4_INFINIBAND && INFINIBAND) selects MLX4_CORE which has unmet direct dependencies (NETDEVICES && NETDEV_10000 && PCI) Signed-off-by: Randy Dunlap <randy.dunlap@oracle.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2010-10-16stmmac: make function tables conststephen hemminger
These tables only contain function pointers. Signed-off-by: Stephen Hemminger <shemminger@vyatta.com> Acked-by: Gustavo F. Padovan <padovan@profusion.mobi> Signed-off-by: David S. Miller <davem@davemloft.net>
2010-10-16stmmac: make ethtool functions localstephen hemminger
Signed-off-by: Stephen Hemminger <shemminger@vyatta.com> Acked-by: Gustavo F. Padovan <padovan@profusion.mobi> Signed-off-by: David S. Miller <davem@davemloft.net>
2010-10-16tipc: cleanup function namespacestephen hemminger
Do some cleanups of TIPC based on make namespacecheck 1. Don't export unused symbols 2. Eliminate dead code 3. Make functions and variables local 4. Rename buf_acquire to tipc_buf_acquire since it is used in several files Compile tested only. This make break out of tree kernel modules that depend on TIPC routines. Signed-off-by: Stephen Hemminger <shemminger@vyatta.com> Acked-by: Jon Maloy <jon.maloy@ericsson.com> Acked-by: Paul Gortmaker <paul.gortmaker@windriver.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2010-10-16via-velocity: forced 1000 Mbps mode support.françois romieu
Full duplex only. Half duplex 1000 Mbps is not supported. Signed-off-by: David Lv <DavidLv@viatech.com.cn> Acked-by: Francois Romieu <romieu@fr.zoreil.com> Tested-by: Seguier Regis <rseguier@e-teleport.net> Signed-off-by: David S. Miller <davem@davemloft.net>
2010-10-16fib: avoid false sharing on fib_table_hashEric Dumazet
While doing profile analysis, I found fib_hash_table was sometime in a cache line shared by a possibly often written kernel structure. (CONFIG_IP_ROUTE_MULTIPATH || !CONFIG_IPV6_MULTIPLE_TABLES) It's hard to detect because not easily reproductible. Make sure we allocate a full cache line to keep this shared in all cpus caches. Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2010-10-16fib_trie: use fls() instead of open coded loopEric Dumazet
fib_table_lookup() might use fls() to speedup an open coded loop. Noticed while doing a profile analysis. Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2010-10-16fib: remove a useless synchronize_rcu() callEric Dumazet
fib_nl_delrule() calls synchronize_rcu() for no apparent reason, while rtnl is held. I suspect it was done to avoid an atomic_inc_not_zero() in fib_rules_lookup(), which commit 7fa7cb7109d07 added anyway. Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2010-10-16fib6: use FIB_LOOKUP_NOREF in fib6_rule_lookup()Eric Dumazet
Avoid two atomic ops on found rule in fib6_rule_lookup() Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2010-10-16sundance: Add initial ethtool stats supportDenis Kirjanov
Add ethtool stats support. Signed-off-by: Denis Kirjanov <dkirjanov@kernel.org> Acked-by: Eric Dumazet <eric.dumazet@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2010-10-16pch_gbe: fix if condition in set_settings()Dan Carpenter
There were no curly braces in this if condition so it always enabled full duplex. And ecmd->speed is an unsigned short so it is never equal to -1. The effect is that mii_ethtool_sset() fails with -EINVAL and an error is printed to dmesg. Signed-off-by: Dan Carpenter <error27@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2010-10-16dnet: mark methods static and annotate for correct endiannessHarvey Harrison
Their doesn't appear to be bugs with the endianness handling here, just get the annotations right to keep sparse happy. Suppresses the following sparse warnings: drivers/net/dnet.c:30:5: warning: symbol 'dnet_readw_mac' was not declared. Should it be static? drivers/net/dnet.c:49:6: warning: symbol 'dnet_writew_mac' was not declared. Should it be static? drivers/net/dnet.c:364:5: warning: symbol 'dnet_phy_marvell_fixup' was not declared. Should it be static? drivers/net/dnet.c:66:13: warning: incorrect type in assignment (different base types) drivers/net/dnet.c:66:13: expected unsigned short [unsigned] [usertype] tmp drivers/net/dnet.c:66:13: got restricted __be16 [usertype] <noident> drivers/net/dnet.c:68:13: warning: incorrect type in assignment (different base types) drivers/net/dnet.c:68:13: expected unsigned short [unsigned] [usertype] tmp drivers/net/dnet.c:68:13: got restricted __be16 [usertype] <noident> drivers/net/dnet.c:70:13: warning: incorrect type in assignment (different base types) drivers/net/dnet.c:70:13: expected unsigned short [unsigned] [usertype] tmp drivers/net/dnet.c:70:13: got restricted __be16 [usertype] <noident> drivers/net/dnet.c:92:27: warning: cast to restricted __be16 drivers/net/dnet.c:94:33: warning: cast to restricted __be16 drivers/net/dnet.c:96:33: warning: cast to restricted __be16 Signed-off-by: Harvey Harrison <harvey.harrison@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2010-10-16cxgb4vf: make single bit signed bitfields unsignedHarvey Harrison
Single bit signed bitfields don't make a lot of sense, noticed by sparse: drivers/net/cxgb4vf/t4vf_common.h:135:31: error: dubious one-bit signed bitfield drivers/net/cxgb4vf/t4vf_common.h:136:36: error: dubious one-bit signed bitfield drivers/net/cxgb4vf/t4vf_common.h:137:36: error: dubious one-bit signed bitfield drivers/net/cxgb4vf/t4vf_common.h:138:36: error: dubious one-bit signed bitfield drivers/net/cxgb4vf/t4vf_common.h:139:36: error: dubious one-bit signed bitfield drivers/net/cxgb4vf/t4vf_common.h:140:31: error: dubious one-bit signed bitfield drivers/net/cxgb4vf/t4vf_common.h:141:31: error: dubious one-bit signed bitfield drivers/net/cxgb4vf/t4vf_common.h:142:35: error: dubious one-bit signed bitfield drivers/net/cxgb4vf/t4vf_common.h:143:35: error: dubious one-bit signed bitfield drivers/net/cxgb4vf/t4vf_common.h:154:27: error: dubious one-bit signed bitfield drivers/net/cxgb4vf/t4vf_common.h:155:26: error: dubious one-bit signed bitfield drivers/net/cxgb4vf/t4vf_common.h:156:27: error: dubious one-bit signed bitfield drivers/net/cxgb4vf/t4vf_common.h:157:26: error: dubious one-bit signed bitfield Signed-off-by: Harvey Harrison <harvey.harrison@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2010-10-16net: allocate skbs on local nodeEric Dumazet
commit b30973f877 (node-aware skb allocation) spread a wrong habit of allocating net drivers skbs on a given memory node : The one closest to the NIC hardware. This is wrong because as soon as we try to scale network stack, we need to use many cpus to handle traffic and hit slub/slab management on cross-node allocations/frees when these cpus have to alloc/free skbs bound to a central node. skb allocated in RX path are ephemeral, they have a very short lifetime : Extra cost to maintain NUMA affinity is too expensive. What appeared as a nice idea four years ago is in fact a bad one. In 2010, NIC hardwares are multiqueue, or we use RPS to spread the load, and two 10Gb NIC might deliver more than 28 million packets per second, needing all the available cpus. Cost of cross-node handling in network and vm stacks outperforms the small benefit hardware had when doing its DMA transfert in its 'local' memory node at RX time. Even trying to differentiate the two allocations done for one skb (the sk_buff on local node, the data part on NIC hardware node) is not enough to bring good performance. Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com> Acked-by: Tom Herbert <therbert@google.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2010-10-16r8169: use 50% less ram for RX ringEric Dumazet
Using standard skb allocations in r8169 leads to order-3 allocations (if PAGE_SIZE=4096), because NIC needs 16383 bytes, and skb overhead makes this bigger than 16384 -> 32768 bytes per "skb" Using kmalloc() permits to reduce memory requirements of one r8169 nic by 4Mbytes. (256 frames * 16Kbytes). This is fine since a hardware bug requires us to copy incoming frames, so we build real skb when doing this copy. Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2010-10-15ixgbe: DCB: remove DCB check configJohn Fastabend
Remove a DCB check config from DCB configuration we continue to configure DCB even if it fails so don't even bother to check. Plus user space (lldpad) checks this before programming the hw anyways. Worse case is we program some values into the hw that don't make total sense resulting in incorrect bandwidth allocation. Signed-off-by: John Fastabend <john.r.fastabend@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2010-10-14igb: add check for fiber/serdes devices to igb_set_spd_dplx;Carolyn Wyborny
Signed-off-by: Carolyn Wyborny <carolyn.wyborny@intel.com> Tested-by: Emil Tantilov <emil.s.tantilov@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2010-10-14ixgbe: declare functions as staticEmil Tantilov
Following patch fixes warnings reported by `make namespacecheck` Reported by Stephen Hemminger CC: Stephen Hemminger <shemminger@vyatta.com> Signed-off-by: Emil Tantilov <emil.s.tantilov@intel.com> Tested-by: Stephen Ko <stephen.s.ko@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2010-10-14ixgbe: remove unused functionsEmil Tantilov
Remove functions that are declared, but not used in the driver. This patch fixes warnings reported by `make namespacecheck` Reported by Stephen Hemminger CC: Stephen Hemminger <shemminger@vyatta.com> Signed-off-by: Emil Tantilov <emil.s.tantilov@intel.com> Tested-by: Stephen Ko <stephen.s.ko@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2010-10-14cnic: Add support for 57712 deviceMichael Chan
Add new interrupt ack functions and other hardware interface logic to support the new device. Update version to 2.2.6. Signed-off-by: Michael Chan <mchan@broadcom.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2010-10-14cnic: Decouple uio close from cnic shutdownMichael Chan
During cnic shutdown, the original driver code requires userspace to close the uio device within a few seconds. This doesn't always happen as the userapp may be hung or otherwise take a long time to close. The system may crash when this happens. We fix the problem by decoupling the uio structures from the cnic structures during cnic shutdown. We do not unregister the uio device until the cnic driver is unloaded. This eliminates the unreliable wait loop for uio to close. All uio structures are kept in a linked list. If the device is shutdown and later brought back up again, the uio strcture will be found in the linked list and coupled back to the cnic structures. Signed-off-by: Michael Chan <mchan@broadcom.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2010-10-14cnic: Add cnic_uio_dev structMichael Chan
and put all uio related structures and ring buffers in it. This allows uio operations to be done independent of the cnic device structures. Signed-off-by: Michael Chan <mchan@broadcom.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2010-10-14cnic: Add cnic_free_uio()Michael Chan
to free all UIO related structures. Signed-off-by: Michael Chan <mchan@broadcom.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2010-10-14cnic: Defer iscsi connection cleanupMichael Chan
The bnx2x devices require a 2 second quiet time before sending the last RAMROD command to destroy a connection. This sleep wait adds up to a long delay when iscsid is serially destroying maultiple connections. Create a workqueue to perform the final connection cleanup in the background to speed up the process. This significantly speeds up the process as the wait time can be done in parallel for multiple connections. Signed-off-by: Michael Chan <mchan@broadcom.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2010-10-14cnic: Add cnic_bnx2x_destroy_ramrod()Michael Chan
Refactoring code for the next patch to defer connection clean up. Signed-off-by: Michael Chan <mchan@broadcom.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2010-10-14cnic: Convert ctx_flags to bit fieldsMichael Chan
so that we can additional bit definitions without requiring a spinlock. Signed-off-by: Michael Chan <mchan@broadcom.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2010-10-14cnic: Add common cnic_request_irq()Michael Chan
to reduce some duplicate code. Also, use tasklet_kill() in cnic_free_irq() to wait for the cnic_irq_task to complete. Signed-off-by: Michael Chan <mchan@broadcom.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2010-10-13Documentation: Update Phonet doc for Pipe controller changesKumar Sanghvi
Updates to Phonet doc for Pipe controller 'connect' socket implementation and changes related to socket options. Signed-off-by: Kumar Sanghvi <kumar.sanghvi@stericsson.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2010-10-13Phonet: 'connect' socket implementation for Pipe controllerKumar Sanghvi
Based on suggestion by Rémi Denis-Courmont to implement 'connect' for Pipe controller logic, this patch implements 'connect' socket call for the Pipe controller logic. The patch does following:- - Removes setsockopts for PNPIPE_CREATE and PNPIPE_DESTROY - Adds setsockopt for setting the Pipe handle value - Implements connect socket call - Updates the Pipe controller logic User-space should now follow below sequence with Pipe controller:- -socket -bind -setsockopt for PNPIPE_PIPE_HANDLE -connect -setsockopt for PNPIPE_ENCAP_IP -setsockopt for PNPIPE_ENABLE GPRS/3G data has been tested working fine with this. Signed-off-by: Kumar Sanghvi <kumar.sanghvi@stericsson.com> Acked-by: Rémi Denis-Courmont <remi.denis-courmont@nokia.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2010-10-13tipc: clean out all instances of #if 0'd unused codePaul Gortmaker
Remove all instances of legacy, or as yet to be implemented code that is currently living within an #if 0 ... #endif block. In the rare instance that some of it be needed in the future, it can still be dragged out of history, but there is no need for it to sit in mainline. Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com> Acked-by: Neil Horman <nhorman@tuxdriver.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2010-10-13s390: ctcm_mpc: Fix build after netdev refcount changes.David S. Miller
Reported-by: Sachin Sant <sachinp@in.ibm.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2010-10-12net: percpu net_device refcountEric Dumazet
We tried very hard to remove all possible dev_hold()/dev_put() pairs in network stack, using RCU conversions. There is still an unavoidable device refcount change for every dst we create/destroy, and this can slow down some workloads (routers or some app servers, mmap af_packet) We can switch to a percpu refcount implementation, now dynamic per_cpu infrastructure is mature. On a 64 cpus machine, this consumes 256 bytes per device. On x86, dev_hold(dev) code : before lock incl 0x280(%ebx) after: movl 0x260(%ebx),%eax incl fs:(%eax) Stress bench : (Sending 160.000.000 UDP frames, IP route cache disabled, dual E5540 @2.53GHz, 32bit kernel, FIB_TRIE) Before: real 1m1.662s user 0m14.373s sys 12m55.960s After: real 0m51.179s user 0m15.329s sys 10m15.942s Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2010-10-12bnx2x: Fixing a typo: added a missing RSS enablementDmitry Kravkov
Reported-by: Eric Dumazet <eric.dumazet@gmail.com> Signed-off-by: Dmitry Kravkov <dmitry@broadcom.com> Signed-off-by: Vladislav Zolotarov <vladz@broadcom.com> Tested-by: Eric Dumazet <eric.dumazet@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2010-10-12Merge branch 'dccp' of git://eden-feed.erg.abdn.ac.uk/net-next-2.6David S. Miller
2010-10-12dccp: cosmetics - warning formatGerrit Renker
This omits the redundant "DCCP:" in warning messages, since DCCP_WARN() already echoes the function name, avoiding messages like kernel: [10988.766503] dccp_close: DCCP: ABORT -- 209 bytes unread Signed-off-by: Gerrit Renker <gerrit@erg.abdn.ac.uk>
2010-10-12dccp: schedule an Ack when receiving timestampsGerrit Renker
This schedules an Ack when receiving a timestamp, exploiting the existing inet_csk_schedule_ack() function, saving one case in the `dccp_ack_pending()' function. Signed-off-by: Gerrit Renker <gerrit@erg.abdn.ac.uk>
2010-10-12dccp: generalise data-loss conditionIvo Calado
This patch generalises the task of determining data loss from RFC 4340, 7.7.1. Let S_A, S_B be sequence numbers such that S_B is "after" S_A, and let N_B be the NDP count of packet S_B. Then, using modulo-2^48 arithmetic, D = S_B - S_A - 1 is an upper bound of the number of lost data packets, D - N_B is an approximation of the number of lost data packets (there are cases where this is not exact). The patch implements this as dccp_loss_count(S_A, S_B, N_B) := max(S_B - S_A - 1 - N_B, 0) Signed-off-by: Ivo Calado <ivocalado@embedded.ufcg.edu.br> Signed-off-by: Erivaldo Xavier <desadoc@gmail.com> Signed-off-by: Leandro Sales <leandroal@gmail.com> Signed-off-by: Gerrit Renker <gerrit@erg.abdn.ac.uk>
2010-10-12dccp: remove unused argument in CCID tx functionGerrit Renker
This removes the argument `more' from ccid_hc_tx_packet_sent, since it was nowhere used in the entire code. (Btw, this argument was not even used in the original KAME code where the function initially came from; compare the variable moreToSend in the freebsd61-dccp-kame-28.08.2006.patch kept by Emmanuel Lochin.) Signed-off-by: Gerrit Renker <gerrit@erg.abdn.ac.uk>
2010-10-12dccp: merge now-reduced connect_init() functionGerrit Renker
After moving the assignment of GAR/ISS from dccp_connect_init() to dccp_transmit_skb(), the former function becomes very small, so that a merger with dccp_connect() suggests itself. Signed-off-by: Gerrit Renker <gerrit@erg.abdn.ac.uk>
2010-10-12dccp: fix the adjustments to AWL and SWLGerrit Renker
This fixes a problem and a potential loophole with regard to seqno/ackno validity: currently the initial adjustments to AWL/SWL are only performed once at the begin of the connection, during the handshake. Since the Sequence Window feature is always greater than Wmin=32 (7.5.2), it is however necessary to perform these adjustments at least for the first W/W' (variables as per 7.5.1) packets in the lifetime of a connection. This requirement is complicated by the fact that W/W' can change at any time during the lifetime of a connection. Therefore it is better to perform that safety check each time SWL/AWL are updated, as implemented by the patch. A second problem solved by this patch is that the remote/local Sequence Window feature values (which set the bounds for AWL/SWL/SWH) are undefined until the feature negotiation has completed. During the initial handshake we have more stringent sequence number protection; the changes added by this patch effect that {A,S}W{L,H} are within the correct bounds at the instant that feature negotiation completes (since the SeqWin feature activation handlers call dccp_update_gsr/gss()). Signed-off-by: Gerrit Renker <gerrit@erg.abdn.ac.uk>
2010-10-11bnx2: Enable AER on PCIE devices onlyMichael Chan
To prevent unnecessary error message. pci_save_state() is also moved to the end of ->probe() so that all PCI config, including AER state, will be saved. Update version to 2.0.18. Signed-off-by: Michael Chan <mchan@broadcom.com> Reviewed-by: Benjamin Li <mchan@broadcom.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2010-10-11bnx2: Update firmware to 6.0.x.Michael Chan
- Improved flow control and simplified interface - Use hardware RSS indirection table instead of the slower firmware- based table - Lower latency interrupt on 5709 Signed-off-by: Michael Chan <mchan@broadcom.com> Reviewed-by: Benjamin Li <benli@broadcom.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2010-10-11neigh: reorder struct neighbour fieldsEric Dumazet
Le mardi 12 octobre 2010 à 00:02 +0200, Eric Dumazet a écrit : > Here is the followup patch. > > Thanks ! > Oops, this was an old version, the up2date ones also took care of "used" field. I guess its time for a sleep, sorry again. [PATCH net-next V2] neigh: reorder struct neighbour fields (refcnt) and (ha_lock, ha, used, dev, output, ops, primary_key) should be placed on a separate cache lines. refcnt can be often written, while other fields are mostly read. This gave me good result on stress test : before: real 0m45.570s user 0m15.525s sys 9m56.669s After: real 0m41.841s user 0m15.261s sys 8m45.949s Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2010-10-11net dst: use a percpu_counter to track entriesEric Dumazet
struct dst_ops tracks number of allocated dst in an atomic_t field, subject to high cache line contention in stress workload. Switch to a percpu_counter, to reduce number of time we need to dirty a central location. Place it on a separate cache line to avoid dirtying read only fields. Stress test : (Sending 160.000.000 UDP frames, IP route cache disabled, dual E5540 @2.53GHz, 32bit kernel, FIB_TRIE, SLUB/NUMA) Before: real 0m51.179s user 0m15.329s sys 10m15.942s After: real 0m45.570s user 0m15.525s sys 9m56.669s With a small reordering of struct neighbour fields, subject of a following patch, (to separate refcnt from other read mostly fields) real 0m41.841s user 0m15.261s sys 8m45.949s Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2010-10-11neigh: Protect neigh->ha[] with a seqlockEric Dumazet
Add a seqlock in struct neighbour to protect neigh->ha[], and avoid dirtying neighbour in stress situation (many different flows / dsts) Dirtying takes place because of read_lock(&n->lock) and n->used writes. Switching to a seqlock, and writing n->used only on jiffies changes permits less dirtying. Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
generated by cgit v1.2.3 (git 2.0.4) at 2024-09-10 03:46:56 +0000