| Age | Commit message (Collapse) | Author |
|---|
|
New driver for Qualcomm QuadSPI(QSPI) controller that is used to
communicate with slaves such as flash memory devices. The QSPI controller
can operate in 2 or 4 wire mode but only supports SPI Mode 0. The
controller can also operate in Single or Dual data rate modes.
Signed-off-by: Girish Mahadevan <girishm@codeaurora.org>
Signed-off-by: Ryan Case <ryandcase@chromium.org>
Reviewed-by: Douglas Anderson <dianders@chromium.org>
Reviewed-by: Stephen Boyd <swboyd@chromium.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
Bindings for Qualcomm Quad SPI used on SoCs such as sdm845.
Signed-off-by: Girish Mahadevan <girishm@codeaurora.org>
Signed-off-by: Ryan Case <ryandcase@chromium.org>
Reviewed-by: Douglas Anderson <dianders@chromium.org>
Reviewed-by: Rob Herring <robh@kernel.org>
Reviewed-by: Stephen Boyd <swboyd@chromium.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
Add support for a new devicetree compatible string called
'amazon,alpine-apb-ssi', which is necessary for the Amazon Alpine spi
controller. 'amazon,alpine-dw-apb-ssi' is used in the dw spi driver if
specified in the devicetree. Otherwise, fall back to driver default
behavior, i.e. original dw IP hw driver behavior.
Signed-off-by: Talel Shenhar <talel@amazon.com>
Signed-off-by: David Woodhouse <dwmw@amazon.co.uk>
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
This compatible adds the ability for dw spi controller driver to work with
the dw spi controller found on Alpine chips.
The dw spi controller has an auto-deselect of Chip-Select, in case there is
no data inside the Tx FIFO. While working on platforms with Alpine chips,
auto-deselect mode causes an issue for some spi devices that can't handle
the Chip-Select deselect in the middle of a transaction. It is a normal
behavior for a Tx FIFO to be empty in the middle of a transaction, due to
busy cpu. In the Alpine chip family an option to change the default
behavior was added to the original dw spi controller to prevent this issue
of de-asserting Chip-Select once TX FIFO is empty. The change was to allow
SW manual control of the Chip-Select. With this change, as long as the
Slave Enable Register is asserted, the Chip-Select will be asserted. As a
result, it is necessary to deselect the Slave Select Register once the
transaction is done. This feature is enabled via a new device compatible
string called 'amazon,alpine-dw-apb-ssi'. Once the driver identifies the
new compatible string, it enables the hw fixup logic, by writing to a
dedicated register found in the IP reserved area and will start manual
deselecting the Slave Select Register when the transfer ends.
Signed-off-by: Talel Shenhar <talel@amazon.com>
Signed-off-by: David Woodhouse <dwmw@amazon.co.uk>
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/agross/linux into spi-4.20
Immutable branch for QCOM Geni patches
|
|
spidev will make a big fuss if a device tree node binds a device by
using "spidev" as the node's compatible property.
However, the logic for this isn't looking for "spidev" in the
compatible, but rather checking that the device is NOT compatible with
spidev's list of devices.
This causes a false positive if a device not named "rohm,dh2228fv", etc.
binds to spidev, even if a means other than putting "spidev" in the
device tree was used. E.g., the sysfs driver_override attribute.
Signed-off-by: Trent Piepho <tpiepho@impinj.com>
Reviewed-by: Jan Kundrát <jan.kundrat@cesnet.cz>
Tested-by: Jan Kundrát <jan.kundrat@cesnet.cz>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
This attribute works the same was as the identically named attribute
for PCI, AMBA, and platform devices. For reference, see:
commit 3cf385713460 ("ARM: 8256/1: driver coamba: add device binding
path 'driver_override'")
commit 3d713e0e382e ("driver core: platform: add device binding path
'driver_override'")
commit 782a985d7af2 ("PCI: Introduce new device binding path using
pci_dev.driver_override")
If the name of a driver is written to this attribute, then the device
will bind to the named driver and only the named driver.
The device will bind to the driver even if the driver does not list the
device in its id table. This behavior is different than the driver's
bind attribute, which only allows binding to devices that are listed as
supported by the driver.
It can be used to bind a generic driver, like spidev, to a device.
Signed-off-by: Trent Piepho <tpiepho@impinj.com>
Reviewed-by: Jan Kundrát <jan.kundrat@cesnet.cz>
Tested-by: Jan Kundrát <jan.kundrat@cesnet.cz>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
Improve readability a bit.
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
Certain devices don't work well when a transmit FIFO underrun or
receive FIFO overrun occurs. Example is the SAF400x radio chip when
running at high speed which leads to garbage being sent to/received from
the chip. In which case, it should stall waiting for further data to be
available before proceeding. This patch unset the NOSTALL bit in CFGR1
by default to prevent this issue.
Signed-off-by: Hieu Tran Dang <dangtranhieu2012@gmail.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
Clang warns when one enumerated type is implicitly converted to another.
drivers/spi/spi-ep93xx.c:342:62: warning: implicit conversion from
enumeration type 'enum dma_transfer_direction' to different enumeration
type 'enum dma_data_direction' [-Wenum-conversion]
nents = dma_map_sg(chan->device->dev, sgt->sgl, sgt->nents, dir);
~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~^~~~
./include/linux/dma-mapping.h:428:58: note: expanded from macro
'dma_map_sg'
#define dma_map_sg(d, s, n, r) dma_map_sg_attrs(d, s, n, r, 0)
~~~~~~~~~~~~~~~~ ^
drivers/spi/spi-ep93xx.c:348:57: warning: implicit conversion from
enumeration type 'enum dma_transfer_direction' to different enumeration
type 'enum dma_data_direction' [-Wenum-conversion]
dma_unmap_sg(chan->device->dev, sgt->sgl, sgt->nents, dir);
~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~^~~~
./include/linux/dma-mapping.h:429:62: note: expanded from macro
'dma_unmap_sg'
#define dma_unmap_sg(d, s, n, r) dma_unmap_sg_attrs(d, s, n, r, 0)
~~~~~~~~~~~~~~~~~~ ^
drivers/spi/spi-ep93xx.c:377:56: warning: implicit conversion from
enumeration type 'enum dma_transfer_direction' to different enumeration
type 'enum dma_data_direction' [-Wenum-conversion]
dma_unmap_sg(chan->device->dev, sgt->sgl, sgt->nents, dir);
~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~^~~~
./include/linux/dma-mapping.h:429:62: note: expanded from macro
'dma_unmap_sg'
#define dma_unmap_sg(d, s, n, r) dma_unmap_sg_attrs(d, s, n, r, 0)
~~~~~~~~~~~~~~~~~~ ^
3 warnings generated.
dma_{,un}map_sg expect an enum of type dma_data_direction but this
driver uses dma_transfer_direction for everything. Convert the driver to
use dma_data_direction for these two functions.
There are two places that strictly require an enum of type
dma_transfer_direction: the direction member in struct dma_slave_config
and the direction parameter in dmaengine_prep_slave_sg. To avoid using
an explicit cast, add a simple function, ep93xx_dma_data_to_trans_dir,
to safely map between the two types because they are not 1 to 1 in
meaning.
Signed-off-by: Nathan Chancellor <natechancellor@gmail.com>
Reviewed-by: Nick Desaulniers <ndesaulniers@google.com>
Reviewed-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
With this commit the DSPI driver on the BK4 board can be used for SPI
transmission managed from user space (via /dev/spidev0.0).
Example usage/testing:
insmod ./spi-fsl-dspi.ko
./spidev_test -D /dev/spidev0.0 -s 3000000 -v -H -b 8 -p "\xCC\x11\x22\x74"
Signed-off-by: Lukasz Majewski <lukma@denx.de>
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
Rewrite switch code block to directly do the expected number
of shifts in each case and have break statements.
Addresses-Coverity-ID: 1056539 ("Missing break in switch")
Suggested-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Gustavo A. R. Silva <gustavo@embeddedor.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
Apparently, this code does not actually fall through to the next case
because the machine restarts before it has a chance. However, for the
sake of maintenance and readability, we better add the missing break
statement.
Addresses-Coverity-ID: 1437892 ("Missing break in switch")
Signed-off-by: Gustavo A. R. Silva <gustavo@embeddedor.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
Document RZ/G1N (R8A7744) SoC bindings.
Signed-off-by: Biju Das <biju.das@bp.renesas.com>
Reviewed-by: Chris Paterson <Chris.Paterson2@renesas.com>
Reviewed-by: Simon Horman <horms+renesas@verge.net.au>
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
Document RZ/G1N (r8a7744) SoC specific bindings.
Signed-off-by: Biju Das <biju.das@bp.renesas.com>
Reviewed-by: Chris Paterson <Chris.Paterson2@renesas.com>
Reviewed-by: Simon Horman <horms+renesas@verge.net.au>
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
This patch adds basic spi slave for MT2712.
Signed-off-by: Leilk Liu <leilk.liu@mediatek.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
This patch adds a DT binding documentation for the MT2712 soc.
Signed-off-by: Leilk Liu <leilk.liu@mediatek.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
Use the appropriate SPDX license identifier and drop the previous
license text.
Signed-off-by: Marco Felsch <m.felsch@pengutronix.de>
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
On r8a7791/koelsch:
m25p80 spi0.0: error -22 reading 9f
m25p80: probe of spi0.0 failed with error -22
Apparently the logic in spi_mem_check_op() is wrong, rejecting the
spi-mem operation if any buswidth is valid, instead of invalid.
Fixes: 380583227c0c7f52 ("spi: spi-mem: Add extra sanity checks on the op param")
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Boris Brezillon <boris.brezillon@bootlin.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
Add support for RZ/A2
Signed-off-by: Chris Brandt <chris.brandt@renesas.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
The __exit section is left out for built-in drivers, so a
'remove' callback must not be marked as such to avoid breaking when
we unbind a device at runtime. This was pointed out by kbuild:
`sprd_spi_remove' referenced in section `.data' of drivers/spi/spi-sprd.o: defined in discarded section `.exit.text' of drivers/spi/spi-sprd.o
Fixes: e7d973a31c24 ("spi: sprd: Add SPI driver for Spreadtrum SC9860")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Baolin Wang <baolin.wang@linaro.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
The geni_se_clk_freq_match() has some strange semantics. Specifically
it is defined with two modes:
1. It can find a clock that's an exact multiple of the requested rate
2. It can find a non-exact match but it can't handle multiples then
...but callers should always be able to handle a clock that is a
multiple of the requested clock so mode #2 doesn't really make sense.
Let's change the semantics so that the non-exact match can also accept
multiples and then change the code to handle that.
The only caller of this code is the unlanded SPI driver [1] which
currently passes "exact = True", thus it should be safe to change the
semantics in this way. ...and, in fact, the SPI driver should likely
be modified to pass "exact = False" (with the new semantics) since
that will allow it to work with SPI devices that request a clock rate
that doesn't exactly match a rate we can make.
[1] https://lkml.kernel.org/r/1535107336-2214-1-git-send-email-dkota@codeaurora.org
Fixes: eddac5af0654 ("soc: qcom: Add GENI based QUP Wrapper driver")
Signed-off-by: Douglas Anderson <dianders@chromium.org>
Reviewed-by: Matthias Kaehlcke <mka@chromium.org>
Signed-off-by: Andy Gross <andy.gross@linaro.org>
|
|
The function clk_round_rate() is defined to return a "long", not an
"unsigned long". That's because it might return a negative error
code. Change the call in geni_se_clk_tbl_get() to check for errors.
While we're at it, get rid of a useless init of "freq".
NOTE: overall the idea that we should iterate over clk_round_rate() to
try to reconstruct a table already present in the clock driver is
questionable. Specifically:
- This method relies on "clk_round_rate()" rounding up.
- This method only works if the table is sorted and has no duplicates.
...this patch doesn't try to fix those problems, it just makes the
error handling more correct.
Fixes: eddac5af0654 ("soc: qcom: Add GENI based QUP Wrapper driver")
Signed-off-by: Douglas Anderson <dianders@chromium.org>
Reviewed-by: Matthias Kaehlcke <mka@chromium.org>
Signed-off-by: Andy Gross <andy.gross@linaro.org>
|
|
This macro doesn't work, because it hides a local variable inside of the
macro to hold the version and that variable name is called 'ver' and
'version' sometimes.
Let's change this to be more explicit. Introduce three macros for the
major, minor, and step of the version, and require callers to pass the
version in to get the part of the version out. This way we don't hide
local variables inside macros and things are less evil overall.
Cc: Karthikeyan Ramasubramanian <kramasub@codeaurora.org>
Cc: Sagar Dharia <sdharia@codeaurora.org>
Cc: Girish Mahadevan <girishm@codeaurora.org>
Signed-off-by: Stephen Boyd <swboyd@chromium.org>
Reviewed-by: Douglas Anderson <dianders@chromium.org>
Reviewed-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Andy Gross <andy.gross@linaro.org>
|
|
Clang warns when one enumerated type is converted implicitly to another:
drivers/spi/spi-pic32.c:323:8: warning: implicit conversion from
enumeration type 'enum dma_data_direction' to different enumeration type
'enum dma_transfer_direction' [-Wenum-conversion]
DMA_FROM_DEVICE,
^~~~~~~~~~~~~~~
drivers/spi/spi-pic32.c:333:8: warning: implicit conversion from
enumeration type 'enum dma_data_direction' to different enumeration type
'enum dma_transfer_direction' [-Wenum-conversion]
DMA_TO_DEVICE,
^~~~~~~~~~~~~
2 warnings generated.
Use the proper enums from dma_transfer_direction (DMA_FROM_DEVICE =
DMA_DEV_TO_MEM = 2, DMA_TO_DEVICE = DMA_MEM_TO_DEV = 1) to satify Clang.
Link: https://github.com/ClangBuiltLinux/linux/issues/159
Signed-off-by: Nathan Chancellor <natechancellor@gmail.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
Some combinations are simply not valid and should be rejected before
the op is passed to the SPI controller driver.
Add an spi_mem_check_op() helper and use it in spi_mem_exec_op() and
spi_mem_supports_op() to make sure the spi-mem operation is valid.
Signed-off-by: Boris Brezillon <boris.brezillon@bootlin.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
This remove the check and subsequent return of error for the case when
a SPI device requires SPI_CS_WORD and is also configured to use a GPIO
for the CS line.
Commit a134cc414e86 ("spi: always use software fallback for SPI_CS_WORD
when using cs_gio") handles this case now, so this check is no longer
necessary.
Signed-off-by: David Lechner <david@lechnology.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
This modifies the condition for using the software fallback
implementation for SPI_CS_WORD when the SPI controller is using a GPIO
for the CS line. When using a GPIO for CS, the hardware implementation
won't work, so we just enable the software fallback globally in this
case.
Signed-off-by: David Lechner <david@lechnology.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
Mediatek SPI driver modifies some fields (tx_buf, rx_buf, len, tx_dma,
rx_dma) of the spi_transfer* passed in when doing transfer_one and in
interrupt handler. This is somewhat unexpected, and there are some
caller (e.g. Cr50 spi driver) that reuse the spi_transfer for multiple
messages. Add a field to record how many bytes have been transferred,
and calculate the right len / buffer based on it instead.
Signed-off-by: Pi-Hsun Shih <pihsun@chromium.org>
Change-Id: I23e218cd964f16c0b2b26127d4a5ca6529867673
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
If the pll clock needs to be enabled to get its rate, it will also need
to be enabled to provide it. So ensure it is kept enabled through the
lifetime of the device.
Fixes: 0d7412ed1f5dc ("spi/bcm63xx-hspi: Enable the clock before calling clk_get_rate().")
Signed-off-by: Jonas Gorski <jonas.gorski@gmail.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
It makes no sense to remove the device on shutdown. And it break things
when the hardware crucial for shutdown (such as the embedded controller)
is attached to the SPI bus.
Signed-off-by: Lubomir Rintel <lkundrak@v3.sk>
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
This adds support for the SPI_CS_WORD flag to the TI DaVinci SPI
driver. This mode can be used as long as we are using the hardware
chip select and not a GPIO chip select.
Signed-off-by: David Lechner <david@lechnology.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
spi: Provide SPI_CS_WORD
This provides a SPI operation mode which changes chip select after every
word, used by some devices such as ADCs and DACs.
|
|
This adds a default software implementation for the SPI_CS_WORD flag for
controllers that don't have such a feature.
The SPI_CS_WORD flag indicates that the CS line should be toggled
between each word sent, not just between each transfer. The
implementation works by using existing functions to split transfers into
one-word-sized transfers and sets the cs_change bit for each of the
new transfers.
Signed-off-by: David Lechner <david@lechnology.com>
Acked-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
This adds a new SPI mode flag, SPI_CS_WORD, that is used to indicate
that a SPI device requires the chip select to be toggled after each
word that is transferred.
Signed-off-by: David Lechner <david@lechnology.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
Almost all spi drivers assign spi master->dev.of_node from
its parent platform device without additional refcounting.
It seems of_node_get() in pic32_sqi_probe() is unnecessary
and there is no corresponding of_node_put().
Found by Linux Driver Verification project (linuxtesting.org)
Signed-off-by: Alexey Khoroshilov <khoroshilov@ispras.ru>
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
Fixes gcc '-Wunused-but-set-variable' warning:
drivers/spi/spi-davinci.c: In function 'davinci_spi_setup':
drivers/spi/spi-davinci.c:422:36: warning:
variable 'pdata' set but not used [-Wunused-but-set-variable]
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
The DaVinci SPI can use either:
- Internal chip selects (inside the SPI host)
- External chip selects (using GPIO)
- External chip selects passed in pdata
The last way of passing external chip selects through
platform data is not used in the kernel. Delete it to make
the code simpler when refactoring GPIO.
Cc: Sekhar Nori <nsekhar@ti.com>
Cc: Kevin Hilman <khilman@kernel.org>
Cc: Michele Dionisio <michele.dionisio@gmail.com>
Cc: Frode Isaksen <fisaksen@baylibre.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
We need that to adjust the len of the 2nd transfer (called data in
spi-mem) if it's too long to fit in a SPI message or SPI transfer.
Fixes: c36ff266dc82 ("spi: Extend the core to ease integration of SPI memory controllers")
Cc: <stable@vger.kernel.org>
Signed-off-by: Chuanhua Han <chuanhua.han@nxp.com>
Reviewed-by: Boris Brezillon <boris.brezillon@bootlin.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
There is a logical problem in spi-gpio with host just
assigning a MOSI line and no MISO: this is interpreted
as the host cannot do RX and the host is flagged with
SPI_MASTER_NO_RX.
This is wrong: since GPIO lines can switch direction,
in 3WIRE operation the host will simply reverse the
direction of the GPIO line and start reading from it,
there is even code for doing this in the driver, but
it went unnoticed because it was tested by using a
master with 4 wires but a device using just 3 wires.
Remove the offending flag.
Cc: Andrzej Hajda <a.hajda@samsung.com>
Cc: Lorenzo Bianconi <lorenzo.bianconi@redhat.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
Almost all spi drivers assign spi master->dev.of_node from
its parent platform device without additional refcounting.
It seems of_node_get() in pic32_spi_probe() is unnecessary
and there is no corresponding of_node_put().
Found by Linux Driver Verification project (linuxtesting.org).
Signed-off-by: Alexey Khoroshilov <khoroshilov@ispras.ru>
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
Fixes gcc '-Wunused-but-set-variable' warning:
drivers/spi/spi-pl022.c: In function 'do_polling_transfer':
drivers/spi/spi-pl022.c:1493:20: warning:
variable 'chip' set but not used [-Wunused-but-set-variable]
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
The spi-dw driver currently only supports 8 or 16 bits per word.
Since the hardware supports 4-16 bits per word, adapt the driver
to also support this.
Tested on socfpga cyclone5 with a 9-bit SPI display.
Signed-off-by: Simon Goldschmidt <simon.k.r.goldschmidt@gmail.com>
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
Fixes gcc '-Wunused-but-set-variable' warning:
drivers/spi/spi-gpio.c: In function 'spi_gpio_remove':
drivers/spi/spi-gpio.c:450:33: warning:
variable 'pdata' set but not used [-Wunused-but-set-variable]
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
spi_controller_{suspend,resume}() already prints an error message on
failure, so there is no need to repeat this in individual drivers.
Note: spi_master_{suspend,resume}() is an alias for
spi_controller_{suspend,resume}().
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Reviewed-by: Daniel Mack <daniel@zonque.org>
Acked-by: Nicolas Ferre <nicolas.ferre@microchip.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
- Print spaces as spaces,
- Do not print characters > 126, as they will be shown as garbage
in the modern UTF-8 era,
- Use a normal period instead of its hexadecimal ASCII value,
- Delimit the text part with pipe symbols on both sides (was left side
only), without any spaces, to make it clear where the decoded text
starts and ends,
- Drop a useless comment.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
Document support for the MSIOF module in the Renesas R-Car E3 (r8a77990)
SoC.
No driver update is needed.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
Document support for the MSIOF module in the Renesas R-Car D3 (r8a77995)
SoC.
No driver update is needed.
Signed-off-by: Ulrich Hecht <uli+renesas@fpond.eu>
Reviewed-by: Simon Horman <horms+renesas@verge.net.au>
Reviewed-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
This change increases the source code readability.
Instead of using `spi->child[cs].direct_access.XXX` use `dir_acc->XXX`.
Instead of using `orion_spi->child[cs].direct_access.vaddr` use `vaddr`.
Signed-off-by: Kosta Zertsekel <zertsekel@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Stefan Roese <sr@denx.de>
Reviewed-by: Jan Kundrát <jan.kundrat@cesnet.cz>
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
Define a mask for the IF_SI_OWNER field.
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Acked-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
|
