| Age | Commit message (Collapse) | Author |
|---|
|
The driver uses 802.1Q FIDs when offloading a VLAN-aware bridge.
Unfortunately, it is not possible to assign a VNI to such FIDs, which
prompts the driver to forbid the enslavement of VxLAN devices to a
VLAN-aware bridge.
Workaround this hardware limitation by creating a new family of FIDs,
emulated 802.1Q FIDs. These FIDs are emulated using 802.1D FIDs, which
can be assigned a VNI.
The downside of this approach is that multiple {Port, VID}->FID entries
are required, whereas only a single VID->FID is required with "true"
802.1Q FIDs.
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Reviewed-by: Petr Machata <petrm@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
802.1D FIDs use a per-FID flood table, where the flood index into the
table is calculated by subtracting 4K from the FID's index.
Currently, 802.1D FIDs start at 4K, so the calculation is correct, but
if it was ever to change, the calculation will no longer be correct.
In addition, this change will allow us to reuse the flood index
calculation function in the next patch, where we are going to emulate
802.1Q FIDs using 802.1D FIDs.
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Reviewed-by: Petr Machata <petrm@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
When configuring an FDB entry pointing to a LAG netdev (or its upper),
the driver should only set the 'lag_vid' field when the FID (filtering
identifier) is of 802.1D type.
Extend the 802.1D FID family with an attribute indicating whether this
field should be set and based on its value set the field or leave it
blank.
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Reviewed-by: Petr Machata <petrm@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Fixes gcc '-Wunused-but-set-variable' warning:
drivers/net/ethernet/aquantia/atlantic/hw_atl/hw_atl_utils.c:260:7:
warning: variable 'err' set but not used [-Wunused-but-set-variable]
'err' should be returned while set MPI_DEINIT state fails
in hw_atl_utils_soft_reset.
Fixes: cce96d1883da ("net: aquantia: Regression on reset with 1.x firmware")
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Nikolay Aleksandrov says:
====================
net: bridge: add an option to disabe linklocal learning
This set adds a new bridge option which can control learning from
link-local packets, by default learning is on to be consistent and avoid
breaking users expectations. If the new no_linklocal_learn option is
enabled then the bridge will stop learning from link-local packets.
In order to save space for future boolean options, patch 01 adds a new
bool option API that uses a bitmask to control boolean options. The
bridge is by far the largest netlink attr user and we keep adding simple
boolean options which waste nl attr ids and space. We're not directly
mapping these to the in-kernel bridge flags because some might require
more complex configuration changes (e.g. if we were to add the per port
vlan stats now, it'd require multiple checks before changing value).
Any new bool option needs to be handled by both br_boolopt_toggle and get
in order to be able to retrieve its state later. All such options are
automatically exported via netlink. The behaviour of setting such
options is consistent with netlink option handling when a missing
option is being set (silently ignored), e.g. when a newer iproute2 is used
on older kernel. All supported options are exported via bm's optmask
when dumping the new attribute.
v2: address Andrew Lunn's comments, squash a minor change into patch 01,
export all supported options via optmask when dumping, add patch 03,
pass down extack so options can return meaningful errors, add
WARN_ON on unsupported options (should not happen)
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Now that we have at least one bool option, we can export all of the
supported bool options via optmask when dumping them.
v2: new patch
Signed-off-by: Nikolay Aleksandrov <nikolay@cumulusnetworks.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Use the new boolopt API to add an option which disables learning from
link-local packets. The default is kept as before and learning is
enabled. This is a simple map from a boolopt bit to a bridge private
flag that is tested before learning.
v2: pass NULL for extack via sysfs
Signed-off-by: Nikolay Aleksandrov <nikolay@cumulusnetworks.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
We have been adding many new bridge options, a big number of which are
boolean but still take up netlink attribute ids and waste space in the skb.
Recently we discussed learning from link-local packets[1] and decided
yet another new boolean option will be needed, thus introducing this API
to save some bridge nl space.
The API supports changing the value of multiple boolean options at once
via the br_boolopt_multi struct which has an optmask (which options to
set, bit per opt) and optval (options' new values). Future boolean
options will only be added to the br_boolopt_id enum and then will have
to be handled in br_boolopt_toggle/get. The API will automatically
add the ability to change and export them via netlink, sysfs can use the
single boolopt function versions to do the same. The behaviour with
failing/succeeding is the same as with normal netlink option changing.
If an option requires mapping to internal kernel flag or needs special
configuration to be enabled then it should be handled in
br_boolopt_toggle. It should also be able to retrieve an option's current
state via br_boolopt_get.
v2: WARN_ON() on unsupported option as that shouldn't be possible and
also will help catch people who add new options without handling
them for both set and get. Pass down extack so if an option desires
it could set it on error and be more user-friendly.
[1] https://www.spinics.net/lists/netdev/msg532698.html
Signed-off-by: Nikolay Aleksandrov <nikolay@cumulusnetworks.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Tiwei Bie says:
====================
virtio: support packed ring
This patch set implements packed ring support in virtio driver.
A performance test between pktgen (pktgen_sample03_burst_single_flow.sh)
and DPDK vhost (testpmd/rxonly/vhost-PMD) has been done, I saw
~30% performance gain in packed ring in this case.
To make this patch set work with below patch set for vhost,
some hacks are needed to set the _F_NEXT flag in indirect
descriptors (this should be fixed in vhost):
https://lkml.org/lkml/2018/7/3/33
v2 -> v3:
- Use leXX instead of virtioXX (MST);
- Refactor split ring first (MST);
- Add debug helpers (MST);
- Put split/packed ring specific fields in sub structures (MST);
- Handle normal descriptors and indirect descriptors differently (MST);
- Track the DMA addr/len related info in a separate structure (MST);
- Calculate AVAIL/USED flags only when wrap counter wraps (MST);
- Define a struct/union to read event structure (MST);
- Define a macro for wrap counter bit in uapi (MST);
- Define the AVAIL/USED bits as shifts instead of values (MST);
- s/_F_/_FLAG_/ in VRING_PACKED_EVENT_* as they are values (MST);
- Drop the notify workaround for QEMU's tx-timer in packed ring (MST);
v1 -> v2:
- Use READ_ONCE() to read event off_wrap and flags together (Jason);
- Add comments related to ccw (Jason);
RFC v6 -> v1:
- Avoid extra virtio_wmb() in virtqueue_enable_cb_delayed_packed()
when event idx is off (Jason);
- Fix bufs calculation in virtqueue_enable_cb_delayed_packed() (Jason);
- Test the state of the desc at used_idx instead of last_used_idx
in virtqueue_enable_cb_delayed_packed() (Jason);
- Save wrap counter (as part of queue state) in the return value
of virtqueue_enable_cb_prepare_packed();
- Refine the packed ring definitions in uapi;
- Rebase on the net-next tree;
RFC v5 -> RFC v6:
- Avoid tracking addr/len/flags when DMA API isn't used (MST/Jason);
- Define wrap counter as bool (Jason);
- Use ALIGN() in vring_init_packed() (Jason);
- Avoid using pointer to track `next` in detach_buf_packed() (Jason);
- Add comments for barriers (Jason);
- Don't enable RING_PACKED on ccw for now (noticed by Jason);
- Refine the memory barrier in virtqueue_poll();
- Add a missing memory barrier in virtqueue_enable_cb_delayed_packed();
- Remove the hacks in virtqueue_enable_cb_prepare_packed();
RFC v4 -> RFC v5:
- Save DMA addr, etc in desc state (Jason);
- Track used wrap counter;
RFC v3 -> RFC v4:
- Make ID allocation support out-of-order (Jason);
- Various fixes for EVENT_IDX support;
RFC v2 -> RFC v3:
- Split into small patches (Jason);
- Add helper virtqueue_use_indirect() (Jason);
- Just set id for the last descriptor of a list (Jason);
- Calculate the prev in virtqueue_add_packed() (Jason);
- Fix/improve desc suppression code (Jason/MST);
- Refine the code layout for XXX_split/packed and wrappers (MST);
- Fix the comments and API in uapi (MST);
- Remove the BUG_ON() for indirect (Jason);
- Some other refinements and bug fixes;
RFC v1 -> RFC v2:
- Add indirect descriptor support - compile test only;
- Add event suppression supprt - compile test only;
- Move vring_packed_init() out of uapi (Jason, MST);
- Merge two loops into one in virtqueue_add_packed() (Jason);
- Split vring_unmap_one() for packed ring and split ring (Jason);
- Avoid using '%' operator (Jason);
- Rename free_head -> next_avail_idx (Jason);
- Add comments for virtio_wmb() in virtqueue_add_packed() (Jason);
- Some other refinements and bug fixes;
====================
Acked-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Advertize the packed ring layout support.
Signed-off-by: Tiwei Bie <tiwei.bie@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Currently, ccw, vop and remoteproc need some legacy virtio
APIs to create or access virtio rings, which are not supported
by packed ring. So disable packed ring on these transports
for now.
Signed-off-by: Tiwei Bie <tiwei.bie@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Leverage the EVENT_IDX feature in packed ring to suppress
events when it's available.
Signed-off-by: Tiwei Bie <tiwei.bie@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Introduce the packed ring support. Packed ring can only be
created by vring_create_virtqueue() and each chunk of packed
ring will be allocated individually. Packed ring can not be
created on preallocated memory by vring_new_virtqueue() or
the likes currently.
Signed-off-by: Tiwei Bie <tiwei.bie@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Cache whether we will use DMA API, instead of doing the
check every time. We are going to check whether DMA API
is used more often in packed ring.
Signed-off-by: Tiwei Bie <tiwei.bie@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Introduce a specific function to create the split ring.
And also move the DMA allocation and size information to
the .split sub-structure.
Signed-off-by: Tiwei Bie <tiwei.bie@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Put the split ring's desc state into the .split sub-structure,
and allocate desc state for split ring separately, this makes
the code more readable and more consistent with what we will
do for packed ring.
Signed-off-by: Tiwei Bie <tiwei.bie@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Introduce a helper to check whether we will use indirect
feature. It will be used by packed ring too.
Signed-off-by: Tiwei Bie <tiwei.bie@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Introduce debug helpers for last_add_time update, check and
invalid. They will be used by packed ring too.
Signed-off-by: Tiwei Bie <tiwei.bie@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Put the split ring specific fields in a sub-struct named
as "split" to avoid misuse after introducing packed ring.
There is no functional change.
Signed-off-by: Tiwei Bie <tiwei.bie@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Put the xxx_split() functions together to make the
code more readable and avoid misuse after introducing
the packed ring. There is no functional change.
Signed-off-by: Tiwei Bie <tiwei.bie@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Add _split suffix for split ring specific functions. This
is a preparation for introducing the packed ring support.
There is no functional change.
Signed-off-by: Tiwei Bie <tiwei.bie@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Add types and macros for packed ring.
Signed-off-by: Tiwei Bie <tiwei.bie@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Daniel Borkmann says:
====================
pull-request: bpf-next 2018-11-26
The following pull-request contains BPF updates for your *net-next* tree.
The main changes are:
1) Extend BTF to support function call types and improve the BPF
symbol handling with this info for kallsyms and bpftool program
dump to make debugging easier, from Martin and Yonghong.
2) Optimize LPM lookups by making longest_prefix_match() handle
multiple bytes at a time, from Eric.
3) Adds support for loading and attaching flow dissector BPF progs
from bpftool, from Stanislav.
4) Extend the sk_lookup() helper to be supported from XDP, from Nitin.
5) Enable verifier to support narrow context loads with offset > 0
to adapt to LLVM code generation (currently only offset of 0 was
supported). Add test cases as well, from Andrey.
6) Simplify passing device functions for offloaded BPF progs by
adding callbacks to bpf_prog_offload_ops instead of ndo_bpf.
Also convert nfp and netdevsim to make use of them, from Quentin.
7) Add support for sock_ops based BPF programs to send events to
the perf ring-buffer through perf_event_output helper, from
Sowmini and Daniel.
8) Add read / write support for skb->tstamp from tc BPF and cg BPF
programs to allow for supporting rate-limiting in EDT qdiscs
like fq from BPF side, from Vlad.
9) Extend libbpf API to support map in map types and add test cases
for it as well to BPF kselftests, from Nikita.
10) Account the maximum packet offset accessed by a BPF program in
the verifier and use it for optimizing nfp JIT, from Jiong.
11) Fix error handling regarding kprobe_events in BPF sample loader,
from Daniel T.
12) Add support for queue and stack map type in bpftool, from David.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Make the formatting for map_type_name array consistent.
Signed-off-by: David Calavera <david.calavera@gmail.com>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
|
|
There is a spelling mistake in a btf_verifier_log_member message,
fix it.
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
|
|
Building tags produces warning:
ctags: Warning: kernel/bpf/local_storage.c:10: null expansion of name pattern "\1"
Let's use the same fix as in commit 25528213fe9f ("tags: Fix DEFINE_PER_CPU
expansions"), even though it violates the usual code style.
Signed-off-by: Rustam Kovhaev <rkovhaev@gmail.com>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
|
|
I do not see how one can effectively use skb_insert() without holding
some kind of lock. Otherwise other cpus could have changed the list
right before we have a chance of acquiring list->lock.
Only existing user is in drivers/infiniband/hw/nes/nes_mgt.c and this
one probably meant to use __skb_insert() since it appears nesqp->pau_list
is protected by nesqp->pau_lock. This looks like nesqp->pau_lock
could be removed, since nesqp->pau_list.lock could be used instead.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Cc: Faisal Latif <faisal.latif@intel.com>
Cc: Doug Ledford <dledford@redhat.com>
Cc: Jason Gunthorpe <jgg@ziepe.ca>
Cc: linux-rdma <linux-rdma@vger.kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
A recent change added a null check on p->dev after p->dev was being
dereferenced by the ns_capable check on p->dev. It turns out that
neither the p->dev and p->br null checks are necessary, and can be
removed, which cleans up a static analyis warning.
As Nikolay Aleksandrov noted, these checks can be removed because:
"My reasoning of why it shouldn't be possible:
- On port add new_nbp() sets both p->dev and p->br before creating
kobj/sysfs
- On port del (trickier) del_nbp() calls kobject_del() before call_rcu()
to destroy the port which in turn calls sysfs_remove_dir() which uses
kernfs_remove() which deactivates (shouldn't be able to open new
files) and calls kernfs_drain() to drain current open/mmaped files in
the respective dir before continuing, thus making it impossible to
open a bridge port sysfs file with p->dev and p->br equal to NULL.
So I think it's safe to remove those checks altogether. It'd be nice to
get a second look over my reasoning as I might be missing something in
sysfs/kernfs call path."
Thanks to Nikolay Aleksandrov's suggestion to remove the check and
David Miller for sanity checking this.
Detected by CoverityScan, CID#751490 ("Dereference before null check")
Fixes: a5f3ea54f3cc ("net: bridge: add support for raw sysfs port options")
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Acked-by: Nikolay Aleksandrov <nikolay@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Heiner Kallweit says:
====================
r8169: make use of xmit_more and __netdev_sent_queue
This series adds helper __netdev_sent_queue to the core and makes use
of it in the r8169 driver.
Heiner Kallweit (2):
net: core: add __netdev_sent_queue as variant of __netdev_tx_sent_queue
r8169: make use of xmit_more and __netdev_sent_queue
v2:
- fix minor style issue
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Make use of xmit_more and add the functionality introduced with
3e59020abf0f ("net: bql: add __netdev_tx_sent_queue()").
I used the mlx4 driver as template.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Similar to netdev_sent_queue add helper __netdev_sent_queue as variant
of __netdev_tx_sent_queue.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Packet sockets with PACKET_TX_RING send skbs with user data in frags.
Before commit 5cd8d46ea156 ("packet: copy user buffers before orphan
or clone") ring slots could be released prematurely, possibly allowing
a process to overwrite data still in flight.
This test opens two packet sockets, one to send and one to read.
The sender has a tx ring of one slot. It sends two packets with
different payload, then reads both and verifies their payload.
Before the above commit, both receive calls return the same data as
the send calls use the same buffer. From the commit, the clone
needed for looping onto a packet socket triggers an skb_copy_ubufs
to create a private copy. The separate sends each arrive correctly.
Signed-off-by: Willem de Bruijn <willemb@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Currently dev is dereferenced by the call dev_net(dev) before dev is null
checked. Fix this by null checking dev before the potential null
pointer dereference.
Detected by CoverityScan, CID#1462955 ("Dereference before null check")
Fixes: 23790ef12082 ("net: qualcomm: rmnet: Allow to configure flags for existing devices")
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Fixes gcc '-Wunused-but-set-variable' warning:
drivers/net/ethernet/chelsio/cxgb4/t4_hw.c:5883:6:
warning: variable 'multitrc' set but not used [-Wunused-but-set-variable]
drivers/net/ethernet/chelsio/cxgb4/t4_hw.c:8585:32:
warning: variable 'speed' set but not used [-Wunused-but-set-variable]
'multitrc' never used since introduction in
commit 8e3d04fd7d70 ("cxgb4: Add MPS tracing support")
'speed' never used since introduction in
commit c3168cabe1af ("cxgb4/cxgbvf: Handle 32-bit fw port capabilities")
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Return code should be formally "netdev_tx_t".
Signed-off-by: Alexey Dobriyan <adobriyan@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/arm64/linux
Pull arm64 fixes from Catalin Marinas::
- Fix wrong conflict resolution around CONFIG_ARM64_SSBD
- Fix sparse warning on unsigned long constant
* tag 'arm64-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/arm64/linux:
arm64: cpufeature: Fix mismerge of CONFIG_ARM64_SSBD block
arm64: sysreg: fix sparse warnings
|
|
Pull networking fixes from David Miller:
1) Need to take mutex in ath9k_add_interface(), from Dan Carpenter.
2) Fix mt76 build without CONFIG_LEDS_CLASS, from Arnd Bergmann.
3) Fix socket wmem accounting in SCTP, from Xin Long.
4) Fix failed resume crash in ena driver, from Arthur Kiyanovski.
5) qed driver passes bytes instead of bits into second arg of
bitmap_weight(). From Denis Bolotin.
6) Fix reset deadlock in ibmvnic, from Juliet Kim.
7) skb_scrube_packet() needs to scrub the fwd marks too, from Petr
Machata.
8) Make sure older TCP stacks see enough dup ACKs, and avoid doing SACK
compression during this period, from Eric Dumazet.
9) Add atomicity to SMC protocol cursor handling, from Ursula Braun.
10) Don't leave dangling error pointer if bpf_prog_add() fails in
thunderx driver, from Lorenzo Bianconi. Also, when we unmap TSO
headers, set sq->tso_hdrs to NULL.
11) Fix race condition over state variables in act_police, from Davide
Caratti.
12) Disable guest csum in the presence of XDP in virtio_net, from Jason
Wang.
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net: (64 commits)
net: gemini: Fix copy/paste error
net: phy: mscc: fix deadlock in vsc85xx_default_config
dt-bindings: dsa: Fix typo in "probed"
net: thunderx: set tso_hdrs pointer to NULL in nicvf_free_snd_queue
net: amd: add missing of_node_put()
team: no need to do team_notify_peers or team_mcast_rejoin when disabling port
virtio-net: fail XDP set if guest csum is negotiated
virtio-net: disable guest csum during XDP set
net/sched: act_police: add missing spinlock initialization
net: don't keep lonely packets forever in the gro hash
net/ipv6: re-do dad when interface has IFF_NOARP flag change
packet: copy user buffers before orphan or clone
ibmvnic: Update driver queues after change in ring size support
ibmvnic: Fix RX queue buffer cleanup
net: thunderx: set xdp_prog to NULL if bpf_prog_add fails
net/dim: Update DIM start sample after each DIM iteration
net: faraday: ftmac100: remove netif_running(netdev) check before disabling interrupts
net/smc: use after free fix in smc_wr_tx_put_slot()
net/smc: atomic SMCD cursor handling
net/smc: add SMC-D shutdown signal
...
|
|
Pull xfs fixes from Darrick Wong:
"Dave and I have continued our work fixing corruption problems that can
be found when running long-term burn-in exercisers on xfs. Here are
some patches fixing most of the problems, but there will likely be
more. :/
- Numerous corruption fixes for copy on write
- Numerous corruption fixes for blocksize < pagesize writes
- Don't miscalculate AG reservations for small final AGs
- Fix page cache truncation to work properly for reflink and extent
shifting
- Fix use-after-free when retrying failed inode/dquot buffer logging
- Fix corruptions seen when using copy_file_range in directio mode"
* tag 'xfs-4.20-fixes-2' of git://git.kernel.org/pub/scm/fs/xfs/xfs-linux:
iomap: readpages doesn't zero page tail beyond EOF
vfs: vfs_dedupe_file_range() doesn't return EOPNOTSUPP
iomap: dio data corruption and spurious errors when pipes fill
iomap: sub-block dio needs to zeroout beyond EOF
iomap: FUA is wrong for DIO O_DSYNC writes into unwritten extents
xfs: delalloc -> unwritten COW fork allocation can go wrong
xfs: flush removing page cache in xfs_reflink_remap_prep
xfs: extent shifting doesn't fully invalidate page cache
xfs: finobt AG reserves don't consider last AG can be a runt
xfs: fix transient reference count error in xfs_buf_resubmit_failed_buffers
xfs: uncached buffer tracing needs to print bno
xfs: make xfs_file_remap_range() static
xfs: fix shared extent data corruption due to missing cow reservation
|
|
The TX stats should be started with the tx_stats_syncp,
there seems to be a copy/paste error in the driver.
Signed-off-by: Andreas Fiedler <andreas.fiedler@gmx.net>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The vsc85xx_default_config function called in the vsc85xx_config_init
function which is used by VSC8530, VSC8531, VSC8540 and VSC8541 PHYs
mistakenly calls phy_read and phy_write in-between phy_select_page and
phy_restore_page.
phy_select_page and phy_restore_page actually take and release the MDIO
bus lock and phy_write and phy_read take and release the lock to write
or read to a PHY register.
Let's fix this deadlock by using phy_modify_paged which handles
correctly a read followed by a write in a non-standard page.
Fixes: 6a0bfbbe20b0 ("net: phy: mscc: migrate to phy_select/restore_page functions")
Signed-off-by: Quentin Schulz <quentin.schulz@bootlin.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The correct form is "can be probed", so fix the typo.
Signed-off-by: Fabio Estevam <festevam@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Reset snd_queue tso_hdrs pointer to NULL in nicvf_free_snd_queue routine
since it is used to check if tso dma descriptor queue has been previously
allocated. The issue can be triggered with the following reproducer:
$ip link set dev enP2p1s0v0 xdpdrv obj xdp_dummy.o
$ip link set dev enP2p1s0v0 xdpdrv off
[ 341.467649] WARNING: CPU: 74 PID: 2158 at mm/vmalloc.c:1511 __vunmap+0x98/0xe0
[ 341.515010] Hardware name: GIGABYTE H270-T70/MT70-HD0, BIOS T49 02/02/2018
[ 341.521874] pstate: 60400005 (nZCv daif +PAN -UAO)
[ 341.526654] pc : __vunmap+0x98/0xe0
[ 341.530132] lr : __vunmap+0x98/0xe0
[ 341.533609] sp : ffff00001c5db860
[ 341.536913] x29: ffff00001c5db860 x28: 0000000000020000
[ 341.542214] x27: ffff810feb5090b0 x26: ffff000017e57000
[ 341.547515] x25: 0000000000000000 x24: 00000000fbd00000
[ 341.552816] x23: 0000000000000000 x22: ffff810feb5090b0
[ 341.558117] x21: 0000000000000000 x20: 0000000000000000
[ 341.563418] x19: ffff000017e57000 x18: 0000000000000000
[ 341.568719] x17: 0000000000000000 x16: 0000000000000000
[ 341.574020] x15: 0000000000000010 x14: ffffffffffffffff
[ 341.579321] x13: ffff00008985eb27 x12: ffff00000985eb2f
[ 341.584622] x11: ffff0000096b3000 x10: ffff00001c5db510
[ 341.589923] x9 : 00000000ffffffd0 x8 : ffff0000086868e8
[ 341.595224] x7 : 3430303030303030 x6 : 00000000000006ef
[ 341.600525] x5 : 00000000003fffff x4 : 0000000000000000
[ 341.605825] x3 : 0000000000000000 x2 : ffffffffffffffff
[ 341.611126] x1 : ffff0000096b3728 x0 : 0000000000000038
[ 341.616428] Call trace:
[ 341.618866] __vunmap+0x98/0xe0
[ 341.621997] vunmap+0x3c/0x50
[ 341.624961] arch_dma_free+0x68/0xa0
[ 341.628534] dma_direct_free+0x50/0x80
[ 341.632285] nicvf_free_resources+0x160/0x2d8 [nicvf]
[ 341.637327] nicvf_config_data_transfer+0x174/0x5e8 [nicvf]
[ 341.642890] nicvf_stop+0x298/0x340 [nicvf]
[ 341.647066] __dev_close_many+0x9c/0x108
[ 341.650977] dev_close_many+0xa4/0x158
[ 341.654720] rollback_registered_many+0x140/0x530
[ 341.659414] rollback_registered+0x54/0x80
[ 341.663499] unregister_netdevice_queue+0x9c/0xe8
[ 341.668192] unregister_netdev+0x28/0x38
[ 341.672106] nicvf_remove+0xa4/0xa8 [nicvf]
[ 341.676280] nicvf_shutdown+0x20/0x30 [nicvf]
[ 341.680630] pci_device_shutdown+0x44/0x88
[ 341.684720] device_shutdown+0x144/0x250
[ 341.688640] kernel_restart_prepare+0x44/0x50
[ 341.692986] kernel_restart+0x20/0x68
[ 341.696638] __se_sys_reboot+0x210/0x238
[ 341.700550] __arm64_sys_reboot+0x24/0x30
[ 341.704555] el0_svc_handler+0x94/0x110
[ 341.708382] el0_svc+0x8/0xc
[ 341.711252] ---[ end trace 3f4019c8439959c9 ]---
[ 341.715874] page:ffff7e0003ef4000 count:0 mapcount:0 mapping:0000000000000000 index:0x4
[ 341.723872] flags: 0x1fffe000000000()
[ 341.727527] raw: 001fffe000000000 ffff7e0003f1a008 ffff7e0003ef4048 0000000000000000
[ 341.735263] raw: 0000000000000004 0000000000000000 00000000ffffffff 0000000000000000
[ 341.742994] page dumped because: VM_BUG_ON_PAGE(page_ref_count(page) == 0)
where xdp_dummy.c is a simple bpf program that forwards the incoming
frames to the network stack (available here:
https://github.com/altoor/xdp_walkthrough_examples/blob/master/sample_1/xdp_dummy.c)
Fixes: 05c773f52b96 ("net: thunderx: Add basic XDP support")
Fixes: 4863dea3fab0 ("net: Adding support for Cavium ThunderX network controller")
Signed-off-by: Lorenzo Bianconi <lorenzo.bianconi@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Fix smatch warning:
drivers/ptp/ptp_clock.c:298 ptp_clock_register() warn:
passing zero to 'ERR_PTR'
'err' should be set while device_create_with_groups and
pps_register_source fails
Fixes: 85a66e550195 ("ptp: create "pins" together with the rest of attributes")
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Acked-by: Richard Cochran <richardcochran@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Petr Machata says:
====================
switchdev: Convert switchdev_port_obj_{add,del}() to notifiers
An offloading driver may need to have access to switchdev events on
ports that aren't directly under its control. An example is a VXLAN port
attached to a bridge offloaded by a driver. The driver needs to know
about VLANs configured on the VXLAN device. However the VXLAN device
isn't stashed between the bridge and a front-panel-port device (such as
is the case e.g. for LAG devices), so the usual switchdev ops don't
reach the driver.
VXLAN is likely not the only device type like this: in theory any L2
tunnel device that needs offloading will prompt requirement of this
sort.
A way to fix this is to give up the notion of port object addition /
deletion as a switchdev operation, which assumes somewhat tight coupling
between the message producer and consumer. And instead send the message
over a notifier chain.
The series starts with a clean-up patch #1, where
SWITCHDEV_OBJ_PORT_{VLAN, MDB}() are fixed up to lift the constraint
that the passed-in argument be a simple variable named "obj".
switchdev_port_obj_add and _del are invoked in a context that permits
blocking. Not only that, at least for the VLAN notification, being able
to signal failure is actually important. Therefore introduce a new
blocking notifier chain that the new events will be sent on. That's done
in patch #2. Retain the current (atomic) notifier chain for the
preexisting notifications.
In patch #3, introduce two new switchdev notifier types,
SWITCHDEV_PORT_OBJ_ADD and SWITCHDEV_PORT_OBJ_DEL. These notifier types
communicate the same event as the corresponding switchdev op, except in
a form of a notification. struct switchdev_notifier_port_obj_info was
added to carry the fields that correspond to the switchdev op arguments.
An additional field, handled, will be used to communicate back to
switchdev that the event has reached an interested party, which will be
important for the two-phase commit.
In patches #4, #5, and #7, rocker, DSA resp. ethsw are updated to
subscribe to the switchdev blocking notifier chain, and handle the new
notifier types. #6 introduces a helper to determine whether a
netdevice corresponds to a front panel port.
What these three drivers have in common is that their ports don't
support any uppers besides bridge. That makes it possible to ignore any
notifiers that don't reference a front-panel port device, because they
are certainly out of scope.
Unlike the previous three, mlxsw and ocelot drivers admit stacked
devices as uppers. While the current switchdev code recursively descends
through layers of lower devices, eventually calling the op on a
front-panel port device, the notifier would reference a stacking device
that's one of front-panel ports uppers. The filtering is thus more
complex.
For ocelot, such iteration is currently pretty much required, because
there's no bookkeeping of LAG devices. mlxsw does keep the list of LAGs,
however it iterates the lower devices anyway when deciding whether an
event on a tunnel device pertains to the driver or not.
Therefore this patch set instead introduces, in patch #8, a helper to
iterate through lowers, much like the current switchdev code does,
looking for devices that match a given predicate.
Then in patches #9 and #10, first mlxsw and then ocelot are updated to
dispatch the newly-added notifier types to the preexisting
port_obj_add/_del handlers. The dispatch is done via the new helper, to
recursively descend through lower devices.
Finally in patch #11, the actual switch is made, retiring the current
SDO-based code in favor of a notifier.
Now that the event is distributed through a notifier, the explicit
netdevice check in rocker, DSA and ethsw doesn't let through any events
except those done on a front-panel port itself. It is therefore
unnecessary to check in VLAN-handling code whether a VLAN was added to
the bridge itself: such events will simply be ignored much sooner.
Therefore remove it in patch #12.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Due to an explicit check in rocker_world_port_obj_vlan_add(),
dsa_slave_switchdev_event() resp. port_switchdev_event(), VLAN objects
that are added to a device that is not a front-panel port device are
ignored. Therefore this check is immaterial.
Signed-off-by: Petr Machata <petrm@mellanox.com>
Acked-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Drop switchdev_ops.switchdev_port_obj_add and _del. Drop the uses of
this field from all clients, which were migrated to use switchdev
notification in the previous patches.
Add a new function switchdev_port_obj_notify() that sends the switchdev
notifications SWITCHDEV_PORT_OBJ_ADD and _DEL.
Update switchdev_port_obj_del_now() to dispatch to this new function.
Drop __switchdev_port_obj_add() and update switchdev_port_obj_add()
likewise.
Signed-off-by: Petr Machata <petrm@mellanox.com>
Reviewed-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Following patches will change the way of distributing port object
changes from a switchdev operation to a switchdev notifier. The
switchdev code currently recursively descends through layers of lower
devices, eventually calling the op on a front-panel port device. The
notifier will instead be sent referencing the bridge port device, which
may be a stacking device that's one of front-panel ports uppers, or a
completely unrelated device.
Dispatch the new events to ocelot_port_obj_add() resp. _del() to
maintain the same behavior that the switchdev operation based code
currently has. Pass through switchdev_handle_port_obj_add() / _del() to
handle the recursive descend, because Ocelot supports LAG uppers.
Register to the new switchdev blocking notifier chain to get the new
events when they start getting distributed.
Signed-off-by: Petr Machata <petrm@mellanox.com>
Acked-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Following patches will change the way of distributing port object
changes from a switchdev operation to a switchdev notifier. The
switchdev code currently recursively descends through layers of lower
devices, eventually calling the op on a front-panel port device. The
notifier will instead be sent referencing the bridge port device, which
may be a stacking device that's one of front-panel ports uppers, or a
completely unrelated device.
To handle SWITCHDEV_PORT_OBJ_ADD and _DEL, subscribe to the blocking
notifier chain. Dispatch to mlxsw_sp_port_obj_add() resp. _del() to
maintain the behavior that the switchdev operation based code currently
has. Defer to switchdev_handle_port_obj_add() / _del() to handle the
recursive descend, because mlxsw supports a number of upper types.
Signed-off-by: Petr Machata <petrm@mellanox.com>
Reviewed-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
After the transition from switchdev operations to notifier chain (which
will take place in following patches), the onus is on the driver to find
its own devices below possible layer of LAG or other uppers.
The logic to do so is fairly repetitive: each driver is looking for its
own devices among the lowers of the notified device. For those that it
finds, it calls a handler. To indicate that the event was handled,
struct switchdev_notifier_port_obj_info.handled is set. The differences
lie only in what constitutes an "own" device and what handler to call.
Therefore abstract this logic into two helpers,
switchdev_handle_port_obj_add() and switchdev_handle_port_obj_del(). If
a driver only supports physical ports under a bridge device, it will
simply avoid this layer of indirection.
One area where this helper diverges from the current switchdev behavior
is the case of mixed lowers, some of which are switchdev ports and some
of which are not. Previously, such scenario would fail with -EOPNOTSUPP.
The helper could do that for lowers for which the passed-in predicate
doesn't hold. That would however break the case that switchdev ports
from several different drivers are stashed under one master, a scenario
that switchdev currently happily supports. Therefore tolerate any and
all unknown netdevices, whether they are backed by a switchdev driver
or not.
Signed-off-by: Petr Machata <petrm@mellanox.com>
Reviewed-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
