summaryrefslogtreecommitdiff
AgeCommit message (Collapse)Author
2010-05-14mtd: nand: support alternate BB marker locations on MLCKevin Cernekee
This is a slightly modified version of a patch submitted last year by Reuben Dowle <reuben.dowle@navico.com>. His original comments follow: This patch adds support for some MLC NAND flashes that place the BB marker in the LAST page of the bad block rather than the FIRST page used for SLC NAND and other types of MLC nand. Lifted from Samsung datasheet for K9LG8G08U0A (1Gbyte MLC NAND): " Identifying Initial Invalid Block(s) All device locations are erased(FFh) except locations where the initial invalid block(s) information is written prior to shipping. The initial invalid block(s) status is defined by the 1st byte in the spare area. Samsung makes sure that the last page of every initial invalid block has non-FFh data at the column address of 2,048. ... " As far as I can tell, this is the same for all Samsung MLC nand, and in fact the samsung bsp for the processor used in our project (s3c6410) actually contained a hack similar to this patch but less portable to enable use of their NAND parts. I discovered this problem when trying to use a Micron NAND which does not used this layout - I wish samsung would put their stuff in main-line to avoid this type of problem. Currently this patch causes all MLC nand with manufacturer codes from Samsung and ST(Numonyx) to use this alternative location, since these are the manufactures that I know of that use this layout. Signed-off-by: Kevin Cernekee <cernekee@gmail.com> Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
2010-05-14mtd: nand: extend NAND flash detection to new MLC chipsKevin Cernekee
Some of the newer MLC devices have a 6-byte ID sequence in which several field definitions differ from older chips in a manner that is not backward compatible. For instance: Samsung K9GAG08U0M (5-byte sequence): ec d5 14 b6 74 4th byte, bits 1:0 encode the page size: 0=1KiB, 1=2KiB, 2=4KiB, 3=8KiB 4th byte, bits 5:4 encode the block size: 0=64KiB, 1=128KiB, ... 4th byte, bit 6 encodes the OOB size: 0=8B/512B, 1=16B/512B Samsung K9GAG08U0D (6-byte sequence): ec d5 94 29 34 41 4th byte, bits 1:0 encode the page size: 0=2KiB, 1=4KiB, 3=8KiB, 4=rsvd 4th byte, bits 7;5:4 encode the block size: 0=128KiB, 1=256KiB, ... 4th byte, bits 6;3:2 encode the OOB size: 1=128B/page, 2=218B/page This patch uses the new 6-byte scheme if the following conditions are all true: 1) The ID code wraps around after exactly 6 bytes 2) Manufacturer is Samsung 3) 6th byte is zero The patch also extends the maximum OOB size from 128B to 256B. Signed-off-by: Kevin Cernekee <cernekee@gmail.com> Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
2010-05-14mtd: suppress warnings in inline_map_read()Kevin Cernekee
With gcc 4.4.3 -O2 on MIPS32: drivers/mtd/chips/cfi_util.c: In function 'cfi_qry_present': include/linux/mtd/map.h:390: warning: 'r' may be used uninitialized in this function include/linux/mtd/map.h:375: note: 'r' was declared here include/linux/mtd/map.h:390: warning: 'r' may be used uninitialized in this function include/linux/mtd/map.h:375: note: 'r' was declared here Signed-off-by: Kevin Cernekee <cernekee@gmail.com> Signed-off-by: Artem Bityutskiy <Artem.Bityutskiy@nokia.com> Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
2010-05-14mtd: map.h: add missing bug.h includeKevin Cernekee
Signed-off-by: Kevin Cernekee <cernekee@gmail.com> Signed-off-by: Artem Bityutskiy <Artem.Bityutskiy@nokia.com> Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
2010-05-14mtd: sst25l: fix multi-part messages with broken spi mastersH Hartley Sweeten
Some SPI masters (ep93xx) have limitations when using the SFRMOUT signal for the spi device chip select. The SFRMOUT signal is only asserted as long as the spi transmit fifo contains data. As soon as the last bit is clocked into the receive fifo it gets deasserted. The functions sst25l_status and sst25l_match_device use the API function spi_write_then_read to write a command to the flash then read the response back. This API function creates a two part spi message for the write then read. When this message is transferred the SFRMOUT signal ends up getting deasserted after the command phase. This causes the command to get aborted by the device so the read phase returns invalid data. By changing sst25l_status and sst25l_match_device to use a single transfer synchronous message, the SFRMOUT signal stays asserted during the entire message so the correct data always gets returned. This change will have no effect on SPI masters which use a chip select mechanism (GPIO's, etc.) which does stay asserted correctly. As a bonus, the single transfer synchronous messages complete faster than multi-part messages. Signed-off-by: H Hartley Sweeten <hsweeten@visionengravers.com> Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
2010-05-14mtd: add Samsung SoC OneNAND driverKyungmin Park
This patch adds a driver for OneNAND controller on Samsung SoCs. Following SoCs are supported: S3C6400, S3C6410, S5PC100 and S5PC110. Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com> Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com> Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
2010-05-14mtd: onenand: add workaround for SYNC_WRITE modeKyungmin Park
Some chips fails to identify properly when SYNC_WRITE mode is enabled (the example is OneNAND on S5PC110 SoC). This patch adds a workaround for such chips. Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com> Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com> Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
2010-05-14mtd: onenand: add new callback for bufferram readKyungmin Park
This patch adds a new callback for the underlying drivers, which is called instead of accessing the buffer ram directly. This callback will be used by Samsung OneNAND driver to implement DMA transfers on S5PC110 SoC. Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com> Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com> Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
2010-05-14mtd: onenand: allocate verify buffer in the coreKyungmin Park
This patch extends OneNAND core code with support for OneNAND verify write check. This is done by allocating the buffer for verify read directly from the core code. Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com> Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com> Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
2010-05-14mtd: onenand: add support for chips with 4KiB page sizeKyungmin Park
This patch adds support for OneNAND chips that have 4KiB page size. Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com> Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com> Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
2010-05-14mtd: jedec_probe: remove spaces before tabsArtem Bityutskiy
Nothing very important, this just makes git am stop producing warnings. Signed-off-by: Artem Bityutskiy <Artem.Bityutskiy@nokia.com> Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
2010-05-14mtd: chips: use common manufacturer codes in jedec_probe()Wolfram Sang
Factor out old manufacturers and use the generic ones from cfi.h Signed-off-by: Wolfram Sang <w.sang@pengutronix.de> Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
2010-05-14mtd: cfi_util: do not printk if no extended query tableGuillaume LECERF
Signed-off-by: Guillaume LECERF <glecerf@gmail.com> Reviewed-by: Wolfram Sang <w.sang@pengutronix.de> Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
2010-05-14mtd: cfi_cmdset_0002: add CFI detection for SST 39VF{32, 64}xxB chipsGuillaume LECERF
This patch adds support for detecting SST 39VF32xxB and 39VF64xxB chips in CFI mode. Signed-off-by: Guillaume LECERF <glecerf@gmail.com> Reviewed-by: Wolfram Sang <w.sang@pengutronix.de> Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
2010-05-14mtd: cfi_cmdset_0002: add CFI detection for SST 39VF{16, 32}xx chipsGuillaume LECERF
SST 39VF{16,32}xx chips use the 0x0701 command set, fully compatible with the AMD one. This patch adds support for detecting them in CFI mode. Signed-off-by: Guillaume LECERF <glecerf@gmail.com> Reviewed-by: Wolfram Sang <w.sang@pengutronix.de> Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
2010-05-14mtd: cfi_cmdset_0002: Tone down warning messages about TopBottom CFI fieldDavid Woodhouse
Accept values of 2-5 for TopBottom, where the newly-added 4 and 5 values mean a uniform layout. It does indicate WP layout but we don't handle that. Also don't say "broken" when swapping erase regions in a top-boot chip. That got retrospectively documented in the spec. Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
2010-05-14mtd: cfi_cmdset_0002: do not fail on no extended query table as they are ↵Guillaume LECERF
both optional After looking at AMD's CFI specification [1], both of the extended query tables are optional. Thus, it looks like relying that at least one of those tables exist is a bug in cfi_cmdset_0002. This patch inverts the logic and checks for unlock function pointers before exiting on error. This approach leaves place to add a call to a fixup function to try to handle chips compatible with the early AMD specification from 1995 [2]. [1] http://www.amd.com/us-en/assets/content_type/DownloadableAssets/cfi_r20.pdf [2] http://noel.feld.cvut.cz/hw/amd/20158a.pdf Signed-off-by: Guillaume LECERF <glecerf@gmail.com> Reviewed-by: Wolfram Sang <w.sang@pengutronix.de> Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
2010-05-14mtd: cfi_probe: use P_ID_* definitions instead of hardcoded valuesGuillaume LECERF
Use P_ID_* definitions already in include/linux/mtd/cfi.h instead of the hardcoded values. Make the code more readable. Signed-off-by: Guillaume LECERF <glecerf@gmail.com> Reviewed-by: Wolfram Sang <w.sang@pengutronix.de> Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
2010-05-14mtd: cfi_probe: add support for SST 0x0701 vendornameGuillaume LECERF
SST 39VF160x and 39VF320x chips use vendorname id 0x0701 and alternative unlock addresses. Add support for them in cfi_probe.c. Signed-off-by: Guillaume LECERF <glecerf@gmail.com> Reviewed-by: Wolfram Sang <w.sang@pengutronix.de> Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
2010-05-14mtd: cfi_probe: make the addresses used to enter Auto Select Mode variableGuillaume LECERF
Make the addresses used to enter Auto Select Mode variable to leave place for handling chips using non-standard addresses. Signed-off-by: Guillaume LECERF <glecerf@gmail.com> Reviewed-by: Wolfram Sang <w.sang@pengutronix.de> Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
2010-05-14mtd: cfi_probe: enter Auto Select Mode after filling cfi->cfiq membersGuillaume LECERF
Move the code to enter Auto Select Mode down to be able to use cfi->cfiq members to add support for chips using alternative sequence / unlock addresses. Signed-off-by: Guillaume LECERF <glecerf@gmail.com> Reviewed-by: Wolfram Sang <w.sang@pengutronix.de> Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
2010-05-14mtd: kirkwood: allow machines to register RnB callbackBen Dooks
Add a kirkwood_nand_init_rnb() call to allow boards which have RnB line detection to register this instead of a static delay. Signed-off-by: Ben Dooks <ben@simtec.co.uk> Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
2010-05-14mtd: orion/kirkwood: add RnB line support to orion mtd driverBen Dooks
Add support for a board to register a callback to get the state of the RnB line if it has it attached. Signed-off-by: Ben Dooks <ben@simtec.co.uk> Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
2010-05-14mtd: sm_common: split smartmedia and xD tableMaxim Levitsky
2GB xD card, and 4MB SmartMedia ROM card share same ID, so to make both work split xD and smartmedia ID tables. Hardware driver must be able to know which type it handles (and probably just one). Signed-off-by: Maxim Levitsky <maximlevitsky@gmail.com> Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
2010-05-14mtd: mxc_nand: support i.MX21Ivo Clarysse
On i.MX21 SoCs, if the NFC_CONFIG1:NFC_INT_MASK bit is set, NFC_CONFIG2:NFC_INT always reads out zero, even if an operation is completed. This patch uses enable_irq and disable_irq_nosync instead of NFC_CONFIG1:NFC_INT_MASK to mask NFC interrupts. This allows NFC_CONFIG2:NFC_INT to also be used to detect operation completion on i.MX21. The i.MX21 NFC does not signal reset completion using NFC_CONFIG1:NFC_INT_MASK, so instead reset completion is tested by checking if NFC_CONFIG2 becomes 0. Signed-off-by: Ivo Clarysse <ivo.clarysse@gmail.com> Acked-by: Sascha Hauer <s.hauer@pengutronix.de> Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
2010-05-14mtd: mxc_nand: set NFC registers after resetIvo Clarysse
This patch allows the mxc_nand driver to reset the NAND flash controller. NFC registers are (re-)set after completion of the reset, as a reset will have reverted the NFC registers to their default values. Signed-off-by: Ivo Clarysse <ivo.clarysse@gmail.com> Acked-by: Sascha Hauer <s.hauer@pengutronix.de> Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
2010-05-14mtd: extend physmap_of to let the device tree specify the parition probeJason Gunthorpe
This is to support custom partitioning schemes for embedded PPC. To use define your own mtd_part_parser and then add something like: linux,part-probe = "my_probe", "cmdlinepart"; To the board's dts file. If linux,part-probe is not specified then this behaves the same as before. Signed-off-by: Jason Gunthorpe <jgunthorpe@obsidianresearch.com> Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
2010-05-13drivers/mtd: Use kzallocJulia Lawall
Use kzalloc rather than the combination of kmalloc and memset. The semantic patch that makes this change is as follows: (http://coccinelle.lip6.fr/) // <smpl> @@ expression x,size,flags; statement S; @@ -x = kmalloc(size,flags); +x = kzalloc(size,flags); if (x == NULL) S -memset(x, 0, size); // </smpl> Signed-off-by: Julia Lawall <julia@diku.dk> Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
2010-05-13drivers/mtd/nand: Use kzallocJulia Lawall
Use kzalloc rather than the combination of kmalloc and memset. The semantic patch that makes this change is as follows: (http://coccinelle.lip6.fr/) // <smpl> @@ expression x,size,flags; statement S; @@ -x = kmalloc(size,flags); +x = kzalloc(size,flags); if (x == NULL) S -memset(x, 0, size); // </smpl> Signed-off-by: Julia Lawall <julia@diku.dk> Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
2010-05-13mtd/nand: Fix denali build on ppc64David Woodhouse
drivers/mtd/nand/denali.c:1427: error: conflicting types for ‘enable_dma’ arch/powerpc/include/asm/dma.h:189: note: previous definition of ‘enable_dma’ was here Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
2010-05-13mtd/nand: Add Intel Moorestown/Denali NAND supportJason Roberts
There is more work to be done on this but it is basically working now. Signed-off-by: Jason Roberts <jason.e.roberts@intel.com> Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
2010-05-12mtd/nand/sh_flctl: Move function mtd_to_flctl to fix build failurePeter Huewe
This patch fixes a build failure[1] by simply moving the function mtd_to_flctl beneath the definition of sh_flctl which it uses. BF introduced by patch 'mtd/nand/sh_flctl: Replace the dangerous mtd_to_flctl macro' (67026418) Signed-off-by: Peter Huewe <peterhuewe@gmx.de> Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
2010-05-10Merge branch 'master' of ↵David Woodhouse
git://git.kernel.org/pub/scm/linux/kernel/git/torvalds/linux-2.6 Conflicts: drivers/mtd/mtdcore.c Pull in the bdi fixes and ARM platform changes that other outstanding patches depend on.
2010-05-10mtd: mpc5121_nfc: Changed SVR check to allow MPC5123.Steve Deiters
The revision in SVR for MPC5123 is 3. The NFC is the same as MPC5121 revision 2. Signed-off-by: Steve Deiters <SteveDeiters@basler.com> Signed-off-by: Artem Bityutskiy <Artem.Bityutskiy@nokia.com> Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
2010-05-10mtd: sst25l: remove unnecessary MTD_DEBUG_LEVEL2 messagesH Hartley Sweeten
All the SST25L series flash parts have uniform erase sectors. Remove the extra MTD_DEBUG_LEVEL2 messages showing the eraseregions info since they could never be shown. Signed-off-by: H Hartley Sweeten <hsweeten@visionengravers.com> Signed-off-by: Artem Bityutskiy <Artem.Bityutskiy@nokia.com> Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
2010-05-10mtd: cfi_cmdset_0002: Add reboot notifier for AMD flashesKevin Cernekee
Ensure that the flash device is in a quiescent state before rebooting. The implementation is closely modeled after the cfi_cmdset_0001 reboot notifier, commit 963a6fb0a0d336d0513083b7e4b5c3ff9d6d2061 . Signed-off-by: Kevin Cernekee <cernekee@gmail.com> Signed-off-by: Artem Bityutskiy <Artem.Bityutskiy@nokia.com> Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
2010-05-10mtd: pxa32xx_nand: add support for partition table parsingMarc Kleine-Budde
The pxa32xx_nand driver doesn't support partition tables from the command line. This patch adds support for it. Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de> Signed-off-by: Artem Bityutskiy <Artem.Bityutskiy@nokia.com> Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
2010-05-10mtd/nand/bcm_umi: remove unused #include <linux/version.h>Huang Weiyi
Remove unused #include <linux/version.h>('s) in drivers/mtd/nand/bcm_umi_nand.c Signed-off-by: Huang Weiyi <weiyi.huang@gmail.com> Acked-by: Leo Chen <leochen@broadcom.com> Signed-off-by: Artem Bityutskiy <Artem.Bityutskiy@nokia.com> Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
2010-05-10mtd: maps: Eliminate use after freeJulia Lawall
Moved the debugging message before the call to map_destroy, which frees its argument. The message is also slightly changed to reflect its new position. A simplified version of the semantic patch that finds this problem is as follows: (http://coccinelle.lip6.fr/) // <smpl> @@ expression E,E2; @@ del_mtd_device(E) ... ( E = E2 | * E ) // </smpl> Signed-off-by: Julia Lawall <julia@diku.dk> Signed-off-by: Artem Bityutskiy <Artem.Bityutskiy@nokia.com> Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
2010-05-10mtd: fix a huge latency problem in the MTD CFI and LPDDR flash drivers.Stefani Seibold
The use of a memcpy() during a spinlock operation will cause very long thread context switch delays if the flash chip bandwidth is low and the data to be copied large, because a spinlock will disable preemption. For example: A flash with 6,5 MB/s bandwidth will cause under ubifs, which request sometimes 128 KiB (the flash erase size), a preemption delay of 20 milliseconds. High priority threads will not be served during this time, regardless whether this threads access the flash or not. This behavior breaks real time. The patch changes all the use of spin_lock operations for xxxx->mutex into mutex operations, which is exact what the name says and means. I have checked the code of the drivers and there is no use of atomic pathes like interrupt or timers. The mtdoops facility will also not be used by this drivers. So it is dave to replace the spin_lock against mutex. There is no performance regression since the mutex is normally not acquired. Changelog: 06.03.2010 First release 26.03.2010 Fix mutex[1] issue and tested it for compile failure Signed-off-by: Stefani Seibold <stefani@seibold.net> Signed-off-by: Artem Bityutskiy <Artem.Bityutskiy@nokia.com> Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
2010-05-10mtd/nand/sh_flctl: Replace the dangerous mtd_to_flctl macroFerenc Wagner
The original macro worked only when applied to variables named 'mtd'. While this could have been fixed by simply renaming the macro argument, a more type-safe replacement is preferred. Signed-off-by: Ferenc Wagner <wferi@niif.hu> Signed-off-by: Artem Bityutskiy <Artem.Bityutskiy@nokia.com> Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
2010-05-10mtd/nand/fsl_upm: Replace the dangerous to_fsl_upm_nand macroFerenc Wagner
The original macro worked only when applied to variables named 'mtd'. While this could have been fixed by simply renaming the macro argument, a more type-safe replacement is preferred. Signed-off-by: Ferenc Wagner <wferi@niif.hu> Signed-off-by: Artem Bityutskiy <Artem.Bityutskiy@nokia.com> Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
2010-05-10mtd: OneNAND: OMAP2/3: unmap correct DMA bufferMika Westerberg
Functions omap2_onenand_write_bufferram() and omap3_onenand_write_bufferram() map the write buffer and store the returned handle in variable dma_src. However, when DMA unmap is done, variable dma_dst is used instead of the correct dma_src. This patch fixes them to use the correct DMA buffer. Signed-off-by: Mika Westerberg <ext-mika.1.westerberg@nokia.com> Tested-by: Arnaud Ebalard <arno@natisbad.org> Acked-by: Adrian Hunter <adrian.hunter@nokia.com> Signed-off-by: Artem Bityutskiy <Artem.Bityutskiy@nokia.com> Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
2010-05-10mtd: Blackfin NFC: localize MMR bit masksMike Frysinger
Convert all magic numbers into appropriate defines, and move the defines out of the global namespace and into this one driver. No other driver needs to care about the MMR layout anyways. Signed-off-by: Mike Frysinger <vapier@gentoo.org> Signed-off-by: Artem Bityutskiy <Artem.Bityutskiy@nokia.com> Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
2010-05-10mtd: kconfig: remove stray endchoice from help textFerenc Wagner
Signed-off-by: Ferenc Wagner <wferi@niif.hu> Signed-off-by: Artem Bityutskiy <Artem.Bityutskiy@nokia.com> Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
2010-05-10mtd: nandsim: make some structures anonymousArtem Bityutskiy
We do not need these names. Moreover, there are spelling typos there: "nansin" instead of "nandsim". This patch is just a clean up, no functional changes. Reported-by: Ferenc Wagner <wferi@niif.hu> Signed-off-by: Artem Bityutskiy <Artem.Bityutskiy@nokia.com> Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
2010-05-10mtd: mtdram.h: checkpatch cleanupAndrea Gelmini
include/linux/mtd/mtdram.h:6: ERROR: code indent should use tabs where possible Signed-off-by: Andrea Gelmini <andrea.gelmini@gelma.net> Signed-off-by: Artem Bityutskiy <Artem.Bityutskiy@nokia.com> Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
2010-05-09Linux 2.6.34-rc7v2.6.34-rc7Linus Torvalds
2010-05-09Merge git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi-rc-fixes-2.6Linus Torvalds
* git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi-rc-fixes-2.6: [SCSI] Retry commands with UNIT_ATTENTION sense codes to fix ext3/ext4 I/O error [SCSI] Enable retries for SYNCRONIZE_CACHE commands to fix I/O error [SCSI] scsi_debug: virtual_gb ignores sector_size [SCSI] libiscsi: regression: fix header digest errors [SCSI] fix locking around blk_abort_request() [SCSI] advansys: fix narrow board error path
2010-05-09cpuidle: Fix incorrect optimizationArjan van de Ven
commit 672917dcc78 ("cpuidle: menu governor: reduce latency on exit") added an optimization, where the analysis on the past idle period moved from the end of idle, to the beginning of the new idle. Unfortunately, this optimization had a bug where it zeroed one key variable for new use, that is needed for the analysis. The fix is simple, zero the variable after doing the work from the previous idle. During the audit of the code that found this issue, another issue was also found; the ->measured_us data structure member is never set, a local variable is always used instead. Signed-off-by: Arjan van de Ven <arjan@linux.intel.com> Cc: Corrado Zoccolo <czoccolo@gmail.com> Cc: stable@kernel.org Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
generated by cgit v1.2.3 (git 2.0.4) at 2024-11-05 16:41:25 +0000