| Age | Commit message (Collapse) | Author |
|---|
|
commit 70a062286b9dfcbd24d2e11601aecfead5cf709a upstream.
Fixes a hang when booting as dom0 under Xen, when jiffies can be
quite large by the time the kernel init gets this far.
Signed-off-by: Tim Deegan <Tim.Deegan@citrix.com>
[jbeulich@novell.com: !time_after() -> time_before_eq() as suggested by Jiri Slaby]
Signed-off-by: Jan Beulich <jbeulich@novell.com>
Cc: Jiri Slaby <jslaby@suse.cz>
Cc: Jeremy Fitzhardinge <jeremy@goop.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
|
commit f7448548a9f32db38f243ccd4271617758ddfe2c upstream.
Markus Kohn ran into a hard hang regression on an acer aspire
1310, when acpi is enabled. git bisect showed the following
commit as the bad one that introduced the boot regression.
commit d0af9eed5aa91b6b7b5049cae69e5ea956fd85c3
Author: Suresh Siddha <suresh.b.siddha@intel.com>
Date: Wed Aug 19 18:05:36 2009 -0700
x86, pat/mtrr: Rendezvous all the cpus for MTRR/PAT init
Because of the UP configuration of that platform,
native_smp_prepare_cpus() bailed out (in smp_sanity_check())
before doing the set_mtrr_aps_delayed_init()
Further down the boot path, native_smp_cpus_done() will call the
delayed MTRR initialization for the AP's (mtrr_aps_init()) with
mtrr_aps_delayed_init not set. This resulted in the boot
processor reprogramming its MTRR's to the values seen during the
start of the OS boot. While this is not needed ideally, this
shouldn't have caused any side-effects. This is because the
reprogramming of MTRR's (set_mtrr_state() that gets called via
set_mtrr()) will check if the live register contents are
different from what is being asked to write and will do the actual
write only if they are different.
BP's mtrr state is read during the start of the OS boot and
typically nothing would have changed when we ask to reprogram it
on BP again because of the above scenario on an UP platform. So
on a normal UP platform no reprogramming of BP MTRR MSR's
happens and all is well.
However, on this platform, bios seems to be modifying the fixed
mtrr range registers between the start of OS boot and when we
double check the live registers for reprogramming BP MTRR
registers. And as the live registers are modified, we end up
reprogramming the MTRR's to the state seen during the start of
the OS boot.
During ACPI initialization, something in the bios (probably smi
handler?) don't like this fact and results in a hard lockup.
We didn't see this boot hang issue on this platform before the
commit d0af9eed5aa91b6b7b5049cae69e5ea956fd85c3, because only
the AP's (if any) will program its MTRR's to the value that BP
had at the start of the OS boot.
Fix this issue by checking mtrr_aps_delayed_init before
continuing further in the mtrr_aps_init(). Now, only AP's (if
any) will program its MTRR's to the BP values during boot.
Addresses https://bugzilla.novell.com/show_bug.cgi?id=623393
[ By the way, this behavior of the bios modifying MTRR's after the start
of the OS boot is not common and the kernel is not prepared to
handle this situation well. Irrespective of this issue, during
suspend/resume, linux kernel will try to reprogram the BP's MTRR values
to the values seen during the start of the OS boot. So suspend/resume might
be already broken on this platform for all linux kernel versions. ]
Reported-and-bisected-by: Markus Kohn <jabber@gmx.org>
Tested-by: Markus Kohn <jabber@gmx.org>
Signed-off-by: Suresh Siddha <suresh.b.siddha@intel.com>
Cc: Thomas Renninger <trenn@novell.com>
Cc: Rafael Wysocki <rjw@novell.com>
Cc: Venkatesh Pallipadi <venki@google.com>
LKML-Reference: <1296694975.4418.402.camel@sbsiddha-MOBL3.sc.intel.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
|
commit 01e05e9a90b8f4c3997ae0537e87720eb475e532 upstream.
The wake_up_process() call in ptrace_detach() is spurious and not
interlocked with the tracee state. IOW, the tracee could be running or
sleeping in any place in the kernel by the time wake_up_process() is
called. This can lead to the tracee waking up unexpectedly which can be
dangerous.
The wake_up is spurious and should be removed but for now reduce its
toxicity by only waking up if the tracee is in TRACED or STOPPED state.
This bug can possibly be used as an attack vector. I don't think it
will take too much effort to come up with an attack which triggers oops
somewhere. Most sleeps are wrapped in condition test loops and should
be safe but we have quite a number of places where sleep and wakeup
conditions are expected to be interlocked. Although the window of
opportunity is tiny, ptrace can be used by non-privileged users and with
some loading the window can definitely be extended and exploited.
Signed-off-by: Tejun Heo <tj@kernel.org>
Acked-by: Roland McGrath <roland@redhat.com>
Acked-by: Oleg Nesterov <oleg@redhat.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
|
commit d0694e2aeb815042aa0f3e5036728b3db4446f1d upstream.
Unbreak Billionton CF bluetooth card. This actually fixes a regression
on zaurus.
Signed-off-by: Pavel Machek <pavel@ucw.cz>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
|
commit 5219bf884b6e2b54e734ca1799b6f0014bb2b4b7 upstream.
Remove real devices first and dummy devices last. This gives device
driver which instantiated dummy devices themselves a chance to clean
them up before we do.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Tested-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
|
commit 3b5c5827d1f80ad8ae844a8b1183f59ddb90fe25 upstream.
P54_HDR_FLAG_DATA_OUT_SEQNR is meant to tell the
firmware that "the frame's sequence number has
already been set by the application."
Whereas IEEE80211_TX_CTL_ASSIGN_SEQ is set for
frames which lack a valid sequence number and
either the driver or firmware has to assign one.
Yup, it's the exact opposite!
Signed-off-by: Christian Lamparter <chunkeey@googlemail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
|
commit 86af95039b69a90db15294eb1f9c147f1df0a8ea upstream.
A check against division by zero was modified in commit b0525b48.
Since this change time_to_empty_now is always reported as zero
while the battery is discharging and as a negative value while
the battery is charging. This is because current is negative while
the battery is discharging.
Fix the check introduced by commit b0525b48 so that time_to_empty_now
is reported correctly during discharge and as zero while charging.
Signed-off-by: Sven Neumann <s.neumann@raumfeld.com>
Acked-by: Daniel Mack <daniel@caiaq.de>
Signed-off-by: Anton Vorontsov <cbouatmailru@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
|
commit 8b3bb3ecf1934ac4a7005ad9017de1127e2fbd2f upstream.
We sometimes need to map between the virtio device and
the given pci device. One such use is OS installer that
gets the boot pci device from BIOS and needs to
find the relevant block device. Since it can't,
installation fails.
Instead of creating a top-level devices/virtio-pci
directory, create each device under the corresponding
pci device node. Symlinks to all virtio-pci
devices can be found under the pci driver link in
bus/pci/drivers/virtio-pci/devices, and all virtio
devices under drivers/bus/virtio/devices.
Signed-off-by: Milton Miller <miltonm@bga.com>
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
Acked-by: Michael S. Tsirkin <mst@redhat.com>
Tested-by: Michael S. Tsirkin <mst@redhat.com>
Acked-by: Gleb Natapov <gleb@redhat.com>
Tested-by: "Daniel P. Berrange" <berrange@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
|
commit 99a0fadf561e1f553c08f0a29f8b2578f55dd5f0 upstream.
pci-stub uses strsep() to separate list of ids and generates a warning
message when it fails to parse an id. However, not specifying the
parameter results in ids set to an empty string. strsep() happily
returns the empty string as the first token and thus triggers the
warning message spuriously.
Make the tokner ignore zero length ids.
Reported-by: Chris Wright <chrisw@sous-sol.org>
Reported-by: Prasad Joshi <P.G.Joshi@student.reading.ac.uk>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
|
commit 12a4dc43911785f51a596f771ae0701b18d436f1 upstream.
In fsl_rio_dbell_handler() the code currently simply acknowledges the QFI
queue full interrupt, but does nothing to resolve the queue full
condition. Instead, it jumps to the end of the isr. When a queue full
condition occurs, the isr is then re-entered immediately and continually,
forever.
The fix is to just fall through and read out current doorbell entries.
Signed-off-by: Thomas Taranowski <tom@baringforge.com>
Cc: Alexandre Bounine <alexandre.bounine@idt.com>
Cc: Kumar Gala <galak@kernel.crashing.org>
Cc: Matt Porter <mporter@kernel.crashing.org>
Cc: Li Yang <leoli@freescale.com>
Cc: Thomas Moll <thomas.moll@sysgo.com>
Cc: Micha Nelissen <micha@neli.hopto.org>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Grant Likely <grant.likely@secretlab.ca>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
|
commit 3dd823e6b86407aed1a025041d8f1df77e43a9c8 upstream.
With commit 554d1d027b19265c4aa3f718b3126d2b86e09a08 only one RF_KILL
interrupt will be seen by the driver when the interface is down.
Re-enable the interrupt when it occurs to see all transitions.
Signed-off-by: Don Fry <donald.h.fry@intel.com>
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
|
commit 2fb08e6ca9f00d1aedb3964983e9c8f84b36b807 upstream.
rtc-cmos was setting suspend/resume hooks at the device_driver level.
However, the platform bus code (drivers/base/platform.c) only looks for
resume hooks at the dev_pm_ops level, or within the platform_driver.
Switch rtc_cmos to use dev_pm_ops so that suspend/resume code is executed
again.
Paul said:
: The user visible symptom in our (XO laptop) case was that rtcwake would
: fail to wake the laptop. The RTC alarm would expire, but the wakeup
: wasn't unmasked.
:
: As for severity, the impact may have been reduced because if I recall
: correctly, the bug only affected platforms with CONFIG_PNP disabled.
Signed-off-by: Paul Fox <pgf@laptop.org>
Signed-off-by: Daniel Drake <dsd@laptop.org>
Acked-by: Rafael J. Wysocki <rjw@sisk.pl>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
|
commit 839f7ad6932d95f4d5ae7267b95c574714ff3d5b upstream.
Nick Piggin reports:
> I'm getting use after frees in aio code in NFS
>
> [ 2703.396766] Call Trace:
> [ 2703.396858] [<ffffffff8100b057>] ? native_sched_clock+0x27/0x80
> [ 2703.396959] [<ffffffff8108509e>] ? put_lock_stats+0xe/0x40
> [ 2703.397058] [<ffffffff81088348>] ? lock_release_holdtime+0xa8/0x140
> [ 2703.397159] [<ffffffff8108a2a5>] lock_acquire+0x95/0x1b0
> [ 2703.397260] [<ffffffff811627db>] ? aio_put_req+0x2b/0x60
> [ 2703.397361] [<ffffffff81039701>] ? get_parent_ip+0x11/0x50
> [ 2703.397464] [<ffffffff81612a31>] _raw_spin_lock_irq+0x41/0x80
> [ 2703.397564] [<ffffffff811627db>] ? aio_put_req+0x2b/0x60
> [ 2703.397662] [<ffffffff811627db>] aio_put_req+0x2b/0x60
> [ 2703.397761] [<ffffffff811647fe>] do_io_submit+0x2be/0x7c0
> [ 2703.397895] [<ffffffff81164d0b>] sys_io_submit+0xb/0x10
> [ 2703.397995] [<ffffffff8100307b>] system_call_fastpath+0x16/0x1b
>
> Adding some tracing, it is due to nfs completing the request then
> returning something other than -EIOCBQUEUED, so aio.c
> also completes the request.
To address this, prevent the NFS direct I/O engine from completing
async iocbs when the forward path returns an error without starting
any I/O.
This fix appears to survive ^C during both "xfstest no. 208" and "fsx
-Z."
It's likely this bug has existed for a very long while, as we are seeing
very similar symptoms in OEL 5. Copying stable.
Signed-off-by: Chuck Lever <chuck.lever@oracle.com>
Signed-off-by: Trond Myklebust <Trond.Myklebust@netapp.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
|
commit e9c2048915048d605fd76539ddd96f00d593e1eb upstream.
We need to tweak how we query the active capture/playback state after
the recent overhauls of common code.
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
|
commit 7ebcf5d6021a696680ee77d9162a2edec2d671dd upstream.
Signed-off-by: Dimitris Papastamos <dp@opensource.wolfsonmicro.com>
Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
|
commit b1d4f7f4bdcf9915c41ff8cfc4425c84dabb1fde upstream.
If a timer interrupt was delayed too much, hrtimer_forward_now() will
forward the timer expiry more than once. When this happens, the
additional number of elapsed ALSA timer ticks must be passed to
snd_timer_interrupt() to prevent the ALSA timer from falling behind.
This mostly fixes MIDI slowdown problems on highly-loaded systems with
badly behaved interrupt handlers.
Signed-off-by: Clemens Ladisch <clemens@ladisch.de>
Reported-and-tested-by: Arthur Marsh <arthur.marsh@internode.on.net>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
|
commit 6021afcf19d8c6f5db6d11cadcfb6a22d0c28a48 upstream.
This patch adds support for the MacBookAir3,1 and MacBookAir3,2
models.
[rydberg@euromail.se: touchpad range calibration]
Signed-off-by: Edgar (gimli) Hucek <gimli@dark-green.com>
Signed-off-by: Henrik Rydberg <rydberg@euromail.se>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
|
commit f8313ef1f448006207f12c107123522c8bc00f15 upstream.
i8042 controller present in Dell Vostro V13 errorneously signals spurious
timeouts.
Introduce i8042.notimeout parameter for ignoring i8042-signalled timeouts
and apply this quirk automatically for Dell Vostro V13, based on DMI match.
In addition to that, this machine also needs to be added to nomux blacklist.
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
Cc: Tim Gardner <tcanonical@tpi.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
|
commit 70f7db11c45a313b23922cacf248c613c3b2144c upstream.
The Conexant codec driver adds the jack arrays in init callback which
may be called also in each PM resume. This results in the addition of
new jack element at each time.
The fix is to check whether the requested jack is already present in
the array.
Reference: Novell bug 668929
https://bugzilla.novell.com/show_bug.cgi?id=668929
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
|
commit d757534ed15387202e322854cd72dc58bbb975de upstream.
This typo caused the dmesg output of the supported bits of HDMI
to be cut off early.
Signed-off-by: David Henningsson <david.henningsson@canonical.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
|
commit d9ab344336f74c012f6643ed3d1ad8ca0136de3b upstream.
Fix playback/capture channels patch to change supported playback
channels of au8830 to 1,2,4 and capture channels to 1,2.
This prevent oops when oss emulation use SNDCTL_DSP_CHANNELS to
set 3 Channels
Signed-off-by: Raymond Yau <superquad.vortex2@gmail.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
|
commit a3fa904ec79b94f0db7faed010ff94d42f7d1d47 upstream.
The audio input line was wrong. Fix it.
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
|
commit e3c92215198cb6aa00ad38db2780faa6b72e0a3f upstream.
gcc 4.5+ doesn't properly evaluate some inlined expressions.
A previous patch were proposed by Andrew Morton using noinline.
However, the entire inlined function is bogus, so let's just
remove it and be happy.
Reported-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
|
commit 4224489f45b503f0a1f1cf310f76dc108f45689a upstream.
There was a configuration page timing out during the initial port
enable at driver load time. The port enable would fail, and this would
result in the driver unloading itself, meanwhile the driver was accessing
freed memory in another context resulting in the panic. The fix is to
prevent access to freed memory once the driver had issued the diag reset
which woke up the sleeping port enable process. The routine
_base_reset_handler was reorganized so the last sleeping process woken up was
the port_enable.
Signed-off-by: Kashyap Desai <kashyap.desai@lsi.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
|
commit 11e1b961ab067ee3acaf723531da4d3f23e1d6f7 upstream.
The ioc->hba_queue_depth is not properly resized when the controller
firmware reports that it supports more outstanding IO than what can be fit
inside the reply descriptor pool depth. This is reproduced by setting the
controller global credits larger than 30,000. The bug results in an
incorrect sizing of the queues. The fix is to resize the queue_size by
dividing queue_diff by two.
Signed-off-by: Kashyap Desai <kashyap.desai@lsi.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
|
commit 4dc2757a2e9a9d1f2faee4fc6119276fc0061c16 upstream.
When zoning end devices, the driver is not sending device
removal handshake alogrithm to firmware. This results in controller
firmware not sending sas topology add events the next time the device is
added. The fix is the driver should be doing the device removal handshake
even though the PHYSTATUS_VACANT bit is set in the PhyStatus of the
event data. The current design is avoiding the handshake when the
VACANT bit is set in the phy status.
Signed-off-by: Kashyap Desai <kashyap.desai@lsi.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
|
commit 9ee91f7fb550a4c82f82d9818e42493484c754af upstream.
libsas makes use of scsi_schedule_eh() but forgets to clear the
host_eh_scheduled flag in its error handling routine. Because of this,
the error handler thread never gets to sleep; it's constantly awake and
trying to run the error routine leading to console spew and inability to
run anything else (at least on a UP system). The fix is to clear the
flag as we splice the work queue.
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
|
commit a8733c7baf457b071528e385a0b7d4aaec79287c upstream.
Our current handling of medium error assumes that data is returned up
to the bad sector. This assumption holds good for all disk devices,
all DIF arrays and most ordinary arrays. However, an LSI array engine
was recently discovered which reports a medium error without returning
any data. This means that when we report good data up to the medium
error, we've reported junk originally in the buffer as good. Worse,
if the read consists of requested data plus a readahead, and the error
occurs in readahead, we'll just strip off the readahead and report
junk up to userspace as good data with no error.
The fix for this is to have the error position computation take into
account the amount of data returned by the driver using the scsi
residual data. Unfortunately, not every driver fills in this data,
but for those who don't, it's set to zero, which means we'll think a
full set of data was transferred and the behaviour will be identical
to the prior behaviour of the code (believe the buffer up to the error
sector). All modern drivers seem to set the residual, so that should
fix up the LSI failure/corruption case.
Reported-by: Douglas Gilbert <dgilbert@interlog.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
|
commit 13c6680acb3df25722858566b42759215ea5d2e0 upstream.
The glibc vdso code for s390 uses the version string 2.6.29, the
kernel uses the version string 2.6.26. No wonder the vdso code
is never used. The first kernel version to contain the vdso code
is 2.6.29 which makes this the correct version.
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Cc: maximilian attems <max@stro.at>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
|
commit 39ec2997c374b528cdbf65099b6d6b8593a67f7f upstream.
There is a roundng error in delimiter padding computation
which causes severe throughput drop with some of AR9003.
signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: Vasanthakumar Thiagarajan <vasanth@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
|
commit 554d1d027b19265c4aa3f718b3126d2b86e09a08 upstream.
Since commit 6cd0b1cb872b3bf9fc5de4536404206ab74bafdd "iwlagn: fix
hw-rfkill while the interface is down", we enable interrupts when
device is not ready to receive them. However hardware, when it is in
some inconsistent state, can generate other than rfkill interrupts
and crash the system. I can reproduce crash with "kernel BUG at
drivers/net/wireless/iwlwifi/iwl-agn.c:1010!" message, when forcing
firmware restarts.
To fix only enable rfkill interrupt when down device and after probe.
I checked patch on laptop with 5100 device, rfkill change is still
passed to user space when device is down.
Signed-off-by: Stanislaw Gruszka <sgruszka@redhat.com>
Acked-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
|
commit 91a970d9889c7d6f451ee91ed361d0f0119d3778 upstream.
The device driver must allocate memory for IUCV buffers with GFP_DMA,
because IUCV cannot address memory above 2GB (31bit addresses only).
Because the IUCV ignores the higher bits of the address, sending and
receiving IUCV data with this driver might cause memory corruptions.
Signed-off-by: Hendrik Brueckner <brueckner@linux.vnet.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Cc: maximilian attems <max@stro.at>
|
|
commit 7c161d0b900ea9bd9fc5ea5d3fa9916e9eb0dd88 upstream.
The hv_netvsc gets RNDIS_STATUS_MEDIA_CONNECT event after the VM
is live migrated. Adding call to netif_notify_peers() for this event
to send GARP (Gratuitous ARP) to notify network peers. Otherwise,
the VM's network connection may stop after a live migration.
This patch should also be applied to stable kernel 2.6.32 and later.
Signed-off-by: Haiyang Zhang <haiyangz@microsoft.com>
Signed-off-by: Hank Janssen <hjanssen@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
|
commit 268eff909afaca93188d2d14554cbf824f6a0e41 upstream.
The block device does not create the proper symlink in sysfs because we
forgot to set up the gendisk structure properly. This patch fixes the
issue.
Signed-off-by: K. Y. Srinivasan <ksrinivasan@novell.com>
Cc: Hank Janssen <hjanssen@microsoft.com>
Cc: Haiyang Zhang <haiyangz@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
|
commit d1ce318496f5943d2cc5e20171fc383a59a1421f upstream.
The ni_labpc driver module only requests a shared IRQ for PCI devices,
requesting a non-shared IRQ for non-PCI devices.
As this module is also used by the ni_labpc_cs module for certain
National Instruments PCMCIA cards, it also needs to request a shared IRQ
for PCMCIA devices, otherwise you get a IRQ mismatch with the CardBus
controller.
Signed-off-by: Ian Abbott <abbotti@mev.co.uk>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
|
commit 6292817d58637f85dd623cfe563c7f5ec4f4c470 upstream.
add DEVICE_ID to table
Signed-off-by: Ruben Smits <ruben.smits@mech.kuleuven.be>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
|
commit d199c96d41d80a567493e12b8e96ea056a1350c1 upstream.
If anyone comes across a high-speed hub that (by mistake or by design)
claims to have no Transaction Translators, plugging a full- or
low-speed device into it will cause the USB stack to crash. This
patch (as1446) prevents the problem by ignoring such devices, since
the kernel has no way to communicate with them.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Tested-by: Perry Neben <neben@vmware.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
|
commit 28fe2eb0162a1d23370dd99ff7d0e35632b1ee91 upstream.
Add the USB Vendor ID and Product ID for a Acton Research Corp.
spectrograph device with a FTDI chip for serial I/O.
Signed-off-by: Michael H Williamson <michael.h.williamson@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
|
commit 721d92fc6373dee15846216f9d178ec240ec0fd7 upstream.
This adds the N8 to the list of devices in cdc-acm, in order to get the
secondary ACM device exposed.
In the spirit of:
http://kerneltrap.org/mailarchive/linux-usb/2010/9/4/6264554
Signed-off-by: Arvid Ephraim Picciani <arvid.picciani@nokia.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
|
commit 6ec2f46c4b4abf48c88c0ae7c476f347b97e1105 upstream.
on ST Micro Connect Lite we have 4 port
Part A and B for the JTAG
Port C Uart
Port D for PIO
Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
|
commit c25f6b1591b158f7ae3b9132367d0fa6d632e70e upstream.
This device suffers from the off-by-one error when reporting the capacity,
so add entry with US_FL_FIX_CAPACITY.
Signed-off-by: Nick Holloway <Nick.Holloway@pyrites.org.uk>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
|
commit b14de3857227cd978f515247853fd15cc2425d3e upstream.
If usb_deregister() is called after usb_serial_deregister() when
the device is plugged in, the following Oops occurs:
[ 95.337377] BUG: unable to handle kernel NULL pointer dereference at 00000010
[ 95.338236] IP: [<c0776b2d>] klist_put+0x12/0x62
[ 95.338356] *pdpt = 000000003001a001 *pde = 0000000000000000
[ 95.338356] Oops: 0000 [#1] SMP
[ 95.340499] last sysfs file: /sys/devices/pci0000:00/0000:00:1d.2/usb8/idVendor
[ 95.340499] Modules linked in: ti_usb_3410_5052(-) usbserial cpufreq_ondemand acpi_cpufreq mperf iptable_nat nf_nat iptable_mangle ip6t_REJECT nf_conntrack_ipv6 nf_defrag_ipv6 ip6table_filter ip6_tables ipv6 uinput arc4 ecb iwlagn iwlcore mac80211 cfg80211 microcode pcspkr acer_wmi joydev wmi sky2 [last unloaded: scsi_wait_scan]
[ 95.341908]
[ 95.341908] Pid: 1532, comm: modprobe Not tainted 2.6.37-rc7+ #6 Eiger /Aspire 5930
[ 95.341908] EIP: 0060:[<c0776b2d>] EFLAGS: 00010246 CPU: 0
[ 95.341908] EIP is at klist_put+0x12/0x62
[ 95.341908] EAX: 00000000 EBX: eedc0c84 ECX: c09c21b4 EDX: 00000001
[ 95.341908] ESI: 00000000 EDI: efaa0c1c EBP: f214fe2c ESP: f214fe1c
[ 95.341908] DS: 007b ES: 007b FS: 00d8 GS: 00e0 SS: 0068
[ 95.341908] Process modprobe (pid: 1532, ti=f214e000 task=efaaf080 task.ti=f214e000)
[ 95.341908] Stack:
[ 95.341908] f214fe24 eedc0c84 efaaf080 efaa0c1c f214fe34 c0776ba8 f214fe5c c0776c76
[ 95.341908] c09c21b4 c09c21b4 eedc0c84 efaaf080 00000000 c0634398 eafe2d1c f7b515f0
[ 95.341908] f214fe6c c0631b5c eafe2d50 eafe2d1c f214fe7c c0631ba2 eafe2d1c eafe2c00
[ 95.341908] Call Trace:
[ 95.341908] [<c0776ba8>] ? klist_del+0xd/0xf
[ 95.341908] [<c0776c76>] ? klist_remove+0x48/0x74
[ 95.341908] [<c0634398>] ? devres_release_all+0x49/0x51
[ 95.341908] [<c0631b5c>] ? __device_release_driver+0x7b/0xa4
[ 95.341908] [<c0631ba2>] ? device_release_driver+0x1d/0x28
[ 95.341908] [<c06317c4>] ? bus_remove_device+0x92/0xa1
[ 95.341908] [<c062f3d8>] ? device_del+0xf9/0x13e
[ 95.341908] [<f7b06146>] ? usb_serial_disconnect+0xd9/0x116 [usbserial]
[ 95.341908] [<c0681e3f>] ? usb_disable_interface+0x32/0x40
[ 95.341908] [<c0683972>] ? usb_unbind_interface+0x48/0xfd
[ 95.341908] [<c0631b43>] ? __device_release_driver+0x62/0xa4
[ 95.341908] [<c06320b9>] ? driver_detach+0x62/0x81
[ 95.341908] [<c0631a41>] ? bus_remove_driver+0x8f/0xae
[ 95.341908] [<c063214c>] ? driver_unregister+0x50/0x57
[ 95.341908] [<c0682f95>] ? usb_deregister+0x77/0x84
[ 95.341908] [<f7b505b6>] ? ti_exit+0x26/0x28 [ti_usb_3410_5052]
[ 95.341908] [<c046a307>] ? sys_delete_module+0x181/0x1de
[ 95.341908] [<c04e2727>] ? path_put+0x1a/0x1d
[ 95.341908] [<c047f4c5>] ? audit_syscall_entry+0x116/0x138
[ 95.341908] [<c04094df>] ? sysenter_do_call+0x12/0x28
[ 95.341908] Code: 00 83 7d f0 00 74 09 85 f6 74 05 89 f0 ff 55 f0 8b 43 04 5a 5b 5e 5f 5d c3 55 89 e5 57 56 53 89 c3 83 ec 04 8b 30 83 e6 fe 89 f0 <8b> 7e 10 88 55 f0 e8 47 26 01 00 8a 55 f0 84 d2 74 17 f6 03 01
[ 95.341908] EIP: [<c0776b2d>] klist_put+0x12/0x62 SS:ESP 0068:f214fe1c
[ 95.341908] CR2: 0000000000000010
[ 95.342357] ---[ end trace 8124d00ad871ad18 ]---
Signed-off-by: Ionut Nicu <ionut.nicu@mindbit.ro>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
|
commit 271c1150b4f8e1685e5a8cbf76e329ec894481da upstream.
The major and minor number saved in the product_info structure
were copied from the address instead of the data, causing an
inconsistency in the reported versions during firmware loading:
usb 4-1: firmware: requesting edgeport/down.fw
/usr/src/linux/drivers/usb/serial/io_edgeport.c: downloading firmware version (930) 1.16.4
[..]
/usr/src/linux/drivers/usb/serial/io_edgeport.c: edge_startup - time 3 4328191260
/usr/src/linux/drivers/usb/serial/io_edgeport.c: FirmwareMajorVersion 0.0.4
This can cause some confusion whether firmware loaded successfully
or not.
Signed-off-by: Bjørn Mork <bjorn@mork.no>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
|
commit ad84e4a9efb7c8ed322bafb6ebdb9c3a49a3d3a8 upstream.
This patch (as1442) fixes a bug in g_printer: Module parameters should
not be marked "__initdata" if they are accessible in sysfs (i.e., if
the mode value in the module_param() macro is nonzero). Otherwise
attempts to access the parameters will cause addressing violations.
Character-string module parameters must not be marked "__initdata"
if the module can be unloaded, because the kernel needs to access the
parameter variable at unload time in order to free the
dynamically-allocated string.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
CC: Roland Kletzing <devzero@web.de>
CC: Craig W. Nadler <craig@nadler.us>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
|
commit f75593ceaa08e6d27aec1a5de31cded19e850dd1 upstream.
This patch (as1440) fixes a bug in ehci-hcd. ehci->periodic_size is
used to compute the size in a dma_alloc_coherent() call, but then it
gets changed later on. As a result, the corresponding call to
dma_free_coherent() passes a different size from the original
allocation. Fix the problem by adjusting ehci->periodic_size before
carrying out any of the memory allocations.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Tested-by: Larry Finger <Larry.Finger@lwfinger.net>
CC: David Brownell <david-b@pacbell.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
|
commit baab93afc2844b68d57b0dcca5e1d34c5d7cf411 upstream.
AMD Hudson also needs the same ASPM quirk as SB800
Signed-off-by: Alex He <alex.he@amd.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
|
commit aa52b3a92918039b273fc9d1994bd34227c40269 upstream.
/drivers/usb/serial/option.c: Adding support for Cinterion's HC25, HC28,
HC28J, EU3-E, EU3-P and PH8 by correcting/adding Cinterion's and
Siemens' Vendor IDs as well as Product IDs and USB_DEVICE tuples
Signed-off-by: Nicolaus Colberg <nicolaus.colberg@cinterion.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
|
commit a9d61bc49188e32d2ae9cf0f683cde3e1744feef upstream.
I found the original patch on the db0fhn repeater wiki (couldn't find the email
of the origial author) I guess it was never commited.
I updated and added some Icom HAM-radio devices to the ftdi driver.
Added extra comments to make clear what devices it are.
Signed-off-by: Pieter Maes <maescool@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
|
commit 3ea3c9b5a8464ec8223125f95e5dddb3bfd02a39 upstream.
This patch (as1444) adds an unusual_devs entry for an MP3 player from
Coby electronics. The device has two nasty bugs.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Tested-by: Jasper Mackenzie <scarletpimpernal@hotmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
|
commit 12f68c480c7155a66bd2a76ab2fef28dd5f93fa2 upstream.
This patch (as1438) adds an unusual_devs entry for the MagicPixel
FW_Omega2 chip, used in the CamSport Evo camera. The firmware
incorrectly reports a vendor-specific bDeviceClass.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Reported-by: <ttkspam@free.fr>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
