summaryrefslogtreecommitdiff
AgeCommit message (Collapse)Author
2014-07-18tty: Correct INPCK handlingPeter Hurley
commit 66528f90669691c85c73bea4f0c9f4a5857c4cab upstream. If INPCK is not set, input parity detection should be disabled. This means parity errors should not be received from the tty driver, and the data received should be treated normally. SUS v3, 11.2.2, General Terminal Interface - Input Modes, states: "If INPCK is set, input parity checking shall be enabled. If INPCK is not set, input parity checking shall be disabled, allowing output parity generation without input parity errors. Note that whether input parity checking is enabled or disabled is independent of whether parity detection is enabled or disabled (see Control Modes). If parity detection is enabled but input parity checking is disabled, the hardware to which the terminal is connected shall recognize the parity bit, but the terminal special file shall not check whether or not this bit is correctly set." Ignore parity errors reported by the tty driver when INPCK is not set, and handle the received data normally. Fixes: Bugzilla #71681, 'Improvement of n_tty_receive_parity_error from n_tty.c' Reported-by: Ivan <athlon_@mail.ru> Signed-off-by: Peter Hurley <peter@hurleysoftware.com> Signed-off-by: Jiri Slaby <jslaby@suse.cz>
2014-07-18serial: Fix IGNBRK handlingPeter Hurley
commit ef8b9ddcb45fa3b1e11acd72be2398001e807d14 upstream. If IGNBRK is set without either BRKINT or PARMRK set, some uart drivers send a 0x00 byte for BREAK without the TTYBREAK flag to the line discipline, when it should send either nothing or the TTYBREAK flag set. This happens because the read_status_mask masks out the BI condition, which uart_insert_char() then interprets as a normal 0x00 byte. SUS v3 is clear regarding the meaning of IGNBRK; Section 11.2.2, General Terminal Interface - Input Modes, states: "If IGNBRK is set, a break condition detected on input shall be ignored; that is, not put on the input queue and therefore not read by any process." Fix read_status_mask to include the BI bit if IGNBRK is set; the lsr status retains the BI bit if a BREAK is recv'd, which is subsequently ignored in uart_insert_char() when masked with the ignore_status_mask. Affected drivers: 8250 - all serial_txx9 mfd amba-pl010 amba-pl011 atmel_serial bfin_uart dz ip22zilog max310x mxs-auart netx-serial pnx8xxx_uart pxa sb1250-duart sccnxp serial_ks8695 sirfsoc_uart st-asc vr41xx_siu zs sunzilog fsl_lpuart sunsab ucc_uart bcm63xx_uart sunsu efm32-uart pmac_zilog mpsc msm_serial m32r_sio Unaffected drivers: omap-serial rp2 sa1100 imx icom Annotated for fixes: altera_uart mcf Drivers without break detection: 21285 xilinx-uartps altera_jtaguart apbuart arc-uart clps711x max3100 uartlite msm_serial_hs nwpserial lantiq vt8500_serial Unknown: samsung mpc52xx_uart bfin_sport_uart cpm_uart/core Fixes: Bugzilla #71651, '8250_core.c incorrectly handles IGNBRK flag' Reported-by: Ivan <athlon_@mail.ru> Signed-off-by: Peter Hurley <peter@hurleysoftware.com> Signed-off-by: Jiri Slaby <jslaby@suse.cz>
2014-07-18mm: page_alloc: fix CMA area initialisation when pageblock > MAX_ORDERMichal Nazarewicz
commit dc78327c0ea7da5186d8cbc1647bd6088c5c9fa5 upstream. With a kernel configured with ARM64_64K_PAGES && !TRANSPARENT_HUGEPAGE, the following is triggered at early boot: SMP: Total of 8 processors activated. devtmpfs: initialized Unable to handle kernel NULL pointer dereference at virtual address 00000008 pgd = fffffe0000050000 [00000008] *pgd=00000043fba00003, *pmd=00000043fba00003, *pte=00e0000078010407 Internal error: Oops: 96000006 [#1] SMP Modules linked in: CPU: 0 PID: 1 Comm: swapper/0 Not tainted 3.15.0-rc864k+ #44 task: fffffe03bc040000 ti: fffffe03bc080000 task.ti: fffffe03bc080000 PC is at __list_add+0x10/0xd4 LR is at free_one_page+0x270/0x638 ... Call trace: __list_add+0x10/0xd4 free_one_page+0x26c/0x638 __free_pages_ok.part.52+0x84/0xbc __free_pages+0x74/0xbc init_cma_reserved_pageblock+0xe8/0x104 cma_init_reserved_areas+0x190/0x1e4 do_one_initcall+0xc4/0x154 kernel_init_freeable+0x204/0x2a8 kernel_init+0xc/0xd4 This happens because init_cma_reserved_pageblock() calls __free_one_page() with pageblock_order as page order but it is bigger than MAX_ORDER. This in turn causes accesses past zone->free_list[]. Fix the problem by changing init_cma_reserved_pageblock() such that it splits pageblock into individual MAX_ORDER pages if pageblock is bigger than a MAX_ORDER page. In cases where !CONFIG_HUGETLB_PAGE_SIZE_VARIABLE, which is all architectures expect for ia64, powerpc and tile at the moment, the “pageblock_order > MAX_ORDER” condition will be optimised out since both sides of the operator are constants. In cases where pageblock size is variable, the performance degradation should not be significant anyway since init_cma_reserved_pageblock() is called only at boot time at most MAX_CMA_AREAS times which by default is eight. Signed-off-by: Michal Nazarewicz <mina86@mina86.com> Reported-by: Mark Salter <msalter@redhat.com> Tested-by: Mark Salter <msalter@redhat.com> Tested-by: Christopher Covington <cov@codeaurora.org> Cc: Mel Gorman <mgorman@suse.de> Cc: David Rientjes <rientjes@google.com> Cc: Marek Szyprowski <m.szyprowski@samsung.com> Cc: Catalin Marinas <catalin.marinas@arm.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org> Signed-off-by: Jiri Slaby <jslaby@suse.cz>
2014-07-18irqchip: spear_shirq: Fix interrupt offsetThomas Gleixner
commit 4f4366033945419b0c52118c29d3057d7c558765 upstream. The ras3 block on spear320 claims to have 3 interrupts. In fact it has one and 6 reserved interrupts. Account the 6 reserved to this block so it has 7 interrupts total. That matches the datasheet and the device tree entries. Broken since commit 80515a5a(ARM: SPEAr3xx: shirq: simplify and move the shared irq multiplexor to DT). Testing is overrated.... Signed-off-by: Thomas Gleixner <tglx@linutronix.de> Link: https://lkml.kernel.org/r/20140619212712.872379208@linutronix.de Fixes: 80515a5a2e3c ('ARM: SPEAr3xx: shirq: simplify and move the shared irq multiplexor to DT') Acked-by: Viresh Kumar <viresh.kumar@linaro.org> Signed-off-by: Jason Cooper <jason@lakedaemon.net> Signed-off-by: Jiri Slaby <jslaby@suse.cz>
2014-07-18md: flush writes before starting a recovery.NeilBrown
commit 133d4527eab8d199a62eee6bd433f0776842df2e upstream. When we write to a degraded array which has a bitmap, we make sure the relevant bit in the bitmap remains set when the write completes (so a 're-add' can quickly rebuilt a temporarily-missing device). If, immediately after such a write starts, we incorporate a spare, commence recovery, and skip over the region where the write is happening (because the 'needs recovery' flag isn't set yet), then that write will not get to the new device. Once the recovery finishes the new device will be trusted, but will have incorrect data, leading to possible corruption. We cannot set the 'needs recovery' flag when we start the write as we do not know easily if the write will be "degraded" or not. That depends on details of the particular raid level and particular write request. This patch fixes a corruption issue of long standing and so it suitable for any -stable kernel. It applied correctly to 3.0 at least and will minor editing to earlier kernels. Reported-by: Bill <billstuff2001@sbcglobal.net> Tested-by: Bill <billstuff2001@sbcglobal.net> Link: http://lkml.kernel.org/r/53A518BB.60709@sbcglobal.net Signed-off-by: NeilBrown <neilb@suse.de> Signed-off-by: Jiri Slaby <jslaby@suse.cz>
2014-07-18tracing: Remove ftrace_stop/start() from reading the trace fileSteven Rostedt (Red Hat)
commit 099ed151675cd1d2dbeae1dac697975f6a68716d upstream. Disabling reading and writing to the trace file should not be able to disable all function tracing callbacks. There's other users today (like kprobes and perf). Reading a trace file should not stop those from happening. Reviewed-by: Masami Hiramatsu <masami.hiramatsu.pt@hitachi.com> Signed-off-by: Steven Rostedt <rostedt@goodmis.org> Signed-off-by: Jiri Slaby <jslaby@suse.cz>
2014-07-18tools: ffs-test: fix header values endianessMichal Nazarewicz
commit f35f71244da6e51db4e1f2c7e318581f498ececf upstream. It appears that no one ever run ffs-test on a big-endian machine, since it used cpu-endianess for fs_count and hs_count fields which should be in little-endian format. Fix by wrapping the numbers in cpu_to_le32. Signed-off-by: Michal Nazarewicz <mina86@mina86.com> Signed-off-by: Felipe Balbi <balbi@ti.com> Signed-off-by: Jiri Slaby <jslaby@suse.cz>
2014-07-18nfsd: fix rare symlink decoding bugJ. Bruce Fields
commit 76f47128f9b33af1e96819746550d789054c9664 upstream. An NFS operation that creates a new symlink includes the symlink data, which is xdr-encoded as a length followed by the data plus 0 to 3 bytes of zero-padding as required to reach a 4-byte boundary. The vfs, on the other hand, wants null-terminated data. The simple way to handle this would be by copying the data into a newly allocated buffer with space for the final null. The current nfsd_symlink code tries to be more clever by skipping that step in the (likely) case where the byte following the string is already 0. But that assumes that the byte following the string is ours to look at. In fact, it might be the first byte of a page that we can't read, or of some object that another task might modify. Worse, the NFSv4 code tries to fix the problem by actually writing to that byte. In the NFSv2/v3 cases this actually appears to be safe: - nfs3svc_decode_symlinkargs explicitly null-terminates the data (after first checking its length and copying it to a new page). - NFSv2 limits symlinks to 1k. The buffer holding the rpc request is always at least a page, and the link data (and previous fields) have maximum lengths that prevent the request from reaching the end of a page. In the NFSv4 case the CREATE op is potentially just one part of a long compound so can end up on the end of a page if you're unlucky. The minimal fix here is to copy and null-terminate in the NFSv4 case. The nfsd_symlink() interface here seems too fragile, though. It should really either do the copy itself every time or just require a null-terminated string. Reported-by: Jeff Layton <jlayton@primarydata.com> Signed-off-by: J. Bruce Fields <bfields@redhat.com> Signed-off-by: Jiri Slaby <jslaby@suse.cz>
2014-07-18iio: of_iio_channel_get_by_name() returns non-null pointers for error legsAdam Thomson
commit a2c12493ed7e63a18cef33a71686d12ffcd6600e upstream. Currently in the inkern.c code for IIO framework, the function of_iio_channel_get_by_name() will return a non-NULL pointer when it cannot find a channel using of_iio_channel_get() and when it tries to search for 'io-channel-ranges' property and fails. This is incorrect behaviour as the function which calls this expects a NULL pointer for failure. This patch rectifies the issue. Signed-off-by: Adam Thomson <Adam.Thomson.Opensource@diasemi.com> Signed-off-by: Jonathan Cameron <jic23@kernel.org> Signed-off-by: Jiri Slaby <jslaby@suse.cz>
2014-07-18KVM: x86: preserve the high 32-bits of the PAT registerPaolo Bonzini
commit 7cb060a91c0efc5ff94f83c6df3ed705e143cdb9 upstream. KVM does not really do much with the PAT, so this went unnoticed for a long time. It is exposed however if you try to do rdmsr on the PAT register. Reported-by: Valentine Sinitsyn <valentine.sinitsyn@gmail.com> Signed-off-by: Paolo Bonzini <pbonzini@redhat.com> Signed-off-by: Jiri Slaby <jslaby@suse.cz>
2014-07-18KVM: x86: Increase the number of fixed MTRR regs to 10Nadav Amit
commit 682367c494869008eb89ef733f196e99415ae862 upstream. Recent Intel CPUs have 10 variable range MTRRs. Since operating systems sometime make assumptions on CPUs while they ignore capability MSRs, it is better for KVM to be consistent with recent CPUs. Reporting more MTRRs than actually supported has no functional implications. Signed-off-by: Nadav Amit <namit@cs.technion.ac.il> Signed-off-by: Paolo Bonzini <pbonzini@redhat.com> Signed-off-by: Jiri Slaby <jslaby@suse.cz>
2014-07-18ext4: Fix hole punching for files with indirect blocksJan Kara
commit a93cd4cf86466caa49cfe64607bea7f0bde3f916 upstream. Hole punching code for files with indirect blocks wrongly computed number of blocks which need to be cleared when traversing the indirect block tree. That could result in punching more blocks than actually requested and thus effectively cause a data loss. For example: fallocate -n -p 10240000 4096 will punch the range 10240000 - 12632064 instead of the range 1024000 - 10244096. Fix the calculation. Fixes: 8bad6fc813a3a5300f51369c39d315679fd88c72 Signed-off-by: Jan Kara <jack@suse.cz> Signed-off-by: Theodore Ts'o <tytso@mit.edu> Signed-off-by: Jiri Slaby <jslaby@suse.cz>
2014-07-18ext4: Fix buffer double free in ext4_alloc_branch()Jan Kara
commit c5c7b8ddfbf8cb3b2291e515a34ab1b8982f5a2d upstream. Error recovery in ext4_alloc_branch() calls ext4_forget() even for buffer corresponding to indirect block it did not allocate. This leads to brelse() being called twice for that buffer (once from ext4_forget() and once from cleanup in ext4_ind_map_blocks()) leading to buffer use count misaccounting. Eventually (but often much later because there are other users of the buffer) we will see messages like: VFS: brelse: Trying to free free buffer Another manifestation of this problem is an error: JBD2 unexpected failure: jbd2_journal_revoke: !buffer_revoked(bh); inconsistent data on disk The fix is easy - don't forget buffer we did not allocate. Also add an explanatory comment because the indexing at ext4_alloc_branch() is somewhat subtle. Signed-off-by: Jan Kara <jack@suse.cz> Signed-off-by: Theodore Ts'o <tytso@mit.edu> Signed-off-by: Jiri Slaby <jslaby@suse.cz>
2014-07-18blkcg: fix use-after-free in __blkg_release_rcu() by making blkcg_gq refcnt ↵Tejun Heo
an atomic_t commit a5049a8ae34950249a7ae94c385d7c5c98914412 upstream. Hello, So, this patch should do. Joe, Vivek, can one of you guys please verify that the oops goes away with this patch? Jens, the original thread can be read at http://thread.gmane.org/gmane.linux.kernel/1720729 The fix converts blkg->refcnt from int to atomic_t. It does some overhead but it should be minute compared to everything else which is going on and the involved cacheline bouncing, so I think it's highly unlikely to cause any noticeable difference. Also, the refcnt in question should be converted to a perpcu_ref for blk-mq anyway, so the atomic_t is likely to go away pretty soon anyway. Thanks. ------- 8< ------- __blkg_release_rcu() may be invoked after the associated request_queue is released with a RCU grace period inbetween. As such, the function and callbacks invoked from it must not dereference the associated request_queue. This is clearly indicated in the comment above the function. Unfortunately, while trying to fix a different issue, 2a4fd070ee85 ("blkcg: move bulk of blkcg_gq release operations to the RCU callback") ignored this and added [un]locking of @blkg->q->queue_lock to __blkg_release_rcu(). This of course can cause oops as the request_queue may be long gone by the time this code gets executed. general protection fault: 0000 [#1] SMP CPU: 21 PID: 30 Comm: rcuos/21 Not tainted 3.15.0 #1 Hardware name: Stratus ftServer 6400/G7LAZ, BIOS BIOS Version 6.3:57 12/25/2013 task: ffff880854021de0 ti: ffff88085403c000 task.ti: ffff88085403c000 RIP: 0010:[<ffffffff8162e9e5>] [<ffffffff8162e9e5>] _raw_spin_lock_irq+0x15/0x60 RSP: 0018:ffff88085403fdf0 EFLAGS: 00010086 RAX: 0000000000020000 RBX: 0000000000000010 RCX: 0000000000000000 RDX: 000060ef80008248 RSI: 0000000000000286 RDI: 6b6b6b6b6b6b6b6b RBP: ffff88085403fdf0 R08: 0000000000000286 R09: 0000000000009f39 R10: 0000000000020001 R11: 0000000000020001 R12: ffff88103c17a130 R13: ffff88103c17a080 R14: 0000000000000000 R15: 0000000000000000 FS: 0000000000000000(0000) GS:ffff88107fca0000(0000) knlGS:0000000000000000 CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033 CR2: 00000000006e5ab8 CR3: 000000000193d000 CR4: 00000000000407e0 Stack: ffff88085403fe18 ffffffff812cbfc2 ffff88103c17a130 0000000000000000 ffff88103c17a130 ffff88085403fec0 ffffffff810d1d28 ffff880854021de0 ffff880854021de0 ffff88107fcaec58 ffff88085403fe80 ffff88107fcaec30 Call Trace: [<ffffffff812cbfc2>] __blkg_release_rcu+0x72/0x150 [<ffffffff810d1d28>] rcu_nocb_kthread+0x1e8/0x300 [<ffffffff81091d81>] kthread+0xe1/0x100 [<ffffffff8163813c>] ret_from_fork+0x7c/0xb0 Code: ff 47 04 48 8b 7d 08 be 00 02 00 00 e8 55 48 a4 ff 5d c3 0f 1f 00 66 66 66 66 90 55 48 89 e5 +fa 66 66 90 66 66 90 b8 00 00 02 00 <f0> 0f c1 07 89 c2 c1 ea 10 66 39 c2 75 02 5d c3 83 e2 fe 0f +b7 RIP [<ffffffff8162e9e5>] _raw_spin_lock_irq+0x15/0x60 RSP <ffff88085403fdf0> The request_queue locking was added because blkcg_gq->refcnt is an int protected with the queue lock and __blkg_release_rcu() needs to put the parent. Let's fix it by making blkcg_gq->refcnt an atomic_t and dropping queue locking in the function. Given the general heavy weight of the current request_queue and blkcg operations, this is unlikely to cause any noticeable overhead. Moreover, blkcg_gq->refcnt is likely to be converted to percpu_ref in the near future, so whatever (most likely negligible) overhead it may add is temporary. Signed-off-by: Tejun Heo <tj@kernel.org> Reported-by: Joe Lawrence <joe.lawrence@stratus.com> Acked-by: Vivek Goyal <vgoyal@redhat.com> Link: http://lkml.kernel.org/g/alpine.DEB.2.02.1406081816540.17948@jlaw-desktop.mno.stratus.com Signed-off-by: Jens Axboe <axboe@fb.com> Signed-off-by: Jiri Slaby <jslaby@suse.cz>
2014-07-18CIFS: fix mount failure with broken pathnames when smb3 mount with mapchars ↵Steve French
option commit ce36d9ab3bab06b7b5522f5c8b68fac231b76ffb upstream. When we SMB3 mounted with mapchars (to allow reserved characters : \ / > < * ? via the Unicode Windows to POSIX remap range) empty paths (eg when we open "" to query the root of the SMB3 directory on mount) were not null terminated so we sent garbarge as a path name on empty paths which caused SMB2/SMB2.1/SMB3 mounts to fail when mapchars was specified. mapchars is particularly important since Unix Extensions for SMB3 are not supported (yet) Signed-off-by: Steve French <smfrench@gmail.com> Reviewed-by: David Disseldorp <ddiss@suse.de> Signed-off-by: Jiri Slaby <jslaby@suse.cz>
2014-07-18b43: fix frequency reported on G-PHY with /new/ firmwareRafał Miłecki
commit 2fc68eb122c7ea6cd5be1fe7d6650c0beb2f4f40 upstream. Support for firmware rev 508+ was added years ago, but we never noticed it reports channel in a different way for G-PHY devices. Instead of offset from 2400 MHz it simply passes channel id (AKA hw_value). So far it was (most probably) affecting monitor mode users only, but the following recent commit made it noticeable for quite everybody: commit 3afc2167f60a327a2c1e1e2600ef209a3c2b75b7 Author: Emmanuel Grumbach <emmanuel.grumbach@intel.com> Date: Tue Mar 4 16:50:13 2014 +0200 cfg80211/mac80211: ignore signal if the frame was heard on wrong channel Reported-by: Aaro Koskinen <aaro.koskinen@iki.fi> Signed-off-by: Rafał Miłecki <zajec5@gmail.com> Tested-by: Aaro Koskinen <aaro.koskinen@iki.fi> Signed-off-by: John W. Linville <linville@tuxdriver.com> Signed-off-by: Jiri Slaby <jslaby@suse.cz>
2014-07-18net: allwinner: emac: Add missing free_irqMaxime Ripard
commit b91113282bf44df46aba374a0b8f88a75bfd4b3f upstream. If the mdio probe function fails in emac_open, the interrupt we just requested isn't freed. If emac_open is called again, for example because we try to set up the interface again, the kernel will oops because the interrupt wasn't properly released. Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Jiri Slaby <jslaby@suse.cz>
2014-07-18arm64: Bug fix in stack alignment exceptionChiaHao
commit 3906c2b53cd23c2ae03e6ce41432c8e7f0a3cbbb upstream. The value of ESR has been stored into x1, and should be directly pass to do_sp_pc_abort function, "MOV x1, x25" is an extra operation and do_sp_pc_abort will get the wrong value of ESR. Signed-off-by: ChiaHao <andy.jhshiu@gmail.com> Signed-off-by: Catalin Marinas <catalin.marinas@arm.com> Cc: <stable@vger.kernel.org> Signed-off-by: Jiri Slaby <jslaby@suse.cz>
2014-07-18ARM: OMAP2+: Fix parser-bug in platform muxing codeDavid R. Piegdon
commit c021f241f4fab2bb4fc4120a38a828a03dd3f970 upstream. Fix a parser-bug in the omap2 muxing code where muxtable-entries will be wrongly selected if the requested muxname is a *prefix* of their m0-entry and they have a matching mN-entry. Fix by additionally checking that the length of the m0_entry is equal. For example muxing of "dss_data2.dss_data2" on omap32xx will fail because the prefix "dss_data2" will match the mux-entries "dss_data2" as well as "dss_data20", with the suffix "dss_data2" matching m0 (for dss_data2) and m4 (for dss_data20). Thus both are recognized as signal path candidates: Relevant muxentries from mux34xx.c: _OMAP3_MUXENTRY(DSS_DATA20, 90, "dss_data20", NULL, "mcspi3_somi", "dss_data2", "gpio_90", NULL, NULL, "safe_mode"), _OMAP3_MUXENTRY(DSS_DATA2, 72, "dss_data2", NULL, NULL, NULL, "gpio_72", NULL, NULL, "safe_mode"), This will result in a failure to mux the pin at all: _omap_mux_get_by_name: Multiple signal paths (2) for dss_data2.dss_data2 Patch should apply to linus' latest master down to rather old linux-2.6 trees. Signed-off-by: David R. Piegdon <lkml@p23q.org> Cc: stable@vger.kernel.org [tony@atomide.com: updated description to include full description] Signed-off-by: Tony Lindgren <tony@atomide.com> Signed-off-by: Jiri Slaby <jslaby@suse.cz>
2014-07-18arm64: mm: Make icache synchronisation logic huge page awareSteve Capper
commit 923b8f5044da753e4985ab15c1374ced2cdf616c upstream. The __sync_icache_dcache routine will only flush the dcache for the first page of a compound page, potentially leading to stale icache data residing further on in a hugetlb page. This patch addresses this issue by taking into consideration the order of the page when flushing the dcache. Reported-by: Mark Brown <broonie@linaro.org> Tested-by: Mark Brown <broonie@linaro.org> Signed-off-by: Steve Capper <steve.capper@linaro.org> Acked-by: Will Deacon <will.deacon@arm.com> Signed-off-by: Catalin Marinas <catalin.marinas@arm.com> Signed-off-by: Jiri Slaby <jslaby@suse.cz>
2014-07-18mm, pcp: allow restoring percpu_pagelist_fraction defaultDavid Rientjes
commit 7cd2b0a34ab8e4db971920eef8982f985441adfb upstream. Oleg reports a division by zero error on zero-length write() to the percpu_pagelist_fraction sysctl: divide error: 0000 [#1] SMP DEBUG_PAGEALLOC CPU: 1 PID: 9142 Comm: badarea_io Not tainted 3.15.0-rc2-vm-nfs+ #19 Hardware name: Bochs Bochs, BIOS Bochs 01/01/2011 task: ffff8800d5aeb6e0 ti: ffff8800d87a2000 task.ti: ffff8800d87a2000 RIP: 0010: percpu_pagelist_fraction_sysctl_handler+0x84/0x120 RSP: 0018:ffff8800d87a3e78 EFLAGS: 00010246 RAX: 0000000000000f89 RBX: ffff88011f7fd000 RCX: 0000000000000000 RDX: 0000000000000000 RSI: 0000000000000001 RDI: 0000000000000010 RBP: ffff8800d87a3e98 R08: ffffffff81d002c8 R09: ffff8800d87a3f50 R10: 000000000000000b R11: 0000000000000246 R12: 0000000000000060 R13: ffffffff81c3c3e0 R14: ffffffff81cfddf8 R15: ffff8801193b0800 FS: 00007f614f1e9740(0000) GS:ffff88011f440000(0000) knlGS:0000000000000000 CS: 0010 DS: 0000 ES: 0000 CR0: 000000008005003b CR2: 00007f614f1fa000 CR3: 00000000d9291000 CR4: 00000000000006e0 Call Trace: proc_sys_call_handler+0xb3/0xc0 proc_sys_write+0x14/0x20 vfs_write+0xba/0x1e0 SyS_write+0x46/0xb0 tracesys+0xe1/0xe6 However, if the percpu_pagelist_fraction sysctl is set by the user, it is also impossible to restore it to the kernel default since the user cannot write 0 to the sysctl. This patch allows the user to write 0 to restore the default behavior. It still requires a fraction equal to or larger than 8, however, as stated by the documentation for sanity. If a value in the range [1, 7] is written, the sysctl will return EINVAL. This successfully solves the divide by zero issue at the same time. Signed-off-by: David Rientjes <rientjes@google.com> Reported-by: Oleg Drokin <green@linuxhacker.ru> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org> Signed-off-by: Jiri Slaby <jslaby@suse.cz>
2014-07-17iwlwifi: pcie: try to get ownership several timesEmmanuel Grumbach
commit 501fd9895c1d7d8161ed56698ae2fccb10ef14f5 upstream. Some races with the hardware can happen when we take ownership of the device. Don't give up after the first try. Reviewed-by: Johannes Berg <johannes.berg@intel.com> Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com> Signed-off-by: Jiri Slaby <jslaby@suse.cz>
2014-07-17mac80211: fix a memory leak on sta rate selection tableFelix Fietkau
commit 53d045258ee2e38b1e882617cb0799a04d05f5fa upstream. If the rate control algorithm uses a selection table, it is leaked when the station is destroyed - fix that. Signed-off-by: Felix Fietkau <nbd@openwrt.org> Reported-by: Christophe Prévotaux <cprevotaux@nltinc.com> Fixes: 0d528d85c519 ("mac80211: improve the rate control API") [add commit log entry, remove pointless NULL check] Signed-off-by: Johannes Berg <johannes.berg@intel.com> Signed-off-by: Jiri Slaby <jslaby@suse.cz>
2014-07-17mac80211: don't check netdev state for debugfs read/writeArik Nemtsov
commit 923eaf367206e01f22c97aee22300e332d071916 upstream. Doing so will lead to an oops for a p2p-dev interface, since it has no netdev. Signed-off-by: Arik Nemtsov <arikx.nemtsov@intel.com> Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com> Signed-off-by: Johannes Berg <johannes.berg@intel.com> Signed-off-by: Jiri Slaby <jslaby@suse.cz>
2014-07-17mac80211: fix IBSS join by initializing last_scan_completedKrzysztof Hałasa
commit c7d37a66e345df2fdf1aa7b2c9a6d3d53846ca5b upstream. Without this fix, freshly rebooted Linux creates a new IBSS instead of joining an existing one. Only when jiffies counter overflows after 5 minutes the IBSS can be successfully joined. Signed-off-by: Krzysztof Hałasa <khalasa@piap.pl> [edit commit message slightly] Signed-off-by: Johannes Berg <johannes.berg@intel.com> Signed-off-by: Jiri Slaby <jslaby@suse.cz>
2014-07-17hwmon: (ina2xx) Cast to s16 on shunt and current regsFabio Baltieri
commit c0214f98943b1fe43f7be61b7782b0c8f0836f28 upstream. All devices supported by ina2xx are bidirectional and report the measured shunt voltage and power values as a signed 16 bit, but the current driver implementation caches all registers as u16, leading to an incorrect sign extension when reporting to userspace in ina2xx_get_value(). This patch fixes the problem by casting the signed registers to s16. Tested on an INA219. Signed-off-by: Fabio Baltieri <fabio.baltieri@gmail.com> Signed-off-by: Guenter Roeck <linux@roeck-us.net> Signed-off-by: Jiri Slaby <jslaby@suse.cz>
2014-07-17rbd: handle parent_overlap on writes correctlyIlya Dryomov
commit 9638556a276125553549fdfe349c464481ec2f39 upstream. The following check in rbd_img_obj_request_submit() rbd_dev->parent_overlap <= obj_request->img_offset allows the fall through to the non-layered write case even if both parent_overlap and obj_request->img_offset belong to the same RADOS object. This leads to data corruption, because the area to the left of parent_overlap ends up unconditionally zero-filled instead of being populated with parent data. Suppose we want to write 1M to offset 6M of image bar, which is a clone of foo@snap; object_size is 4M, parent_overlap is 5M: rbd_data.<id>.0000000000000001 ---------------------|----------------------|------------ | should be copyup'ed | should be zeroed out | write ... ---------------------|----------------------|------------ 4M 5M 6M parent_overlap obj_request->img_offset 4..5M should be copyup'ed from foo, yet it is zero-filled, just like 5..6M is. Given that the only striping mode kernel client currently supports is chunking (i.e. stripe_unit == object_size, stripe_count == 1), round parent_overlap up to the next object boundary for the purposes of the overlap check. Signed-off-by: Ilya Dryomov <ilya.dryomov@inktank.com> Reviewed-by: Josh Durgin <josh.durgin@inktank.com> Signed-off-by: Jiri Slaby <jslaby@suse.cz>
2014-07-17rbd: use reference counts for image requestsAlex Elder
commit 0f2d5be792b0466b06797f637cfbb0f64dbb408c upstream. Each image request contains a reference count, but to date it has not actually been used. (I think this was just an oversight.) A recent report involving rbd failing an assertion shed light on why and where we need to use these reference counts. Every OSD request associated with an object request uses rbd_osd_req_callback() as its callback function. That function will call a helper function (dependent on the type of OSD request) that will set the object request's "done" flag if the object request if appropriate. If that "done" flag is set, the object request is passed to rbd_obj_request_complete(). In rbd_obj_request_complete(), requests are processed in sequential order. So if an object request completes before one of its predecessors in the image request, the completion is deferred. Otherwise, if it's a completing object's "turn" to be completed, it is passed to rbd_img_obj_end_request(), which records the result of the operation, accumulates transferred bytes, and so on. Next, the successor to this request is checked and if it is marked "done", (deferred) completion processing is performed on that request, and so on. If the last object request in an image request is completed, rbd_img_request_complete() is called, which (typically) destroys the image request. There is a race here, however. The instant an object request is marked "done" it can be provided (by a thread handling completion of one of its predecessor operations) to rbd_img_obj_end_request(), which (for the last request) can then lead to the image request getting torn down. And this can happen *before* that object has itself entered rbd_img_obj_end_request(). As a result, once it *does* enter that function, the image request (and even the object request itself) may have been freed and become invalid. All that's necessary to avoid this is to properly count references to the image requests. We tear down an image request's object requests all at once--only when the entire image request has completed. So there's no need for an image request to count references for its object requests. However, we don't want an image request to go away until the last of its object requests has passed through rbd_img_obj_callback(). In other words, we don't want rbd_img_request_complete() to necessarily result in the image request being destroyed, because it may get called before we've finished processing on all of its object requests. So the fix is to add a reference to an image request for each of its object requests. The reference can be viewed as representing an object request that has not yet finished its call to rbd_img_obj_callback(). That is emphasized by getting the reference right after assigning that as the image object's callback function. The corresponding release of that reference is done at the end of rbd_img_obj_callback(), which every image object request passes through exactly once. Signed-off-by: Alex Elder <elder@linaro.org> Reviewed-by: Ilya Dryomov <ilya.dryomov@inktank.com> Signed-off-by: Jiri Slaby <jslaby@suse.cz>
2014-07-17dm thin: update discard_granularity to reflect the thin-pool blocksizeLukas Czerner
commit 09869de57ed2728ae3c619803932a86cb0e2c4f8 upstream. DM thinp already checks whether the discard_granularity of the data device is a factor of the thin-pool block size. But when using the dm-thin-pool's discard passdown support, DM thinp was not selecting the max of the underlying data device's discard_granularity and the thin-pool's block size. Update set_discard_limits() to set discard_granularity to the max of these values. This enables blkdev_issue_discard() to properly align the discards that are sent to the DM thin device on a full block boundary. As such each discard will now cover an entire DM thin-pool block and the block will be reclaimed. Reported-by: Zdenek Kabelac <zkabelac@redhat.com> Signed-off-by: Lukas Czerner <lczerner@redhat.com> Signed-off-by: Mike Snitzer <snitzer@redhat.com> Signed-off-by: Jiri Slaby <jslaby@suse.cz>
2014-07-17Bluetooth: Allow change security level on ATT_CID in slave roleMarcin Kraglak
commit 92d1372e1a9fec00e146b74e8b9ad7a385b9b37f upstream. Kernel supports SMP Security Request so don't block increasing security when we are slave. Signed-off-by: Marcin Kraglak <marcin.kraglak@tieto.com> Acked-by: Johan Hedberg <johan.hedberg@intel.com> Signed-off-by: Marcel Holtmann <marcel@holtmann.org> Signed-off-by: Jiri Slaby <jslaby@suse.cz>
2014-07-17Bluetooth: Fix locking of hdev when calling into SMP codeJohan Hedberg
commit c73f94b8c093a615ce80eabbde0ac6eb9abfe31a upstream. The SMP code expects hdev to be unlocked since e.g. crypto functions will try to (re)lock it. Therefore, we need to release the lock before calling into smp.c from mgmt.c. Without this we risk a deadlock whenever the smp_user_confirm_reply() function is called. Signed-off-by: Johan Hedberg <johan.hedberg@intel.com> Tested-by: Lukasz Rymanowski <lukasz.rymanowski@tieto.com> Signed-off-by: Marcel Holtmann <marcel@holtmann.org> Signed-off-by: Jiri Slaby <jslaby@suse.cz>
2014-07-17Bluetooth: Fix indicating discovery state when canceling inquiryJohan Hedberg
commit 50143a433b70e3145bcf8a4a4e54f0c11bdee32b upstream. When inquiry is canceled through the HCI_Cancel_Inquiry command there is no Inquiry Complete event generated. Instead, all we get is the command complete for the HCI_Inquiry_Cancel command. This means that we must call the hci_discovery_set_state() function from the respective command complete handler in order to ensure that user space knows the correct discovery state. Signed-off-by: Johan Hedberg <johan.hedberg@intel.com> Signed-off-by: Marcel Holtmann <marcel@holtmann.org> Signed-off-by: Jiri Slaby <jslaby@suse.cz>
2014-07-17Bluetooth: Fix SSP acceptor just-works confirmation without MITMJohan Hedberg
commit ba15a58b179ed76a7e887177f2b06de12c58ec8f upstream. From the Bluetooth Core Specification 4.1 page 1958: "if both devices have set the Authentication_Requirements parameter to one of the MITM Protection Not Required options, authentication stage 1 shall function as if both devices set their IO capabilities to DisplayOnly (e.g., Numeric comparison with automatic confirmation on both devices)" So far our implementation has done user confirmation for all just-works cases regardless of the MITM requirements, however following the specification to the word means that we should not be doing confirmation when neither side has the MITM flag set. Signed-off-by: Johan Hedberg <johan.hedberg@intel.com> Tested-by: Szymon Janc <szymon.janc@tieto.com> Signed-off-by: Marcel Holtmann <marcel@holtmann.org> Signed-off-by: Jiri Slaby <jslaby@suse.cz>
2014-07-17drm/vmwgfx: Fix incorrect write to read-only register v2:Thomas Hellstrom
commit 4e578080ed3262ed2c3985868539bc66218d25c0 upstream. Commit "drm/vmwgfx: correct fb_fix_screeninfo.line_length", while fixing a vmwgfx fbdev bug, also writes the pitch to a supposedly read-only register: SVGA_REG_BYTES_PER_LINE, while it should be (and also in fact is) written to SVGA_REG_PITCHLOCK. This patch is Cc'd stable because of the unknown effects writing to this register might have, particularly on older device versions. v2: Updated log message. Cc: Christopher Friedt <chrisfriedt@gmail.com> Tested-by: Christopher Friedt <chrisfriedt@gmail.com> Signed-off-by: Thomas Hellstrom <thellstrom@vmware.com> Reviewed-by: Jakob Bornecrantz <jakob@vmware.com> Signed-off-by: Jiri Slaby <jslaby@suse.cz>
2014-07-17drm/radeon/cik: fix typo in EOP packetAlex Deucher
commit b397207b7475afa9df2f94541f978100ff1ea47e upstream. Volatile bit was in the wrong location. This bit is not used at the moment. Signed-off-by: Alex Deucher <alexander.deucher@amd.com> Signed-off-by: Jiri Slaby <jslaby@suse.cz>
2014-07-17drm/radeon/dpm: fix vddci setup typo on caymanAlex Deucher
commit b0880e87c1fd038b84498944f52e52c3e86ebe59 upstream. We were using the vddc mask rather than the vddci mask. Bug: https://bugzilla.kernel.org/show_bug.cgi?id=79071 May also fix: https://bugs.freedesktop.org/show_bug.cgi?id=69723 Noticed by: Dieter Nützel <Dieter@nuetzel-hh.de> Signed-off-by: Alex Deucher <alexander.deucher@amd.com> Signed-off-by: Jiri Slaby <jslaby@suse.cz>
2014-07-17drm/radeon/dpm: fix typo in vddci setup for eg/btcAlex Deucher
commit e07929810f0a19ddd756558290c7d72827cbfcd9 upstream. We were using the vddc mask rather than the vddci mask. Bug: https://bugzilla.kernel.org/show_bug.cgi?id=79071 Possibly also fixes: https://bugzilla.kernel.org/show_bug.cgi?id=68571 Noticed-by: Jonathan Howard <jonathan@unbiased.name> Signed-off-by: Alex Deucher <alexander.deucher@amd.com> Signed-off-by: Jiri Slaby <jslaby@suse.cz>
2014-07-17drm/radeon: don't allow RADEON_GEM_DOMAIN_CPU for command submissionMarek Olšák
commit ec65da385d46f63740c1c9230b891a6dcbd64c71 upstream. It hangs the hardware. Signed-off-by: Marek Olšák <marek.olsak@amd.com> Reviewed-by: Christian König <christian.koenig@amd.com> Signed-off-by: Jiri Slaby <jslaby@suse.cz>
2014-07-17drm/radeon/atom: fix dithering on certain panelsAlex Deucher
commit 642528355c694f5ed68f6bff9ff520326a249f99 upstream. We need to specify the encoder mode as LVDS for eDP when using the Crtc_Source atom table in order to properly set up the FMT hardware. bug: https://bugs.freedesktop.org/show_bug.cgi?id=73911 Signed-off-by: Alex Deucher <alexander.deucher@amd.com> Signed-off-by: Jiri Slaby <jslaby@suse.cz>
2014-07-17drm/radeon/dp: fix lane/clock setup for dp 1.2 capable devicesAlex Deucher
commit 3b6d9fd23e015b5397c438fd3cd74147d2c805b6 upstream. Only DCE5+ asics support DP 1.2. Noticed by ArtForz on IRC. Signed-off-by: Alex Deucher <alexander.deucher@amd.com> Signed-off-by: Jiri Slaby <jslaby@suse.cz>
2014-07-17drm/radeon: fix typo in radeon_connector_is_dp12_capable()Alex Deucher
commit af5d36539dfe043f1cf0f8b7334d6bb12cd14e75 upstream. We were checking the ext clock rather than the display clock. Noticed by ArtForz on IRC. Signed-off-by: Alex Deucher <alexander.deucher@amd.com> Signed-off-by: Jiri Slaby <jslaby@suse.cz>
2014-07-17drm/radeon: only apply hdmi bpc pll flags when encoder mode is hdmiAlex Deucher
commit 7d5ab3009a8ca777174f6f469277b3922d56fd4b upstream. May fix display issues with non-HDMI displays. Signed-off-by: Alex Deucher <alexander.deucher@amd.com> Signed-off-by: Jiri Slaby <jslaby@suse.cz>
2014-07-17vgaswitcheroo: switch the mux to the igp on power down when runpm is enabledAlex Deucher
commit f2bc561610962693be61425cf913778586d8f9c1 upstream. Avoids blank screens on muxed systems when runpm is active. bug: https://bugs.freedesktop.org/show_bug.cgi?id=75917 Signed-off-by: Alex Deucher <alexander.deucher@amd.com> Signed-off-by: Jiri Slaby <jslaby@suse.cz>
2014-07-17mtd: nand: omap: fix BCHx ecc.correct to return detected bit-flips in ↵pekon gupta
erased-page commit f306e8c3b667632952f1a4a74ffb910bbc06255f upstream. fixes: commit 62116e5171e00f85a8d53f76e45b84423c89ff34 mtd: nand: omap2: Support for hardware BCH error correction. In omap_elm_correct_data(), if bitflip_count in an erased-page is within the correctable limit (< ecc.strength), then it is not indicated back to the caller ecc->read_page(). This mis-guides upper layers like MTD and UBIFS layer to assume erased-page as perfectly clean and use it for writing even if actual bitflip_count was dangerously high (bitflip_count > mtd->bitflip_threshold). This patch fixes this above issue, by returning 'stats' to caller ecc->read_page() under all scenarios. Reported-by: Brian Norris <computersforpeace@gmail.com> Signed-off-by: Pekon Gupta <pekon@ti.com> Signed-off-by: Brian Norris <computersforpeace@gmail.com> Signed-off-by: Jiri Slaby <jslaby@suse.cz>
2014-07-17mtd: eLBC NAND: fix subpage write supportPekon Gupta
commit f034d87def51f026b735d1e2877e9387011b2ba3 upstream. As subpage write is enabled by default for all drivers, nand_write_subpage_hwecc causes a crash if the driver did not register ecc->hwctl or ecc->calculate. This behavior was introduced in commit 837a6ba4f3b6d23026674e6af6b6849a4634fff9 "mtd: nand: subpage write support for hardware based ECC schemes". This fixes a crash by emulating subpage write support by padding sub-page data with 0xff on either sides to make it full page compatible. Reported-by: Helmut Schaa <helmut.schaa@googlemail.com> Tested-by: Helmut Schaa <helmut.schaa@googlemail.com> Signed-off-by: Pekon Gupta <pekon@ti.com> Reviewed-by: Scott Wood <scottwood@freescale.com> Signed-off-by: Brian Norris <computersforpeace@gmail.com> Signed-off-by: Jiri Slaby <jslaby@suse.cz>
2014-07-17rt2x00: fix rfkill regression on rt2500pciStanislaw Gruszka
commit 616a8394b5df8c88f4dd416f4527439a4e365034 upstream. As reported by Niels, starting rfkill polling during device probe (commit e2bc7c5, generally sane change) broke rfkill on rt2500pci device. I considered that bug as some initalization issue, which should be fixed on rt2500pci specific code. But after several attempts (see bug report for details) we fail to find working solution. Hence I decided to revert to old behaviour on rt2500pci to fix regression. Additionally patch also unregister rfkill on device remove instead of ifconfig down, what was another issue introduced by bad commit. Bug report: https://bugzilla.kernel.org/show_bug.cgi?id=73821 Fixes: e2bc7c5f3cb8 ("rt2x00: Fix rfkill_polling register function.") Bisected-by: Niels <nille0386@googlemail.com> Reported-and-tested-by: Niels <nille0386@googlemail.com> Signed-off-by: Stanislaw Gruszka <stf_xl@wp.pl> Signed-off-by: John W. Linville <linville@tuxdriver.com> Signed-off-by: Jiri Slaby <jslaby@suse.cz>
2014-07-17rt2x00: disable TKIP on USBStanislaw Gruszka
commit 8edcb0ba0d56f5914eef11eda6db8bfe74eb9ca8 upstream. On USB we can not get atomically TKIP key. We have to disable support for TKIP acceleration on USB hardware to avoid bug as showed bellow. [ 860.827243] BUG: scheduling while atomic: hostapd/3397/0x00000002 <snip> [ 860.827280] Call Trace: [ 860.827282] [<ffffffff81682ea6>] dump_stack+0x4d/0x66 [ 860.827284] [<ffffffff8167eb9b>] __schedule_bug+0x47/0x55 [ 860.827285] [<ffffffff81685bb3>] __schedule+0x733/0x7b0 [ 860.827287] [<ffffffff81685c59>] schedule+0x29/0x70 [ 860.827289] [<ffffffff81684f8a>] schedule_timeout+0x15a/0x2b0 [ 860.827291] [<ffffffff8105ac50>] ? ftrace_raw_event_tick_stop+0xc0/0xc0 [ 860.827294] [<ffffffff810c13c2>] ? __module_text_address+0x12/0x70 [ 860.827296] [<ffffffff81686823>] wait_for_completion_timeout+0xb3/0x140 [ 860.827298] [<ffffffff81080fc0>] ? wake_up_state+0x20/0x20 [ 860.827301] [<ffffffff814d5b3d>] usb_start_wait_urb+0x7d/0x150 [ 860.827303] [<ffffffff814d5cd5>] usb_control_msg+0xc5/0x110 [ 860.827305] [<ffffffffa02fb0c6>] rt2x00usb_vendor_request+0xc6/0x160 [rt2x00usb] [ 860.827307] [<ffffffffa02fb215>] rt2x00usb_vendor_req_buff_lock+0x75/0x150 [rt2x00usb] [ 860.827309] [<ffffffffa02fb393>] rt2x00usb_vendor_request_buff+0xa3/0xe0 [rt2x00usb] [ 860.827311] [<ffffffffa023d1a3>] rt2x00usb_register_multiread+0x33/0x40 [rt2800usb] [ 860.827314] [<ffffffffa05805f9>] rt2800_get_tkip_seq+0x39/0x50 [rt2800lib] [ 860.827321] [<ffffffffa0480f88>] ieee80211_get_key+0x218/0x2a0 [mac80211] [ 860.827322] [<ffffffff815cc68c>] ? __nlmsg_put+0x6c/0x80 [ 860.827329] [<ffffffffa051b02e>] nl80211_get_key+0x22e/0x360 [cfg80211] Reported-and-tested-by: Peter Wu <lekensteyn@gmail.com> Reported-and-tested-by: Pontus Fuchs <pontus.fuchs@gmail.com> Signed-off-by: Stanislaw Gruszka <sgruszka@redhat.com> Signed-off-by: John W. Linville <linville@tuxdriver.com> Signed-off-by: Jiri Slaby <jslaby@suse.cz>
2014-07-17usb: gadget: f_fs: fix NULL pointer dereference when there are no stringsMichal Nazarewicz
commit f0688c8b81d2ea239c3fb0b848f623b579238d99 upstream. If the descriptors do not need any strings and user space sends empty set of strings, the ffs->stringtabs field remains NULL. Thus *ffs->stringtabs in functionfs_bind leads to a NULL pointer dereferenece. The bug was introduced by commit [fd7c9a007f: “use usb_string_ids_n()”]. While at it, remove double initialisation of lang local variable in that function. ffs->strings_count does not need to be checked in any way since in the above scenario it will remain zero and usb_string_ids_n() is a no-operation when colled with 0 argument. Signed-off-by: Michal Nazarewicz <mina86@mina86.com> Signed-off-by: Felipe Balbi <balbi@ti.com> Signed-off-by: Jiri Slaby <jslaby@suse.cz>
2014-07-17USB: ftdi_sio: fix null deref at port probeJohan Hovold
commit aea1ae8760314e072bf1b773521e9de5d5dda10d upstream. Fix NULL-pointer dereference when probing an interface with no endpoints. These devices have two bulk endpoints per interface, but this avoids crashing the kernel if a user forces a non-FTDI device to be probed. Note that the iterator variable was made unsigned in order to avoid a maybe-uninitialized compiler warning for ep_desc after the loop. Fixes: 895f28badce9 ("USB: ftdi_sio: fix hi-speed device packet size calculation") Reported-by: Mike Remski <mremski@mutualink.net> Tested-by: Mike Remski <mremski@mutualink.net> Signed-off-by: Johan Hovold <johan@kernel.org> Signed-off-by: Jiri Slaby <jslaby@suse.cz>
2014-07-17usb: chipidea: udc: delete td from req's td list at ep_dequeuePeter Chen
commit e4adcff09ca39ecbcc4851d40d0f0a5458e7b77a upstream. We need to delete un-finished td from current request's td list at ep_dequeue API, otherwise, this non-user td will be remained at td list before this request is freed. So if we do ep_queue-> ep_dequeue->ep_queue sequence, when the complete interrupt for the second ep_queue comes, we search td list for this request, the first td (added by the first ep_queue) will be handled, and its status is still active, so we will consider the this transfer still not be completed, but in fact, it has completed. It causes the peripheral side considers it never receives current data for this transfer. We met this problem when do "Error Recovery Test - Device Configured" test item for USBCV2 MSC test, the host has never received ACK for the IN token for CSW due to peripheral considers it does not get this CBW, the USBCV test log like belows: -------------------------------------------------------------------------- INFO Issuing BOT MSC Reset, reset should always succeed INFO Retrieving status on CBW endpoint INFO CBW endpoint status = 0x0 INFO Retrieving status on CSW endpoint INFO CSW endpoint status = 0x0 INFO Issuing required command (Test Unit Ready) to verify device has recovered INFO Issuing CBW (attempt #1): INFO |----- CBW LUN = 0x0 INFO |----- CBW Flags = 0x0 INFO |----- CBW Data Transfer Length = 0x0 INFO |----- CBW CDB Length = 0x6 INFO |----- CBW CDB-00 = 0x0 INFO |----- CBW CDB-01 = 0x0 INFO |----- CBW CDB-02 = 0x0 INFO |----- CBW CDB-03 = 0x0 INFO |----- CBW CDB-04 = 0x0 INFO |----- CBW CDB-05 = 0x0 INFO Issuing CSW : try 1 INFO CSW Bulk Request timed out! ERROR Failed CSW phase : should have been success or stall FAIL (5.3.4) The CSW status value must be 0x00, 0x01, or 0x02. ERROR BOTCommonMSCRequest failed: error=80004000 Cc: Andrzej Pietrasiewicz <andrzej.p@samsung.com> Signed-off-by: Peter Chen <peter.chen@freescale.com> Signed-off-by: Jiri Slaby <jslaby@suse.cz>
generated by cgit v1.2.3 (git 2.0.4) at 2026-10-16 15:49:43 +0000