| Age | Commit message (Collapse) | Author |
|---|
|
So qxl has ioports, but it really really really doesn't want you
to write to them twice, but if you write and get a signal before
the irq arrives to let you know its completed, you have to think
ahead and avoid writing another time.
However this works fine for update area where really multiple
writes aren't the end of the world, however with create primary
surface, you can't ever do multiple writes. So this stop internal
kernel writes from doing interruptible waits, because otherwise
we have no idea if this write is a new one or a continuation of
a previous one.
virtual hw sucks more than real hw.
This fixes lockups and VM crashes when resizing and starting/stopping
X.
Signed-off-by: Dave Airlie <airlied@redhat.com>
|
|
We don't use these anymore so nuke them.
Signed-off-by: Dave Airlie <airlied@redhat.com>
|
|
The "boxes" parameter points into userspace memory. It should be verified
like any other operation against user memory.
Signed-off-by: Kees Cook <keescook@chromium.org>
Cc: stable@vger.kernel.org
Signed-off-by: Dave Airlie <airlied@redhat.com>
|
|
Higher bits of the base address of framebuffers weren't being
programmed properly. This caused framebuffers that didn't happen to be
allocated at a low enough address to not be displayed properly.
Signed-off-by: Christopher Harvey <charvey@matrox.com>
Signed-off-by: Mathieu Larouche <mathieu.larouche@matrox.com>
Acked-by: Julia Lemire <jlemire@matrox.com>
Tested-by: Julia Lemire <jlemire@matrox.com>
Cc: stable@vger.kernel.org
Signed-off-by: Dave Airlie <airlied@redhat.com>
|
|
Signed-off-by: Christopher Harvey <charvey@matrox.com>
Acked-by: Julia Lemire <jlemire@matrox.com>
Tested-by: Julia Lemire <jlemire@matrox.com>
Acked-by: Mathieu Larouche <mathieu.larouche@matrox.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
|
|
The original line,
WREG_DAC(MGA1064_PIX_CLK_CTL_CLK_DIS, tmp);
wrote tmp into MGA1064_PIX_CLK_CTL_CLK_DIS, where
MGA1064_PIX_CLK_CTL_CLK_DIS is an offset into
MGA1064_PIX_CLK_CTL. Change the line to write properly into
MGA1064_PIX_CLK_CTL. There were other chunks of code nearby that use
the same pattern (but work correctly), so this patch updates them all
to use this new (slightly more efficient) write pattern. The WREG_DAC
macro was causing the DAC_INDEX register to be set to the same value
twice. WREG8(DAC_DATA, foo) takes advantage of the fact that DAC_INDEX
is already at the value we want.
Signed-off-by: Christopher Harvey <charvey@matrox.com>
Acked-by: Julia Lemire <jlemire@matrox.com>
Tested-by: Julia Lemire <jlemire@matrox.com>
Acked-by: Mathieu Larouche <mathieu.larouche@matrox.com>
Cc: stable@vger.kernel.org
Signed-off-by: Dave Airlie <airlied@redhat.com>
|
|
Registers in indices below 0x18 are totally unrelated to modesetting,
so don't write 0's, or anything else into them on modeset. Most of
these registers are hardware cursor related, so this existing code
interferes with hardware cursor development.
Signed-off-by: Christopher Harvey <charvey@matrox.com>
Tested-by: Julia Lemire <jlemire@matrox.com>
Acked-by: Julia Lemire <jlemire@matrox.com>
Acked-by: Mathieu Larouche <mathieu.larouche@matrox.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
|
|
Suggested-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Damien Lespiau <damien.lespiau@intel.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
|
|
Instead of just printing "status updated from 1 to 2", make those enum
numbers immediately readable.
v2: Also patch output_poll_execute() (Daniel Vetter)
v3: Use drm_get_connector_status_name (Ville Syrjälä)
Signed-off-by: Damien Lespiau <damien.lespiau@intel.com>
Reviewed-by: Jesse Barnes <jbarnes@virtuousgeek.org> (for v1)
Signed-off-by: Dave Airlie <airlied@redhat.com>
|
|
The intention here is to make the output of dmesg with full verbosity a
bit easier for a human to parse. This commit transforms:
[drm:drm_ioctl], pid=699, cmd=0x6458, nr=0x58, dev 0xe200, auth=1
[drm:drm_ioctl], pid=699, cmd=0xc010645b, nr=0x5b, dev 0xe200, auth=1
[drm:drm_ioctl], pid=699, cmd=0xc0106461, nr=0x61, dev 0xe200, auth=1
[drm:drm_ioctl], pid=699, cmd=0xc01c64ae, nr=0xae, dev 0xe200, auth=1
[drm:drm_mode_addfb], [FB:32]
[drm:drm_ioctl], pid=699, cmd=0xc0106464, nr=0x64, dev 0xe200, auth=1
[drm:drm_vm_open_locked], 0x7fd9302fe000,0x00a00000
[drm:drm_ioctl], pid=699, cmd=0x400c645f, nr=0x5f, dev 0xe200, auth=1
[drm:drm_ioctl], pid=699, cmd=0xc00464af, nr=0xaf, dev 0xe200, auth=1
[drm:intel_crtc_set_config], [CRTC:3] [NOFB]
into:
[drm:drm_ioctl], pid=699, dev=0xe200, auth=1, I915_GEM_THROTTLE
[drm:drm_ioctl], pid=699, dev=0xe200, auth=1, I915_GEM_CREATE
[drm:drm_ioctl], pid=699, dev=0xe200, auth=1, I915_GEM_SET_TILING
[drm:drm_ioctl], pid=699, dev=0xe200, auth=1, IOCTL_MODE_ADDFB
[drm:drm_mode_addfb], [FB:32]
[drm:drm_ioctl], pid=699, dev=0xe200, auth=1, I915_GEM_MMAP_GTT
[drm:drm_vm_open_locked], 0x7fd9302fe000,0x00a00000
[drm:drm_ioctl], pid=699, dev=0xe200, auth=1, I915_GEM_SET_DOMAIN
[drm:drm_ioctl], pid=699, dev=0xe200, auth=1, DRM_IOCTL_MODE_RMFB
[drm:intel_crtc_set_config], [CRTC:3] [NOFB]
v2: drm_ioctls is now a constant (Ville Syrjälä)
Signed-off-by: Chris Cummins <christopher.e.cummins@intel.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
|
|
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
|
|
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
|
|
This reduces the size of the stack frame when calling request_module().
Performing the sprintf before the call is not needed.
Signed-off-by: Kees Cook <keescook@chromium.org>
Acked-by: Paul Menzel <paulepanter@users.sourceforge.net>
Signed-off-by: Dave Airlie <airlied@redhat.com>
|
|
drm_helper_probe_single_connector_modes() is responsible for pruning the
previously detected modes on a disconnected connector. We don't really
need to log, again, the full list of modes that used to be valid when
connected.
Signed-off-by: Damien Lespiau <damien.lespiau@intel.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
|
|
As we parse the string given on the command line one char at a time, it
seems that we do want a break at every case.
Signed-off-by: Damien Lespiau <damien.lespiau@intel.com>
Reviewed-by: Rodrigo Vivi <rodrigo.vivi@gmail.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
|
|
git://people.freedesktop.org/~danvet/drm-intel into drm-next
Daniel writes:
A few intel fixes for smaller issues and one revert for an sdv hack which
we've wanted to kill anyway. Plus two drm patches included for your
convenience, both regression fixers for mine own screw-ups.
+ both fixes for stolen mem handling.
* 'for-linux-next' of git://people.freedesktop.org/~danvet/drm-intel:
drm/i915: clear the stolen fb before resuming
Revert "drm/i915: Calculate correct stolen size for GEN7+"
drm/i915: hsw: fix link training for eDP on port-A
Revert "drm/i915: revert eDP bpp clamping code changes"
drm: don't check modeset locks in panic handler
drm/i915: Fix pipe enabled mask for pipe C in WM calculations
drm/mm: fix dump table BUG
drm/i915: Always normalize return timeout for wait_timeout_ioctl
|
|
Similar to
commit 88afe715dd5469bc24ca7a19ac62dd3c241cab48
Author: Chris Wilson <chris@chris-wilson.co.uk>
Date: Sun Dec 16 12:15:41 2012 +0000
drm/i915: Clear the stolen fb before enabling
but on the resume path.
Bugzilla: https://bugzilla.kernel.org/show_bug.cgi?id=57191
Reported-and-tested-by: Nikolay Amiantov <nikoamia@gmail.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: stable@vger.kernel.org (3.9 only)
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
|
|
This reverts commit 03752f5b7b77b95d83479885040950fba1250850.
This revert requires a bit of explanation on how I understand things
work. Internally the architects/designers decide how the stolen encoding
works. We put it in a doc. BIOS writers take these docs and implement
it. Driver writers read the doc too, and read the value left by the BIOS
writers, and then we make magic.
The failing here is that in the docs we had[1] contained two different
definitions for this register for Gen7. (We have both a PCI register,
and an MMIO, and each of these were different). At the time [2] of
03752f5, we asked the architects what the correct value should be; but
that doesn't match the reality (BIOS) unfortunately.
So on all machines I can get my hands on, this revert is the right thing
to do. I've also worked with the product group to confirm that they
agree this revert is what we should do. People using HW made my "people"
who both write their own BIOS, and have access to our docs (Apple?).
Investigations are still ongoing about whether we need to add a list
of machines needing special handling, but this patch should be the
right thing for pretty much everyone.
[1] The docs are still wrong on this one. Now instead of two registers with
two definitions, we have one register with BOTH definitions, progress?
[2] The open source PRMs have the "wrong" definitions in chapter Volume
1 part6, section 1.1.12.
This digging was inspired by Paulo.
Cc: Paulo Zanoni <przanoni@gmail.com>
Signed-off-by: Ben Widawsky <ben@bwidawsk.net>
Acked-by: Jesse Barnes <jbarnes@virtuousgeek.org>
[danvet: Augment the patch saying that it's still a bit unclear
whether there are any machines out there with "wrong" firmware and
whether we need to add a list to handle them specially.]
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
|
|
According to BSpec the link training sequence for eDP on HSW port-A
should be as follows:
1. link training: clock recovery
2. link training: equalization
3. link training: set idle transmission mode
4. display pipe enable
5. link training: disable (set normal mode)
Contrary to this at the moment we don't do step 3. and we do step 5.
before step 4. Fix this by setting idle transmission mode for eDP at
the end of intel_dp_complete_link_train and adding a new
intel_dp_stop_link_training function to disable link training. With
these changes we'll end up with the following functions corresponding
to the above steps:
intel_dp_start_link_train -> step 1.
intel_dp_complete_link_train -> step 2., step 3.
intel_dp_stop_link_train -> step 5.
For port-A we'll call intel_dp_stop_link_train only after enabling the
pipe, for everything else we'll call it right after
intel_dp_complete_link_train to preserve the current behavior.
Tested on HSW/HSW-ULT.
In v2:
- Due to a HW issue we must set idle transmission mode for port-A too
before enabling the pipe. Thanks for Arthur Runyan for explaining
this.
- Update the patch subject to make it clear that it's an eDP fix, DP is
not affected.
v3:
- rename intel_dp_link_train() to intel_dp_set_link_train(), use 'val'
instead 'l' as var name. (Paulo)
Signed-off-by: Imre Deak <imre.deak@intel.com>
Reviewed-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Tested-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
|
|
This reverts commit 57c219633275c7e7413f8bc7be250dc092887458.
It's an ugly hack for a Haswell SDV platform where the vbt doesn't
seem to fully agree with the panel. Since it seems to cause issues on
real eDP platform let's just kill this hack again.
Reported-and-tested-by: Josh Boyer <jwboyer@gmail.com>
References: https://lkml.org/lkml/2013/5/3/467
Cc: Paulo Zanoni <przanoni@gmail.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
|
|
Signed-off-by: Dave Airlie <airlied@redhat.com>
|
|
Merge the fixes for the server driver dirty update paths
* server-fixes:
drm/cirrus: deal with bo reserve fail in dirty update path
drm/ast: deal with bo reserve fail in dirty update path
drm/mgag200: deal with bo reserve fail in dirty update path
|
|
git://gitorious.org/linux-omap-dss2/linux into drm-next
OMAPDSS fixes for 3.10:
* Compilation fix when DSI is disabled in Kconfig
* Basic deferred probe support to fix DT boot
* tag 'omapdss-for-3.10-fixes' of git://gitorious.org/linux-omap-dss2/linux:
OMAPDSS: TFP410: return EPROBE_DEFER if the i2c adapter not found
OMAPDSS: VENC: Add error handling for venc_probe_pdata
OMAPDSS: HDMI: Add error handling for hdmi_probe_pdata
OMAPDSS: RFBI: Add error handling for rfbi_probe_pdata
OMAPDSS: DSI: Add error handling for dsi_probe_pdata
OMAPDSS: SDI: Add error handling for sdi_probe_pdata
OMAPDSS: DPI: Add error handling for dpi_probe_pdata
OMAPDSS: VENC: use platform_driver_register()
OMAPDSS: HDMI: use platform_driver_register()
OMAPDSS: RFBI: use platform_driver_register()
OMAPDSS: DSI: use platform_driver_register()
OMAPDSS: SDI: use platform_driver_register()
OMAPDSS: DPI: use platform_driver_register()
OMAPFB: defer probe if no displays
OMAPFB: use module_platform_driver()
OMAPDSS: Makefile: move omapfb after panels
OMAPDSS: DPI: fix compilation if DSI not compiled in
|
|
into drm-next
Just some fixes that have accumulated over the last couple of
weeks and some new PCI ids.
* 'drm-next-3.10-2' of git://people.freedesktop.org/~agd5f/linux:
drm/radeon: fix handling of v6 power tables
drm/radeon: clarify family checks in pm table parsing
drm/radeon: consolidate UVD clock programming
drm/radeon: fix UPLL_REF_DIV_MASK definition
radeon: add bo tracking debugfs
drm/radeon: add new richland pci ids
drm/radeon: add some new SI PCI ids
drm/radeon: fix scratch reg handling for UVD fence
drm/radeon: allocate SA bo in the requested domain
drm/radeon: fix possible segfault when parsing pm tables
drm/radeon: fix endian bugs in atom_allocate_fb_scratch()
|
|
Since we know that locking is broken in that case and it's more
important to not flood the dmesg with random gunk.
Cc: Dave Airlie <airlied@gmail.com>
Cc: Borislav Petkov <bp@alien8.de>
References: http://lkml.kernel.org/r/20130502000206.GH15623@pd.tnic
Cc: stable@vger.kernel.org
Reported-and-tested-by: Borislav Petkov <bp@suse.de>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
|
|
Signed-off-by: Dave Airlie <airlied@redhat.com>
|
|
The code was mis-handling variable sized arrays.
Reported-by: Sylvain BERTRAND <sylware@legeek.net>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Cc: stable@vger.kernel.org
|
|
We actually care about the chip family rather than the
DCE version although functionally they are the same.
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
|
|
Instead of duplicating the code over and over again, just use a single
function to handle the clock calculations.
Signed-off-by: Christian König <christian.koenig@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
|
|
Stupid copy & paste error over all generations.
Signed-off-by: Christian König <christian.koenig@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
|
|
This is to allow debugging of userspace program not freeing buffer
after, which is basicly a memory leak. This print the list of all
gem object along with their size and placement (VRAM,GTT,CPU) and
with the pid of the task that created them.
agd5f: add warning fix
Signed-off-by: Jerome Glisse <jglisse@redhat.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
|
|
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Cc: stable@vger.kernel.org
|
|
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Cc: stable@vger.kernel.org
|
|
Also init the scratch reg to zero on the UVD ring.
This fixes UVD on AGP based cards.
Signed-off-by: Christian König <christian.koenig@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
|
|
This avoid moving the BO directly after allocating it.
Signed-off-by: Christian König <christian.koenig@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
|
|
If we have a empty power table, bail early and allocate
the default power state.
Should fix:
https://bugs.freedesktop.org/show_bug.cgi?id=63865
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Cc: stable@vger.kernel.org
|
|
Reviwed-by: Michel Dänzer <michel.daenzer@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Cc: stable@vger.kernel.org
|
|
If the I2C adapter needed by the TFP410 device is not available yet,
return EPROBE_DEFER so that the device will get probed again.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
|
|
Add proper error handling for venc_probe_pdata(). This will cause
EPROBE_DEFER to be properly passed upwards, causing the VENC driver to be
probed again later if a resource was missing.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
|
|
Add proper error handling for hdmi_probe_pdata(). This will cause
EPROBE_DEFER to be properly passed upwards, causing the HDMI driver to be
probed again later if a resource was missing.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
|
|
Add proper error handling for rfbi_probe_pdata(). This will cause
EPROBE_DEFER to be properly passed upwards, causing the RFBI driver to be
probed again later if a resource was missing.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
|
|
Add proper error handling for dsi_probe_pdata(). This will cause
EPROBE_DEFER to be properly passed upwards, causing the DSI driver to be
probed again later if a resource was missing.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
|
|
Add proper error handling for sdi_probe_pdata(). This will cause
EPROBE_DEFER to be properly passed upwards, causing the SDI driver to be
probed again later if a resource was missing.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
|
|
Add proper error handling for dpi_probe_pdata(). This will cause
EPROBE_DEFER to be properly passed upwards, causing the DPI driver to be
probed again later if a resource was missing.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
|
|
Use platform_driver_register() instead of platform_driver_probe() so
that we can support EPROBE_DEFER.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
|
|
Use platform_driver_register() instead of platform_driver_probe() so
that we can support EPROBE_DEFER.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
|
|
Use platform_driver_register() instead of platform_driver_probe() so
that we can support EPROBE_DEFER.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
|
|
Use platform_driver_register() instead of platform_driver_probe() so
that we can support EPROBE_DEFER.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
|
|
Use platform_driver_register() instead of platform_driver_probe() so
that we can support EPROBE_DEFER.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
|
|
Use platform_driver_register() instead of platform_driver_probe() so
that we can support EPROBE_DEFER.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
|
