summaryrefslogtreecommitdiff
AgeCommit message (Collapse)Author
2014-09-16scsi: use 'depends' instead of 'select' for SCSI_FC_ATTRSRandy Dunlap
There are other kconfig symbols which use SCSI_FC_ATTRS. In order to maintain sanity and prevent kconfig warnings, change all of these from using 'select' to using 'depends on' so that proper symbol dependencies will be honored and circular depends problems will be avoided. This fixes kconfig warnings and build errors: warning: (LIBFC && SCSI_IBMVFC && SCSI_QLA_FC && SCSI_LPFC && ZFCP && SCSI_BFA_FC && SCSI_CHELSIO_FCOE && FUSION_FC) selects SCSI_FC_ATTRS which has unmet direct dependencies (SCSI && NET) drivers/scsi/scsi_transport_fc.c: In function 'fc_host_post_event': drivers/scsi/scsi_transport_fc.c:543:7: error: 'scsi_nl_sock' undeclared (first use in this function) drivers/scsi/scsi_transport_fc.c: In function 'fc_host_post_vendor_event': drivers/scsi/scsi_transport_fc.c:611:7: error: 'scsi_nl_sock' undeclared (first use in this function) Reported-by: Fengguang Wu <fengguang.wu@intel.com> [0-day test robot] Signed-off-by: Randy Dunlap <rdunlap@infradead.org> Signed-off-by: David S. Miller <davem@davemloft.net>
2014-09-16sfc: fix addr_list_lock spinlock use before initEdward Cree
Reported by Nikolay Aleksandrov. In efx_init_port() we call efx_mac_reconfigure() to work around a Falcon/A1 limitation, and this calls efx_{arch}_filter_sync_rx_mode(), which takes the addr_list_lock; but this lock is uninitialised, because we haven't called register_netdevice() yet. So, in efx_farch_filter_sync_rx_mode(), check efx_dev_registered() before doing anything else. The EF10 equivalent, efx_ef10_filter_sync_rx_mode(), already has the corresponding check. Signed-off-by: Edward Cree <ecree@solarflare.com> Tested-by: Nikolay Aleksandrov <nikolay@redhat.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2014-09-16r8169: adjust __rtl8169_set_featureshayeswang
Remove the "changed" test in __rtl8169_set_features(). Instead, do simple test in rtl8169_set_features(). Set the RxChkSum and RxVlan through __rtl8169_set_features() in rtl_open(). Signed-off-by: Francois Romieu <romieu@fr.zoreil.com> Signed-off-by: Hayes Wang <hayeswang@realtek.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2014-09-16scsi: fix build errors, SCSI_FC_ATTRS needs to depend on SCSI && NETRandy Dunlap
Fix build errors when CONFIG_SCSI_NETLINK is enabled but CONFIG_NET is not enabled: drivers/built-in.o: In function `scsi_nl_rcv_msg': scsi_netlink.c:(.text+0x1850fa): undefined reference to `netlink_ack' scsi_netlink.c:(.text+0x185105): undefined reference to `skb_pull' scsi_netlink.c:(.text+0x18515d): undefined reference to `netlink_capable' drivers/built-in.o: In function `scsi_netlink_init': (.text+0x185244): undefined reference to `init_net' drivers/built-in.o: In function `scsi_netlink_init': (.text+0x185258): undefined reference to `__netlink_kernel_create' drivers/built-in.o: In function `scsi_netlink_exit': (.text+0x185291): undefined reference to `netlink_kernel_release' Signed-off-by: Randy Dunlap <rdunlap@infradead.org> Tested-by: Anish Bhatt <anish@chelsio.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2014-09-15Merge branch 'bnx2-deps'David S. Miller
Anish Bhatt says: ==================== net: Fix randconfig errros in bnx2i/bnx2fc caused by IPV6 Just like CNIC bnx2i/bnx2fc also have their tristate dependent on IPV6, however using the same solution as CNIC can cause recursive dependecies during make. Based on suggestions by Randy Dunlap, SCSI_NETLINK now depends on NET instead of selecting NET. Second patch fixes the actual randconfig error. Entire thread can be followed here : https://lkml.org/lkml/2014/9/9/500 Fixes: c99d667e8527 ("cnic : Cleanup CONFIG_IPV6 & VLAN check") ==================== Signed-off-by: David S. Miller <davem@davemloft.net>
2014-09-15bnx2i/bnx2fc : fix randconfig error in next-20140909Anish Bhatt
Just like CNIC, tristate of these two modules is also dependent on IPV6. These need to be handled separately as they select CNIC, which can override tristate for CNIC from 'm' to 'y', which can cause build failures when ipv6 is compiled as a module even if CNIC's Kconfig will only 'm' or 'n' when ipv6 is compiled as a module. Fixes: c99d667e8527 ("cnic : Cleanup CONFIG_IPV6 & VLAN check") Signed-off-by: Anish Bhatt <anish@chelsio.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2014-09-15scsi_netlink : Make SCSI_NETLINK dependent on NET instead of selecting NETAnish Bhatt
Required for avoiding recursive dependencies in the Kconfig, brought out by fixing randconfig error for bnx2i/bnx2fc in the patch that follows. As suggested by Randy Dunlap Signed-off-by: Anish Bhatt <anish@chelsio.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2014-09-15cxgb4: Don't allocate adapter structure for all PF'sHariprasad Shenai
commit 35b1de557970 ("rdma/cxgb4: Fixes cxgb4 probe failure in VM when PF is exposed through PCI Passthrough") moved the code to check for SR-IOV PF[0..3] much further down in init_one() past the point where we allocate a (struct adapter) for PF[0..3]. As a result, we left four of these on ever module remove. Fix: Allocate adapter structure only for PF4 Signed-off-by: Hariprasad Shenai <hariprasad@chelsio.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2014-09-15bridge: Fix br_should_learn to check vlan_enabledVlad Yasevich
As Toshiaki Makita pointed out, the BRIDGE_INPUT_SKB_CB will not be initialized in br_should_learn() as that function is called only from br_handle_local_finish(). That is an input handler for link-local ethernet traffic so it perfectly correct to check br->vlan_enabled here. Reported-by: Toshiaki Makita<toshiaki.makita1@gmail.com> Fixes: 20adfa1 bridge: Check if vlan filtering is enabled only once. Signed-off-by: Vladislav Yasevich <vyasevic@redhat.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2014-09-15net: fix creation adjacent device symlinksAlexander Y. Fomichev
__netdev_adjacent_dev_insert may add adjust device of different net namespace, without proper check it leads to emergence of broken sysfs links from/to devices in another namespace. Fix: rewrite netdev_adjacent_is_neigh_list macro as a function, move net_eq check into netdev_adjacent_is_neigh_list. (thanks David) related to: 4c75431ac3520631f1d9e74aa88407e6374dbbc4 Signed-off-by: Alexander Fomichev <git.user@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2014-09-15net/phy: micrel: Disable asymmetric pause for KSZ9031Mike Looijmans
The KSZ9031 appears to suffer from the same hardware bug as described for the KSZ9021 in commit 32fcafbcd1c9f6c7013016a22a5369b4acb93577 ("net/phy: micrel: Disable asymmetric pause for KSZ9021") you have to unplug the cable and plug it back to get it to work. Remove the SUPPORTED_Asym_Pause flag for the KSZ9031 to fix this. Signed-off-by: Mike Looijmans <mike.looijmans@topic.nl> Signed-off-by: David S. Miller <davem@davemloft.net>
2014-09-13Merge branch 'bridge_vlan_filtering'David S. Miller
Vladislav Yasevich says: ==================== bridge: Two small fixes to vlan filtering code. This series corrects 2 small issues that I've ran across recently while doing more work with vlan filtering changes. ==================== Signed-off-by: David S. Miller <davem@davemloft.net>
2014-09-13bridge: Allow clearing of pvid and untagged bitmapVlad Yasevich
Currently, it is possible to modify the vlan filter configuration to add pvid or untagged support. For example: bridge vlan add vid 10 dev eth0 bridge vlan add vid 10 dev eth0 untagged pvid The second statement will modify vlan 10 to include untagged and pvid configuration. However, it is currently impossible to go backwards bridge vlan add vid 10 dev eth0 untagged pvid bridge vlan add vid 10 dev eth0 Here nothing happens. This patch correct this so that any modifiers not supplied are removed from the configuration. Signed-off-by: Vlad Yasevich <vyasevic@redhat.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2014-09-13bridge: Check if vlan filtering is enabled only once.Vlad Yasevich
The bridge code checks if vlan filtering is enabled on both ingress and egress. When the state flip happens, it is possible for the bridge to currently be forwarding packets and forwarding behavior becomes non-deterministic. Bridge may drop packets on some interfaces, but not others. This patch solves this by caching the filtered state of the packet into skb_cb on ingress. The skb_cb is guaranteed to not be over-written between the time packet entres bridge forwarding path and the time it leaves it. On egress, we can then check the cached state to see if we need to apply filtering information. Signed-off-by: Vladislav Yasevich <vyasevic@redhat.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2014-09-13bonding: fix div by zero while enslaving and transmittingNikolay Aleksandrov
The problem is that the slave is first linked and slave_cnt is incremented afterwards leading to a div by zero in the modes that use it as a modulus. What happens is that in bond_start_xmit() bond_has_slaves() is used to evaluate further transmission and it becomes true after the slave is linked in, but when slave_cnt is used in the xmit path it is still 0, so fetch it once and transmit based on that. Since it is used only in round-robin and XOR modes, the fix is only for them. Thanks to Eric Dumazet for pointing out the fault in my first try to fix this. Call trace (took it out of net-next kernel, but it's the same with net): [46934.330038] divide error: 0000 [#1] SMP [46934.330041] Modules linked in: bonding(O) 9p fscache snd_hda_codec_generic crct10dif_pclmul [46934.330041] bond0: Enslaving eth1 as an active interface with an up link [46934.330051] ppdev joydev crc32_pclmul crc32c_intel 9pnet_virtio ghash_clmulni_intel snd_hda_intel 9pnet snd_hda_controller parport_pc serio_raw pcspkr snd_hda_codec parport virtio_balloon virtio_console snd_hwdep snd_pcm pvpanic i2c_piix4 snd_timer i2ccore snd soundcore virtio_blk virtio_net virtio_pci virtio_ring virtio ata_generic pata_acpi floppy [last unloaded: bonding] [46934.330053] CPU: 1 PID: 3382 Comm: ping Tainted: G O 3.17.0-rc4+ #27 [46934.330053] Hardware name: Bochs Bochs, BIOS Bochs 01/01/2011 [46934.330054] task: ffff88005aebf2c0 ti: ffff88005b728000 task.ti: ffff88005b728000 [46934.330059] RIP: 0010:[<ffffffffa0198c33>] [<ffffffffa0198c33>] bond_start_xmit+0x1c3/0x450 [bonding] [46934.330060] RSP: 0018:ffff88005b72b7f8 EFLAGS: 00010246 [46934.330060] RAX: 0000000000000679 RBX: ffff88004b077000 RCX: 000000000000002a [46934.330061] RDX: 0000000000000000 RSI: ffff88004b3f0500 RDI: ffff88004b077940 [46934.330061] RBP: ffff88005b72b830 R08: 00000000000000c0 R09: ffff88004a83e000 [46934.330062] R10: 000000000000ffff R11: ffff88004b1f12c0 R12: ffff88004b3f0500 [46934.330062] R13: ffff88004b3f0500 R14: 000000000000002a R15: ffff88004b077940 [46934.330063] FS: 00007fbd91a4c740(0000) GS:ffff88005f080000(0000) knlGS:0000000000000000 [46934.330064] CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033 [46934.330064] CR2: 00007f803a8bb000 CR3: 000000004b2c9000 CR4: 00000000000406e0 [46934.330069] Stack: [46934.330071] ffffffff811e6169 00000000e772fa05 ffff88004b077000 ffff88004b3f0500 [46934.330072] ffffffff81d17d18 000000000000002a 0000000000000000 ffff88005b72b8a0 [46934.330073] ffffffff81620108 ffffffff8161fe0e ffff88005b72b8c4 ffff88005b302000 [46934.330073] Call Trace: [46934.330077] [<ffffffff811e6169>] ? __kmalloc_node_track_caller+0x119/0x300 [46934.330084] [<ffffffff81620108>] dev_hard_start_xmit+0x188/0x410 [46934.330086] [<ffffffff8161fe0e>] ? harmonize_features+0x2e/0x90 [46934.330088] [<ffffffff81620b06>] __dev_queue_xmit+0x456/0x590 [46934.330089] [<ffffffff81620c50>] dev_queue_xmit+0x10/0x20 [46934.330090] [<ffffffff8168f022>] arp_xmit+0x22/0x60 [46934.330091] [<ffffffff8168f090>] arp_send.part.16+0x30/0x40 [46934.330092] [<ffffffff8168f1e5>] arp_solicit+0x115/0x2b0 [46934.330094] [<ffffffff8160b5d7>] ? copy_skb_header+0x17/0xa0 [46934.330096] [<ffffffff8162875a>] neigh_probe+0x4a/0x70 [46934.330097] [<ffffffff8162979c>] __neigh_event_send+0xac/0x230 [46934.330098] [<ffffffff8162a00b>] neigh_resolve_output+0x13b/0x220 [46934.330100] [<ffffffff8165f120>] ? ip_forward_options+0x1c0/0x1c0 [46934.330101] [<ffffffff81660478>] ip_finish_output+0x1f8/0x860 [46934.330102] [<ffffffff81661f08>] ip_output+0x58/0x90 [46934.330103] [<ffffffff81661602>] ? __ip_local_out+0xa2/0xb0 [46934.330104] [<ffffffff81661640>] ip_local_out_sk+0x30/0x40 [46934.330105] [<ffffffff81662a66>] ip_send_skb+0x16/0x50 [46934.330106] [<ffffffff81662ad3>] ip_push_pending_frames+0x33/0x40 [46934.330107] [<ffffffff8168854c>] raw_sendmsg+0x88c/0xa30 [46934.330110] [<ffffffff81612b31>] ? skb_recv_datagram+0x41/0x60 [46934.330111] [<ffffffff816875a9>] ? raw_recvmsg+0xa9/0x1f0 [46934.330113] [<ffffffff816978d4>] inet_sendmsg+0x74/0xc0 [46934.330114] [<ffffffff81697a9b>] ? inet_recvmsg+0x8b/0xb0 [46934.330115] bond0: Adding slave eth2 [46934.330116] [<ffffffff8160357c>] sock_sendmsg+0x9c/0xe0 [46934.330118] [<ffffffff81603248>] ? move_addr_to_kernel.part.20+0x28/0x80 [46934.330121] [<ffffffff811b4477>] ? might_fault+0x47/0x50 [46934.330122] [<ffffffff816039b9>] ___sys_sendmsg+0x3a9/0x3c0 [46934.330125] [<ffffffff8144a14a>] ? n_tty_write+0x3aa/0x530 [46934.330127] [<ffffffff810d1ae4>] ? __wake_up+0x44/0x50 [46934.330129] [<ffffffff81242b38>] ? fsnotify+0x238/0x310 [46934.330130] [<ffffffff816048a1>] __sys_sendmsg+0x51/0x90 [46934.330131] [<ffffffff816048f2>] SyS_sendmsg+0x12/0x20 [46934.330134] [<ffffffff81738b29>] system_call_fastpath+0x16/0x1b [46934.330144] Code: 48 8b 10 4c 89 ee 4c 89 ff e8 aa bc ff ff 31 c0 e9 1a ff ff ff 0f 1f 00 4c 89 ee 4c 89 ff e8 65 fb ff ff 31 d2 4c 89 ee 4c 89 ff <f7> b3 64 09 00 00 e8 02 bd ff ff 31 c0 e9 f2 fe ff ff 0f 1f 00 [46934.330146] RIP [<ffffffffa0198c33>] bond_start_xmit+0x1c3/0x450 [bonding] [46934.330146] RSP <ffff88005b72b7f8> CC: Eric Dumazet <eric.dumazet@gmail.com> CC: Andy Gospodarek <andy@greyhouse.net> CC: Jay Vosburgh <j.vosburgh@gmail.com> CC: Veaceslav Falico <vfalico@gmail.com> Fixes: 278b208375 ("bonding: initial RCU conversion") Signed-off-by: Nikolay Aleksandrov <nikolay@redhat.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2014-09-13Merge branch 'r8169-net'David S. Miller
Hayes Wang says: ==================== r8169: fix rx vlan There are two issues for hw rx vlan. The patches are used to fix them. ==================== Signed-off-by: David S. Miller <davem@davemloft.net>
2014-09-13r8169: fix setting rx vlanhayeswang
The setting should depend on the new features not the current one. Signed-off-by: Hayes Wang <hayeswang@realtek.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2014-09-13r8169: fix the default setting of rx vlanhayeswang
If the parameter "features" of __rtl8169_set_features() is equal to dev->features, the variable "changed" is alwayes 0, and nothing would be changed. Signed-off-by: Hayes Wang <hayeswang@realtek.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2014-09-13drivers: net: cpsw: dual_emac: in suspend/resume bring down/up all the netdevMugunthan V N
During suspend and resume in Dual EMAC, second port is not working as in suspend/resume only the first slave netdev is closed and opened. So bring down and up all the interfaces that are up during suspend/resume. Signed-off-by: Mugunthan V N <mugunthanvnm@ti.com> Tested-by: Nishanth Menon <nm@ti.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2014-09-12drivers: net: b44: Fix typo in returning multicast statsMark Einon
nstat->multicast refers to received packets, not transmitted as is returned here. Change it so that received packet stats are given. Signed-off-by: Mark Einon <mark.einon@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2014-09-12Merge tag 'master-2014-09-11' of ↵David S. Miller
git://git.kernel.org/pub/scm/linux/kernel/git/linville/wireless John W. Linville says: ==================== pull request: wireless 2014-09-11 Please pull this batch of fixes intended for the 3.17 stream: For the mac80211 bits, Johannes says: "Two more fixes for mac80211 - one of them addresses a long-standing issue that we only found when using vendor events more frequently; the other addresses some bad information being reported in userspace that people were starting to actually look at." For the iwlwifi bits, Emmanuel says: "I re-enable scheduled scan on firmware that contain the fix for the bug that Linus reported. A few trivial fixes: endianity issues, the same DTIM period fix that I did in mac80211. Eyal fixes a few issues we identified with EAPOL, we now send them just as if they were management frames, this solves interrop issues. Johannes has another set of trivial fixes, while Luca fixes the way we configure the filters in the firmware. Last but not least, a new device is added by Oren." Emmanuel was traveling, resulting in his pull to be a bit larger than I would have liked to see at this point. FWIW, I have asked Emmanuel to be much more strict for any more pull requests in this cycle. In addition to the above, Sujith Manoharan reverts an earlier ath9k patch. The earlier change was found to allow for the device to sleep too long and miss beacons. ==================== Signed-off-by: David S. Miller <davem@davemloft.net>
2014-09-12Merge tag 'linux-can-fixes-for-3.17-20140911' of ↵David S. Miller
git://gitorious.org/linux-can/linux-can Marc Kleine-Budde says: ==================== pull-request: can 2014-09-11 this is a pull request for the current release cycle of a single patch. The patch by David Jander fixes a scheduling while atomic problem in the flexcan driver, that was introduced by me in v3.14-rc6. ==================== Signed-off-by: David S. Miller <davem@davemloft.net>
2014-09-12ipv6: clean up anycast when an interface is destroyedSabrina Dubroca
If we try to rmmod the driver for an interface while sockets with setsockopt(JOIN_ANYCAST) are alive, some refcounts aren't cleaned up and we get stuck on: unregister_netdevice: waiting for ens3 to become free. Usage count = 1 If we LEAVE_ANYCAST/close everything before rmmod'ing, there is no problem. We need to perform a cleanup similar to the one for multicast in addrconf_ifdown(how == 1). Signed-off-by: Sabrina Dubroca <sd@queasysnail.net> Acked-by: Hannes Frederic Sowa <hannes@stressinduktion.org> Signed-off-by: David S. Miller <davem@davemloft.net>
2014-09-12Merge branch 'arc_emac'David S. Miller
Beniamino Galvani says: ==================== net: arc_emac: fix tx issues the patches below solve some issues found in the tx ring reclaim strategy currently implemented in the arc_emac driver. Without these patches a simple outgoing UDP flow blocks almost immediately with the socket send buffer full, until some new rx packets trigger a clean of the tx ring. Everything seems to work fine on a Radxa Rock with this fix applied. ==================== Signed-off-by: David S. Miller <davem@davemloft.net>
2014-09-12net: arc_emac: prevent reuse of unreclaimed tx descriptorsBeniamino Galvani
This patch changes the logic in tx path to ensure that tx descriptors are reused for transmission only after they have been reclaimed by arc_emac_tx_clean(). Signed-off-by: Beniamino Galvani <b.galvani@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2014-09-12net: arc_emac: enable tx interruptsBeniamino Galvani
In the current implementation the cleaning of tx ring is done by the NAPI poll handler, which is scheduled after rx interrupts. Thus, in absence of received packets the reclaim of used tx buffers is never executed, blocking further transmission. This can be easily reproduced starting the transmission of a UDP flow with iperf, which blocks almost immediately because skbs are not returned to the stack and the socket send buffer becomes full. The patch enables tx interrupts so that the tx reclaim is scheduled after completed transmissions. Signed-off-by: Beniamino Galvani <b.galvani@gmail.com> Reviewed-by: Florian Fainelli <f.fainelli@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2014-09-11Revert "ath9k: Calculate sleep duration"Sujith Manoharan
This reverts commit 09ebb810927a110e4c354beb20308830d108a54b. ath9k_hw_set_sta_beacon_timers() configures AR_TIM_PERIOD with the beacon interval. Before this commit, the sleepduration was never greater than the beacon interval. But now, the behavior has changed. For example, with an AP that uses a beacon interval of 100: ath: phy9: next beacon 61128704 ath: phy9: beacon period 204800 ath: phy9: DTIM period 204800 If the sleepduration is calculated based on the listen time, then the bmiss threshold should also be changed since the HW would be in sleep state for a longer time, but that is not done currently. To avoid configuring a higher beacon interval based on the sleepduration, revert to the original behavior. Power consumption is not a problem since PS is disabled in ath9k anyway. Cc: stable@vger.kernel.org Cc: Rajkumar Manoharan <rmanohar@qti.qualcomm.com> Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2014-09-11can: flexcan: avoid calling usleep_range from interrupt contextDavid Jander
Apparently can_restart() runs from a (timer-) interrupt and can call flexcan_chip_[en|dis]able(), so avoid using usleep_range() Signed-off-by: David Jander <david@protonic.nl> Cc: linux-stable <stable@vger.kernel.org> Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
2014-09-10Documentation: filter: Add MIPS to architectures with BPF JITMarkos Chandras
MIPS supports BPF JIT since v3.16-rc1 Cc: Randy Dunlap <rdunlap@infradead.org> Cc: "David S. Miller" <davem@davemloft.net> Cc: Daniel Borkmann <dborkman@redhat.com> Cc: Alexei Starovoitov <ast@plumgrid.com> Cc: linux-doc@vger.kernel.org Cc: linux-kernel@vger.kernel.org Acked-by: Daniel Borkmann <dborkman@redhat.com> Signed-off-by: Markos Chandras <markos.chandras@imgtec.com> Acked-by: Alexei Starovoitov <ast@plumgrid.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2014-09-10mlx4: Fix wrong endianess access with QP context flagsOr Gerlitz
We wrongly tested QP context bits without BE conversion as was spotted by sparse... drivers/infiniband/hw/mlx4/qp.c:1685:38: sparse: restricted __be32 degrades to integer Fix that! Fixes: d2fce8a ('mlx4: Set user-space raw Ethernet QPs to properly handle VXLAN traffic') Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2014-09-10Merge branch 'mlx4'David S. Miller
Or Gerlitz says: ==================== mlx4 SRIOV fixes This series contains few SRIOV related fixes from Matan, please apply to net. ==================== Signed-off-by: David S. Miller <davem@davemloft.net>
2014-09-10net/mlx4: Set vlan stripping policy by the right commandMatan Barak
Changing the vlan stripping policy of the QP isn't supported by older firmware versions for the INIT2RTR command. Nevertheless, we've used it. Fix that by doing this policy change using INIT2RTR only if the firmware supports it, otherwise, we call UPDATE_QP command to do the task. Fixes: 7677fc9 ('net/mlx4: Strengthen VLAN tags/priorities enforcement in VST mode') Signed-off-by: Matan Barak <matanb@mellanox.com> Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2014-09-10net/mlx4: Avoid dealing with MAC index in UPDATE_QP wrapper if not neededMatan Barak
The current wrapper implementation of the UPDATE_QP command tries to get the MAC index, even if MAC wasn't set by the VF. Fix it up to only handle the MAC field if it's valid. Fixes: ce8d9e0 ('net/mlx4_core: Add UPDATE_QP SRIOV wrapper support') Signed-off-by: Matan Barak <matanb@mellanox.com> Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2014-09-10net/mlx4: Use the correct VSD mask in UPDATE_QPMatan Barak
When doing VGT->VST->VGT state changes, we used an incorrect mask for the vlan-stripping-disable (VSD) flag, hence the vlan related policy for user-space Raw Ethernet QPs open by VFs wasn't really applied. Fix that, by using the correct mask. Fixes: f0f829b ('net/mlx4_core: Add immediate activate for VGT->VST->VGT') Signed-off-by: Matan Barak <matanb@mellanox.com> Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2014-09-10net/mlx4: Correctly configure single ported VFs from the hostMatan Barak
Single port VFs are seen PCI wise on both ports of the PF (we don't have single port PFs with ConnectX). With this in mind, it's possible for virtualization tools to try and configure a single ported VF through the "wrong" PF port. To handle that, we use the PF driver mapping of single port VFs to NIC ports and adjust the port value before calling into the low level code that does the actual VF configuration Fixes: 449fc48 ('net/mlx4: Adapt code for N-Port VF') Signed-off-by: Matan Barak <matanb@mellanox.com> Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2014-09-10drivers: net: cpsw: dual_emac: fix reducing of rx descriptor during ifdownMugunthan V N
In Dual EMAC, when both interface are up and while doing ifdown with heavy traffic then skbs already processed by DMA from that slave emac has to be requeued as still the other interface is up and running. Signed-off-by: Mugunthan V N <mugunthanvnm@ti.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2014-09-09RxRPC: Fix missing __user annotationDavid Howells
Fix a missing __user annotation in a cast of a user space pointer (found by checker). Signed-off-by: David Howells <dhowells@redhat.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2014-09-09net:bonding: Add missing space in bonding driver parameter descriptionMasanari Iida
This patch adds missing space between "interface" and "by" in bonding module parameter description. Signed-off-by: Masanari Iida <standby24x7@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2014-09-09net:socket: set msg_namelen to 0 if msg_name is passed as NULL in msghdr ↵Ani Sinha
struct from userland. Linux manpage for recvmsg and sendmsg calls does not explicitly mention setting msg_namelen to 0 when msg_name passed set as NULL. When developers don't set msg_namelen member in msghdr, it might contain garbage value which will fail the validation check and sendmsg and recvmsg calls from kernel will return EINVAL. This will break old binaries and any code for which there is no access to source code. To fix this, we set msg_namelen to 0 when msg_name is passed as NULL from userland. Signed-off-by: Ani Sinha <ani@arista.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2014-09-09Merge branch 'for-john' of ↵John W. Linville
git://git.kernel.org/pub/scm/linux/kernel/git/iwlwifi/iwlwifi-fixes
2014-09-09Merge tag 'mac80211-for-john-2014-09-08' of ↵John W. Linville
git://git.kernel.org/pub/scm/linux/kernel/git/jberg/mac80211 Johannes Berg <johannes@sipsolutions.net> says: "Two more fixes for mac80211 - one of them addresses a long-standing issue that we only found when using vendor events more frequently; the other addresses some bad information being reported in userspace that people were starting to actually look at." Signed-off-by: John W. Linville <linville@tuxdriver.com>
2014-09-08Merge branch 'oom_fixes'David S. Miller
Florian Fainelli says: ==================== net: systemport and bcmgenet OOM fixes These two patches fix similar Out of Memory code paths in the SYSTEMPORT and GENET drivers. Under high memory pressure, we could produce an OOPS by passing a NULL pointer to dma_unmap_single(). ==================== Signed-off-by: David S. Miller <davem@davemloft.net>
2014-09-08net: bcmgenet: check harder for out of memory conditionsFlorian Fainelli
There is a potential case where we might be failing to refill a control block, leaving it with both a NULL skb pointer *and* a NULL dma_unmap_addr. The way we process incoming packets, by first calling dma_unmap_single(), and then only checking for a potential NULL skb can lead to situations where do pass a NULL dma_unmap_addr() to dma_unmap_single(), resulting in an oops. Fix this my moving the NULL skb check earlier, since no backing skb also means no corresponding DMA mapping for this packet. Signed-off-by: Florian Fainelli <f.fainelli@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2014-09-08net: systemport: check harder for out of memory conditionsFlorian Fainelli
There is a potential case where we might be failing to refill a control block, leaving it with both a NULL skb pointer *and* a NULL dma_unmap_addr. The way we process incoming packets, by first calling dma_unmap_single(), and then only checking for a potential NULL skb can lead to situations where do pass a NULL dma_unmap_addr() to dma_unmap_single(), resulting in an oops. Fix this my moving the NULL skb check earlier, since no backing skb also means no corresponding DMA mapping for this packet. Signed-off-by: Florian Fainelli <f.fainelli@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2014-09-08net/mlx4_en: do not ignore autoneg in mlx4_en_set_pauseparam()Ivan Vecera
The driver does not support pause autonegotiation so it should return -EINVAL when the function is called with non-zero autoneg. Cc: Amir Vadai <amirv@mellanox.com> Signed-off-by: Ivan Vecera <ivecera@redhat.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2014-09-08drivers: net: ethernet: octeon_mgmt: fix a compiler warningAaro Koskinen
Fix the following compiler warning: drivers/net/ethernet/octeon/octeon_mgmt.c: In function 'octeon_mgmt_clean_tx_buffers': drivers/net/ethernet/octeon/octeon_mgmt.c:295:4: warning: ISO C90 forbids mixed declarations and code [-Wdeclaration-after-statement] u64 ns = cvmx_read_csr(CVMX_MIXX_TSTAMP(p->port)); ^ Signed-off-by: Aaro Koskinen <aaro.koskinen@nsn.com> Acked-by: David Daney <david.daney@cavium.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2014-09-08net: fix skb_page_frag_refill() kerneldocEric Dumazet
In commit d9b2938aabf7 ("net: attempt a single high order allocation) I forgot to update kerneldoc, as @prio parameter was renamed to @gfp Signed-off-by: Eric Dumazet <edumazet@google.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2014-09-08sunvnet - add missing rmb() for sunvnet driverDavid L Stevens
The sunvnet driver does not have an rmb() in the ring consumer corresponding to the wmb() in the producer. According to Documentation/memory-barriers.txt: "When dealing with CPU-CPU interactions, certain types of memory barrier should always be paired. A lack of appropriate pairing is almost certainly an error." In cases where an rmb() is not a no-op and a consumer is removing data from the ring while a producer is adding new entries, a load reorder would allow CPU1 CPU2 ---- ---- LOAD desc.size [e.g] STORE desc.size <wmb> set desc.hdr.state = VIO_DESC_READY LOAD desc.hdr.state [because VIO_DESC_READY, use old desc.size, already loaded out of order] [CPU2 has reordered apparently unrelated LOADs] To ensure other desc fields are not loaded before checking VIO_DESC_READY, we need an rmb() between the check and desc data accesses. I've also moved the viodbg() call to after the rmb() so that it, too, has current descriptor data even with reordering, which has the side effect that it won't print anything for descriptors that are not VIO_DESC_READY as before. That's a) probably a good thing, since the fields are not necessarily set and, b) better than adding another rmb() just for viodbg(). This would not be possible if strict-ordering is enforced, but then the memory barriers should be no-ops in that case. Signed-off-by: David L Stevens <david.stevens@oracle.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2014-09-08iwlwifi: mvm: fix an overflow in iwl_mvm_get_signal_strengthEyal Shapira
The idea here is to translate a value of 0 received from the firmware to the lowest rssi figure. As rx_status->chain_signal is a signed byte the lowest possible value is -128 and not -256. -256 was causing 0 to get stored in the signed byte. Signed-off-by: Eyal Shapira <eyalx.shapira@intel.com> Reviewed-by: Johannes Berg <johannes.berg@intel.com> Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
2014-09-08iwlwifi: add PCI IDs and add then new 3165 seriesOren Givon
This change does the following: 1) Add a new 7265 series PCI ID 2) Add two new 3160 series PCI IDs 3) Add the new 3165 series PCI IDs and configurations Signed-off-by: Oren Givon <oren.givon@intel.com> Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
generated by cgit v1.2.3 (git 2.0.4) at 2025-01-09 09:10:59 +0000