| Age | Commit message (Collapse) | Author |
|---|
|
commit f511ab09dfb0fe7b2335eccac51ff9f001a32e4a upstream.
They are used to decide if the controller can do DMA on a buffer
of a specific length and thus are needed before any transfer is attempted.
This fixes a memory leak where the SPI core uses the drivers can_dma()
callback to determine if a buffer needs to be mapped. As the watermark
levels aren't correct at that point the driver falsely claims to be able to
DMA the buffer when it fact it isn't.
After the transfer has been done the core uses the same callback to
determine if it needs to unmap the buffers. As the driver now correctly
claims to not being able to DMA the buffer the core doesn't attempt to
unmap the buffer which leaves the SGT leaking.
Fixes: f62caccd12c17e4 (spi: spi-imx: add DMA support)
Signed-off-by: Lucas Stach <l.stach@pengutronix.de>
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 9e71c589e44ddf2b86f361c81e360c6b0d0354b1 upstream.
The reset control for the sunxi mmc controller is optional. Some
newer platforms (sun6i, sun8i, sun9i) have it, while older ones
(sun4i, sun5i, sun7i) don't.
Use the properly stubbed _optional version so the driver does not
fail to compile when RESET_CONTROLLER=n.
This patch also adds a check for deferred probing on the reset
control.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Acked-by: David Lanzendörfer <david.lanzendoerfer@o2s.ch>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 13a6a2ed1f5e77ae47c2b1a8e3bf22b2fa2d56ba upstream.
If CONFIG_DEBUG_SLAB=y:
sh_mobile_sdhi ee100000.sd: Got CD GPIO
sh_mobile_sdhi ee100000.sd: Got WP GPIO
platform ee100000.sd: Driver sh_mobile_sdhi requests probe deferral
...
Slab corruption (Not tainted): kmalloc-1024 start=ed8b3c00, len=1024
2d0: 00 00 00 00 6b 6b 6b 6b 6b 6b 6b 6b 6b 6b 6b 6b ....kkkkkkkkkkkk
Prev obj: start=ed8b3800, len=1024
000: 6b 6b 6b 6b 6b 6b 6b 6b 6b 6b 6b 6b 6b 6b 6b 6b kkkkkkkkkkkkkkkk
010: 6b 6b 6b 6b 6b 6b 6b 6b 6b 6b 6b 6b 6b 6b 6b 6b kkkkkkkkkkkkkkkk
Struct tmio_mmc_host is embedded inside struct mmc_host, and thus is
freed by the call to mmc_free_host(). Hence it must not be written to
afterwards, as that will corrupt freed (and perhaps already reused)
memory.
Fixes: 94b110aff8679b14 ("mmc: tmio: add tmio_mmc_host_alloc/free()")
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 323ece54e0761198946ecd0c2091f1d2bfdfcb64 upstream.
Values directly from descriptors given in debug statements
must be converted to native endianness.
Signed-off-by: Oliver Neukum <oneukum@suse.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 8a7d95f95c95f396decbd4cda6d4903fc4664946 upstream.
On architectures that depend on DT for obtaining cache hierarcy, we need
to validate the device node for all the cache indices, failing to do so
might result in wrong information being exposed to the userspace.
This is quite possible on initial/incomplete versions of the device
trees. In such cases, it's better to bail out if all the required device
nodes are not present.
This patch adds checks for the validation of device node for all the
caches and doesn't initialise the cacheinfo if there's any error.
Reported-by: Mark Rutland <mark.rutland@arm.com>
Acked-by: Mark Rutland <mark.rutland@arm.com>
Signed-off-by: Sudeep Holla <sudeep.holla@arm.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 16b8528d20607925899b1df93bfd8fbab98d267c upstream.
We only want to steer the I/O completion towards a queue, but don't
actually access any per-CPU data, so the raw_ version is fine to use
and avoids the warnings when using smp_processor_id().
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reported-by: Andy Lutomirski <luto@kernel.org>
Tested-by: Andy Lutomirski <luto@kernel.org>
Acked-by: Sumit Saxena <sumit.saxena@avagotech.com>
Signed-off-by: James Bottomley <JBottomley@Odin.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 47d68979cc968535cb87f3e5f2e6a3533ea48fbd upstream.
Since commit 20d0189b1012a37d2533a87fb451f7852f2418d1
in v3.14-rc1 RAID0 has performed incorrect calculations
when the chunksize is not a power of 2.
This happens because "sector_div()" modifies its first argument, but
this wasn't taken into account in the patch.
So restore that first arg before re-using the variable.
Reported-by: Joe Landman <joe.landman@gmail.com>
Reported-by: Dave Chinner <david@fromorbit.com>
Fixes: 20d0189b1012a37d2533a87fb451f7852f2418d1
Signed-off-by: NeilBrown <neilb@suse.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit a6388e68321a1e0a0f408379c2a36396807745b3 upstream.
Information for packet type is in ieee80211_tx_info
band IEEE80211_BAND_5GHZ for PK_TYPE_11A.
IEEE80211_TX_RC_USE_CTS_PROTECT via tx_rate flags selects PK_TYPE_11GB
This ensures that the packet is always the right type.
Signed-off-by: Malcolm Priestley <tvboxspy@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 8e43c9c75faf2902955bd2ecd7a50a8cc41cb00a upstream.
The android_fence_release() function checks for active sync points
by calling list_empty() on the list head embedded on the sync
point. However, it is only valid to use list_empty() on nodes that
have been initialized with INIT_LIST_HEAD() or list_del_init().
Because the list entry has likely been removed from the active list
by sync_timeline_signal(), there is a good chance that this
WARN_ON_ONCE() will be hit due to dangling pointers pointing at
freed memory (even though the sync drivers did nothing wrong)
and memory corruption will ensue as the list entry is removed for
a second time, corrupting the active list.
This problem can be reproduced quite easily with CONFIG_DEBUG_LIST=y
and fences with more than one sync point.
Signed-off-by: Alistair Strachan <alistair.strachan@imgtec.com>
Cc: Maarten Lankhorst <maarten.lankhorst@canonical.com>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: Colin Cross <ccross@google.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 2c20d92dad5db6440cfa88d811b69fd605240ce4 upstream.
the lcd type as defined in the Kconfig is not matching in the code.
as a result the rs, rw and en pins were getting interchanged.
Kconfig defines the value of PANEL_LCD to be 1 if we select custom
configuration but in the code LCD_TYPE_CUSTOM is defined as 5.
my hardware is LCD_TYPE_CUSTOM, but the pins were assigned to it
as pins of LCD_TYPE_OLD, and it was not working.
Now values are corrected with referenece to the values defined in
Kconfig and it is working.
checked on JHD204A lcd with LCD_TYPE_CUSTOM configuration.
Signed-off-by: Sudip Mukherjee <sudip@vectorindia.org>
Acked-by: Willy Tarreau <w@1wt.eu>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit a843d00d038b11267279e3b5388222320f9ddc1d upstream.
We found that TLB mismatch not only happens after kernel resume, but
also happens during snapshot restore. So move it to the beginning of
swsusp_arch_suspend().
Signed-off-by: Huacai Chen <chenhc@lemote.com>
Cc: Steven J. Hill <Steven.Hill@imgtec.com>
Cc: linux-mips@linux-mips.org
Cc: Fuxin Zhang <zhangfx@lemote.com>
Cc: Zhangjin Wu <wuzhangjin@gmail.com>
Patchwork: https://patchwork.linux-mips.org/patch/9621/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 0add9c2f1cff9f3f1f2eb7e9babefa872a9d14b9 upstream.
HPET irq is routed to i8259 and then to MIPS CPU irq (cascade). After
commit a3e6c1eff5 (MIPS: IRQ: Fix disable_irq on CPU IRQs), if without
IRQF_NO_SUSPEND in cascade_irqaction, HPET interrupts will lost during
suspend. The result is machine cannot be waken up.
Signed-off-by: Huacai Chen <chenhc@lemote.com>
Cc: Steven J. Hill <Steven.Hill@imgtec.com>
Cc: linux-mips@linux-mips.org
Cc: Fuxin Zhang <zhangfx@lemote.com>
Cc: Zhangjin Wu <wuzhangjin@gmail.com>
Patchwork: https://patchwork.linux-mips.org/patch/9528/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 6eae35485b26f9e51ab896eb8a936bed9908fdf6 upstream.
When emulating a regular lh/lw/lhu/sh/sw we need to use the appropriate
instruction if we are in EVA mode. This is necessary for userspace
applications which trigger alignment exceptions. In such case, the
userspace load/store instruction needs to be emulated with the correct
eva/non-eva instruction by the kernel emulator.
Signed-off-by: Markos Chandras <markos.chandras@imgtec.com>
Fixes: c1771216ab48 ("MIPS: kernel: unaligned: Handle unaligned accesses for EVA")
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/9503/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 3563c32d6532ece53c9dd8905a8e41983ef9952f upstream.
It's best to surround such complex macros with do {} while statements
so they can appear as independent logical blocks when used within other
control blocks.
Signed-off-by: Markos Chandras <markos.chandras@imgtec.com>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/9502/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit eeb538950367e3966cbf0237ab1a1dc30e059818 upstream.
Commit c1771216ab48 ("MIPS: kernel: unaligned: Handle unaligned
accesses for EVA") allowed unaligned accesses to be emulated for
EVA. However, when emulating regular load/store unaligned accesses,
we need to use the appropriate "address space" instructions for that.
Previously, an unaligned load/store instruction in kernel space would
have used the corresponding EVA instructions to emulate it which led to
segmentation faults because of the address translation that happens
with EVA instructions. This is now fixed by using the EVA instruction
only when emulating EVA unaligned accesses.
Signed-off-by: Markos Chandras <markos.chandras@imgtec.com>
Fixes: c1771216ab48 ("MIPS: kernel: unaligned: Handle unaligned accesses for EVA")
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/9501/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 60cd7e08e453bc6828ac4b539f949e4acd80f143 upstream.
Introduce new macros for kernel load/store variants which will be
used to perform regular kernel space load/store operations in EVA
mode.
Signed-off-by: Markos Chandras <markos.chandras@imgtec.com>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/9500/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit f7f8aea4b97c4d48e42f02cb37026bee445f239f upstream.
memsize denotes the amount of RAM we can access from kseg{0,1} and
that should be up to 256M. In case the bootloader reports a value
higher than that (perhaps reporting all the available RAM) it's best
if we fix it ourselves and just warn the user about that. This is
usually a problem with the bootloader and/or its environment.
[ralf@linux-mips.org: Remove useless parens as suggested bei Sergei.
Reformat long pr_warn statement to fit into 80 column limit.]
Signed-off-by: Markos Chandras <markos.chandras@imgtec.com>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/9362/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit acaf6a97d623af123314c2f8ce4cf7254f6b2fc1 upstream.
The lose_fpu() function only disables the FPU in CP0_Status.CU1 if the
FPU is in use and MSA isn't enabled.
This isn't necessarily a problem because KSTK_STATUS(current), the
version of CP0_Status stored on the kernel stack on entry from user
mode, does always get updated and gets restored when returning to user
mode, but I don't think it was intended, and it is inconsistent with the
case of only the FPU being in use. Sometimes leaving the FPU enabled may
also mask kernel bugs where FPU operations are executed when the FPU
might not be enabled.
So lets disable the FPU in the MSA case too.
Fixes: 33c771ba5c5d ("MIPS: save/disable MSA in lose_fpu")
Signed-off-by: James Hogan <james.hogan@imgtec.com>
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: Paul Burton <paul.burton@imgtec.com>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/9323/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 98119ad53376885819d93dfb8737b6a9a61ca0ba upstream.
Guest user mode can generate a guest MSA Disabled exception on an MSA
capable core by simply trying to execute an MSA instruction. Since this
exception is unknown to KVM it will be passed on to the guest kernel.
However guest Linux kernels prior to v3.15 do not set up an exception
handler for the MSA Disabled exception as they don't support any MSA
capable cores. This results in a guest OS panic.
Since an older processor ID may be being emulated, and MSA support is
not advertised to the guest, the correct behaviour is to generate a
Reserved Instruction exception in the guest kernel so it can send the
guest process an illegal instruction signal (SIGILL), as would happen
with a non-MSA-capable core.
Fix this as minimally as reasonably possible by preventing
kvm_mips_check_privilege() from relaying MSA Disabled exceptions from
guest user mode to the guest kernel, and handling the MSA Disabled
exception by emulating a Reserved Instruction exception in the guest,
via a new handle_msa_disabled() KVM callback.
Signed-off-by: James Hogan <james.hogan@imgtec.com>
Cc: Paolo Bonzini <pbonzini@redhat.com>
Cc: Paul Burton <paul.burton@imgtec.com>
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: Gleb Natapov <gleb@kernel.org>
Cc: linux-mips@linux-mips.org
Cc: kvm@vger.kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 085e68eeafbf76e21848ad5bafaecec88a11dd64 upstream.
The host's decision to enable machine check exceptions should remain
in force during non-root mode. KVM was writing 0 to cr4 on VCPU reset
and passed a slightly-modified 0 to the vmcs.guest_cr4 value.
Tested: Built.
On earlier version, tested by injecting machine check
while a guest is spinning.
Before the change, if guest CR4.MCE==0, then the machine check is
escalated to Catastrophic Error (CATERR) and the machine dies.
If guest CR4.MCE==1, then the machine check causes VMEXIT and is
handled normally by host Linux. After the change, injecting a machine
check causes normal Linux machine check handling.
Signed-off-by: Ben Serebrin <serebrin@google.com>
Reviewed-by: Venkatesh Srinivas <venkateshs@google.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit fd1d0ddf2ae92fb3df42ed476939861806c5d785 upstream.
When userland injects a SPI via the KVM_IRQ_LINE ioctl we currently
only check it against a fixed limit, which historically is set
to 127. With the new dynamic IRQ allocation the effective limit may
actually be smaller (64).
So when now a malicious or buggy userland injects a SPI in that
range, we spill over on our VGIC bitmaps and bytemaps memory.
I could trigger a host kernel NULL pointer dereference with current
mainline by injecting some bogus IRQ number from a hacked kvmtool:
-----------------
....
DEBUG: kvm_vgic_inject_irq(kvm, cpu=0, irq=114, level=1)
DEBUG: vgic_update_irq_pending(kvm, cpu=0, irq=114, level=1)
DEBUG: IRQ #114 still in the game, writing to bytemap now...
Unable to handle kernel NULL pointer dereference at virtual address 00000000
pgd = ffffffc07652e000
[00000000] *pgd=00000000f658b003, *pud=00000000f658b003, *pmd=0000000000000000
Internal error: Oops: 96000006 [#1] PREEMPT SMP
Modules linked in:
CPU: 1 PID: 1053 Comm: lkvm-msi-irqinj Not tainted 4.0.0-rc7+ #3027
Hardware name: FVP Base (DT)
task: ffffffc0774e9680 ti: ffffffc0765a8000 task.ti: ffffffc0765a8000
PC is at kvm_vgic_inject_irq+0x234/0x310
LR is at kvm_vgic_inject_irq+0x30c/0x310
pc : [<ffffffc0000ae0a8>] lr : [<ffffffc0000ae180>] pstate: 80000145
.....
So this patch fixes this by checking the SPI number against the
actual limit. Also we remove the former legacy hard limit of
127 in the ioctl code.
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Reviewed-by: Christoffer Dall <christoffer.dall@linaro.org>
[maz: wrap KVM_ARM_IRQ_GIC_MAX with #ifndef __KERNEL__,
as suggested by Christopher Covington]
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit ca3f0874723fad81d0c701b63ae3a17a408d5f25 upstream.
kvm_write_guest_cached() does not mark all written pages as dirty and
code comments in kvm_gfn_to_hva_cache_init() talk about NULL memslot
with cross page accesses. Fix all the easy way.
The check is '<= 1' to have the same result for 'len = 0' cache anywhere
in the page. (nr_pages_needed is 0 on page boundary.)
Fixes: 8f964525a121 ("KVM: Allow cross page reads and writes from cached translations.")
Signed-off-by: Radim Krčmář <rkrcmar@redhat.com>
Message-Id: <20150408121648.GA3519@potion.brq.redhat.com>
Reviewed-by: Wanpeng Li <wanpeng.li@linux.intel.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit d74419495633493c9cd3f2bbeb7f3529d0edded6 upstream.
Sebastian reported a crash caused by a jump label mismatch after resume.
This happens because we do not save the kernel text section during suspend
and therefore also do not restore it during resume, but use the kernel image
that restores the old system.
This means that after a suspend/resume cycle we lost all modifications done
to the kernel text section.
The reason for this is the pfn_is_nosave() function, which incorrectly
returns that read-only pages don't need to be saved. This is incorrect since
we mark the kernel text section read-only.
We still need to make sure to not save and restore pages contained within
NSS and DCSS segment.
To fix this add an extra case for the kernel text section and only save
those pages if they are not contained within an NSS segment.
Fixes the following crash (and the above bugs as well):
Jump label code mismatch at netif_receive_skb_internal+0x28/0xd0
Found: c0 04 00 00 00 00
Expected: c0 f4 00 00 00 11
New: c0 04 00 00 00 00
Kernel panic - not syncing: Corrupted kernel text
CPU: 0 PID: 9 Comm: migration/0 Not tainted 3.19.0-01975-gb1b096e70f23 #4
Call Trace:
[<0000000000113972>] show_stack+0x72/0xf0
[<000000000081f15e>] dump_stack+0x6e/0x90
[<000000000081c4e8>] panic+0x108/0x2b0
[<000000000081be64>] jump_label_bug.isra.2+0x104/0x108
[<0000000000112176>] __jump_label_transform+0x9e/0xd0
[<00000000001121e6>] __sm_arch_jump_label_transform+0x3e/0x50
[<00000000001d1136>] multi_cpu_stop+0x12e/0x170
[<00000000001d1472>] cpu_stopper_thread+0xb2/0x168
[<000000000015d2ac>] smpboot_thread_fn+0x134/0x1b0
[<0000000000158baa>] kthread+0x10a/0x110
[<0000000000824a86>] kernel_thread_starter+0x6/0xc
Reported-and-tested-by: Sebastian Ott <sebott@linux.vnet.ibm.com>
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 94aa033efcac47b09db22cb561e135baf37b7887 upstream.
This fixes a bug introduced with commit c05c4186bbe4 ("KVM: s390:
add floating irq controller").
get_all_floating_irqs() does copy_to_user() while holding
a spin lock. Let's fix this by filling a temporary buffer
first and copy it to userspace after giving up the lock.
Reviewed-by: David Hildenbrand <dahi@linux.vnet.ibm.com>
Signed-off-by: Jens Freimann <jfrei@linux.vnet.ibm.com>
Signed-off-by: Christian Borntraeger <borntraeger@de.ibm.com>
Acked-by: Cornelia Huck <cornelia.huck@de.ibm.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit b75f4c9afac2604feb971441116c07a24ecca1ec upstream.
s390 documentation requires words 0 and 10-15 to be reserved and stored as
zeros. As we fill out all other fields, we can memset the full structure.
Signed-off-by: Ekaterina Tumanova <tumanova@linux.vnet.ibm.com>
Reviewed-by: David Hildenbrand <dahi@linux.vnet.ibm.com>
Signed-off-by: Christian Borntraeger <borntraeger@de.ibm.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 15462e37ca848abac7477dece65f8af25febd744 upstream.
The reinjection of an I/O interrupt can fail if the list is at the limit
and between the dequeue and the reinjection, another I/O interrupt is
injected (e.g. if user space floods kvm with I/O interrupts).
This patch avoids this memory leak and returns -EFAULT in this special
case. This error is not recoverable, so let's fail hard. This can later
be avoided by not dequeuing the interrupt but working directly on the
locked list.
Signed-off-by: David Hildenbrand <dahi@linux.vnet.ibm.com>
Signed-off-by: Christian Borntraeger <borntraeger@de.ibm.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 261520dcfcba93ca5dfe671b88ffab038cd940c8 upstream.
If the I/O interrupt could not be written to the guest provided
area (e.g. access exception), a program exception was injected into the
guest but "inti" wasn't freed, therefore resulting in a memory leak.
In addition, the I/O interrupt wasn't reinjected. Therefore the dequeued
interrupt is lost.
This patch fixes the problem while cleaning up the function and making the
cc and rc logic easier to handle.
Signed-off-by: David Hildenbrand <dahi@linux.vnet.ibm.com>
Signed-off-by: Christian Borntraeger <borntraeger@de.ibm.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit eb132ccbdec5df46e29c9814adf76075ce83576b upstream.
Function-specific setup requests should be handled in such a way, that
apart from filling in the data buffer, the requests are also actually
enqueued: if function-specific setup is called from composte_setup(),
the "usb_ep_queue()" block of code in composite_setup() is skipped.
The printer function lacks this part and it results in e.g. get device id
requests failing: the host expects some response, the device prepares it
but does not equeue it for sending to the host, so the host finally asserts
timeout.
This patch adds enqueueing the prepared responses.
Fixes: 2e87edf49227: "usb: gadget: make g_printer use composite"
Signed-off-by: Andrzej Pietrasiewicz <andrzej.p@samsung.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 50c6a665b383cb5839e45d04e36faeeefaffa052 upstream.
Commit dc6c9a35b66b5 ("mm: account pmd page tables to the process")
added a counter that is incremented whenever a PMD is allocated and
decremented whenever a PMD is freed. For hugepages on PPC, common code
is used to allocated PMDs, but arch-specific code is used to free PMDs.
This results in kernel output such as "BUG: non-zero nr_pmds on freeing
mm: 1" when using hugepages.
Update the PPC hugepage PMD freeing code to decrement the count, just
as the above commit did for free_pmd_range().
Fixes: dc6c9a35b66b5 ("mm: account pmd page tables to the process")
Signed-off-by: Scott Wood <scottwood@freescale.com>
Reviewed-by: Aneesh Kumar K.V <aneesh.kumar@linux.vnet.ibm.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 97534127012f0e396eddea4691f4c9b170aed74b upstream.
Commit 61f77eda9bbf ("mm/hugetlb: reduce arch dependent code around
follow_huge_*") broke follow_huge_pmd() on s390, where pmd and pte
layout differ and using pte_page() on a huge pmd will return wrong
results. Using pmd_page() instead fixes this.
All architectures that were touched by that commit have pmd_page()
defined, so this should not break anything on other architectures.
Fixes: 61f77eda "mm/hugetlb: reduce arch dependent code around follow_huge_*"
Signed-off-by: Gerald Schaefer <gerald.schaefer@de.ibm.com>
Acked-by: Naoya Horiguchi <n-horiguchi@ah.jp.nec.com>
Cc: Hugh Dickins <hughd@google.com>
Cc: Michal Hocko <mhocko@suse.cz>
Cc: Andrea Arcangeli <aarcange@redhat.com>
Cc: Martin Schwidefsky <schwidefsky@de.ibm.com>
Acked-by: David Rientjes <rientjes@google.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 113e8283869b9855c8b999796aadd506bbac155f upstream.
If we pass a length of 0 to the extent_same ioctl, we end up locking an
extent range with a start offset greater then its end offset (if the
destination file's offset is greater than zero). This results in a warning
from extent_io.c:insert_state through the following call chain:
btrfs_extent_same()
btrfs_double_lock()
lock_extent_range()
lock_extent(inode->io_tree, offset, offset + len - 1)
lock_extent_bits()
__set_extent_bit()
insert_state()
--> WARN_ON(end < start)
This leads to an infinite loop when evicting the inode. This is the same
problem that my previous patch titled
"Btrfs: fix inode eviction infinite loop after cloning into it" addressed
but for the extent_same ioctl instead of the clone ioctl.
Signed-off-by: Filipe Manana <fdmanana@suse.com>
Reviewed-by: Omar Sandoval <osandov@osandov.com>
Signed-off-by: Chris Mason <clm@fb.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit ccccf3d67294714af2d72a6fd6fd7d73b01c9329 upstream.
If we attempt to clone a 0 length region into a file we can end up
inserting a range in the inode's extent_io tree with a start offset
that is greater then the end offset, which triggers immediately the
following warning:
[ 3914.619057] WARNING: CPU: 17 PID: 4199 at fs/btrfs/extent_io.c:435 insert_state+0x4b/0x10b [btrfs]()
[ 3914.620886] BTRFS: end < start 4095 4096
(...)
[ 3914.638093] Call Trace:
[ 3914.638636] [<ffffffff81425fd9>] dump_stack+0x4c/0x65
[ 3914.639620] [<ffffffff81045390>] warn_slowpath_common+0xa1/0xbb
[ 3914.640789] [<ffffffffa03ca44f>] ? insert_state+0x4b/0x10b [btrfs]
[ 3914.642041] [<ffffffff810453f0>] warn_slowpath_fmt+0x46/0x48
[ 3914.643236] [<ffffffffa03ca44f>] insert_state+0x4b/0x10b [btrfs]
[ 3914.644441] [<ffffffffa03ca729>] __set_extent_bit+0x107/0x3f4 [btrfs]
[ 3914.645711] [<ffffffffa03cb256>] lock_extent_bits+0x65/0x1bf [btrfs]
[ 3914.646914] [<ffffffff8142b2fb>] ? _raw_spin_unlock+0x28/0x33
[ 3914.648058] [<ffffffffa03cbac4>] ? test_range_bit+0xcc/0xde [btrfs]
[ 3914.650105] [<ffffffffa03cb3c3>] lock_extent+0x13/0x15 [btrfs]
[ 3914.651361] [<ffffffffa03db39e>] lock_extent_range+0x3d/0xcd [btrfs]
[ 3914.652761] [<ffffffffa03de1fe>] btrfs_ioctl_clone+0x278/0x388 [btrfs]
[ 3914.654128] [<ffffffff811226dd>] ? might_fault+0x58/0xb5
[ 3914.655320] [<ffffffffa03e0909>] btrfs_ioctl+0xb51/0x2195 [btrfs]
(...)
[ 3914.669271] ---[ end trace 14843d3e2e622fc1 ]---
This later makes the inode eviction handler enter an infinite loop that
keeps dumping the following warning over and over:
[ 3915.117629] WARNING: CPU: 22 PID: 4228 at fs/btrfs/extent_io.c:435 insert_state+0x4b/0x10b [btrfs]()
[ 3915.119913] BTRFS: end < start 4095 4096
(...)
[ 3915.137394] Call Trace:
[ 3915.137913] [<ffffffff81425fd9>] dump_stack+0x4c/0x65
[ 3915.139154] [<ffffffff81045390>] warn_slowpath_common+0xa1/0xbb
[ 3915.140316] [<ffffffffa03ca44f>] ? insert_state+0x4b/0x10b [btrfs]
[ 3915.141505] [<ffffffff810453f0>] warn_slowpath_fmt+0x46/0x48
[ 3915.142709] [<ffffffffa03ca44f>] insert_state+0x4b/0x10b [btrfs]
[ 3915.143849] [<ffffffffa03ca729>] __set_extent_bit+0x107/0x3f4 [btrfs]
[ 3915.145120] [<ffffffffa038c1e3>] ? btrfs_kill_super+0x17/0x23 [btrfs]
[ 3915.146352] [<ffffffff811548f6>] ? deactivate_locked_super+0x3b/0x50
[ 3915.147565] [<ffffffffa03cb256>] lock_extent_bits+0x65/0x1bf [btrfs]
[ 3915.148785] [<ffffffff8142b7e2>] ? _raw_write_unlock+0x28/0x33
[ 3915.149931] [<ffffffffa03bc325>] btrfs_evict_inode+0x196/0x482 [btrfs]
[ 3915.151154] [<ffffffff81168904>] evict+0xa0/0x148
[ 3915.152094] [<ffffffff811689e5>] dispose_list+0x39/0x43
[ 3915.153081] [<ffffffff81169564>] evict_inodes+0xdc/0xeb
[ 3915.154062] [<ffffffff81154418>] generic_shutdown_super+0x49/0xef
[ 3915.155193] [<ffffffff811546d1>] kill_anon_super+0x13/0x1e
[ 3915.156274] [<ffffffffa038c1e3>] btrfs_kill_super+0x17/0x23 [btrfs]
(...)
[ 3915.167404] ---[ end trace 14843d3e2e622fc2 ]---
So just bail out of the clone ioctl if the length of the region to clone
is zero, without locking any extent range, in order to prevent this issue
(same behaviour as a pwrite with a 0 length for example).
This is trivial to reproduce. For example, the steps for the test I just
made for fstests:
mkfs.btrfs -f SCRATCH_DEV
mount SCRATCH_DEV $SCRATCH_MNT
touch $SCRATCH_MNT/foo
touch $SCRATCH_MNT/bar
$CLONER_PROG -s 0 -d 4096 -l 0 $SCRATCH_MNT/foo $SCRATCH_MNT/bar
umount $SCRATCH_MNT
A test case for fstests follows soon.
Signed-off-by: Filipe Manana <fdmanana@suse.com>
Reviewed-by: Omar Sandoval <osandov@osandov.com>
Signed-off-by: Chris Mason <clm@fb.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 3c3b04d10ff1811a27f86684ccd2f5ba6983211d upstream.
Due to insufficient check in btrfs_is_valid_xattr, this unexpectedly
works:
$ touch file
$ setfattr -n user. -v 1 file
$ getfattr -d file
user.="1"
ie. the missing attribute name after the namespace.
Bugzilla: https://bugzilla.kernel.org/show_bug.cgi?id=94291
Reported-by: William Douglas <william.douglas@intel.com>
Signed-off-by: David Sterba <dsterba@suse.cz>
Signed-off-by: Chris Mason <clm@fb.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit dcc82f4783ad91d4ab654f89f37ae9291cdc846a upstream.
While committing a transaction we free the log roots before we write the
new super block. Freeing the log roots implies marking the disk location
of every node/leaf (metadata extent) as pinned before the new super block
is written. This is to prevent the disk location of log metadata extents
from being reused before the new super block is written, otherwise we
would have a corrupted log tree if before the new super block is written
a crash/reboot happens and the location of any log tree metadata extent
ended up being reused and rewritten.
Even though we pinned the log tree's metadata extents, we were issuing a
discard against them if the fs was mounted with the -o discard option,
resulting in corruption of the log tree if a crash/reboot happened before
writing the new super block - the next time the fs was mounted, during
the log replay process we would find nodes/leafs of the log btree with
a content full of zeroes, causing the process to fail and require the
use of the tool btrfs-zero-log to wipeout the log tree (and all data
previously fsynced becoming lost forever).
Fix this by not doing a discard when pinning an extent. The discard will
be done later when it's safe (after the new super block is committed) at
extent-tree.c:btrfs_finish_extent_commit().
Fixes: e688b7252f78 (Btrfs: fix extent pinning bugs in the tree log)
Signed-off-by: Filipe Manana <fdmanana@suse.com>
Signed-off-by: Chris Mason <clm@fb.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 9e9c3fe40bcd28e3f98f0ad8408435f4503f2781 upstream.
kvm_init_msr_list is currently called before hardware_setup. As a result,
vmx_mpx_supported always returns false when kvm_init_msr_list checks whether to
save MSR_IA32_BNDCFGS.
Move kvm_init_msr_list after vmx_hardware_setup is called to fix this issue.
Signed-off-by: Nadav Amit <namit@cs.technion.ac.il>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Message-Id: <1428864435-4732-1-git-send-email-namit@cs.technion.ac.il>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
|
|
commit d869844bd081081bf537e806a44811884230643e upstream.
Commit cae2a173fe94 ("x86: clean up/fix 'copy_in_user()' tail zeroing")
fixed the failure case tail zeroing of one special case of the x86-64
generic user-copy routine, namely when used for the user-to-user case
("copy_in_user()").
But in the process it broke an even more unusual case: using the user
copy routine for kernel-to-kernel copying.
Now, normally kernel-kernel copies are obviously done using memcpy(),
but we have a couple of special cases when we use the user-copy
functions. One is when we pass a kernel buffer to a regular user-buffer
routine, using set_fs(KERNEL_DS). That's a "normal" case, and continued
to work fine, because it never takes any faults (with the possible
exception of a silent and successful vmalloc fault).
But Jan Beulich pointed out another, very unusual, special case: when we
use the user-copy routines not because it's a path that expects a user
pointer, but for a couple of ftrace/kgdb cases that want to do a kernel
copy, but do so using "unsafe" buffers, and use the user-copy routine to
gracefully handle faults. IOW, for probe_kernel_write().
And that broke for the case of a faulting kernel destination, because we
saw the kernel destination and wanted to try to clear the tail of the
buffer. Which doesn't work, since that's what faults.
This only triggers for things like kgdb and ftrace users (eg trying
setting a breakpoint on read-only memory), but it's definitely a bug.
The fix is to not compare against the kernel address start (TASK_SIZE),
but instead use the same limits "access_ok()" uses.
Reported-and-tested-by: Jan Beulich <jbeulich@suse.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 517e6341fa123ec3a2f9ea78ad547be910529881 upstream.
Ingo reported that cycles:pp didn't work for him on some machines.
It turns out that in this commit:
af4bdcf675cf perf/x86/intel: Disallow flags for most Core2/Atom/Nehalem/Westmere events
Andi forgot to explicitly allow that event when he
disabled event flags for PEBS on those uarchs.
Reported-by: Ingo Molnar <mingo@kernel.org>
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Cc: Arnaldo Carvalho de Melo <acme@redhat.com>
Cc: Jiri Olsa <jolsa@redhat.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Fixes: af4bdcf675cf ("perf/x86/intel: Disallow flags for most Core2/Atom/Nehalem/Westmere events")
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit f8e617f4582995f7c25ef25b4167213120ad122b upstream.
To fully take advantage of MWAIT, apparently the CLFLUSH instruction needs
another quirk on certain CPUs: proper barriers around it on certain machines.
On a Q6600 SMP system, pipe-test scheduling performance, cross core,
improves significantly:
3.8.13 487.2 KHz 1.000
3.13.0-master 415.5 KHz .852
3.13.0-master+ 415.2 KHz .852 + restore mwait_idle
3.13.0-master++ 488.5 KHz 1.002 + restore mwait_idle + IPI fix
Since X86_BUG_CLFLUSH_MONITOR is already a quirk, don't create a separate
quirk for the extra smp_mb()s.
Signed-off-by: Mike Galbraith <bitbucket@online.de>
Cc: Borislav Petkov <bp@alien8.de>
Cc: H. Peter Anvin <hpa@zytor.com>
Cc: Ian Malone <ibmalone@gmail.com>
Cc: Josh Boyer <jwboyer@redhat.com>
Cc: Len Brown <len.brown@intel.com>
Cc: Len Brown <lenb@kernel.org>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Mike Galbraith <efault@gmx.de>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Link: http://lkml.kernel.org/r/1390061684.5566.4.camel@marge.simpson.net
[ Ported to recent kernel, added comments about the quirk. ]
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
savings and to improve performance
commit b253149b843f89cd300cbdbea27ce1f847506f99 upstream.
In Linux-3.9 we removed the mwait_idle() loop:
69fb3676df33 ("x86 idle: remove mwait_idle() and "idle=mwait" cmdline param")
The reasoning was that modern machines should be sufficiently
happy during the boot process using the default_idle() HALT
loop, until cpuidle loads and either acpi_idle or intel_idle
invoke the newer MWAIT-with-hints idle loop.
But two machines reported problems:
1. Certain Core2-era machines support MWAIT-C1 and HALT only.
MWAIT-C1 is preferred for optimal power and performance.
But if they support just C1, cpuidle never loads and
so they use the boot-time default idle loop forever.
2. Some laptops will boot-hang if HALT is used,
but will boot successfully if MWAIT is used.
This appears to be a hidden assumption in BIOS SMI,
that is presumably valid on the proprietary OS
where the BIOS was validated.
https://bugzilla.kernel.org/show_bug.cgi?id=60770
So here we effectively revert the patch above, restoring
the mwait_idle() loop. However, we don't bother restoring
the idle=mwait cmdline parameter, since it appears to add
no value.
Maintainer notes:
For 3.9, simply revert 69fb3676df
for 3.10, patch -F3 applies, fuzz needed due to __cpuinit use in
context For 3.11, 3.12, 3.13, this patch applies cleanly
Tested-by: Mike Galbraith <bitbucket@online.de>
Signed-off-by: Len Brown <len.brown@intel.com>
Acked-by: Mike Galbraith <bitbucket@online.de>
Cc: Borislav Petkov <bp@alien8.de>
Cc: H. Peter Anvin <hpa@zytor.com>
Cc: Ian Malone <ibmalone@gmail.com>
Cc: Josh Boyer <jwboyer@redhat.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Mike Galbraith <efault@gmx.de>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Link: http://lkml.kernel.org/r/345254a551eb5a6a866e048d7ab570fd2193aca4.1389763084.git.len.brown@intel.com
[ Ported to recent kernels. ]
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 80f7fdb1c7f0f9266421f823964fd1962681f6ce upstream.
If we were migrated right after __getcpu, but before reading the
migration_count, we wouldn't notice that we read TSC of a different
VCPU, nor that KVM's bug made pvti invalid, as only migration_count
on source VCPU is increased.
Change vdso instead of updating migration_count on destination.
Signed-off-by: Radim Krčmář <rkrcmar@redhat.com>
Fixes: 0a4e6be9ca17 ("x86: kvm: Revert "remove sched notifier for cross-cpu migrations"")
Message-Id: <1428000263-11892-1-git-send-email-rkrcmar@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 0a4e6be9ca17c54817cf814b4b5aa60478c6df27 upstream.
The following point:
2. per-CPU pvclock time info is updated if the
underlying CPU changes.
Is not true anymore since "KVM: x86: update pvclock area conditionally,
on cpu migration".
Add task migration notification back.
Problem noticed by Andy Lutomirski.
Signed-off-by: Marcelo Tosatti <mtosatti@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 91e5ed49fca09c2b83b262b9757d1376ee2b46c3 upstream.
x86 instructions cannot exceed 15 bytes, and the instruction
decoder should enforce that. Prior to 6ba48ff46f76, the
instruction length limit was implicitly set to 16, which was an
approximation of 15, but there is currently no limit at all.
Fix MAX_INSN_SIZE (it should be 15, not 16), and fix the decoder
to reject instructions that exceed MAX_INSN_SIZE.
Other than potentially confusing some of the decoder sanity
checks, I'm not aware of any actual problems that omitting this
check would cause, nor am I aware of any practical problems
caused by the MAX_INSN_SIZE error.
Signed-off-by: Andy Lutomirski <luto@amacapital.net>
Acked-by: Masami Hiramatsu <masami.hiramatsu.pt@hitachi.com>
Cc: Dave Hansen <dave.hansen@linux.intel.com>
Fixes: 6ba48ff46f76 ("x86: Remove arbitrary instruction size limit ...
Link: http://lkml.kernel.org/r/f8f0bc9b8c58cfd6830f7d88400bf1396cbdcd0f.1422403511.git.luto@amacapital.net
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 74672d069b298b03e9f657fd70915e055739882e upstream.
Simon reported the md io stats accounting issue:
"
I'm seeing "iostat -x -k 1" print this after a RAID1 rebuild on 4.0-rc5.
It's not abnormal other than it's 3-disk, with one being SSD (sdc) and
the other two being write-mostly:
Device: rrqm/s wrqm/s r/s w/s rkB/s wkB/s avgrq-sz avgqu-sz await r_await w_await svctm %util
sda 0.00 0.00 0.00 0.00 0.00 0.00 0.00 0.00 0.00 0.00 0.00 0.00 0.00
sdb 0.00 0.00 0.00 0.00 0.00 0.00 0.00 0.00 0.00 0.00 0.00 0.00 0.00
sdc 0.00 0.00 0.00 0.00 0.00 0.00 0.00 0.00 0.00 0.00 0.00 0.00 0.00
md0 0.00 0.00 0.00 0.00 0.00 0.00 0.00 345.00 0.00 0.00 0.00 0.00 100.00
md2 0.00 0.00 0.00 0.00 0.00 0.00 0.00 58779.00 0.00 0.00 0.00 0.00 100.00
md1 0.00 0.00 0.00 0.00 0.00 0.00 0.00 12.00 0.00 0.00 0.00 0.00 100.00
"
The cause is commit "18c0b223cf9901727ef3b02da6711ac930b4e5d4" uses the
generic_start_io_acct to account the disk stats rather than the open code,
but it also introduced the increase to .in_flight[rw] which is needless to
md. So we re-use the open code here to fix it.
Reported-by: Simon Kirby <sim@hostway.ca>
Signed-off-by: Gu Zheng <guz.fnst@cn.fujitsu.com>
Signed-off-by: NeilBrown <neilb@suse.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
[ Upstream commit b37069090b7c5615610a8aa6b36533d67b364d38 ]
mlx4_en_check_rxfh_func() was checking for hardware support before
setting a known RSS hash function, but didn't do any check before
setting unknown RSS hash function. Need to make it fail on such values.
In this occasion, moved the actual setting of the new value from the
check function into mlx4_en_set_rxfh().
Fixes: 947cbb0 ("net/mlx4_en: Support for configurable RSS hash function")
Signed-off-by: Amir Vadai <amirv@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
[ Upstream commit a31196b07f8034eba6a3487a1ad1bb5ec5cd58a5 ]
Commit 567e4b79731c ("net: rfs: add hash collision detection") had one
mistake :
RPS_NO_CPU is no longer the marker for invalid cpu in set_rps_cpu()
and get_rps_cpu(), as @next_cpu was the result of an AND with
rps_cpu_mask
This bug showed up on a host with 72 cpus :
next_cpu was 0x7f, and the code was trying to access percpu data of an
non existent cpu.
In a follow up patch, we might get rid of compares against nr_cpu_ids,
if we init the tables with 0. This is silly to test for a very unlikely
condition that exists only shortly after table initialization, as
we got rid of rps_reset_sock_flow() and similar functions that were
writing this RPS_NO_CPU magic value at flow dismantle : When table is
old enough, it never contains this value anymore.
Fixes: 567e4b79731c ("net: rfs: add hash collision detection")
Signed-off-by: Eric Dumazet <edumazet@google.com>
Cc: Tom Herbert <tom@herbertland.com>
Cc: Ben Hutchings <ben@decadent.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
[ Upstream commit 0e03fd3e335d272bee88fe733d5fd13f5c5b7140 ]
Commit 43d3ddf87a57 ("net: pxa168_eth: add device tree support") starts
to use managed resources by adding devm_clk_get() and
devm_ioremap_resource(), but it leaves explicit iounmap() and clock_put()
in pxa168_eth_remove() and in failure handling code of pxa168_eth_probe().
As a result double free can happen.
The patch removes explicit resource deallocation. Also it converts
clk_disable() to clk_disable_unprepare() to make it symmetrical with
clk_prepare_enable().
Found by Linux Driver Verification project (linuxtesting.org).
Signed-off-by: Alexey Khoroshilov <khoroshilov@ispras.ru>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
[ Upstream commit 2ea2f62c8bda242433809c7f4e9eae1c52c40bbe ]
When I added pfmemalloc support in build_skb(), I forgot netlink
was using build_skb() with a vmalloc() area.
In this patch I introduce __build_skb() for netlink use,
and build_skb() is a wrapper handling both skb->head_frag and
skb->pfmemalloc
This means netlink no longer has to hack skb->head_frag
[ 1567.700067] kernel BUG at arch/x86/mm/physaddr.c:26!
[ 1567.700067] invalid opcode: 0000 [#1] PREEMPT SMP KASAN
[ 1567.700067] Dumping ftrace buffer:
[ 1567.700067] (ftrace buffer empty)
[ 1567.700067] Modules linked in:
[ 1567.700067] CPU: 9 PID: 16186 Comm: trinity-c182 Not tainted 4.0.0-next-20150424-sasha-00037-g4796e21 #2167
[ 1567.700067] task: ffff880127efb000 ti: ffff880246770000 task.ti: ffff880246770000
[ 1567.700067] RIP: __phys_addr (arch/x86/mm/physaddr.c:26 (discriminator 3))
[ 1567.700067] RSP: 0018:ffff8802467779d8 EFLAGS: 00010202
[ 1567.700067] RAX: 000041000ed8e000 RBX: ffffc9008ed8e000 RCX: 000000000000002c
[ 1567.700067] RDX: 0000000000000004 RSI: 0000000000000000 RDI: ffffffffb3fd6049
[ 1567.700067] RBP: ffff8802467779f8 R08: 0000000000000019 R09: ffff8801d0168000
[ 1567.700067] R10: ffff8801d01680c7 R11: ffffed003a02d019 R12: ffffc9000ed8e000
[ 1567.700067] R13: 0000000000000f40 R14: 0000000000001180 R15: ffffc9000ed8e000
[ 1567.700067] FS: 00007f2a7da3f700(0000) GS:ffff8801d1000000(0000) knlGS:0000000000000000
[ 1567.700067] CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033
[ 1567.700067] CR2: 0000000000738308 CR3: 000000022e329000 CR4: 00000000000007e0
[ 1567.700067] Stack:
[ 1567.700067] ffffc9000ed8e000 ffff8801d0168000 ffffc9000ed8e000 ffff8801d0168000
[ 1567.700067] ffff880246777a28 ffffffffad7c0a21 0000000000001080 ffff880246777c08
[ 1567.700067] ffff88060d302e68 ffff880246777b58 ffff880246777b88 ffffffffad9a6821
[ 1567.700067] Call Trace:
[ 1567.700067] build_skb (include/linux/mm.h:508 net/core/skbuff.c:316)
[ 1567.700067] netlink_sendmsg (net/netlink/af_netlink.c:1633 net/netlink/af_netlink.c:2329)
[ 1567.774369] ? sched_clock_cpu (kernel/sched/clock.c:311)
[ 1567.774369] ? netlink_unicast (net/netlink/af_netlink.c:2273)
[ 1567.774369] ? netlink_unicast (net/netlink/af_netlink.c:2273)
[ 1567.774369] sock_sendmsg (net/socket.c:614 net/socket.c:623)
[ 1567.774369] sock_write_iter (net/socket.c:823)
[ 1567.774369] ? sock_sendmsg (net/socket.c:806)
[ 1567.774369] __vfs_write (fs/read_write.c:479 fs/read_write.c:491)
[ 1567.774369] ? get_lock_stats (kernel/locking/lockdep.c:249)
[ 1567.774369] ? default_llseek (fs/read_write.c:487)
[ 1567.774369] ? vtime_account_user (kernel/sched/cputime.c:701)
[ 1567.774369] ? rw_verify_area (fs/read_write.c:406 (discriminator 4))
[ 1567.774369] vfs_write (fs/read_write.c:539)
[ 1567.774369] SyS_write (fs/read_write.c:586 fs/read_write.c:577)
[ 1567.774369] ? SyS_read (fs/read_write.c:577)
[ 1567.774369] ? __this_cpu_preempt_check (lib/smp_processor_id.c:63)
[ 1567.774369] ? trace_hardirqs_on_caller (kernel/locking/lockdep.c:2594 kernel/locking/lockdep.c:2636)
[ 1567.774369] ? trace_hardirqs_on_thunk (arch/x86/lib/thunk_64.S:42)
[ 1567.774369] system_call_fastpath (arch/x86/kernel/entry_64.S:261)
Fixes: 79930f5892e ("net: do not deplete pfmemalloc reserve")
Signed-off-by: Eric Dumazet <edumazet@google.com>
Reported-by: Sasha Levin <sasha.levin@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
[ Upstream commit 79930f5892e134c6da1254389577fffb8bd72c66 ]
build_skb() should look at the page pfmemalloc status.
If set, this means page allocator allocated this page in the
expectation it would help to free other pages. Networking
stack can do that only if skb->pfmemalloc is also set.
Also, we must refrain using high order pages from the pfmemalloc
reserve, so __page_frag_refill() must also use __GFP_NOMEMALLOC for
them. Under memory pressure, using order-0 pages is probably the best
strategy.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
[ Upstream commit 845704a535e9b3c76448f52af1b70e4422ea03fd ]
Presence of an unbound loop in tcp_send_fin() had always been hard
to explain when analyzing crash dumps involving gigantic dying processes
with millions of sockets.
Lets try a different strategy :
In case of memory pressure, try to add the FIN flag to last packet
in write queue, even if packet was already sent. TCP stack will
be able to deliver this FIN after a timeout event. Note that this
FIN being delivered by a retransmit, it also carries a Push flag
given our current implementation.
By checking sk_under_memory_pressure(), we anticipate that cooking
many FIN packets might deplete tcp memory.
In the case we could not allocate a packet, even with __GFP_WAIT
allocation, then not sending a FIN seems quite reasonable if it allows
to get rid of this socket, free memory, and not block the process from
eventually doing other useful work.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
[ Upstream commit d83769a580f1132ac26439f50068a29b02be535e ]
Using sk_stream_alloc_skb() in tcp_send_fin() is dangerous in
case a huge process is killed by OOM, and tcp_mem[2] is hit.
To be able to free memory we need to make progress, so this
patch allows FIN packets to not care about tcp_mem[2], if
skb allocation succeeded.
In a follow-up patch, we might abort tcp_send_fin() infinite loop
in case TIF_MEMDIE is set on this thread, as memory allocator
did its best getting extra memory already.
This patch reverts d22e15371811 ("tcp: fix tcp fin memory accounting")
Fixes: d22e15371811 ("tcp: fix tcp fin memory accounting")
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
