| Age | Commit message (Collapse) | Author |
|---|
|
commit 5727347180ebc6b4a866fcbe00dcb39cc03acb37 upstream.
On ARM, the PMU does not stop counting after an overflow and therefore
IRQ latency affects the new counter value read by the kernel. This is
significant for non-sampling runs where it is possible for the new value
to overtake the previous one, causing the delta to be out by up to
max_period events.
Commit a737823d ("ARM: 6835/1: perf: ensure overflows aren't missed due
to IRQ latency") attempted to fix this problem by allowing interrupt
handlers to pass an overflow flag to the event update function, causing
the overflow calculation to assume that the counter passed through zero
when going from prev to new. Unfortunately, this doesn't work when
overflow occurs on the perf_task_tick path because we have the flag
cleared and end up computing a large negative delta.
This patch removes the overflow flag from armpmu_event_update and
instead limits the sample_period to half of the max_period for
non-sampling profiling runs.
Signed-off-by: Ming Lei <ming.lei@canonical.com>
Signed-off-by: Will Deacon <will.deacon@arm.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit efbc74ace95338484f8d732037b99c7c77098fce upstream.
Erratum #743622 affects all r2 variants of the Cortex-A9 processor, so
ensure that the workaround is applied regardless of the revision.
Reported-by: Russell King <rmk+kernel@arm.linux.org.uk>
Signed-off-by: Will Deacon <will.deacon@arm.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit ca888a7958b3d808e4efd08ceff88913f4212c69 upstream.
The "OMAPDSS: HDMI: PHY burnout fix" commit switched the HDMI driver
over to using a GPIO for plug detect. Unfortunately the ->detect()
method was not also updated, causing HDMI to no longer work for the
omapdrm driver (because it would actually check if a connection was
detected before attempting to enable display).
Signed-off-by: Rob Clark <rob@ti.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit c49d005b6cc8491fad5b24f82805be2d6bcbd3dd upstream.
A hardware bug in the OMAP4 HDMI PHY causes physical damage to the board
if the HDMI PHY is kept powered on when the cable is not connected.
This patch solves the problem by adding hot-plug-detection into the HDMI
IP driver. This is not a real HPD support in the sense that nobody else
than the IP driver gets to know about the HPD events, but is only meant
to fix the HW bug.
The strategy is simple: If the display device is turned off by the user,
the PHY power is set to OFF. When the display device is turned on by the
user, the PHY power is set either to LDOON or TXON, depending on whether
the HDMI cable is connected.
The reason to avoid PHY OFF when the display device is on, but the cable
is disconnected, is that when the PHY is turned OFF, the HDMI IP is not
"ticking" and thus the DISPC does not receive pixel clock from the HDMI
IP. This would, for example, prevent any VSYNCs from happening, and
would thus affect the users of omapdss. By using LDOON when the cable is
disconnected we'll avoid the HW bug, but keep the HDMI working as usual
from the user's point of view.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit aa74274b464d4aa24703963ac89a0ee942d5d267 upstream.
Both Panda and 4430SDP use GPIO 63 as HDMI hot-plug-detect. Configure
this GPIO in the board files.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Acked-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 78a1ad8f12db70b8b0a4548b90704de08ee216ce upstream.
The HDMI GPIO pins LS_OE and CT_CP_HPD are not currently configured.
This patch configures them as output pins.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Acked-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 7bb122d155f742fe2d79849090c825be7b4a247e upstream.
"hdmi_hpd" pin is muxed to INPUT and PULLUP, but the pin is not
currently used, and in the future when it is used, the pin is used as a
GPIO and is board specific, not an OMAP4 wide thing.
So remove the muxing for now.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Acked-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 3932a32fcf5393f8be70ac99dc718ad7ad0a415b upstream.
The GPIO 60 on 4430sdp and Panda is not HPD GPIO, as currently marked in
the board files, but CT_CP_HPD, which is used to enable/disable HPD
functionality.
This patch renames the GPIO.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Acked-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 575753e3bea3b67eef8e454fb87f719e3f7da599 upstream.
Instead of freeing the GPIOs individually, use gpio_free_array().
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Acked-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit b06540371063f0f07aafc1d1ac5e974da85c973c upstream.
Patchset "ARM: orion: Refactor the MPP code common in the orion
platform" broke at least Orion5x based platforms. These platforms have
pins configured as GPIO when the selector is not 0x0. However the
common code assumes the selector is always 0x0 for a GPIO lines. It
then ignores the GPIO bits in the MPP definitions, resulting in that
Orion5x machines cannot correctly configure there GPIO lines.
The Fix removes the assumption that the selector is always 0x0.
In order that none GPIO configurations are correctly blocked,
Kirkwood and mv78xx0 MPP definitions are corrected to only set the
GPIO bits for GPIO configurations.
This third version, which does not contain any whitespace changes,
and is rebased on v3.3-rc2.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Acked-by: Nicolas Pitre <nico@linaro.org>
Signed-off-by: Olof Johansson <olof@lixom.net>
|
|
commit 72053353583230952c4b187e110e9da00dfc3afb upstream.
The patch "ARM: orion: Consolidate USB platform setup code.", commit
4fcd3f374a928081d391cd9a570afe3b2c692fdc broke USB on TS-7800 and
other orion5x boards, because the wrong type of PHY was being passed
to the EHCI driver in the platform data. Orion5x needs EHCI_PHY_ORION
and all the others want EHCI_PHY_NA.
Allow the mach- code to tell the generic plat-orion code which USB PHY
enum to place into the platform data.
Version 2: Rebase to v3.3-rc2.
Reported-by: Ambroz Bizjak <ambrop7@gmail.com>
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Tested-by: Ambroz Bizjak <ambrop7@gmail.com>
Acked-by: Nicolas Pitre <nico@linaro.org>
Signed-off-by: Olof Johansson <olof@lixom.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit b3f33cbf7ace8fc149993ee35e0d0fd57f41d6d8 upstream.
SandyBridge should be using the same register addresses as IvyBridge.
Signed-off-by: Wu Fengguang <fengguang.wu@intel.com>
Signed-off-by: Keith Packard <keithp@keithp.com>
Signed-off-by: Eugeni Dodonov <eugeni.dodonov@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit d71de14ddf423ccc9a2e3f7e37553c99ead20d7c upstream.
The BSpec Workarounds page states that bits 10 and 26 must be set to
avoid 3D ring hangs.
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=41353
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=44610
Tested-by: Eugeni Dodonov <eugeni.dodonov@intel.com>
Signed-off-by: Kenneth Graunke <kenneth@whitecape.org>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit db099c8f963fe656108e0a068274c5580a17f69b upstream.
This adds the workaround for WaCatErrorRejectionIssue which could result
in a system hang.
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=41353
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=44610
Tested-by: Eugeni Dodonov <eugeni.dodonov@intel.com>
Reviewed-by: Kenneth Graunke <kenneth@whitecape.org>
Signed-off-by: Eugeni Dodonov <eugeni.dodonov@intel.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit e4e0c058a19c41150d12ad2d3023b3cf09c5de67 upstream.
This adds two cache-related workarounds for Ivy Bridge which can lead to
3D ring hangs and corruptions.
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=41353
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=44610
Tested-by: Eugeni Dodonov <eugeni.dodonov@intel.com>
Signed-off-by: Eugeni Dodonov <eugeni.dodonov@intel.com>
Signed-off-by: Kenneth Graunke <kenneth@whitecape.org>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit eae66b50c760233fad526edf4a0d327be17a055d upstream.
This is yet another workaround related to clock gating which we need on
Ivy Bridge.
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=41353
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=44610
Tested-by: Eugeni Dodonov <eugeni.dodonov@intel.com>
Signed-off-by: Eugeni Dodonov <eugeni.dodonov@intel.com>
Signed-off-by: Kenneth Graunke <kenneth@whitecape.org>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 6cddafab54e9a17b2efefe982547865955a5ff3a upstream.
The latest vendor (non-mac80211) driver of 9/22/2011 shows some new
device IDs for rtl8192cu. In addition, some typos in the table are
fixed and one duplicate is removed.
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 5a50a7c32d630d6cdb13d69afabb0cc81b2f379c upstream.
The models do not resume correctly without acpi_sleep=nonvs.
Signed-off-by: Keng-Yu Lin <kengyu@canonical.com>
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Cc: Tim Gardner <tim.gardner@canonical.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 31e0017e6f6fb5cfdfaf932c1f98c9bef8d57688 upstream.
Enable use of the generic atomic64 implementation on AVR32 platforms.
Without this the kernel fails to build as the architecture does not
provide its version.
Signed-off-by: Fabio Baltieri <fabio.baltieri@gmail.com>
Acked-by: Hans-Christian Egtvedt <egtvedt@samfundet.no>
Cc: Haavard Skinnemoen <hskinnemoen@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 37b40adf2d1b4a5e51323be73ccf8ddcf3f15dd3 upstream.
We create "bsg" link if q->kobj.sd is not NULL, so remove it only
when the same condition is true.
Fixes:
WARNING: at fs/sysfs/inode.c:323 sysfs_hash_and_remove+0x2b/0x77()
sysfs: can not remove 'bsg', no directory
Call Trace:
[<c0429683>] warn_slowpath_common+0x6a/0x7f
[<c0537a68>] ? sysfs_hash_and_remove+0x2b/0x77
[<c042970b>] warn_slowpath_fmt+0x2b/0x2f
[<c0537a68>] sysfs_hash_and_remove+0x2b/0x77
[<c053969a>] sysfs_remove_link+0x20/0x23
[<c05d88f1>] bsg_unregister_queue+0x40/0x6d
[<c0692263>] __scsi_remove_device+0x31/0x9d
[<c069149f>] scsi_forget_host+0x41/0x52
[<c0689fa9>] scsi_remove_host+0x71/0xe0
[<f7de5945>] quiesce_and_remove_host+0x51/0x83 [usb_storage]
[<f7de5a1e>] usb_stor_disconnect+0x18/0x22 [usb_storage]
[<c06c29de>] usb_unbind_interface+0x4e/0x109
[<c067a80f>] __device_release_driver+0x6b/0xa6
[<c067a861>] device_release_driver+0x17/0x22
[<c067a46a>] bus_remove_device+0xd6/0xe6
[<c06785e2>] device_del+0xf2/0x137
[<c06c101f>] usb_disable_device+0x94/0x1a0
Signed-off-by: Stanislaw Gruszka <sgruszka@redhat.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Signed-off-by: Tim Gardner <tim.gardner@canonical.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 5ed80a75b248bfaf840ea6b38f941edcf6ee7dc7 upstream.
According to i.MX27 Reference Manual (p 1593) TXBIT0 bit selects
whether the most significant or the less significant part of the
data word written to the FIFO is transmitted.
As DSP_A is the same as DSP_B with a data offset of 1 bit, it
doesn't make any sense to remove TXBIT0 bit here.
Signed-off-by: Javier Martin <javier.martin@vista-silicon.com>
Acked-by: Sascha Hauer <s.hauer@pengutronix.de>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 7679e42ec833ed70aa34790a5f39dcb7e5bda4fe upstream.
Recent enhancements in the bias management means that we might not be
in standby when the CODEC is idle and can have active widgets without
being in full power mode but the shutdown functionality assumes these
things. Add checks for the bias level at each stage so that we don't
do transitions other than the ON->PREPARE->STANDBY->OFF ones that the
drivers are expecting.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit e29206381a1436e0f47c0f5b9a23159a03c57715 upstream.
Even if the documentation calls this bit "Reserved" it has to be set
to 0 for correct modesetting on IGA1.
Signed-off-by: Florian Tobias Schandinat <FlorianSchandinat@gmx.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 050f0e02c8dc38b2b4f2df345ac760d22ca5c7ba upstream.
VX900 can do hardware scaling for both IGAs in contrast to previous
hardware which could do it only for IGA2. This patch ensures that
we set the parameter for IGA2 and not for IGA1. This fixes hardware
scaling on VX900 until we have the infrastructure to support it for
both IGAs.
Signed-off-by: Florian Tobias Schandinat <FlorianSchandinat@gmx.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 41f8ad76362e7aefe3a03949c43e23102dae6e0b upstream.
It used to be that minors where 8 bit. But now they
are actually 20 bit. So the fix is simplicity itself.
I've tested with 300 devices and all user-mode utils
work just fine. I have also mechanically added 10,000
to the ida (so devices are /dev/osd10000, /dev/osd10001 ...)
and was able to mkfs an exofs filesystem and access osds
from user-mode.
All the open-osd user-mode code uses the same library
to access devices through their symbolic names in
/dev/osdX so I'd say it's pretty safe. (Well tested)
This patch is very important because some of the systems
that will be deploying the 3.2 pnfs-objects code are larger
than 64 OSDs and will stop to work properly when reaching
that number.
Signed-off-by: Boaz Harrosh <bharrosh@panasas.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit f8f54e190ddb4ed697036b60f5e2ae6dd45b801c upstream.
Broken by commit 6ef84509f3d439ed2d43ea40080643efec37f54f for users
passing a request with non-zero 'nbytes' field, like e.g. testmgr.
Signed-off-by: Phil Sutter <phil.sutter@viprinet.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 37891abc8464637964a26ae4b61d307fef831f80 upstream.
This patch (as1531) adds a NOGET quirk for the Slim+ keyboard marketed
by AIREN. This keyboard seems to have a lot of bugs; NOGET works
around only one of them.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Reported-by: okias <d.okias@gmail.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit b24823e61bfd93d0e72088e4f5245287582ed289 upstream.
Fix a bug that causes a kernel panic when the number of received doorbells
is larger than number of entries in the inbound doorbell queue (current
default value = 512).
Another possible indication for this bug is large number of spurious
doorbells reported by tsi721 driver after reaching the queue size maximum.
Signed-off-by: Alexandre Bounine <alexandre.bounine@idt.com>
Cc: Chul Kim <chul.kim@idt.com>
Cc: Matt Porter <mporter@kernel.crashing.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 7b3cc67d4445995a025a4b55a7dc687b6829b4ca upstream.
Git commit 25f269f17316549e "[S390] qdio: EQBS retry after CCQ 96"
introduced a regression in regard to the zfcp data router.
Revoke the incorrect simplification of the function call arguments
for the qdio handler to make the zfcp hardware data router working
again.
This is applicable to 3.2+ kernels.
Signed-off-by: Steffen Maier <maier@linux.vnet.ibm.com>
Reviewed-by: Jan Glauber <jang@linux.vnet.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit f21c6d4a49179f91fd70a41382382f08c780d425 upstream.
Fixes these build errors:
ERROR: ".udbg_printf" [drivers/tty/ehv_bytechan.ko] undefined!
ERROR: ".register_early_udbg_console" [drivers/tty/ehv_bytechan.ko] undefined!
ERROR: "udbg_putc" [drivers/tty/ehv_bytechan.ko] undefined!
Cc: Timur Tabi <timur@freescale.com>
Signed-off-by: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 5dcbf480473f6c3f06ad2426b7517038a2a18911 upstream.
When trying to remove a key, we always send key
flags just setting the key type, not including
the multicast flag and the key ID. As a result,
whenever any key was removed, the unicast key 0
would be removed, causing a complete connection
loss after the second rekey (the first doesn't
cause a key removal). Fix the key removal code
to include the key ID and multicast flag, thus
removing the correct key.
Reported-by: Alexander Schnaidt <alex.schnaidt@googlemail.com>
Tested-by: Alexander Schnaidt <alex.schnaidt@googlemail.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 1c641e84719429bbfe62a95ed3545ee7fe24408f upstream.
Dave Jones reports a few Fedora users hitting the BUG_ON(mm->nr_ptes...)
in exit_mmap() recently.
Quoting Hugh's discovery and explanation of the SMP race condition:
"mm->nr_ptes had unusual locking: down_read mmap_sem plus
page_table_lock when incrementing, down_write mmap_sem (or mm_users
0) when decrementing; whereas THP is careful to increment and
decrement it under page_table_lock.
Now most of those paths in THP also hold mmap_sem for read or write
(with appropriate checks on mm_users), but two do not: when
split_huge_page() is called by hwpoison_user_mappings(), and when
called by add_to_swap().
It's conceivable that the latter case is responsible for the
exit_mmap() BUG_ON mm->nr_ptes that has been reported on Fedora."
The simplest way to fix it without having to alter the locking is to make
split_huge_page() a noop in nr_ptes terms, so by counting the preallocated
pagetables that exists for every mapped hugepage. It was an arbitrary
choice not to count them and either way is not wrong or right, because
they are not used but they're still allocated.
Reported-by: Dave Jones <davej@redhat.com>
Reported-by: Hugh Dickins <hughd@google.com>
Signed-off-by: Andrea Arcangeli <aarcange@redhat.com>
Acked-by: Hugh Dickins <hughd@google.com>
Cc: David Rientjes <rientjes@google.com>
Cc: Josh Boyer <jwboyer@redhat.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit f986a499ef6f317d906e6f6f281be966e1237a10 upstream.
register_kprobe() aborts if the address of the new request falls in a
prohibited area (such as ftrace pouch, __kprobes annotated functions,
non-kernel text addresses, jump label text). We however don't return the
right error on this abort, resulting in a silent failure - incorrect
adding/reporting of kprobes ('perf probe do_fork+18' or 'perf probe
mcount' for instance).
In V2 we are incorporating Masami Hiramatsu's feedback.
This patch fixes it by returning -EINVAL upon failure.
While we are here, rename the label used for exit to be more appropriate.
Signed-off-by: Ananth N Mavinakayanahalli <ananth@in.ibm.com>
Signed-off-by: Prashanth K Nageshappa <prashanth@linux.vnet.ibm.com>
Acked-by: Masami Hiramatsu <masami.hiramatsu.pt@hitachi.com>
Cc: Jason Baron <jbaron@redhat.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 9bbb8168ed3d8b946f9c1901a63a675012de88f2 upstream.
Duplicate the data for iniAddac early on, to avoid having to do redundant
memcpy calls later. While we're at it, make AR5416 < v2.2 use the same
codepath. Fixes a reported crash on x86.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Reported-by: Magnus Määttä <magnus.maatta@logica.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 8617b093d0031837a7be9b32bc674580cfb5f6b5 upstream.
rate control algorithms concludes the rate as invalid
with rate[i].idx < -1 , while they do also check for rate[i].count is
non-zero. it would be safer to zero initialize the 'count' field.
recently we had a ath9k rate control crash where the ath9k rate control
in ath_tx_status assumed to check only for rate[i].count being non-zero
in one instance and ended up in using invalid rate index for
'connection monitoring NULL func frames' which eventually lead to the crash.
thanks to Pavel Roskin for fixing it and finding the root cause.
https://bugzilla.redhat.com/show_bug.cgi?id=768639
Cc: Pavel Roskin <proski@gnu.org>
Signed-off-by: Mohammed Shafi Shajakhan <mohammed@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 5bccda0ebc7c0331b81ac47d39e4b920b198b2cd upstream.
The cifs code will attempt to open files on lookup under certain
circumstances. What happens though if we find that the file we opened
was actually a FIFO or other special file?
Currently, the open filehandle just ends up being leaked leading to
a dentry refcount mismatch and oops on umount. Fix this by having the
code close the filehandle on the server if it turns out not to be a
regular file. While we're at it, change this spaghetti if statement
into a switch too.
Reported-by: CAI Qian <caiqian@redhat.com>
Tested-by: CAI Qian <caiqian@redhat.com>
Reviewed-by: Shirish Pargaonkar <shirishpargaonkar@gmail.com>
Signed-off-by: Jeff Layton <jlayton@redhat.com>
Signed-off-by: Steve French <smfrench@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit b94cfaf6685d691dc3fab023cf32f65e9b7be09c upstream.
Don't clear vm_mm in a deleted VMA as it's unnecessary and might
conceivably break the filesystem or driver VMA close routine.
Reported-by: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: David Howells <dhowells@redhat.com>
Acked-by: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 371528caec553785c37f73fa3926ea0de84f986f upstream.
There is an issue when memcg unregisters events that were attached to
the same eventfd:
- On the first call mem_cgroup_usage_unregister_event() removes all
events attached to a given eventfd, and if there were no events left,
thresholds->primary would become NULL;
- Since there were several events registered, cgroups core will call
mem_cgroup_usage_unregister_event() again, but now kernel will oops,
as the function doesn't expect that threshold->primary may be NULL.
That's a good question whether mem_cgroup_usage_unregister_event()
should actually remove all events in one go, but nowadays it can't
do any better as cftype->unregister_event callback doesn't pass
any private event-associated cookie. So, let's fix the issue by
simply checking for threshold->primary.
FWIW, w/o the patch the following oops may be observed:
BUG: unable to handle kernel NULL pointer dereference at 0000000000000004
IP: [<ffffffff810be32c>] mem_cgroup_usage_unregister_event+0x9c/0x1f0
Pid: 574, comm: kworker/0:2 Not tainted 3.3.0-rc4+ #9 Bochs Bochs
RIP: 0010:[<ffffffff810be32c>] [<ffffffff810be32c>] mem_cgroup_usage_unregister_event+0x9c/0x1f0
RSP: 0018:ffff88001d0b9d60 EFLAGS: 00010246
Process kworker/0:2 (pid: 574, threadinfo ffff88001d0b8000, task ffff88001de91cc0)
Call Trace:
[<ffffffff8107092b>] cgroup_event_remove+0x2b/0x60
[<ffffffff8103db94>] process_one_work+0x174/0x450
[<ffffffff8103e413>] worker_thread+0x123/0x2d0
Signed-off-by: Anton Vorontsov <anton.vorontsov@linaro.org>
Acked-by: KAMEZAWA Hiroyuki <kamezawa.hiroyu@jp.fujitsu.com>
Cc: Kirill A. Shutemov <kirill@shutemov.name>
Cc: Michal Hocko <mhocko@suse.cz>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 880641bb9da2473e9ecf6c708d993b29928c1b3c upstream.
Bart Van Assche reported a hung fio process when either hot-removing
storage or when interrupting the fio process itself. The (pruned) call
trace for the latter looks like so:
fio D 0000000000000001 0 6849 6848 0x00000004
ffff880092541b88 0000000000000046 ffff880000000000 ffff88012fa11dc0
ffff88012404be70 ffff880092541fd8 ffff880092541fd8 ffff880092541fd8
ffff880128b894d0 ffff88012404be70 ffff880092541b88 000000018106f24d
Call Trace:
schedule+0x3f/0x60
io_schedule+0x8f/0xd0
wait_for_all_aios+0xc0/0x100
exit_aio+0x55/0xc0
mmput+0x2d/0x110
exit_mm+0x10d/0x130
do_exit+0x671/0x860
do_group_exit+0x44/0xb0
get_signal_to_deliver+0x218/0x5a0
do_signal+0x65/0x700
do_notify_resume+0x65/0x80
int_signal+0x12/0x17
The problem lies with the allocation batching code. It will
opportunistically allocate kiocbs, and then trim back the list of iocbs
when there is not enough room in the completion ring to hold all of the
events.
In the case above, what happens is that the pruning back of events ends
up freeing up the last active request and the context is marked as dead,
so it is thus responsible for waking up waiters. Unfortunately, the
code does not check for this condition, so we end up with a hung task.
Signed-off-by: Jeff Moyer <jmoyer@redhat.com>
Reported-by: Bart Van Assche <bvanassche@acm.org>
Tested-by: Bart Van Assche <bvanassche@acm.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 5b6b0ad6e572b32a641116aaa5f897ffebe31e44 upstream.
On i.MX53 we have to write a special SDHCI_CMD_ABORTCMD to the
SDHCI_TRANSFER_MODE register during a MMC_STOP_TRANSMISSION
command. This works for SD cards. However, with MMC cards
the MMC_SET_BLOCK_COUNT command is used instead, but this
needs the same handling. Fix MMC cards by testing for the
MMC_SET_BLOCK_COUNT command aswell. Tested on a custom i.MX53
board with a Transcend MMC+ card and eMMC.
The kernel started used MMC_SET_BLOCK_COUNT in 3.0, so this
is a regression for these boards introduced in 3.0; it should
go to 3.0/3.1/3.2-stable.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Acked-by: Shawn Guo <shawn.guo@linaro.org>
Signed-off-by: Chris Ball <cjb@laptop.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit ef8781989a1bcd05aa47e853917c37df44917194 upstream.
Some callbacks are set too early -- i.e. we can have dma capabilities but
we can't get a dma channel. So wait to get the dma channel before setting
callbacks and change logs consequently.
Signed-off-by: Ludovic Desroches <ludovic.desroches@atmel.com>
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 62aca403657fe30e5235c5331e9871e676d9ea0a upstream.
Michael Cree said:
: : I have noticed some user space problems (pulseaudio crashes in pthread
: : code, glibc/nptl test suite failures, java compiler freezes on SMP alpha
: : systems) that arise when using a 2.6.39 or later kernel on Alpha.
: : Bisecting between 2.6.38 and 2.6.39 (using glibc/nptl test suite as
: : criterion for good/bad kernel) eventually leads to:
: :
: : 8d7718aa082aaf30a0b4989e1f04858952f941bc is the first bad commit
: : commit 8d7718aa082aaf30a0b4989e1f04858952f941bc
: : Author: Michel Lespinasse <walken@google.com>
: : Date: Thu Mar 10 18:50:58 2011 -0800
: :
: : futex: Sanitize futex ops argument types
: :
: : Change futex_atomic_op_inuser and futex_atomic_cmpxchg_inatomic
: : prototypes to use u32 types for the futex as this is the data type the
: : futex core code uses all over the place.
: :
: : Looking at the commit I see there is a change of the uaddr argument in
: : the Alpha architecture specific code for futexes from int to u32, but I
: : don't see why this should cause a problem.
Richard Henderson said:
: futex_atomic_cmpxchg_inatomic(u32 *uval, u32 __user *uaddr,
: u32 oldval, u32 newval)
: ...
: : "r"(uaddr), "r"((long)oldval), "r"(newval)
:
:
: There is no 32-bit compare instruction. These are implemented by
: consistently extending the values to a 64-bit type. Since the
: load instruction sign-extends, we want to sign-extend the other
: quantity as well (despite the fact it's logically unsigned).
:
: So:
:
: - : "r"(uaddr), "r"((long)oldval), "r"(newval)
: + : "r"(uaddr), "r"((long)(int)oldval), "r"(newval)
:
: should do the trick.
Michael said:
: This fixes the glibc test suite failures and the pulseaudio related
: crashes, but it does not fix the java compiiler lockups that I was (and
: are still) observing. That is some other problem.
Reported-by: Michael Cree <mcree@orcon.net.nz>
Tested-by: Michael Cree <mcree@orcon.net.nz>
Acked-by: Phil Carmody <ext-phil.2.carmody@nokia.com>
Cc: Richard Henderson <rth@twiddle.net>
Cc: Michel Lespinasse <walken@google.com>
Cc: Ivan Kokshaysky <ink@jurassic.park.msu.ru>
Reviewed-by: Matt Turner <mattst88@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit ee932bf9acb2e2c6a309e808000f24856330e3f9 upstream.
In the current kernel implementation, the Logitech Harmony 900 remote
control is matched to the cdc_ether driver through the generic
USB_CDC_SUBCLASS_MDLM entry. However, this device appears to be of the
pseudo-MDLM (Belcarra) type, rather than the standard one. This patch
blacklists the Harmony 900 from the cdc_ether driver and whitelists it for
the pseudo-MDLM driver in zaurus.
Signed-off-by: Scott Talbert <talbert@techie.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit e39d40c65dfd8390b50c03482ae9e289b8a8f351 upstream.
s3c2410_dma_suspend suspends channels from 0 to dma_channels.
s3c2410_dma_resume resumes channels in reverse order. So
pointer should be decremented instead of being incremented.
Signed-off-by: Gusakov Andrey <dron0gus@gmail.com>
Reviewed-by: Heiko Stuebner <heiko@sntech.de>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 52abb700e16a9aa4cbc03f3d7f80206cbbc80680 upstream.
Xommit ac5637611(genirq: Unmask oneshot irqs when thread was not woken)
fails to unmask when a !IRQ_ONESHOT threaded handler is handled by
handle_level_irq.
This happens because thread_mask is or'ed unconditionally in
irq_wake_thread(), but for !IRQ_ONESHOT interrupts never cleared. So
the check for !desc->thread_active fails and keeps the interrupt
disabled.
Keep the thread_mask zero for !IRQ_ONESHOT interrupts.
Document the thread_mask magic while at it.
Reported-and-tested-by: Sven Joachim <svenjoac@gmx.de>
Reported-and-tested-by: Stefan Lippers-Hollmann <s.l-h@gmx.de>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit e7c248a049c2aac21bded0b0722caee6f0e57256 upstream.
The jack detection on WM1811 is often required during system suspend, add
it as another check when deciding if we should suspend.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 81b5482c32769abb6dfb979560dab2f952ba86fa upstream.
The code is currently always checking the first resource of every
device only (several times.) This has been broken since the ACPI check
was added in February 2010 in commit
91fedede0338eb6203cdd618d8ece873fdb7c22c.
Fix the check to run on each resource individually, once.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 5189fa19a4b2b4c3bec37c3a019d446148827717 upstream.
There is only one error code to return for a bad user-space buffer
pointer passed to a system call in the same address space as the
system call is executed, and that is EFAULT. Furthermore, the
low-level access routines, which catch most of the faults, return
EFAULT already.
Signed-off-by: H. Peter Anvin <hpa@zytor.com>
Reviewed-by: Oleg Nesterov <oleg@redhat.com>
Acked-by: Roland McGrath <roland@hack.frob.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit c8e252586f8d5de906385d8cf6385fee289a825e upstream.
The regset common infrastructure assumed that regsets would always
have .get and .set methods, but not necessarily .active methods.
Unfortunately people have since written regsets without .set methods.
Rather than putting in stub functions everywhere, handle regsets with
null .get or .set methods explicitly.
Signed-off-by: H. Peter Anvin <hpa@zytor.com>
Reviewed-by: Oleg Nesterov <oleg@redhat.com>
Acked-by: Roland McGrath <roland@hack.frob.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 7bff172a352a2fbe9856bba517d71a2072aab041 upstream.
A bug report with an old Sony laptop showed that we can't rely on BIOS
setting the pins of headphones but the driver should set always by
itself.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
