| Age | Commit message (Collapse) | Author |
|---|
|
Vendor ID 0x10de0071 is used by a yet-to-be-named GPU chip.
Signed-off-by: Aaron Plattner <aplattner@nvidia.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
|
|
When we plug a 3-ring headset on the Dell machines (VID: 0x10ec0255,
SID: 0x1028065c; VID: 0x10ec0255, SID: 0x10280680; VID: 0x10ec0292,
SID: 0x10280684), the headset mic can't be detected, after apply this
patch, the headset mic can work well.
And on the machine with SID 0x10280684, and the Lineout and external
microphone should be routed to docking, this patch also fix this
problem.
BugLink: https://bugs.launchpad.net/bugs/1297581
Cc: David Henningsson <david.henningsson@canonical.com>
Cc: stable@vger.kernel.org
Signed-off-by: Hui Wang <hui.wang@canonical.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
|
|
Since commit 1df5a06a ("ALSA: hda - hdmi: Fix programmed active channel
count") channel count is no longer being set if monitor_present is 0.
This is because setting the count was moved after the CA value is
determined, which is only after the monitor_present check in
hdmi_setup_audio_infoframe().
Unfortunately, in some cases, such as with a non-spec-compliant codec or
with a problematic video driver, monitor_present is always 0. As a
specific example, this seems to happen with gen1 ATV (SiI1390 codec),
causing left-channel-only stereo playback (multi-channel playback has
apparently never worked with this codec despite it reporting 8 channels,
reason unknown).
Simply setting converter channel count without setting the pin infoframe
and channel mapping as well does not theoretically make much sense as
this will just mean they are out-of-sync and multichannel playback will
have a wrong channel mapping.
However, adding back just setting the converter channel count even in
no-monitor case is the safest change which at least fixes the stereo
playback regression on SiI1390 codec. Do that.
Signed-off-by: Anssi Hannula <anssi.hannula@iki.fi>
Reported-by: Stephan Raue <stephan@openelec.tv>
Tested-by: Stephan Raue <stephan@openelec.tv>
Cc: <stable@vger.kernel.org> # 3.12+
Signed-off-by: Takashi Iwai <tiwai@suse.de>
|
|
The TEAC UD-H01 firmware sends wrong feedback frequency values, thus
causing the PC to send the samples at a wrong rate, which results in
clicks and crackles in the output.
Add a workaround to detect and fix the corruption.
Signed-off-by: Clemens Ladisch <clemens@ladisch.de>
[mick37@gmx.de: use sender->udh01_fb_quirk rather than
ep->udh01_fb_quirk in snd_usb_handle_sync_urb()]
Reported-and-tested-by: Mick <mick37@gmx.de>
Reported-and-tested-by: Andrea Messa <andr.messa@tiscali.it>
Cc: <stable@vger.kernel.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
|
|
The recent addition of the USB audio mixer suspend/resume may lead to
deadlocks when the driver tries to call usb_autopm_get_interface()
recursively, since the function tries to sync with the finish of the
other calls. For avoiding it, introduce a flag indicating the resume
operation and avoids the recursive usb_autopm_get_interface() calls
during the resume.
Reported-and-tested-by: Bryan Quigley <gquigs@gmail.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
|
|
The suspend callback of usb-audio driver may be called multiple times
per suspend when multiple USB interfaces are bound to a single sound
card instance. In such a case, it's superfluous to save the mixer
values multiple times. This patch fixes it by checking the counter.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
|
|
DEBUG not defined
This (widely used) construction:
if(printk_ratelimit())
dev_dbg()
Causes the ratelimiting to spam the kernel log with the "callbacks suppressed"
message below, even while the dev_dbg it is supposed to rate limit wouldn't
print anything because DEBUG is not defined for this device.
[ 533.803964] retire_playback_urb: 852 callbacks suppressed
[ 538.807930] retire_playback_urb: 852 callbacks suppressed
[ 543.811897] retire_playback_urb: 852 callbacks suppressed
[ 548.815745] retire_playback_urb: 852 callbacks suppressed
[ 553.819826] retire_playback_urb: 852 callbacks suppressed
So use dev_dbg_ratelimited() instead of this construction.
Signed-off-by: Sander Eikelenboom <linux@eikelenboom.it>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
|
|
When we plug a 3-ring headset on the Dell machine (VID: 0x10ec0255,
SID: 0x1028067e), the headset mic can't be detected, after apply this
patch, the headset mic can work well.
BugLink: https://bugs.launchpad.net/bugs/1297581
Cc: David Henningsson <david.henningsson@canonical.com>
Cc: stable@vger.kernel.org
Signed-off-by: Hui Wang <hui.wang@canonical.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
|
|
The recent commit (ca460f86521) changed the CORB RP reset procedure to
follow the specification with a couple of sanity checks.
Unfortunately, Nvidia controller chips seem not following this way,
and spew the warning messages like:
snd_hda_intel 0000:00:10.1: CORB reset timeout#1, CORBRP = 0
This patch adds the workaround for such chips. It just skips the new
reset procedure for the known broken chips.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
|
|
When we plug a 3-ring headset on the Dell machine (VID: 0x10ec0255,
SID: 0x10280674), the headset mic can't be detected, after apply this
patch, the headset mic can work well.
BugLink: https://bugs.launchpad.net/bugs/1297581
Cc: David Henningsson <david.henningsson@canonical.com>
Cc: stable@vger.kernel.org
Signed-off-by: Hui Wang <hui.wang@canonical.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/broonie/sound into for-linus
ASoC: Fixes for v3.15
A smattering of driver-specific fixes here, nothing generic. The Cirrus
CODEC conversions to devm_ are leak fixes - the conversion adds missing
error handling code.
|
|
'asoc/fix/rcar', 'asoc/fix/tlv320aic31xx' and 'asoc/fix/tlv320aic3x' into asoc-linus
|
|
'asoc/fix/cs42l73' and 'asoc/fix/fsl-spdif' into asoc-linus
|
|
|
|
Commit 0406a40a0 ("ASoC: jz4740: Use the generic dmaengine PCM driver")
jz4740-pcm.c file, but neglected to remove the Makefile entries.
Fixes: 0406a40a0 ("ASoC: jz4740: Use the generic dmaengine PCM driver")
Reported-by: kbuild test robot <fengguang.wu@intel.com>
Reported-by: Ralf Baechle <ralf@linux-mips.org>
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Mark Brown <broonie@linaro.org>
|
|
There were occasional ADSP crash during reboot testing:
[ 11.883364] BUG: unable to handle kernel paging request at ffffc90121700000
[ 11.883380] IP: [<ffffffffc024d8bc>] sst_module_insert_fixed_block+0x24f/0x26d [snd_soc_sst_dsp]
[ 11.883397] PGD 7800b067 PUD 0
[ 11.883405] Oops: 0002 [#1] SMP
[ 11.886418] gsmi: Log Shutdown Reason 0x03
The virtual address, ffffc90121700000, was out of range. The virtual
address is calculated by adding LPE base address with an offset:
sst_memcpy32(dsp->addr.lpe + data->offset, data->data, data->size);
The offset is calculated in sst_byt_parse_module, by subtraction of
two virtual addresses dsp->addr.fw_ext and dsp->addr.lpe:
block_data.offset = block->ram_offset + (dsp->addr.fw_ext - dsp->addr.lpe);
These virtual addresses are assigned by kernel from ioremap:
sst->addr.lpe = ioremap(pdata->lpe_base, pdata->lpe_size);
sst->addr.fw_ext = ioremap(pdata->fw_base, pdata->fw_size);
In current driver code, offset is defined as unsigned int32:
struct sst_module_data {
...
u32 offset; /* offset in FW file */
};
Most of the time kernel assigned virtual addresses with addr.fw_ext
greater than addr.lpe. But sometimes it was the other way round.
Fix the problem by declaring offset as signed int32_t.
Signed-off-by: Wenkai Du <wenkai.du@intel.com>
Signed-off-by: Jarkko Nikula <jarkko.nikula@linux.intel.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
|
|
Commit 9e1fda4ae158 ("ASoC: dapm: Implement mixer input auto-disable")
is trying to free the widget it allocated by snd_soc_dapm_new_control()
call in dapm_kcontrol_data_alloc() by adding kfree(data->widget) to
dapm_kcontrol_free().
This is causing a widget double free with auto-disabled DAPM kcontrols
in sound card unregistration because widgets are already freed before
dapm_kcontrol_free() is called.
Reason for that is all widgets are added into dapm->card->widgets list
in snd_soc_dapm_new_control() and freed in dapm_free_widgets() during
execution of snd_soc_dapm_free().
Now snd_soc_dapm_free() calls for different DAPM contexts happens before
snd_card_free() call from where the call chain to dapm_kcontrol_free()
begins:
soc_cleanup_card_resources()
soc_remove_dai_links()
soc_remove_link_dais()
snd_soc_dapm_free(&cpu_dai->dapm)
soc_remove_link_components()
soc_remove_platform()
snd_soc_dapm_free(&platform->dapm)
soc_remove_codec()
snd_soc_dapm_free(&codec->dapm)
snd_soc_dapm_free(&card->dapm)
snd_card_free()
snd_card_do_free()
snd_device_free_all()
snd_device_free()
snd_ctl_dev_free()
snd_ctl_remove()
snd_ctl_free_one()
dapm_kcontrol_free()
This wasn't making harm with ordinary DAPM kcontrols since data->widget is NULL for
them.
Fixes: 9e1fda4ae158 (ASoC: dapm: Implement mixer input auto-disable)
Signed-off-by: Jarkko Nikula <jarkko.nikula@linux.intel.com>
Acked-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Mark Brown <broonie@linaro.org>
Cc: stable@vger.kernel.org
|
|
|
|
Pull slave-dmaengine fixes from Vinod Koul:
"Back from long weekend here in India and now the time to send fixes
for slave dmaengine.
- Dan's fix of sirf xlate code
- Jean's fix for timberland
- edma fixes by Sekhar for SG handling and Yuan for changing init
call"
* 'fixes' of git://git.infradead.org/users/vkoul/slave-dma:
dma: fix eDMA driver as a subsys_initcall
dmaengine: sirf: off by one in of_dma_sirfsoc_xlate()
platform: Fix timberdale dependencies
dma: edma: fix incorrect SG list handling
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/joro/iommu
Pull iommu fixes from Joerg Roedel:
"Fixes for regressions:
- fix wrong IOMMU enumeration causing some SCSI device drivers
initialization failures
- ARM-SMMU fixes for a panic condition and a wrong return value"
* tag 'iommu-fixes-v3.15-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/joro/iommu:
iommu/arm-smmu: fix panic in arm_smmu_alloc_init_pte
iommu/arm-smmu: Return 0 on unmap failure
iommu/vt-d: fix bug in matching PCI devices with DRHD/RMRR descriptors
iommu/vt-d: Fix get_domain_for_dev() handling of upstream PCIe bridges
iommu/vt-d: fix memory leakage caused by commit ea8ea46
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull perf tooling fixes from Ingo Molnar:
"Three small tooling fixes"
* 'perf-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
perf tools: Improve error reporting
perf tools: Adjust symbols in VDSO
perf kvm: Fix 'Min time' counting in report command
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/jolsa/perf into perf/urgent
Pull perf/urgent fixes from Jiri Olsa:
User visible changes:
* Adjust symbols in VDSO to properly resolve its function names (Vladimir Nikulichev)
* Improve error reporting for record session failure (Adrien BAK)
* Fix 'Min time' counting in report command (Alexander Yarygin)
Signed-off-by: Jiri Olsa <jolsa@redhat.com>
Signed-off-by: Ingo Molnar <mingo@kernel.org>
|
|
In the current version, when using perf record, if something goes
wrong in tools/perf/builtin-record.c:375
session = perf_session__new(file, false, NULL);
The error message:
"Not enough memory for reading per file header"
is issued. This error message seems to be outdated and is not very
helpful. This patch proposes to replace this error message by
"Perf session creation failed"
I believe this issue has been brought to lkml:
https://lkml.org/lkml/2014/2/24/458
although this patch only tackles a (small) part of the issue.
Additionnaly, this patch improves error reporting in
tools/perf/util/data.c open_file_write.
Currently, if the call to open fails, the user is unaware of it.
This patch logs the error, before returning the error code to
the caller.
Reported-by: Will Deacon <will.deacon@arm.com>
Signed-off-by: Adrien BAK <adrien.bak@metascale.org>
Link: http://lkml.kernel.org/r/1397786443.3093.4.camel@beast
[ Reorganize the changelog into paragraphs ]
[ Added empty line after fd declaration in open_file_write ]
Signed-off-by: Jiri Olsa <jolsa@redhat.com>
|
|
pert-report doesn't resolve function names in VDSO:
$ perf report --stdio -g flat,0.0,15,callee --sort pid
...
8.76%
0x7fff6b1fe861
__gettimeofday
ACE_OS::gettimeofday()
...
In this case symbol values should be adjusted the same way as for executables,
relocatable objects and prelinked libraries.
After fix:
$ perf report --stdio -g flat,0.0,15,callee --sort pid
...
8.76%
__vdso_gettimeofday
__gettimeofday
ACE_OS::gettimeofday()
Signed-off-by: Vladimir Nikulichev <nvs@tbricks.com>
Tested-by: Namhyung Kim <namhyung@kernel.org>
Reviewed-by: Adrian Hunter <adrian.hunter@intel.com>
Link: http://lkml.kernel.org/r/969812.163009436-sendEmail@nvs
Signed-off-by: Jiri Olsa <jolsa@redhat.com>
|
|
Every event in the perf-kvm has a 'stats' structure, which contains
max/min/average/etc times of handling this event.
The problem is that the 'perf-kvm stat report' command always shows
that 'min time' is 0us for every event. Example:
# perf kvm stat report
Analyze events for all VCPUs:
VM-EXIT Samples Samples% Time% Min Time Max Time Avg time
[..]
0xB2 MSCH 12 0.07% 0.00% 0us 8us 7.31us ( +- 2.11% )
0xB2 CHSC 12 0.07% 0.00% 0us 18us 9.39us ( +- 9.49% )
0xB2 STPX 8 0.05% 0.00% 0us 2us 1.88us ( +- 7.18% )
0xB2 STSI 7 0.04% 0.00% 0us 44us 16.49us ( +- 38.20% )
[..]
This happens because the 'stats' structure is not initialized and
stats->min equals to 0. Lets initialize the structure for every
event after its allocation using init_stats() function. This initializes
stats->min to -1 and makes 'Min time' statistics counting work:
# perf kvm stat report
Analyze events for all VCPUs:
VM-EXIT Samples Samples% Time% Min Time Max Time Avg time
[..]
0xB2 MSCH 12 0.07% 0.00% 6us 8us 7.31us ( +- 2.11% )
0xB2 CHSC 12 0.07% 0.00% 7us 18us 9.39us ( +- 9.49% )
0xB2 STPX 8 0.05% 0.00% 1us 2us 1.88us ( +- 7.18% )
0xB2 STSI 7 0.04% 0.00% 1us 44us 16.49us ( +- 38.20% )
[..]
Signed-off-by: Alexander Yarygin <yarygin@linux.vnet.ibm.com>
Signed-off-by: Christian Borntraeger <borntraeger@de.ibm.com>
Reviewed-by: David Ahern <dsahern@gmail.com>
Link: http://lkml.kernel.org/r/1397053319-2130-3-git-send-email-borntraeger@de.ibm.com
[ Fixing the perf examples changelog output ]
Signed-off-by: Jiri Olsa <jolsa@redhat.com>
|
|
A va_list needs to be copied in case it needs to be used twice.
Thanks to Hugh for debugging this issue, leading to various panics.
Tested:
lpq84:~# echo "|/foobar12345 %h %h %h %h %h %h %h %h %h %h %h %h %h %h %h %h %h %h %h %h" >/proc/sys/kernel/core_pattern
'produce_core' is simply : main() { *(int *)0 = 1;}
lpq84:~# ./produce_core
Segmentation fault (core dumped)
lpq84:~# dmesg | tail -1
[ 614.352947] Core dump to |/foobar12345 lpq84 lpq84 lpq84 lpq84 lpq84 lpq84 lpq84 lpq84 lpq84 lpq84 lpq84 lpq84 lpq84 lpq84 lpq84 lpq84 lpq84 lpq84 lpq84 (null) pipe failed
Notice the last argument was replaced by a NULL (we were lucky enough to
not crash, but do not try this on your production machine !)
After fix :
lpq83:~# echo "|/foobar12345 %h %h %h %h %h %h %h %h %h %h %h %h %h %h %h %h %h %h %h %h" >/proc/sys/kernel/core_pattern
lpq83:~# ./produce_core
Segmentation fault
lpq83:~# dmesg | tail -1
[ 740.800441] Core dump to |/foobar12345 lpq83 lpq83 lpq83 lpq83 lpq83 lpq83 lpq83 lpq83 lpq83 lpq83 lpq83 lpq83 lpq83 lpq83 lpq83 lpq83 lpq83 lpq83 lpq83 lpq83 pipe failed
Fixes: 5fe9d8ca21cc ("coredump: cn_vprintf() has no reason to call vsnprintf() twice")
Signed-off-by: Eric Dumazet <edumazet@google.com>
Diagnosed-by: Hugh Dickins <hughd@google.com>
Acked-by: Oleg Nesterov <oleg@redhat.com>
Cc: Neil Horman <nhorman@tuxdriver.com>
Cc: Andrew Morton <akpm@linux-foundation.org>
Cc: stable@vger.kernel.org # 3.11+
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull x86 fix from Ingo Molnar:
"This fixes the preemption-count imbalance crash reported by Owen
Kibel"
* 'x86-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
x86/mce: Fix CMCI preemption bugs
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull scheduler fixes from Ingo Molnar:
"Two fixes:
- a SCHED_DEADLINE task selection fix
- a sched/numa related lockdep splat fix"
* 'sched-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
sched: Check for stop task appearance when balancing happens
sched/numa: Fix task_numa_free() lockdep splat
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull perf fixes from Ingo Molnar:
"Two kernel side fixes:
- an Intel uncore PMU driver potential crash fix
- a kprobes/perf-call-graph interaction fix"
* 'perf-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
perf/x86/intel: Use rdmsrl_safe() when initializing RAPL PMU
kprobes/x86: Fix page-fault handling logic
|
|
Pull drm fixes from Dave Airlie:
"Unfortunately this contains no easter eggs, its a bit larger than I'd
like, but I included a patch that just moves code from one file to
another and I'd like to avoid merge conflicts with that later, so it
makes it seem worse than it is,
Otherwise:
- radeon: fixes to use new microcode to stabilise some cards, use
some common displayport code, some runtime pm fixes, pll regression
fixes
- i915: fix for some context oopses, a warn in a used path, backlight
fixes
- nouveau: regression fix
- omap: a bunch of fixes"
* 'drm-fixes' of git://people.freedesktop.org/~airlied/linux: (51 commits)
drm: bochs: drop unused struct fields
drm: bochs: add power management support
drm: cirrus: add power management support
drm: Split out drm_probe_helper.c from drm_crtc_helper.c
drm/plane-helper: Don't fake-implement primary plane disabling
drm/ast: fix value check in cbr_scan2
drm/nouveau/bios: fix a bit shift error introduced by 457e77b
drm/radeon/ci: make sure mc ucode is loaded before checking the size
drm/radeon/si: make sure mc ucode is loaded before checking the size
drm/radeon: improve PLL params if we don't match exactly v2
drm/radeon: memory leak on bo reservation failure. v2
drm/radeon: fix VCE fence command
drm/radeon: re-enable mclk dpm on R7 260X asics
drm/radeon: add support for newer mc ucode on CI (v2)
drm/radeon: add support for newer mc ucode on SI (v2)
drm/radeon: apply more strict limits for PLL params v2
drm/radeon: update CI DPM powertune settings
drm/radeon: fix runpm handling on APUs (v4)
drm/radeon: disable mclk dpm on R7 260X
drm/tegra: Remove gratuitous pad field
...
|
|
git://people.freedesktop.org/~deathsimple/linux into drm-next
Some i2c fixes over DisplayPort.
* 'drm-next-3.15-wip' of git://people.freedesktop.org/~deathsimple/linux:
drm/radeon: Improve vramlimit module param documentation
drm/radeon: fix audio pin counts for DCE6+ (v2)
drm/radeon/dp: switch to the common i2c over aux code
drm/dp/i2c: Update comments about common i2c over dp assumptions (v3)
drm/dp/i2c: send bare addresses to properly reset i2c connections (v4)
drm/radeon/dp: handle zero sized i2c over aux transactions (v2)
drm/i915: support address only i2c-over-aux transactions
drm/tegra: dp: Support address-only I2C-over-AUX transactions
|
|
Pull more networking fixes from David Miller:
1) Fix mlx4_en_netpoll implementation, it needs to schedule a NAPI
context, not synchronize it. From Chris Mason.
2) Ipv4 flow input interface should never be zero, it should be
LOOPBACK_IFINDEX instead. From Cong Wang and Julian Anastasov.
3) Properly configure MAC to PHY connection in mvneta devices, from
Thomas Petazzoni.
4) sys_recv should use SYSCALL_DEFINE. From Jan Glauber.
5) Tunnel driver ioctls do not use the correct namespace, fix from
Nicolas Dichtel.
6) Fix memory leak on seccomp filter attach, from Kees Cook.
7) Fix lockdep warning for nested vlans, from Ding Tianhong.
8) Crashes can happen in SCTP due to how the auth_enable value is
managed, fix from Vlad Yasevich.
9) Wireless fixes from John W Linville and co.
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net: (45 commits)
net: sctp: cache auth_enable per endpoint
tg3: update rx_jumbo_pending ring param only when jumbo frames are enabled
vlan: Fix lockdep warning when vlan dev handle notification
seccomp: fix memory leak on filter attach
isdn: icn: buffer overflow in icn_command()
ip6_tunnel: use the right netns in ioctl handler
sit: use the right netns in ioctl handler
ip_tunnel: use the right netns in ioctl handler
net: use SYSCALL_DEFINEx for sys_recv
net: mdio-gpio: Add support for separate MDI and MDO gpio pins
net: mdio-gpio: Add support for active low gpio pins
net: mdio-gpio: Use devm_ functions where possible
ipv4, route: pass 0 instead of LOOPBACK_IFINDEX to fib_validate_source()
ipv4, fib: pass LOOPBACK_IFINDEX instead of 0 to flowi4_iif
mlx4_en: don't use napi_synchronize inside mlx4_en_netpoll
net: mvneta: properly configure the MAC <-> PHY connection in all situations
net: phy: add minimal support for QSGMII PHY
sfc:On MCDI timeout, issue an FLR (and mark MCDI to fail-fast)
mwifiex: fix hung task on command timeout
mwifiex: process event before command response
...
|
|
Pull cifs fixes from Steve French:
"A set of 5 small cifs fixes"
* 'for-next' of git://git.samba.org/sfrench/cifs-2.6:
cif: fix dead code
cifs: fix error handling cifs_user_readv
fs: cifs: remove unused variable.
Return correct error on query of xattr on file with empty xattrs
cifs: Wait for writebacks to complete before attempting write.
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/char-misc
Pull char/misc driver fixes from Greg KH:
"Here are a few driver fixes for char/misc drivers that resolve
reported issues.
All have been in linux-next successfully for a few days"
* tag 'char-misc-3.15-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/char-misc:
Drivers: hv: vmbus: Negotiate version 3.0 when running on ws2012r2 hosts
Tools: hv: Handle the case when the target file exists correctly
vme_tsi148: Utilize to_pci_dev() macro
vme_tsi148: Fix PCI address mapping assumption
vme_tsi148: Fix typo in tsi148_slave_get()
w1: avoid recursive device_add
w1: fix netlink refcnt leak on error path
misc: Grammar s/addition/additional/
drivers: mcb: fix memory leak in chameleon_parse_cells() error path
mei: ignore client writing state during cb completion
mei: me: do not load the driver if the FW doesn't support MEI interface
GenWQE: Increase driver version number
GenWQE: Fix multithreading problems
GenWQE: Ensure rc is not returning an uninitialized value
GenWQE: Add wmb before DDCB is started
GenWQE: Enable access to VPD flash area
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core
Pull driver core fixes from Greg KH:
"Here are some driver core fixes for 3.15-rc2. Also in here are some
documentation updates, as well as an API removal that had to wait for
after -rc1 due to the cleanups coming into you from multiple developer
trees (this one and the PPC tree.)
All have been in linux next successfully"
* tag 'driver-core-3.15-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core:
drivers/base/dd.c incorrect pr_debug() parameters
Documentation: Update stable address in Chinese and Japanese translations
topology: Fix compilation warning when not in SMP
Chinese: add translation of io_ordering.txt
stable_kernel_rules: spelling/word usage
sysfs, driver-core: remove unused {sysfs|device}_schedule_callback_owner()
kernfs: protect lazy kernfs_iattrs allocation with mutex
fs: Don't return 0 from get_anon_bdev
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/staging
Pull staging driver fixes from Greg KH:
"Here are a few staging driver fixes for issues that have been reported
for 3.15-rc2.
Also dominating the diffstat for the pull request is the removal of
the rtl8187se driver. It's no longer needed in staging as a "real"
driver for this hardware is now merged in the tree in the "correct"
location in drivers/net/
All of these patches have been tested in linux-next"
* tag 'staging-3.15-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/staging:
staging: r8188eu: Fix case where ethtype was never obtained and always be checked against 0
staging: r8712u: Fix case where ethtype was never obtained and always be checked against 0
staging: r8188eu: Calling rtw_get_stainfo() with a NULL sta_addr will return NULL
staging: comedi: fix circular locking dependency in comedi_mmap()
staging: r8723au: Add missing initialization of change_inx in sort algorithm
Staging: unisys: use after free in list_for_each()
staging: unisys: use after free in error messages
staging: speakup: fix misuse of kstrtol() in handle_goto()
staging: goldfish: Call free_irq in error path
staging: delete rtl8187se wireless driver
staging: rtl8723au: Fix buffer overflow in rtw_get_wfd_ie()
staging: gs_fpgaboot: remove __TIMESTAMP__ macro
staging: vme: fix memory leak in vme_user_probe()
staging: fpgaboot: clean up Makefile
staging/usbip: fix store_attach() sscanf return value check
staging/usbip: userspace - fix usbipd SIGSEGV from refresh_exported_devices()
staging: rtl8188eu: remove spaces, correct counts to unbreak P2P ioctls
staging/rtl8821ae: Fix OOM handling in _rtl_init_deferred_work()
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty
Pull tty/serial driver fixes from Greg KH:
"Here are a number of small tty/serial driver fixes for 3.15-rc2. Also
in here are some Documentation file removals for drivers that we
removed a long time ago, no need to keep it around any longer.
All of these have been in linux-next for a bit"
* tag 'tty-3.15-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty:
Revert "serial: 8250, disable "too much work" messages"
serial: amba-pl011: fix regression, causing an Oops on rmmod
tty: Fix help text of SYNCLINK_CS
tty: fix memleak in alloc_pid
ttyprintk: Allow built as a module
ttyprintk: Fix wrong tty_unregister_driver() call in the error path
serial: 8250, disable "too much work" messages
Documentation/serial: Delete obsolete driver documentation
serial: omap: Fix missing pm_runtime_resume handling by simplifying code
serial_core: Fix pm imbalance on unbind
serial: pl011: change Rx burst size to half of trigger level
serial: timberdale: Depend on X86_32
serial: st-asc: Fix SysRq char handling
Revert "serial: clps711x: Give a chance to perform useful tasks during wait loop"
serial_core: Fix conditional start_tx on ring buffer not empty
serial: efm32: use $vendor,$device scheme for compatible string
serial: omap: free the wakeup settings in remove
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb
Pull USB fixes from Greg KH:
"Here are a number of tiny USB fixes and new device ids for 3.15-rc2.
Nothing major, just issues some people have reported.
All of these have been in linux-next"
* tag 'usb-3.15-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb:
uas: fix deadlocky memory allocations
uas: fix error handling during scsi_scan()
uas: fix GFP_NOIO under spinlock
uwb: adds missing error handling
USB: cdc-acm: Remove Motorola/Telit H24 serial interfaces from ACM driver
USB: ohci-jz4740: FEAT_POWER is a port feature, not a hub feature
USB: ohci-jz4740: Fix uninitialized variable warning
USB: EHCI: tegra: set txfill_tuning
usb: ehci-platform: Return immediately from suspend if ehci_suspend fails
usb: ehci-exynos: Return immediately from suspend if ehci_suspend fails
USB: fix crash during hotplug of PCI USB controller card
USB: cdc-acm: fix double usb_autopm_put_interface() in acm_port_activate()
usb: usb-common: fix typo for usb_state_string
USB: usb_wwan: fix handling of missing bulk endpoints
USB: pl2303: add ids for Hewlett-Packard HP POS pole displays
USB: cp210x: Add 8281 (Nanotec Plug & Drive)
usb: option driver, add support for Telit UE910v2
Revert "USB: serial: add usbid for dell wwan card to sierra.c"
USB: serial: ftdi_sio: add id for Brainboxes serial cards
|
|
Merge misc fixes from Andrew Morton:
"13 fixes"
* emailed patches from Andrew Morton <akpm@linux-foundation.org>:
thp: close race between split and zap huge pages
mm: fix new kernel-doc warning in filemap.c
mm: fix CONFIG_DEBUG_VM_RB description
mm: use paravirt friendly ops for NUMA hinting ptes
mips: export flush_icache_range
mm/hugetlb.c: add cond_resched_lock() in return_unused_surplus_pages()
wait: explain the shadowing and type inconsistencies
Shiraz has moved
Documentation/vm/numa_memory_policy.txt: fix wrong document in numa_memory_policy.txt
powerpc/mm: fix ".__node_distance" undefined
kernel/watchdog.c:touch_softlockup_watchdog(): use raw_cpu_write()
init/Kconfig: move the trusted keyring config option to general setup
vmscan: reclaim_clean_pages_from_list() must use mod_zone_page_state()
|
|
Sasha Levin has reported two THP BUGs[1][2]. I believe both of them
have the same root cause. Let's look to them one by one.
The first bug[1] is "kernel BUG at mm/huge_memory.c:1829!". It's
BUG_ON(mapcount != page_mapcount(page)) in __split_huge_page(). From my
testing I see that page_mapcount() is higher than mapcount here.
I think it happens due to race between zap_huge_pmd() and
page_check_address_pmd(). page_check_address_pmd() misses PMD which is
under zap:
CPU0 CPU1
zap_huge_pmd()
pmdp_get_and_clear()
__split_huge_page()
anon_vma_interval_tree_foreach()
__split_huge_page_splitting()
page_check_address_pmd()
mm_find_pmd()
/*
* We check if PMD present without taking ptl: no
* serialization against zap_huge_pmd(). We miss this PMD,
* it's not accounted to 'mapcount' in __split_huge_page().
*/
pmd_present(pmd) == 0
BUG_ON(mapcount != page_mapcount(page)) // CRASH!!!
page_remove_rmap(page)
atomic_add_negative(-1, &page->_mapcount)
The second bug[2] is "kernel BUG at mm/huge_memory.c:1371!".
It's VM_BUG_ON_PAGE(!PageHead(page), page) in zap_huge_pmd().
This happens in similar way:
CPU0 CPU1
zap_huge_pmd()
pmdp_get_and_clear()
page_remove_rmap(page)
atomic_add_negative(-1, &page->_mapcount)
__split_huge_page()
anon_vma_interval_tree_foreach()
__split_huge_page_splitting()
page_check_address_pmd()
mm_find_pmd()
pmd_present(pmd) == 0 /* The same comment as above */
/*
* No crash this time since we already decremented page->_mapcount in
* zap_huge_pmd().
*/
BUG_ON(mapcount != page_mapcount(page))
/*
* We split the compound page here into small pages without
* serialization against zap_huge_pmd()
*/
__split_huge_page_refcount()
VM_BUG_ON_PAGE(!PageHead(page), page); // CRASH!!!
So my understanding the problem is pmd_present() check in mm_find_pmd()
without taking page table lock.
The bug was introduced by me commit with commit 117b0791ac42. Sorry for
that. :(
Let's open code mm_find_pmd() in page_check_address_pmd() and do the
check under page table lock.
Note that __page_check_address() does the same for PTE entires
if sync != 0.
I've stress tested split and zap code paths for 36+ hours by now and
don't see crashes with the patch applied. Before it took <20 min to
trigger the first bug and few hours for second one (if we ignore
first).
[1] https://lkml.kernel.org/g/<53440991.9090001@oracle.com>
[2] https://lkml.kernel.org/g/<5310C56C.60709@oracle.com>
Signed-off-by: Kirill A. Shutemov <kirill.shutemov@linux.intel.com>
Reported-by: Sasha Levin <sasha.levin@oracle.com>
Tested-by: Sasha Levin <sasha.levin@oracle.com>
Cc: Bob Liu <lliubbo@gmail.com>
Cc: Andrea Arcangeli <aarcange@redhat.com>
Cc: Rik van Riel <riel@redhat.com>
Cc: Mel Gorman <mgorman@suse.de>
Cc: Michel Lespinasse <walken@google.com>
Cc: Dave Jones <davej@redhat.com>
Cc: Vlastimil Babka <vbabka@suse.cz>
Cc: <stable@vger.kernel.org> [3.13+]
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
Fix new kernel-doc warning in mm/filemap.c:
Warning(mm/filemap.c:2600): Excess function parameter 'ppos' description in '__generic_file_aio_write'
Signed-off-by: Randy Dunlap <rdunlap@infradead.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
This appears to be a copy/paste error. Update the description to
reflect extra rbtree debug and checks for the config option instead of
duplicating CONFIG_DEBUG_VM.
Signed-off-by: Davidlohr Bueso <davidlohr@hp.com>
Cc: Aswin Chandramouleeswaran <aswin@hp.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
David Vrabel identified a regression when using automatic NUMA balancing
under Xen whereby page table entries were getting corrupted due to the
use of native PTE operations. Quoting him
Xen PV guest page tables require that their entries use machine
addresses if the preset bit (_PAGE_PRESENT) is set, and (for
successful migration) non-present PTEs must use pseudo-physical
addresses. This is because on migration MFNs in present PTEs are
translated to PFNs (canonicalised) so they may be translated back
to the new MFN in the destination domain (uncanonicalised).
pte_mknonnuma(), pmd_mknonnuma(), pte_mknuma() and pmd_mknuma()
set and clear the _PAGE_PRESENT bit using pte_set_flags(),
pte_clear_flags(), etc.
In a Xen PV guest, these functions must translate MFNs to PFNs
when clearing _PAGE_PRESENT and translate PFNs to MFNs when setting
_PAGE_PRESENT.
His suggested fix converted p[te|md]_[set|clear]_flags to using
paravirt-friendly ops but this is overkill. He suggested an alternative
of using p[te|md]_modify in the NUMA page table operations but this is
does more work than necessary and would require looking up a VMA for
protections.
This patch modifies the NUMA page table operations to use paravirt
friendly operations to set/clear the flags of interest. Unfortunately
this will take a performance hit when updating the PTEs on
CONFIG_PARAVIRT but I do not see a way around it that does not break
Xen.
Signed-off-by: Mel Gorman <mgorman@suse.de>
Acked-by: David Vrabel <david.vrabel@citrix.com>
Tested-by: David Vrabel <david.vrabel@citrix.com>
Cc: Ingo Molnar <mingo@kernel.org>
Cc: Peter Anvin <hpa@zytor.com>
Cc: Fengguang Wu <fengguang.wu@intel.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Steven Noonan <steven@uplinklabs.net>
Cc: Rik van Riel <riel@redhat.com>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Andrea Arcangeli <aarcange@redhat.com>
Cc: Dave Hansen <dave.hansen@intel.com>
Cc: Srikar Dronamraju <srikar@linux.vnet.ibm.com>
Cc: Cyrill Gorcunov <gorcunov@gmail.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
The lkdtm module performs tests against executable memory ranges, so it
needs to flush the icache for proper behaviors. Other architectures
already export this, so do the same for MIPS.
[akpm@linux-foundation.org: relocate export sites]
Signed-off-by: Kees Cook <keescook@chromium.org>
Cc: Paul Gortmaker <paul.gortmaker@windriver.com>
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: Sanjay Lal <sanjayl@kymasys.com>
Cc: John Crispin <blogic@openwrt.org>
Cc: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
soft lockup in freeing gigantic hugepage fixed in commit 55f67141a892 "mm:
hugetlb: fix softlockup when a large number of hugepages are freed." can
happen in return_unused_surplus_pages(), so let's fix it.
Signed-off-by: Masayoshi Mizuma <m.mizuma@jp.fujitsu.com>
Signed-off-by: Naoya Horiguchi <n-horiguchi@ah.jp.nec.com>
Cc: Joonsoo Kim <iamjoonsoo.kim@lge.com>
Cc: Michal Hocko <mhocko@suse.cz>
Cc: Aneesh Kumar <aneesh.kumar@linux.vnet.ibm.com>
Cc: KOSAKI Motohiro <kosaki.motohiro@jp.fujitsu.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
Stick in a comment before someone else tries to fix the sparse warning
this generates.
Suggested-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Peter Zijlstra <peterz@infradead.org>
Link: http://lkml.kernel.org/n/tip-o2ro6f3vkxklni0bc8f7m68s@git.kernel.org
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
shiraz.hashim@st.com email-id doesn't exist anymore as he has left the
company. Replace ST's id with shiraz.linux.kernel@gmail.com.
It also updates .mailmap file to fix address for 'git shortlog'.
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Cc: Shiraz Hashim <shiraz.linux.kernel@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
numa_memory_policy.txt
In document numa_memory_policy.txt, the following examples for flag
MPOL_F_RELATIVE_NODES are incorrect.
For example, consider a task that is attached to a cpuset with
mems 2-5 that sets an Interleave policy over the same set with
MPOL_F_RELATIVE_NODES. If the cpuset's mems change to 3-7, the
interleave now occurs over nodes 3,5-6. If the cpuset's mems
then change to 0,2-3,5, then the interleave occurs over nodes
0,3,5.
According to the comment of the patch adding flag MPOL_F_RELATIVE_NODES,
the nodemasks the user specifies should be considered relative to the
current task's mems_allowed.
(https://lkml.org/lkml/2008/2/29/428)
And according to numa_memory_policy.txt, if the user's nodemask includes
nodes that are outside the range of the new set of allowed nodes, then
the remap wraps around to the beginning of the nodemask and, if not
already set, sets the node in the mempolicy nodemask.
So in the example, if the user specifies 2-5, for a task whose
mems_allowed is 3-7, the nodemasks should be remapped the third, fourth,
fifth, sixth node in mems_allowed. like the following:
mems_allowed: 3 4 5 6 7
relative index: 0 1 2 3 4
5
So the nodemasks should be remapped to 3,5-7, but not 3,5-6.
And for a task whose mems_allowed is 0,2-3,5, the nodemasks should be
remapped to 0,2-3,5, but not 0,3,5.
mems_allowed: 0 2 3 5
relative index: 0 1 2 3
4 5
Signed-off-by: Tang Chen <tangchen@cn.fujitsu.com>
Cc: Randy Dunlap <rdunlap@infradead.org>
Acked-by: David Rientjes <rientjes@google.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
CHK include/config/kernel.release
CHK include/generated/uapi/linux/version.h
CHK include/generated/utsrelease.h
...
Building modules, stage 2.
WARNING: 1 bad relocations
c0000000013d6a30 R_PPC64_ADDR64 uprobes_fetch_type_table
WRAP arch/powerpc/boot/zImage.pseries
WRAP arch/powerpc/boot/zImage.epapr
MODPOST 1849 modules
ERROR: ".__node_distance" [drivers/block/nvme.ko] undefined!
make[1]: *** [__modpost] Error 1
make: *** [modules] Error 2
make: *** Waiting for unfinished jobs....
The reason is symbol "__node_distance" not been exported in powerpc.
Signed-off-by: Mike Qiu <qiudayu@linux.vnet.ibm.com>
Acked-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Paul Mackerras <paulus@samba.org>
Cc: Nathan Fontenot <nfont@linux.vnet.ibm.com>
Cc: Stephen Rothwell <sfr@canb.auug.org.au>
Cc: Srivatsa S. Bhat <srivatsa.bhat@linux.vnet.ibm.com>
Cc: Jesse Larrew <jlarrew@linux.vnet.ibm.com>
Cc: Robert Jennings <rcj@linux.vnet.ibm.com>
Cc: Alistair Popple <alistair@popple.id.au>
Cc: Mike Qiu <qiudayu@linux.vnet.ibm.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
Fix:
BUG: using __this_cpu_write() in preemptible [00000000] code: systemd-udevd/497
caller is __this_cpu_preempt_check+0x13/0x20
CPU: 3 PID: 497 Comm: systemd-udevd Tainted: G W 3.15.0-rc1 #9
Hardware name: Hewlett-Packard HP EliteBook 8470p/179B, BIOS 68ICF Ver. F.02 04/27/2012
Call Trace:
check_preemption_disabled+0xe1/0xf0
__this_cpu_preempt_check+0x13/0x20
touch_nmi_watchdog+0x28/0x40
Reported-by: Luis Henriques <luis.henriques@canonical.com>
Tested-by: Luis Henriques <luis.henriques@canonical.com>
Cc: Eric Piel <eric.piel@tremplin-utc.net>
Cc: Robert Moore <robert.moore@intel.com>
Cc: Lv Zheng <lv.zheng@intel.com>
Cc: "Rafael J. Wysocki" <rafael.j.wysocki@intel.com>
Cc: Len Brown <lenb@kernel.org>
Cc: Christoph Lameter <cl@linux.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
