| Age | Commit message (Collapse) | Author |
|---|
|
The bcmgenet EEE implementation is broken in several ways.
phy_support_eee() is never called, so the PHY never advertises EEE
and phylib never sets phydev->enable_tx_lpi. bcmgenet_mac_config()
checks priv->eee.eee_enabled to decide whether to enable the MAC
LPI logic, but that field is never initialised to true, so the MAC
never enters Low Power Idle even when EEE is negotiated - wasting
the power savings EEE is designed to provide. The only way to get
EEE working at all is a manual 'ethtool --set-eee eth0 eee on' after
every link-up, and even then bcmgenet_get_eee() immediately clobbers
the reported state because phy_ethtool_get_eee() overwrites
eee_enabled and tx_lpi_enabled with the uninitialised PHY eee_cfg
values. Finally, bcmgenet_mac_config() is only called on link-up,
so EEE is never disabled in hardware on link-down.
Fix all of this by removing the MAC-side EEE state tracking
(priv->eee) and aligning with the pattern used by other non-phylink
MAC drivers such as FEC.
Call phy_support_eee() in bcmgenet_mii_probe() so the PHY advertises
EEE link modes and phylib tracks negotiation state. Move the EEE
hardware control to bcmgenet_mii_setup(), which is called on every
link event, and drive it directly from phydev->enable_tx_lpi - the
flag phylib sets when EEE is negotiated and the user has not disabled
it. This enables EEE automatically once the link partner agrees and
disables it cleanly on link-down.
Make bcmgenet_get_eee() and bcmgenet_set_eee() pure passthroughs to
phy_ethtool_get_eee() and phy_ethtool_set_eee(), with the MAC
hardware register read/written for tx_lpi_timer. Drop struct
ethtool_keee eee from struct bcmgenet_priv.
Fixes: fe0d4fd9285e ("net: phy: Keep track of EEE configuration")
Link: https://lore.kernel.org/netdev/d352039f-4cbb-41e6-9aeb-0b4f3941b54c@lunn.ch/
Suggested-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Nicolai Buchwitz <nb@tipi-net.de>
Reviewed-by: Florian Fainelli <florian.fainelli@broadcom.com>
Tested-by: Florian Fainelli <florian.fainelli@broadcom.com>
Link: https://patch.msgid.link/20260310054935.1238594-1-nb@tipi-net.de
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
genlmsg_reply() hands the reply skb to netlink, and
netlink_unicast() consumes it on all return paths, whether the
skb is queued successfully or freed on an error path.
net_shaper_nl_get_doit() and net_shaper_nl_cap_get_doit()
currently jump to free_msg after genlmsg_reply() fails and call
nlmsg_free(msg), which can hit the same skb twice.
Return the genlmsg_reply() error directly and keep free_msg
only for pre-reply failures.
Fixes: 4b623f9f0f59 ("net-shapers: implement NL get operation")
Fixes: 553ea9f1efd6 ("net: shaper: implement introspection support")
Cc: stable@vger.kernel.org
Signed-off-by: Paul Moses <p@1g4.org>
Link: https://patch.msgid.link/20260309173450.538026-2-p@1g4.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
The PHY addresses in the MII bus are not equal to the port addresses,
so the bus cannot be assigned as user_mii_bus. Falling back on the
user_mii_bus in case a PHY isn't declared in device tree will result in
using the wrong (in this case: off-by-+1) PHY.
Remove the wrong assignment.
Fixes: 23794bec1cb60 ("net: dsa: add basic initial driver for MxL862xx switches")
Suggested-by: Vladimir Oltean <olteanv@gmail.com>
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Reviewed-by: Vladimir Oltean <olteanv@gmail.com>
Link: https://patch.msgid.link/0f0df310fd8cab57e0e5e3d0831dd057fd05bcd5.1773103271.git.daniel@makrotopia.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Normal RX/TX interrupts are enabled later, in arc_emac_open(), so probe
should not see interrupt delivery in the usual case. However, hardware may
still present stale or latched interrupt status left by firmware or the
bootloader.
If probe later unwinds after devm_request_irq() has installed the handler,
such a stale interrupt can still reach arc_emac_intr() during teardown and
race with release of the associated net_device.
Avoid that window by putting the device into a known quiescent state before
requesting the IRQ: disable all EMAC interrupt sources and clear any
pending EMAC interrupt status bits. This keeps the change hardware-focused
and minimal, while preventing spurious IRQ delivery from leftover state.
Fixes: e4f2379db6c6 ("ethernet/arc/arc_emac - Add new driver")
Cc: stable@vger.kernel.org
Signed-off-by: Fan Wu <fanwu01@zju.edu.cn>
Link: https://patch.msgid.link/20260309132409.584966-1-fanwu01@zju.edu.cn
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
While testing other changes in vng I noticed that
nl_netdev.page_pool_check flakes. This never happens in real CI.
Turns out vng may boot and get to that test in less than a second.
page_pool_detached() records the detach time in seconds, so if
vng is fast enough detach time is set to 0. Other code treats
0 as "not detached". detach_time is only used to report the state
to the user, so it's not a huge deal in practice but let's fix it.
Store the raw ktime_t (nanoseconds) instead. A nanosecond value
of 0 is practically impossible.
Acked-by: Jesper Dangaard Brouer <hawk@kernel.org>
Fixes: 69cb4952b6f6 ("net: page_pool: report when page pool was destroyed")
Link: https://patch.msgid.link/20260310003907.3540019-1-kuba@kernel.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Quanyang observed that when using an NFS rootfs on an AMD ZynqMp board,
the rootfs may take an extended time to recover after a suspend.
Upon investigation, it was determined that the issue originates from a
problem in the macb driver.
According to the Zynq UltraScale TRM [1], when transmit is disabled,
the transmit buffer queue pointer resets to point to the address
specified by the transmit buffer queue base address register.
In the current implementation, the code merely resets `queue->tx_head`
and `queue->tx_tail` to '0'. This approach presents several issues:
- Packets already queued in the tx ring are silently lost,
leading to memory leaks since the associated skbs cannot be released.
- Concurrent write access to `queue->tx_head` and `queue->tx_tail` may
occur from `macb_tx_poll()` or `macb_start_xmit()` when these values
are reset to '0'.
- The transmission may become stuck on a packet that has already been sent
out, with its 'TX_USED' bit set, but has not yet been processed. However,
due to the manipulation of 'queue->tx_head' and 'queue->tx_tail',
`macb_tx_poll()` incorrectly assumes there are no packets to handle
because `queue->tx_head == queue->tx_tail`. This issue is only resolved
when a new packet is placed at this position. This is the root cause of
the prolonged recovery time observed for the NFS root filesystem.
To resolve this issue, shuffle the tx ring and tx skb array so that
the first unsent packet is positioned at the start of the tx ring.
Additionally, ensure that updates to `queue->tx_head` and
`queue->tx_tail` are properly protected with the appropriate lock.
[1] https://docs.amd.com/v/u/en-US/ug1085-zynq-ultrascale-trm
Fixes: bf9cf80cab81 ("net: macb: Fix tx/rx malfunction after phy link down and up")
Reported-by: Quanyang Wang <quanyang.wang@windriver.com>
Signed-off-by: Kevin Hao <haokexin@gmail.com>
Cc: stable@vger.kernel.org
Reviewed-by: Simon Horman <horms@kernel.org>
Link: https://patch.msgid.link/20260307-zynqmp-v2-1-6ef98a70e1d0@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Add Intel Nova Lake PCD-H SPI serial flash PCI ID to the list of
supported devices.
Signed-off-by: Alan Borzeszkowski <alan.borzeszkowski@linux.intel.com>
Acked-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Link: https://patch.msgid.link/20260309153703.74282-1-alan.borzeszkowski@linux.intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
If an error is encountered while mapping TX buffers, the driver should
unmap any buffers already mapped for that skb.
Because count is incremented after a successful mapping, it will always
match the correct number of unmappings needed when dma_error is reached.
Decrementing count before the while loop in dma_error causes an
off-by-one error. If any mapping was successful before an unsuccessful
mapping, exactly one DMA mapping would leak.
In these commits, a faulty while condition caused an infinite loop in
dma_error:
Commit 03b1320dfcee ("e1000e: remove use of skb_dma_map from e1000e
driver")
Commit 602c0554d7b0 ("e1000: remove use of skb_dma_map from e1000 driver")
Commit c1fa347f20f1 ("e1000/e1000e/igb/igbvf/ixgb/ixgbe: Fix tests of
unsigned in *_tx_map()") fixed the infinite loop, but introduced the
off-by-one error.
This issue may still exist in the igbvf driver, but I did not address it
in this patch.
Fixes: c1fa347f20f1 ("e1000/e1000e/igb/igbvf/ixgb/ixgbe: Fix tests of unsigned in *_tx_map()")
Assisted-by: Claude:claude-4.6-opus
Signed-off-by: Matt Vollrath <tactii@gmail.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
|
|
Fix following issues in the IPv4 and IPv6 cloud filter handling logic in
both the add and delete paths:
- The source-IP mask check incorrectly compares mask.src_ip[0] against
tcf.dst_ip[0]. Update it to compare against tcf.src_ip[0]. This likely
goes unnoticed because the check is in an "else if" path that only
executes when dst_ip is not set, most cloud filter use cases focus on
destination-IP matching, and the buggy condition can accidentally
evaluate true in some cases.
- memcpy() for the IPv4 source address incorrectly uses
ARRAY_SIZE(tcf.dst_ip) instead of ARRAY_SIZE(tcf.src_ip), although
both arrays are the same size.
- The IPv4 memcpy operations used ARRAY_SIZE(tcf.dst_ip) and ARRAY_SIZE
(tcf.src_ip), Update these to use sizeof(cfilter->ip.v4.dst_ip) and
sizeof(cfilter->ip.v4.src_ip) to ensure correct and explicit copy size.
- In the IPv6 delete path, memcmp() uses sizeof(src_ip6) when comparing
dst_ip6 fields. Replace this with sizeof(dst_ip6) to make the intent
explicit, even though both fields are struct in6_addr.
Fixes: e284fc280473 ("i40e: Add and delete cloud filter")
Signed-off-by: Alok Tiwari <alok.a.tiwari@oracle.com>
Reviewed-by: Aleksandr Loktionov <aleksandr.loktionov@intel.com>
Reviewed-by: Paul Menzel <pmenzel@molgen.mpg.de>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/akpm/mm
Pull misc fixes from Andrew Morton:
"15 hotfixes. 6 are cc:stable. 14 are for MM.
Singletons, with one doubleton - please see the changelogs for details"
* tag 'mm-hotfixes-stable-2026-03-09-16-36' of git://git.kernel.org/pub/scm/linux/kernel/git/akpm/mm:
MAINTAINERS, mailmap: update email address for Lorenzo Stoakes
mm/mmu_notifier: clean up mmu_notifier.h kernel-doc
uaccess: correct kernel-doc parameter format
mm/huge_memory: fix a folio_split() race condition with folio_try_get()
MAINTAINERS: add co-maintainer and reviewer for SLAB ALLOCATOR
MAINTAINERS: add RELAY entry
memcg: fix slab accounting in refill_obj_stock() trylock path
mm/hugetlb.c: use __pa() instead of virt_to_phys() in early bootmem alloc code
zram: rename writeback_compressed device attr
tools/testing: fix testing/vma and testing/radix-tree build
Revert "ptdesc: remove references to folios from __pagetable_ctor() and pagetable_dtor()"
mm/cma: move put_page_testzero() out of VM_WARN_ON in cma_release()
mm/damon/core: clear walk_control on inactive context in damos_walk()
mm: memfd_luo: always dirty all folios
mm: memfd_luo: always make all folios uptodate
|
|
The correct helper to use in rt1011_recv_spk_mode_put() to retrieve the
DAPM context is snd_soc_component_to_dapm(), from kcontrol we will
receive NULL pointer.
Closes: https://github.com/thesofproject/linux/issues/5691
Fixes: 5b35bb517f27 ("ASoC: codecs: rt1011: convert to snd_soc_dapm_xxx()")
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@linux.intel.com>
Link: https://patch.msgid.link/20260310065350.18921-1-peter.ujfalusi@linux.intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
Three driver callbacks schedule a reset and wait for its completion:
ndo_change_mtu(), ethtool set_ringparam(), and ethtool set_channels().
Waiting for reset in ndo_change_mtu() and set_ringparam() was added by
commit c2ed2403f12c ("iavf: Wait for reset in callbacks which trigger
it") to fix a race condition where adding an interface to bonding
immediately after MTU or ring parameter change failed because the
interface was still in __RESETTING state. The same commit also added
waiting in iavf_set_priv_flags(), which was later removed by commit
53844673d555 ("iavf: kill "legacy-rx" for good").
Waiting in set_channels() was introduced earlier by commit 4e5e6b5d9d13
("iavf: Fix return of set the new channel count") to ensure the PF has
enough time to complete the VF reset when changing channel count, and to
return correct error codes to userspace.
Commit ef490bbb2267 ("iavf: Add net_shaper_ops support") added
net_shaper_ops to iavf, which required reset_task to use _locked NAPI
variants (napi_enable_locked, napi_disable_locked) that need the netdev
instance lock.
Later, commit 7e4d784f5810 ("net: hold netdev instance lock during
rtnetlink operations") and commit 2bcf4772e45a ("net: ethtool: try to
protect all callback with netdev instance lock") started holding the
netdev instance lock during ndo and ethtool callbacks for drivers with
net_shaper_ops.
Finally, commit 120f28a6f314 ("iavf: get rid of the crit lock")
replaced the driver's crit_lock with netdev_lock in reset_task, causing
incorrect behavior: the callback holds netdev_lock and waits for
reset_task, but reset_task needs the same lock:
Thread 1 (callback) Thread 2 (reset_task)
------------------- ---------------------
netdev_lock() [blocked on workqueue]
ndo_change_mtu() or ethtool op
iavf_schedule_reset()
iavf_wait_for_reset() iavf_reset_task()
waiting... netdev_lock() <- blocked
This does not strictly deadlock because iavf_wait_for_reset() uses
wait_event_interruptible_timeout() with a 5-second timeout. The wait
eventually times out, the callback returns an error to userspace, and
after the lock is released reset_task completes the reset. This leads to
incorrect behavior: userspace sees an error even though the configuration
change silently takes effect after the timeout.
Fix this by extracting the reset logic from iavf_reset_task() into a new
iavf_reset_step() function that expects netdev_lock to be already held.
The three callbacks now call iavf_reset_step() directly instead of
scheduling the work and waiting, performing the reset synchronously in
the caller's context which already holds netdev_lock. This eliminates
both the incorrect error reporting and the need for
iavf_wait_for_reset(), which is removed along with the now-unused
reset_waitqueue.
The workqueue-based iavf_reset_task() becomes a thin wrapper that
acquires netdev_lock and calls iavf_reset_step(), preserving its use
for PF-initiated resets.
The callbacks may block for several seconds while iavf_reset_step()
polls hardware registers, but this is acceptable since netdev_lock is a
per-device mutex and only serializes operations on the same interface.
v3:
- Remove netif_running() guard from iavf_set_channels(). Unlike
set_ringparam where descriptor counts are picked up by iavf_open()
directly, num_req_queues is only consumed during
iavf_reinit_interrupt_scheme() in the reset path. Skipping the reset
on a down device would silently discard the channel count change.
- Remove dead reset_waitqueue code (struct field, init, and all
wake_up calls) since iavf_wait_for_reset() was the only consumer.
Fixes: 120f28a6f314 ("iavf: get rid of the crit lock")
Reviewed-by: Jacob Keller <jacob.e.keller@intel.com>
Signed-off-by: Petr Oros <poros@redhat.com>
Reviewed-by: Przemek Kitszel <przemyslaw.kitszel@intel.com>
Tested-by: Rafal Romanowski <rafal.romanowski@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
|
|
Commit 7c01dbfc8a1c5f ("iavf: periodically cache PHC time") introduced a
worker to cache PHC time, but failed to stop it during reset or disable.
This creates a race condition where `iavf_reset_task()` or
`iavf_disable_vf()` free adapter resources (AQ) while the worker is still
running. If the worker triggers `iavf_queue_ptp_cmd()` during teardown, it
accesses freed memory/locks, leading to a crash.
Fix this by calling `iavf_ptp_release()` before tearing down the adapter.
This ensures `ptp_clock_unregister()` synchronously cancels the worker and
cleans up the chardev before the backing resources are destroyed.
Fixes: 7c01dbfc8a1c5f ("iavf: periodically cache PHC time")
Signed-off-by: Petr Oros <poros@redhat.com>
Reviewed-by: Ivan Vecera <ivecera@redhat.com>
Acked-by: Jacob Keller <jacob.e.keller@intel.com>
Reviewed-by: Vadim Fedorenko <vadim.fedorenko@linux.dev>
Reviewed-by: Paul Menzel <pmenzel@molgen.mpg.de>
Reviewed-by: Aleksandr Loktionov <aleksandr.loktionov@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
|
|
If CONFIG_IRDMA isn't enabled but there are ice NICs in the system, the
driver will prevent full devlink dev param show dump because its rdma get
callbacks return ENODEV and stop the dump. For example:
$ devlink dev param show
pci/0000:82:00.0:
name msix_vec_per_pf_max type generic
values:
cmode driverinit value 2
name msix_vec_per_pf_min type generic
values:
cmode driverinit value 2
kernel answers: No such device
Returning EOPNOTSUPP allows the dump to continue so we can see all devices'
devlink parameters.
Fixes: c24a65b6a27c ("iidc/ice/irdma: Update IDC to support multiple consumers")
Signed-off-by: Nikolay Aleksandrov <nikolay@nvidia.com>
Tested-by: Rinitha S <sx.rinitha@intel.com> (A Contingent worker at Intel)
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
|
|
Add the __counted_by() compiler attribute to the flexible array member
'key' to improve access bounds-checking via CONFIG_UBSAN_BOUNDS and
CONFIG_FORTIFY_SOURCE.
Reviewed-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Thorsten Blum <thorsten.blum@linux.dev>
Signed-off-by: Keith Busch <kbusch@kernel.org>
|
|
In nvme_alloc_admin_tag_set(), an empty queue_limits struct is
currently allocated on the stack and passed by reference to
blk_mq_alloc_queue().
This is redundant because blk_mq_alloc_queue() already handles
a NULL limits pointer by internally substituting it with a default
empty queue_limits struct.
Remove the unnecessary local variable and pass a NULL value.
Reviewed-by: Kanchan Joshi <joshi.k@samsung.com>
Signed-off-by: Maurizio Lombardi <mlombard@redhat.com>
Signed-off-by: Keith Busch <kbusch@kernel.org>
|
|
In the following scenario, pdev can be disabled between (1) and (3) by
(2). This sets pdev->msix_enabled = 0. Then, pci_irq_vector() will
return MSI-X IRQ(>15) for (1) whereas return INTx IRQ(<=15) for (2).
This causes IRQ warning because it tries to enable INTx IRQ that has
never been disabled before.
To fix this, save IRQ number into a local variable and ensure
disable_irq() and enable_irq() operate on the same IRQ number. Even if
pci_free_irq_vectors() frees the IRQ concurrently, disable_irq() and
enable_irq() on a stale IRQ number is still valid and safe, and the
depth accounting reamins balanced.
task 1:
nvme_poll_irqdisable()
disable_irq(pci_irq_vector(pdev, nvmeq->cq_vector)) ...(1)
enable_irq(pci_irq_vector(pdev, nvmeq->cq_vector)) ...(3)
task 2:
nvme_reset_work()
nvme_dev_disable()
pdev->msix_enable = 0; ...(2)
crash log:
------------[ cut here ]------------
Unbalanced enable for IRQ 10
WARNING: kernel/irq/manage.c:753 at __enable_irq+0x102/0x190 kernel/irq/manage.c:753, CPU#1: kworker/1:0H/26
Modules linked in:
CPU: 1 UID: 0 PID: 26 Comm: kworker/1:0H Not tainted 6.19.0-dirty #9 PREEMPT(voluntary)
Hardware name: QEMU Standard PC (i440FX + PIIX, 1996), BIOS rel-1.16.3-0-ga6ed6b701f0a-prebuilt.qemu.org 04/01/2014
Workqueue: kblockd blk_mq_timeout_work
RIP: 0010:__enable_irq+0x107/0x190 kernel/irq/manage.c:753
Code: ff df 48 89 fa 48 c1 ea 03 0f b6 14 02 48 89 f8 83 e0 07 83 c0 03 38 d0 7c 04 84 d2 75 79 48 8d 3d 2e 7a 3f 05 41 8b 74 24 2c <67> 48 0f b9 3a e8 ef b9 21 00 5b 41 5c 5d e9 46 54 66 03 e8 e1 b9
RSP: 0018:ffffc900001bf550 EFLAGS: 00010046
RAX: 0000000000000007 RBX: 0000000000000000 RCX: ffffffffb20c0e90
RDX: 0000000000000000 RSI: 000000000000000a RDI: ffffffffb74b88f0
RBP: ffffc900001bf560 R08: ffff88800197cf00 R09: 0000000000000001
R10: 0000000000000003 R11: 0000000000000003 R12: ffff8880012a6000
R13: 1ffff92000037eae R14: 000000000000000a R15: 0000000000000293
FS: 0000000000000000(0000) GS:ffff8880b49f7000(0000) knlGS:0000000000000000
CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033
CR2: 0000555da4a25fa8 CR3: 00000000208e8000 CR4: 00000000000006f0
Call Trace:
<TASK>
enable_irq+0x121/0x1e0 kernel/irq/manage.c:797
nvme_poll_irqdisable+0x162/0x1c0 drivers/nvme/host/pci.c:1494
nvme_timeout+0x965/0x14b0 drivers/nvme/host/pci.c:1744
blk_mq_rq_timed_out block/blk-mq.c:1653 [inline]
blk_mq_handle_expired+0x227/0x2d0 block/blk-mq.c:1721
bt_iter+0x2fc/0x3a0 block/blk-mq-tag.c:292
__sbitmap_for_each_set include/linux/sbitmap.h:269 [inline]
sbitmap_for_each_set include/linux/sbitmap.h:290 [inline]
bt_for_each block/blk-mq-tag.c:324 [inline]
blk_mq_queue_tag_busy_iter+0x969/0x1e80 block/blk-mq-tag.c:536
blk_mq_timeout_work+0x627/0x870 block/blk-mq.c:1763
process_one_work+0x956/0x1aa0 kernel/workqueue.c:3257
process_scheduled_works kernel/workqueue.c:3340 [inline]
worker_thread+0x65c/0xe60 kernel/workqueue.c:3421
kthread+0x41a/0x930 kernel/kthread.c:463
ret_from_fork+0x6f8/0x8c0 arch/x86/kernel/process.c:158
ret_from_fork_asm+0x1a/0x30 arch/x86/entry/entry_64.S:246
</TASK>
irq event stamp: 74478
hardirqs last enabled at (74477): [<ffffffffb5720a9c>] __raw_spin_unlock_irq include/linux/spinlock_api_smp.h:159 [inline]
hardirqs last enabled at (74477): [<ffffffffb5720a9c>] _raw_spin_unlock_irq+0x2c/0x60 kernel/locking/spinlock.c:202
hardirqs last disabled at (74478): [<ffffffffb57207b5>] __raw_spin_lock_irqsave include/linux/spinlock_api_smp.h:108 [inline]
hardirqs last disabled at (74478): [<ffffffffb57207b5>] _raw_spin_lock_irqsave+0x85/0xa0 kernel/locking/spinlock.c:162
softirqs last enabled at (74304): [<ffffffffb1e9466c>] __do_softirq kernel/softirq.c:656 [inline]
softirqs last enabled at (74304): [<ffffffffb1e9466c>] invoke_softirq kernel/softirq.c:496 [inline]
softirqs last enabled at (74304): [<ffffffffb1e9466c>] __irq_exit_rcu+0xdc/0x120 kernel/softirq.c:723
softirqs last disabled at (74287): [<ffffffffb1e9466c>] __do_softirq kernel/softirq.c:656 [inline]
softirqs last disabled at (74287): [<ffffffffb1e9466c>] invoke_softirq kernel/softirq.c:496 [inline]
softirqs last disabled at (74287): [<ffffffffb1e9466c>] __irq_exit_rcu+0xdc/0x120 kernel/softirq.c:723
---[ end trace 0000000000000000 ]---
Fixes: fa059b856a59 (nvme-pci: Simplify nvme_poll_irqdisable)
Acked-by: Chao Shi <cshi008@fiu.edu>
Acked-by: Weidong Zhu <weizhu@fiu.edu>
Acked-by: Dave Tian <daveti@purdue.edu>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Sungwoo Kim <iam@sung-woo.kim>
Signed-off-by: Keith Busch <kbusch@kernel.org>
|
|
For target nvmet_ctrl_free() flushes ctrl->async_event_work.
If nvmet_ctrl_free() runs on nvmet-wq, the flush re-enters workqueue
completion for the same worker:-
A. Async event work queued on nvmet-wq (prior to disconnect):
nvmet_execute_async_event()
queue_work(nvmet_wq, &ctrl->async_event_work)
nvmet_add_async_event()
queue_work(nvmet_wq, &ctrl->async_event_work)
B. Full pre-work chain (RDMA CM path):
nvmet_rdma_cm_handler()
nvmet_rdma_queue_disconnect()
__nvmet_rdma_queue_disconnect()
queue_work(nvmet_wq, &queue->release_work)
process_one_work()
lock((wq_completion)nvmet-wq) <--------- 1st
nvmet_rdma_release_queue_work()
C. Recursive path (same worker):
nvmet_rdma_release_queue_work()
nvmet_rdma_free_queue()
nvmet_sq_destroy()
nvmet_ctrl_put()
nvmet_ctrl_free()
flush_work(&ctrl->async_event_work)
__flush_work()
touch_wq_lockdep_map()
lock((wq_completion)nvmet-wq) <--------- 2nd
Lockdep splat:
============================================
WARNING: possible recursive locking detected
6.19.0-rc3nvme+ #14 Tainted: G N
--------------------------------------------
kworker/u192:42/44933 is trying to acquire lock:
ffff888118a00948 ((wq_completion)nvmet-wq){+.+.}-{0:0}, at: touch_wq_lockdep_map+0x26/0x90
but task is already holding lock:
ffff888118a00948 ((wq_completion)nvmet-wq){+.+.}-{0:0}, at: process_one_work+0x53e/0x660
3 locks held by kworker/u192:42/44933:
#0: ffff888118a00948 ((wq_completion)nvmet-wq){+.+.}-{0:0}, at: process_one_work+0x53e/0x660
#1: ffffc9000e6cbe28 ((work_completion)(&queue->release_work)){+.+.}-{0:0}, at: process_one_work+0x1c5/0x660
#2: ffffffff82d4db60 (rcu_read_lock){....}-{1:3}, at: __flush_work+0x62/0x530
Workqueue: nvmet-wq nvmet_rdma_release_queue_work [nvmet_rdma]
Call Trace:
__flush_work+0x268/0x530
nvmet_ctrl_free+0x140/0x310 [nvmet]
nvmet_cq_put+0x74/0x90 [nvmet]
nvmet_rdma_free_queue+0x23/0xe0 [nvmet_rdma]
nvmet_rdma_release_queue_work+0x19/0x50 [nvmet_rdma]
process_one_work+0x206/0x660
worker_thread+0x184/0x320
kthread+0x10c/0x240
ret_from_fork+0x319/0x390
Move async event work to a dedicated nvmet-aen-wq to avoid reentrant
flush on nvmet-wq.
Reviewed-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Chaitanya Kulkarni <kch@nvidia.com>
Signed-off-by: Keith Busch <kbusch@kernel.org>
|
|
dev->online_queues is a count incremented in nvme_init_queue. Thus,
valid indices are 0 through dev->online_queues − 1.
This patch fixes the loop condition to ensure the index stays within the
valid range. Index 0 is excluded because it is the admin queue.
KASAN splat:
==================================================================
BUG: KASAN: slab-out-of-bounds in nvme_dbbuf_free drivers/nvme/host/pci.c:377 [inline]
BUG: KASAN: slab-out-of-bounds in nvme_dbbuf_set+0x39c/0x400 drivers/nvme/host/pci.c:404
Read of size 2 at addr ffff88800592a574 by task kworker/u8:5/74
CPU: 0 UID: 0 PID: 74 Comm: kworker/u8:5 Not tainted 6.19.0-dirty #10 PREEMPT(voluntary)
Hardware name: QEMU Standard PC (i440FX + PIIX, 1996), BIOS rel-1.16.3-0-ga6ed6b701f0a-prebuilt.qemu.org 04/01/2014
Workqueue: nvme-reset-wq nvme_reset_work
Call Trace:
<TASK>
__dump_stack lib/dump_stack.c:94 [inline]
dump_stack_lvl+0xea/0x150 lib/dump_stack.c:120
print_address_description mm/kasan/report.c:378 [inline]
print_report+0xce/0x5d0 mm/kasan/report.c:482
kasan_report+0xdc/0x110 mm/kasan/report.c:595
__asan_report_load2_noabort+0x18/0x20 mm/kasan/report_generic.c:379
nvme_dbbuf_free drivers/nvme/host/pci.c:377 [inline]
nvme_dbbuf_set+0x39c/0x400 drivers/nvme/host/pci.c:404
nvme_reset_work+0x36b/0x8c0 drivers/nvme/host/pci.c:3252
process_one_work+0x956/0x1aa0 kernel/workqueue.c:3257
process_scheduled_works kernel/workqueue.c:3340 [inline]
worker_thread+0x65c/0xe60 kernel/workqueue.c:3421
kthread+0x41a/0x930 kernel/kthread.c:463
ret_from_fork+0x6f8/0x8c0 arch/x86/kernel/process.c:158
ret_from_fork_asm+0x1a/0x30 arch/x86/entry/entry_64.S:246
</TASK>
Allocated by task 34 on cpu 1 at 4.241550s:
kasan_save_stack+0x2c/0x60 mm/kasan/common.c:57
kasan_save_track+0x1c/0x70 mm/kasan/common.c:78
kasan_save_alloc_info+0x3c/0x50 mm/kasan/generic.c:570
poison_kmalloc_redzone mm/kasan/common.c:398 [inline]
__kasan_kmalloc+0xb5/0xc0 mm/kasan/common.c:415
kasan_kmalloc include/linux/kasan.h:263 [inline]
__do_kmalloc_node mm/slub.c:5657 [inline]
__kmalloc_node_noprof+0x2bf/0x8d0 mm/slub.c:5663
kmalloc_array_node_noprof include/linux/slab.h:1075 [inline]
nvme_pci_alloc_dev drivers/nvme/host/pci.c:3479 [inline]
nvme_probe+0x2f1/0x1820 drivers/nvme/host/pci.c:3534
local_pci_probe+0xef/0x1c0 drivers/pci/pci-driver.c:324
pci_call_probe drivers/pci/pci-driver.c:392 [inline]
__pci_device_probe drivers/pci/pci-driver.c:417 [inline]
pci_device_probe+0x743/0x920 drivers/pci/pci-driver.c:451
call_driver_probe drivers/base/dd.c:583 [inline]
really_probe+0x29b/0xb70 drivers/base/dd.c:661
__driver_probe_device+0x3b0/0x4a0 drivers/base/dd.c:803
driver_probe_device+0x56/0x1f0 drivers/base/dd.c:833
__driver_attach_async_helper+0x155/0x340 drivers/base/dd.c:1159
async_run_entry_fn+0xa6/0x4b0 kernel/async.c:129
process_one_work+0x956/0x1aa0 kernel/workqueue.c:3257
process_scheduled_works kernel/workqueue.c:3340 [inline]
worker_thread+0x65c/0xe60 kernel/workqueue.c:3421
kthread+0x41a/0x930 kernel/kthread.c:463
ret_from_fork+0x6f8/0x8c0 arch/x86/kernel/process.c:158
ret_from_fork_asm+0x1a/0x30 arch/x86/entry/entry_64.S:246
The buggy address belongs to the object at ffff88800592a000
which belongs to the cache kmalloc-2k of size 2048
The buggy address is located 244 bytes to the right of
allocated 1152-byte region [ffff88800592a000, ffff88800592a480)
The buggy address belongs to the physical page:
page: refcount:0 mapcount:0 mapping:0000000000000000 index:0x0 pfn:0x5928
head: order:3 mapcount:0 entire_mapcount:0 nr_pages_mapped:0 pincount:0
anon flags: 0xfffffc0000040(head|node=0|zone=1|lastcpupid=0x1fffff)
page_type: f5(slab)
raw: 000fffffc0000040 ffff888001042000 0000000000000000 dead000000000001
raw: 0000000000000000 0000000000080008 00000000f5000000 0000000000000000
head: 000fffffc0000040 ffff888001042000 0000000000000000 dead000000000001
head: 0000000000000000 0000000000080008 00000000f5000000 0000000000000000
head: 000fffffc0000003 ffffea0000164a01 00000000ffffffff 00000000ffffffff
head: ffffffffffffffff 0000000000000000 00000000ffffffff 0000000000000008
page dumped because: kasan: bad access detected
Memory state around the buggy address:
ffff88800592a400: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
ffff88800592a480: fc fc fc fc fc fc fc fc fc fc fc fc fc fc fc fc
>ffff88800592a500: fc fc fc fc fc fc fc fc fc fc fc fc fc fc fc fc
^
ffff88800592a580: fc fc fc fc fc fc fc fc fc fc fc fc fc fc fc fc
ffff88800592a600: fc fc fc fc fc fc fc fc fc fc fc fc fc fc fc fc
==================================================================
Fixes: 0f0d2c876c96 (nvme: free sq/cq dbbuf pointers when dbbuf set fails)
Acked-by: Chao Shi <cshi008@fiu.edu>
Acked-by: Weidong Zhu <weizhu@fiu.edu>
Acked-by: Dave Tian <daveti@purdue.edu>
Signed-off-by: Sungwoo Kim <iam@sung-woo.kim>
Signed-off-by: Keith Busch <kbusch@kernel.org>
|
|
If the cpuidle governor .select() callback is skipped because there
is only one idle state in the cpuidle driver, the .reflect() callback
should be skipped as well, at least for consistency (if not for
correctness), so do it.
Fixes: e5c9ffc6ae1b ("cpuidle: Skip governor when only one idle state is available")
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Reviewed-by: Christian Loehle <christian.loehle@arm.com>
Reviewed-by: Aboorva Devarajan <aboorvad@linux.ibm.com>
Reviewed-by: Frederic Weisbecker <frederic@kernel.org>
Link: https://patch.msgid.link/12857700.O9o76ZdvQC@rafael.j.wysocki
|
|
During online processing for a DASD device an IO operation is started to
determine the format of the device. CDL format contains specifically
sized blocks at the beginning of the disk.
For a PPRC secondary device no real IO operation is possible therefore
this IO request can not be started and this step is skipped for online
processing of secondary devices. This is generally fine since the
secondary is a copy of the primary device.
In case of an additional partition detection that is run after a swap
operation the format information is needed to properly drive partition
detection IO.
Currently the information is not passed leading to IO errors during
partition detection and a wrongly detected partition table which in turn
might lead to data corruption on the disk with the wrong partition table.
Fix by passing the format information from primary to secondary device.
Fixes: 413862caad6f ("s390/dasd: add copy pair swap capability")
Cc: stable@vger.kernel.org #6.1
Reviewed-by: Jan Hoeppner <hoeppner@linux.ibm.com>
Acked-by: Eduard Shishkin <edward6@linux.ibm.com>
Signed-off-by: Stefan Haberland <sth@linux.ibm.com>
Link: https://patch.msgid.link/20260310142330.4080106-3-sth@linux.ibm.com
Signed-off-by: Jens Axboe <axboe@kernel.dk>
|
|
Quiesce and resume is a mechanism to suspend operations on DASD devices.
In the context of a controlled copy pair swap operation, the quiesce
operation is usually issued before the actual swap and a resume
afterwards.
During the swap operation, the underlying device is exchanged. Therefore,
the quiesce flag must be moved to the secondary device to ensure a
consistent quiesce state after the swap.
The secondary device itself cannot be suspended separately because there
is no separate block device representation for it.
Fixes: 413862caad6f ("s390/dasd: add copy pair swap capability")
Cc: stable@vger.kernel.org #6.1
Reviewed-by: Jan Hoeppner <hoeppner@linux.ibm.com>
Signed-off-by: Stefan Haberland <sth@linux.ibm.com>
Link: https://patch.msgid.link/20260310142330.4080106-2-sth@linux.ibm.com
Signed-off-by: Jens Axboe <axboe@kernel.dk>
|
|
An incorrect device name was logged for PCA9452 because the dev_info()
ternary omitted PCA9452 and fell through to "pca9450bc". Introduce a
type_name and set it per device type so the probed message matches the
actual PMIC. While here, make the PCA9451A case explicit.
No functional changes.
Fixes: 017b76fb8e5b6 ("regulator: pca9450: Add PMIC pca9452 support")
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Link: https://patch.msgid.link/20260310-pca9450-irq-v1-2-36adf52c2c55@nxp.com
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
Kernel warning on i.MX8MP-EVK when doing module test:
irq: type mismatch, failed to map hwirq-3 for gpio@30200000!
Per PCA945[X] specification: The IRQ_B pin is pulled low when any unmasked
interrupt bit status is changed and it is released high once application
processor read INT1 register.
So the interrupt should be configured as IRQF_TRIGGER_LOW, not
IRQF_TRIGGER_FALLING.
Fixes: 0935ff5f1f0a4 ("regulator: pca9450: add pca9450 pmic driver")
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Link: https://patch.msgid.link/20260310-pca9450-irq-v1-1-36adf52c2c55@nxp.com
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
The move of the AHB and APB clocks from a JH7110 specific quirk to the
main clock init dropped the specification of the clock names to request
for the AHB and APB clocks, resulting in the clock framework requesting
a clock with a NULL name three times. On most platforms where the
clocks are physically the same or some are always on this makes no
difference but the reason we had the specific quirk for JH7110 is that
it does actually have separate, controllable clocks. Update the new
code to request the AHB and APB clocks by name to restore the original
behaviour on JH7110.
Fixes: 324ecc7788c2 ("spi: cadence-qspi: Kill cqspi_jh7110_clk_init")
Reported-by: Ron Economos <re@w6rz.net>
Closes: https://lore.kernel.org/r/a3ca5e9b-7446-497e-8df2-7ef2b42a02e9@w6rz.net
Tested-by: Ron Economos <re@w6rz.net>
Link: https://patch.msgid.link/20260307-spi-cadence-qspi-fix-jh7110-v1-1-c9f37b8c58b1@kernel.org
Signed-off-by: Mark Brown <broonie@kernel.org>
Link: https://patch.msgid.link/20260307-spi-cadence-qspi-fix-jh7110-v1-1-c9f37b8c58b1@kernel.org
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/mkl/linux-can
Marc Kleine-Budde says:
====================
pull-request: can 2026-03-10
this is a pull request of 2 patches for net/main.
Haibo Chen's patch fixes the maximum allowed bit rate error, which was
broken in v6.19.
Wenyuan Li contributes a patch for the hi311x driver that adds missing
error checking in the caller of the hi3110_power_enable() function,
hi3110_open().
linux-can-fixes-for-7.0-20260310
* tag 'linux-can-fixes-for-7.0-20260310' of git://git.kernel.org/pub/scm/linux/kernel/git/mkl/linux-can:
can: hi311x: hi3110_open(): add check for hi3110_power_enable() return value
can: dev: keep the max bitrate error at 5%
====================
Link: https://patch.msgid.link/20260310103547.2299403-1-mkl@pengutronix.de
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
|
|
Commit 02c057ddefef ("ACPI: video: Convert the driver to a platform one")
switched over the ACPI video bus driver from an ACPI driver to a platform
driver, but that change introduced an unwanted and unexpected side effect.
Namely, on some systems, the ACPI device object of the ACPI video bus
device is an ACPI companion of multiple platform devices and, after
adding video_device_ids[] as an acpi_match_table to the acpi_video_bus
platform driver, all of those devices started to match that driver and
its probe callback is invoked for all of them (it fails, but it leaves
a confusing message in the log). Moreover, the MODULE_DEVICE_TABLE()
of the ACPI video driver module matches all of the devices sharing the
ACPI companion with the ACPI video bus device.
To address this, make the core ACPI device enumeration code create an
auxiliary device for the ACPI video bus device object instead of a
platform device and switch over the ACPI video bus driver (once more)
to an auxiliary driver.
Auxiliary driver generally is a better match for ACPI video bus than
platform driver, among other things because the ACPI video bus device
does not require any resources to be allocated for it during
enumeration. It also allows the ACPI video bus driver to stop abusing
device matching based on ACPI device IDs and it allows a special case
to be dropped from acpi_create_platform_device() because that function
need not worry about the ACPI video bus device any more.
Fixes: 02c057ddefef ("ACPI: video: Convert the driver to a platform one")
Reported-by: Pratap Nirujogi <pratap.nirujogi@amd.com>
Closes: https://lore.kernel.org/linux-acpi/007e3390-6b2b-457e-83c7-c794c5952018@amd.com/
Tested-by: Pratap Nirujogi <pratap.nirujogi@amd.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Reviewed-by: Mario Limonciello (AMD) <superm1@kernel.org>
[ rjw: Added AUXILIARY_BUS selection to CONFIG_ACPI to fix build issue ]
[ rjw: Fixed error path in acpi_create_video_bus_device() ]
Link: https://patch.msgid.link/5986516.DvuYhMxLoT@rafael.j.wysocki
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
|
|
IDLETIMER revision 0 rules reuse existing timers by label and always call
mod_timer() on timer->timer.
If the label was created first by revision 1 with XT_IDLETIMER_ALARM,
the object uses alarm timer semantics and timer->timer is never initialized.
Reusing that object from revision 0 causes mod_timer() on an uninitialized
timer_list, triggering debugobjects warnings and possible panic when
panic_on_warn=1.
Fix this by rejecting revision 0 rule insertion when an existing timer with
the same label is of ALARM type.
Fixes: 68983a354a65 ("netfilter: xtables: Add snapshot of hardidletimer target")
Co-developed-by: Yifan Wu <yifanwucs@gmail.com>
Signed-off-by: Yifan Wu <yifanwucs@gmail.com>
Co-developed-by: Juefei Pu <tomapufckgml@gmail.com>
Signed-off-by: Juefei Pu <tomapufckgml@gmail.com>
Signed-off-by: Yuan Tan <tanyuan98@outlook.com>
Signed-off-by: Xin Liu <dstsmallbird@foxmail.com>
Signed-off-by: Florian Westphal <fw@strlen.de>
|
|
nfnl_cthelper_dump_table() has a 'goto restart' that jumps to a label
inside the for loop body. When the "last" helper saved in cb->args[1]
is deleted between dump rounds, every entry fails the (cur != last)
check, so cb->args[1] is never cleared. The for loop finishes with
cb->args[0] == nf_ct_helper_hsize, and the 'goto restart' jumps back
into the loop body bypassing the bounds check, causing an 8-byte
out-of-bounds read on nf_ct_helper_hash[nf_ct_helper_hsize].
The 'goto restart' block was meant to re-traverse the current bucket
when "last" is no longer found, but it was placed after the for loop
instead of inside it. Move the block into the for loop body so that
the restart only occurs while cb->args[0] is still within bounds.
BUG: KASAN: slab-out-of-bounds in nfnl_cthelper_dump_table+0x9f/0x1b0
Read of size 8 at addr ffff888104ca3000 by task poc_cthelper/131
Call Trace:
nfnl_cthelper_dump_table+0x9f/0x1b0
netlink_dump+0x333/0x880
netlink_recvmsg+0x3e2/0x4b0
sock_recvmsg+0xde/0xf0
__sys_recvfrom+0x150/0x200
__x64_sys_recvfrom+0x76/0x90
do_syscall_64+0xc3/0x6e0
Allocated by task 1:
__kvmalloc_node_noprof+0x21b/0x700
nf_ct_alloc_hashtable+0x65/0xd0
nf_conntrack_helper_init+0x21/0x60
nf_conntrack_init_start+0x18d/0x300
nf_conntrack_standalone_init+0x12/0xc0
Fixes: 12f7a505331e ("netfilter: add user-space connection tracking helper infrastructure")
Signed-off-by: Hyunwoo Kim <imv4bel@gmail.com>
Signed-off-by: Florian Westphal <fw@strlen.de>
|
|
nfqnl_recv_verdict() calls find_dequeue_entry() to remove the queue
entry from the queue data structures, taking ownership of the entry.
For PF_BRIDGE packets, it then calls nfqa_parse_bridge() to parse VLAN
attributes. If nfqa_parse_bridge() returns an error (e.g. NFQA_VLAN
present but NFQA_VLAN_TCI missing), the function returns immediately
without freeing the dequeued entry or its sk_buff.
This leaks the nf_queue_entry, its associated sk_buff, and all held
references (net_device refcounts, struct net refcount). Repeated
triggering exhausts kernel memory.
Fix this by dropping the entry via nfqnl_reinject() with NF_DROP verdict
on the error path, consistent with other error handling in this file.
Fixes: 8d45ff22f1b4 ("netfilter: bridge: nf queue verdict to use NFQA_VLAN and NFQA_L2HDR")
Reviewed-by: David Dull <monderasdor@gmail.com>
Signed-off-by: Hyunwoo Kim <imv4bel@gmail.com>
Signed-off-by: Florian Westphal <fw@strlen.de>
|
|
When the last byte of options is a non-single-byte option kind, walkers
that advance with i += op[i + 1] ? : 1 can read op[i + 1] past the end
of the option area.
Add an explicit i == optlen - 1 check before dereferencing op[i + 1]
in xt_tcpudp and xt_dccp option walkers.
Fixes: 2e4e6a17af35 ("[NETFILTER] x_tables: Abstraction layer for {ip,ip6,arp}_tables")
Signed-off-by: David Dull <monderasdor@gmail.com>
Signed-off-by: Florian Westphal <fw@strlen.de>
|
|
pipapo_drop() passes rulemap[i + 1].n to pipapo_unmap() as the
to_offset argument on every iteration, including the last one where
i == m->field_count - 1. This reads one element past the end of the
stack-allocated rulemap array (declared as rulemap[NFT_PIPAPO_MAX_FIELDS]
with NFT_PIPAPO_MAX_FIELDS == 16).
Although pipapo_unmap() returns early when is_last is true without
using the to_offset value, the argument is evaluated at the call site
before the function body executes, making this a genuine out-of-bounds
stack read confirmed by KASAN:
BUG: KASAN: stack-out-of-bounds in pipapo_drop+0x50c/0x57c [nf_tables]
Read of size 4 at addr ffff8000810e71a4
This frame has 1 object:
[32, 160) 'rulemap'
The buggy address is at offset 164 -- exactly 4 bytes past the end
of the rulemap array.
Pass 0 instead of rulemap[i + 1].n on the last iteration to avoid
the out-of-bounds read.
Fixes: 3c4287f62044 ("nf_tables: Add set type for arbitrary concatenation of ranges")
Signed-off-by: Jenny Guanni Qu <qguanni@gmail.com>
Signed-off-by: Florian Westphal <fw@strlen.de>
|
|
During transaction processing we might have more than one catchall element:
1 live catchall element and 1 pending element that is coming as part of the
new batch.
If the map holding the catchall elements is also going away, its
required to toggle all catchall elements and not just the first viable
candidate.
Otherwise, we get:
WARNING: ./include/net/netfilter/nf_tables.h:1281 at nft_data_release+0xb7/0xe0 [nf_tables], CPU#2: nft/1404
RIP: 0010:nft_data_release+0xb7/0xe0 [nf_tables]
[..]
__nft_set_elem_destroy+0x106/0x380 [nf_tables]
nf_tables_abort_release+0x348/0x8d0 [nf_tables]
nf_tables_abort+0xcf2/0x3ac0 [nf_tables]
nfnetlink_rcv_batch+0x9c9/0x20e0 [..]
Fixes: 628bd3e49cba ("netfilter: nf_tables: drop map element references from preparation phase")
Reported-by: Yiming Qian <yimingqian591@gmail.com>
Signed-off-by: Florian Westphal <fw@strlen.de>
|
|
When handling NETDEV_REGISTER notification, duplicate device
registration must be avoided since the device may have been added by
nft_netdev_hook_alloc() already when creating the hook.
Suggested-by: Florian Westphal <fw@strlen.de>
Reported-by: syzbot+bb9127e278fa198e110c@syzkaller.appspotmail.com
Closes: https://syzkaller.appspot.com/bug?extid=bb9127e278fa198e110c
Fixes: a331b78a5525 ("netfilter: nf_tables: Respect NETDEV_REGISTER events")
Tested-by: Helen Koike <koike@igalia.com>
Signed-off-by: Phil Sutter <phil@nwl.cc>
Signed-off-by: Florian Westphal <fw@strlen.de>
|
|
Tunnel xmit functions (iptunnel_xmit, ip6tunnel_xmit) lack their own
recursion limit. When a bond device in broadcast mode has GRE tap
interfaces as slaves, and those GRE tunnels route back through the
bond, multicast/broadcast traffic triggers infinite recursion between
bond_xmit_broadcast() and ip_tunnel_xmit()/ip6_tnl_xmit(), causing
kernel stack overflow.
The existing XMIT_RECURSION_LIMIT (8) in the no-qdisc path is not
sufficient because tunnel recursion involves route lookups and full IP
output, consuming much more stack per level. Use a lower limit of 4
(IP_TUNNEL_RECURSION_LIMIT) to prevent overflow.
Add recursion detection using dev_xmit_recursion helpers directly in
iptunnel_xmit() and ip6tunnel_xmit() to cover all IPv4/IPv6 tunnel
paths including UDP encapsulated tunnels (VXLAN, Geneve, etc.).
Move dev_xmit_recursion helpers from net/core/dev.h to public header
include/linux/netdevice.h so they can be used by tunnel code.
BUG: KASAN: stack-out-of-bounds in blake2s.constprop.0+0xe7/0x160
Write of size 32 at addr ffff88810033fed0 by task kworker/0:1/11
Workqueue: mld mld_ifc_work
Call Trace:
<TASK>
__build_flow_key.constprop.0 (net/ipv4/route.c:515)
ip_rt_update_pmtu (net/ipv4/route.c:1073)
iptunnel_xmit (net/ipv4/ip_tunnel_core.c:84)
ip_tunnel_xmit (net/ipv4/ip_tunnel.c:847)
gre_tap_xmit (net/ipv4/ip_gre.c:779)
dev_hard_start_xmit (net/core/dev.c:3887)
sch_direct_xmit (net/sched/sch_generic.c:347)
__dev_queue_xmit (net/core/dev.c:4802)
bond_dev_queue_xmit (drivers/net/bonding/bond_main.c:312)
bond_xmit_broadcast (drivers/net/bonding/bond_main.c:5279)
bond_start_xmit (drivers/net/bonding/bond_main.c:5530)
dev_hard_start_xmit (net/core/dev.c:3887)
__dev_queue_xmit (net/core/dev.c:4841)
ip_finish_output2 (net/ipv4/ip_output.c:237)
ip_output (net/ipv4/ip_output.c:438)
iptunnel_xmit (net/ipv4/ip_tunnel_core.c:86)
gre_tap_xmit (net/ipv4/ip_gre.c:779)
dev_hard_start_xmit (net/core/dev.c:3887)
sch_direct_xmit (net/sched/sch_generic.c:347)
__dev_queue_xmit (net/core/dev.c:4802)
bond_dev_queue_xmit (drivers/net/bonding/bond_main.c:312)
bond_xmit_broadcast (drivers/net/bonding/bond_main.c:5279)
bond_start_xmit (drivers/net/bonding/bond_main.c:5530)
dev_hard_start_xmit (net/core/dev.c:3887)
__dev_queue_xmit (net/core/dev.c:4841)
ip_finish_output2 (net/ipv4/ip_output.c:237)
ip_output (net/ipv4/ip_output.c:438)
iptunnel_xmit (net/ipv4/ip_tunnel_core.c:86)
ip_tunnel_xmit (net/ipv4/ip_tunnel.c:847)
gre_tap_xmit (net/ipv4/ip_gre.c:779)
dev_hard_start_xmit (net/core/dev.c:3887)
sch_direct_xmit (net/sched/sch_generic.c:347)
__dev_queue_xmit (net/core/dev.c:4802)
bond_dev_queue_xmit (drivers/net/bonding/bond_main.c:312)
bond_xmit_broadcast (drivers/net/bonding/bond_main.c:5279)
bond_start_xmit (drivers/net/bonding/bond_main.c:5530)
dev_hard_start_xmit (net/core/dev.c:3887)
__dev_queue_xmit (net/core/dev.c:4841)
mld_sendpack
mld_ifc_work
process_one_work
worker_thread
</TASK>
Fixes: 745e20f1b626 ("net: add a recursion limit in xmit path")
Reported-by: Xiang Mei <xmei5@asu.edu>
Signed-off-by: Weiming Shi <bestswngs@gmail.com>
Link: https://patch.msgid.link/20260306160133.3852900-2-bestswngs@gmail.com
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
|
|
Raju Rangoju says:
====================
amd-xgbe: RX adaptation and PHY handling fixes
This series fixes several issues in the amd-xgbe driver related to RX
adaptation and PHY handling in 10GBASE-KR mode, particularly when
auto-negotiation is disabled.
Patch 1 fixes link status handling during RX adaptation by correctly
reading the latched link status bit so transient link drops are
detected without losing the current state.
Patch 2 prevents CRC errors that can occur when performing RX
adaptation with auto-negotiation turned off. The driver now stops
TX/RX before re-triggering RX adaptation and only re-enables traffic
once adaptation completes and the link is confirmed up, ensuring
packets are not corrupted during the adaptation window.
Patch 3 restores the intended ordering of PHY reset relative to
phy_start(), making sure PHY settings are reset before the PHY is
started instead of afterwards.
====================
Link: https://patch.msgid.link/20260306111629.1515676-1-Raju.Rangoju@amd.com
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
|
|
commit f93505f35745 ("amd-xgbe: let the MAC manage PHY PM") moved
xgbe_phy_reset() from xgbe_open() to xgbe_start(), placing it after
phy_start(). As a result, the PHY settings were being reset after the
PHY had already started.
Reorder the calls so that the PHY settings are reset before
phy_start() is invoked.
Fixes: f93505f35745 ("amd-xgbe: let the MAC manage PHY PM")
Reviewed-by: Maxime Chevallier <maxime.chevallier@bootlin.com>
Signed-off-by: Raju Rangoju <Raju.Rangoju@amd.com>
Link: https://patch.msgid.link/20260306111629.1515676-4-Raju.Rangoju@amd.com
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
|
|
When operating in 10GBASE-KR mode with auto-negotiation disabled and RX
adaptation enabled, CRC errors can occur during the RX adaptation
process. This happens because the driver continues transmitting and
receiving packets while adaptation is in progress.
Fix this by stopping TX/RX immediately when the link goes down and RX
adaptation needs to be re-triggered, and only re-enabling TX/RX after
adaptation completes and the link is confirmed up. Introduce a flag to
track whether TX/RX was disabled for adaptation so it can be restored
correctly.
This prevents packets from being transmitted or received during the RX
adaptation window and avoids CRC errors from corrupted frames.
The flag tracking the data path state is synchronized with hardware
state in xgbe_start() to prevent stale state after device restarts.
This ensures that after a restart cycle (where xgbe_stop disables
TX/RX and xgbe_start re-enables them), the flag correctly reflects
that the data path is active.
Fixes: 4f3b20bfbb75 ("amd-xgbe: add support for rx-adaptation")
Signed-off-by: Raju Rangoju <Raju.Rangoju@amd.com>
Link: https://patch.msgid.link/20260306111629.1515676-3-Raju.Rangoju@amd.com
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
|
|
The link status bit is latched low to allow detection of momentary
link drops. If the status indicates that the link is already down,
read it again to obtain the current state.
Fixes: 4f3b20bfbb75 ("amd-xgbe: add support for rx-adaptation")
Signed-off-by: Raju Rangoju <Raju.Rangoju@amd.com>
Link: https://patch.msgid.link/20260306111629.1515676-2-Raju.Rangoju@amd.com
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
|
|
mctp_flow_prepare_output() checks key->dev and may call
mctp_dev_set_key(), but it does not hold key->lock while doing so.
mctp_dev_set_key() and mctp_dev_release_key() are annotated with
__must_hold(&key->lock), so key->dev access is intended to be
serialized by key->lock. The mctp_sendmsg() transmit path reaches
mctp_flow_prepare_output() via mctp_local_output() -> mctp_dst_output()
without holding key->lock, so the check-and-set sequence is racy.
Example interleaving:
CPU0 CPU1
---- ----
mctp_flow_prepare_output(key, devA)
if (!key->dev) // sees NULL
mctp_flow_prepare_output(
key, devB)
if (!key->dev) // still NULL
mctp_dev_set_key(devB, key)
mctp_dev_hold(devB)
key->dev = devB
mctp_dev_set_key(devA, key)
mctp_dev_hold(devA)
key->dev = devA // overwrites devB
Now both devA and devB references were acquired, but only the final
key->dev value is tracked for release. One reference can be lost,
causing a resource leak as mctp_dev_release_key() would only decrease
the reference on one dev.
Fix by taking key->lock around the key->dev check and
mctp_dev_set_key() call.
Fixes: 67737c457281 ("mctp: Pass flow data & flow release events to drivers")
Signed-off-by: Chengfeng Ye <dg573847474@gmail.com>
Link: https://patch.msgid.link/20260306031402.857224-1-dg573847474@gmail.com
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
|
|
kernel BUG at net/core/skbuff.c:2306!
Oops: invalid opcode: 0000 [#1] SMP KASAN NOPTI
RIP: 0010:pskb_expand_head+0xa08/0xfe0 net/core/skbuff.c:2306
RSP: 0018:ffffc90004aff760 EFLAGS: 00010293
RAX: 0000000000000000 RBX: ffff88807e3c8780 RCX: ffffffff89593e0e
RDX: ffff88807b7c4900 RSI: ffffffff89594747 RDI: ffff88807b7c4900
RBP: 0000000000000820 R08: 0000000000000005 R09: 0000000000000000
R10: 00000000961a63e0 R11: 0000000000000000 R12: ffff88807e3c8780
R13: 00000000961a6560 R14: dffffc0000000000 R15: 00000000961a63e0
CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033
CR2: 00007fe1a0ed8df0 CR3: 000000002d816000 CR4: 00000000003526f0
Call Trace:
<TASK>
ipgre_header+0xdd/0x540 net/ipv4/ip_gre.c:900
dev_hard_header include/linux/netdevice.h:3439 [inline]
packet_snd net/packet/af_packet.c:3028 [inline]
packet_sendmsg+0x3ae5/0x53c0 net/packet/af_packet.c:3108
sock_sendmsg_nosec net/socket.c:727 [inline]
__sock_sendmsg net/socket.c:742 [inline]
____sys_sendmsg+0xa54/0xc30 net/socket.c:2592
___sys_sendmsg+0x190/0x1e0 net/socket.c:2646
__sys_sendmsg+0x170/0x220 net/socket.c:2678
do_syscall_x64 arch/x86/entry/syscall_64.c:63 [inline]
do_syscall_64+0x106/0xf80 arch/x86/entry/syscall_64.c:94
entry_SYSCALL_64_after_hwframe+0x77/0x7f
RIP: 0033:0x7fe1a0e6c1a9
When a non-Ethernet device (e.g. GRE tunnel) is enslaved to a bond,
bond_setup_by_slave() directly copies the slave's header_ops to the
bond device:
bond_dev->header_ops = slave_dev->header_ops;
This causes a type confusion when dev_hard_header() is later called
on the bond device. Functions like ipgre_header(), ip6gre_header(),all use
netdev_priv(dev) to access their device-specific private data. When
called with the bond device, netdev_priv() returns the bond's private
data (struct bonding) instead of the expected type (e.g. struct
ip_tunnel), leading to garbage values being read and kernel crashes.
Fix this by introducing bond_header_ops with wrapper functions that
delegate to the active slave's header_ops using the slave's own
device. This ensures netdev_priv() in the slave's header functions
always receives the correct device.
The fix is placed in the bonding driver rather than individual device
drivers, as the root cause is bond blindly inheriting header_ops from
the slave without considering that these callbacks expect a specific
netdev_priv() layout.
The type confusion can be observed by adding a printk in
ipgre_header() and running the following commands:
ip link add dummy0 type dummy
ip addr add 10.0.0.1/24 dev dummy0
ip link set dummy0 up
ip link add gre1 type gre local 10.0.0.1
ip link add bond1 type bond mode active-backup
ip link set gre1 master bond1
ip link set gre1 up
ip link set bond1 up
ip addr add fe80::1/64 dev bond1
Fixes: 1284cd3a2b74 ("bonding: two small fixes for IPoIB support")
Suggested-by: Jay Vosburgh <jv@jvosburgh.net>
Reviewed-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: Jiayuan Chen <jiayuan.chen@shopee.com>
Link: https://patch.msgid.link/20260306021508.222062-1-jiayuan.chen@linux.dev
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
|
|
In hi3110_open(), the return value of hi3110_power_enable() is not checked.
If power enable fails, the device may not function correctly, while the
driver still returns success.
Add a check for the return value and propagate the error accordingly.
Signed-off-by: Wenyuan Li <2063309626@qq.com>
Link: https://patch.msgid.link/tencent_B5E2E7528BB28AA8A2A56E16C49BD58B8B07@qq.com
Fixes: 57e83fb9b746 ("can: hi311x: Add Holt HI-311x CAN driver")
[mkl: adjust subject, commit message and jump label]
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
|
|
Commit b360a13d44db ("can: dev: print bitrate error with two decimal
digits") changed calculation of the bit rate error from on-tenth of a
percent to on-hundredth of a percent, but forgot to adjust the scale of the
CAN_CALC_MAX_ERROR constant.
Keeping the existing logic unchanged: Only when the bitrate error exceeds
5% should an error be returned. Otherwise, simply output a warning log.
Fixes: b360a13d44db ("can: dev: print bitrate error with two decimal digits")
Signed-off-by: Haibo Chen <haibo.chen@nxp.com>
Link: https://patch.msgid.link/20260306-can-fix-v1-1-ac526cec6777@nxp.com
Cc: stable@kernel.org
[mkl: improve commit message]
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
|
|
When 'midev->allow_rx' is false, the newly allocated skb isn't consumed
by netif_rx(), it needs to free the skb directly.
Fixes: f5b8abf9fc3d ("mctp i2c: MCTP I2C binding driver")
Signed-off-by: Haiyue Wang <haiyuewa@163.com>
Link: https://patch.msgid.link/20260305143240.97592-1-haiyuewa@163.com
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
|
|
obj_exts_alloc_size() prevents recursive allocation of slabobj_ext
array from the same cache, to avoid creating slabs that are never freed.
There is one mistake that returns the original size when memory
allocation profiling is disabled. The assumption was that
memcg-triggered slabobj_ext allocation is always served from
KMALLOC_CGROUP type. But this is wrong [1]: when the caller specifies
both __GFP_RECLAIMABLE and __GFP_ACCOUNT with SLUB_TINY enabled, the
allocation is served from normal kmalloc. This is because kmalloc_type()
prioritizes __GFP_RECLAIMABLE over __GFP_ACCOUNT, and SLUB_TINY aliases
KMALLOC_RECLAIM with KMALLOC_NORMAL.
As a result, the recursion guard is bypassed and the problematic slabs
can be created. Fix this by removing the mem_alloc_profiling_enabled()
check entirely. The remaining is_kmalloc_normal() check is still
sufficient to detect whether the cache is of KMALLOC_NORMAL type and
avoid bumping the size if it's not.
Without SLUB_TINY, no functional change intended.
With SLUB_TINY, allocations with __GFP_ACCOUNT|__GFP_RECLAIMABLE
now allocate a larger array if the sizes equal.
Reported-by: Zw Tang <shicenci@gmail.com>
Fixes: 280ea9c3154b ("mm/slab: avoid allocating slabobj_ext array from its own slab")
Closes: https://lore.kernel.org/linux-mm/CAPHJ_VKuMKSke8b11AZQw1PTSFN4n2C0gFxC6xGOG0ZLHgPmnA@mail.gmail.com [1]
Cc: stable@vger.kernel.org
Signed-off-by: Harry Yoo <harry.yoo@oracle.com>
Link: https://patch.msgid.link/20260309072219.22653-1-harry.yoo@oracle.com
Tested-by: Zw Tang <shicenci@gmail.com>
Signed-off-by: Vlastimil Babka (SUSE) <vbabka@kernel.org>
|
|
'net-enetc-fix-fallback-phy-address-handling-and-do-not-skip-setting-for-addr-0'
Wei Fang says:
====================
net: enetc: fix fallback PHY address handling and do not skip setting for addr 0
There are two potential issues when PHY address 0 is used on the board,
see the commit messages of the patches for more details.
v1: https://lore.kernel.org/imx/20260303103047.228005-1-wei.fang@nxp.com/
====================
Link: https://patch.msgid.link/20260305031211.904812-1-wei.fang@nxp.com
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
|
|
Given that some platforms may use PHY address 0 (I suppose the PHY may
not treat address 0 as a broadcast address or default response address).
It is possible for some boards to connect multiple PHYs to the same
ENETC MAC, for example:
- a PHY with a non-zero address connects to ENETC MAC through SGMII
interface (selected via DTS_A)
- a PHY with address 0 connects to ENETC MAC through RGMII interface
(selected via DTS_B)
For the case where the ENETC port MDIO is used to manage the PHY, when
switching from DTS_A to DTS_B via soft reboot, LaBCR[MDIO_PHYAD_PRTAD]
must be updated to 0 because the NETCMIX block is not reset during soft
reboot. However, the current driver explicitly skips configuring address
0, causing LaBCR[MDIO_PHYAD_PRTAD] to retain its old value.
Therefore, remove the special-case skip of PHY address 0 so that valid
configurations using address 0 are properly supported.
Fixes: 6633df05f3ad ("net: enetc: set the external PHY address in IERB for port MDIO usage")
Fixes: 50bfd9c06f0f ("net: enetc: set external PHY address in IERB for i.MX94 ENETC")
Reviewed-by: Clark Wang <xiaoning.wang@nxp.com>
Signed-off-by: Wei Fang <wei.fang@nxp.com>
Link: https://patch.msgid.link/20260305031211.904812-3-wei.fang@nxp.com
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
|
|
The current netc_get_phy_addr() implementation falls back to PHY address
0 when the "mdio" node or the PHY child node is missing. On i.MX95, this
causes failures when a real PHY is actually assigned address 0 and is
managed through the EMDIO interface. Because the bit 0 of phy_mask will
be set, leading imx95_enetc_mdio_phyaddr_config() to return an error, and
the netc_blk_ctrl driver probe subsequently fails. Fix this by returning
-ENODEV when neither an "mdio" node nor any PHY node is present, it means
that ENETC port MDIO is not used to manage the PHY, so there is no need
to configure LaBCR[MDIO_PHYAD_PRTAD].
Reported-by: Alexander Stein <alexander.stein@ew.tq-group.com>
Closes: https://lore.kernel.org/all/7825188.GXAFRqVoOG@steina-w
Fixes: 6633df05f3ad ("net: enetc: set the external PHY address in IERB for port MDIO usage")
Reviewed-by: Clark Wang <xiaoning.wang@nxp.com>
Tested-by: Alexander Stein <alexander.stein@ew.tq-group.com>
Signed-off-by: Wei Fang <wei.fang@nxp.com>
Link: https://patch.msgid.link/20260305031211.904812-2-wei.fang@nxp.com
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
|
|
The Scarlett2 mixer quirk in USB-audio driver may hit a NULL
dereference when a malformed USB descriptor is passed, since it
assumes the presence of an endpoint in the parsed interface in
scarlett2_find_fc_interface(), as reported by fuzzer.
For avoiding the NULL dereference, just add the sanity check of
bNumEndpoints and skip the invalid interface.
Reported-by: syzbot+8f29539ef9a1c8334f42@syzkaller.appspotmail.com
Closes: https://lore.kernel.org/69acbbe1.050a0220.310d8.0001.GAE@google.com
Reported-by: syzbot+ae893a8901067fde2741@syzkaller.appspotmail.com
Closes: https://lore.kernel.org/69acf72a.050a0220.310d8.0004.GAE@google.com
Cc: <stable@vger.kernel.org>
Link: https://patch.msgid.link/20260309104632.141895-1-tiwai@suse.de
Signed-off-by: Takashi Iwai <tiwai@suse.de>
|
|
When changing channels, the current check in bnxt_set_channels()
is not checking for non-default RSS contexts when the RSS table size
changes. The current check for IFF_RXFH_CONFIGURED is only sufficient
for the default RSS context. Expand the check to include the presence
of any non-default RSS contexts.
Allowing such change will result in incorrect configuration of the
context's RSS table when the table size changes.
Fixes: b3d0083caf9a ("bnxt_en: Support RSS contexts in ethtool .{get|set}_rxfh()")
Reported-by: Björn Töpel <bjorn@kernel.org>
Link: https://lore.kernel.org/netdev/20260303181535.2671734-1-bjorn@kernel.org/
Reviewed-by: Andy Gospodarek <andrew.gospodarek@broadcom.com>
Signed-off-by: Pavan Chebbi <pavan.chebbi@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Link: https://patch.msgid.link/20260306225854.3575672-1-michael.chan@broadcom.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
