| Age | Commit message (Collapse) | Author |
|---|
|
Since hub usb2517 is going to be supported by the usb251xb driver,
the bindings need to be properly updated. Particularly:
- add "microchip,usb2517" and "microchip,usb2517i" compatible strings.
- add "boolean" description to all the properties, which really accept
a boolean value including a new one "led-{usb,speed}-mode".
- move reset-gpios property to the optional section. It isn't
defined as required in the code and shouldn't be required at all, since
hardware may handle reset pins by itself.
- add new led-{usb,speed}-mode mode property. USB2517 device supports
two LED modes: USB mode and speed (default) indication mode. The last one
can be switched on by this property.
- add {bp,sp}-max-{total,removable}-current-microamp property measured in
microamp. It hasn't been defined as property before. Since the limitation
specified by these parameters is hardware specific it needs to be defined
in dts.
Signed-off-by: Serge Semin <fancer.lancer@gmail.com>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Documentation modification, now interrupt-parent is an optional
property. Also fix few typos.
Signed-off-by: Jules Maselbas <jules.maselbas@grenoble-inp.org>
Reported-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/kishon/linux-phy into usb-next
Kishon writes:
phy: for 4.15
*) Add support in phy core to perform phy calibration
*) Return NULL for optional PHY's even if CONFIG_GENERIC_PHY is not selected
*) Add USB Phy driver for Broadcom STB SoCs
*) Add support to force mediatek PHY with USB OTG function to enter
a specific mode
*) Calibrate rockchip-typec PHY according to docs
*) Enable dual route feature for sun4i-usb in V3s SoC
*) Use dr_mode dt property to enable otg capability in rcar-gen3-usb2
*) Add driver data to specify dedicated otg pins in rcar-gen3-usb2 driver
*) Configure the RX equalizer of brcm-sata PHY
*) Update pcie phy settings for ti-pipe3 phy
*) Add set_mode callback in qcom-ufs-qmp-14nm phy
*) Use PHY callbacks in phy-qcom-ufs instead of export APIs
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/balbi/usb into usb-next
Felipe writes:
usb: changes for v4.15 merge window
Not much going on this time around. With only 51 non-merge commits,
this was one of the smallest pull requests from the Gadget tree.
Most of the changes are in the mtu3 driver which added support for
36-bit DMA, support for USB 3.1 and support for dual-role (along with
some non-critical fixes).
The dwc2 driver got a few improvements to how we handle gadget state
tracking and also added support for STM32F7xx devices.
Other than that, we just some minor non-critical fixes and
improvements all over the place.
|
|
We need the USB fixes in here as well.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/staging
Pull staging and IIO fixes from Greg KH:
"Here are a small number of patches to resolve some reported IIO and a
staging driver problem. Nothing major here, full details are in the
shortlog below.
All have been in linux-next with no reported issues"
* tag 'staging-4.14-rc6' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/staging:
staging: bcm2835-audio: Fix memory corruption
iio: adc: at91-sama5d2_adc: fix probe error on missing trigger property
iio: adc: dln2-adc: fix build error
iio: dummy: events: Add missing break
staging: iio: ade7759: fix signed extension bug on shift of a u8
iio: pressure: zpa2326: Remove always-true check which confuses gcc
iio: proximity: as3935: noise detection + threshold changes
|
|
Remove dummy clocks for usb wakeup and add optional ones for
MCU_BUS_CK and DMA_BUS_CK.
Signed-off-by: Chunfeng Yun <chunfeng.yun@mediatek.com>
Acked-by: Rob Herring <robh@kernel.org>
Reviewed-by: Matthias Brugger <matthias.bgg@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Add a new optional property to disable u3ports
Signed-off-by: Chunfeng Yun <chunfeng.yun@mediatek.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Define two new properties: brcm,rx-aeq-mode which allows configuring the
SATA PHY RX equalizers and when "manual" is used, brcm,rx-aeq can be
used to set the exact value.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
|
|
This patch adds binding for r8a77995 (R-Car D3). Since r8a77995 doesn't
have dedicated pins (ID, VBUS), this will match against the generic
fallback on R-Car D3.
For now, this driver doesn't support usb role swap for r8a77995.
Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Reviewed-by: Simon Horman <horms+renesas@verge.net.au>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
|
|
Add USB PHY support for r8a7743/5 SoC. Renesas RZ/G1[ME] (R8A7743/5)
USB PHY is identical to the R-Car Gen2 family.
Signed-off-by: Biju Das <biju.das@bp.renesas.com>
Acked-by: Simon Horman <horms+renesas@verge.net.au>
Acked-by: Rob Herring <robh@kernel.org>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
|
|
This patch adds support for r8a7743/5 SoCs. The Renesas RZ/G1[ME]
(R8A7743/5) usbhs is identical to the R-Car Gen2 family.
No driver change is needed due to the fallback compatible value
"renesas,rcar-gen2-usbhs".
Adding the SoC-specific compatible values here has two purposes:
1. Document which SoCs have this hardware module,
2. Allow checkpatch to validate compatible values.
Acked-by: Rob Herring <robh@kernel.org>
Acked-by: Simon Horman <horms+renesas@verge.net.au>
Signed-off-by: Biju Das <biju.das@bp.renesas.com>
Signed-off-by: Chris Paterson <chris.paterson2@renesas.com>
Reviewed-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
|
|
Remove optional pinctrls due to using FORCE/RG_IDDIG to implement
manual switch function.
Signed-off-by: Chunfeng Yun <chunfeng.yun@mediatek.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
|
|
Remove dummy clocks for usb wakeup and add optional ones for
mcu_bus and dma_bus bus.
Signed-off-by: Chunfeng Yun <chunfeng.yun@mediatek.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
|
|
Add a new optional property to disable u3ports
Signed-off-by: Chunfeng Yun <chunfeng.yun@mediatek.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
|
|
This patch adds binding documentation for DWC2 controller in HS mode found
on STMicroelectronics STM32F7xx SoC.
Signed-off-by: Amelie Delaunay <amelie.delaunay@st.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
|
|
This patch adds support for generic phy as an optional. If you want
to use a generic phy (e.g. phy-rcar-gen3-usb3 driver) on this driver,
you have to do "insmod phy-rcar-gen3-usb3.ko" first for now.
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
|
|
This patch adds support for R-Car D3. This SoC needs to release
the PLL reset by the UGCTRL register. So, since this is not the same
as other R-Car Gen3 SoCs, this patch adds a new type as
"USBHS_TYPE_RCAR_GEN3_WITH_PLL".
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/maz/arm-platforms into irq/urgent
Pull irqchip updates for 4.14-rc5 from Marc Zyngier:
- Fix unfortunate mistake in the GICv3 ITS binding example
- Two fixes for the recently merged GICv4 support
- GICv3 ITS 52bit PA fixes
- Generic irqchip mask-ack fix, and its application to the tango irqchip
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/jic23/iio into staging-linus
Jonathan writes:
Second set of IIO fixes for the 4.14 cycle.
* ade7759
- Fix a signed extension bug.
* as3935
- The default noise and watch dog settings were such that the device
was unusuable in most applications. Add device tree parameters to
allow it to be configured to something that will actually work.
* at91-sama5d2 adc
- Fix handling of legacy device trees that don't provide the new
trigger edge property.
* dln2-adc
- Fix a missing Kconfig dependency on IIO_TRIGGERED_BUFFER.
* dummy driver
- Add a missing break so that writing in_voltage0_thresh_rising_en
doesn't always result in an error.
* zpa2326
- Drop a test for an always true condition so that gcc won't spit out
and unused variable warning.
|
|
Currently, the examples are using 2MB for the ITS size. Per the
specification (section 8.18 in ARM IHI 0069D), the ITS address map is
128KB.
Update the examples to match the specification.
Signed-off-by: Julien Grall <julien.grall@linaro.org>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
|
|
This merges in the USB fixes that we need here.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/ulfh/mmc
Pull MMC fixes from Ulf Hansson:
"MMC core:
- Fix driver strength selection when selecting hs400es
- Delete bounce buffer handling:
This change fixes a problem related to how bounce buffers are being
allocated. However, instead of trying to fix that, let's just
remove the mmc bounce buffer code altogether, as it has practically
no use.
MMC host:
- meson-gx: A couple of fixes related to clock/phase/tuning
- sdhci-xenon: Fix clock resource by adding an optional bus clock"
* tag 'mmc-v4.14-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/ulfh/mmc:
mmc: sdhci-xenon: Fix clock resource by adding an optional bus clock
mmc: meson-gx: include tx phase in the tuning process
mmc: meson-gx: fix rx phase reset
mmc: meson-gx: make sure the clock is rounded down
mmc: Delete bounce buffer handling
mmc: core: add driver strength selection when selecting hs400es
|
|
Pull networking fixes from David Miller:
1) Check iwlwifi 9000 reorder buffer out-of-space condition properly,
from Sara Sharon.
2) Fix RCU splat in qualcomm rmnet driver, from Subash Abhinov
Kasiviswanathan.
3) Fix session and tunnel release races in l2tp, from Guillaume Nault
and Sabrina Dubroca.
4) Fix endian bug in sctp_diag_dump(), from Dan Carpenter.
5) Several mlx5 driver fixes from the Mellanox folks (max flow counters
cap check, invalid memory access in IPoIB support, etc.)
6) tun_get_user() should bail if skb->len is zero, from Alexander
Potapenko.
7) Fix RCU lookups in inetpeer, from Eric Dumazet.
8) Fix locking in packet_do_bund().
9) Handle cb->start() error properly in netlink dump code, from Jason
A. Donenfeld.
10) Handle multicast properly in UDP socket early demux code. From Paolo
Abeni.
11) Several erspan bug fixes in ip_gre, from Xin Long.
12) Fix use-after-free in socket filter code, in order to handle the
fact that listener lock is no longer taken during the three-way TCP
handshake. From Eric Dumazet.
13) Fix infoleak in RTM_GETSTATS, from Nikolay Aleksandrov.
14) Fix tail call generation in x86-64 BPF JIT, from Alexei Starovoitov.
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net: (77 commits)
net: 8021q: skip packets if the vlan is down
bpf: fix bpf_tail_call() x64 JIT
net: stmmac: dwmac-rk: Add RK3128 GMAC support
rndis_host: support Novatel Verizon USB730L
net: rtnetlink: fix info leak in RTM_GETSTATS call
socket, bpf: fix possible use after free
mlxsw: spectrum_router: Track RIF of IPIP next hops
mlxsw: spectrum_router: Move VRF refcounting
net: hns3: Fix an error handling path in 'hclge_rss_init_hw()'
net: mvpp2: Fix clock resource by adding an optional bus clock
r8152: add Linksys USB3GIGV1 id
l2tp: fix l2tp_eth module loading
ip_gre: erspan device should keep dst
ip_gre: set tunnel hlen properly in erspan_tunnel_init
ip_gre: check packet length and mtu correctly in erspan_xmit
ip_gre: get key from session_id correctly in erspan_rcv
tipc: use only positive error codes in messages
ppp: fix __percpu annotation
udp: perform source validation for mcast early demux
IPv4: early demux can return an error code
...
|
|
XHCI specification 1.1 does not require xHCI-compliant controllers
to always enable hardware USB2 LPM. However, the current xHCI
driver always enable it when seeing HLC=1.
This patch supports an option for users to control disabling
USB2 Hardware LPM via DT/ACPI attribute.
This option is needed in case user would like to disable this
feature. For example, their xHCI controller has its USB2 HW LPM
broken.
Signed-off-by: Tung Nguyen <tunguyen@apm.com>
Signed-off-by: Thang Q. Nguyen <tqnguyen@apm.com>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM SoC fixes from Olof Johansson:
"Our first batch of fixes this release cycle, unfortunately a bit
noisier than usual. Two major groups stand out:
- Some pinctril dts/dtsi changes for stm32 due to a new driver being
merged during the merge window, and this aligns the DT contents
between the old format and the new. This could arguably be moved to
the next merge window but it also seemed relatively harmless to
include now.
- Amlogic/meson had driver changes merged that required devicetree
changes to avoid functional/performance regressions. I've already
asked them to be more careful about this going forward, and making
sure drivers are compatible with older DTs when they make these
kind of changes. The platform is actively being upstreamed so
there's a few things in flight, we've seen this happen before and
sometimes it's hard to catch in time.
Besides that there is the usual mix of minor fixes"
* tag 'armsoc-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (33 commits)
ARM: dts: stm32: use right pinctrl compatible for stm32f469
ARM: dts: stm32: Fix STMPE1600 binding on stm32429i-eval board
ARM: defconfig: update Gemini defconfig
ARM: defconfig: FRAMEBUFFER_CONSOLE can no longer be =m
arm64: dts: rockchip: add the grf clk for dw-mipi-dsi on rk3399
reset: Restrict RESET_HSDK to ARC_SOC_HSDK or COMPILE_TEST
ARM: dts: da850-evm: add serial and ethernet aliases
ARM: dts: am43xx-epos-evm: Remove extra CPSW EMAC entry
ARM: dts: am33xx: Add spi alias to match SOC schematics
ARM: OMAP2+: hsmmc: fix logic to call either omap_hsmmc_init or omap_hsmmc_late_init but not both
ARM: dts: dra7: Set a default parent to mcasp3_ahclkx_mux
ARM: OMAP2+: dra7xx: Set OPT_CLKS_IN_RESET flag for gpio1
ARM: dts: nokia n900: drop unneeded/undocumented parts of the dts
arm64: dts: rockchip: Correct MIPI DPHY PLL clock on rk3399
arm64: dt marvell: Fix AP806 system controller size
MAINTAINERS: add Macchiatobin maintainers entry
ARC: reset: remove the misleading v1 suffix all over
ARC: reset: add missing DT binding documentation for HSDKv1 reset driver
ARC: reset: Only build on archs that have IOMEM
ARM: at91: Replace uses of virt_to_phys with __pa_symbol
...
|
|
On Armada 7K/8K we need to explicitly enable the bus clock. The bus clock
is optional because not all the SoCs need them but at least for Armada
7K/8K it is actually mandatory.
The binding documentation is updating accordingly.
Without this patch the kernel hand during boot if the mvpp2.2 network
driver was not present in the kernel. Indeed the clock needed by the
xenon controller was set by the network driver.
Fixes: 3a3748dba881 ("mmc: sdhci-xenon: Add Marvell Xenon SDHC core
functionality)"
CC: Stable <stable@vger.kernel.org>
Tested-by: Zhoujie Wu <zjwu@marvell.com>
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
|
|
Adds bindings documentation for the max3421 driver.
Signed-off-by: Jules Maselbas <jules.maselbas@grenoble-inp.org>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
into fixes
Reset controller fixes for v4.14
- Remove misleading HSDK v1 suffix, as there is no v2 planned
- Add missing DT binding documentation for HSDK reset driver
- Fix HSDK reset driver dependencies
* tag 'reset-fixes-for-4.14' of git://git.pengutronix.de/git/pza/linux:
reset: Restrict RESET_HSDK to ARC_SOC_HSDK or COMPILE_TEST
ARC: reset: remove the misleading v1 suffix all over
ARC: reset: add missing DT binding documentation for HSDKv1 reset driver
ARC: reset: Only build on archs that have IOMEM
Signed-off-by: Olof Johansson <olof@lixom.net>
|
|
Add constants and callback functions for the dwmac on rk3128 soc.
As can be seen, the base structure is the same, only registers
and the bits in them moved slightly.
Signed-off-by: David Wu <david.wu@rock-chips.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty
Pull tty/serial fixes from Greg KH:
"Here are a small number (5) of patches for some reported TTY and
serial issues. Nothing major, a documentation update, timing fix,
error handling fix, name reporting fix, and a timeout issue resolved.
All of these have been in linux-next for a while with no reported
issues"
* tag 'tty-4.14-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty:
serial: sccnxp: Fix error handling in sccnxp_probe()
tty: serial: lpuart: avoid report NULL interrupt
serial: bcm63xx: fix timing issue.
mxser: fix timeout calculation for low rates
serial: sh-sci: document R8A77970 bindings
|
|
Add DT bindings document for Broadcom STB USB PHYs
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Al Cooper <alcooperx@gmail.com>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
|
|
On Armada 7K/8K we need to explicitly enable the bus clock. The bus clock
is optional because not all the SoCs need them but at least for Armada
7K/8K it is actually mandatory.
The binding documentation is updating accordingly.
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/j.anaszewski/linux-leds
Pull LED fixes from Jacek Anaszewski:
"Four fixes for the as3645a LED flash controller and one update to
MAINTAINERS"
* tag 'led_fixes-4.14-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/j.anaszewski/linux-leds:
MAINTAINERS: Add entry for MediaTek PMIC LED driver
as3645a: Unregister indicator LED on device unbind
as3645a: Use integer numbers for parsing LEDs
dt: bindings: as3645a: Use LED number to refer to LEDs
as3645a: Use ams,input-max-microamp as documented in DT bindings
|
|
Most applications are too noisy to allow the default noise and
watchdog settings, and thus need to be configurable via DT
properties.
Also default settings to POR defaults on a reset, and register
distuber interrupts as noise since it prevents proper usage.
Cc: devicetree@vger.kernel.org
Signed-off-by: Matt Ranostay <matt.ranostay@konsulko.com>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/robh/linux
Pull DeviceTree fixes from Rob Herring:
- fix build for !OF providing empty of_find_device_by_node
- fix Abracon vendor prefix
- sync dtx_diff include paths (again)
- a stm32h7 clock binding doc fix
* tag 'devicetree-fixes-for-4.14' of git://git.kernel.org/pub/scm/linux/kernel/git/robh/linux:
dt-bindings: clk: stm32h7: fix clock-cell size
scripts/dtc: dtx_diff - 2nd update of include dts paths to match build
dt-bindings: fix vendor prefix for Abracon
of: provide inline helper for of_find_device_by_node
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/jmorris/linux-security
Pull TPM updates from James Morris:
"Here are the TPM updates from Jarkko for v4.14, which I've placed in
their own branch (next-tpm). I ended up cherry-picking them as other
changes had been made in Jarkko's branch after he sent me his original
pull request.
I plan on maintaining a separate branch for TPM (and other security
subsystems) from now on.
From Jarkko: 'Not much this time except a few fixes'"
* 'next-tpm' of git://git.kernel.org/pub/scm/linux/kernel/git/jmorris/linux-security:
tpm: ibmvtpm: simplify crq initialization and document crq format
tpm: replace msleep() with usleep_range() in TPM 1.2/2.0 generic drivers
Documentation: tpm: add powered-while-suspended binding documentation
tpm: tpm_crb: constify acpi_device_id.
tpm: vtpm: constify vio_device_id
|
|
Add a new powered-while-suspended property to control the behavior of the
TPM suspend/resume.
Signed-off-by: Enric Balletbo i Serra <enric.balletbo@collabora.com>
Signed-off-by: Sonny Rao <sonnyrao@chromium.org>
Reviewed-by: Jason Gunthorpe <jgunthorpe@obsidianresearch.com>
Reviewed-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
Signed-off-by: James Morris <james.l.morris@oracle.com>
|
|
Use integers (reg property) to tell the number of the LED to the driver
instead of the node name. While both of these approaches are currently
used by the LED bindings, using integers will require less driver changes
for ACPI support. Additionally, it will make possible LED naming using
chip and LED node names, effectively making the label property most useful
for human-readable names only.
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Jacek Anaszewski <jacek.anaszewski@gmail.com>
|
|
The clock-cell size is 1 on stm32h7 plaform.
Signed-off-by: Gabriel Fernandez <gabriel.fernandez@st.com>
Fixes: 3e4d618b0722 ("clk: stm32h7: Add stm32h743 clock driver")
Signed-off-by: Rob Herring <robh@kernel.org>
|
|
Commit 446810f2dd41 ("of: add vendor prefix for Abracon Corporation")
claimed that "abcn" was used as the vendor prefix while in fact "abracon"
was used in the subsequent commits. It is also the only prefix used in the
tree.
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
[robh: fix alphabetical order]
Signed-off-by: Rob Herring <robh@kernel.org>
|
|
R-Car V3M (R8A77970) SoC also has the R-Car gen3 compatible SCIF and HSCIF
ports, so document the SoC specific bindings.
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Acked-by: Rob Herring <robh@kernel.org>
Acked-by: Geert Uytterhoeven <geert+renesas@glider.be>
Acked-by: Simon Horman <horms+renesas@verge.net.au>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
There is no plan yet to do a v2 board. And even if we were to do it only
some IPs would actually change, so it be best to add suffixes at that
point, not now !
Signed-off-by: Vineet Gupta <vgupta@synopsys.com>
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
|
|
When applying the original patch [1], the DT binding docs were lost.
This patch adds them back.
[1] https://patchwork.kernel.org/patch/9852997/
Fixes: e0be864f1424 ("ARC: reset: introduce HSDKv1 reset driver")
Signed-off-by: Eugeniy Paltsev <Eugeniy.Paltsev@synopsys.com>
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/dtor/input
Pull more input updates from Dmitry Torokhov:
"A second round of updates for the input subsystem:
- a new driver for PWM-controlled vibrators
- ucb1400 touchscreen driver had completely busted suspend/resume
handling
- we now handle "home" button found on some devices with Goodix
touchscreens
- assorted other fixups"
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/dtor/input:
Input: i8042 - add Gigabyte P57 to the keyboard reset table
Input: xpad - validate USB endpoint type during probe
Input: ucb1400_ts - fix suspend and resume handling
Input: edt-ft5x06 - fix access to non-existing register
Input: elantech - make arrays debounce_packet static, reduces object code size
Input: surface3_spi - make const array header static, reduces object code size
Input: goodix - add support for capacitive home button
Input: add a driver for PWM controllable vibrators
Input: adi - make array seq static, reduces object code size
|
|
git://git.linux-mips.org/pub/scm/ralf/upstream-linus
Pull MIPS updates from Ralf Baechle:
"This is the main pull request for 4.14 for MIPS; below a summary of
the non-merge commits:
CM:
- Rename mips_cm_base to mips_gcr_base
- Specify register size when generating accessors
- Use BIT/GENMASK for register fields, order & drop shifts
- Add cluster & block args to mips_cm_lock_other()
CPC:
- Use common CPS accessor generation macros
- Use BIT/GENMASK for register fields, order & drop shifts
- Introduce register modify (set/clear/change) accessors
- Use change_*, set_* & clear_* where appropriate
- Add CM/CPC 3.5 register definitions
- Use GlobalNumber macros rather than magic numbers
- Have asm/mips-cps.h include CM & CPC headers
- Cluster support for topology functions
- Detect CPUs in secondary clusters
CPS:
- Read GIC_VL_IDENT directly, not via irqchip driver
DMA:
- Consolidate coherent and non-coherent dma_alloc code
- Don't use dma_cache_sync to implement fd_cacheflush
FPU emulation / FP assist code:
- Another series of 14 commits fixing corner cases such as NaN
propgagation and other special input values.
- Zero bits 32-63 of the result for a CLASS.D instruction.
- Enhanced statics via debugfs
- Do not use bools for arithmetic. GCC 7.1 moans about this.
- Correct user fault_addr type
Generic MIPS:
- Enhancement of stack backtraces
- Cleanup from non-existing options
- Handle non word sized instructions when examining frame
- Fix detection and decoding of ADDIUSP instruction
- Fix decoding of SWSP16 instruction
- Refactor handling of stack pointer in get_frame_info
- Remove unreachable code from force_fcr31_sig()
- Convert to using %pOF instead of full_name
- Remove the R6000 support.
- Move FP code from *_switch.S to *_fpu.S
- Remove unused ST_OFF from r2300_switch.S
- Allow platform to specify multiple its.S files
- Add #includes to various files to ensure code builds reliable and
without warning..
- Remove __invalidate_kernel_vmap_range
- Remove plat_timer_setup
- Declare various variables & functions static
- Abstract CPU core & VP(E) ID access through accessor functions
- Store core & VP IDs in GlobalNumber-style variable
- Unify checks for sibling CPUs
- Add CPU cluster number accessors
- Prevent direct use of generic_defconfig
- Make CONFIG_MIPS_MT_SMP default y
- Add __ioread64_copy
- Remove unnecessary inclusions of linux/irqchip/mips-gic.h
GIC:
- Introduce asm/mips-gic.h with accessor functions
- Use new GIC accessor functions in mips-gic-timer
- Remove counter access functions from irq-mips-gic.c
- Remove gic_read_local_vp_id() from irq-mips-gic.c
- Simplify shared interrupt pending/mask reads in irq-mips-gic.c
- Simplify gic_local_irq_domain_map() in irq-mips-gic.c
- Drop gic_(re)set_mask() functions in irq-mips-gic.c
- Remove gic_set_polarity(), gic_set_trigger(), gic_set_dual_edge(),
gic_map_to_pin() and gic_map_to_vpe() from irq-mips-gic.c.
- Convert remaining shared reg access, local int mask access and
remaining local reg access to new accessors
- Move GIC_LOCAL_INT_* to asm/mips-gic.h
- Remove GIC_CPU_INT* macros from irq-mips-gic.c
- Move various definitions to the driver
- Remove gic_get_usm_range()
- Remove __gic_irq_dispatch() forward declaration
- Remove gic_init()
- Use mips_gic_present() in place of gic_present and remove
gic_present
- Move gic_get_c0_*_int() to asm/mips-gic.h
- Remove linux/irqchip/mips-gic.h
- Inline __gic_init()
- Inline gic_basic_init()
- Make pcpu_masks a per-cpu variable
- Use pcpu_masks to avoid reading GIC_SH_MASK*
- Clean up mti, reserved-cpu-vectors handling
- Use cpumask_first_and() in gic_set_affinity()
- Let the core set struct irq_common_data affinity
microMIPS:
- Fix microMIPS stack unwinding on big endian systems
MIPS-GIC:
- SYNC after enabling GIC region
NUMA:
- Remove the unused parent_node() macro
R6:
- Constify r2_decoder_tables
- Add accessor & bit definitions for GlobalNumber
SMP:
- Constify smp ops
- Allow boot_secondary SMP op to return errors
VDSO:
- Drop gic_get_usm_range() usage
- Avoid use of linux/irqchip/mips-gic.h
Platform changes:
Alchemy:
- Add devboard machine type to cpuinfo
- update cpu feature overrides
- Threaded carddetect irqs for devboards
AR7:
- allow NULL clock for clk_get_rate
BCM63xx:
- Fix ENETDMA_6345_MAXBURST_REG offset
- Allow NULL clock for clk_get_rate
CI20:
- Enable GPIO and RTC drivers in defconfig
- Add ethernet and fixed-regulator nodes to DTS
Generic platform:
- Move Boston and NI 169445 FIT image source to their own files
- Include asm/bootinfo.h for plat_fdt_relocated()
- Include asm/time.h for get_c0_*_int()
- Include asm/bootinfo.h for plat_fdt_relocated()
- Include asm/time.h for get_c0_*_int()
- Allow filtering enabled boards by requirements
- Don't explicitly disable CONFIG_USB_SUPPORT
- Bump default NR_CPUS to 16
JZ4700:
- Probe the jz4740-rtc driver from devicetree
Lantiq:
- Drop check of boot select from the spi-falcon driver.
- Drop check of boot select from the lantiq-flash MTD driver.
- Access boot cause register in the watchdog driver through regmap
- Add device tree binding documentation for the watchdog driver
- Add docs for the RCU DT bindings.
- Convert the fpi bus driver to a platform_driver
- Remove ltq_reset_cause() and ltq_boot_select(
- Switch to a proper reset driver
- Switch to a new drivers/soc GPHY driver
- Add an USB PHY driver for the Lantiq SoCs using the RCU module
- Use of_platform_default_populate instead of __dt_register_buses
- Enable MFD_SYSCON to be able to use it for the RCU MFD
- Replace ltq_boot_select() with dummy implementation.
Loongson 2F:
- Allow NULL clock for clk_get_rate
Malta:
- Use new GIC accessor functions
NI 169445:
- Add support for NI 169445 board.
- Only include in 32r2el kernels
Octeon:
- Add support for watchdog of 78XX SOCs.
- Add support for watchdog of CN68XX SOCs.
- Expose support for mips32r1, mips32r2 and mips64r1
- Enable more drivers in config file
- Add support for accessing the boot vector.
- Remove old boot vector code from watchdog driver
- Define watchdog registers for 70xx, 73xx, 78xx, F75xx.
- Make CSR functions node aware.
- Allow access to CIU3 IRQ domains.
- Misc cleanups in the watchdog driver
Omega2+:
- New board, add support and defconfig
Pistachio:
- Enable Root FS on NFS in defconfig
Ralink:
- Add Mediatek MT7628A SoC
- Allow NULL clock for clk_get_rate
- Explicitly request exclusive reset control in the pci-mt7620 PCI driver.
SEAD3:
- Only include in 32 bit kernels by default
VoCore:
- Add VoCore as a vendor t0 dt-bindings
- Add defconfig file"
* '4.14-features' of git://git.linux-mips.org/pub/scm/ralf/upstream-linus: (167 commits)
MIPS: Refactor handling of stack pointer in get_frame_info
MIPS: Stacktrace: Fix microMIPS stack unwinding on big endian systems
MIPS: microMIPS: Fix decoding of swsp16 instruction
MIPS: microMIPS: Fix decoding of addiusp instruction
MIPS: microMIPS: Fix detection of addiusp instruction
MIPS: Handle non word sized instructions when examining frame
MIPS: ralink: allow NULL clock for clk_get_rate
MIPS: Loongson 2F: allow NULL clock for clk_get_rate
MIPS: BCM63XX: allow NULL clock for clk_get_rate
MIPS: AR7: allow NULL clock for clk_get_rate
MIPS: BCM63XX: fix ENETDMA_6345_MAXBURST_REG offset
mips: Save all registers when saving the frame
MIPS: Add DWARF unwinding to assembly
MIPS: Make SAVE_SOME more standard
MIPS: Fix issues in backtraces
MIPS: jz4780: DTS: Probe the jz4740-rtc driver from devicetree
MIPS: Ci20: Enable RTC driver
watchdog: octeon-wdt: Add support for 78XX SOCs.
watchdog: octeon-wdt: Add support for cn68XX SOCs.
watchdog: octeon-wdt: File cleaning.
...
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/wsa/linux
Pull more i2c updates from Wolfram Sang:
"I2C has two more new drivers: Altera FPGA and STM32F7"
* 'i2c/for-next' of git://git.kernel.org/pub/scm/linux/kernel/git/wsa/linux:
i2c: i2c-stm32f7: add driver
i2c: i2c-stm32f4: use generic definition of speed enum
dt-bindings: i2c-stm32: Document the STM32F7 I2C bindings
i2c: altera: Add Altera I2C Controller driver
dt-bindings: i2c: Add Altera I2C Controller
|
|
Pull watchdog updates from Wim Van Sebroeck:
- add support for the watchdog on Meson8 and Meson8m2
- add support for MediaTek MT7623 and MT7622 SoC
- add support for the r8a77995 wdt
- explicitly request exclusive reset control for asm9260_wdt,
zx2967_wdt, rt2880_wdt and mt7621_wdt
- improvements to asm9260_wdt, aspeed_wdt, renesas_wdt and cadence_wdt
- add support for reading freq via CCF + suspend/resume support for
of_xilinx_wdt
- constify watchdog_ops and various device-id structures
- revert of commit 1fccb73011ea ("iTCO_wdt: all versions count down
twice") (Bug 196509)
* git://www.linux-watchdog.org/linux-watchdog: (40 commits)
watchdog: mei_wdt: constify mei_cl_device_id
watchdog: sp805: constify amba_id
watchdog: ziirave: constify i2c_device_id
watchdog: sc1200: constify pnp_device_id
dt-bindings: watchdog: renesas-wdt: Add support for the r8a77995 wdt
watchdog: renesas_wdt: update copyright dates
watchdog: renesas_wdt: make 'clk' a variable local to probe()
watchdog: renesas_wdt: consistently use RuntimePM for clock management
watchdog: aspeed: Support configuration of external signal properties
dt-bindings: watchdog: aspeed: External reset signal properties
drivers/watchdog: Add optional ASPEED device tree properties
drivers/watchdog: ASPEED reference dev tree properties for config
watchdog: da9063_wdt: Simplify by removing unneeded struct...
watchdog: bcm7038: Check the return value from clk_prepare_enable()
watchdog: qcom: Check for platform_get_resource() failure
watchdog: of_xilinx_wdt: Add suspend/resume support
watchdog: of_xilinx_wdt: Add support for reading freq via CCF
dt-bindings: watchdog: mediatek: add support for MediaTek MT7623 and MT7622 SoC
watchdog: max77620_wdt: constify platform_device_id
watchdog: pcwd_usb: constify usb_device_id
...
|
|
This patch adds the documentation of device tree bindings for STM32F7 I2C
Signed-off-by: M'boumba Cedric Madianga <cedric.madianga@gmail.com>
Signed-off-by: Pierre-Yves MORDRET <pierre-yves.mordret@st.com>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
|
|
Add the documentation to support the Altera synthesizable
logic I2C Controller in FPGA.
Signed-off-by: Thor Thayer <thor.thayer@linux.intel.com>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
|
