| Age | Commit message (Collapse) | Author |
|---|
|
As suggested by the reference manual in a note in chapter 13.2
this commit disables the keeper and enables a 100k pull-down on the
adc pins.
Related-to: ELB-2690
Signed-off-by: Philippe Schenker <philippe.schenker@toradex.com>
|
|
There is now a mainline variant for a regulator-fixed to be enabled
by a clock. Make use of this newly cherry-picked mainline feature.
Signed-off-by: Philippe Schenker <philippe.schenker@toradex.com>
|
|
Signed-off-by: Philippe Schenker <philippe.schenker@toradex.com>
|
|
Some pinmuxings are obviously wrong, originating from a copy/paste
error. This patch corrects that with the following strategy:
- Set all reserved bits to zero
- Leave drive strength and slew rate as is
- Add sensible pull and hysteresis depending on the function of the pin
- Not used pins are muxed to their reset-value defined by the SoC
Signed-off-by: Philippe Schenker <philippe.schenker@toradex.com>
|
|
Cosmetic change: Rename the reg_sd1_vmmc to reg_sd1_vqmmc as it is
used for vqmmc.
Signed-off-by: Max Krummenacher <max.krummenacher@toradex.com>
|
|
The correct spelling for the property is gpios, otherwise the regulator
will neither reserve nor control any gpio(s).
Thus any SD/MMC card which can use UHS 1 modes will fail.
Related-to: #46566
Signed-off-by: Max Krummenacher <max.krummenacher@toradex.com>
|
|
While at it, add the dtbs for Aster Carrier Board to the Makefile.
Signed-off-by: Max Krummenacher <max.krummenacher@toradex.com>
|
|
In 4.14 devicetress are based on the mainline DT's and only necessary
stuff for downstream is put into those devicetrees.
This commit holds the changes for imx6ull*colibri* from 4.9.
Signed-off-by: Philippe Schenker <philippe.schenker@toradex.com>
|
|
Reduce the current drawn from VCC_BATT when the main power on the 3V3 pins
to the module are switched off.
This switches off SoC internal pull resistors which are provided on the module
for TAMPER7 and TAMPER9 SoC pin and switches on a pull down instead of a pullup
for the USBC_DET module pin (TAMPER2).
Signed-off-by: Max Krummenacher <max.krummenacher@toradex.com>
Acked-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
(cherry picked from commit 9fd59b6eebd12106b5b53fc56466bcd89b9a7ee9)
Conflicts:
arch/arm/boot/dts/imx6ull-colibri.dtsi
Signed-off-by: Philippe Schenker <philippe.schenker@toradex.com>
|
|
This patch adds the watchdog to the imx6ull-colibri devicetree
Signed-off-by: Philippe Schenker <philippe.schenker@toradex.com>
|
|
Add the pinmuxing and a inactive node for flexcan1 on SODIMM 55/63
and move the inactive flexcan modes to imx6ull-colibri-eval-v3.dtsi
where they belong.
Note that this commit does not enable flexcan functionality, but rather
eases the effort needed to do so.
Signed-off-by: Max Krummenacher <max.krummenacher@toradex.com>
Acked-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
(cherry picked from commit 983ff8a6b61e9466beb6b4781fb370a6a7da937a)
Conflicts:
arch/arm/boot/dts/imx6ull-colibri-nonwifi.dtsi
arch/arm/boot/dts/imx6ull-colibri-wifi.dtsi
arch/arm/boot/dts/imx6ull-colibri.dtsi
Signed-off-by: Philippe Schenker <philippe.schenker@toradex.com
|
|
Signed-off-by: Philippe Schenker <philippe.schenker@toradex.com>
Acked-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
(cherry picked from commit a6f40c3a1d659467267a9d16355c788524bc5ca7)
Conflicts:
arch/arm/boot/dts/imx6ull-colibri.dtsi
Signed-off-by: Philippe Schenker <philippe.schenker@toradex.com>
|
|
Switch on 22 kOhm pull ups and lower the I2C frequency to around 40kHz
to get a more reliable communication.
Signed-off-by: Max Krummenacher <max.krummenacher@toradex.com>
|
|
Since commit d2d0ad2aec4a ("i2c: imx: use open drain for recovery
GPIO") GPIO lib expects this GPIO to be configured as open drain.
Make sure we define this GPIO as open drain in the device tree.
This gets rid of the following warning:
gpio-81 (scl): enforced open drain please flag it properly in DT/ACPI DSDT/board file
Note that currently the i.MX pinctrl driver does not support
enabling open drain directly, so this patch has no effect in
practice. Open drain is enabled by the fixed pinmux entry.
Signed-off-by: Stefan Agner <stefan@agner.ch>
Reviewed-by: Philippe Schenker <philippe.schenker@toradex.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
(cherry picked from commit d2b91ab1480618885fe0a7f240b7e7710344a066)
|
|
Add support for the Computer on Module Colibri iMX6ULL and its
Bluetooth/Wifi variant along with the development/evaluation carrier
board device trees. Follow the usual hierarchic include model,
maintaining shared configuration in imx6ull-colibri.dtsi and
imx6ull-colibri-eval-v3.dtsi respectively.
Signed-off-by: Stefan Agner <stefan@agner.ch>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
(cherry picked from commit c2e4987e0e02095ed3d19e958b3891954ef38243)
|
