Age | Commit message (Collapse) | Author |
|
problems with booting
Without that change booting leads to crash with more warnings like below:
[ 0.284454] omap_hwmod: uart4: cannot clk_get main_clk uart4_fck
[ 0.284484] omap_hwmod: uart4: cannot _init_clocks
[ 0.284484] ------------[ cut here ]------------
[ 0.284545] WARNING: CPU: 0 PID: 1 at arch/arm/mach-omap2/omap_hwmod.c:2543 _init+0x300/0x3e4()
[ 0.284545] omap_hwmod: uart4: couldn't init clocks
[ 0.284576] Modules linked in:
[ 0.284606] CPU: 0 PID: 1 Comm: swapper/0 Not tainted 3.13.0-next-20140124-00020-gd2aefec-dirty #26
[ 0.284637] [<c00151c0>] (unwind_backtrace) from [<c0011e20>] (show_stack+0x10/0x14)
[ 0.284667] [<c0011e20>] (show_stack) from [<c0568544>] (dump_stack+0x7c/0x94)
[ 0.284729] [<c0568544>] (dump_stack) from [<c003ff94>] (warn_slowpath_common+0x6c/0x90)
[ 0.284729] [<c003ff94>] (warn_slowpath_common) from [<c003ffe8>] (warn_slowpath_fmt+0x30/0x40)
[ 0.284759] [<c003ffe8>] (warn_slowpath_fmt) from [<c07d1be8>] (_init+0x300/0x3e4)
[ 0.284790] [<c07d1be8>] (_init) from [<c07d217c>] (__omap_hwmod_setup_all+0x40/0x8c)
[ 0.284820] [<c07d217c>] (__omap_hwmod_setup_all) from [<c0008918>] (do_one_initcall+0xe8/0x14c)
[ 0.284851] [<c0008918>] (do_one_initcall) from [<c07c5c18>] (kernel_init_freeable+0x104/0x1c8)
[ 0.284881] [<c07c5c18>] (kernel_init_freeable) from [<c0563524>] (kernel_init+0x8/0x118)
[ 0.284912] [<c0563524>] (kernel_init) from [<c000e368>] (ret_from_fork+0x14/0x2c)
[ 0.285064] ---[ end trace 63de210ad43b627d ]---
Reference:
https://lkml.org/lkml/2013/10/8/553
Signed-off-by: Marek Belisko <marek@goldelico.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
|
Does not have an aux supply, and must be non-removable.
Otherwise it is removed during suspend and filesystem gets confused.
Signed-off-by: NeilBrown <neilb@suse.de>
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
|
It should be ACTIVE_HIGH.
Signed-off-by: NeilBrown <neilb@suse.de>
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
|
BMP085 EOC (End Of Conversion) irq line is connected to
gpio113 on gta04. Set irq properties to have driver using irq
instead polling for EOC.
Signed-off-by: Marek Belisko <marek@goldelico.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
|
The generic PHY framewrok expects different properties than the
old USB PHY framework. Supply those properties.
Fixes USB OTG port on GAT04 and N900 after the Generic PHY framework was
merged in greg/usb-next. [1]
[1] - https://lkml.org/lkml/2013/9/27/581
Signed-off-by: Roger Quadros <rogerq@ti.com>
Acked-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Benoit Cousson <bcousson@baylibre.com>
|
|
This adds devicetree for gta04 (Openmoko next generation board) with necessary
support for mmc, usb, leds and button.
Signed-off-by: Marek Belisko <marek@goldelico.com>
Signed-off-by: Benoit Cousson <bcousson@baylibre.com>
|