summaryrefslogtreecommitdiff
path: root/arch/arm/boot/dts/stm32mp157c-ev1.dts
AgeCommit message (Collapse)Author
2019-11-06ARM: dts: stm32: change joystick pinctrl definition on stm32mp157c-ev1Amelie Delaunay
Pins used for joystick are all configured as input. "push-pull" is not a valid setting for an input pin. Fixes: a502b343ebd0 ("pinctrl: stmfx: update pinconf settings") Signed-off-by: Alexandre Torgue <alexandre.torgue@st.com> Signed-off-by: Amelie Delaunay <amelie.delaunay@st.com> Signed-off-by: Alexandre Torgue <alexandre.torgue@st.com>
2019-11-06ARM: dts: stm32: remove OV5640 pinctrl definition on stm32mp157c-ev1Amelie Delaunay
"push-pull" configuration is now fully handled by the gpiolib and the STMFX pinctrl driver. There is no longer need to declare a pinctrl group to only configure "push-pull" setting for the line. It is done directly by the gpiolib. Fixes: a502b343ebd0 ("pinctrl: stmfx: update pinconf settings") Signed-off-by: Alexandre Torgue <alexandre.torgue@st.com> Signed-off-by: Amelie Delaunay <amelie.delaunay@st.com> Signed-off-by: Alexandre Torgue <alexandre.torgue@st.com>
2019-08-02ARM: dts: stm32: add phy-dsi-supply property on stm32mp157c-ev1Yannick Fertré
The dsi physical layer is powered by the 1v8 power controller supply. Signed-off-by: Yannick Fertré <yannick.fertre@st.com> Signed-off-by: Alexandre Torgue <alexandre.torgue@st.com>
2019-07-25ARM: dts: stm32: enable FMC2 NAND controller on stm32mp157c-ev1Christophe Kerello
This patch enables FMC2 NAND controller used on stm32mp157c-ev1. Signed-off-by: Christophe Kerello <christophe.kerello@st.com> Signed-off-by: Alexandre Torgue <alexandre.torgue@st.com>
2019-06-21ARM: dts: stm32: replace rgmii mode with rgmii-id on stm32mp15 boardsChristophe Roullier
On disco and eval board, Tx and Rx delay are applied (pull-up of 4.7k put on VDD) so which correspond to RGMII-ID mode with internal RX and TX delays provided by the PHY, the MAC should not add the RX or TX delays in this case Signed-off-by: Christophe Roullier <christophe.roullier@st.com> Signed-off-by: Alexandre Torgue <alexandre.torgue@st.com>
2019-06-21ARM: dts: stm32: add power supply of rm68200 on stm32mp157c-ev1Yannick Fertré
This patch adds a new property (power-supply) to panel rm68200 (raydium) on stm32mp157c-ev1. Signed-off-by: Yannick Fertré <yannick.fertre@st.com> Signed-off-by: Alexandre Torgue <alexandre.torgue@st.com>
2019-05-21ARM: dts: stm32: enable OV5640 camera on stm32mp157c-ev1 boardHugues Fruchet
Enable OV5640 camera sensor driver of MB1379A extension board connected on CN7 connector of stm32mp157c-ev1 board: bus-width is set to 8, data-shift is set to 2 (lines 9:2 are used), hsync-active is set to 0 for horizontal synchro line active low, vsync-active is set to 0 for vertical synchro line active low and pclk-sample is set to 1 for pixel clock polarity sampling data on rising edge of the pixel clock signal. Signed-off-by: Hugues Fruchet <hugues.fruchet@st.com> Signed-off-by: Alexandre Torgue <alexandre.torgue@st.com>
2019-05-21ARM: dts: stm32: add jedec compatible for nor flash on stm32mp157c-ev1Ludovic Barre
This patch adds jedec compatible for spi-nor flash on stm32mp157c-ev1 (needed with new spi-mem interface). Signed-off-by: Ludovic Barre <ludovic.barre@st.com> Signed-off-by: Alexandre Torgue <alexandre.torgue@st.com>
2019-05-21ARM: dts: stm32: add pinctrl sleep config for qspi on stm32mp157c-ev1Ludovic Barre
This patch adds pinctrl sleep config for qspi on stm32mp157c-ev1 Signed-off-by: Ludovic Barre <ludovic.barre@st.com> Signed-off-by: Alexandre Torgue <alexandre.torgue@st.com>
2019-05-21ARM: dts: stm32: add joystick support on stm32mp157c-ev1Amelie Delaunay
The joystick (B1) on stm32mp157c-ev1 uses gpios on STMFX gpio expander. These gpios need a pin configuration (push-pull and bias-pull-down), described under stmfx_pinctrl node. Signed-off-by: Amelie Delaunay <amelie.delaunay@st.com> Signed-off-by: Alexandre Torgue <alexandre.torgue@st.com>
2019-05-21ARM: dts: stm32: add STMFX support on stm32mp157c-ev1Amelie Delaunay
This patch adds support for STMicroelectronics Multi-Function eXpander (STMFX) on stm32mp157c-ev1. It is connected on i2c2. Signed-off-by: Amelie Delaunay <amelie.delaunay@st.com> Signed-off-by: Alexandre Torgue <alexandre.torgue@st.com>
2018-12-03ARM: dts: stm32: add can1 sleep pins muxing on stm32mp157c-ev1 boardBich HEMON
Add pinctrl sleep state for can1 on stm32mp157c-ev1. Signed-off-by: Bich Hemon <bich.hemon@st.com> Signed-off-by: Alexandre Torgue <alexandre.torgue@st.com>
2018-11-12ARM: dts: stm32: don't use timers dmas on stm32mp157c-ev1Fabrice Gasnier
Spare dmas when using timers on stm32mp157c-ev1. Signed-off-by: Fabrice Gasnier <fabrice.gasnier@st.com> Signed-off-by: Alexandre Torgue <alexandre.torgue@st.com>
2018-09-21ARM: dts: stm32: enable display on stm32mp157c-ev1 boardYannick Fertré
Enable panel raydium RM68200, DSI bridge & display controller. Signed-off-by: Yannick Fertré <yannick.fertre@st.com> Signed-off-by: Alexandre Torgue <alexandre.torgue@st.com>
2018-07-13ARM: dts: stm32: add support of ethernet on stm32mp157c-ev1Christophe Roullier
MAC is connected to a PHY in RGMII mode. Signed-off-by: Christophe Roullier <christophe.roullier@st.com> Signed-off-by: Alexandre Torgue <alexandre.torgue@st.com>
2018-07-13ARM: dts: stm32: add SPI1 support on stm32mp157c-ev1Amelie Delaunay
This patch adds SPI1 support on stm32mp157c-ev1 board. SPI1 is available on GPIO expansion connector but kept disabled so these pins can be used as GPIOs by default. Signed-off-by: Amelie Delaunay <amelie.delaunay@st.com> Signed-off-by: Alexandre Torgue <alexandre.torgue@st.com>
2018-07-13ARM: dts: stm32: enable USB OTG HS on stm32mp157c-ev1Amelie Delaunay
This patch enables USB OTG HS on stm32mp157c-ev1 in Peripheral mode. Signed-off-by: Amelie Delaunay <amelie.delaunay@st.com> Signed-off-by: Alexandre Torgue <alexandre.torgue@st.com>
2018-07-13ARM: dts: stm32: enable USB Host (USBH) EHCI controller on stm32mp157c-ev1Amelie Delaunay
This patch enables USB Host (USBH) EHCI controller on stm32mp157c-ev1. As a hub is used between USBH and USB connectors, no need to enable USBH OHCI controller: all low- and full-speed traffic is managed by the hub. Signed-off-by: Amelie Delaunay <amelie.delaunay@st.com> Signed-off-by: Alexandre Torgue <alexandre.torgue@st.com>
2018-06-25ARM: dts: stm32: m_can activation on stm32mp157c-ev1Erwan Le Ray
Add activation of the Controller Area Network m_can on stm32mp157c-ev1 board. Signed-off-by: Bich Hemon <bich.hemon@st.com> Signed-off-by: Erwan Le Ray <erwan.leray@st.com> Signed-off-by: Alexandre Torgue <alexandre.torgue@st.com>
2018-05-04ARM: dts: stm32: add flash nor support on stm32mp157c eval boardLudovic Barre
This patch adds flash nor on qspi. Each flash is connected in quad mode and has its own chip select. Signed-off-by: Ludovic Barre <ludovic.barre@st.com> Signed-off-by: Alexandre Torgue <alexandre.torgue@st.com>
2018-05-04ARM: dts: stm32: add cec support on stm32mp157c-ev1yannick fertre
This patch enables cec node on stm32mp157c-ev1 board Signed-off-by: Yannick Fertre <yannick.fertre@st.com> Signed-off-by: Alexandre Torgue <alexandre.torgue@st.com>
2018-05-04ARM: dts: stm32: enable USBPHYC on stm32mp157c-ev1Amelie Delaunay
This patch enables USBPHYC (USB PHY Controller) on stm32mp157c-ev1. This enables the two usbphyc usb2 ports. Signed-off-by: Amelie Delaunay <amelie.delaunay@st.com> Signed-off-by: Alexandre Torgue <alexandre.torgue@st.com>
2018-05-04ARM: dts: stm32: Add I2C2/5 support for STM32MP157C-EV1Pierre-Yves MORDRET
Add I2C1/5 support for STM32MP157C evaluation daughter on evaluation mother board. Signed-off-by: Pierre-Yves MORDRET <pierre-yves.mordret@st.com> Signed-off-by: Alexandre Torgue <alexandre.torgue@st.com>
2018-05-02ARM: dts: stm32: add PWM and triggers on stm32mp157c-ev1 boardFabrice Gasnier
stm32mp157c evaluation board has TIM2_CH4, TIM8_CH4 and TIM12_CH1 available on GPIO expansion connector. Add PWM and associated triggers (for ADC/DAC) on these timers. Keep them disabled so these pins can be used as GPIOs by default. Signed-off-by: Fabrice Gasnier <fabrice.gasnier@st.com> Signed-off-by: Alexandre Torgue <alexandre.torgue@st.com>
2018-02-26ARM: dts: stm32: add initial support of stm32mp157c eval boardLudovic Barre
Add support of stm32mp157c evaluation board (part number: STM32MP157C-EV1) split in 2 elements: -Daughter board (part number: STM32MP157C-ED1) which includes CPU, memory and power supply -Mother board (part number: STM32MP157C-EM1) which includes external peripherals (like display, camera,...) and extension connectors. The daughter board can run alone, this is why the device tree files are split in two layers, for the complete evaluation board (ev1) and for the daughter board alone (ed1). Signed-off-by: Ludovic Barre <ludovic.barre@st.com> Signed-off-by: Alexandre Torgue <alexandre.torgue@st.com>
generated by cgit v1.2.3 (git 2.0.4) at 2024-06-02 11:39:19 +0000