| Age | Commit message (Collapse) | Author |
|---|
|
Pull networking updates from David Miller:
"Highlights:
1) Support more Realtek wireless chips, from Jes Sorenson.
2) New BPF types for per-cpu hash and arrap maps, from Alexei
Starovoitov.
3) Make several TCP sysctls per-namespace, from Nikolay Borisov.
4) Allow the use of SO_REUSEPORT in order to do per-thread processing
of incoming TCP/UDP connections. The muxing can be done using a
BPF program which hashes the incoming packet. From Craig Gallek.
5) Add a multiplexer for TCP streams, to provide a messaged based
interface. BPF programs can be used to determine the message
boundaries. From Tom Herbert.
6) Add 802.1AE MACSEC support, from Sabrina Dubroca.
7) Avoid factorial complexity when taking down an inetdev interface
with lots of configured addresses. We were doing things like
traversing the entire address less for each address removed, and
flushing the entire netfilter conntrack table for every address as
well.
8) Add and use SKB bulk free infrastructure, from Jesper Brouer.
9) Allow offloading u32 classifiers to hardware, and implement for
ixgbe, from John Fastabend.
10) Allow configuring IRQ coalescing parameters on a per-queue basis,
from Kan Liang.
11) Extend ethtool so that larger link mode masks can be supported.
From David Decotigny.
12) Introduce devlink, which can be used to configure port link types
(ethernet vs Infiniband, etc.), port splitting, and switch device
level attributes as a whole. From Jiri Pirko.
13) Hardware offload support for flower classifiers, from Amir Vadai.
14) Add "Local Checksum Offload". Basically, for a tunneled packet
the checksum of the outer header is 'constant' (because with the
checksum field filled into the inner protocol header, the payload
of the outer frame checksums to 'zero'), and we can take advantage
of that in various ways. From Edward Cree"
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-next: (1548 commits)
bonding: fix bond_get_stats()
net: bcmgenet: fix dma api length mismatch
net/mlx4_core: Fix backward compatibility on VFs
phy: mdio-thunder: Fix some Kconfig typos
lan78xx: add ndo_get_stats64
lan78xx: handle statistics counter rollover
RDS: TCP: Remove unused constant
RDS: TCP: Add sysctl tunables for sndbuf/rcvbuf on rds-tcp socket
net: smc911x: convert pxa dma to dmaengine
team: remove duplicate set of flag IFF_MULTICAST
bonding: remove duplicate set of flag IFF_MULTICAST
net: fix a comment typo
ethernet: micrel: fix some error codes
ip_tunnels, bpf: define IP_TUNNEL_OPTS_MAX and use it
bpf, dst: add and use dst_tclassid helper
bpf: make skb->tc_classid also readable
net: mvneta: bm: clarify dependencies
cls_bpf: reset class and reuse major in da
ldmvsw: Checkpatch sunvnet.c and sunvnet_common.c
ldmvsw: Add ldmvsw.c driver code
...
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/char-misc
Pull char/misc updates from Greg KH:
"Here is the big char/misc driver update for 4.6-rc1.
The majority of the patches here is hwtracing and some new mic
drivers, but there's a lot of other driver updates as well. Full
details in the shortlog.
All have been in linux-next for a while with no reported issues"
* tag 'char-misc-4.6-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/char-misc: (238 commits)
goldfish: Fix build error of missing ioremap on UM
nvmem: mediatek: Fix later provider initialization
nvmem: imx-ocotp: Fix return value of imx_ocotp_read
nvmem: Fix dependencies for !HAS_IOMEM archs
char: genrtc: replace blacklist with whitelist
drivers/hwtracing: make coresight-etm-perf.c explicitly non-modular
drivers: char: mem: fix IS_ERROR_VALUE usage
char: xillybus: Fix internal data structure initialization
pch_phub: return -ENODATA if ROM can't be mapped
Drivers: hv: vmbus: Support kexec on ws2012 r2 and above
Drivers: hv: vmbus: Support handling messages on multiple CPUs
Drivers: hv: utils: Remove util transport handler from list if registration fails
Drivers: hv: util: Pass the channel information during the init call
Drivers: hv: vmbus: avoid unneeded compiler optimizations in vmbus_wait_for_unload()
Drivers: hv: vmbus: remove code duplication in message handling
Drivers: hv: vmbus: avoid wait_for_completion() on crash
Drivers: hv: vmbus: don't loose HVMSG_TIMER_EXPIRED messages
misc: at24: replace memory_accessor with nvmem_device_read
eeprom: 93xx46: extend driver to plug into the NVMEM framework
eeprom: at25: extend driver to plug into the NVMEM framework
...
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/sre/linux-power-supply
Pull power supply and reset changes from Sebastian Reichel:
- add types for USB Type C and PD chargers
- add act8945a charger driver
- add ACPI/DT bindings for goldfish-battery
- add support for versatile reset controller
- misc fixes
* tag 'for-v4.6' of git://git.kernel.org/pub/scm/linux/kernel/git/sre/linux-power-supply: (24 commits)
power: pm2301-charger: use __maybe_unused to hide pm functions
power: ipaq-micro-battery: use __maybe_unused to hide pm functions
power_supply: 88pm860x_charger: do not pass NULL to power_supply_put
jz4740-battery: Correct voltage change check
power_supply: lp8788-charger: initialize boolean 'found'
goldfish: Enable ACPI-based enumeration for goldfish battery
power: goldfish_battery: add devicetree bindings
power: act8945a: add charger driver for ACT8945A
power: add documentation for ACT8945A's charger DT bindings
ARM: dts: n900: Rename isp1704 to isp1707 to match correct name
power_supply: bq27xxx_battery: Add of modalias and match table when CONFIG_OF is enabled
power_supply: bq2415x_charger: Add of modalias and match table when CONFIG_OF is enabled
power_supply: bq2415x_charger: Do not add acpi modalias when CONFIG_ACPI is not enabled
power_supply: isp1704_charger: Add compatible of match for nxp,isp1707
power_supply: isp1704_charger: Error messages when probe fail
power_supply: Add types for USB Type C and PD chargers
power: bq24735-charger: add 'ti,external-control' option
power: bq24735-charger: document 'ti,external-control' option
power: bq24735-charger: fix failed i2c with ac-detect
power: reset: Fix dependencies for !HAS_IOMEM archs
...
|
|
This patch adds the emac device node for rk3036 SoCs.
We need to let mac clock under the DPLL which is able to provide
the accurate 50MHz what mac_ref need, since that will cause some
unstable things if the cpufreq is working.
Signed-off-by: Xing Zheng <zhengxing@rock-chips.com>
Signed-off-by: Caesar Wang <wxt@rock-chips.com>
Cc: linux-rockchip@lists.infradead.org
Cc: Xing Zheng <zhengxing@rock-chips.com>
Cc: Heiko Stuebner <heiko@sntech.de>
Cc: linux-arm-kernel@lists.infradead.org
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Pull EDAC updates from Borislav Petkov:
- Altera: L2 cache and On-Chip RAM support (Thor Thayer).
- EDAC: Workqueue handling cleanups (Borislav Petkov).
- Xgene: Register bus error handling (Loc Ho).
- Misc small fixes.
* tag 'edac_for_4.6' of git://git.kernel.org/pub/scm/linux/kernel/git/bp/bp:
ARM: socfpga: Enable OCRAM ECC on startup
ARM: socfpga: Enable L2 cache ECC on startup
ARM: dts: Add Altera L2 Cache and OCRAM EDAC entries
EDAC, altera: Add Altera L2 cache and OCRAM support
EDAC: Use edac_debugfs_remove_recursive() in edac_debugfs_exit()
EDAC, mpc85xx: Silence unused variable warning
EDAC: Cleanup/sync workqueue functions
EDAC: Kill workqueue setup/teardown functions
EDAC: Balance workqueue setup and teardown
arm64: Update the APM X-Gene EDAC node with the RB register resource
EDAC, xgene: Add missing SoC register bus error handling
Documentation, EDAC: Update xgene binding for missing register bus
EDAC, amd64_edac: Shift wrapping issue in f1x_get_norm_dct_addr()
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/groeck/linux-staging
Pull hwmon updates from Guenter Roeck:
- New drivers for NSA320 and LTC2990
- Added support for ADM1278 to adm1275 driver
- Added support for ncpXXxh103 to ntc_thermistor driver
- Renamed vexpress hwmon implementation
- Minor cleanups and improvements
* tag 'hwmon-for-linus-v4.6' of git://git.kernel.org/pub/scm/linux/kernel/git/groeck/linux-staging:
hwmon: Create an NSA320 hardware monitoring driver
hwmon: Define binding for the nsa320-hwmon driver
hwmon: (adm1275) Add support for ADM1278
hwmon: (ntc_thermistor) Add support for ncpXXxh103
Doc: hwmon: Fix typo "montoring" in hwmon
ARM: dts: vfxxx: Add iio_hwmon node for ADC temperature channel
ARM: dts: Change iio_hwmon nodes to use hypen in node names
hwmon: (iio_hwmon) Allow the driver to accept hypen in device tree node names
hwmon: Add LTC2990 sensor driver
hwmon: (vexpress) rename vexpress hwmon implementation
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-pinctrl
Pull pin control updates from Linus Walleij:
"An almost purely driver related set of changes with no major changes
to the framework, only one patch adding an unlocked version of the
pinctrl_find_gpio_range_from_pin() library call.
New drivers:
- ST Microelectronics STM32 MCU support: this is a non-MMU low-end
platform for IoT things (etc).
- Microchip PIC32 MCU support: same story as for STM32.
New subdrivers:
- Allwinner SunXi H3 R_PIO controller support.
- Qualcomm IPQ4019 support.
- MediaTek MT2701 and MT7623.
- Allwinner A64
Non-critical fixes:
- gpio_disable_free() for the Vybrid.
- pinctrl single: use a separate lockdep class.
Misc:
- Substantial cleanups and rewrites for the Super-H PFC driver and
subdrivers.
- Various fixes and cleanups, especially Paul Gortmakers work to make
nonmodular drivers nonmodular"
* tag 'pinctrl-v4.6-1' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-pinctrl: (75 commits)
pinctrl: single: Use a separate lockdep class
drivers: pinctrl: add driver for Allwinner A64 SoC
pinctrl: Broadcom Northstar2 pinctrl device tree bindings
pinctrl: amlogic: Make driver independent from two-domain configuration
pinctrl: amlogic: Separate some pin functions for Meson8 / Meson8b
pinctrl: at91: use __maybe_unused to hide pm functions
pinctrl: sh-pfc: core: don't open code of_device_get_match_data()
pinctrl: uniphier: rename CONFIG options and file names
pinctrl: sunxi: make A80 explicitly non-modular
pinctrl: stm32: make explicitly non-modular
pinctrl: sh-pfc: make explicitly non-modular
pinctrl: meson: make explicitly non-modular
pinctrl: pinctrl-mt6397 driver explicitly non-modular
pinctrl: sunxi: does not need module.h
pinctrl: pxa2xx: export symbols
pinctrl: sunxi: Change mux setting on PI irq pins
pinctrl: sunxi: Remove non existing irq's
pinctrl: imx: attach iomuxc device to gpr syscon
pinctrl-bcm2835: Fix cut-and-paste error in "pull" parsing
pinctrl: lpc1850-scu: document nxp,gpio-pin-interrupt
...
|
|
Allow Openblock AX3 using hardware buffer management with mvneta.
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Since mvneta driver supports using hardware buffer management (BM), in
order to use it, board files have to be adjusted accordingly. This commit
enables BM on AXP-DB and AXP-GP in same manner - because number of ports
on those boards is the same as number of possible pools, each port is
supposed to use single pool for all kind of packets.
Moreover appropriate entry is added to 'soc' node ranges, as well as "okay"
status for 'bm' and 'bm-bppi' (internal SRAM) nodes.
Signed-off-by: Marcin Wojtas <mw@semihalf.com>
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Armada XP network controller supports hardware buffer management (BM).
Since it is now enabled in mvneta driver, appropriate nodes can be added
to armada-xp.dtsi - for the actual common BM unit (bm@c0000) and its
internal SRAM (bm-bppi), which is used for indirect access to buffer
pointer ring residing in DRAM.
Pools - ports mapping, bm-bppi entry in 'soc' node's ranges and optional
parameters are supposed to be set in board files.
Signed-off-by: Marcin Wojtas <mw@semihalf.com>
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Since mvneta driver supports using hardware buffer management (BM), in
order to use it, board files have to be adjusted accordingly. This commit
enables BM on:
* A385-DB-AP - each port has its own pool for long and common pool for
short packets,
* A388-ClearFog - same as above,
* A388-DB - to each port unique 'short' and 'long' pools are mapped,
* A388-GP - same as above.
Moreover appropriate entry is added to 'soc' node ranges, as well as "okay"
status for 'bm' and 'bm-bppi' (internal SRAM) nodes.
[gregory.clement@free-electrons.com: add suppport for the ClearFog board]
Signed-off-by: Marcin Wojtas <mw@semihalf.com>
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
Acked-by: Russell King <rmk+kernel@arm.linux.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Armada 38x network controller supports hardware buffer management (BM).
Since it is now enabled in mvneta driver, appropriate nodes can be added
to armada-38x.dtsi - for the actual common BM unit (bm@c8000) and its
internal SRAM (bm-bppi), which is used for indirect access to buffer
pointer ring residing in DRAM.
Pools - ports mapping, bm-bppi entry in 'soc' node's ranges and optional
parameters are supposed to be set in board files.
Signed-off-by: Marcin Wojtas <mw@semihalf.com>
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
When the Crypto SRAM mappings were added to the Device Tree files
describing the Armada XP boards in commit c466d997bb16 ("ARM: mvebu:
define crypto SRAM ranges for all armada-xp boards"), the fact that
those mappings were overlaping with the PCIe memory aperture was
overlooked. Due to this, we currently have for all Armada XP platforms
a situation that looks like this:
Memory mapping on Armada XP boards with internal registers at
0xf1000000:
- 0x00000000 -> 0xf0000000 3.75G RAM
- 0xf0000000 -> 0xf1000000 16M NOR flashes (AXP GP / AXP DB)
- 0xf1000000 -> 0xf1100000 1M internal registers
- 0xf8000000 -> 0xffe0000 126M PCIe memory aperture
- 0xf8100000 -> 0xf8110000 64KB Crypto SRAM #0 => OVERLAPS WITH PCIE !
- 0xf8110000 -> 0xf8120000 64KB Crypto SRAM #1 => OVERLAPS WITH PCIE !
- 0xffe00000 -> 0xfff00000 1M PCIe I/O aperture
- 0xfff0000 -> 0xffffffff 1M BootROM
The overlap means that when PCIe devices are added, depending on their
memory window needs, they might or might not be mapped into the
physical address space. Indeed, they will not be mapped if the area
allocated in the PCIe memory aperture by the PCI core overlaps with
one of the Crypto SRAM. Typically, a Intel IGB PCIe NIC that needs 8MB
of PCIe memory will see its PCIe memory window allocated from
0xf80000000 for 8MB, which overlaps with the Crypto SRAM windows. Due
to this, the PCIe window is not created, and any attempt to access the
PCIe window makes the kernel explode:
[ 3.302213] igb: Copyright (c) 2007-2014 Intel Corporation.
[ 3.307841] pci 0000:00:09.0: enabling device (0140 -> 0143)
[ 3.313539] mvebu_mbus: cannot add window '4:f8', conflicts with another window
[ 3.320870] mvebu-pcie soc:pcie-controller: Could not create MBus window at [mem 0xf8000000-0xf87fffff]: -22
[ 3.330811] Unhandled fault: external abort on non-linefetch (0x1008) at 0xf08c0018
This problem does not occur on Armada 370 boards, because we use the
following memory mapping (for boards that have internal registers at
0xf1000000):
- 0x00000000 -> 0xf0000000 3.75G RAM
- 0xf0000000 -> 0xf1000000 16M NOR flashes (AXP GP / AXP DB)
- 0xf1000000 -> 0xf1100000 1M internal registers
- 0xf1100000 -> 0xf1110000 64KB Crypto SRAM #0 => OK !
- 0xf8000000 -> 0xffe0000 126M PCIe memory
- 0xffe00000 -> 0xfff00000 1M PCIe I/O
- 0xfff0000 -> 0xffffffff 1M BootROM
Obviously, the solution is to align the location of the Crypto SRAM
mappings of Armada XP to be similar with the ones on Armada 370, i.e
have them between the "internal registers" area and the beginning of
the PCIe aperture.
However, we have a special case with the OpenBlocks AX3-4 platform,
which has a 128 MB NOR flash. Currently, this NOR flash is mapped from
0xf0000000 to 0xf8000000. This is possible because on OpenBlocks
AX3-4, the internal registers are not at 0xf1000000. And this explains
why the Crypto SRAM mappings were not configured at the same place on
Armada XP.
Hence, the solution is two-fold:
(1) Move the NOR flash mapping on Armada XP OpenBlocks AX3-4 from
0xe8000000 to 0xf0000000. This frees the 0xf0000000 ->
0xf80000000 space.
(2) Move the Crypto SRAM mappings on Armada XP to be similar to
Armada 370 (except of course that Armada XP has two Crypto SRAM
and not one).
After this patch, the memory mapping on Armada XP boards with
registers at 0xf1 is:
- 0x00000000 -> 0xf0000000 3.75G RAM
- 0xf0000000 -> 0xf1000000 16M NOR flashes (AXP GP / AXP DB)
- 0xf1000000 -> 0xf1100000 1M internal registers
- 0xf1100000 -> 0xf1110000 64KB Crypto SRAM #0
- 0xf1110000 -> 0xf1120000 64KB Crypto SRAM #1
- 0xf8000000 -> 0xffe0000 126M PCIe memory
- 0xffe00000 -> 0xfff00000 1M PCIe I/O
- 0xfff0000 -> 0xffffffff 1M BootROM
And the memory mapping for the special case of the OpenBlocks AX3-4
(internal registers at 0xd0000000, NOR of 128 MB):
- 0x00000000 -> 0xc0000000 3G RAM
- 0xd0000000 -> 0xd1000000 1M internal registers
- 0xe800000 -> 0xf0000000 128M NOR flash
- 0xf1100000 -> 0xf1110000 64KB Crypto SRAM #0
- 0xf1110000 -> 0xf1120000 64KB Crypto SRAM #1
- 0xf8000000 -> 0xffe0000 126M PCIe memory
- 0xffe00000 -> 0xfff00000 1M PCIe I/O
- 0xfff0000 -> 0xffffffff 1M BootROM
Fixes: c466d997bb16 ("ARM: mvebu: define crypto SRAM ranges for all armada-xp boards")
Reported-by: Phil Sutter <phil@nwl.cc>
Cc: Phil Sutter <phil@nwl.cc>
Cc: <stable@vger.kernel.org>
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Acked-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
Signed-off-by: Olof Johansson <olof@lixom.net>
|
|
Linux 4.5-rc5
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/pjw/omap-pending into fixes
ARM: OMAP2+: critical DRA7xx fix for v4.5-rc
Force the DRA7xx Ethernet internal clock source to stay enabled
per TI erratum i877:
http://www.ti.com/lit/er/sprz429h/sprz429h.pdf
Otherwise, if the Ethernet internal clock source is disabled, the
chip will age prematurely, and the RGMII I/O timing will soon
fail to meet the delay time and skew specifications for 1000Mbps
Ethernet.
This fix should go in as soon as possible.
Basic build, boot, and PM test results are available here:
http://www.pwsan.com/omap/testlogs/omap-critical-fixes-for-v4.5-rc/20160307014209/
* tag 'for-v4.5-rc/omap-critical-fixes-a' of git://git.kernel.org/pub/scm/linux/kernel/git/pjw/omap-pending:
ARM: dts: dra7: do not gate cpsw clock due to errata i877
ARM: OMAP2+: hwmod: Introduce ti,no-idle dt property
Signed-off-by: Olof Johansson <olof@lixom.net>
|
|
Several cases of overlapping changes, as well as one instance
(vxlan) of a bug fix in 'net' overlapping with code movement
in 'net-next'.
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Errata id: i877
Description:
------------
The RGMII 1000 Mbps Transmit timing is based on the output clock
(rgmiin_txc) being driven relative to the rising edge of an internal
clock and the output control/data (rgmiin_txctl/txd) being driven relative
to the falling edge of an internal clock source. If the internal clock
source is allowed to be static low (i.e., disabled) for an extended period
of time then when the clock is actually enabled the timing delta between
the rising edge and falling edge can change over the lifetime of the
device. This can result in the device switching characteristics degrading
over time, and eventually failing to meet the Data Manual Delay Time/Skew
specs.
To maintain RGMII 1000 Mbps IO Timings, SW should minimize the
duration that the Ethernet internal clock source is disabled. Note that
the device reset state for the Ethernet clock is "disabled".
Other RGMII modes (10 Mbps, 100Mbps) are not affected
Workaround:
-----------
If the SoC Ethernet interface(s) are used in RGMII mode at 1000 Mbps,
SW should minimize the time the Ethernet internal clock source is disabled
to a maximum of 200 hours in a device life cycle. This is done by enabling
the clock as early as possible in IPL (QNX) or SPL/u-boot (Linux/Android)
by setting the register CM_GMAC_CLKSTCTRL[1:0]CLKTRCTRL = 0x2:SW_WKUP.
So, do not allow to gate the cpsw clocks using ti,no-idle property in
cpsw node assuming 1000 Mbps is being used all the time. If someone does
not need 1000 Mbps and wants to gate clocks to cpsw, this property needs
to be deleted in their respective board files.
Signed-off-by: Mugunthan V N <mugunthanvnm@ti.com>
Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com>
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: Paul Walmsley <paul@pwsan.com>
|
|
Add iio-hwmon node to expose the temperature channel on Vybrid as
hardware monitor device using the iio_hwmon driver.
Signed-off-by: Sanchayan Maity <maitysanchayan@gmail.com>
Acked-by: Stefan Agner <stefan@agner.ch>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
|
|
Change iio_hwmon nodes to use hypen in node names instead of
underscore.
Signed-off-by: Sanchayan Maity <maitysanchayan@gmail.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/horms/renesas into fixes
Merge "Second Round of Renesas ARM Based SoC DT Fixes for v4.5" from Simon Horman:
* remove enable prop from HS-USB device node on porter board
* tag 'renesas-dt-fixes2-for-v4.5' of git://git.kernel.org/pub/scm/linux/kernel/git/horms/renesas:
ARM: dts: porter: remove enable prop from HS-USB device node
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/chanwoo/extcon into char-misc-testing
Chanwoo writes:
Update extcon for 4.6
Detailed description for patchset:
1. Add new EXTCON_CHG_USB_SDP type
- SDP (Standard Downstream Port) USB Charging Port
means the charging connector.a
2. Add the VBUS detection by using GPIO on extcon-palmas
- Beaglex15 board uses the extcon-palmas driver
But, beaglex15 board need the GPIO support for VBUS
detection.
3. Fix the minor issue of extcon drivers
|
|
In the final versions of the Porter board (called "PORTER_C") Renesas
decided to get rid of the Maxim Integrated MAX3355 OTG chip and didn't
add any other provision to differ the host/gadget mode, so we'll have to
remove no longer valid "renesas,enable-gpio" property from the HS-USB
device node. Hopefully, the earlier revisions of the board were never
seen in the wild...
Fixes: c794f6a09a25 ("ARM: shmobile: porter: add HS-USB DT support")
Reported-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
|
|
Add the 1588 timer node for ls1021a platform to
support gianfar ptp driver.
Signed-off-by: Yangbo Lu <yangbo.lu@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap into fixes
Two omap fixes for omaps against v4.5-rc5:
- Yet another fix for n900 onenand to avoid corruption. This time to
fix the issue of mounting onenand back and forth between the original
maemo kernel and mainline Linux kernel. And it also seems there will
be two more fixes coming via the MTD tree as issues were discovered
also in the onenand driver during testing.
- Revert tps65217 regulator clean up as it breaks MMC for am335x
variants. The proper way to clean this up is just to rename the
tps65217.dtsi file into tps65217-am335x.dtsi as a similar setup
is used on many am335x boards.
* tag 'omap-for-v4.5/fixes-rc5' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap:
ARM: OMAP2+: Fix onenand initialization to avoid filesystem corruption
Revert "regulator: tps65217: remove tps65217.dtsi file"
Signed-off-by: Olof Johansson <olof@lixom.net>
|
|
PIN_PA15 macro has the same value as PIN_PA14 so we were overriding PA14
mux/configuration.
Signed-off-by: Ludovic Desroches <ludovic.desroches@atmel.com>
Reported-by: Cyrille Pitchen <cyrille.pitchen@atmel.com>
Fixes: 7f16cb676c00 ("ARM: at91/dt: add sama5d2 pinmux")
Cc: <stable@vger.kernel.org> # v4.4+
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
Signed-off-by: Olof Johansson <olof@lixom.net>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/shawnguo/linux into fixes
The i.MX fixes for v4.5:
- Drop the bogus interrupt-parent from i.MX6 CAAM node, which leads to
the CAAM IRQs not getting unmasked at the GPC level.
* tag 'imx-fixes-4.5' of git://git.kernel.org/pub/scm/linux/kernel/git/shawnguo/linux:
ARM: dts: imx6: remove bogus interrupt-parent from CAAM node
Signed-off-by: Olof Johansson <olof@lixom.net>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap into fixes
Few fixes for omaps against v4.5-rc3:
- Improve omap_device error message to tell driver writers what is
wrong after commit 5de85b9d57ab ("PM / runtime: Re-init runtime PM
states at probe error and driver unbind"). There will be also a
handful of driver related fixes also queued separately. But adding
this error message makes it easy to fix any omap_device using
drivers suffering from this issue so I think it's important to
have.
- Also related to commit 5de85b9d57ab discussion, let's fix a bug
where disabling PM runtime via sysfs will also cause the hardware
state to be different from PM runtime state.
- Fix audio clocks for beagle-x15.
- Use wakeup-source instead of gpio-key,wakeup for the new entries
that sneaked in during the merge window.
- Fix a legacy booting vs device tree based booting regression for
n900 where the legacy user space expects to have the device
revision available in /proc/atags also when booted with device
tree.
* tag 'omap-for-v4.5/fixes-rc3-v2' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap:
ARM: OMAP2+: Fix omap_device for module reload on PM runtime forbid
ARM: OMAP2+: Improve omap_device error for driver writers
ARM: DTS: am57xx-beagle-x15: Select SYS_CLK2 for audio clocks
ARM: dts: am335x/am57xx: replace gpio-key,wakeup with wakeup-source property
ARM: OMAP2+: Set system_rev from ATAGS for n900
Signed-off-by: Olof Johansson <olof@lixom.net>
|
|
mvebu fixes for 4.5 (part 2)
- Fix the missing mtd flash on linkstation lswtgl
- Use unique machine name for the kirkwood ds112 (for Debian flash-kernel tool)
* tag 'mvebu-fixes-4.5-2' of git://git.infradead.org/linux-mvebu:
ARM: dts: orion5x: fix the missing mtd flash on linkstation lswtgl
ARM: dts: kirkwood: use unique machine name for ds112
Signed-off-by: Olof Johansson <olof@lixom.net>
|
|
This change does not break existing userspace or Maemo software because
isp1704_charger.c always export power supply device under isp1704 name.
Signed-off-by: Pali Rohár <pali.rohar@gmail.com>
Acked-by: Pavel Machek <pavel@ucw.cz>
Acked-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Sebastian Reichel <sre@kernel.org>
|
|
This reverts commit 8e6ebfaa9b384088002baa10f7534efa73a0794e.
Without the patch reverted regulators will not work. This prevents
MMC to be working for example so the boards can not boot to
MMC rootfs.
Tested it on beaglebone white and bisect also points to the
reverted commit.
The issue can be also fixed by adding "regulator-compatible =" to all board
dts file for the regulators.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
|
Add the device tree entries and bindings needed to support the Altera L2
cache and On-Chip RAM EDAC. This patch relies upon an earlier patch to
declare and setup On-chip RAM properly:
8b907c8b62ac ("arm: dts: socfpga: Add OCRAM node")
Signed-off-by: Thor Thayer <tthayer@opensource.altera.com>
Acked-by: Rob Herring <robh@kernel.org>
Cc: devicetree@vger.kernel.org
Cc: Dinh Nguyen <dinguyen@opensource.altera.com>
Cc: galak@codeaurora.org
Cc: grant.likely@linaro.org
Cc: Ian Campbell <ijc+devicetree@hellion.org.uk>
Cc: ijc+devicetree@hellion.org.uk
Cc: Kumar Gala <galak@codeaurora.org>
Cc: linux-arm-kernel@lists.infradead.org
Cc: linux@arm.linux.org.uk
Cc: linux-doc@vger.kernel.org
Cc: linux-edac <linux-edac@vger.kernel.org>
Cc: Mark Rutland <mark.rutland@arm.com>
Cc: m.chehab@samsung.com
Cc: Pawel Moll <pawel.moll@arm.com>
Cc: Rob Herring <robh+dt@kernel.org>
Cc: Russell King <linux@arm.linux.org.uk>
Link: http://lkml.kernel.org/r/1455132384-17108-2-git-send-email-tthayer@opensource.altera.com
Signed-off-by: Borislav Petkov <bp@suse.de>
|
|
The tlv320aic3104 codec's master clock is coming from the SoC's CLKOUT2.
Select the SYS_CLK2 (via divider) as parent clock for CLKOUT2 and select
the same clock (SYS_CLK2) for McASP3 AHCLKX clock as well.
SYS_CLK2 is sourced from an external oscillator running 22.5792MHz and it
is coming in to the SoC via the X1_OSC1.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
|
Commit 3efda00129bd ("ARM: dts: am335x: replace gpio-key,wakeup with
wakeup-source property") replaces all the legacy "gpio-key,wakeup" with
the unified "wakeup-source" property to prevent any further copy-paste
duplication.
However couple of use of these legacy property sneaked in during the
merge window. This patch replaces them too.
Cc: "Benoît Cousson" <bcousson@baylibre.com>
Cc: linux-omap@vger.kernel.org
Signed-off-by: Sudeep Holla <sudeep.holla@arm.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
|
MTD flash stores u-boot and u-boot environment on linkstation lswtgl.
The latter one can be easily read/write by u-boot-tools package in Debian.
Fixes: dc57844a736f ("ARM: dts: orion5x: add buffalo linkstation ls-wtgl")
Signed-off-by: Roger Shimizu <rogershimizu@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
|
|
Downstream packages like Debian flash-kernel use
/proc/device-tree/model
to determine which dtb file to install.
Hence each dts in the Linux kernel should provide a unique model
identifier.
Commit 2d0a7addbd10 ("ARM: Kirkwood: Add support for many Synology NAS
devices") created the new files kirkwood-ds111.dts and kirkwood-ds112.dts
using the same model identifier.
This patch provides a unique model identifier for the
Synology DiskStation DS112.
Fixes: 2d0a7addbd10 ("ARM: Kirkwood: Add support for many Synology NAS devices")
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
|
|
According to latest schematics [1], GPIO_1/VBUSDET
on TPS659038 is tied to AM57x GPIO4_21. We can use
that as a VBUS interrupt, instead of relying on
PMIC's VBUS interrupts which don't seem to be firing
on x15 at all.
A follow up patch will add support for using this
GPIO-based interrupt mechanism for notifying about
VBUS.
[1] https://github.com/beagleboard/beagleboard-x15/blob/master/BeagleBoard-X15_RevA2.pdf
Signed-off-by: Felipe Balbi <balbi@ti.com>
[cw00.choi: Use the 'vbus-gpio' property instead of 'interrupts-extended']
Signed-off-by: Chanwoo Choi <cw00.choi@samsung.com>
Acked-by: Tony Lindgren <tony@atomide.com>
|
|
According to latest schematics [1], this board
leaves ID pin floating. It's not connected to
anything at all.
So let's remove it.
[1] https://github.com/beagleboard/beagleboard-x15/blob/master/BeagleBoard-X15_RevA2.pdf
Signed-off-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Chanwoo Choi <cw00.choi@samsung.com>
Acked-by: Tony Lindgren <tony@atomide.com>
|
|
The DTSI file for the Nomadik does not properly specify how the
PL180 levelshifter is connected: the Nomadik actually needs all
the five st,sig-dir-* flags set to properly control all lines out.
Further this board supports full power cycling of the card, and
since this variant has no hardware clock gating, it needs a
ridiculously low frequency setting to keep up with the ever
overflowing FIFO.
The pin configuration set-up is a bit of a mystery, because of
course these pins are a mix of inputs and outputs. However the
reference implementation sets all pins to "output" with
unspecified initial value, so let's do that here as well.
Cc: stable@vger.kernel.org
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Acked-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Olof Johansson <olof@lixom.net>
|
|
mvebu fixes for 4.5 (part 1)
- Fix dts on buffalo linksations machines (gpios and leds)
- Fix dts partition node according to new binding introduced in v4.5
* tag 'mvebu-fixes-4.5-1' of git://git.infradead.org/linux-mvebu:
ARM: dts: orion5x: gpio pin fixes for linkstation lswtgl
ARM: dts: kirkwood: gpio-leds fixes for linkstation ls-wvl/vl
ARM: dts: kirkwood: gpio-leds fixes for linkstation ls-wxl/wsxl
ARM: dts: kirkwood: gpio pin fixes for linkstation ls-wvl/vl
ARM: dts: kirkwood: gpio pin fixes for linkstation ls-wxl/wsxl
ARM: mvebu: ix4-300d: Add compatible property to "partitions" node
ARM: mvebu: kirkwood: Add compatible property to "partitions" node
Signed-off-by: Olof Johansson <olof@lixom.net>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap into fixes
Fixes for omaps with the most intrusive stuff being read-only data
assembly fixes, the other things are mostly board related:
- A series of omap assembly code fixes to fix issues with rodata with
ARM_KERNMEM_PERMS enabled. We had several places writing to rodata,
which is bad. The fix in most cases is to load the value from data
section using a pointer. Let's also enable ARM_KERNMEM_PERMS so
DEBUG_RODATA gets selected by default. And while testing things,
I also added few more loadable driver modules to the defconfig that
I seem to need quite often.
- Fix a long standing omap5 RTC mystery and enable RTC where we need
to ensure the SoC msecure pin is high so we can write to the RTC
registers.
- Fix irq types for am437x
- A series of minor dts fixes for sbc-am57x and cl-som-am57x
- Fixes for torpedo dts to make WLAN behave and to remove a duplicate
i2c rate entry
This series also includes few minor changes that are not stricly
fixes, but would be good to get in during the early -rc cycle:
- Remove legacy mailbox platform data that is no longer needed
- Add the pdata-quirks needed for the new pwm-omap-dmtimer so
people can use it
- Enable ti,mbox-send-noirq that's needed by wkup_m3 driver
- Enable SPLIT and DWARF4 in omap2plus_defconfig as it makes the
initramfs quite a bit smaller
* tag 'omap-for-v4.5/fixes-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap: (23 commits)
ARM: dts: am57xx: sbc-am57x: correct Eth PHY settings
ARM: dts: am57xx: cl-som-am57x: fix CPSW EMAC pinmux
ARM: dts: am57xx: sbc-am57x: fix UART3 pinmux
ARM: dts: am57xx: cl-som-am57x: update SPI Flash frequency
ARM: dts: am57xx: cl-som-am57x: set HOST mode for USB2
ARM: dts: am57xx: sbc-am57x: fix SB-SOM EEPROM I2C address
ARM: dts: LogicPD Torpedo: Revert Duplicative Entries
ARM: dts: am437x: pixcir_tangoc: use correct flags for irq types
ARM: dts: am4372: fix irq type for arm twd and global timer
ARM: dts: Fix wl12xx missing clocks that cause hangs
ARM: OMAP: Add PWM dmtimer platform data quirks
ARM: omap2plus_defconfig: Enable ARM_KERNMEM_PERMS and few loadable modules
ARM: OMAP2+: Fix ppa_zero_params and ppa_por_params for rodata
ARM: OMAP2+: Fix l2_inv_api_params for rodata
ARM: OMAP2+: Fix save_secure_ram_context for rodata
ARM: OMAP2+: Fix l2dis_3630 for rodata
ARM: OMAP2+: Fix wait_dll_lock_timed for rodata
ARM: OMAP2+: Remove legacy mailbox device instantiation
ARM: dts: AM4372: Add ti,mbox-send-noirq to wkup_m3 mailbox
ARM: dts: AM33xx: Add ti,mbox-send-noirq to wkup_m3 mailbox
...
Signed-off-by: Olof Johansson <olof@lixom.net>
|
|
Add pinfunc header file, mt2701 related dts will include it
Signed-off-by: Biao Huang <biao.huang@mediatek.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
The interrupt-parent property is not needed as it is inherited from
the parent bus and in the case of the CAAM node actively points to
the wrong interrupt controller (GIC instead of GPC). This leads to
the CAAM IRQs not getting unmasked at the GPC level, leaving them
unable to wake the CPU from wait mode, potentially impacting
performance of the CAAM unit when CPUidle is enabled.
Signed-off-by: Lucas Stach <l.stach@pengutronix.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
Update Eth PHY settings to make it possible to run both phys at 1Gbps.
Signed-off-by: Dmitry Lifshitz <lifshitz@compulab.co.il>
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
|
Fix CPSW EMAC pinmux
Signed-off-by: Dmitry Lifshitz <lifshitz@compulab.co.il>
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
|
Fix UART3 pinmux.
Signed-off-by: Dmitry Lifshitz <lifshitz@compulab.co.il>
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
|
On-board SPI flash cat act at 48Mhz SPI bus frequency.
Update the DT frequency property.
Signed-off-by: Dmitry Lifshitz <lifshitz@compulab.co.il>
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
|
Setup USB2 to act in "HOST" mode by default.
Signed-off-by: Dmitry Lifshitz <lifshitz@compulab.co.il>
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
|
Fix SB-SOM EEPROM I2C address
Signed-off-by: Dmitry Lifshitz <lifshitz@compulab.co.il>
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
|
Revert commit 7cd6ca770d1b ("ARM: dts: Change I2C2 and I2C3 to 400KHz
for LogicPD Torpedo DM3730 devkit") It was already done and it is
just a duplicate.
Signed-off-by: Adam Ford <aford173@gmail.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
|
Now IRQs for Pixcir Tangoc touchscreen are defined using
IRQ_TYPE_NONE in am437x-gp-evm.dts and am43x-epos-evm.dts wich
do not correspond HW.
Hence, update am437x-gp-evm.dts and am43x-epos-evm.dts files
and use correct flag IRQ_TYPE_EDGE_FALLING for irq types.
While here, remove duplicated irq declaration for pixcir_ts@5c node
in am437x-gp-evm.dts.
Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
