| Age | Commit message (Collapse) | Author |
|---|
|
https://git.kernel.org/pub/scm/linux/kernel/git/mripard/linux into fixes
Allwinner fixes for 4.0
There's a few fixes to merge for 4.0, one to add a select in the machine
Kconfig option to fix a potential build failure, and two fixing cpufreq related
issues.
* tag 'sunxi-fixes-for-4.0' of https://git.kernel.org/pub/scm/linux/kernel/git/mripard/linux:
ARM: dts: sunxi: Remove overclocked/overvoltaged OPP
ARM: dts: sun4i: a10-lime: Override and remove 1008MHz OPP setting
ARM: sunxi: Have ARCH_SUNXI select RESET_CONTROLLER for clock driver usage
Signed-off-by: Olof Johansson <olof@lixom.net>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap into fixes
Fixes for omaps for the -rc cycle:
- Fix a device tree based booting vs legacy booting regression for
omap3 crypto hardware by adding the missing DMA channels.
- Fix /sys/bus/soc/devices/soc0/family for am33xx devices.
- Fix two timer issues that can cause hangs if the timer related
hwmod data is missing like it often initially is for new SoCs.
- Remove pcie hwmods entry from dts as that causes runtime PM to
fail for the PHYs.
- A paper bag type dts configuration fix for dm816x GPIO
interrupts that I just noticed. This is most of the changes
diffstat wise, but as it's a basic feature for connecting
devices and things work otherwise, it should be fixed.
* tag 'fixes-v4.0-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap:
ARM: dts: Fix gpio interrupts for dm816x
ARM: dts: dra7: remove ti,hwmod property from pcie phy
ARM: OMAP: dmtimer: disable pm runtime on remove
ARM: OMAP: dmtimer: check for pm_runtime_get_sync() failure
ARM: OMAP2+: Fix socbus family info for AM33xx devices
ARM: dts: omap3: Add missing dmas for crypto
Signed-off-by: Olof Johansson <olof@lixom.net>
|
|
git://git.rocketboards.org/linux-socfpga-next into fixes
Late fix for v4.0 on the SoCFPGA platform:
- Fix interrupt number for SPI1 interface
* tag 'socfpga_fix_for_v4.0_2' of git://git.rocketboards.org/linux-socfpga-next:
ARM: socfpga: dts: fix spi1 interrupt
Signed-off-by: Olof Johansson <olof@lixom.net>
|
|
Without proper regulator support for individual boards, it is dangerous
to have overclocked/overvoltaged OPPs in the list. Cpufreq will increase
the frequency without the accompanying voltage increase, resulting in
an unstable system.
Remove them for now. We can revisit them with the new version of OPP
bindings, which support boost settings and frequency ranges, among
other things.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
|
|
The Olimex A10-Lime is known to be unstable when running at 1008MHz.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
|
|
The socfpga.dtsi currently has the wrong interrupt number set for SPI master 1
Trying to use the master without this change results in the kernel boot
process waiting forever for an interrupt that will never occur while
attempting to probe any slave devices configured in the device tree as being
under SPI master 1.
The change works for the Cyclone V, and according to the Arria 5 handbook
should be good there too.
Signed-off-by: Mark James <maj@jamers.net>
Acked-by: Steffen Trumtrar <s.trumtrar@pengutronix.de>
Signed-off-by: Dinh Nguyen <dinguyen@opensource.altera.com>
|
|
Commit 7800064ba507 ("ARM: dts: Add basic dm816x device tree
configuration") added basic devices for dm816x, but I was not able
to test the GPIO interrupts earlier until I found some suitable pins
to test with. We can mux the MMC card detect and write protect pins
from SD_SDCD and SD_SDWP mode to use a normal GPIO interrupts that
are also suitable for the MMC subsystem.
This turned out several issues that need to be fixed:
- I set the GPIO type wrong to be compatible with omap3 instead
of omap4. The GPIO controller on dm816x has EOI interrupt
register like omap4 and am335x.
- I got the GPIO interrupt numbers wrong as each bank has two
and we only use one. They need to be set up the same way as
on am335x.
- The gpio banks are missing interrupt controller related
properties.
With these changes the GPIO interrupts can be used with the
MMC card detect pin, so let's wire that up. Let's also mux all
the MMC lines for completeness while at it.
For the first GPIO bank I tested using GPMC lines temporarily
muxed to GPIOs on the dip switch 10.
Cc: Brian Hutchinson <b.hutchman@gmail.com>
Cc: Matthijs van Duin <matthijsvanduin@gmail.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
|
Now that we don't have hwmod entry for pcie PHY remove the
ti,hwmod property from PCIE PHY's. Otherwise we will get:
platform 4a094000.pciephy: Cannot lookup hwmod 'pcie1-phy'
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
[tony@atomide.com: updated comments]
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
|
This patch adds missing dma DTS definitions for omap aes and sham drivers.
Without it kernel drivers do not work for device tree based booting
while it works for legacy booting on general purpose SoCs.
Note that further changes are still needed for high secure SoCs. But since
that never worked in legacy boot mode either, those will be sent separately.
Signed-off-by: Pali Rohár <pali.rohar@gmail.com>
Acked-by: Pavel Machek <pavel@ucw.cz>
[tony@atomide.com: updated comments]
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/mmind/linux-rockchip into fixes
Pull "ARM: rockchip: small fixes for 4.0-rc" from Heiko Stuebner:
Adding a default-disabled state to the new gmac node and an
update to the MAINTAINERS entry adding a rockchip regexp entry.
* tag 'v4.0-rockchip-armfixes1' of git://git.kernel.org/pub/scm/linux/kernel/git/mmind/linux-rockchip:
ARM: dts: rockchip: disable gmac by default in rk3288.dtsi
MAINTAINERS: add rockchip regexp to the ARM/Rockchip entry
|
|
This block should not be enabled by default or else if the kconfig is set,
it will try to load/probe even if there's no phy connected.
Signed-off-by: Alexandru M Stan <amstan@chromium.org>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/nferre/linux-at91 into fixes
Pull "Third fixes batch for AT91 on 4.0" from Nicolas Ferre:
- clock fixes for USB
- compatible string changes for handling USB IP differences
(+ needed AHB matrix syscon)
- fix of a compilation error in PM code
* tag 'at91-fixes3' of git://git.kernel.org/pub/scm/linux/kernel/git/nferre/linux-at91:
ARM: at91: pm_slowclock: fix the compilation error
ARM: at91/dt: fix USB high-speed clock to select UTMI
ARM: at91/dt: fix at91 udc compatible strings
ARM: at91/dt: declare matrix node as a syscon device
ARM: at91/dt: at91sam9261: fix clocks and clock-names in udc definition
|
|
The UTMI clock must be selected by any high-speed USB IP. The logic behind it
needs this particular clock.
So, correct the clock in the device tree files affected.
Reported-by: Bo Shen <voice.shen@atmel.com>
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Cc: <stable@vger.kernel.org> #3.18
|
|
The at91rm9200, at91sam9260, at91sam9261 and at91sam9263 SoCs have slightly
different UDC IPs.
Those differences were previously handled with cpu_is_at91xx macro which
are about to be dropped for multi-platform support, thus we need to
change compatible strings.
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
|
|
There is no specific driver handling the AHB matrix, this is a simple syscon
device. the matrix is needed by several other drivers including the USB on some
SoCs (at91sam9261 for instance).
Without this definition, the USB will not work on these SoCs.
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/shawnguo/linux into fixes
Pull "The i.MX fixes for 4.0" from Shawn Guo:
It includes a couple of i.MX6 dts fixes, which set an input supply to
vbus regulator. Without the fixes, the voltage of vbus is incorrect
after system boots up.
* tag 'imx-fixes-4.0' of git://git.kernel.org/pub/scm/linux/kernel/git/shawnguo/linux:
ARM: imx6sl-evk: set swbst_reg as vbus's parent reg
ARM: imx6qdl-sabresd: set swbst_reg as vbus's parent reg
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap into fixes
Pull "omap fixes against v4.0-rc2" from Tony Lindgren:
Fixes for various omap variants, mostly minor fixes for various SoCs
with the bigger changes being for the dra7 clocks and hwmod data:
- Fix wl12xx for dm3730-evm
- Fix omap4 prm save and clea
- Fix hwmod clkdm use count
- Fix hwmod data for pcie on dra7
- Fix lockdep for hwmod
- Fix USB on most omap3 boars by enabling it in the defconfig
- Fix the bypass clock source for omap5 and dra7
- Fix the ehrpwm clock for am33xx and am43xx
- Enable AES and SHAM for BeagleBone white
- Use rmii clock for am335x-lxm
- Fix polling intervals for omap5 thermal zones
- Fix slewctrl for am33xx and am43xx
- Fix dra7-evm dcan pinctrl
* tag 'fixes-v4.0-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap:
ARM: OMAP2+: Fix wl12xx on dm3730-evm with mainline u-boot
ARM: OMAP: enable TWL4030_USB in omap2plus_defconfig
ARM: dts: dra7x-evm: avoid possible contention while muxing on CAN lines
ARM: dts: dra7x-evm: Don't use dcan1_rx.gpio1_15 in DCAN pinctrl
ARM: dts: am43xx: fix SLEWCTRL_FAST pinctrl binding
ARM: dts: am33xx: fix SLEWCTRL_FAST pinctrl binding
ARM: dts: OMAP5: fix polling intervals for thermal zones
ARM: dts: am335x-lxm: Use rmii-clock-ext
ARM: dts: am335x-bone-common: enable aes and sham
ARM: dts: am43xx-clocks: Fix ehrpwm tbclk data on am43xx
ARM: dts: am33xx-clocks: Fix ehrpwm tbclk data on am33xx
ARM: dts: OMAP5: Fix the bypass clock source for dpll_iva and others
ARM: dts: DRA7x: Fix the bypass clock source for dpll_iva and others
ARM: OMAP4+: PRM: fix omap4 version of prm_save_and_clear_irqen
ARM: OMAP2+: hwmod: fix deassert hardreset clkdm usecounting
ARM: DRA7: hwmod_data: Fix hwmod data for pcie
ARM: omap2+: omap_hwmod: Set unique lock_class_key per hwmod
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/nferre/linux-at91 into fixes
Pull "Second fixes batch for AT91 on 4.0" from Nicolas Ferre:
- little fix for !MMU debug: may also help for randconfig
- fix of 2 errors in LCD clock definitions
- in PM code, not writing the key leads to not execute the action
* tag 'at91-fixes2' of git://git.kernel.org/pub/scm/linux/kernel/git/nferre/linux-at91:
ARM: at91/pm: MOR register KEY was missing
ARM: at91/dt: sama5d4: fix lcdck clock definition
ARM: at91/dt: sama5d4: rename lcd_clk into lcdc_clk
ARM: at91: debug: fix non MMU debug
|
|
git://git.rocketboards.org/linux-socfpga-next into fixes
Pull "Fixes for v4.0 on the SoCFPGA platform" from Dinh Nguyen:
- Fix the SCU virtual mapping
- Add misssing DMA channels for UART nodes
- Fix a sporadic SMP error where CPU1 was not seeing its start address
* tag 'socfpga_fixes_for_v4.0' of git://git.rocketboards.org/linux-socfpga-next:
ARM: socfpga: make sure socfpga_cpu1start_addr is properly flushed
ARM: socfpga: fix uart DMA binding error
ARM: socfpga: Correct SCU virtual mapping in socfpga
|
|
USB vbus 5V is from PMIC SWBST, so set swbst_reg as vbus's
parent reg, it fixed a bug that the voltage of vbus is incorrect
due to swbst_reg is disabled after boots up.
Cc: stable@vger.kernel.org
Signed-off-by: Peter Chen <peter.chen@freescale.com>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
|
|
USB vbus 5V is from PMIC SWBST, so set swbst_reg as vbus's
parent reg, it fixed a bug that the voltage of vbus is incorrect
due to swbst_reg is disabled after boots up.
Cc: stable@vger.kernel.org
Signed-off-by: Peter Chen <peter.chen@freescale.com>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
|
|
Peripheral clock is named pclk and system clock is named hclk (those are
the names expected by the at91_udc driver).
Drop the deprecated usb_clk (formerly used to configure the usb clock rate
which is now directly configurable through hclk).
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
|
|
DCAN1 RX and TX lines are internally pulled high according to [1].
While muxing between DCAN mode and SAFE mode we make sure
that the same pull direction is set to minimize opposite
pull contention during the switching window.
[1] in DRA7 data manual, Ball characteristics table 4-2, DSIS colum shows
the state driven to the peripheral input while in the deselcted mode.
DSIS - De-Selected Input State.
Signed-off-by: Roger Quadros <rogerq@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
|
Rev.F onwards ball G19 (dcan1_rx) is used as a GPIO for some other
function so don't include it in DCAN pinctrl node.
Signed-off-by: Roger Quadros <rogerq@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
|
OMAP4 has a finer counter granularity, which allows for a delay of 1000ms
in the thermal zone polling intervals. OMAP5 has a different counter
mechanism, which allows at maximum a 500ms timer. Adjust the cpu thermal
zone polling interval accordingly.
Without this patch, the polling interval information is simply ignored,
and the following thermal warnings are printed during boot (assuming
thermal is enabled);
[ 1.545343] ti-soc-thermal 4a0021e0.bandgap: Delay 1000 ms is not supported
[ 1.552691] ti-soc-thermal 4a0021e0.bandgap: Delay 1000 ms is not supported
[ 1.560029] ti-soc-thermal 4a0021e0.bandgap: Delay 1000 ms is not supported
Signed-off-by: Tero Kristo <t-kristo@ti.com>
Cc: Tony Lindgren <tony@atomide.com>
Acked-by: Eduardo Valentin <edubezval@gmail.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
|
Use external clock for RMII since the internal clock doesn't meet the
jitter requirements.
Signed-off-by: George McCollister <george.mccollister@gmail.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
|
Beaglebone Black doesn't have AES and SHAM enabled like the
original Beaglebone White dts. This breaks applications that
leverage the crypto blocks so fix this by enabling these nodes
in the am335x-bone-common.dtsi. With this change, enabling the
nodes in am335x-bone.dts is no longer required so remove them.
Signed-off-by: Matt Porter <mporter@konsulko.com>
Acked-by: Robert Nelson <robertcnelson@gmail.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
|
ehrpwm tbclk is wrongly modelled as deriving from dpll_per_m2_ck.
The TRM says tbclk is derived from SYSCLKOUT. SYSCLKOUT nothing but the
functional clock of pwmss (l4ls_gclk).
Fix this by changing source of ehrpwmx_tbclk to l4ls_gclk.
Fixes: 4da1c67719f61 ("add tbclk data for ehrpwm")
Signed-off-by: Vignesh R <vigneshr@ti.com>
Acked-by: Tero Kristo <t-kristo@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
|
ehrpwm tbclk is wrongly modelled as deriving from dpll_per_m2_ck.
The TRM says tbclk is derived from SYSCLKOUT. SYSCLKOUT nothing but the
functional clock of pwmss (l4ls_gclk).
Fix this by changing source of ehrpwmx_tbclk to l4ls_gclk.
Fixes: 9e100ebafb91: ("Fix ehrpwm tbclk data")
Signed-off-by: Vignesh R <vigneshr@ti.com>
Acked-by: Tero Kristo <t-kristo@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
|
Fixes 85dc74e9 (ARM: dts: omap5 clock data)
On OMAP54xx, For DPLL_IVA, the ref clock(CLKINP) is connected to sys_clk1 and
the bypass input(CLKINPULOW) is connected to iva_dpll_hs_clk_div clock.
But the bypass input is not directly routed to bypass clkout instead
both CLKINP and CLKINPULOW are connected to bypass clkout via a mux.
This mux is controlled by the bit - CM_CLKSEL_DPLL_IVA[23]:DPLL_BYP_CLKSEL
and it's POR value is zero which selects the CLKINP as bypass clkout.
which means iva_dpll_hs_clk_div is not the bypass clock for dpll_iva_ck
Fix this by adding another mux clock as parent in bypass mode.
This design is common to most of the PLLs and the rest have only one bypass
clock. Below is a list of the DPLLs that need this fix:
DPLL_IVA,
DPLL_PER,
DPLL_USB and DPLL_CORE
Signed-off-by: Ravikumar Kattekola <rk@ti.com>
Acked-by: Tero Kristo <t-kristo@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
|
Fixes: ee6c750761 (ARM: dts: dra7 clock data)
On DRA7x, For DPLL_IVA, the ref clock(CLKINP) is connected to sys_clk1 and
the bypass input(CLKINPULOW) is connected to iva_dpll_hs_clk_div clock.
But the bypass input is not directly routed to bypass clkout instead
both CLKINP and CLKINPULOW are connected to bypass clkout via a mux.
This mux is controlled by the bit - CM_CLKSEL_DPLL_IVA[23]:DPLL_BYP_CLKSEL
and it's POR value is zero which selects the CLKINP as bypass clkout.
which means iva_dpll_hs_clk_div is not the bypass clock for dpll_iva_ck
Fix this by adding another mux clock as parent in bypass mode.
This design is common to most of the PLLs and the rest have only one bypass
clock. Below is a list of the DPLLs that need this fix:
DPLL_IVA, DPLL_DDR,
DPLL_DSP, DPLL_EVE,
DPLL_GMAC, DPLL_PER,
DPLL_USB and DPLL_CORE
Signed-off-by: Ravikumar Kattekola <rk@ti.com>
Acked-by: Tero Kristo <t-kristo@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
|
lcdck takes mck (not smd) as its parent. It is also assigned id 3 and not 4.
Signed-off-by: Boris BREZILLON <boris.brezillon@free-electrons.com>
[nicolas.ferre@atmel.com: squashed 2 related patches]
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
|
|
Rename lcd_clk into lcdc_clk to be consistent with sama5d3 clock
definitions.
Signed-off-by: Boris BREZILLON <boris.brezillon@free-electrons.com>
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/nferre/linux-at91 into fixes
Merge "First fixes batch for AT91 on 4.0" from Nicolas Ferre:
- PM slowclock fixes for DDR and timeouts
- fix some DT entries
- little defconfig updates
- the removal of a harmful watchdog option + its detailed documentation
* tag 'at91-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/nferre/linux-at91:
ARM: at91/dt: keep watchdog running in idle mode
dts: Documentation: AT91 Watchdog, explain what atmel,idle-halt property really do
ARM: at91/defconfig: add at91rm9200 ethernet support
ARM: at91/defconfig: remove CONFIG_SYSFS_DEPRECATED
ARM: at91/dt: at91sam9260: fix usart pinctrl
ARM: at91/dt: sama5d4: add missing alias for i2c0
ARM: at91/dt: at91sam9263: Fixup sram1 device tree node
ARM: at91: pm: fix SRAM allocation
ARM: at91: pm: fix at91rm9200 standby
pm: at91: Workaround DDRSDRC self-refresh bug with LPDDR1 memories.
pm: at91: pm_slowclock: fix suspend/resume hang up in timeouts
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/kgene/linux-samsung into fixes
Merge "Samsung tmu and hdmi regression fixes for v4.0" from Kukjin Kim:
- The thermal management unit and HDMI (drm mixer driver) related
reworks have been merged in v4.0 merge window. So if this DT changes
are missed for v4.0, we regressions in v4.0 release for exynos
platforms such as exynos5250, exynos5420, exynos4 SoCs.
- Note since there was a dependency with driver side, this cannot
be sent to upstream during preivous merge window and now it has been
resolved.
* tag 'samsung-fixes-dt' of git://git.kernel.org/pub/scm/linux/kernel/git/kgene/linux-samsung:
ARM: dts: add display power domain for exynos5250
ARM: dts: add 'hdmi' clock to mixer nodes for exynos5250 and exynos5420
ARM: dts: enable hdmi support for exynos4210-universal_c210
ARM: dts: enable hdmi support for exynos4412-odroid-common
ARM: dts: add dependency between TV and LCD0 power domains for exynos4
ARM: dts: add hdmi related nodes for exynos4 SoCs
ARM: EXYNOS: add support for sub-power domains
dt-bindings: document a note about power domain subdomains
ARM: dts: Provide dt bindings identical for Exynos TMU
ARM: dts: Trip points and sensor configuration data for exynos5440
ARM: dts: define default thermal-zones for exynos4
ARM: dts: default trip points definition for exynos5420
ARM: dts: add TMU default definitions for exynos4412
ARM: dts: Adding CPU cooling binding for Exynos SoCs
ARM: dts: Enable TMU for exynos4412-odriod-common
ARM: dts: Add LDO10 for TMU for exynos4412-odroid-common
ARM: dts: Enable TMU for exynos4210-trats
|
|
socfpga.dtsi is missing the DMA channels for the uart nodes.
This will produce the following errors:
of_dma_request_slave_channel: dma-names property of node '/soc/serial0@ffc02000' missing or empty
ttyS0 - failed to request DMA
Provide the correct DMA channels to fix this.
Signed-off-by: Steffen Trumtrar <s.trumtrar@pengutronix.de>
Signed-off-by: Dinh Nguyen <dinguyen@opensource.altera.com>
|
|
Since turning on idle-halt in commit fe46aa679f12 (ARM: at91/dt: add
sam9 watchdog default options to SoCs), SoCs compatible with at91sam9260-wdt
no longer reboot if the watchdog times out while the CPU is in idle state.
Removing the 'idle-halt' flag that was set by default fixes this.
Signed-off-by: Michel Marti <mma@objectxp.com>
Acked-by: Boris Brezillon <boris.brezillon@free-electrons.com>
Acked-by: Sylvain Rochet <sylvain.rochet@finsecur.com>
[nicolas.ferre@atmel.com: rework the commit message]
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
|
|
Corrected pins used by usart3.
Signed-off-by: Jonas Andersson <jonas@microbit.se>
Acked-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
|
|
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
|
|
Commit ff04660e48b20 ("ARM: at91/dt: add SRAM nodes") used the same base
address for sram0 and sram1 leading to the following warning:
WARNING: CPU: 0 PID: 1 at fs/sysfs/dir.c:31 sysfs_warn_dup+0x50/0x70()
sysfs: cannot create duplicate filename '/devices/platform/300000.sram'
Fix the base address for sram1.
Signed-off-by: Alexander Stein <alexanders83@web.de>
Acked-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
|
|
The patch adds domain definition and references to it in appropriate devices.
Signed-off-by: Andrzej Hajda <a.hajda@samsung.com>
[mszyprow: rebased onto generic power domains dt bindings]
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Tested-by: Javier Martinez Canillas <javier.martinez@collabora.co.uk>
Reviewed-by: Javier Martinez Canillas <javier.martinez@collabora.co.uk>
Signed-off-by: Kukjin Kim <kgene@kernel.org>
|
|
Mixed block needs to control hdmi clock to properly perform power on/off
operation, so add 'hdmi' clock also to mixer nodes.
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Kukjin Kim <kgene@kernel.org>
|
|
This patch adds configuration of hw modules required to enable HDMI
support on Universal C210 board.
Signed-off-by: Tomasz Stanislawski <t.stanislaws@samsung.com>
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Kukjin Kim <kgene@kernel.org>
|
|
This patch adds nodes specific to Exynos4412 based Odroid X/X2/U2/U3
boards required for enabling HDMI display.
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Kukjin Kim <kgene@kernel.org>
|
|
TV Mixer needs both TV and LCD0 domains enabled to be fully operational.
This dependency is modelled by making TV power domains a sub-domain of
LCD0 power domain.
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Kukjin Kim <kgene@kernel.org>
|
|
This patch adds entries for HDMI, Mixer and i2c with hdmi-phy modules
found in Exynos 4210 and 4x12 SoCs.
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Kukjin Kim <kgene@kernel.org>
|
|
Presented device tree bindings provide data already hardcoded in the
exynos_tmu_data.c file.
After this commit, it should be possible to reuse common thermal core
framework in Exynos SoCs.
Signed-off-by: Lukasz Majewski <l.majewski@samsung.com>
Acked-by: Eduardo Valentin <edubezval@gmail.com>
Signed-off-by: Kukjin Kim <kgene@kernel.org>
|
|
This commit provides information about Exynos5440 device configuration.
Previously this information was available in exynos_tmu_data.c file.
Now it is available in the device tree.
Such approach allows reusing some common code for thermal.
Signed-off-by: Lukasz Majewski <l.majewski@samsung.com>
Acked-by: Eduardo Valentin <edubezval@gmail.com>
Signed-off-by: Kukjin Kim <kgene@kernel.org>
|
|
Trip points corresponding to the one defined in the exynos_tmu_data.c
for Exynos4 have been included.
This thermal-zones attribute is afterwards reused for Exynos4210,
Exynos4412 and Exynos5250.
Signed-off-by: Lukasz Majewski <l.majewski@samsung.com>
Acked-by: Eduardo Valentin <edubezval@gmail.com>
Signed-off-by: Kukjin Kim <kgene@kernel.org>
|
|
This code groups in one place default settings of trip points.
It is used in SoCs with multiple instances of TMU sensor.
Separate device tree file prevents from multiple copying of the
same data.
Signed-off-by: Lukasz Majewski <l.majewski@samsung.com>
Acked-by: Eduardo Valentin <edubezval@gmail.com>
Signed-off-by: Kukjin Kim <kgene@kernel.org>
|
