| Age | Commit message (Collapse) | Author |
|---|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound
Pull sound fixes from Takashi Iwai:
"Hopefully the final pull request for 3.19: this ended up with a
slightly higher volume than wished, but I put them all as they are
either stable or 3.19 regression fixes.
Most of commits are from ASoC, and have been stewed for a while in
linux-next. The only change in the common code is the regression
fixes for ASoC AC97 stuff wrt device registrations. The rest are
device-specific, mostly small fixes in various ASoC drivers and ak411x
on ice1724 boards"
* tag 'sound-3.19' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound:
ASoC: Intel: fix sst firmware path for cht-bsw-rt5672
ARM: dts: Fix I2S1, I2S2 compatible for exynos4 SoCs
ASoC: sgtl5000: add delay before first I2C access
MAINTAINERS: ASoC: add maintainer for Intel BDW/HSW ASoC driver
ASoC: atmel_ssc_dai: fix the setting for DSP mode
ASoC: sgtl5000: Use shift mask when setting codec mode
ASoC: tlv320aic3x: Fix data delay configuration
ALSA: ak411x: Fix stall in work callback
ASoC: Intel: Used lock version to update shim registers
ASoC: wm8731: init mutex in i2c init path
ASoC: atmel_ssc_dai: fix start event for I2S mode
ASoC: rt5640: Add RT5642 ACPI ID for Intel Baytrail
ASoC: wm97xx: Reset AC'97 device before registering it
ASoC: Add support for allocating AC'97 device before registering it
|
|
|
|
I2S1, I2S2 on Exynos4 SoC series have limited functionality compared
to I2S0, "samsung,s3c6410-i2s" compatible should be used for them.
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Cc: stable@vger.kernel.org
|
|
Pull ARM fixes from Russell King:
"A number of ARM fixes, the biggest is fixing a regression caused by
appended DT blobs exceeding 64K, causing the decompressor fixup code
to fail to patch the DT blob. Another important fix is for the ASID
allocator from Will Deacon which prevents some rare crashes seen on
some systems. Lastly, there's a build fix for v7M systems when printk
support is disabled.
The last two remaining fixes are more cosmetic - the IOMMU one
prevents an annoying harmless warning message, and we disable the
kernel strict memory permissions on non-MMU which can't support it
anyway"
* 'fixes' of git://ftp.arm.linux.org.uk/~rmk/linux-arm:
ARM: 8299/1: mm: ensure local active ASID is marked as allocated on rollover
ARM: 8298/1: ARM_KERNMEM_PERMS only works with MMU enabled
ARM: 8295/1: fix v7M build for !CONFIG_PRINTK
ARM: 8294/1: ATAG_DTB_COMPAT: remove the DT workspace's hardcoded 64KB size
ARM: 8288/1: dma-mapping: don't detach devices without an IOMMU during teardown
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM SoC fixes from Olof Johansson:
"One more week's worth of fixes. Worth pointing out here are:
- A patch fixing detaching of iommu registrations when a device is
removed -- earlier the ops pointer wasn't managed properly
- Another set of Renesas boards get the same GIC setup fixup as
others have in previous -rcs
- Serial port aliases fixups for sunxi. We did the same to tegra but
we caught that in time before the merge window due to more machines
being affected. Here it took longer for anyone to notice.
- A couple more DT tweaks on sunxi
- A follow-up patch for the mvebu coherency disabling in last -rc
batch"
* tag 'armsoc-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc:
arm: dma-mapping: Set DMA IOMMU ops in arm_iommu_attach_device()
ARM: shmobile: r8a7790: Instantiate GIC from C board code in legacy builds
ARM: shmobile: r8a73a4: Instantiate GIC from C board code in legacy builds
ARM: mvebu: don't set the PL310 in I/O coherency mode when I/O coherency is disabled
ARM: sunxi: dt: Fix aliases
ARM: dts: sun4i: Add simplefb node with de_fe0-de_be0-lcd0-hdmi pipeline
ARM: dts: sun6i: ippo-q8h-v5: Fix serial0 alias
ARM: dts: sunxi: Fix usb-phy support for sun4i/sun5i
|
|
There is currently a hardcoded limit of 64KB for the DTB to live in and
be extended with ATAG info. Some DTBs have outgrown that limit:
$ du -b arch/arm/boot/dts/omap3-n900.dtb
70212 arch/arm/boot/dts/omap3-n900.dtb
Furthermore, the actual size passed to atags_to_fdt() included the stack
size which is obviously wrong.
The initial DTB size is known, so use it to size the allocated workspace
with a 50% growth assumption and relocate the temporary stack above that.
This is also clamped to 32KB min / 1MB max for robustness against bad
DTB data.
Reported-by: Pali Rohár <pali.rohar@gmail.com>
Tested-by: Pavel Machek <pavel@ucw.cz>
Signed-off-by: Nicolas Pitre <nico@linaro.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
|
|
Pull networking fixes from David Miller:
1) Don't OOPS on socket AIO, from Christoph Hellwig.
2) Scheduled scans should be aborted upon RFKILL, from Emmanuel
Grumbach.
3) Fix sleep in atomic context in kvaser_usb, from Ahmed S Darwish.
4) Fix RCU locking across copy_to_user() in bpf code, from Alexei
Starovoitov.
5) Lots of crash, memory leak, short TX packet et al bug fixes in
sh_eth from Ben Hutchings.
6) Fix memory corruption in SCTP wrt. INIT collitions, from Daniel
Borkmann.
7) Fix return value logic for poll handlers in netxen, enic, and bnx2x.
From Eric Dumazet and Govindarajulu Varadarajan.
8) Header length calculation fix in mac80211 from Fred Chou.
9) mv643xx_eth doesn't handle highmem correctly in non-TSO code paths.
From Ezequiel Garcia.
10) udp_diag has bogus logic in it's hash chain skipping, copy same fix
tcp diag used. From Herbert Xu.
11) amd-xgbe programs wrong rx flow control register, from Thomas
Lendacky.
12) Fix race leading to use after free in ping receive path, from Subash
Abhinov Kasiviswanathan.
13) Cache redirect routes otherwise we can get a heavy backlog of rcu
jobs liberating DST_NOCACHE entries. From Hannes Frederic Sowa.
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net: (48 commits)
net: don't OOPS on socket aio
stmmac: prevent probe drivers to crash kernel
bnx2x: fix napi poll return value for repoll
ipv6: replacing a rt6_info needs to purge possible propagated rt6_infos too
sh_eth: Fix DMA-API usage for RX buffers
sh_eth: Check for DMA mapping errors on transmit
sh_eth: Ensure DMA engines are stopped before freeing buffers
sh_eth: Remove RX overflow log messages
ping: Fix race in free in receive path
udp_diag: Fix socket skipping within chain
can: kvaser_usb: Fix state handling upon BUS_ERROR events
can: kvaser_usb: Retry the first bulk transfer on -ETIMEDOUT
can: kvaser_usb: Send correct context to URB completion
can: kvaser_usb: Do not sleep in atomic context
ipv4: try to cache dst_entries which would cause a redirect
samples: bpf: relax test_maps check
bpf: rcu lock must not be held when calling copy_to_user()
net: sctp: fix slab corruption from use after free on INIT collisions
net: mv643xx_eth: Fix highmem support in non-TSO egress path
sh_eth: Fix serialisation of interrupt disable with interrupt & NAPI handlers
...
|
|
https://git.kernel.org/pub/scm/linux/kernel/git/mripard/linux into fixes
Merge "Allwinner fixes for 3.19" from Maxime Ripard:
Allwinner fixes for 3.19
A few minor fixes for the 3.19 kernel:
- The 8250 uart driver now respects the aliases, which pointed out that we
were using them wrong. Fixed them.
- The simplefb pipeline that was used on the A10 caused flickering and
tearing, and rendered it pretty much useless. Added a new simplefb node
with another pipeline that removes this issue. Note that we need to keep
the old node because u-boot 2015.01 uses it.
- Added a fix for the USB phy node on sun4i/sun5i
* tag 'sunxi-fixes-for-3.19' of https://git.kernel.org/pub/scm/linux/kernel/git/mripard/linux:
ARM: sunxi: dt: Fix aliases
ARM: dts: sun4i: Add simplefb node with de_fe0-de_be0-lcd0-hdmi pipeline
ARM: dts: sun6i: ippo-q8h-v5: Fix serial0 alias
ARM: dts: sunxi: Fix usb-phy support for sun4i/sun5i
Signed-off-by: Olof Johansson <olof@lixom.net>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM SoC fixes from Olof Johansson:
"A week's worth of fixes for various ARM platforms. Diff wise, the
largest fix is for OMAP to deal with how GIC now registers interrupts
(irq_domain_add_legacy() -> irq_domain_add_linear() changes).
Besides this, a few more renesas platforms needed the GIC instatiation
done for legacy boards. There's also a fix that disables coherency of
mvebu due to issues, and a few other smaller fixes"
* tag 'armsoc-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc:
arm64: dts: add baud rate to Juno stdout-path
ARM: dts: imx25: Fix PWM "per" clocks
bus: mvebu-mbus: fix support of MBus window 13
Merge tag 'mvebu-fixes-3.19-3' of git://git.infradead.org/linux-mvebu into fixes
ARM: mvebu: completely disable hardware I/O coherency
ARM: OMAP: Work around hardcoded interrupts
ARM: shmobile: r8a7779: Instantiate GIC from C board code in legacy builds
ARM: shmobile: r8a7778: Instantiate GIC from C board code in legacy builds
arm: boot: dts: dra7: enable dwc3 suspend PHY quirk
|
|
Commit f77d55a3b56a ("serial: 8250_dw: get index of serial line from DT
aliases") made the serial driver now use the serial aliases to get the tty
number, pointing out that our aliases have been wrong all along.
Remove them from the DTSI and add custom ones in the relevant boards.
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
|
|
The commit (3d125f9c91c5) cause i.MX6SX sdb enet cannot work. The cause is
the commit add mdio node with un-correct phy address.
The patch just correct i.MX6sx sdb board enet phy address.
V2:
* As Shawn's suggestion that unit-address should match 'reg' property, so
update ethernet-phy unit-address.
Acked-by: Stefan Agner <stefan@agner.ch>
Signed-off-by: Fugang Duan <B38611@freescale.com>
Acked-by: Shawn Guo <shawn.guo@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/glikely/linux
Pull devicetree bug fixes and documentation updates from Grant Likely:
"A few bugfixes for the new DT overlay feature, documentation updates,
spelling corrections, and changes to MAINTAINERS. Nothing earth
shattering here"
* tag 'devicetree-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/glikely/linux:
of/unittest: Overlays with sub-devices tests
of/platform: Handle of_populate drivers in notifier
of/overlay: Do not generate duplicate nodes
devicetree: document the "qemu" and "virtio" vendor prefixes
devicetree: document ARM bindings for QEMU's Firmware Config interface
Documentation: of: fix typo in graph bindings
dma-mapping: fix debug print to display correct dma_pfn_offset
of: replace Asahi Kasei Corp vendor prefix
ARM: dt: GIC: Spelling s/specific/specifier/, s/flaggs/flags/
dt/bindings: arm-boards: Spelling s/pointong/pointing/
MAINTAINERS: Update DT website and git repository
MAINTAINERS: drop DT regex matching on of_get_property and of_match_table
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/shawnguo/linux into fixes
Merge "ARM: imx: fixes for 3.19, 2nd round" from Shawn Guo:
The i.MX fixes for 3.19, 2nd round:
- Correct pwm clock assignment in i.MX25 device tree to fix the broken
pwm support on i.MX25
* tag 'imx-fixes-3.19-2' of git://git.kernel.org/pub/scm/linux/kernel/git/shawnguo/linux:
ARM: dts: imx25: Fix PWM "per" clocks
Signed-off-by: Olof Johansson <olof@lixom.net>
|
|
Testing has shown that on sun4i the display backend engine does not have
deep enough fifo-s causing flickering / tearing in full-hd mode due to
fifo underruns. This can be avoided by letting the display frontend engine
do the dma from memory, and then letting it feed the data directly into
the backend unmodified, as the frontend does have deep enough fifo-s.
Note since u-boot-v2015.01 has been released using the de_be0-lcd0-hdmi
pipeline on sun4i, we need to keep that one around too (unfortunately).
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
|
|
Currently PWM functionality is broken on mx25 due to the wrong assignment of the
PWM "per" clock.
According to Documentation/devicetree/bindings/clock/imx25-clock.txt:
pwm_ipg_per 52
,so update the pwm "per" to use 'pwm_ipg_per' instead of 'per10' clock.
With this change PWM can work fine on mx25.
Cc: <stable@vger.kernel.org>
Reported-by: Carlos Soto <csotoalonso@gmail.com>
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap into fixes
Merge "Urgent omap4 legacy interrupt regression fix for v3.19-rc series" from
Tony Lindgren:
A rather urgent pull request to fix omap4 legacy interrupts.
The legacy interrupts on omap4 got broken when gic got changed to
use irq_domain_add_linear() instead of the irq_domain_add_legacy(). We
still have the hardcoded legacy IRQ numbers in use in several places,
most notably the in the legacy DMA. It took a while to figure out
what the problem was and how it should be fixed for the -rc series.
Also include is a regression fix for the dra7 dwc3 suspend.
* tag 'omap-for-v3.19/gic-regression-v2' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap:
ARM: OMAP: Work around hardcoded interrupts
arm: boot: dts: dra7: enable dwc3 suspend PHY quirk
Signed-off-by: Olof Johansson <olof@lixom.net>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM SoC fixes from Olof Johansson:
"We've been sitting on our fixes branch for a while, so this batch is
unfortunately on the large side.
A lot of these are tweaks and fixes to device trees, fixing various
bugs around clocks, reg ranges, etc. There's also a few defconfig
updates (which are on the late side, no more of those).
All in all the diffstat is bigger than ideal at this time, but nothing
in here seems particularly risky"
* tag 'armsoc-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (31 commits)
reset: sunxi: fix spinlock initialization
ARM: dts: disable CCI on exynos5420 based arndale-octa
drivers: bus: check cci device tree node status
ARM: rockchip: disable jtag/sdmmc autoswitching on rk3288
ARM: nomadik: fix up leftover device tree pins
ARM: at91: board-dt-sama5: add phy_fixup to override NAND_Tree
ARM: at91/dt: sam9263: Add missing clocks to lcdc node
ARM: at91: sama5d3: dt: correct the sound route
ARM: at91/dt: sama5d4: fix the timer reg length
ARM: exynos_defconfig: Enable LM90 driver
ARM: exynos_defconfig: Enable options for display panel support
arm: dts: Use pmu_system_controller phandle for dp phy
ARM: shmobile: sh73a0 legacy: Set .control_parent for all irqpin instances
ARM: dts: berlin: correct BG2Q's SM GPIO location.
ARM: dts: berlin: add broken-cd and set bus width for eMMC in Marvell DMP DT
ARM: dts: berlin: fix io clk and add missing core clk for BG2Q sdhci2 host
ARM: dts: Revert disabling of smc91x for n900
ARM: dts: imx51-babbage: Fix ULPI PHY reset modelling
ARM: dts: dra7-evm: fix qspi device tree partition size
ARM: omap2plus_defconfig: use CONFIG_CPUFREQ_DT
...
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/kgene/linux-samsung into fixes
Merge "Samsung fixes for v3.19" from Kukjin Kim:
Samsung fixes for v3.19
- exynos_defconfig: enable LM90 driver and display panel support
- HWMON
- SENSORS_LM90
- Direct Rendering Manager (DRM)
- DRM bridge registration and lookup framework
- Parade ps8622/ps8625 eDP/LVDS bridge
- NXP ptn3460 eDP/LVDS bridge
- Exynos Fully Interactive Mobile Display controller (FIMD)
- Panel registration and lookup framework
- Simple panels
- Backlight & LCD device support
- use pmu_system_controller phandle for dp phy
: DP PHY requires pmu_system_controller to handle PMU reg. now
* tag 'samsung-fixes-3.19' of git://git.kernel.org/pub/scm/linux/kernel/git/kgene/linux-samsung:
ARM: exynos_defconfig: Enable LM90 driver
ARM: exynos_defconfig: Enable options for display panel support
arm: dts: Use pmu_system_controller phandle for dp phy
Signed-off-by: Olof Johansson <olof@lixom.net>
|
|
The arndale-octa board was giving "imprecise external aborts" during
boot-up with MCPM enabled. CCI enablement of the boot cluster was found
to be the cause of these aborts (possibly because the secure f/w was not
allowing it). Hence, disable CCI for the arndale-octa board.
Signed-off-by: Abhilash Kesavan <a.kesavan@samsung.com>
Tested-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Tested-by: Kevin Hilman <khilman@linaro.org>
Tested-by: Tyler Baker <tyler.baker@linaro.org>
Signed-off-by: Olof Johansson <olof@lixom.net>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/nferre/linux-at91 into fixes
Merge "at91: fixes for 3.19 #1 (ter)" from Nicolas Ferre:
First fixes batch for AT91 on 3.19:
- fix some DT entries
- correct clock entry for the at91sam9263 LCD
- add a phy_fixup for Eth1 on sama5d4
* tag 'at91-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/nferre/linux-at91:
ARM: at91: board-dt-sama5: add phy_fixup to override NAND_Tree
ARM: at91/dt: sam9263: Add missing clocks to lcdc node
ARM: at91: sama5d3: dt: correct the sound route
ARM: at91/dt: sama5d4: fix the timer reg length
Signed-off-by: Olof Johansson <olof@lixom.net>
|
|
git://git.infradead.org/users/hesselba/linux-berlin into fixes
Merge "ARM: berlin: Fixes for v3.19 (round 1)" from Sebastian Hesselbarth:
Marvell Berlin fixes for v3.19 round 1:
- SDHCI DT fixes for BG2Q and BG2Q reference board
- BG2Q SM GPIO DT node relocation
* tag 'berlin-fixes-for-3.19-1' of git://git.infradead.org/users/hesselba/linux-berlin:
ARM: dts: berlin: correct BG2Q's SM GPIO location.
ARM: dts: berlin: add broken-cd and set bus width for eMMC in Marvell DMP DT
ARM: dts: berlin: fix io clk and add missing core clk for BG2Q sdhci2 host
Signed-off-by: Olof Johansson <olof@lixom.net>
|
|
We altered the device tree bindings for the Nomadik family of
pin controllers to be standard, this file was merged out-of-order
so we missed fixing this. Fix it up.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Olof Johansson <olof@lixom.net>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap into fixes
Merge "omap fixes against v3.19-rc1" from Tony Lindgren:
Fixes for omaps mostly to deal with dra7 timer issues
and hypervisor mode. The other fixes are minor fixes for
various boards. The summary of the fixes is:
- Fix real-time counter rate typos for some frequencies
- Fix counter frequency drift for am572x
- Fix booting of secondary CPU in HYP mode
- Fix n900 board name for legacy user space
- Fix cpufreq in omap2plus_defconfig after Kconfig change
- Fix dra7 qspi partitions
And also, let's re-enable smc91x on some n900 boards that
we have sitting in a few test boot systems after the boot
loader dependencies got fixed.
* tag 'omap-for-v3.19/fixes-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap:
ARM: dts: Revert disabling of smc91x for n900
ARM: dts: dra7-evm: fix qspi device tree partition size
ARM: omap2plus_defconfig: use CONFIG_CPUFREQ_DT
ARM: OMAP2+: Fix n900 board name for legacy user space
ARM: omap5/dra7xx: Enable booting secondary CPU in HYP mode
ARM: dra7xx: Fix counter frequency drift for AM572x errata i856
ARM: omap5/dra7xx: Fix frequency typos
Signed-off-by: Olof Johansson <olof@lixom.net>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/shawnguo/linux into fixes
Merge "ARM: imx: fixes for 3.19" from Shawn Guo:
The i.MX fixes for 3.19:
- One fix for incorrect i.MX25 SPI1 clock assignment in device tree,
which causes system hang when accessing SPI1.
- Correct i.MX6SX QSPI parent clock configuration to fix a kernel Oops.
- Fix ULPI PHY reset modelling on imx51-babbage board to remove the
dependency on bootloader for USB3317 ULPI PHY reset.
- Correct video divider setting on i.MX6Q rev T0 1.0 to fix the issue
that HDMI is not working at high resolution on T0 1.0.
- One incremental fix for CODA960 VPU enabling in device tree to
correct interrupt order.
- LS1021A SCFG block works in BE mode, add device tree property
big-endian to make it right.
* tag 'imx-fixes-3.19' of git://git.kernel.org/pub/scm/linux/kernel/git/shawnguo/linux:
ARM: dts: imx51-babbage: Fix ULPI PHY reset modelling
ARM: imx6sx: Set PLL2 as parent of QSPI clocks
ARM: dts: imx25: Fix the SPI1 clocks
ARM: clk-imx6q: fix video divider for rev T0 1.0
ARM: dts: imx6qdl: Fix CODA960 interrupt order
ARM: ls1021a: dtsi: add 'big-endian' property for scfg node
Signed-off-by: Olof Johansson <olof@lixom.net>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/mmind/linux-rockchip into fixes
Merge "ARM: rockchip: dts fix for 3.19" from Heiko Stübner:
Increase drive-strength to sdmmc pins on rk3288-evb to fix
an issue with the fixed highspeed card detection.
* tag 'v3.19-rockchip-dtsfixes1' of git://git.kernel.org/pub/scm/linux/kernel/git/mmind/linux-rockchip:
ARM: dts: rockchip: bump sd card pin drive strength up on rk3288-evb
Signed-off-by: Olof Johansson <olof@lixom.net>
|
|
Whenever Suspend PHY bit is set on DRA7x devices,
USB will not work due to Set EP Configuration command
always failing.
This was only found after a recent commit 2164a47 (usb:
dwc3: set SUSPHY bit for all cores, which will be merged
for v3.19) added a missing *required* step to dwc3
initialization. Synopsys Databook requires that we enable
Suspend PHY bit after initialization but that, unfortunately,
breaks DRA7x.
Note that the same regression was already patched for AM437x.
Reported-by: Roger Quadros <rogerq@ti.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
|
On i.MX28, the MDIO bus is shared between the two FEC instances.
The driver makes sure that the second FEC uses the MDIO bus of the
first FEC. This is done conditionally if FEC_QUIRK_ENET_MAC is set.
However, in newer designs, such as Vybrid or i.MX6SX, each FEC MAC
has its own MDIO bus. Simply removing the quirk FEC_QUIRK_ENET_MAC
is not an option since other logic, triggered by this quirk, is
still needed.
Furthermore, there are board designs which use the same MDIO bus
for both PHY's even though the second bus would be available on the
SoC side. Such layout are popular since it saves pins on SoC side.
Due to the above quirk, those boards currently do work fine. The
boards in the mainline tree with such a layout are:
- Freescale Vybrid Tower with TWR-SER2 (vf610-twr.dts)
- Freescale i.MX6 SoloX SDB Board (imx6sx-sdb.dts)
This patch adds a new quirk FEC_QUIRK_SINGLE_MDIO for i.MX28, which
makes sure that the MDIO bus of the first FEC is used in any case.
However, the boards above do have a SoC with a MDIO bus for each FEC
instance. But the PHY's are not connected in a 1:1 configuration. A
proper device tree description is needed to allow the driver to
figure out where to find its PHY. This patch fixes that shortcoming
by adding a MDIO bus child node to the first FEC instance, along
with the two PHY's on that bus, and making use of the phy-handle
property to add a reference to the PHY's.
Acked-by: Sascha Hauer <s.hauer@pengutronix.de>
Signed-off-by: Stefan Agner <stefan@agner.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Current vendor-prefixes.txt already has "ak" prefix for Asahi Kasei Corp
by ae8c4209af2c(of: Add vendor prefix for Asahi Kasei Corp.)
It went through the appropriate review process. But, almost all
Asahi Kasei chip drivers are using "asahi-kasei" prefix today.
(arch/arm/boot/dts/tegra20-seaboard.dts only is using "ak,ak8975",
but there are instances of "asahi-kasei,ak8975" in other dts files.
And drivers/iio/magnetometer/ak8975.c doesn't support "ak,ak8975" prefix)
So, we made a mistake there.
In addition, checkpatch.pl reports WARNING if it is using "asahi-kasei"
prerfix in DT file.
(DT compatible string vendor "asahi-kasei" appears un-documented)
Marking it deprecated and warning with checkpatch is certainly
preferable. So, this patch replace "ak" to "asahi-kasei" in
vendor-prefixes.txt. (and fixup tegra20-seaboard)
OTOH, Asahi Kasei is usually referred to as "AKM", but this patch
doesn't care about it. Because no DT is using that today.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Acked-by: Thierry Reding <treding@nvidia.com>
Acked-by: Alexandre Courbot <acourbot@nvidia.com>
Signed-off-by: Rob Herring <robh@kernel.org>
|
|
atmel_lcdfb needs also uses hclk clock, but AT91SAM9263 doesn't have that
specific clock, so use lcd_clk twice. The same was done in
arch/arm/mach-at91/at91sam9263.c
Signed-off-by: Alexander Stein <alexanders83@web.de>
Acked-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
|
|
The MICBIAS is a supply, should route to MIC while not IN1L.
Signed-off-by: Bo Shen <voice.shen@atmel.com>
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
|
|
The second property of reg is the length, so correct it for timer.
Signed-off-by: Bo Shen <voice.shen@atmel.com>
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
|
|
DP PHY now require pmu-system-controller to handle PMU register
to control PHY's power isolation. Adding the same to dp-phy
node.
Signed-off-by: Vivek Gautam <gautam.vivek@samsung.com>
Reviewed-by: Jingoo Han <jg1.han@samsung.com>
Tested-by: Javier Martinez Canillas <javier.martinez@collabora.co.uk>
Signed-off-by: Kukjin Kim <kgene@kernel.org>
|
|
The gpio4 and gpio5 are in 0xf7fc0000 apb which is located in the SM domain.
This patch moves gpio4 and gpio5 to the correct location. This patch also
renames them as the following to match the names we internally used in
marvell:
gpio4 -> sm_gpio1
gpio5 -> sm_gpio0
porte -> portf
portf -> porte
This also matches what we did for BG2 and BG2CD's SM GPIO.
Cc: stable@vger.kernel.org # 3.16+
Fixes: cedf57fc4f2f ("ARM: dts: berlin: add the BG2Q GPIO nodes")
Signed-off-by: Jisheng Zhang <jszhang@marvell.com>
Signed-off-by: Sebastian Hesselbarth <sebastian.hesselbarth@gmail.com>
|
|
There's no card detection for the eMMC, so this patch adds the missing
broken-cd property. This patch also sets bus width as 8 to add
MMC_CAP_8_BIT_DATA in the Host capabilities.
Cc: stable@vger.kernel.org # 3.16+
Fixes: 3047086dfd56 ("ARM: dts: berlin: enable SD card reader and eMMC for the BG2Q DMP")
Signed-off-by: Jisheng Zhang <jszhang@marvell.com>
Signed-off-by: Sebastian Hesselbarth <sebastian.hesselbarth@gmail.com>
|
|
On BG2Q, the sdhci2 host uses nfcecc for "io" clk and nfc for "core" clk.
The shdci2 can't work without this patch due to the "core" clk is gated.
Cc: stable@vger.kernel.org # 3.16+
Fixes: 0d859a6a9d14 ("ARM: dts: berlin: add the SDHCI nodes for the BG2Q")
Signed-off-by: Jisheng Zhang <jszhang@marvell.com>
Signed-off-by: Sebastian Hesselbarth <sebastian.hesselbarth@gmail.com>
|
|
Revert "ARM: dts: Disable smc91x on n900 until bootloader
dependency is removed". We've now fixed the issues that
caused problems with uninitialized hardware depending on
the bootloader version. Mostly things got fixed with
the following commits:
9a894953a97b ("ARM: dts: Fix bootloader version dependencies by muxing n900 smc91x pins")
7d2911c43815 ("net: smc91x: Fix gpios for device tree based booting")
Note that this only affects the early development boards
with Ethernet that we still have in a few automated boot
test systems. And it's also available supposedly in some
versions of qemu.
Tested-by: Kevin Hilman <khilman@linaro.org>
Tested-by: Aaro Koskinen <aaro.koskinen@iki.fi>
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
|
GPIO2_5 is the reset GPIO for the USB3317 ULPI PHY. Instead of modelling it as
a regulator, the correct approach is to use the 'reset_gpios' property of the
"usb-nop-xceiv" node.
GPIO1_7 is the reset GPIO for the USB2517 USB hub. As we currently don't have
dt bindings to describe a HUB reset, let's keep using the regulator approach.
Rename the regulator to 'reg_hub_reset' to better describe its function and bind
it with the USB host1 port instead.
USB host support has been introduced by commit 9bf206a9d13be3 ("ARM: dts:
imx51-babbage: Add USB Host1 support"), which landed in 3.16 and it seems that
USB has only been functional due to previous bootloader initialization.
With this patch applied we can get USB host to work without relying on the
bootloader.
Cc: <stable@vger.kernel.org> # 3.16+
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
|
|
The Ippo q8h has its serial console connected to the r-uart. Adjust the
serial0 alias to match.
This fixes the kernel serial console no longer working since 3.19-rc1, because
8250_dw.c now honors dt aliases, causing the serial console to be ttyS5 rather
then being ttyS0, as it was in 3.18 and before.
Note that adjusting bootargs instead is not an acceptable fix, because
console=ttyS0,115200 is used by a lot of bootscripts, etc. and this should
continue to work.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
|
|
64KiB is allocated for qspi dtb partition which is not
sufficient, so updating the partition table size to 512KiB
for device tree partition.
This also aligns the QSPI partition definitions between
kernel and U-Boot.
Fixes: dc2dd5b8 ("ARM: dts: dra7: Add qspi device")
Signed-off-by: Mugunthan V N <mugunthanvnm@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
|
From Documentation/devicetree/bindings/clock/imx25-clock.txt:
cspi1_ipg 78
cspi2_ipg 79
cspi3_ipg 80
, so fix the SPI1 clocks accordingly to avoid a kernel hang when trying to
access SPI1.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
|
|
Commit a04a0b6fed4f ("ARM: dts: imx6qdl: Enable CODA960 VPU") lost the
fix for the CODA960 interrupt order during a rebase before being applied.
This patch adds the missing bit and brings the interrupts and
interrupt-names properties back in sync.
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
Reviewed-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
|
|
On LS1021A SoC, the scfg device is in BE mode.
Signed-off-by: Xiubo Li <Li.Xiubo@freescale.com>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
|
|
usbphy0 support in the sunxi usb-phy driver has been merged, but the
dtsi's for sun4i/sun5i haven't been updated. This results in the phy
driver failing to load, breaking usb support.
Fixes: 6827a46f5994 ('phy: sun4i: add support for USB phy0')
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
|
|
It seems that ever since (536f6b9 mmc: dw_mmc: Reset DMA before
enabling IDMAC) landed upstream that SD cards have been very unhappy
on rk3288-evb. They were a little unhappy before that change, but
after that change they're REALLY unhappy.
It turns out that the above fix happens to fix a corruption when
reading card information during probe time. Without the fix we didn't
detect that high speed SD cards could actually support high speed.
With the fix we suddenly detect that they're high speed and we try to
use them at 50MHz. That doesn't work so well on EVB with the default
drive strength (maybe because there are two physical SD card slots
hooked up to the same pin?).
Fix the problem by bumping up the drive strength of the sdmmc lines.
Signed-off-by: Doug Anderson <dianders@chromium.org>
Fixes: 536f6b91d21b ("mmc: dw_mmc: Reset DMA before enabling IDMAC")
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
|
|
The commit b4607572ef86 (ARM: mvebu: remove conflicting muxing on
Armada 370 DB) removes the hog pins muxing. As it is explained in the
commit log it solves a warning a boot time, but more important it also
allows using the Giga port 0 of the board.
Unfortunately in the same time the commit 4904a82a9399 (arm: mvebu:
move Armada 370/XP pinctrl node definition armada-370-xp.dtsi) was
merged and it introduced again the hog pins muxing. Because of it, the
Giga port 0 of the board is no more usable.
This commit remove again the conflicting muxing (hopefully for the
last time).
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
[andrew@lunn.ch: Correct commit IDs]
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Fixes: 4904a82a9399 ("arm: mvebu: move Armada 370/XP pinctrl node definition armada-370-xp.dtsi")
|
|
git://git.linaro.org/people/mike.turquette/linux
Pull clk framework updates from Mike Turquette:
"This is much later than usual due to several last minute bugs that had
to be addressed. As usual the majority of changes are new drivers and
modifications to existing drivers. The core recieved many fixes along
with the groundwork for several large changes coming in the future
which will better parition clock providers from clock consumers"
* tag 'clk-for-linus-3.19' of git://git.linaro.org/people/mike.turquette/linux: (86 commits)
clk: samsung: Fix Exynos 5420 pinctrl setup and clock disable failure due to domain being gated
ARM: OMAP3: clock: fix boot breakage in legacy mode
ARM: OMAP2+: clock: fix DPLL code to use new determine rate APIs
clk: Really fix deadlock with mmap_sem
clk: mmp: fix sparse non static symbol warning
clk: Change clk_ops->determine_rate to return a clk_hw as the best parent
clk: change clk_debugfs_add_file to take a struct clk_hw
clk: Don't expose __clk_get_accuracy
clk: Don't try to use a struct clk* after it could have been freed
clk: Remove unused function __clk_get_prepare_count
clk: samsung: Fix double add of syscore ops after driver rebind
clk: samsung: exynos4: set parent of sclk_hdmiphy to hdmi
clk: samsung: exynos4415: Fix build with PM_SLEEP disabled
clk: samsung: remove unnecessary inclusion of header files from clk.h
clk: samsung: remove unnecessary CONFIG_OF from clk.c
clk: samsung: Spelling s/bwtween/between/
clk: rockchip: Add support for the mmc clock phases using the framework
clk: rockchip: add bindings for the mmc clocks
clk: rockchip: rk3288 export i2s0_clkout for use in DT
clk: rockchip: use clock ID for DMC (memory controller) on rk3288
...
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/rzhang/linux
Pull thermal management update from Zhang Rui:
"Summary:
- of-thermal extension to allow drivers to register and use its
functionality in a better way, without exploiting thermal core.
From Lukasz Majewski.
- Fix a bug in intel_soc_dts_thermal driver which calls a sleep
function in interrupt handler. From Maurice Petallo.
- add a thermal UAPI header file for exporting the thermal generic
netlink information to user-space. From Florian Fainelli.
- First round of refactoring in Exynos driver. Bartlomiej and Lukasz
are attempting to make it lean and easier to understand.
- New thermal driver for Rockchip (rk3288), with support for DT
thermal. From Caesar Wang.
- New thermal driver for Nvidia, Tegra124 SOCTHERM driver, with
support for DT thermal. From Mikko Perttunen.
- New cooling device, based on common clock framework. From Eduardo
Valentin.
- a couple of small fixes in thermal core framework. From Srinivas
Pandruvada, Javi Merino, Luis Henriques.
- Dropping Armada A375-Z1 SoC thermal support as the chip is not in
the market, armada folks decided to drop its support.
- a couple of small fixes and cleanups in int340x thermal driver"
* 'next' of git://git.kernel.org/pub/scm/linux/kernel/git/rzhang/linux: (58 commits)
thermal: provide an UAPI header file
Thermal/int340x: Clear the error value of the last acpi_bus_get_device() call
thermal/powerclamp: add id for braswell cpu
thermal: Intel SoC DTS: Don't do thermal zone update inside spin_lock
Thermal: fix platform_no_drv_owner.cocci warnings
Thermal/int340x: avoid unnecessary pointer casting
thermal: int3403: Delete a check before thermal_zone_device_unregister()
thermal/int3400: export uuids
thermal: of: Extend current of-thermal.c code to allow setting emulated temp
thermal: of: Extend of-thermal to export table of trip points
thermal: of: Rename struct __thermal_trip to struct thermal_trip
thermal: of: Extend of-thermal.c to provide check if trip point is valid
thermal: of: Extend of-thermal.c to provide number of trip points
thermal: Fix error path in thermal_init()
thermal: lock the thermal zone when switching governors
thermal: core: ignore invalid trip temperature
thermal: armada: Remove support for A375-Z1 SoC
thermal: rockchip: add driver for thermal
dt-bindings: document Rockchip thermal
thermal: exynos: remove exynos_tmu_data.h include
...
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM SoC DT updates part 2 from Arnd Bergmann:
"This is a follow-up to the early ARM SoC DT changes, with additional
content that has external dependencies:
- The Tegra IOMMU DT support depends on changes from the iommu tree,
plus the contents of the arm-soc drivers branch
- The MVEBU PHY support depends on changes from the phy tree
- The AT91 DT support depends on changes from the RTC and DMA-slave
trees
All of these changes just enable additional devices for existing
platforms"
* tag 'dt2-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc:
ARM: tegra: Enable IOMMU for display controllers on Tegra124
ARM: tegra: Enable IOMMU for display controllers on Tegra114
ARM: tegra: Enable IOMMU for display controllers on Tegra30
ARM: tegra: Add memory controller support for Tegra124
ARM: tegra: Add memory controller support for Tegra114
ARM: tegra: Add memory controller support for Tegra30
ARM: tegra: Add APB_MISC_GP as a MIPI pad control bank
ARM: mvebu: add PHY support to the dts for the USB controllers on Armada 375
ARM: mvebu: add Device Tree description of USB cluster controller on Armada 375
ARM: at91/dt: at91sam9g45: add ISI node
ARM: at91/dt: enable the RTT block on the at91sam9m10g45ek board
ARM: at91/dt: enable the RTT block on the sam9g20ek board
ARM: at91/dt: add GPBR nodes
ARM: at91/dt: add RTT nodes to at91 dtsis
ARM: at91/dt: at91sam9rl: add rtc
ARM: at91: fix GPLv2 wording
ARM: at91/dt: sama5d4: add DMA support
ARM: at91/dt: sama5d4: use macro instead of numeric value
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM SoC fixes from Arnd Bergmann:
"Here are the first arm-soc bug fixes. Most of these are OMAP related
fixes for regressions or minor bugs. Aside from that, there are a few
defconfig changes for various platforms"
* tag 'fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc:
iommu/exynos: Fix arm64 allmodconfig build
ARM: defconfigs: use CONFIG_CPUFREQ_DT
ARM: omap2plus_defconfig: Enable AHCI_PLATFORM driver
ARM: dts: am437x-sk-evm.dts: fix LCD timings
ARM: dts: dra7-evm: Update SMPS7 (VDD_CORE) max voltage to match DM
ARM: dts: dra7-evm: Fix typo in SMPS6 (VDD_GPU) max voltage
ARM: OMAP2+: AM43x: Add ID for ES1.2
ARM: dts: am437x-sk: fix lcd enable pin mux data
ARM: dts: Fix gpmc regression for omap 2430sdp smc91x
Revert "ARM: shmobile: multiplatform: add Audo DMAC peri peri support on defconfig"
ARM: dts: dra7: fix DSS PLL clock mux registers
ARM: dts: DRA7: wdt: Fix compatible property for watchdog node
ARM: OMAP2+: clock: remove unused function prototype
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/staging
Pull staging driver updates from Greg KH:
"Here's the big staging tree pull request for 3.19-rc1.
We continued to delete more lines than were added, always a good
thing, but not at a huge rate this release, only about 70k lines
removed overall mostly from removing the horrid bcm driver.
Lots of normal staging driver cleanups and fixes all over the place,
well over a thousand of them, the shortlog shows all the horrid
details.
The "contentious" thing here is the movement of the Android binder
code out of staging into the "real" part of the kernel. This is code
that has been stable for a few years now and is working as-is in the
tens of millions of devices with no issues. Yes, the code is horrid,
and the userspace api leaves a lot to be desired, but it's not going
to change due to legacy issues that we have no control over. Because
so many devices and companies rely on this, and the code is stable,
might as well promote it out of staging.
This was all discussed at the Linux Plumbers conference, and everyone
participating agreed that this was the best way forward.
There is work happening to replace the binder code with something new
that is happening right now, but I don't expect to see the results of
that work for another year at the earliest. If that ever happens, and
Android switches over to it, I'll gladly remove this version.
As for maintainers, I'll be glad to maintain this code, I've been
doing it for the past few years with no problems. I'll send a
MAINTAINERS entry for it before 3.19-final is out, still need to talk
to the Google developers about if they are willing to help with it or
not, last I checked they were, which was good.
All of these patches have been in linux-next for a while with no
reported issues"
* tag 'staging-3.19-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/staging: (1382 commits)
Staging: slicoss: Fix long line issues in slicoss.c
staging: rtl8712: remove unnecessary else after return
staging: comedi: change some printk calls to pr_err
staging: rtl8723au: hal: Removed the extra semicolon
lustre: Deletion of unnecessary checks before three function calls
staging: lustre: fix sparse warnings: static function declaration
staging: lustre: fixed sparse warnings related to static declarations
staging: unisys: remove duplicate header
staging: unisys: remove unneeded structure
staging: ft1000 : replace __attribute ((__packed__) with __packed
drivers: staging: rtl8192e: Include "asm/unaligned.h" instead of "access_ok.h" in "rtl819x_BAProc.c"
Drivers:staging:rtl8192e: Fixed checkpatch warning
Drivers:staging:clocking-wizard: Added a newline
staging: clocking-wizard: check for a valid clk_name pointer
staging: rtl8723au: Hal_InitPGData() avoid unnecessary typecasts
staging: rtl8723au: _DisableAnalog(): Avoid zero-init variables unnecessarily
staging: rtl8723au: Remove unnecessary wrapper _ResetDigitalProcedure1()
staging: rtl8723au: _ResetDigitalProcedure1_92C() reduce code obfuscation
staging: rtl8723au: Remove unnecessary wrapper _DisableRFAFEAndResetBB()
staging: rtl8723au: _DisableRFAFEAndResetBB8192C(): Reduce code obfuscation
...
|
