Age | Commit message (Collapse) | Author |
|
note: there are still intermittent detection errors with USB0
Signed-off-by: Russell Robinson Jr <rrobinson@phytec.com>
|
|
ehci changes are currently only used with phyCORE-Vybrid (pcm052)
Signed-off-by: Russell Robinson Jr <rrobinson@phytec.com>
|
|
Signed-off-by: Russell Robinson Jr <rrobinson@phytec.com>
|
|
Signed-off-by: Russell Robinson Jr <rrobinson@phytec.com>
|
|
Signed-off-by: Russell Robinson Jr <rrobinson@phytec.com>
|
|
From Singh Pradip-B09147. Integrate by Jason Jin
Signed-off-by: Jason Jin <Jason.jin@freescale.com>
|
|
Add platform support for ADC driver.
Signed-off-by: Wang Xiaojun <b41435@freescale.com>
|
|
Handle usb suspend/resume, currently the BSP doesn't
support usb plug/unplug wakeup.
Signed-off-by: Jingchang Lu <b35083@freescale.com>
|
|
Signed-off-by: Jingchang Lu <b35083@freescale.com>
|
|
System could run into STOP and LPRun modes. When system was working in STOP mode,
pressing SW1 button or inserting or removing SD card could wake up it.
Signed-off-by: Alison Wang <b18965@freescale.com>
|
|
Add platform support for Vybrid L2 switch driver.
Signed-off-by: Jason Jin <Jason.jin@freescale.com>
|
|
Add second FEC support for Vybrid.
Signed-off-by: Alison Wang <b18965@freescale.com>
|
|
Add platform support for watchdog driver.
Signed-off-by: Wang Xiaojun <b41435@freescale.com>
|
|
Add hardware flow control support,
Add transmit DMA support,
Add FIFO operation support,
Add MSB/LSB on data support,
Add 9-bits MARK/SPACE support.
Signed-off-by: Jingchang Lu <b35083@freescale.com>
|
|
Add platform support for Quad SPI driver.
Signed-off-by: Alison Wang <b18965@freescale.com>
Xiaochun Li <b41219@freescale.com>
|
|
Add platform support for touch screen driver.
Signed-off-by: Alison Wang <b18965@freescale.com>
|
|
Update platform support for dspi driver after debugging on board.
Signed-off-by: Jason Jin <jason.jin@freescale.com>
Alison Wang <b18965@freescale.com>
|
|
Four LEDS are connected to FTM0 ch0~3 on TWR-MVF600 board,
the PWM signal can use control these LEDS on/off or demo.
Signed-off-by: Jingchang Lu <b35083@freescale.com>
|
|
The FlexTimer work on PWM mode with EPWM and CPWM supported.
The API configures each FTM channels the same due to pwm subsystem
interface restriction.
Signed-off-by: Jingchang Lu <b35083@freescale.com>
|
|
Signed-off-by: Jingchang Lu <b35083@freescale.com>
|
|
This patch enable the ADMA2 function for the SDHC module used
on Faraday board. Please note that the ADMA address should be 16
bytes aligned other than 4 byte in the spec.
This patch also increased the SDHC module frequency to 200MHz.
Signed-off-by: Jason Jin <Jason.jin@freescale.com>
|
|
This patch increase the delay time for the pll clock to lock. otherwise
the kernel will panic for the locking failure.
Signed-off-by: Jason Jin <Jason.jin@freescale.com>
|
|
OTG1 acts as gadget and OTG2 acts as host on TWR-MVF600 board.
Signed-off-by: Jingchang Lu <b35083@freescale.com>
|
|
Add platform support for FEC driver.
Signed-off-by: Jason Jin <Jason.jin@freescale.com>
Signed-off-by: Alison Wang <b18965@freescale.com>
|
|
Add MSL support for MVF platform.
Signed-off-by: Jason Jin <Jason.jin@freescale.com>
Signed-off-by: Alison Wang <b18965@freescale.com>
Signed-off-by: Jingchang Lu <b35083@freescale.com>
|