Age | Commit message (Expand) | Author |
2013-10-22 | nit6xlite: set GPIO outputs low | Eric Nelson |
2013-10-21 | Allow OV5640 parallel | Eric Nelson |
2013-10-17 | nitrogen6x: enable ARM PMU | Philip Craig |
2013-10-08 | nit6xlite: request and set direction for BCM GPIOs, leave BT enabled | Eric Nelson |
2013-10-03 | Revert "ENGR00243339 imx: sata: disable sata phy when sata is not enabled" | Eric Nelson |
2013-09-12 | pads-mx6_utc.h: change usdhc3 pads to 47K pu, 80 Ohm drive strength, (normal ... | Troy Kisky |
2013-09-12 | pads-mx6_utc.h: remove pull-up on Atheros ethernet pads | Troy Kisky |
2013-09-09 | board-mx6_utc: initial addition | Troy Kisky |
2013-09-03 | s: implement poweroff by pulling GP2:7 low | Eric Nelson |
2013-09-03 | s: add NANDF_D7 (GP2:7) as GPIO power key | Eric Nelson |
2013-09-03 | nit6xlite: GPIO1 is usb_otg_id, GPIO3:22 is vbus enable | Troy Kisky |
2013-09-03 | disable SDMA on UARTs | Eric Nelson |
2013-09-03 | nit6xlite: Add PWM3 backlight (pwm.backlight.2) | Eric Nelson |
2013-09-03 | mx6qsaberlite: Add DVFS, MIPI_CSI2 and PERFMON | Robert Winkler |
2013-09-03 | nit6xlite: use SDIO set_power callback | Eric Nelson |
2013-09-03 | s: use platform-specific sdio set_power callback | Eric Nelson |
2013-09-03 | sdhci/sdhci-esdhc-imx: Allow platform-specific set_power callback | Eric Nelson |
2013-09-03 | board-mx6_s: export GPIOs, remove buttons | Eric Nelson |
2013-09-03 | board-mx6_s: add GPIOs | Eric Nelson |
2013-09-03 | board-mx6_s: cleanup | Eric Nelson |
2013-09-03 | board-mx6_s: add CSPI2 | Eric Nelson |
2013-09-03 | board-mx6_s: Add GPIO pins, CSPI2 | Eric Nelson |
2013-09-03 | board-mx6_s: clean up tsc2007 stuff | Eric Nelson |
2013-09-03 | s: cleanup: no MIPI or adV7x devices, camera and HDMI on I2C3 | Eric Nelson |
2013-09-03 | preliminary support for Boundary Devices S board | Eric Nelson |
2013-09-03 | nitrogen6x: add KSZ9031 support | Troy Kisky |
2013-09-03 | board-mx6_nitrogen6x: restore imx6q_add_v4l2_output | Troy Kisky |
2013-09-03 | h: wait for power button press/release in pm_power_off | Eric Nelson |
2013-09-03 | Fix adv7180 patch. | Eric Nelson |
2013-09-03 | SABRE Lite/variants: implicitly set SD2 pads | Eric Nelson |
2013-09-03 | mx6_h: add initial board file | Troy Kisky |
2013-09-03 | msi: fix INT D, when msi is in use(not quite working) | Troy Kisky |
2013-09-03 | mx6_nitrogen6x: add adv7180 tv input camera | Troy Kisky |
2013-09-03 | mx6_nitrogen6x: add static to mxc_iomux_v3_setup_pads | Troy Kisky |
2013-09-03 | mx6_nitrogen6x: rename _spi_flash_data to spi_flash_data | Troy Kisky |
2013-09-03 | board-mx6_oc: add static to mxc_iomux_v3_setup_pads | Troy Kisky |
2013-09-03 | Support adv739x TV encoder for BT656 output. | Qiang.li |
2013-09-03 | i.MX6: default to 1GHz on TO 1.0 | Eric Nelson |
2013-09-03 | nit6xlite: define dry-contact pin on GPIO1:6 (pad GPIO_6) | Eric Nelson |
2013-09-03 | nit6xlite/oc: release BT_RESET pin for userspace use | Eric Nelson |
2013-09-03 | nit6xlite+oc: amp_enable() routine is local to board file | Eric Nelson |
2013-09-03 | nitrogen6x: sys_timer is called early | Eric Nelson |
2013-09-03 | nitrogen6x: is_nitrogen6w() is called during init | Eric Nelson |
2013-09-03 | mach-mx6/pcie: remove __devinit, __initdata, __init references | Eric Nelson |
2013-09-03 | Add Boundary Devices i.MX6 Nitrogen6x Lite board. | Eric Nelson |
2013-09-03 | mx6_oc: initial addition of board files | Eric Nelson |
2013-09-03 | i.MX6: Add Nitrogen6X board and configs | Eric Nelson |
2013-09-03 | mx6: add CONFIG_PCIE_FORCE_GEN1 | Troy Kisky |
2013-09-03 | pcie: force gen1 speed | Troy Kisky |
2013-09-03 | mx6: add clock for imx-uart.4 | Troy Kisky |