| Age | Commit message (Collapse) | Author |
|---|
|
Everything should now be using sparsemem rather than discontigmem, so
remove the code supporting discontigmem from ARM.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
|
|
delay_detect in HZ is confusing, convert it to be millisecond based. And
thus remove those unnecessary call to msecs_to_jiffies() at runtime for
this field. Other constants are converted assuming HZ == 100, which are
basically true for those platforms.
The assignment in csb726.c was incorrect, and is fixed in this patch as
a result.
Signed-off-by: Eric Miao <eric.y.miao@gmail.com>
Acked-by: Robert Jarzmik <robert.jarzmik@free.fr>
Acked-by: Marc Zyngier <maz@misterjones.org>
Acked-by: Marek Vasut <marek.vasut@gmail.com>
Acked-by: Mike Rapoport <mike@compulab.co.il>
Acked-by: Daniel Mack <daniel@caiaq.de>
|
|
The touchscreen GPIO IRQ was used as a magic number. Define it properly in the
board header file. This is a simple cleanup patch.
Signed-off-by: Marek Vasut <marek.vasut@gmail.com>
Signed-off-by: Eric Miao <eric.y.miao@gmail.com>
|
|
This patch adds support for the on-board IDE channel. I tested this with a CDROM
connected over 2.5-3.5 IDE reduction with external power supplied to the CDROM.
This was not tested with the Voipac 270-HDD-000 (official Voipac HDD module),
but I expect no problems.
Signed-off-by: Marek Vasut <marek.vasut@gmail.com>
Signed-off-by: Eric Miao <eric.y.miao@gmail.com>
|
|
Signed-off-by: Marek Vasut <marek.vasut@gmail.com>
Signed-off-by: Eric Miao <eric.y.miao@gmail.com>
|
|
NOTE:
I wasn't able to get it running without reseting the HXOE (so it's there based
on my tests with the hardware). I'll have to investigate it properly when I have
more time.
Signed-off-by: Marek Vasut <marek.vasut@gmail.com>
Reviewed-by: Robert Jarzmik <robert.jarzmik@free.fr>
Signed-off-by: Eric Miao <eric.y.miao@gmail.com>
|
|
PCMCIA support for Voipac PXA270
Signed-off-by: Marek Vasut <marek.vasut@gmail.com>
Signed-off-by: Eric Miao <eric.y.miao@gmail.com>
|
|
This patch adds basic support for the Voipac PXA270 SBC.
The device consists of the following hardware:
- PXA270 @ 520 MHz
- 256MB RAM (sparsemem, 2*128MB regions)
- 64MB NOR flash
- 640x480 LCD
- Ports: 2xUHC, 1xUDC, 1xPCMCIA, VGA, FFUART, 2xPS2, Speaker, MIC
Signed-off-by: Marek Vasut <marek.vasut@gmail.com>
Signed-off-by: Eric Miao <eric.y.miao@gmail.com>
|
|
This patch adds support for the Zipit Z2. The parts missing from this
patch are the battery support, SPI driver for the LCD and support for
the Silicon Serial ID chip.
Signed-off-by: Marek Vasut <marek.vasut@gmail.com>
Signed-off-by: Eric Miao <eric.y.miao@gmail.com>
|
|
Signed-off-by: Eric Miao <eric.y.miao@gmail.com>
|
|
Tosa is now able to use generic matrix keypad driver instead of the deprecated
tosakbd.c, where CONFIG_KEYBOARD_TOSA_USE_EXT_KEYCODES is still useful. Move
it to mach/Kconfig.
Signed-off-by: Eric Miao <eric.y.miao@gmail.com>
|
|
Some pins are expected to keep their last level during suspend, and
introduce MFP_LPM_KEEP_OUTPUT for this.
Signed-off-by: Eric Miao <eric.y.miao@gmail.com>
|
|
Signed-off-by: Haojian Zhuang <haojian.zhuang@marvell.com>
Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Eric Miao <eric.y.miao@gmail.com>
|
|
No need to separate them as they should be together from the begining.
Signed-off-by: Eric Miao <eric.y.miao@gmail.com>
|
|
The previous definitions of SSCR0_SCR and SSCR0_SerClkDiv() prevented
them being used simultaneously when supporting multiple PXA SoCs, esp.
in drivers/spi/pxa2xx_spi.c, make them correct.
The change from SSCR0_SerClkDiv(2) to SSCR0_SCR(2), will make the result
a little bit different in pxa2xx_spi_probe(), however, since that's only
used as a default initialization value, it's acceptable.
Signed-off-by: Eric Miao <eric.y.miao@gmail.com>
|
|
Signed-off-by: Eric Miao <eric.y.miao@gmail.com>
|
|
The only use of corgi_ssp.c is corgi_ts.c, which is now deprecated
and removed. Remove corgi_ssp.c and corgi_lcd.c and their relevant
function declarations and data structures.
Signed-off-by: Eric Miao <eric.y.miao@gmail.com>
Cc: Richard Purdie <rpurdie@rpsys.net>
Cc: Pavel Machek <pavel@ucw.cz>
|
|
The use of mfp_cfg_t causes build errors without including <mach/mfp.h>.
CC: stable@kernel.org
CC: Daniel Mack <daniel@caiaq.de>
Signed-off-by: Jakob Viketoft <jakob.viketoft@bitsim.com>
Signed-off-by: Eric Miao <eric.y.miao@gmail.com>
|
|
Fix the wrong variable used in cpu_is_pxa950().
Signed-off-by: Haojian Zhuang <haojian.zhuang@marvell.com>
Signed-off-by: Eric Miao <eric.y.miao@gmail.com>
|
|
Signed-off-by: Igor Grinberg <grinberg@compulab.co.il>
Signed-off-by: Eric Miao <eric.y.miao@gmail.com>
|
|
Due to commit:
5de813b ARM: Eliminate decompressor -Dstatic= PIC hack
The data section will be discarded for the decompressor, thus move the
static variables into BSS section by initializing them at run time.
Signed-off-by: Jonathan Cameron <jic23@cam.ac.uk>
Signed-off-by: Eric Miao <eric.y.miao@gmail.com>
|
|
* 'for-linus' of master.kernel.org:/home/rmk/linux-2.6-arm: (370 commits)
ARM: S3C2443: Add set_rate and round_rate calls for armdiv clock
ARM: S3C2443: Remove #if 0 for clk_mpll
ARM: S3C2443: Update notes on MPLLREF clock
ARM: S3C2443: Further clksrc-clk conversions
ARM: S3C2443: Change to using plat-samsung clksrc-clk implementation
USB: Fix s3c-hsotg build following Samsung platform header moves
ARM: S3C64XX: Reintroduce unconditional build of audio device
ARM: 5961/1: ux500: fix CLKRST addresses
ARM: 5977/1: arm: Enable backtrace printing on oops when PC is corrupted
ASoC: Fix S3C64xx IIS driver for Samsung header reorg
ARM: S3C2440: Fix plat-s3c24xx move of s3c2440/s3c2442 support
[ARM] pxa: fix typo in mxm8x10.h
[ARM] pxa/raumfeld: set GPIO drive bits for LED pins
[ARM] pxa/zeus: Add support for mcp2515 CAN bus
[ARM] pxa/zeus: Add support for onboard max6369 watchdog
[ARM] pxa/zeus: Add Eurotech as the manufacturer
[ARM] pxa/zeus: Correct the USB host initialisation flags
[ARM] pxa/zeus: Allow usage of 8250-compatible UART in uncompress
[ARM] pxa: refactor uncompress.h for non-PXA uarts
[ARM] mmp2: fix incorrect calling of chip->mask_ack() for 2nd level cascaded IRQs
...
|
|
This converts arm to the generic pci_set_dma_mask and
pci_set_consistent_dma_mask (removes HAVE_ARCH_PCI_SET_DMA_MASK for
dmabounce).
Signed-off-by: FUJITA Tomonori <fujita.tomonori@lab.ntt.co.jp>
Looked-over-by: Russell King <rmk+kernel@arm.linux.org.uk>
Cc: Jesse Barnes <jbarnes@virtuousgeek.org>
Cc: Greg KH <greg@kroah.com>
Cc: Kay Sievers <kay.sievers@vrfy.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
Conflicts:
arch/arm/mach-mx2/devices.c
arch/arm/mach-mx2/devices.h
sound/soc/pxa/pxa-ssp.c
|
|
Signed-off-by: Eric Miao <eric.y.miao@gmail.com>
|
|
Signed-off-by: Marc Zyngier <maz@misterjones.org>
Signed-off-by: Eric Miao <eric.y.miao@gmail.com>
|
|
Signed-off-by: Marc Zyngier <maz@misterjones.org>
Signed-off-by: Eric Miao <eric.y.miao@gmail.com>
|
|
Zeus console port is wired to a 8250-compatible device (pxa UARTs are
reserved to other uses). This patch allows such a configuration in the
uncompress sequence.
Signed-off-by: Marc Zyngier <maz@misterjones.org>
Signed-off-by: Eric Miao <eric.y.miao@gmail.com>
|
|
The original patch came from Marc Zyngier where support of 8250-compatible
UART is required to show the uncompress information. Modified a little bit
here, including changes below:
1. #include <mach/regs-uart.h> is actually not necessary
2. introduced uart_{read,write}() for different base and shift
3. introduced uart_is_enabled() and assumed enabled always for
non-PXA uarts
Signed-off-by: Eric Miao <eric.y.miao@gmail.com>
Acked-by: Marc Zyngier <maz@misterjones.org>
|
|
Signed-off-by: Eric Miao <eric.y.miao@gmail.com>
|
|
Signed-off-by: Edwin Peer <epeer@tmtservices.co.za>
Signed-off-by: Eric Miao <eric.y.miao@gmail.com>
|
|
Signed-off-by: Eric Miao <eric.y.miao@gmail.com>
|
|
Signed-off-by: Eric Miao <eric.y.miao@gmail.com>
|
|
Signed-off-by: Eric Miao <eric.y.miao@gmail.com>
|
|
IRQ_LOCOMO_* are never used elsewhere, remove these definitions. As well
as the cascade of these IRQs. IRQ_LOCOMO_*_BASE changed to IRQ_LOCOMO_*.
IRQ_LOCOMO_LT and IRQ_LOCOMO_SPI are likely to be used in a same way as
IRQ_LOCOMO_KEY.
IRQ_LOCOMO_GPIO and the demultiplex handler should really be living
somewhere else.
Signed-off-by: Eric Miao <eric.y.miao@gmail.com>
|
|
It is not necessary and is over-complicated for IRQ_LOCOMO_KEY to
be a cascaded IRQ of IRQ_LOCOMO_KEY_BASE. Removed and introduced
locomokbd_{open,close} for masking/unmasking of the keyboard IRQ.
Signed-off-by: Eric Miao <eric.y.miao@gmail.com>
|
|
Signed-off-by: Eric Miao <eric.y.miao@gmail.com>
|
|
There are only limited possible LCD pin configurations for pxa25x
platforms, simplify this by macro.
Signed-off-by: Eric Miao <eric.y.miao@gmail.com>
|
|
* 'for-linus' of master.kernel.org:/home/rmk/linux-2.6-arm: (100 commits)
ARM: Eliminate decompressor -Dstatic= PIC hack
ARM: 5958/1: ARM: U300: fix inverted clk round rate
ARM: 5956/1: misplaced parentheses
ARM: 5955/1: ep93xx: move timer defines into core.c and document
ARM: 5954/1: ep93xx: move gpio interrupt support to gpio.c
ARM: 5953/1: ep93xx: fix broken build of clock.c
ARM: 5952/1: ARM: MM: Add ARM_L1_CACHE_SHIFT_6 for handle inside each ARCH Kconfig
ARM: 5949/1: NUC900 add gpio virtual memory map
ARM: 5948/1: Enable timer0 to time4 clock support for nuc910
ARM: 5940/2: ARM: MMCI: remove custom DBG macro and printk
ARM: make_coherent(): fix problems with highpte, part 2
MM: Pass a PTE pointer to update_mmu_cache() rather than the PTE itself
ARM: 5945/1: ep93xx: include correct irq.h in core.c
ARM: 5933/1: amba-pl011: support hardware flow control
ARM: 5930/1: Add PKMAP area description to memory.txt.
ARM: 5929/1: Add checks to detect overlap of memory regions.
ARM: 5928/1: Change type of VMALLOC_END to unsigned long.
ARM: 5927/1: Make delimiters of DMA area globally visibly.
ARM: 5926/1: Add "Virtual kernel memory..." printout.
ARM: 5920/1: OMAP4: Enable L2 Cache
...
Fix up trivial conflict in arch/arm/mach-mx25/clock.c
|
|
pxa_camera init() callback is sometimes abused to setup MFP for PXA CIF, or
even to request GPIOs to be used by the camera *sensor*. These initializations
can be performed statically in machine init functions.
The current semantics for this init() callback is ambiguous anyways, it is
invoked in pxa_camera_activate(), hence at device node open, but its users use
it like a generic initialization to be done at module init time (configure
MFP, request GPIOs for *sensor* control).
Signed-off-by: Antonio Ospite <ospite@studenti.unina.it>
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
|
|
|
|
Makes it consistent with VMALLOC_START
Tested-by: H Hartley Sweeten <hsweeten@visionengravers.com>
Signed-off-by: Andreas Fenkart <andreas.fenkart@streamunlimited.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
|
|
Otherwise more complicated uart configuration won't be possible.
We can use r1 for tmp register for both head.S and debug.S.
NOTE: This patch depends on another patch to add the the tmp register
into all debug-macro.S files. That can be done with:
$ sed -i -e "s/addruart,rx|addruart, rx/addruart, rx, tmp/"
arch/arm/*/include/*/debug-macro.S
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
|
|
GPIO89_AC97_nRESET is really a PXA26x specific option and was
incorrectly named.
Signed-off-by: Eric Miao <eric.y.miao@gmail.com>
|
|
Signed-off-by: Eric Miao <eric.y.miao@gmail.com>
|
|
PXA mmc host driver supports card detect, read only and power gpio pin
setting already. Zylonite platform driver needn't implement this any more.
Signed-off-by: Haojian Zhuang <haojian.zhuang@marvell.com>
Signed-off-by: Eric Miao <eric.y.miao@gmail.com>
|
|
The Arcom Zeus CF slot requires the same kind of support as the Viper.
To avoid code duplication, introduce a platform device that abstracts
the differences.
This also allows for the removal of the ugly export of viper_cf_rst().
Signed-off-by: Marc Zyngier <maz@misterjones.org>
Signed-off-by: Eric Miao <eric.y.miao@gmail.com>
|
|
Signed-off-by: Marc Zyngier <maz@misterjones.org>
Signed-off-by: Eric Miao <eric.y.miao@gmail.com>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/jikos/trivial
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jikos/trivial: (42 commits)
tree-wide: fix misspelling of "definition" in comments
reiserfs: fix misspelling of "journaled"
doc: Fix a typo in slub.txt.
inotify: remove superfluous return code check
hdlc: spelling fix in find_pvc() comment
doc: fix regulator docs cut-and-pasteism
mtd: Fix comment in Kconfig
doc: Fix IRQ chip docs
tree-wide: fix assorted typos all over the place
drivers/ata/libata-sff.c: comment spelling fixes
fix typos/grammos in Documentation/edac.txt
sysctl: add missing comments
fs/debugfs/inode.c: fix comment typos
sgivwfb: Make use of ARRAY_SIZE.
sky2: fix sky2_link_down copy/paste comment error
tree-wide: fix typos "couter" -> "counter"
tree-wide: fix typos "offest" -> "offset"
fix kerneldoc for set_irq_msi()
spidev: fix double "of of" in comment
comment typo fix: sybsystem -> subsystem
...
|
|
Conflicts:
kernel/irq/chip.c
|
