| Age | Commit message (Collapse) | Author |
|---|
|
The Cragganmore system is modular with I2C based identification chips on
the system allowing identification of the system build. Provide a stub I2C
driver which parses the module IDs and uses them to select the appropriate
audio subsystem components to register. To avoid confusion due to having
the mini-driver in the system the driver is placed in a separate file.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/arm/linux-arm-soc
* 'next/board' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/linux-arm-soc:
ARM: S3C64XX: Configure backup battery charger on Cragganmore
ARM: S3C64XX: Fix WM8915 IRQ polarity on Cragganmore
ARM: S3C64XX: Configure supplies for all Cragganmore regulators
ARM: S3C64XX: Refresh Cragganmore support
ARM: S3C64XX: Initial support for Wolfson/Simtec Cragganmore/Banff
OMAP4: Keyboard: Mux changes in the board file
omap: blaze: add mmc5/wl1283 device support
omap: 4430SDP: Register the card detect GPIO properly
arm: omap3: cm-t35: add support for cm-t3730
OMAP3: beagle: add support for beagleboard xM revision C
OMAP3: rx-51: Add full regulator definitions
omap: rx51: Platform support for lp5523 led chip
|
|
This patch adds support for LCD backlight using PWM timer for
Samsung SMDK6410 board.
Signed-off-by: Banajit Goswami <banajit.g@samsung.com>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
|
|
The Cragganmore carrier card and Banff CPU module are used on Wolfson
Microelectronics reference systems. This initial support covers the
core system which is a fairly generic S3C6410 based design, further
patches will add support for the key features of the reference system.
The initial board bringup and therefore much of the key code was done by
Ben Dooks for Simtec, with additional work (especially around the
integration of the Wolfson devices) being done by myself.
Signed-off-by: Ben Dooks <ben@simtec.co.uk>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
[kgene.kim@samsung.com: removed inclusion of <mach/regs-fb.h>]
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
|
|
This patch adds support for LCD backlight using PWM timer for
Samsung SMDK6410 board.
Signed-off-by: Banajit Goswami <banajit.g@samsung.com>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
|
|
This patch does the following:-
1. It moves file pwm.c from plat-s3c24xx to plat-samsung. This will
enable all machines with Samsung SoCs to make use of the same code.
2. The device definitions have been separated to a new file dev-pwm.c
for better clarity and structure.
3. It will enable all Samsung S3C and S5P series SoC's to use common
PWM Kconfig definition.
Signed-off-by: Banajit Goswami <banajit.g@samsung.com>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
|
|
Fix build warnings
warning: (ARCH_S3C64XX && <choice> && WATCHDOG || ARCH_S5P64X0 && <choice> && WATCHDOG ||
ARCH_S5P6442 && <choice> && WATCHDOG || ARCH_S5PC100 && <choice> ||
ARCH_S5PV210 && <choice> || ARCH_S5PV310 && <choice> || MACH_SMDK6410 && ARCH_S3C64XX)
selects HAVE_S3C2410_WATCHDOG which has unmet direct dependencies (WATCHDOG)
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
[kgene.kim@samsung.com: Added fix same warning(mach-s3c64xx/Kconfig)]
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
|
|
* 'devel' of master.kernel.org:/home/rmk/linux-2.6-arm: (215 commits)
ARM: memblock: setup lowmem mappings using memblock
ARM: memblock: move meminfo into find_limits directly
ARM: memblock: convert free_highpages() to use memblock
ARM: move freeing of highmem pages out of mem_init()
ARM: memblock: convert memory detail printing to use memblock
ARM: memblock: use memblock to free memory into arm_bootmem_init()
ARM: memblock: use memblock when initializing memory allocators
ARM: ensure membank array is always sorted
ARM: 6466/1: implement flush_icache_all for the rest of the CPUs
ARM: 6464/2: fix spinlock recursion in adjust_pte()
ARM: fix memblock breakage
ARM: 6465/1: Fix data abort accessing proc_info from __lookup_processor_type
ARM: 6460/1: ixp2000: fix type of ixp2000_timer_interrupt
ARM: 6449/1: Fix for compiler warning of uninitialized variable.
ARM: 6445/1: fixup TCM memory types
ARM: imx: Add wake functionality to GPIO
ARM: mx5: Add gpio-keys to mx51 babbage board
ARM: imx: Add gpio-keys to plat-mxc
mx31_3ds: Fix spi registration
mx31_3ds: Fix the logic for detecting the debug board
...
|
|
In preparation for the addition of SPI support for the WM831x move the I2C
specific code into a separate file with a separate Kconfig option so the
I2C support can be excluded from the build.
Also update the 1133-EV1 PMIC module support for SMDK6410 to use the new
symbol.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
|
|
Add touchscreen device support for mach-mini6410
Signed-off-by: Darius Augulis <augulis.darius@gmail.com>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
|
|
Add support for frame buffer device for mach-mini6410.
Patch also adds support for feature string parsing
for mini6410. The feature string is kernel command
line passed and currently lets select only LCD
configuration. At the moment there is support for
two LCD configurations - 4.3" and 7.0". Feature
parser is mach-mini2440 based.
Signed-off-by: Darius Augulis <augulis.darius@gmail.com>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
|
|
Add nand device support and mtd partition
table for mini6410
Signed-off-by: Darius Augulis <augulis.darius@gmail.com>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
|
|
Add support for mini6410 board from FriendlyARM
Signed-off-by: Darius Augulis <augulis.darius@gmail.com>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
|
|
Add USB host device support for mach-real6410
Signed-off-by: Darius Augulis <augulis.darius@gmail.com>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
|
|
Add touchscreen device support for mach-real6410
Signed-off-by: Darius Augulis <augulis.darius@gmail.com>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
|
|
Add nand device support and mtd partition table
for mach-real6410
Signed-off-by: Darius Augulis <augulis.darius@gmail.com>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
|
|
Add support for frame buffer device for mach-real6410.
Patch also adds support for feature string parsing
for real6410. The feature string is kernel command
line passed and currently lets select only LCD
configuration. At the moment there is support for
two LCD configurations - 4.3" and 7.0". Feature
parser is mach-mini2440 based.
Signed-off-by: Darius Augulis <augulis.darius@gmail.com>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
|
|
* 'for-linus/samsung-2635' of git://git.fluff.org/bjdooks/linux:
DMAENGINE: correct PL080 register header file
ARM: SAMSUNG: Fix on build warning about dependency in Kconfig
ARM: SMDK6410: Make virtual screen twice depth of real
ARM: S3C64XX: Update consistent DMA size to 8MiB
ARM: S3C64XX: Add audio support to SmartQ
ARM: S3C64XX: Framebuffer fix for SmartQ5
ARM: S3C64XX: Set wifi and iNAND as permanently connected SD devices on SmartQ boards
ARM: S3C64XX: Move SmartQ LCD control platform definition to shared file
ARM: mach-real6410: add sdhc device support
ARM: mach-real6410: add dm9000 ethernet support for mach-real6410
ARM: S3C64XX: Support for Real6410
Fix up trivial conflicts in arch/arm/mach-s3c64xx/mach-smartq5.c
("remove pixclock" vs "Framebuffer fix for SmartQ5")
|
|
Register SHDCI devices
Signed-off-by: Darius Augulis <augulis.darius@gmail.com>
[ben-linux@fluff.org: rewrite header[
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
|
|
Add support for CoreWind Real6410 board, based on Samsung s3c6410 processor.
Signed-off-by: Darius Augulis <augulis.darius@gmail.com>
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
|
|
This patch is to support keypad device to the SMDK6410 board.
Signed-off-by: Naveen Krishna Ch <ch.naveen@samsung.com>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
|
|
This patch adds support for RTC for SMDK6410.
Signed-off-by: Atul Dahiya <atul.dahiya@samsung.com>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
|
|
Following is added for the CF-ATA driver:
- Platform data strucure instantiation
- Platform device enabling code
- Addition of cfcon clock
- Platform-specific gpio setup code
Signed-off-by: Abhilash Kesavan <a.kesavan@samsung.com>
Signed-off-by: Thomas Abraham <thomas.ab@samsung.com>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
|
|
Use the new wakeup mask synchronisation code to set the
relevant wakeup mask bits.
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
|
|
Merge branch 'for-2635-4/onenand' into for-2635-4/partial2
Conflicts:
arch/arm/mach-s5pc100/cpu.c
arch/arm/mach-s5pc100/include/mach/map.h
arch/arm/mach-s5pv210/Makefile
|
|
Merge branch 'for-2635-4/watchdog' into for-2635-4/partial2
Conflicts:
arch/arm/mach-s3c64xx/mach-smdk6410.c
arch/arm/mach-s5p6440/Kconfig
arch/arm/mach-s5p6440/include/mach/map.h
arch/arm/mach-s5p6440/mach-smdk6440.c
arch/arm/mach-s5pv210/Kconfig
arch/arm/mach-s5pv210/include/mach/map.h
arch/arm/mach-s5pv210/mach-smdkv210.c
|
|
This patch adds support for Watchdog timer for Samsung S3C6410
Signed-off-by: Banajit Goswami <banajit.g@samsung.com>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
|
|
This adds new machine definitions for the SmartQ 5 and 7.
Signed-off-by: Maurus Cuelenaere <mcuelenaere@gmail.com>
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
|
|
This patch adds setup code for Samsung OneNAND controller driver. The
driver needs to be aware on which SoC it is running, so the actual
device id is being changed in cpu init code. S3C64xx SoCs have 2 OneNAND
controllers while S5PC100 and S5PC110 has only one.
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
[ben-linux@fluff.org: sort map.h entries]
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
|
|
This patch adds touchscreen support for S3C64XX.
Signed-off-by: Naveen Krishna Ch <ch.naveen@samsung.com>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
[ben-linux@fluff.org: minor title fix]
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
|
|
This patch moves ADC device definition to plat-samsung.
Because that is generic to the S3C64XX and S5P Series SoCs.
Signed-off-by: Naveen Krishna Ch <ch.naveen@samsung.com>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
|
|
The Wolfson Microelectronics 1192-EV1 is a plug in module for the
SMDK6410 providing power using a WM8312 PMIC. This patch provides
initial hookup sufficient to initialise the board, though not all
features are fully described yet.
As part of this supplies for the system that are provided as a
single supply by one of the currently merged PMIC boards are
factored out so they can be reused between different regulators.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
|
|
Now we've move the support out of plat-s3c64xx for everything, eliminate
the platform directory arch/arm/plat-s3c64xx and remove it from the ARM
build configuration.
Note, PLAT_S3C64XX is kept around for the moment until the drivers that
depend on it can be updated, so it is moved to the mach-s3c64xx Kconfig.
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
|
|
Merge plat-s3c64xx/s3c6400-clock.c mach-s3c64xx/clock.c placing all the
clock code into one place.
Note, no effort is made in this patch to squash the init functions
together.
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
|
|
Since this file is small, and is compiled for both systems in this
architecture merge it into the cpu support file and remove the original
instead of moving it.
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
|
|
Move the core S3C64XX support to mach-s3c64xx as it is unlikely to be used
outside of this directory. Also move the SoC header files in with it.
This includes the clock, cpu, cpufreq, dma, gpiolib and pll support.
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
|
|
Move the S3C64XX specific device and setup files into mach-s3c64xx as
they are unlikely to be used outside of this code.
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
|
|
Squash the SDHCI setup for both the S3C6400 and S3C6410 into one file and
make the S3C6410 case use the S3C6400 code.
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
|
|
As per discussions with Russell King on linux-arm-kernel, it appears that
both mach-s3c6400 and mach-s3c6410 are so close together that they should
simply be merged into mach-s3c64xx.
Note, this patch does not eliminate any of the bits that are still common,
it is simply a move of the two directories together, any further common
code will be eliminated or moved in further patches.
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
|
