| Age | Commit message (Collapse) | Author |
|---|
|
commit 1e5e929c009559bd7e898ac8e17a5d01037cb057 upstream.
Commit 34993594181d ("arm64: tegra: Enable HDMI on Jetson TX1")
added a regulator for HDMI on the Jetson TX1 platform. This regulator
has an active high enable, but the GPIO specifier for enabling the
regulator incorrectly defines it as active-low. This causes the
following warning to occur on boot ...
WARNING KERN regulator@10 GPIO handle specifies active low - ignored
The fixed-regulator binding does not use the active-low flag from the
gpio specifier and purely relies of the presence of the
'enable-active-high' property to determine if it is active high or low
(if this property is omitted). Fix this warning by setting the GPIO
to active-high in the GPIO specifier which aligns with the presense of
the 'enable-active-high' property.
Fixes: 34993594181d ("arm64: tegra: Enable HDMI on Jetson TX1")
Signed-off-by: Jon Hunter <jonathanh@nvidia.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
[ Upstream commit 6ff7705da8806de45ca1490194f0b4eb07725804 ]
On p2180 sdmmc4 is powered from a fixed 1.8 V regulator.
Signed-off-by: Aapo Vienamo <avienamo@nvidia.com>
Reviewed-by: Mikko Perttunen <mperttunen@nvidia.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
commit ba24eee6686f6ed3738602b54d959253316a9541 upstream.
The Tegra AGIC interrupt controller is an ARM GIC400 interrupt
controller. Per the ARM GIC device-tree binding, the first address
region is for the GIC distributor registers and the second address
region is for the GIC CPU interface registers. The address space for
the distributor registers is 4kB, but currently this is incorrectly
defined as 8kB for the Tegra AGIC and overlaps with the CPU interface
registers. Correct the address space for the distributor to be 4kB.
Cc: stable@vger.kernel.org
Signed-off-by: Jon Hunter <jonathanh@nvidia.com>
Fixes: bcdbde433542 ("arm64: tegra: Add AGIC node for Tegra210")
Signed-off-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit ece6031ece2dd64d63708cfe1088016cee5b10c0 upstream.
The GPU regulator enable ramp delay for Jetson TX1 is set to 1ms which
not sufficient because the enable ramp delay has been measured to be
greater than 1ms. Furthermore, the downstream kernels released by NVIDIA
for Jetson TX1 are using a enable ramp delay 2ms and a settling delay of
160us. Update the GPU regulator enable ramp delay for Jetson TX1 to be
2ms and add a settling delay of 160us.
Cc: stable@vger.kernel.org
Signed-off-by: Jon Hunter <jonathanh@nvidia.com>
Fixes: 5e6b9a89afce ("arm64: tegra: Add VDD_GPU regulator to Jetson TX1")
Signed-off-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
[ Upstream commit 9df50ba76ac1485b844beffa1f3f5d9659d9cdaf ]
Need to configure PHY interrupt as active low for P3310 Tegra186
platform otherwise it results in spurious interrupts.
This issue wasn't seen before because the generic PHY driver without
interrupt support was used.
Signed-off-by: Bhadram Varka <vbhadram@nvidia.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Many source files in the tree are missing licensing information, which
makes it harder for compliance tools to determine the correct license.
By default all files without license information are under the default
license of the kernel, which is GPL version 2.
Update the files which contain no license information with the 'GPL-2.0'
SPDX license identifier. The SPDX identifier is a legally binding
shorthand, which can be used instead of the full boiler plate text.
This patch is based on work done by Thomas Gleixner and Kate Stewart and
Philippe Ombredanne.
How this work was done:
Patches were generated and checked against linux-4.14-rc6 for a subset of
the use cases:
- file had no licensing information it it.
- file was a */uapi/* one with no licensing information in it,
- file was a */uapi/* one with existing licensing information,
Further patches will be generated in subsequent months to fix up cases
where non-standard license headers were used, and references to license
had to be inferred by heuristics based on keywords.
The analysis to determine which SPDX License Identifier to be applied to
a file was done in a spreadsheet of side by side results from of the
output of two independent scanners (ScanCode & Windriver) producing SPDX
tag:value files created by Philippe Ombredanne. Philippe prepared the
base worksheet, and did an initial spot review of a few 1000 files.
The 4.13 kernel was the starting point of the analysis with 60,537 files
assessed. Kate Stewart did a file by file comparison of the scanner
results in the spreadsheet to determine which SPDX license identifier(s)
to be applied to the file. She confirmed any determination that was not
immediately clear with lawyers working with the Linux Foundation.
Criteria used to select files for SPDX license identifier tagging was:
- Files considered eligible had to be source code files.
- Make and config files were included as candidates if they contained >5
lines of source
- File already had some variant of a license header in it (even if <5
lines).
All documentation files were explicitly excluded.
The following heuristics were used to determine which SPDX license
identifiers to apply.
- when both scanners couldn't find any license traces, file was
considered to have no license information in it, and the top level
COPYING file license applied.
For non */uapi/* files that summary was:
SPDX license identifier # files
---------------------------------------------------|-------
GPL-2.0 11139
and resulted in the first patch in this series.
If that file was a */uapi/* path one, it was "GPL-2.0 WITH
Linux-syscall-note" otherwise it was "GPL-2.0". Results of that was:
SPDX license identifier # files
---------------------------------------------------|-------
GPL-2.0 WITH Linux-syscall-note 930
and resulted in the second patch in this series.
- if a file had some form of licensing information in it, and was one
of the */uapi/* ones, it was denoted with the Linux-syscall-note if
any GPL family license was found in the file or had no licensing in
it (per prior point). Results summary:
SPDX license identifier # files
---------------------------------------------------|------
GPL-2.0 WITH Linux-syscall-note 270
GPL-2.0+ WITH Linux-syscall-note 169
((GPL-2.0 WITH Linux-syscall-note) OR BSD-2-Clause) 21
((GPL-2.0 WITH Linux-syscall-note) OR BSD-3-Clause) 17
LGPL-2.1+ WITH Linux-syscall-note 15
GPL-1.0+ WITH Linux-syscall-note 14
((GPL-2.0+ WITH Linux-syscall-note) OR BSD-3-Clause) 5
LGPL-2.0+ WITH Linux-syscall-note 4
LGPL-2.1 WITH Linux-syscall-note 3
((GPL-2.0 WITH Linux-syscall-note) OR MIT) 3
((GPL-2.0 WITH Linux-syscall-note) AND MIT) 1
and that resulted in the third patch in this series.
- when the two scanners agreed on the detected license(s), that became
the concluded license(s).
- when there was disagreement between the two scanners (one detected a
license but the other didn't, or they both detected different
licenses) a manual inspection of the file occurred.
- In most cases a manual inspection of the information in the file
resulted in a clear resolution of the license that should apply (and
which scanner probably needed to revisit its heuristics).
- When it was not immediately clear, the license identifier was
confirmed with lawyers working with the Linux Foundation.
- If there was any question as to the appropriate license identifier,
the file was flagged for further research and to be revisited later
in time.
In total, over 70 hours of logged manual review was done on the
spreadsheet to determine the SPDX license identifiers to apply to the
source files by Kate, Philippe, Thomas and, in some cases, confirmation
by lawyers working with the Linux Foundation.
Kate also obtained a third independent scan of the 4.13 code base from
FOSSology, and compared selected files where the other two scanners
disagreed against that SPDX file, to see if there was new insights. The
Windriver scanner is based on an older version of FOSSology in part, so
they are related.
Thomas did random spot checks in about 500 files from the spreadsheets
for the uapi headers and agreed with SPDX license identifier in the
files he inspected. For the non-uapi files Thomas did random spot checks
in about 15000 files.
In initial set of patches against 4.14-rc6, 3 files were found to have
copy/paste license identifier errors, and have been fixed to reflect the
correct identifier.
Additionally Philippe spent 10 hours this week doing a detailed manual
inspection and review of the 12,461 patched files from the initial patch
version early this week with:
- a full scancode scan run, collecting the matched texts, detected
license ids and scores
- reviewing anything where there was a license detected (about 500+
files) to ensure that the applied SPDX license was correct
- reviewing anything where there was no detection but the patch license
was not GPL-2.0 WITH Linux-syscall-note to ensure that the applied
SPDX license was correct
This produced a worksheet with 20 files needing minor correction. This
worksheet was then exported into 3 different .csv files for the
different types of files to be modified.
These .csv files were then reviewed by Greg. Thomas wrote a script to
parse the csv files and add the proper SPDX tag to the file, in the
format that the file expected. This script was further refined by Greg
based on the output to detect more types of files automatically and to
distinguish between header and source .c files (which need different
comment types.) Finally Greg ran the script using the .csv files to
generate the patches.
Reviewed-by: Kate Stewart <kstewart@linuxfoundation.org>
Reviewed-by: Philippe Ombredanne <pombredanne@nexb.com>
Reviewed-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
dtc recently added PCI bus checks. Fix these warnings.
Signed-off-by: Rob Herring <robh@kernel.org>
Cc: Stephen Warren <swarren@wwwdotorg.org>
Cc: Thierry Reding <thierry.reding@gmail.com>
Cc: Alexandre Courbot <gnurou@gmail.com>
Cc: linux-tegra@vger.kernel.org
Signed-off-by: Thierry Reding <treding@nvidia.com>
|
|
The Tegra186 CCPLEX_CLUSTER area contains memory-mapped
registers that initiate CPU frequency/voltage transitions.
Signed-off-by: Mikko Perttunen <mperttunen@nvidia.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
|
|
Update the Tegra132 flowctrl compatible string to include
"nvidia,tegra132-flowctrl" so it is aligned with the flowctrl binding
documentation.
Signed-off-by: Jon Hunter <jonathanh@nvidia.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
|
|
Add the DT node for the GP10B GPU on Tegra186.
Signed-off-by: Alexandre Courbot <acourbot@nvidia.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
|
|
The host1x driver now supports operation behind an IOMMU, so add its
IOMMU domain to the device tree.
Signed-off-by: Mikko Perttunen <mperttunen@nvidia.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
|
|
Enable the VIC (Video Image Compositor) host1x unit on Tegra210 systems.
Signed-off-by: Mikko Perttunen <mperttunen@nvidia.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
|
|
The P2771 development board expands the number of GPIOs via two I2C
chips.
Acked-by: Jon Hunter <jonathanh@nvidia.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
|
|
The P2771 development board comes with two power monitors that can be
used to determine power consumption in different parts of the board.
Acked-by: Jon Hunter <jonathanh@nvidia.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
|
|
The P2771 has three keys (power, volume up and volume down) that are
connected to pins on the AON GPIO controller.
Acked-by: Jon Hunter <jonathanh@nvidia.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
|
|
The P3310 processor module contains two current monitors that can be
used to determine the current flow across various parts of the board
design.
Acked-by: Jon Hunter <jonathanh@nvidia.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
|
|
The P3310 processor module makes provisions for exposing the SDMMC1
controller via a standard SD/MMC slot, which the P2771 supports. Hook
up the power supply provided on the P2771 carrier board and enable
the device tree node.
Acked-by: Jon Hunter <jonathanh@nvidia.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
|
|
The P3110 processor module wires one of the SDHCI controllers to an on-
board eMMC and exposes another set of SD/MMC signals on the connector to
support an external SD/MMC card. A third controller is connected to the
SDIO pins of an M.2 KEY E connector.
Acked-by: Jon Hunter <jonathanh@nvidia.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
|
|
Enable the Maxim MAX77620 PMIC found on P3310 and add some fixed
regulators to model the power tree.
Acked-by: Jon Hunter <jonathanh@nvidia.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
|
|
The P3310 processor module provides networking via the ethernet
controller found on NVIDIA Tegra186 SoCs.
Acked-by: Jon Hunter <jonathanh@nvidia.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
|
|
The P3310 processor modules use seven I2C controllers for various
peripherals.
Acked-by: Jon Hunter <jonathanh@nvidia.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
|
|
The PMC interrupt is inverted on P3310, so mark it as such in the device
tree to avoid a flood of interrupts when the PMIC is enabled.
Acked-by: Jon Hunter <jonathanh@nvidia.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
|
|
The NVIDIA Tegra186 SoC contains an instance of the Synopsys DWC
ethernet QOS IP block, which supports 10, 100 and 1000 Mbps data
transfer rates.
Acked-by: Jon Hunter <jonathanh@nvidia.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
|
|
The NVIDIA Tegra186 SoC has a Power Management Controller that performs
various tasks related to system power, boot as well as suspend/resume.
Acked-by: Jon Hunter <jonathanh@nvidia.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
|
|
Now that the corresponding device tree binding include has been merged,
convert the DTS files to use symbolic names instead of numeric ones.
Signed-off-by: Thierry Reding <treding@nvidia.com>
|
|
Now that the corresponding device tree binding include has been merged,
convert the DTS files to use symbolic names instead of numeric ones.
Signed-off-by: Thierry Reding <treding@nvidia.com>
|
|
Now that the corresponding device tree binding include has been merged,
convert the DTS files to use symbolic names instead of numeric ones.
Signed-off-by: Thierry Reding <treding@nvidia.com>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM 64-bit DT updates from Arnd Bergmann:
"A couple of interesting new SoC platforms are now supported, these are
the respective DTS sources:
- Samsung Exynos5433 mobile phone platform, including an (almost)
fully supported phone reference board.
- Hisilicon Hip07 server platform and D05 board, the latest iteration
of their product line, now with 64 Cortex-A72 cores across two
sockets.
- Allwinner A64 SoC, the first 64-bit chip from their "sunxi" product
line, used in Android tablets and ultra-cheap development boards
- NXP LS1046A Communication processor, improving on the earlier
LS1043A with faster CPU cores
- Qualcomm MSM8992 (Snapdragon 808) and MSM8994 (Snapdragon 810)
mobile phone SoCs
- Early support for the Nvidia Tegra Tegra186 SoC
- Amlogic S905D is a minor variant of their existing Android consumer
product line
- Rockchip PX5 automotive platform, a close relative of their popular
rk3368 Android tablet chips
Aside from the respective evaluation platforms for the above chips,
there are only a few consumer devices and boards added this time:
- Huawei Nexus 6P (Angler) mobile phone
- LG Nexus 5x (Bullhead) mobile phone
- Nexbox A1 and A95X Android TV boxes
- Pine64 development board based on Allwinner A64
- Globalscale Marvell ESPRESSOBin community board based on Armada 3700
- Renesas "R-Car Starter Kit Pro" (M3ULCB) low-cost automotive board
For the existing platforms, we get bug fixes and new peripheral
support for Juno, Renesas, Uniphier, Amlogic, Samsung, Broadcom,
Rockchip, Berlin, and ZTE"
* tag 'armsoc-dt64' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (168 commits)
arm64: dts: fix build errors from missing dependencies
ARM64: dts: meson-gxbb: add SCPI pre-1.0 compatible
ARM64: dts: meson-gxl: Add support for Nexbox A95X
ARM64: dts: meson-gxm: Add support for the Nexbox A1
ARM: dts: artpec: add pcie support
arm64: dts: berlin4ct-dmp: add missing unit name to /memory node
arm64: dts: berlin4ct-stb: add missing unit name to /memory node
arm64: dts: berlin4ct: add missing unit name to /soc node
arm64: dts: qcom: msm8916: Add ddr support to sdhc1
arm64: dts: exynos: Enable HS400 mode for eMMC for TM2
ARM: dts: Add xo to sdhc clock node on qcom platforms
ARM64: dts: Add support for Meson GXM
dt-bindings: add rockchip RK1108 Evaluation board
arm64: dts: NS2: Add PCI PHYs
arm64: dts: NS2: enable sdio1
arm64: dts: exynos: Add the mshc_2 node for supporting T-Flash
arm64: tegra: Add NVIDIA P2771 board support
arm64: tegra: Enable PSCI on P3310
arm64: tegra: Add NVIDIA P3310 processor module support
arm64: tegra: Add GPIO controllers on Tegra186
...
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM SoC non-urgent fixes from Arnd Bergmann:
"As usual, we queue up a few fixes that don't seem urgent enough to go
in through -rc, or that just came a little too late given their size.
The zx fixes make the platform finally boot on real hardware, the
davinci and imx31 get the DT support working better for some of the
machines that are still normally used with classic board files. One
tegra fix is important for new bootloader versions, but the bug has
been around for a while without anyone noticing.
The other changes are mostly cosmetic"
* tag 'armsoc-fixes-nc' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (22 commits)
arm64: tegra: Add missing Smaug revision
arm64: tegra: Add VDD_GPU regulator to Jetson TX1
arm64: dts: zte: clean up gic-v3 redistributor properties
arm64: dts: zx: Fix gic GICR property
bus: vexpress-config: fix device reference leak
soc: ti: qmss: fix the case when !SMP
ARM: lpc32xx: drop duplicate header device.h
ARM: ixp4xx: drop duplicate header gpio.h
ARM: socfpga: fix spelling mistake in error message
ARM: dts: imx6q-cm-fx6: fix fec pinctrl
ARM: dts: imx7d-pinfunc: fix UART pinmux defines
ARM: dts: imx6qp: correct LDB clock inputs
ARM: OMAP2+: pm-debug: Use seq_putc() in two functions
ARM: OMAP2+: Remove the omapdss_early_init_of() function
mfd: tps65217: Fix mismatched interrupt number
ARM: zx: Fix error handling
ARM: spear: Fix error handling
ARM: davinci: da850: Fix pwm name matching
ARM: clk: imx31: properly init clocks for machines with DT
clk: imx31: fix rewritten input argument of mx31_clocks_init()
...
|
|
The "google,smaug-rev2" string is missing from the compatible list of
Smaug's DT. The differences of rev2 are not relevant at our current
level of support and it boots just fine, so add it.
Signed-off-by: Alexandre Courbot <acourbot@nvidia.com>
Acked-by: Jon Hunter <jonathanh@nvidia.com>
Acked-by: Andrew Bresticker <abrestic@chromium.org>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
|
|
Add the VDD_GPU regulator (a GPIO-enabled PWM regulator) to the Jetson
TX1 board. This addition allows the GPU to be used provided the
bootloader properly enabled the GPU node.
Signed-off-by: Alexandre Courbot <acourbot@nvidia.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
[as pointed out by Thierry on IRC, nobody has reported a bug
in the field, but using a new bootloader with a .dtb that
has the incorrect data, it will crash on boot]
Fixes: 336f79c7b6d7 ("arm64: tegra: Add NVIDIA Jetson TX1 Developer Kit support")
Cc: stable@vger.kernel.org #v4.5+
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
|
|
Enable the x4 PCIe and M.2 Key E slots on Jetson TX1. The Key E slot is
currently untested due to lack of hardware.
Signed-off-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Bjorn Helgaas <helgaas@kernel.org>
|
|
Add the PCIe host bridge found on Tegra X1. It implements two root ports
that support x4 and x1 configurations, respectively.
Signed-off-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Bjorn Helgaas <helgaas@kernel.org>
|
|
The NVIDIA P2771 is composed of a P3310 processor module that connects
to the P2597 I/O board. It comes with a 1200x1920 MIPI DSI panel that is
connected via the P2597's display connector and has several connectors
such as HDMI, USB 3.0, PCIe and ethernet.
Signed-off-by: Joseph Lo <josephl@nvidia.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
|
|
The P3310 processor module comes ships with a firmware that implements
PSCI 1.0. Enable and use it to bring up all CPUs.
Signed-off-by: Thierry Reding <treding@nvidia.com>
|
|
The NVIDIA P3310 is a processor module used in several reference designs
that features a Tegra186 SoC, 8 GiB of LPDDR4 RAM, 32 GiB eMMC and other
essentials such as ethernet, WiFi and a PMIC. It is typically connected
to an I/O board (such as the P2597) that provides the connecters needed
to hook it up to the outside world.
Signed-off-by: Joseph Lo <josephl@nvidia.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
|
|
Tegra186 has two GPIO controllers that are no longer compatible with the
controller found on earlier generations. One of these controllers exists
in an always-on partition of the SoC whereas the other can be clock- and
powergated.
Signed-off-by: Thierry Reding <treding@nvidia.com>
|
|
Tegra186 has a total of four SDHCI controllers that each support SD 4.2
(up to UHS-I speed), SDIO 4.1 (up to UHS-I speed), eSD 2.1, eMMC 5.1 and
SDHOST 4.1 (up to UHS-I speed).
Signed-off-by: Thierry Reding <treding@nvidia.com>
|
|
Tegra186 has a total of nine I2C controllers that are compatible with
the I2C controllers introduced in Tegra114. Two of these controllers
share pads with two DPAUX controllers (for AUX transactions).
Signed-off-by: Thierry Reding <treding@nvidia.com>
|
|
The initial patch only added UARTA, but there's no reason we shouldn't
be adding all of them. While at it, also specify the missing clocks and
resets for UARTA.
Signed-off-by: Thierry Reding <treding@nvidia.com>
|
|
Tegra186 has six CPUs: two CPUs are second generation Denver CPUs that
support ARMv8 and four CPUs are Cortex-A57 CPUs.
Signed-off-by: Thierry Reding <treding@nvidia.com>
|
|
This adds the initial support of Tegra186 SoC. It provides enough to
enable the serial console and boot from an initial ramdisk.
Signed-off-by: Joseph Lo <josephl@nvidia.com>
[treding@nvidia.com: remove leading 0 from unit-addresses]
[treding@nvidia.com: remove unused nvidia,bpmp property]
Signed-off-by: Thierry Reding <treding@nvidia.com>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/rzhang/linux
Pull thermal managament updates from Zhang Rui:
- Enhance thermal "userspace" governor to export the reason when a
thermal event is triggered and delivered to user space. From Srinivas
Pandruvada
- Introduce a single TSENS thermal driver for the different versions of
the TSENS IP that exist, on different qcom msm/apq SoCs'. Support for
msm8916, msm8960, msm8974 and msm8996 families is also added. From
Rajendra Nayak
- Introduce hardware-tracked trip points support to the device tree
thermal sensor framework. The framework supports an arbitrary number
of trip points. Whenever the current temperature is changed, the trip
points immediately below and above the current temperature are found,
driver callback is invoked to program the hardware to get notified
when either of the two trip points are triggered. Hardware-tracked
trip points support for rockchip thermal driver is also added at the
same time. From Sascha Hauer, Caesar Wang
- Introduce a new thermal driver, which enables TMU (Thermal Monitor
Unit) on QorIQ platform. From Jia Hongtao
- Introduce a new thermal driver for Maxim MAX77620. From Laxman
Dewangan
- Introduce a new thermal driver for Intel platforms using WhiskeyCove
PMIC. From Bin Gao
- Add mt2701 chip support to MTK thermal driver. From Dawei Chien
- Enhance Tegra thermal driver to enable soctherm node and set
"critical", "hot" trips, for Tegra124, Tegra132, Tegra210. From Wei
Ni
- Add resume support for tango thermal driver. From Marc Gonzalez
- several small fixes and improvements for rockchip, qcom, imx, rcar,
mtk thermal drivers and thermal core code. From Caesar Wang, Keerthy,
Rocky Hao, Wei Yongjun, Peter Robinson, Bui Duc Phuc, Axel Lin, Hugh
Kang
* 'next' of git://git.kernel.org/pub/scm/linux/kernel/git/rzhang/linux: (48 commits)
thermal: int3403: Process trip change notification
thermal: int340x: New Interface to read trip and notify
thermal: user_space gov: Add additional information in uevent
thermal: Enhance thermal_zone_device_update for events
arm64: tegra: set hot trips for Tegra210
arm64: tegra: set critical trips for Tegra210
arm64: tegra: add soctherm node for Tegra210
arm64: tegra: set hot trips for Tegra132
arm64: tegra: set critical trips for Tegra132
arm64: tegra: use tegra132-soctherm for Tegra132
arm: tegra: set hot trips for Tegra124
arm: tegra: set critical trips for Tegra124
thermal: tegra: add hw-throttle for Tegra132
thermal: tegra: add hw-throttle function
of: Add bindings of hw throttle for Tegra soctherm
thermal: mtk_thermal: Check return value of devm_thermal_zone_of_sensor_register
thermal: Add Mediatek thermal driver for mt2701.
dt-bindings: thermal: Add binding document for Mediatek thermal controller
thermal: max77620: Add thermal driver for reporting junction temp
thermal: max77620: Add DT binding doc for thermal driver
...
|
|
Enable throttle function for SOC_THERM.
Set "hot" trips for cpu and gpu thermal zones, which
can trigger the SOC_THERM hardware throttle.
Signed-off-by: Wei Ni <wni@nvidia.com>
Signed-off-by: Zhang Rui <rui.zhang@intel.com>
|
|
Set general "critical" trip temperatures for cpu, gpu, mem and pllx
thermal zones on Tegra210, these trips can trigger shut down or reset.
Signed-off-by: Wei Ni <wni@nvidia.com>
Signed-off-by: Zhang Rui <rui.zhang@intel.com>
|
|
Adds soctherm node for Tegra210, and add cpu,
gpu, mem, pllx as thermal-zones. Set critical
trip temperatures for them.
Signed-off-by: Wei Ni <wni@nvidia.com>
Signed-off-by: Zhang Rui <rui.zhang@intel.com>
|
|
Enable throttle function for SOC_THERM.
Set "hot" trips for cpu and gpu thermal zones, which
can trigger the SOC_THERM hardware throttle.
Signed-off-by: Wei Ni <wni@nvidia.com>
Signed-off-by: Zhang Rui <rui.zhang@intel.com>
|
|
Set general "critical" trip temperatures for cpu, gpu, mem and pllx
thermal zones on Tegra132, these trips can trigger shut down or reset.
Signed-off-by: Wei Ni <wni@nvidia.com>
Signed-off-by: Zhang Rui <rui.zhang@intel.com>
|
|
The Tegra132 has the specific settings for soctherm,
so change to use campatible "nvidia,tegra132-soctherm" for it.
And adds cpu, gpu, mem and pllx thermal zones.
Signed-off-by: Wei Ni <wni@nvidia.com>
Signed-off-by: Zhang Rui <rui.zhang@intel.com>
|
|
Enable the XUSB controller on Tegra210 Smaug. The Smaug has a USB Type-C
connector with one of the USB2.0 lanes and one of the USB3.0 lanes
populated.
Signed-off-by: Jon Hunter <jonathanh@nvidia.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
|
