| Age | Commit message (Collapse) | Author |
|---|
|
[ Upstream commit 992d7a8b88c83c05664b649fc54501ce58e19132 ]
Add full-pwr-cycle-in-suspend property to do a graceful shutdown of
the eMMC device in system suspend.
Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Link: https://lore.kernel.org/r/1594989201-24228-1-git-send-email-yoshihiro.shimoda.uh@renesas.com
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
Sort nodes.
If node address is present
* Sort by node address, grouping all nodes with the same compat string
and sorting the group alphabetically.
Else
* Sort alphabetically
This should not have any run-time effect.
Signed-off-by: Yoshihiro Kaneko <ykaneko0929@gmail.com>
Reviewed-by: Simon Horman <horms+renesas@verge.net.au>
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
|
|
Convert bootargs from ip=dhcp to ip=on
Signed-off-by: Magnus Damm <damm+renesas@opensource.se>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
|
|
Successfully tested on H3 ES2.0 and M3-N ES1.0.
Transfer rates where >160MB/s for H3 and >200MB/s for M3-N.
Signed-off-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
Reviewed-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Tested-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
|
|
This patch adds missing ULCB HDMI sound support.
To use sound card, HDMI video is mandatory.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
|
|
ULCB can use daughter board which is called as KingFisher.
It has extra sound interface, thus we want to use it.
But, basically, ALSA SoC can't use Multiple sound card with single
CPU sound interface (= SSI). Thus we need to use Single Sound Card
with multiple DAI interface.
To be easy to expand ULCB sound card on KingFisher, it is better to
use multi-dai-link style sound card on ULCB sound DT.
Now, "simple-audio-card" / "audio-graph-card" both can support
multi-dai-link style, but HDMI sound support (which is not yet supported
on ULCB) needs "audio-graph-card".
Using audio-graph-card is better selection.
This patch exchange current sound card to use it.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
|
|
The eMMC card has two supplies, VCC and VCCQ. The VCC supplies the NAND
array and the VCCQ supplies the bus. On Salvator-X and ULCB, the VCC is
connected to 3.3V rail, while the VCCQ is connected to 1.8V rail. Adjust
the pinmux to match the bus, which is always operating in 1.8V mode.
While at it, deduplicate the pinmux entries, which are now the same for
both default and UHS modes. We still need the two pinctrl entries to
match the bindings though.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Reviewed-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Tested-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
|
|
It can't boot without bootargs settings on Uboot on ulcb board.
This patch adds missing default bootargs.
ulcb BSP can overwrite it by own UBoot settings.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
|
|
The PMIC and EEPROM can operate at 400kHz, so use this speed.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
|
|
Successfully tested on H3 ES1.0 and ES2.0, M3-W ES1.0, and M3-N ES1.0.
Even previously stubborn cards work fine. Transfer rates were >60MB/s.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
|
|
The labels for RWDT device node were named as 2 types now:
- wdt0: r8a7795, r8a7796, r8a77965.
- rwdt: r8a77970, r8a77990, r8a77995.
To be made consistent, this patch unifis the labels as the hardware
name "rwdt".
Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
|
|
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Acked-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Acked-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
|
|
This patch adds definitions for configuration of the power-source,
drive-strength, etc... for the SD2_DS pin for Salvator-X(S) and ULCB
boards.
Signed-off-by: Masaharu Hayakawa <masaharu.hayakawa.ry@renesas.com>
Signed-off-by: Takeshi Kihara <takeshi.kihara.df@renesas.com>
[wsa: fixed for ULCB boards, too]
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
|
|
On the R-Car Starter Kit Premier/Pro, all of the DDR0, DDR1, DDR0C, and
DDR1C power rails need to be kept powered when backup mode is enabled.
Reflect this in the "rohm,ddr-backup-power" property for the BD9571MWV
PMIC node.
The accessory power switch (SW8) is a momentary switch, hense specify
"rohm,rstbmode-pulse".
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
|
|
Add a device node for the ROHM BD9571MWV PMIC.
This was based on the example in the DT binding documentation, but using
IRQ0 instead of a GPIO interrupt, as that matches the schematics, and
because INTC-EX is a simpler block.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
|
|
On other Renesas SoCs, the pin group for the MDIO bus is named "mdio"
instead of "mdc". Fix the inconsistency, now the pinctrl drivers for
R-Car H3, M3-W, and M3-N have gained support for the traditional pin
group name.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
|
|
As the PHY interface installed on the ULCB board provides TX
channel delay, make the "phy-mode" property a board-specific one, meant
to override the one specified in the SoC DTSI.
Follow up patches will reset the r8a7795/96 SoC DTSI to use "rgmii" mode\
and let the board files override that.
Signed-off-by: Jacopo Mondi <jacopo+renesas@jmondi.org>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM SoC device tree updates from Arnd Bergmann:
"We get a moderate number of new machines this time, and only one new
SoC variant (Actions S700):
Actions:
- S700 Soc and CubieBoard7 development board
- Allo.com Sparky Single-board-computer
Allwinner:
- Orange Pi R1 development board
- Libre Computer Board ALL-H3-CC H3 single-board computer
ASpeed ast2x00:
- Witherspoon: OpenPower Power9 server manufactured by IBM that uses the ASPEED ast2500
- Zaius: OpenPower Power9 server manufactured by Invatech that uses the ASPEED ast2500
- Q71L: Intel Xeon server manufactured by Qanta that uses the ASPEED ast2400
AT91:
- Axentia Nattis/Natte digital signage
- sama5d2 PTC-ek Evaluation board
Freescale/NXP i.MX:
- SolidRun Humminboard2 development board
- Variscite DART-MX6 SoM and Carrier-board
- Technologic TS-4600 and TS-7970 development board
- Toradex Colibri iMX7D SoM board
- v1.5 variant of Solidrun Cubox-i and Hummingboard
Freescale/NXP Layerscape:
- Moxa UC-8410A Series industrial computer
Gemini:
- D-Link DNS-313 NAS enclosure
OMAP:
- LogicPD OMAP35xx SOM-LV devkit
- LogicPD OMAP35xx Torpedo devkit
Renesas:
- r8a77970 (V3M) Starter Kit board
- r8a7795 (M3-W) Salvator-XS board
We finally managed to get the dtc warnings under control, with no more
build-time warnings for bad device tree files. This includes fixes for
the majority of platforms, including nomadik, samsung, lpc32xx, STi,
spear, mediatek, freescale, qcom, realview, keystone, omap, kirkwood,
renesas, hisilicon, and broadcom.
Files get rearranged on a few platforms, in particular the Marvell
Armada 7K/8K device tree files are changed in preparation for future
SoC support, based on more than two of the same chips in one package,
and some boards get renamed for oxnas for consistency.
Finally, many existing SoCs gain descriptions for additional on-chip
devices that we can now support with kernel drivers:
- Allwinner A83t (drm, ethernet, i2c, ...), H3/H5 (USB-OTG)
- Amlogic AXG family (clk, pinctrl, pwm, ...), and others (vpu, hdmi)
- Aspeed clk controller support
- Freescale LS1088A, LS1021A device support
- Gemini Ethernet, PCI, TVE, panel
- Keystone gpio, qspi, more uarts
- Mediatek cpufreq, regulator, clock, reset
- Marvell thermal, cpufreq, nand
- Renesas SMP, thermal, timer, PWM, sound, phy, ipmmu
- Rockchip Mipi, GPU, display
- Samsung Exynos5433 PMU, power domain, nfc
- Spreadtrum: sc9860 clocks
- Tegra TX2 PSDI, HDMI, I2C,SMMU, display, fuse, ..."
* tag 'armsoc-dt' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (690 commits)
arm64: dts: stratix10: fix SPI settings
ARM: dts: socfpga: add i2c reset signals
arm64: dts: stratix10: add USB ECC reset bit
arm64: dts: stratix10: enable USB on the devkit
ARM: dts: socfpga: disable over-current for Arria10 USB devkit
ARM: dts: Nokia N9: add support for up/down keys in the dts
ARM: dts: nomadik: add interrupt-parent for clcd
ARM: dts: Add ethernet to a bunch of platforms
ARM: dts: Add ethernet to the Gemini SoC
ARM: dts: rename oxnas dts files
ARM: dts: s5pv210: add interrupt-parent for ohci
ARM: lpc3250: fix uda1380 gpio numbers
ARM: dts: STi: Add gpio polarity for "hdmi,hpd-gpio" property
ARM: dts: dra7: Reduce shut down temperature of non-cpu thermal zones
ARM: dts: n900: Add aliases for lcd and tvout displays
ARM: dts: Update ti-sysc data for existing users
ARM: dts: Fix smartreflex compatible for omap3 shared mpu-iva instance
arm64: dts: marvell: armada-80x0: Fix pinctrl compatible string
arm: spear13xx: Fix spics gpio controller's warning
arm: spear13xx: Fix dmas cells
...
|
|
The present change is a bug fix for AVB link iteratively up/down.
Steps to reproduce:
- start AVB TX stream (Using aplay via MSE),
- disconnect+reconnect the eth cable,
- after a reconnection the eth connection goes iteratively up/down
without user interaction,
- this may heal after some seconds or even stay for minutes.
As the documentation specifies, the "renesas,no-ether-link" option
should be used when a board does not provide a proper AVB_LINK signal.
There is no need for this option enabled on RCAR H3/M3 Salvator-X/XS
and ULCB starter kits since the AVB_LINK is correctly handled by HW.
Choosing to keep or remove the "renesas,no-ether-link" option will
have impact on the code flow in the following ways:
- keeping this option enabled may lead to unexpected behavior since
the RX & TX are enabled/disabled directly from adjust_link function
without any HW interrogation,
- removing this option, the RX & TX will only be enabled/disabled after
HW interrogation. The HW check is made through the LMON pin in PSR
register which specifies AVB_LINK signal value (0 - at low level;
1 - at high level).
In conclusion, the present change is also a safety improvement because
it removes the "renesas,no-ether-link" option leading to a proper way
of detecting the link state based on HW interrogation and not on
software heuristic.
Fixes: dc36965a8905 ("arm64: dts: r8a7796: salvator-x: Enable EthernetAVB")
Fixes: 6fa501c549aa ("arm64: dts: r8a7795: enable EthernetAVB on Salvator-X")
Signed-off-by: Bogdan Mirea <Bogdan-Stefan_Mirea@mentor.com>
Signed-off-by: Vladimir Zapolskiy <vladimir_zapolskiy@mentor.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
|
|
Describe the GPIO used to reset the Ethernet PHY for EthernetAVB.
This allows the driver to reset the PHY during probe and after system
resume.
On ULCB, the enable pin of the regulator providing PHY power is always
pulled high, but the driver may still need to reset the PHY if this
wasn't done by the bootloader before.
Inspired by patches in the BSP for the individual Salvator-X/XS boards
by Kazuya Mizuguchi.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
|
|
"audio_clkout" is dummy clock of <&rcar_sound 0> to avoid clock loop
which invites probe conflict. Thus <&rcar_sound 0> and "audio_clkout"
should be same value.
On commit 2752660a37ae ("arm64: dts: renesas: ulcb: sound
clock-frequency needs descending order") exchanged <&rcar_sound 0>,
but it didn't modify "audio_clkout".
This patch fixup it.
Fixes: 2752660a37ae ("arm64: dts: renesas: ulcb: sound clock-frequency needs descending order")
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
|
|
Since the Ethernet AVB driver doesn't support AVB_PHY_INT handling
and it will be handled by a phy driver as a gpio pin, this patch
removes the "avb_phy_int" from the avb_pins node.
Reported-by: Geert Uytterhoeven <geert+renesas@glider.be>
Fixes: 133ace3f3804 ("arm64: dts: ulcb: Set drive-strength for ravb pins")
Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Acked-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
|
|
The DU is already wired up to the HDMI encoder, all we need to do is
enable it.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
|
|
https://git.kernel.org/pub/scm/linux/kernel/git/horms/renesas into next/dt64
Pull "Renesas ARM64 Based SoC DT Updates for v4.14" from Simon Horman:
* Add usb2.0 for R-Car H3 (r8a7795) ES2.0 SoC
* Add R-Car D3 (r8a77995) SoC and Draak board support
Adds minimal support for the R-Car D3 SoC and the Draak development
board, allowing to boot from a ramdisk using a serial console.
* Add Add VC6 clock generator to R-Car H3 (r8a7795)/Salvator-XS board
The VC6 is an I2C-controlled programmable clock generator, used on the
board to provide a display dot clock. Add it to DT.
* Add missing second pair of DMA names to MSIOF nodes to
R-Car M3-W (r8a7796) SoC
MSIOF0 and MSIOF1 are tied to two DMA controllers through two pairs of
DMA specifiers. However, the second pair of corresponding DMA names was
missing.
* Add support for the DU to R-Car H3 (r8a7795) SoC
Add a compatible string and VSP links to the DU node. The H3 ES1.x and H3
ES2.0 are compatible save for the links to the VSPs that are described
explicitly in DT, so there's no need for a new ES2-specific compatible
string.
* Enable HDMI on R-Car H3 (r8a7795) and M3-W (r8a7796) ULCB boards
* Enable DU on R-Car M3-W (r8a7796) Salvator-X board
* Enable I2C for DVFS on R-Car H3 (r8a7795) and M3-W (r8a7796) ULCB boards
* Add Add DRIF support to R-Car H3 (r8a7795) and M3-W (r8a7796) SoCs
Ramesh Shanmugasundaram says, "R-Car Gen3 DRIF is a SPI like receive only
slave device."
* Move CPG_AUDIO_CLK_I from board to soc files
Geert Uytterhoeven says, "The definition of CPG_AUDIO_CLK_I is
SoC-specific, not board-specific."
* Add IMR-LX4 support to R-Car H3 (r8a7795) and M3-W (r8a7796) SoCs
Sergei Shtylyov says, "The image renderer light extended 4 (IMR-LX4) or
the distortion correction engine is a drawing processor with a simple
instruction system capable of referencing data on an external memory as
2D texture data and performing texture mapping and drawing with respect
to any shape that is split into triangular objects."
* tag 'renesas-arm64-dt-for-v4.14' of https://git.kernel.org/pub/scm/linux/kernel/git/horms/renesas: (31 commits)
arm64: dts: renesas: r8a7795: add hsusb ch3 device node
arm64: dts: renesas: r8a7795: add usb-dmac ch2 and ch3 device nodes
arm64: dts: renesas: r8a7795: add usb2.0 host ch3 device nodes
arm64: dts: renesas: r8a7795: add usb2_phy ch3 device node
arm64: dts: renesas: r8a7795: Add usb companion property in EHCI
arm64: dts: renesas: Add Renesas Draak board support
arm64: dts: renesas: Add Renesas R8A77995 SoC support
arm64: renesas: Add Renesas R8A77995 Kconfig support
arm64: dts: r8a7795: salvator-xs: Connect DU dot clocks 0 and 3
arm64: dts: salvator-xs: Add VC6 clock generator
arm64: dts: r8a7796: Add missing second pair of DMA names to MSIOF nodes
arm64: dts: r8a7795: Add all MSIOF nodes
arm64: dts: r8a7795: Add support for the DU
arm64: dts: ulcb: Enable HDMI output
arm64: dts: ulcb: Add HDMI output connector
arm64: dts: r8a7796: m3ulcb: Add DU external dot clocks
arm64: dts: r8a7795: h3ulcb: Add DU external dot clocks
arm64: dts: ulcb: Add DU external dot clock sources
arm64: dts: r8a7796: salvator-x: Enable HDMI output
arm64: dts: r8a7796: salvator-x: Add DU external dot clocks
...
|
|
Enable the HDMI encoder for ULCB board and hook it up to the HDMI connector.
The HDMI encoder and connector are available on both the H3 and M3-W ULCB boards.
Add them to the ulcb.dtsi file.
Signed-off-by: Vladimir Barinov <vladimir.barinov+renesas@cogentembedded.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
|
|
The ULCB board has one HDMI output connector.
This connector is available on both the H3 and M3-W ULCB boards.
Add this to the ulcb.dtsi file.
Signed-off-by: Vladimir Barinov <vladimir.barinov+renesas@cogentembedded.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
|
|
The DU0/DU1/DU2/DU3 external dot clocks are generated by an I2C-controlled
programmable clock generator.
Clock generator is available on both the H3 and M3-W ULCB boards.
Add this to the ulcb.dtsi file.
Signed-off-by: Vladimir Barinov <vladimir.barinov+renesas@cogentembedded.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
|
|
This enables I2C4 for ULCB board
Signed-off-by: Vladimir Barinov <vladimir.barinov+renesas@cogentembedded.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
|
|
This enables I2C for DVFS device for ULCB board
Signed-off-by: Vladimir Barinov <vladimir.barinov+renesas@cogentembedded.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
|
|
Correct order of sound clock frequencies for ULCB boards
used with r8a7795 and r8a7796 SoCs.
These sounds clock frequencies are used as the ADG clock (output clocks
for audio module) initial setting and sound codec's initial system clock
which needs the maximum clock frequency. Thus, descending order is
required.
Fixes: 9f22774c214ada7b ("arm64: dts: ulcb: add 12288000 for sound ADG")
Signed-off-by: Vladimir Barinov <vladimir.barinov+renesas@cogentembedded.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
[simon: rewrote changelog]
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
|
|
Current rcar_sound only has 11289600 (= for 44.1kHz) clock-frequency,
but it needs 12288000 for 48kHz too.
Otherwise, 48kHz based sound can't handle correctly.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
|
|
The EthernetAVB should not depend on the bootloader to setup correct
drive-strength values. Values for drive-strength where found by
examining the registers after the bootloader has configured the
registers and successfully used the EthernetAVB.
Based on:
* commit 7d73a4da2681 ("arm64: dts: r8a7795: salvator-x: Set drive-strength
for ravb pins")
* commit 4903987033be ("arm64: dts: r8a7796: salvator-x: Set drive-strength
for ravb pins")
Cc: Geert Uytterhoeven <geert+renesas@glider.be>
Cc: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
|
|
The Renesas ULCB development board can be equipped with either an R-Car
H3 or M3-W SiP, which are pin-compatible. Both boards use different
DTBs.
Reduce duplication by extracting common ULCB board support into its own
.dtsi file. References to SoC-specific clocks are handled through cpp
definitions. Sort device nodes while at it.
For H3ULCB, there are no functional changes.
For M3ULCB, the following new devices are now described in DT:
- External audio, CAN, and PCIe clocks,
- CS2000 clock generator,
- AK4613 Audio Codec.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
|
