| Age | Commit message (Collapse) | Author |
|---|
|
Describe the Bluetooth portion of the Ampak combo module - this is
either an AP6356S or an AP6212 depending on the board variant, but
there are no relevant compatibility differences between the two.
Signed-off-by: Robin Murphy <robin.murphy@arm.com>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
|
|
Enable the gpu node and add the supplying regulator
Signed-off-by: Andrius Štikonas <andrius@stikonas.eu>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
|
|
This commit enable the hdmi-sound and i2s2 devices needed to have
audio over HDMI on both rock960 and the related ficus board.
Signed-off-by: Ezequiel Garcia <ezequiel@collabora.com>
Acked-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
|
|
The 'arm,armv8' compatible string is only for software models. It adds
little value otherwise and is inconsistently used as a fallback on some
platforms. Remove it from those platforms.
This fixes warnings generated by the DT schema.
Reported-by: Michal Simek <michal.simek@xilinx.com>
Cc: Mark Rutland <mark.rutland@arm.com>
Cc: Will Deacon <will.deacon@arm.com>
Acked-by: Antoine Tenart <antoine.tenart@bootlin.com>
Acked-by: Nishanth Menon <nm@ti.com>
Acked-by: Maxime Ripard <maxime.ripard@bootlin.com>
Acked-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Acked-by: Chanho Min <chanho.min@lge.com>
Acked-by: Krzysztof Kozlowski <krzk@kernel.org>
Acked-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Acked-by: Gregory CLEMENT <gregory.clement@bootlin.com>
Acked-by: Thierry Reding <treding@nvidia.com>
Acked-by: Heiko Stuebner <heiko@sntech.de>
Acked-by: Simon Horman <horms+renesas@verge.net.au>
Acked-by: Tero Kristo <t-kristo@ti.com>
Acked-by: Wei Xu <xuwei5@hisilicon.com>
Acked-by: Liviu Dudau <liviu.dudau@arm.com>
Acked-by: Matthias Brugger <matthias.bgg@gmail.com>
Acked-by: Michal Simek <michal.simek@xilinx.com>
Acked-by: Scott Branden <scott.branden@broadcom.com>
Acked-by: Kevin Hilman <khilman@baylibre.com>
Acked-by: Chunyan Zhang <zhang.lyra@gmail.com>
Acked-by: Robert Richter <rrichter@cavium.com>
Acked-by: Jisheng Zhang <Jisheng.Zhang@synaptics.com>
Acked-by: Dinh Nguyen <dinguyen@kernel.org>
Signed-off-by: Rob Herring <robh@kernel.org>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
|
|
The mmc.txt didn't explicitly say disable-wp is for SD card slot
only, but that is what it was designed for in the first place.
Remove all disable-wp from emmc or sdio controller.
Signed-off-by: Shawn Lin <shawn.lin@rock-chips.com>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
|
|
After commit ef05bcb60c1a, boot from USB drives is broken.
Fix this problem by enabling usb-host regulators during boot time.
Fixes: ef05bcb60c1a ("arm64: dts: rockchip: fix vcc_host1_5v pin assign on rk3328-rock64")
Cc: stable@vger.kernel.org
Signed-off-by: Dmitry Voytik <voytikd@gmail.com>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
|
|
Ports are described by child 'port' nodes contained in the device node.
'ports' is optional and is used to group all 'port' nodes which is not
the case here.
This patch fixes the following warnings:
arch/arm64/boot/dts/rockchip/rk3399-gru-bob.dts:25.9-29.5: Warning (graph_port): /edp-panel/ports: graph port node name should be 'port'
arch/arm64/boot/dts/rockchip/rk3399-gru-kevin.dts:46.9-50.5: Warningi (graph_port): /edp-panel/ports: graph port node name should be 'port'
arch/arm64/boot/dts/rockchip/rk3399-sapphire-excavator.dts:94.9-98.5: Warning (graph_port): /edp-panel/ports: graph port node name should be 'port'
Signed-off-by: Enric Balletbo i Serra <enric.balletbo@collabora.com>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
|
|
For whatever reason, the sdmmc_dectn function isn't working properly
as-is, and microSD insertion and removal goes unnoticed. Using the pin
as a GPIO interrupt instead is rather noisy without any debouncing, but
is good enough to make it useful until someone feels inclined to figure
out how the vendor kernel/firmware gets the dedicated function to work
with no obvious difference in the pinmux/GRF configuration. Let's also
take the opportunity to tweak the node name so that all related pins
end up grouped together in the compiled DTB.
Signed-off-by: Robin Murphy <robin.murphy@arm.com>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
|
|
In common with most Rockchip reference designs, NanoPC-T4 has a passive
IR receiver connected to PWM3. In lieu of a specialised driver for
PWM-based IR pulse measurement, running the pin as a GPIO with the basic
driver works perfectly well.
Signed-off-by: Robin Murphy <robin.murphy@arm.com>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
|
|
The nanopi4 boards differ primarily in their power trees, with the main
5V and 3.3V rails having very different topologies on the smaller USB-C
powered boards vs. the 12V-powered T4, as well as minor variation in
other regulators related to various external connectors.
Additionally, the recovery key is only present on the T4 - ADC_IN1 is
simply pulled high and not exposed on the other boards - and the lowest
common denominator for MMC speed is actually HS200 according to the
vendor DTs.
Signed-off-by: Robin Murphy <robin.murphy@arm.com>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
|
|
There are a number of subtle differences between the nanopi4 variants,
and where they disagree, the common DTSI currently follows the details
of NanoPi M4. In order to improve matters even more, let's add a
separate DTS for the M4 to which we can start splitting things out
appropriately. The third variant, NanoPi NEO4, is a lot closer to the M4
than either is to the larger T4, so arguably could get away with just
sharing the M4 DT for now (plus I have neither of the smaller boards to
actually test with).
CC: Rob Herring <robh+dt@kernel.org>
CC: Mark Rutland <mark.rutland@arm.com>
Signed-off-by: Robin Murphy <robin.murphy@arm.com>
Reviewed-by: Rob Herring <robh@kernel.org>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
|
|
ROCK Pi 4 is RK3399 based SBC from radxa.com. board has a 1G/2G/4G lpddr4, CSI,
DSI, HDMI, OTG, USB 2.0, USB 3.0, 10/100/1000 RGMII Ethernet Phy, es8316 codec,
POE, WIFI (for Model B only), PCIE M.2 support on board.
This patch enables
- HDMI Display
- Console
- MMC, EMMC
- USB 2.0, USB-3.0
- Ethernet
Signed-off-by: Akash Gajjar <Akash_Gajjar@mentor.com>
Signed-off-by: Pragnesh Patel <Pragnesh_Patel@mentor.com>
Reviewed-by: Rob Herring <robh@kernel.org>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
|
|
This adds a device tree for the NanoPC-T4 SBC, which is based on the
Rockchip RK3399 SoC and marketed by FriendlyELEC.
Known working:
- Serial
- Ethernet
- HDMI
- USB 2.0
All of the interesting stuff is in a .dtsi because there are at least
two other boards that share most of it: NanoPi M4 and NanoPi NEO4.
Signed-off-by: Tomeu Vizoso <tomeu.vizoso@collabora.com>
Reviewed-by: Rob Herring <robh@kernel.org>
[rm: various further cleanup]
Signed-off-by: Robin Murphy <robin.murphy@arm.com>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
|
|
The Rock64 boards has analog audio jack on it. RK3328 can output
analog audio signal using I2S1 and ACODEC core.
This patch adds sound node for analog audio for Rock64.
Signed-off-by: Katsuhiro Suzuki <katsuhiro@katsuster.net>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
|
|
The rk3328 i2s and spdif controllers only ever have one output
connection, so as with all implementations of the rk3066 i2s
controllers we can keep the #sound-dai-cells in the main dtsi
instead of having it repeated in each board.
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
|
|
This patch adds audio codec (ACODEC) node that converts to analog
audio signal from I2S for rk3328.
Signed-off-by: Katsuhiro Suzuki <katsuhiro@katsuster.net>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM Device-tree updates from Olof Johansson:
"As usual, this is where the bulk of our changes end up landing each
merge window.
The individual updates are too many to enumerate, many many platforms
have seen additions of device descriptions such that they are
functionally more complete (in fact, this is often the bulk of updates
we see).
Instead I've mostly focused on highlighting the new platforms below as
they are introduced. Sometimes the introduction is of mostly a
fragment, that later gets filled in on later releases, and in some
cases it's near-complete platform support. The latter is more common
for derivative platforms that already has similar support in-tree.
Two SoCs are slight outliers from the usual range of additions.
Allwinner support for F1C100s, a quite old SoC (ARMv5-based) shipping
in the Lychee Pi Nano platform. At the other end is NXP Layerscape
LX2160A, a 16-core 2.2GHz Cortex-A72 SoC with a large amount of I/O
aimed at infrastructure/networking.
TI updates stick out in the diff stats too, in particular because they
have moved the description of their L4 on-chip interconnect to
devicetree, which opens up for removal of even more of their
platform-specific 'hwmod' description tables over the next few
releases.
SoCs:
- Qualcomm QCS404 (4x Cortex-A53)
- Allwinner T3 (rebranded R40) and f1c100s (armv5)
- NXP i.MX7ULP (1x Cortex-A7 + 1x Cortex-M4)
- NXP LS1028A (2x Cortex-A72), LX2160A (16x Cortex-A72)
New platforms:
- Rockchip: Gru Scarlet (RK3188 Tablet)
- Amlogic: Phicomm N1 (S905D), Libretech S805-AC
- Broadcom: Linksys EA6500 v2 Wi-Fi router (BCM4708)
- Qualcomm: QCS404 base platform and EVB
- Qualcomm: Remove of Arrow SD600
- PXA: First PXA3xx DT board: Raumfeld
- Aspeed: Facebook Backpack-CMM BMC
- Renesas iWave G20D-Q7 (RZ/G1N)
- Allwinner t3-cqa3t-bv3 (T3/R40) and Lichee Pi Nano (F1C100s)
- Allwinner Emlid Neutis N5, Mapleboard MP130
- Marvell Macchiatobin Single Shot (Armada 8040, no 10GbE)
- i.MX: mtrion emCON-MX6, imx6ul-pico-pi, imx7d-sdb-reva
- VF610: Liebherr's BK4 device, ZII SCU4 AIB board
- i.MX7D PICO Hobbit baseboard
- i.MX7ULP EVK board
- NXP LX2160AQDS and LX2160ARDB boards
Other:
- Coresight binding updates across the board
- CPU cooling maps updates across the board"
* tag 'armsoc-dt' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (648 commits)
ARM: dts: suniv: Fix improper bindings include patch
ARM: dts: sunxi: Enable Broadcom-based Bluetooth for multiple boards
arm64: dts: allwinner: a64: bananapi-m64: Add Bluetooth device node
ARM: dts: suniv: Fix improper bindings include patch
arm64: dts: Add spi-[tx/rx]-bus-width for the FSL QSPI controller
arm64: dts: Remove unused properties from FSL QSPI driver nodes
ARM: dts: Add spi-[tx/rx]-bus-width for the FSL QSPI controller
ARM: dts: imx6sx-sdb: Fix the reg properties for the FSL QSPI nodes
ARM: dts: Remove unused properties from FSL QSPI driver nodes
arm64: dts: ti: k3-am654: Enable main domain McSPI0
arm64: dts: ti: k3-am654: Add McSPI DT nodes
arm64: dts: ti: k3-am654: Populate power-domain property for UART nodes
arm64: dts: ti: k3-am654-base-board: Enable ECAP PWM
arm64: dts: ti: k3-am65-main: Add ECAP PWM node
arm64: dts: ti: k3-am654-base-board: Add I2C nodes
arm64: dts: ti: am654-base-board: Add pinmux for main uart0
arm64: dts: ti: k3-am65: Add pinctrl regions
dt-bindings: pinctrl: k3: Introduce pinmux definitions
ARM: dts: exynos: Specify I2S assigned clocks in proper node
ARM: dts: exynos: Add missing CPUs in cooling maps for Odroid X2
...
|
|
Add on-board LED support for Rock960 board based on the following
standard used by rest of the 96Boards:
green:user1 default-trigger: heartbeat
green:user2 default-trigger: mmc0/disk-activity(onboard-storage)
green:user3 default-trigger: mmc1 (SD-card)
green:user4 default-trigger: none, panic-indicator
yellow:wlan default-trigger: phy0tx
blue:bt default-trigger: hci0-power
Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
|
|
Add on-board LED support for Ficus board based on the following
standard used by other 96Boards:
red:user1 default-trigger: heartbeat
red:user2 default-trigger: mmc0/disk-activity (onboard-storage)
red:user3 default-trigger: mmc1 (SD-card)
red:user4 default-trigger: none, panic-indicator
red:wlan default-trigger: phy0tx
red:bt default-trigger: hci0-power
Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
|
|
The rockpro64 does have hdmi support, so add the necessary
devicetree node to enable it.
Signed-off-by: Oskari Lemmela <oskari@lemmela.net>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
|
|
Rockpro64 is not able boot if GPIO1_C1 pin is pulled high
before loading linux kernel.
In rockpro64 GPIO1_C1 pin is connected vdd_cpu_b regulator
VSEL pin. Pin should be pulled down in normal operation and
pulled high in suspend.
PMIC LDO_REG2 is connected to touch panel connector.
Rename regulator and set it to correct voltage.
PCIe power is controller by GPIO1_D0.
Schematics can be downloaded from:
http://files.pine64.org/doc/rockpro64/rockpro64_v21-SCH.pdf
Signed-off-by: Oskari Lemmela <oskari@lemmela.net>
Acked-by: Akash Gajjar <Akash_Gajjar@mentor.com>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
|
|
Add the Video Processing Unit node for the RK3399 SoC.
Also, fix the VPU IOMMU node, which was disabled and lacking
its power domain property.
Reviewed-by: Tomasz Figa <tfiga@chromium.org>
Signed-off-by: Ezequiel Garcia <ezequiel@collabora.com>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
|
|
This adds the 32k clock to the RK3399 Gru board file, which is provided
by a Silego oscillator on Gru boards.
Even though it's not directly used, muxes will end up traversing the
entire clk tree on calls to determine_rate if it doesn't exist. This
is because the 32k clk is listed as a possible parent on some clks.
Since the clk doesn't know about the 32k clk (it was never registered),
it triggers a global search for it. This can happen about 40 times per
second, which isn't great for power.
Signed-off-by: Derek Basehore <dbasehore@chromium.org>
Reviewed-by: Douglas Anderson <dianders@chromium.org>
[moved clock position and adapted commit message a bit]
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
|
|
Each CPU can (and does) participate in cooling down the system but the
DT only captures a handful of them, normally CPU0, in the cooling maps.
Things work by chance currently as under normal circumstances its the
first CPU of each cluster which is used by the operating systems to
probe the cooling devices. But as soon as this CPU ordering changes and
any other CPU is used to bring up the cooling device, we will start
seeing failures.
Also the DT is rather incomplete when we list only one CPU in the
cooling maps, as the hardware doesn't have any such limitations.
Update cooling maps to include all devices affected by individual trip
points.
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
|
|
This patch fixes the wrong polarity setting for the PCIe host driver's
pre-reset pin for rk3399-puma-haikou. Without this patch link training
will most likely fail.
Fixes: 60fd9f72ce8a ("arm64: dts: rockchip: add Haikou baseboard with RK3399-Q7 SoM")
Cc: stable@vger.kernel.org
Signed-off-by: Christoph Muellner <christoph.muellner@theobroma-systems.com>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
|
|
Gru-Scarlet is a tablet device using ChomeOS, dual-dsi display
and Wacom touchscreen with stylus.
There exist two variants in the market using different displays
that are differentiated via their sku-id.
The bootloader on them also determines the correct devicetree to
load via the sku-id.
So add a common scarlet dtsi and two minimal board devicetrees
for the two display variants.
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Reviewed-by: Rob Herring <robh@kernel.org>
|
|
The backlight is for the eDP panel and it has the connector on the excavator baseboard.
Signed-off-by: Vicente Bergas <vicencb@gmail.com>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
|
|
After commit 88ba95bedb79 ("backlight: pwm_bl: Compute brightness of LED
linearly to human eye") the pwm_bl driver is able to calculate a default
brightness table. The calculated table for this PWM will have more
granularity and will be adjusted to change the brightness linearly to
the human eye. Use that table instead of have a DT-defined table with
less granularity.
Signed-off-by: Enric Balletbo i Serra <enric.balletbo@collabora.com>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
|
|
In order to use earlycon, the stdout-path property needs to be set
in the chosen node.
Signed-off-by: Vicente Bergas <vicencb@gmail.com>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
|
|
eMMC that's sold by Pine64 can do HS200, rk3328 can do it
as well, so update DTS to enable it.
Signed-off-by: Vasily Khoruzhick <anarsoul@gmail.com>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
|
|
The Sapphire board has a 12V fan. So, adding it to the DTS.
There is no power supply directly connected, it needs the baseboard to
work.
If the board is used standalone then a hardware modification is needed.
On the Sapphire board there is an unpopulated resistor to connect it to
VBUS_TYPEC, which is usually 5V (too low) and can range up to 20V
(too high).
I tested it for a week connected to VCC_SYS which is 8.4V and proved to
be more than enough for the required cooling needs. This is the
connection described in the comment.
Signed-off-by: Vicente Bergas <vicencb@gmail.com>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
|
|
Add spi dma channels as specified by the rk3399 TRM.
Signed-off-by: Emil Renner Berthing <kernel@esmil.dk>
Tested-by: Enric Balletbo i Serra <enric.balletbo@collabora.com>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
|
|
When the performance governor is set as default, the rock960 hangs
around one minute after booting, whatever the activity is (idle, key
pressed, loaded, ...).
Based on the commit log found at https://patchwork.kernel.org/patch/10092377/
"vdd_log has no consumer and therefore will not be set to a specific
voltage. Still the PWM output pin gets configured and thence the vdd_log
output voltage will changed from it's default. Depending on the idle
state of the PWM this will slightly over or undervoltage the logic supply
of the RK3399 and cause instability with GbE (undervoltage) and PCIe
(overvoltage). Since the default value set by a voltage divider is the
correct supply voltage and we don't need to change it during runtime we
remove the rail from the devicetree completely so the PWM pin will not
be configured."
After removing the vdd-log from the rock960's specific DT, the board
does no longer hang and shows a stable behavior.
Apply the same change for the rock960 by removing the vdd-log from the
DT.
Fixes: 874846f1fccd ("arm64: dts: rockchip: add 96boards RK3399 Ficus board")
Cc: stable@vger.kernel.org
Tested-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
|
|
Enable necessary nodes to get output on the hdmi port of the board.
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
|
|
Add the chain of display nodes from the core display-subsystem
through the one vop to the dw-hdmi output.
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Tested-by: Robin Murphy <robin.murphy@arm.com>
changes in v3:
- drop reg from hdmi-in-port
changes in v2:
- remove trailing 0 from vop irq
|
|
The rk3328 uses a hdmiphy from Innosilicon, so add the necessary node
to the rk3328 soc devicetree.
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Tested-by: Robin Murphy <robin.murphy@arm.com>
|
|
DSI controllers are also the hosts of their dsi bus and therefore contain
nodes describing the attached panels with their reg properties containing
the virtual ids.
The dsi controller nodes on rk3399 lacked the #address-cells and #size-cells
for these subnodes, so add them.
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
|
|
The Pine64 Rock64 board comes with a GigaDevice GD25Q128CSIG
or GD25Q127CSIG chip, which is a 128 Mbit SPI NOR flash chip
that supports the JEDEC read-ID command.
This patch enables the SPI controller and adds a device node
for the flash chip using the generic "jedec,spi-nor" comaptible.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
|
|
Rockpro64 is a rockchip RK3399 based board from pine64.org.
This patch adds basic device node support for Rockpro64 board and make it able
to bring up.
Peripheral Works
- Sdcard
- USB 2.0, 3.0
- Leds
- Ethernet
- Debug console
Not working:
- USB Type-C
Signed-off-by: Akash Gajjar <Akash_Gajjar@mentor.com>
Acked-by: Deepak Das <Deepak_Das@mentor.com>
Reviewed-by: Rob Herring <robh@kernel.org>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
|
|
Enable the newly added controller on the px30 evaluation board.
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
|
|
Add the node for the dwc2-based otg controller on the px30 soc.
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
|
|
For proper working of SD cards, let's add the Card Detect GPIO property
to the common devicetree for Rock960 family boards.
Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
|
|
Add devicetree support for Rock960 board, one of the Consumer Edition
boards of the 96Boards family. This board support utilizes the common
Rock960 family board support that includes Ficus 96Board.
Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
|
|
Since the same family members of Rock960 boards (Rock960 and Ficus)
share the same configuration, split out the common nodes into a common
dtsi file for reducing code duplication. The board specific nodes for
Ficus boards are then placed in corresponding board DTS file.
Below are some of the key differences between both Rock960 and Ficus
boards:
1. Different host enable GPIO for USB
2. Different power and reset GPIO for PCI-E
3. No Ethernet port on Rock960
Only the properties which differ between both boards are placed in the
board specific dts and the reset of the nodes are placed in common dtsi
file.
Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Reviewed-by: Ezequiel Garcia <ezequiel@collabora.com>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
|
|
This patch adds sound card node for rock64. Currently we can support
S/PDIF only. It seems the lack of codec driver of rk3328 to enable
analog audio out.
Signed-off-by: Katsuhiro Suzuki <katsuhiro@katsuster.net>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
|
|
The microSD card slot in the Sapphire board is not working because of
several issues:
1.- The vmmc power supply is missing in the DTS. It is capable of 3.0V
and has a GPIO-based enable control.
2.- The vqmmc power supply can provide up to 3.3V, but it is capped in
the DTS to just 3.0V because of the vmmc capability. This results in a
conflict from the mmc driver requesting an unsupportable voltage range
from 3.3V to 3.0V (min > max) as reported in dmesg. So, extend the
range up to 3.3V. The hw should be able to stand this 0.3V tolerance.
See mmc_regulator_set_vqmmc in drivers/mmc/core/core.c.
3.- The card detect signal is non-working. There is a known conflict
with jtag, but the workaround in drivers/soc/rockchip/grf.c does not
work. Adding the broken-cd attribute to the DTS fixes the issue.
Signed-off-by: Vicente Bergas <vicencb@gmail.com>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
|
|
dtc has new checks for I2C buses. Fix the warnings in unit-addresses.
arch/arm64/boot/dts/rockchip/rk3399-puma-haikou.dtb: Warning (i2c_bus_reg): /i2c@ff3d0000/codec@0a: I2C bus unit address format error, expected "a"
Cc: Heiko Stuebner <heiko@sntech.de>
Cc: linux-rockchip@lists.infradead.org
Signed-off-by: Rob Herring <robh@kernel.org>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
|
|
Add the gpio-controlled regulator and add the supply to the otg-port of phy0.
Signed-off-by: Vicente Bergas <vicencb@gmail.com>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
|
|
This patch fixes pin assign of vcc_host1_5v. This regulator is
controlled by USB20_HOST_DRV signal.
ROCK64 schematic says that GPIO0_A2 pin is used as USB20_HOST_DRV.
GPIO0_D3 pin is for SPDIF_TX_M0.
Signed-off-by: Katsuhiro Suzuki <katsuhiro@katsuster.net>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
|
|
This commit adds WiFi module support for the Firefly-RK3399.
Signed-off-by: Shohei Maruyama <cheat.sc.linux@outlook.com>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
|
